Commit Graph

19975 Commits (adbd9d1f1f07f77b0f511027c1cfea87cefe47be)

Author SHA1 Message Date
Thibaut VARÈNE c6ee683d64 ar71xx: define switch for rb-952ui-5ac2nd
QCA9533 built-in switch can be configured

Tested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 18:14:30 +02:00
Mantas Pucka 3dd692cd6b ipq40xx: fix booting secondary CPU cores
95672e04 broke booting secondary cores by removing 'qcom,saw' property
from L2 cache node. kpssv2_release_secondary() requires it.

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2018-07-30 17:55:04 +02:00
John Crispin eddf4eae97 ar71xx: fix TL-WR1043N v5 port mapping
fixes 5660c8fb20 ("ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.")

Signed-off-by: John Crispin <john@phrozen.org>
2018-07-30 17:47:06 +02:00
Tim Thorpe 5660c8fb20 ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.
Reversed the numbering of the LAN ports in Luci so as to match the port numbers on the housing.

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
2018-07-30 16:31:18 +02:00
Tim Thorpe d834ad9ac3 ar71xx: TL-WR1043N v4/v5: add orange WAN LED support
Add missing definitions for the orange WAN LED on the
TL-WR1043N(D) v4 and v5.

Change the name of a MAC address offset constant to
make it consistent with the format of the
existing constants.

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
2018-07-30 16:30:34 +02:00
Lucian Cristian accb67e582 ath79: add support for tl-wr841n-v9
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 16:14:49 +02:00
INAGAKI Hiroshi ce93445cd6 ramips: add support for ELECOM WRC-2533GST
ELECOM WRC-2533GST is a 2.4/5 GHz band 11ac rotuer, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Core, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 4T4R 2.4/5 GHz wifi
  - MediaTek MT7615
- 5x 10/100/1000 Mbps Ethernet
- 4x LEDs, 6 keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Connect the computer to the LAN port of WRC-2533GST
2. Connect power cable to WRC-2533GST and turn on it
3. Access to "https://192.168.2.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用")
button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-07-30 15:55:21 +02:00
Paul Spooren 869b0d11db imagebuilder: add function to show manifest
Tested with 18.06.0-rc2/ar71xx/generic/tl-wdr4300-v1, image & list

This PR is based on the work of @fewckert[1] with slight improvements.

Add function `manifest` to show the manifest of the produced image,
before actually building it. The manifest contains an orderd list of
package name and version.

This is usefull to check package dependencies but also determine a
unique and reproducible image name before building the package. The
sysupgrade server[2] builds images on request with individual package
selection. To distignish between created images which contain differnt
packages, the EXTRA_IMAGE_NAME is set to a shortend hash of the
manifest's content. So far the image was renamed afterwards as the
manifests content was unknown, however this corrupts the signed
sha256sums. This patch allows a clean solution as to dtermine the
manifest in advance and set the EXTRA_IMAGE_NAME accordingly.

[1]: https://github.com/lede-project/source/pull/1591
[2]: https://github.com/aparcar/attendedsysupgrade-server

Signed-off-by: Paul Spooren <mail@aparcar.org>
2018-07-30 15:55:21 +02:00
Kjel Delaey 8492ad0cc1 x86: add support to set GRUB menu entry title
$ make menuconfig

        Target Images -> Title for the menu entry in GRUB

Signed-off-by: Kjel Delaey <kjel_delaey@hotmail.com>
2018-07-30 15:55:21 +02:00
Ademar Arvati Filho 27b2f0fc0f kirkwood: add support for Iomega Storcenter ix2-200
Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell
 Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of
 flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC

Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1000Mhz
- Flash-Chip: Hynix NAND
- Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16
- RAM: 256MB
- LAN: 1x 1000 Mbps Ethernet
- WiFi: none
- 3x USB 2.0
- UART: for serial console

Installation instructions - easy steps:
1. download factory.bin and copy into tftp server
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    setenv serverip 192.168.1.1
    setenv ipaddr 192.168.1.13
    tftpboot 0x00800000 factory.bin
    nand erase 0x100000 $(filesize)
    nand write 0x00800000 0x100000 $(filesize)
    run bootcmd
    ```
3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Installation steps nand bad blocks proof:
1. download initramfs-uImage and copy into usb ext2 partition
    ```
    mkfs.ext2 -L ext2 /dev/sdh1
    mount -t ext2 /dev/sdh1 /mnt
    cp initramfs-uImage /mnt/initramfs.bin
    umount /mnt
    ```
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000
    ```
3. log into openwrt and sysupgrade to install into flash
    ```
    sysupgrade -n /tmp/sysupgrade.bin
    ```
4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-30 15:21:00 +02:00
Jianhui Zhao 84c212da44 samsung/s5pv210: New target
Signed-off-by: Jianhui Zhao <jianhuizhao329@gmail.com>
2018-07-30 14:10:00 +02:00
Keith Maika 4caab80830 ar71xx: add support for TP-Link Archer C59 v2
TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB

Flash instruction:
  - via web UI:
    1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
    2. Login to router and open the Advanced tab
    3. Navigate to System Tools -> Firmware Upgrade
    4. Upload firmware using the Manual Upgrade form
  - via TFTP:
    1. Set PC to fixed ip address 192.168.0.66
    2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
       and rename it to tp_recovery.bin
    3. Start a tftp server with the file tp_recovery.bin in its root directory
    4. Turn off the router
    5. Press and hold Reset button
    6. Turn on router with the reset button pressed and wait ~15 seconds
    7. Release the reset button and after a short time
       the firmware should be transferred from the tftp server
    8. Wait ~30 second to complete recovery.

Signed-off-by: Keith Maika <keithm@aoeex.com>
2018-07-30 14:04:45 +02:00
Rafał Miłecki a3d2448fae kernel: add missing include to redboot.c
This fixes:
drivers/mtd/redboot.c:299:34: error: array type has incomplete element type 'struct of_device_id'

Fixes: 5e8b4be531 ("kernel: add DT binding support to the mtd redboot parser")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-30 12:07:06 +02:00
Rafał Miłecki 23197e4580 brcm63xx: update DT RedBoot binding for the Inventel Livebox 1
linux,part-probe should be avoided as its only supported with OpenWrt
downstream patch that is going to be dropped eventually.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-07-30 11:16:42 +02:00
Jo-Philipp Wich d7d10f2c1e brcm47xx: rework model detection
On brcm47xx boards, the model ID is the combination of the "boardtype" nvram
variable and an optional supplemental "boardnum" variable while the human
readable model name is usually exposed in the "machine" field of the
/proc/cpuinfo file.

Move the extraction of the board nvram variables and model name string into
the 01_sysinfo file and rework the 01_detect board configuration script to
solely use the prepared sysinfo values without performing own detection
logic.

As a consequence, we can drop the ucidef_set_board_id() and
ucidef_set_model_name() invocations in favor to the generic behaviour
which copies the /tmp/sysinfo/{board_name,model} values into the board.json
"id" and "name" fields respectively.

Since "01_detect" only contains network configuration logic after this
change, move it to "01_network" and rename the contained "detect_by_xxx"
functions to "configure_by_xxx" instead, to avoid potential confusion.

Fixes FS#1576
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-07-30 11:10:47 +02:00
Lucian Cristian 569b6c8246 omap: disable ubifs
ubifs image are not working, until there is a fix, disable them

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 11:03:02 +02:00
Lucian Cristian ca529e60d2 omap: add support for f2fs/ext4 overlay creation
add kernel support and include the tools for creating an overlay partition (f2fs or ext4)

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 11:03:02 +02:00
Lucian Cristian 6a095e8587 omap: add sysupgrade support
add sysupgrade missing script files

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 11:03:02 +02:00
Lucian Cristian 40f66f1431 omap: rename image for sysupgrade compatibility
for sysupgrade to work we need to change the image name based on dts target name

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 11:03:02 +02:00
Lucian Cristian f9af9be8ab omap: fix squashfs image boot and creation
fixes FS#1034, squash fs images fails to boot because of missing ARM BCJ filter decoder
also activate squashf image creation

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 11:03:02 +02:00
Mathew McBride 08714738d2 layerscape: add Traverse LS1043-S support
The Traverse LS1043-S board is a router board based on
NXP/Freescale's LS1043 SoC, with 4x1GBase-T, 1 SFP and 1 SFP+,
as well as miniPCIe and M.2 LTE.

Unlike the Layerscape reference boards, the LS1043-S board has
NAND flash and uses the mainline U-Boot.

This patch implements support for the LS1043-S board, as well as
the earlier LS1043-V board. It is our intention that all boards
in this family (LS1043-S and later, Five64) will boot the same binary.

Not included in this patchset are the hwmon drivers not in the kernel
(emc1704,pac1934) or the bootloader.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-07-30 10:53:57 +02:00
Mathew McBride 481f870a02 layerscape: add multiple-configuration generator for FIT images
This is required for the Traverse LS1043 family, we generate a FIT image
that works on all boards across the family. This is done by creating
multiple configurations that select the right DTB for the board.

The bootloader on these boards is configured to boot like this:
bootm $kernel_load#ls1043s
bootm $kernel_load#ls1043v

This is based on earlier work by Jason Wu for Zynq:
https://lists.openwrt.org/pipermail/openwrt-devel/2016-March/040460.html

Modified to add FDT load addresses and multiple configurations with DTB.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-07-30 10:53:57 +02:00
Mathew McBride 2203815f05 layerscape: add support for fixed-link on RGMII interfaces
This is required on the Traverse LS1043 boards to support SFP
and xDSL plug-ins.

This will not be needed on kernel 4.14.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-07-30 10:53:57 +02:00
Mathew McBride 40120ca670 layerscape: enable QorIQ thermal driver
This provides access to the CPU die temperature sensor and
the thermal throttling integration

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-07-30 10:53:57 +02:00
Mathew McBride efc1096ef0 layerscape: remove DEVICE_TYPE=developerboard
The Traverse LS1043 series are router boards and need the default router package
selection

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2018-07-30 10:53:57 +02:00
Pawel Dembicki aa5838adb7 kernel: generic: fix problem with w1-gpio-custom
In boards with fdt is impossible to use kmod-w1-gpio-custom.
w1-gpio-custom create platform structure for w1-gpio module,
but if board use fdt, data is ignored in w1-gpio probe.

This workaround fix the problem.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-07-30 10:43:37 +02:00
Thibaut VARÈNE 3fd4db76b0 ramips: fix RBM11G name
The device name is corrected to match the hardware-stored (in hard config
flash space) device name.

Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:43:37 +02:00
Thibaut VARÈNE a9494bb425 ramips: fix RBM33G name
The device name is corrected to match the hardware-stored (in hard config
flash space) device name.

Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:43:37 +02:00
LoveSy 974a2b1aa9 ramips: mmc: Add SD card support to HC5661A
Tested on HC5661A and it now fixes the issue that when enabling sd card
in HC5661A, the wan and 3 lan ports will down.

Known issue:
- When enabling SD card support, the led light of system will down and the rest 2 lights keep working.

Signed-off-by: LoveSy <shana@zju.edu.cn>
2018-07-30 10:43:37 +02:00
LoveSy 3a8efaef00 ramips: mmc: Fix init for MT7628AN
There is another thing about crc to do when initialize SD card on
MT7628.
This commit is to fix this init issue.

Signed-off-by: LoveSy <shana@zju.edu.cn>
2018-07-30 10:43:37 +02:00
张鹏 53a4502013 ar71xx:add support for E750G v8
Qxwlan E750G v8 is based on Qualcomm QCA9344.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4G GHz (AR9344)
 - 2x 10/100 Mbps Ethernet (PoE support)
 - 2x 10/100/1000 Mbps Ethernet
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
2018-07-30 10:43:36 +02:00
张鹏 ac03d51a3f ar71xx:add support for E750A v4
Qxwlan E750A v4 is based on Qualcomm QCA9344.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 5G GHz (AR9344)
 - 2x 10/100 Mbps Ethernet (one port with PoE support)
 - 1x miniPCIe slot (USB 2.0 bus only)
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
2018-07-30 10:43:36 +02:00
张鹏 b74f63f81d ar71xx:add support for E558 v2
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.

Specification:

 - 720/600/200 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4 GHz (QCA9558)
 - 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
 - 4x miniPCIe slot (USB 2.0 bus only)
 - 1x microSIM slot
 - 5x LED (4 driven by GPIO)
 - 1x button (reset)
 - 1x 3-pos switch
 - 1x DC jack for main power input (9-48 V)
 - UART (JP5) and LEDs (J8) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
2018-07-30 10:43:36 +02:00
Daniel F. Dickinson 7a3e133751 ar71xx: ag71xx: Prevent kernel oops for board def
The driver is written in such a way that with a board defintion that
connects a fixed phy, mdio, and switch in a certain way, a kernel oops could
result because of lack of previously probed mdio bus.

This commit allows for easier debugging in this case by casting the
correct blame with serial console messages.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:36 +02:00
Daniel F. Dickinson 0b9f4e8808 ar71xx: ag71xx: Add connect message: fixed phy
It's a little noisier but makes it obvious when the ar7240 switch was
connected to the MDIO bus, and to which phy device (or the failure
to do so).

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:35 +02:00
Daniel F. Dickinson 2655fbe8ef ar71xx: ag71xx_phy: Fix compilation for debug messages
NB: Error only appears with ag71xx debug messages and dynamic printk
enabled.  This is probably why no one has caught it before.

Previously phy probe debug messages used old (now wrong) functions
to get the phy name for printing.  There was also the chance of
a NULL pointer in the event no phy_device was found.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo 7a07b4cff0 ath79: Add switch reset definition in dts
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo f593020a28 ath79: ag71xx: assert a switch reset if defined in dts.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo a5fa6b3825 ath79: ar724x: Fix reset definition for gmac0/gmac1
reset bit 8 is for builtin switch and bit 12 is marked 'reserved' on datasheet.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo 4e5ba50760 ath79: ar7240: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo f43e8f9004 ath79: ag71xx: Explicitly register mdio bus after ag71xx_hw_init() for ar7240
mdio bus isn't a standalone device on ar7240. (and maybe older SoCs?)
Use simple-mfd for ar7241 and later SoCs to get mdio1 ready before gmac0
For ar7240 and older chips, manually create platform device after
ag71xx_hw_init() in ag71xx_probe()to get mdio0 ready between
ag71xx_hw_init() and ag71xx_phy_connect().

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:35 +02:00
Chuanhong Guo 85189e4c00 ath79: ag71xx: Rework mdio clock settings
Allow specifying desired mdio clock frequency in dts.
Use default frequency around 5MHz for builtin switch and 2MHz for other mdio bus.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo bb7fac4369 ath79: ar7242: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo 113b4cf90f ath79: ar7241: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo b6c8e5deae ath79: Fix support for TP-LINK Archer C7 v2
Remove mdio1 and phy1 handle. AR8327N is controlled through mdio0.
Add gmac-config for Archer C7.
Remove ucidef_set_interfaces_lan_wan. They can be determined by config_generate automatically.

The following are for adding support for WDR4900 v2/Archer C7 v1 and other
devices that shared the same machine file in ar71xx:
Move mtd partitions to archer-c7-v2.dts. Only Archer C7 v2 has 16M flash.
Flash on Archer C7 v1/TL-WDR4900 v2 is 8M.
Add label for wlan leds. The default trigger for archer c7/wdr4900 is different.
Move wlan5g led to archer-c7-v2.dts. 5G led on WDR4900 is connected to ar9380.
Move rfkill definition to archer-c7-v2.dts. There is no such a button on wdr4900 v2.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo 18db385eb7 ath79: qca955x: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo b7a10772d1 ath79: qca956x: Update dts for current ag71xx driver
enable mdio1 by default because mdio1 node is a subnode of eth1
and eth1 node is a "simple-mfd", which makes mdio1 disabled when
eth1 isn't enabled.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo fc1f55ebf4 ath79: qca953x: Add chosen node and specify console in bootargs
Most qca devices use 115200n8 as it's default uart baudrate.
Add 'chosen' node for qca953x like other SoCs in ath79 target.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo e8245c5b3f ath79: qca953x: Update dts for current ag71xx driver
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Lucian Cristian e6417390e0 ath79: update qca9533 to new irq driver
Commit c7efc93 renamed controller name
to qca,ar9340-intc and added some functions but qca9533.dtsi was overlooked.
Correct the dtsi and adust it to the new format

Add gmac and correct reset for cascaded irq and build-in switch
Also add the reference clock to soc dtsi so we don't have to have it in every dts

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>

Remove switch reset definition
Fix gmac compatible string (We only need SW_PHY_SWAP and SW_PHY_ADDR_SWAP on qca953x so use ar9330-gmac instead of ar9340-gmac.)

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:34 +02:00
Chuanhong Guo c7c807cb8c ath79: ar933x: Update dts for current ag71xx driver
gmac0 is always connected to switch phy4 and mdio1 is always needed.
So add phy handle for eth0 and enable mdio1 by default.
Move fixed-link for gmac1 from device dts to ar9331.dtsi because gmac1 is always connected to builtin switch.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo f6c99241ba ath79: ar934x: Update dts for current ag71xx driver
Enable mdio1 by default because mdio1 is needed when eth1 is enabled.

PS: If a ar9341 device has only one port and you only want to use gmac0,
change compatible of gmac1 to "syscon", "simple-mfd" in dts.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo 7ae9e63719 ath79: ag71xx: Make builtin switch driver a separated module
This patch did several things:
1. Probe the builtin switch as a separated mdio device.
2. Register a separated mdio bus for builtin switch.
3. Use generic mdio read/write function instead of calling ag71xx_mdio_mii_read/write directly.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo 83d2dbc599 ath79: ag71xx: Split mdio driver into an independent platform device.
We need to have mdio1 belonging to gmac1 initialized before gmac0.
Split it into a separated mdio device to get both mdios ready before probing gmac.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo 24cbe27bb7 ath79: ag71xx: Remove ar7240_set_addr and ag71xx_ar7240_start
The builtin switch has it's initial valid mac address(00:00:01:00:00:00).
Since the builtin switch is an independent device, setting mac address of gmac1 to builtin switch isn't a good idea and this makes it impossilbe to split builtin switch apart as an independent platform device.
Remove these functions and apply default VLAN during initialization as a preparation for further driver splitting.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo 2d081addb5 ath79: ag71xx: Split gmac config into separated file and add support for ar934x/qca955x.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Chuanhong Guo b346c37588 ath79: Fix mac reset and gmac compatible in ar934x.dtsi
Also add phy-mode and fixed-link as gmac1 is always connected
to the builtin switch.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-30 10:43:33 +02:00
Daniel F. Dickinson 098267db4c ar71xx: cap324: Drop support for defunct cloud
Only build images for straight OpenWrt (using all flash; wipes out
partitions that contain information only important for accessing a
now defunct cloud service with the stock firmware) since the stock
firmware is now irrelevant.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:33 +02:00
Daniel F. Dickinson 37ab944ac5 ar71xx: cap324: Use correct company name
It's 'PowerCloud Systems' not just 'PowerCloud'

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson 739eaae9ca ar71xx: cap324: Use correct MAC addresses
The wrong MAC addresses (from the point of view of the physical device
label) were being assigned to the wrong interfaces.  Fix that.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson d2f7dba309 ar71xx: cap324: Use standard eth as static lan
While the stock firmware and previous ar71xx versions of openwrt used the
single ethernet port as a DHCP client, for unmodified openwrt usage it
makes more sense to do the standard openwrt thing and make the ethernet
port a static lan with known address so that users can find the device on
the network more easily.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson fedc826c32 ar71xx: cr5000: use correct company name
It's 'PowerCloud Systems' not just 'PowerCloud'

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson 50caf9d452 ar71xx: cr5000: Drop support for defunct cloud
The Skydog cloud service no longer exists hence supporting going back
to stock firmware with cloud support is no longer applicable.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson c666851ce7 ar71xx: cr5000: Tweak switch LED settings
This is basically cosmetic and sets the Port 1-4 LEDs to blink on
10/100/1000M.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson ffc71cd2d0 ar71xx: cr5000: Fix the reset button as KEY_RESTART
The reset button was incorrectly returning KEY_WPS_BUTTON as the key
code.  We want KEY_RESTART., so make that fix.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson a208e07790 ar71xx: cr5000: board data: Use better macro name
The PCIe wireless MAC address address is better labelled as WMAC
than MAC to emphasize that it is for a wireless interface.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:32 +02:00
Daniel F. Dickinson 915966d861 ath79: Port PowerCloud Systems CAP324 support
The CAP324 was an AP for a NaaS offering that is now defunct.  While
previously supported in the ar71xx arch, there were some errata (to
be fixed shortly).

Notable differences from ar71xx support:

1) The method of getting the ath9k firmware for the PCIe 2ghz wifi has
changed (due to changes in how the arch handles this), since this device
doesn't use the EEPROM except to get the MAC address of the wifi.

2) /etc/config/wireless will need to be regenerated as the path(s) to
the wireless device(s) have changed.

3) ath79 OpenWrt firmware no longer supports build an image that allows
reverting to stock firmware (as the cloud service no longer exists, the
stock firmware is useless), instead using all of the flash for image and
overlay (less u-boot/env and art).

4) Initial network config treats the ethernet port as a Lan port with
the standard default address (192.168.1.1 unless changed in .config
--e.g. via menuconfig) instead of using DHCP (this was the default for
the stock firmware, however for openwrt use this is rather confusion and
counter-productive as the user has a harder time finding the device on
the network.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:31 +02:00
Daniel F. Dickinson 4b93cbd172 ath79: Port PowerCloud Systems CR5000 support
Add ath79 arch support for PowerCloud Systems CR5000.  Previously
supported under ar71xx (however there are some errors in that support;
to be fixed shortly).

Info:

* This board is based on the Atheros DB120 reference design, but doesn't
  use the on-board switch.  Instead it attachs GMAC0 to an AR8327 switch.
* It only uses GMAC0 and the WAN is simply a VLAN in the stock firmware.
* It has 64MB RAM and 8MB flash.
* In the dts version we get rid of using 'open-drain' for the AR8327
  LED controls.
* As with the platform data version we disable JTAG as this conflicts
  with one of the pair of GPIO's required for the power/status LED
  (GPIO2 and GPIO4 are used for this LED).
* The pcie card wifi has an EEPROM but gets it's MAC address from
  the ART partition.
* The SoC wifi (2.4 GHz) is all from the ART.
* The USB is support comes from the SoC.

NB. This is actually an AR9342 rather than AR9344 but we use the 9344
definitions because there are no relevant differences for this board.

NB: Building only images that don't support reverting to the old
cloud-based firmware as the Skydog cloud service for the CR5000 no
longer exists.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-07-30 10:43:31 +02:00
Thibaut VARÈNE 091e915d99 ar71xx: improve MikroTik wAP R support
81d446b045 introduced incomplete
support for this device.

This patch attempts to correct the situation based on OEM source
code.

LED1-3 are GSM mode on OFW (2G/3G/4G) hence unassigned here.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: David Ehrmann <ehrmann@gmail.com>
2018-07-30 10:35:11 +02:00
Thibaut VARÈNE 5c2419b6f8 ar71xx: add missing diag LED support for RB wAP 2nD
3b15eb06c3 did not include diag.sh
edit

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:35:11 +02:00
Thibaut VARÈNE e76c048d34 ar71xx: rbspi: mark rb911L user led as active low
The active_low flag was missing for the user LED. This LED is open drain
(confirmed in OEM source) and open drain only makes sense for active low
GPIOs.

The two wireless LEDs mentioned in the comments are also #defined for
future reference.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Ryan Mounce <ryan@mounce.com.au>
2018-07-30 10:35:11 +02:00
Thibaut VARÈNE e99f760235 ar71xx: rbspi: fix RB wAP AC gpio conflict and LED
e15c63a375 introduced code that was trying
to register GPIO 1 as both an LED and a button. The OEM source makes it
clear that LED1 is not wired to the SoC GPIOs. GPIO 1 is the reset button.

Furthermore the (green) power led default state should also be defined,
(matching OEM source), and it should be used by diag.sh since it's
currently the only software-controllable LED.

This patch fixes these issues and renames the corresponding #defines for
clarity

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:35:11 +02:00
Thibaut VARÈNE 03562bfcdb ar71xx: rbspi: clarify USB power gpios action
The gpios that control power toggle for USB on the RouterBOARD devices
are active low _off_ switches.

When they are active (low), power is off. When they are inactive
(high), power is on.

Rename GPIO defines, set gpios to GPIOF_ACTIVE_LOW for consistency and
reflect their true action in the display name. This brings openwrt code
in line with OEM.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Ryan Mounce <ryan@mounce.com.au>
2018-07-30 10:35:11 +02:00
Rafał Miłecki 5e8b4be531 kernel: add DT binding support to the mtd redboot parser
It allows using that parser with the "compatible" set in DT.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-30 08:39:52 +02:00
Christian Lamparter b70d3557e0 apm821xx: clean up gpio-hogs
convert the usb and both sata port power related gpio-hogs to
what they really are: fixed-regulators.

The ethernet phy-reset gpio-hog is replaced by a proper
upstream (4.15+) reset-gpios property in the mdio-node.
So this will work eventually.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-07-30 08:12:32 +02:00
Christian Lamparter cff6548948 apm821xx: split MBL's rootfs.img.gz into a sysupgrade and factory image
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>

The MBL's rootfs.img.gz image is generated in much the same way.
Hence this patch preemptively splits the rootfs.img.gz image into
a sysupgrade and a factory image.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-07-30 08:12:13 +02:00
Christian Lamparter aed4799d6d apm821xx: build squashfs-rootfs images for the MBL
This patch adds support for squashfs as the root filesystem.

advantages:
 - migrate from a existing -ext4 installation and back
   with the sysupgrade utility
 - existing partition layout will not be lost during switch
 - slightly smaller image size as compared to the -ext4 image.

disadvantages:
 - needs f2fs + tools. This is because fstools rootdisk.c decides based
   on the partition size (currently root partitions > 100 MiB) f2fs is
   used as the rootfs_data filesystem.
 - rootfs_data is placed into the rootfs partition after the squashfs.
   This makes it difficult for tools that expect a /dev/sda${X} device.
   It also makes it difficult for data recovery tools as they might not
   expect to find a embedded partition or will be slightly confused.
   ... or will not support f2fs.

For people with existing build configurations: make sure to include mkf2fs
and f2fsck packages into the image. Otherwise the new -squashfs image will
only boot from the ram-overlay.

Note:
All overlay data (configurations/all installed packages/...) will be
placed in inside the rootfs partition (i.e. /dev/sda2) just after the
squashfs image.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-07-30 08:11:56 +02:00
Christian Lamparter 7516a96011 brcm2708: split sdcard.img.gz into a sysupgrade and factory image
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>

@blogic told me to split the single sdcard.img.gz for the RPi
into a sysupgrade and a factory image for all brcm2708 targets.
The factory images will have no metadata attached, this way
these utilities that can't deal with the attached metadata will
not fail for no reason.

Cc: John Crispin <john@phrozen.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-07-30 08:11:36 +02:00
Jonas Gorski 7880a6f7fe brcm63xx: drop linux,part-probe usage where possible
It was present as 4.4 compatibility, but since we now use 4.9 or later
with the new upstream solution, we don't need it anymore.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-07-29 15:38:33 +02:00
Jonas Gorski abb28bec25 brcm63xx: drop own implementation of DT partitions in favour of upstream
The binding works the same, so we can just drop the revert and the patch.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-07-29 15:38:33 +02:00
Rafał Miłecki 0417b08b06 bcm53xx: revert SPI controller commit breaking flash reads
That upstream commit caused instability in flash reads. It was reported
but there isn't any proper fix as for now.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-29 11:02:57 +02:00
Rafał Miłecki a07730472c bcm53xx: backport BCM5301X/BCM53573 dts commits from 4.19+
This includes Linksys EA9500 support, BCM53573 timer fix and
upstream-ready partitions patch that replaces two downstream hacks.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-28 21:48:10 +02:00
Rafał Miłecki 8a175ea219 bcm53xx: switch USB 3.0 PHY DT description to use MDIO bus
USB 3.0 PHY is attached to the MDIO bus and should be supported
(accessed) as a MDIO device. This wasn't known initially which resulted
in writing driver that was working with MDIO bus (using some magic
values) without knowing it.

This commit updates DT to properly describe MDIO & USB 3.0 PHY and
enables required kernel drivers.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-28 21:46:08 +02:00
Rafał Miłecki 5c8b8a3fd4 bcm53xx: backport DT fix for I2C controller interrupt
Specified interrupt type was incorrect.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-28 21:36:33 +02:00
Rafał Miłecki 2a598bbaa3 kernel: backport mtd support for subpartitions in DT
This is a new & warm feature that allows nesting partiitons in DT and
mixing their types (e.g. static vs. dynamic). It's very useful for
boards that have most partitions static but some of them require extra
parsing (e.g. a "firmware" partition).

It's required to successfully backport support for new devices using
that new syntax in their DT files.

Since brcm63xx has a custom alternative patch the upstream one is being
reverted for it. The plan is to make brcm63xx use the upstream
implementation.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-27 22:16:24 +02:00
Rafał Miłecki 4c1aa64b4d brcm47xx: revert upstream commit breaking BCM4718A1
This fixes kernel hang when booting on BCM4718A1 (& probably BCM4717A1).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-27 15:58:51 +02:00
Rafał Miłecki 6bcafea2c0 kernel: backport mtd patches with Broadcom of_match_table-s
Two tiny & trivial patches with no regression risk. One simplifies
bcm53xx downstream patch.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-27 15:55:01 +02:00
John Crispin ffc40d2eae ipq40xx: move essedma patches into same range
Signed-off-by: John Crispin <john@phrozen.org>
2018-07-25 12:13:19 +02:00
John Crispin e725d3080c ipq40xx: sync kernel config
Signed-off-by: John Crispin <john@phrozen.org>
2018-07-25 12:13:18 +02:00
John Crispin 95672e0433 ipq40xx: use patches that were sent upstream
Signed-off-by: John Crispin <john@phrozen.org>
2018-07-25 12:13:18 +02:00
John Crispin e8c58e7ddd ipq40xx: move dts file patches to end of series
Signed-off-by: John Crispin <john@phrozen.org>
2018-07-25 12:00:21 +02:00
John Crispin c913288844 ipq40xx: cleanup USB support
remove the 2 USB PHY drivers and add a generic PHY driver instead

Signed-off-by: John Crispin <john@phrozen.org>
2018-07-25 12:00:21 +02:00
John Crispin 3d456a50f4 ipq40xx: drop no-op cpu_idle symbol patch
Signed-off-by: John Crispin <john@phrozen.org>
2018-07-25 12:00:21 +02:00
David Bauer 5409dcffbd ath79: fix OCEDO Raccoon
The OCEDO Raccoon only has one ethernet port, but currently uci sections
for WAN and LAN are created.

Additionally, newer versions of the devices U-Boot (units with SteelWRT)
set the kernel-cmdline and therefore overwrite the partition-layout.
We fix this by overwriting the cmdline supplied by the bootloader.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-07-25 08:59:33 +02:00
Mathias Kresin 4cbf5601f9 ramips: remove stale get_status_led call
The get_status_led() function was removed due to the convertion to dts
alias based status led.

Since we don't need the boardname any longer, the functions.sh include
isn't required any more.

Fixes: c9c4b2116c ("ramips: Use dts alias based status led")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-25 08:57:17 +02:00
Mathias Kresin 3716b5e4e6 kernel: don't auto attach ubi on read error
With a10a204aab ("kernel: make ubi auto-attach check for a tar file
magic") the check for the magic was added without considering a failing
mtd_read(). If the read fails, no check is done and the mount code is
called straight away.

Failing with an error message for such cases seems to me the cleaner way,
as it would allow to spot hidden/workaround issues.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-24 22:24:21 +02:00
Mathias Kresin 0ac91d82ed kernel: handle bad blocks in ubi auto attach code
The first block(s) of the ubi mtd device might be bad. We need to take
care on our own to skip the bad block(s) and read the next one(s).

Don't treat recoverable read errors as fatal and check for the UBI magic
if the data of a block could be recovered using ECC or similar.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-24 22:24:21 +02:00
Mathias Kresin fdf6760cda kernel: improve ubi auto attach code readability
Move the put_mtd_device() called on multiple error conditions to a goto
label to use it later for more error conditions.

The early return on failed open of the mtd device and mismatching mtd
type allows to get rid of one level of indentation. By jumping to the
cleanup code, a refcount bug is fixed for the wrong flash type condition.

While at it, make clear that we only check for the UBI magic if the read
from flash was successful.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-24 22:24:21 +02:00
John Crispin 1e48e56c50 ipq40xx: drop bus driver, its a no-op and only does lots of alloc/free
Signed-off-by: John Crispin <john@phrozen.org>
2018-07-24 10:50:13 +02:00
Felix Fietkau 7ad20678e5 kernel: backport a change to 4.9 which disables overly aggressive warnings on gcc 8
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-22 17:16:35 +02:00
Felix Fietkau c527d0ec18 kernel: backport fixes for GCC 8 errors in syscall definitions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-22 17:16:30 +02:00
Rosen Penev e22cc57593 ipq806x: dts: Remove device_type = "ethernet-phy"
device_type is deprecated. Upstream doesn't seem to like it either.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-07-19 18:58:24 +02:00
Christian Lamparter 9b47aa93c7 apm821xx: unify My Book Live Single + Duo images
By takimata:
"Come to think of it, an MBL Single board boots up just fine on an
MBL Duo image, and the MBL Single board identifies completely
identical to the MBL Duo
(Board: Apollo-3G - APM82181 Board, 2*SATA, 1*USB).
I wonder if there is any downside to just using the MBL Duo firmware
on a MBL Single. I wonder if the two firmwares could even be unified."

<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/9>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-07-19 18:58:24 +02:00
Thibaut VARÈNE c4f09fc9f8 ramips: define common MikroTik RouterBOARD image recipe
All these devices share the exact same image format.

The usb3 kmod is added for the rbm11g, as the rbm11g has a mini-pcie
slot like its bigger sibling. The usb kmod is necessary for
usb-over-pcie support, which is mandatory for a lot of LTE modules.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-19 18:58:24 +02:00
Johann Neuhauser 02d53e6a21 lantiq: add support for FritzBox 7312
The FritzBox 7312 is also known as 1&1 WLAN-MODEM. The device is almost
the same as FB7330, but only one ETH-Port and no USB.

Hardware
SoC: Lantiq Xway ARX188 PSB 50812 EL
RAM: 64MB DDR1 (Zentel A4S12D40FTP-G5)
Ethernet: Atheros 8030
Wireless: Atheros AR9227 b/g/n 2x2
DSL: Lantiq ADSL2+
DECT: Dialog SC14441
Buttons: WiFi, DECT
LEDs: Power/DSL, Fon, DECT, WLAN, Info

LEDs
Power: GPIO#44 (active low)
Internet: GPIO#47 (active low)
DECT: GPIO#38 (active low)
WLAN: GPIO#37 (active low)
Info: GPIO#35 (active low)

The Fon LED is labeled as internet in avm gpl sources.

Buttons
WLAN: GPIO#1 (active low)
DECT: GPIO#2 (active low)

Phy
GPIO#03: 25 MHz
GPIO#34: Reset (active low)
GPIO#39: Int
GPIO#42: MII MDIO
GPIO#43: MII MDC

PCIe
GPIO#21: reset (active low)

Installation:

To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1
  ftp> quote REBOOT

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-07-18 19:17:46 +02:00
Johann Neuhauser f2f7802148 lantiq: etop: pass devicetree node to phy driver
Use of_mdiobus_register() to pass the ethernet phy node to the phy
drivers. This is needed for the at8030 phy driver which needs to know
the GPIO which is connected to the ar8030 reset pin.

This driver expects a child in gsw/etop node named "mdio-bus", which has
the ethernet phys defined:

&gsw {
	phy-mode = "rmii";
	phy-handle = <&phy0>;
	mtd-mac-address = <&ath9k_cal 0xa91>;
	mtd-mac-address-increment = <(-2)>;

	mdio-bus {
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0>;

		phy0: ethernet-phy@0 {
			reg = <0>;
			reset-gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
		};
	};
};

Fallback to mdiobus_register() if no mdio-bus child node exists. This
way we don't need to touch all xway dts files, for which we don't know
the actual address on the mdio bus.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-07-18 19:17:46 +02:00
Aleksandr V. Piskunov 290c54473e ath79: fix TP-Link Archer C7 v2 wlan1 MAC address
The mac address for the 2.4 wireless need to be decremented by one.

Correct MAC adress increments for this board are:
wlan0 (5GHz)   : -2
wlan1 (2.4GHz) : -1
eth1  (LAN)    :  0
eth0  (WAN)    :  1

Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
2018-07-18 19:17:46 +02:00
Jo-Philipp Wich 8194f9ef4a mediatek: fix parallel build issues in image build code
Drop the parallel-unsafe custom Build/dtb macro and use the .dtb artifacts
produced by the generic image build code.

Also remove unused .dtb references in the mt7623 subtarget.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-07-17 14:40:04 +02:00
Kin Chan 18b87b10a9 ar71xx: Move F9K1115v2 under ar71xx tiny target
F9K1115v2 has a kernel partition size of 1408 kB.

Since kernel 4.9.x+ the kernel image for this device compiled had exceeded
the kernel partition size limit and thus failing size check.

The kernel image generated for this device
under ar71xx tiny target is 1329.67 kB < 1408 kB.

Signed-off-by: Kin Chan <kcchan1@outlook.com>
2018-07-16 15:12:19 +02:00
Chuanhong Guo c9c4b2116c ramips: Use dts alias based status led
Also fix several typos in led node name.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-16 15:12:18 +02:00
Thibaut VARÈNE c2d2647c09 ar71xx: add support for MikroTik RB931-2nD
This patch adds support for the MikroTik RB931-2nD (hAP mini):
https://mikrotik.com/product/RB931-2nD

Specifications:
  * SoC: Qualcomm QCA9533 (650MHz)
  * RAM: 32MiB
  * Storage: 16MiB SPI NOR flash
  * Ethernet: 3x100M
  * Wireless: QCA9533 built-in, dual-chain 802.11b/g/n

Installation:

1. Setup a DHCP/BOOTP Server with the following parameters:
   * DHCP-Option 66 (TFTP server name): pointing to a local TFTP
     server within the same subnet of the DHCP range
   * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
     of the to be booted image. The usable intramfs files are:
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
       - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin

2. Press the reset button on the board and keep that pressed.

3. Connect the board to your local network via its Internet port.

4. Release the button after the LEDs on the board are turned off.
   Now the board should load and start the initramfs image from
   the TFTP server.

5. Now connect the board via either of its LAN ports (2 or 3).

6. Upload the sysupgrade image to the board with scp:
     $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin

7. Log in to the running system listening on 192.168.1.1 via ssh
   as root (without password):
     $ ssh root@192.168.1.1

8. Flash the uploaded firmware file from the ssh session via the
   sysupgrade command:
     root@OpenWrt:~# sysupgrade /tmp/fw.bin

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-16 15:12:17 +02:00
Andrius Štikonas d591260407 brcm63xx: initial support for Sky SR102 router
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
SOC: 	    BCM63168 (BMIPS4350 V8.0 @400MHz)
Flash size: 16 MiB
RAM size:   128 MiB

Heavily based on patch for OpenWRT Chaos Chalmer.
Original patch and more info can be found at:
https://openwrt.org/toh/sky/sr102

Known issues:
 - Wireless and ADSL modem are not working.

Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
2018-07-16 15:12:08 +02:00
Christian Lamparter c3f9a1ac0e apm821xx: attempt to fix sata access freezes
The original vendor's driver programmed the dma controller's
AHB HPROT values to enable bufferable, privileged mode. This
along with the "same priorty for both channels" could very
well fix the freezes that have been reported on the forum by
@ticerex and @takimata.

<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/46>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-07-16 15:10:21 +02:00
Christian Lamparter 12b80f1cab apm821xx: fix usb-otg on 4.14
Starting with 4.14, the "amcc,dwc-otg" needs to be used
in order to get the usb-otg to work.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-07-16 08:42:21 +02:00
Felix Fietkau 18533ff415 kernel: backport page fragment API changes from 4.10+ to 4.9
mt76 now relies on this API

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-14 11:39:00 +02:00
Felix Fietkau 2601e34fad ramips: ethernet: disable fraglist support
The code has some remaining issues that cause ethernet hangs, so
disable it for now until we can get it fixed

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-14 08:32:39 +02:00
Felix Fietkau 0c285bd081 ramips: ethernet: use own page_frag_cache
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragment.
This can happen if the ethernet driver grabs one or two fragments for rx
ring refill, while other drivers use (and free up) the remaining
fragments. The 32 KiB higher-order page can only be freed once all users
have freed their fragments, which only happens after the rings of all
drivers holding the fragments have wrapped around.

Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-12 18:43:53 +02:00
Felix Fietkau 01df4a2565 ramips: ethernet: use skb_free_frag to free fragments
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-12 18:43:53 +02:00
Peter Lundkvist 2eeb4b78c6 ramips: TP-Link TL-WR902AC v3: add missing wps button
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
2018-07-12 18:15:33 +02:00
Peter Lundkvist 33321ebefa ramips: TP-Link TL-WR902AC v3: don't build factory image
The line that produces factory image was accidentally left by me while
testing before inital commit.

I came to the conclusion that flashing from OEM firmware does not work
(seems to share this behavior with other tplinks based on mt7628).

I have not done any further analysis, as I was unable to open the
case and attach a serial port (too much glue). Maybe i will try once
more.

So the way to do initial flashing (or un-bricking) is to use the
tftp-recover image. It is possible to revert to OEM firmware with tftp
recovery; in this case the first 512 bytes the image file need to be
cut off.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[add explaination provided via mail as commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-12 18:15:33 +02:00
Alex Maclean 11d6547455 config: extend small_flash feature
Extend the small_flash feature to disable swap, core dumps, and
kernel debug info, and change the squashfs block size to 1024KiB.

Also change squashfs fragment cache to 2 for small_flash to ease memory
usage.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-07-12 18:15:33 +02:00
Mathias Kresin cf7154db07 kernel: only optimized for size if small_flash
Add a new config option to allow to select the default compile
optimization level for the kernel.

Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.

Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.

Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.

Exceptions to the above are:

  - lantiq, where the optimization for size is only required for the
    xway_legacy subtarget but was set for the whole target
  - mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
    plenty of space and an optimization for size doesn't make much sense
  - rb532, which has 128MByte flash

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-12 18:15:32 +02:00
Mathias Kresin 621fa91a82 ar71xx: move boards to tiny subtarget
Move boards to the tiny subtarget which break the build if the kernel is
set to "Optimize for performance".

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-12 18:15:19 +02:00
Evgeniy Didin 12915b105a arc: Update variables substitutions in u-boot env files
In the latest version of u-boot (2018.05) there was a swith to
Hush shell for ARC AXS10x boards(arc770/archs38):
commit 9249d74781e1 ("ARC: AXS10x: Enable hush shell").
In Hush shell using "$()" to declare envitonment variables is forbidden,
instead of this "${}" need to be used.

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
2018-07-12 10:24:31 +02:00
Kristian Evensen d238c7f995 mediatek: Fix memory node for U7623
The changed applied to BananaPi R2 in upstream commit c0b0d540db1a,
which was backported to 4.14 in 4.14.53, is also required for the U7623.
Without updating the memory node, the board refuses to boot.

Fixes: d0839e020d ("kernel: bump 4.14 to 4.14.53")

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2018-07-12 08:53:02 +02:00
Felix Fietkau 33553a11ab ramips: clean up and fix MT7621 NAND driver issues
- remove misaligned custom buffer allocation in the NAND driver
- remove broken bounce buffer implementation for 16-byte align

Let the MTD core take care of both

Fixes messages like these:
[  102.820541] Data buffer not 16 bytes aligned: 87daf08c

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-11 20:59:44 +02:00
Felix Fietkau 21ee8ce9b5 kernel: replace bridge port isolate hack with upstream patch backport on 4.14
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-11 20:59:05 +02:00
Felix Fietkau 41a1c1af4b kernel: adjust bridge port isolate patch to match upstream attribute naming
Newer kernels have a patch that implements compatible functionality
directly. Adjust the attribute of our own patch in preparation for
dropping it later

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-11 20:59:05 +02:00
Koen Vandeputte ba2b0f0ac6 kernel: bump 4.14 to 4.14.54
Rereshed all patches

Reworked patches to match upstream:
335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-11 16:02:24 +02:00
Rafał Miłecki 7ddba08d87 kernel: bcm47xxpart: fix getting user-space data partition name
Partition name is picked by a parser_trx_data_part_name(). It has to
get correct partition offset (taking care of bad blocks) to work
properly.

This fixes UBI support for devices that have kernel flashed on partition
with a bad block.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-10 14:05:02 +02:00
David Bauer 6476148034 ath79: add support for OCEDO Raccoon
This commit adds support for the OCEDO Raccoon

SOC:	Atheros AR9344
RAM:    128MB
FLASH:  16MiB
WLAN1:  AR9344 2.4 GHz 802.11bgn 2x2
WLAN2:  AR9382 5 GHz 802.11an 2x2
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

	NOTE: The U-Boot won't boot with the serial attached.
	Boot the device without serial attached and attach it
	after 3 seconds.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'raccoon-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'raccoon-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-07-08 00:04:27 +02:00
Hauke Mehrtens da6c09eff4 kernel: move CONFIG_USB_MTU3 to generic config
CONFIG_USB_MTU3 is not visible for the mediatek target by default, but
only when CONFIG_USB_GADGET is set. This will config option will be
remove with when running "make kernel_oldconfig", move this option to
the generic config to prevent this.

This fixes the build of the mt7623 subtarget of the mediatek target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-07-07 23:53:04 +02:00
Hauke Mehrtens 29fa9ac559 kernel: disable some DRM_PANEL config options
The modules should not be build by default.
This fixes the build of the zynq target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-07-07 23:53:04 +02:00
Lucian Cristian 2d268c0710 ath79: disable unused drivers for tiny target
Shrink the tiny kernel by moving all switch and ethernet phy drivers to
the generic kernel config instead of the target kernel config.

All boards in the tiny and nand target are either ar7240 or ar9331 based,
which don't support external xMII and therefore no external ethernet phy
can be connected. None of the boards uses a realtek switch either.

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-07 21:07:40 +02:00
Lucian Cristian 80e3a16fda ath79: optimize ath79 tiny target for size
the speed impact on tiny target is minimal and worth the size gained

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-07 21:07:40 +02:00
Christoph Krapp e420b7b5c5 ath79: add support for UniFi AC-Mesh Pro
The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except
USB support.
Furthermore for setting parameters like antenna gain it is helpful to
know the exact device variant.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-07-07 21:07:40 +02:00
Ademar Arvati Filho 16d6a63f85 ramips: add support for Blueendless Kimax U35WF
Blueendless Kimax U35WF is a 3,5" HDD Enclosure with Wi-Fi and Ethernet

Patch rewritten from: https://forum.openwrt.org/viewtopic.php?id=66908
Based on: https://github.com/lede-project/source/pull/965

Specification:
- SoC: MediaTek MT7620N
- CPU/Speed: 580 MHz
- Flash-Chip: KH25L12835F Spi Flash
- Flash size: 16 MiB
- RAM: 64 MiB
- LAN: 1x 100 Mbps Ethernet
- WiFi SoC-integrated: 802.11bgn
- 1x USB 2.0
- UART: for serial console

Installation:
1. Download sysupgrade.bin
2. Open vendor web interface
3. Choose to upgrade firmware
3. After reboot connect via ethernet at 192.168.1.1

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-07 21:07:40 +02:00
Mathias Kresin a28d686fb6 ar71xx: factor out safe loader image build code
Add a template for safeloader images and include it instead of
overwriting variables defined in the common tp-link build commands.

Split the existing tp-link templates to proper implement the safeloader
template.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-07 21:07:40 +02:00
Mathias Kresin b908c82f49 ar71xx: drop unnecessary LOADER_TYPE variables
Drop the LOADER_TYPE variables in case no loader is used at all or move
the variable to devices which are using a loader.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-07 21:07:40 +02:00
Mathias Kresin a0ec632f8d ar71xx: get rid of copy-file
Use the provided image build variables to point the kernel-bin build
command to the kernel we are interested in.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-07 21:07:40 +02:00
Mathias Kresin 5260c1003c ar71xx: mikrotik: cleanup nand image build code
Use the LOADER_TYPE variable to specify that we need the elf preloader
and append the loader via the corresponding build recipe. It allows to
enable initramfs images again for mikrotik NAND images, which caused a
build error before.

Add the minor header only to the kernel of the sysupgrade images, as it
is only required for the bootloader to find the kernel on flash.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-07 21:07:40 +02:00
INAGAKI Hiroshi 0b83a23560 ramips: add support for I-O DATA WN-AX1167GR
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 115200 bps (U-Boot, OpenWrt)

Stock firmware:

In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.

(excerpt from dmesg):

MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"

The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.

If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.

(example):

## Booting image at bc800000 ...
Bad Magic Number,FFFFFFFF
Boot from KERNEL 1  !!
## Booting image at bc060000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.50
   Image Type:   MIPS Linux kernel Image (lzma compressed)
   Data Size:    1865917 Bytes = 1.8 MB
   Load Address: 80001000
   Entry Point:  80001000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!

Starting kernel ...

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-07-07 21:07:40 +02:00
Daniel Engberg 3accbc6aac sunxi: Enable SD block devices
USB storage support is however SCSI Disk block device support isn't
meaning that connected devices wont enumerate.
Enable CONFIG_BLK_DEV_SD by default to fix it.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2018-07-07 18:19:39 +02:00
Alexandru Ardelean 7de50d1917 brcm2708: platform.sh: fix tar directory directive
BusyBox's `tar` command does not support the `--directory` directive, which
is essentially `-C` in short-form option.
BusyBox's `tar` command supports `-C`.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
2018-07-07 18:19:39 +02:00
Luis Araneda 8f60c3d571 kernel: remove DEVMEM and DEVKMEM from target's config
These options are handled by generic configuration

Targets that need these options should select KERNEL_DEVMEM
and/or KERNEL_DEVKMEM options on OpenWRT's config

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-07-07 18:19:39 +02:00
Tim Small e97aaf483c WDR4900v1 remove dt node for absent hw crypto.
The WDR4900v1 uses the P1040 SoC, so the device tree pulls in the
definition for the related P1010 SoC.  However, the P1040 lacks the
CAAM/SEC4 hardware crypto accelerator which the P1010 device tree
defines.  If left defined, this causes the CAAM drivers (if present) to
attempt to use the non-existent device, making various crypto-related
operations (e.g. macsec and ipsec) fail.

This commit overrides the incorrect dt node definition in the included
file.

See also:
 - https://bugs.openwrt.org/index.php?do=details&task_id=1262
 - https://community.nxp.com/thread/338432#comment-474107

Signed-off-by: Tim Small <tim@seoss.co.uk>
2018-07-07 18:19:39 +02:00
Antti Seppälä 9f451ec698 kernel: usb: dwc2 DMA alignment fixes
Add two patches submitted for upstream review that significantly improve
the dwc2 driver on openwrt from kernel stability and performance
perspectives.

Fixes: FS#1367

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
2018-07-07 18:19:39 +02:00
Felix Fietkau c3bdb89e61 kernel: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-07 14:53:26 +02:00
Koen Vandeputte d0839e020d kernel: bump 4.14 to 4.14.53
Refreshed all patches

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-04 14:16:37 +02:00
Koen Vandeputte 01ca20cdfd kernel: bump 4.9 to 4.9.111
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-04 14:16:37 +02:00
Christoph Krapp 8722c52b41 ath79: remove bs-partition ro-flag for UniFi AC devices
This removes the read-only flag from the bs (bootselect) partition
on UniFi AC devices. This allows to correct the indicator from which
partition the device is booting its kernel from.

See also:
 - freifunk-gluon/gluon#1301
 - https://bugs.lede-project.org/index.php?do=details&task_id=662

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-07-04 01:20:03 +02:00
Aleksandr V. Piskunov 63c9081c77 ath79: swap TP-Link Archer C7 v2 USB port LED and GPIO names
TP-Link Archer C7 v2 USB port LED and GPIO names are in incorrect order,
i.e. in order to match actual user visible labels, usb1 should be usb2,
and vice versa.
This patch swaps LED and GPIO power control node names.

Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
2018-07-04 01:20:03 +02:00
Mathias Kresin 31aa62c5ec ath79: drop mv88e6063 switch driver
Due do a missing KCONFIG isn't selectable nor enabled in the target
kernel config. Drop it for now and enable/add the driver at the time it
is required.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-04 01:20:02 +02:00
Aleksandr V. Piskunov 36fea5a7b9 ipq806x: fix numbering for Netgear R7800 LAN ports
Netgear R7800 switch LAN ports are numbered backwards in LuCI,
i.e. numbering is not corresponding to the actual physical port labels,
patch fixes that.

Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[merged with existing board using the same config]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-07-04 01:20:02 +02:00
Romain MARIADASSOU ce31bdc20c ramips: add support for TL-WA801ND v5
Specification:

- System-On-Chip: MediaTek MT7628NN
- CPU/Speed: 580 MHz
- Flash-Chip: ELM Technology GD25Q64
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn

Currently the only method to install openwrt for the first time is via
TFTP recovery. After first install you can use regular updates.

Flash instructions:

1) To flash the recovery image, start a TFTP server with IP address
   192.168.0.66 and serve the recovery image named tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS and Reset
   button and power it up. Keep pressing the WPS/Reset button for
   10 seconds or until the lock LED is lighting up.
   It will try to download the recovery image and flash it.

It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
2018-07-04 01:20:02 +02:00
Maxim Anisimov 7d07bc96b7 ramips: add support for ZyXEL Keenetic Extra II
Specification:
- System-On-Chip: MT7628N/N
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (57600 8n1)
- Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn
- Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac
- USB: Yes 1 x 2.0
- 4x LED, 3x button

The device supports dual boot mode. So we use only first half of flash.

Flash instruction:

The only way to flash OpenWrt image is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin"
   to "kextra2_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-07-04 01:20:02 +02:00
Maxim Anisimov 9e2c28472c ramips: move zyimage define to common Makefile
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-07-04 01:20:02 +02:00
Tobias Schramm faf64056dd ramips: add support for MikroTik RouterBOARD RBM11g
This commit adds support for the MikroTik RouterBOARD RBM11g.

=Hardware=

The RBM11g is a mt7621 based device featuring one GbE port and one
miniPCIe slot with a sim card socket and USB 2.0.

==Switch==

The single onboard Ethernet port is connected the CPU directly.
The internal switch of the mt7621 SoC is disabled.

==Flash==

The device has one spi nor flash chip. It is a 128 Mbit winbond 25Q128FVS
connected to CS0.

==PCIe==

The board features a single miniPCIe slot. It has a dedicated mini SIM
socket and a USB 2.0 port. Power to the miniPCIe slot is controlled via
GPIO9.

==USB==

There are no external USB ports.

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack (center-positive). The input voltage range is 11-32 V.

==Serial port==

The device does have an onboard UART on an unpopulated header next to the
flash chip:

GND: pin 2
 TX: pin 7
 RX: pin 6

Settings: 115200, 8N1

See below illustration for positioning of the header.

0 = screw hole
* = some pin
T = TX  pin
R = RX  pin
G = GND pin

Pinout:
+---------------
|O
|             __
|            /  \
|            \__/
|
|
|
|               +---+
|               |RAM|
| +--+          |   |
| |**|  <- unpopulated header with UART
| |*T|          +---+
| |R*|        +--------+
| |**|        |        |
| |G*|        |  CPU   |
| +--+        |        |
|    +--+     |        |
|    |  |     +--------+
|    +--+  <- flash chip
|O
|       +-----+
|       |     |
|+--+   |     |
||  |   |     |
+---------------------

=Installation=

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM11G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" in the
output directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the
created license file.**

When rebooted the board will try booting via ethernet first. If your
board does not boot via ethernet automatically you will have to attach
to the serial port and set ethernet as boot device within RouterBOOT.

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin"
   initramfs image
2. Connect to ethernet port on board
3. Power on the board
4. Wait for OpenWrt to boot

Right now OpenWrt will be running with a SSH server listening. Now
OpenWrt must be flashed to the devices flash:

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
   to the device using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"

Once the flashing completes the board will reboot. Disconnect from the
devices ethernet port or stop the DHCP/TFTP server to prevent the device
from booting via ethernet again.
The device should now boot straight to OpenWrt.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-07-04 01:20:02 +02:00
Michael Kuron d0b89e48d7 lantiq: enlarge AVM Fritz!Box 3370 flash
Increase the available flash memory size in AVM Fritz!Box 3370 by
incorporating the unused extra partitions located after the ubi partition.

Note that users upgrading from a previous OpenWRT version need to
re-install from the boot loader to pick up the new partition layout.

Available flash space for rootfs+overlay increases from 48MB to 124MB.

Reverting to the OEM firmware is still possible (via the recovery utility
provided by AVM) as the OEM firmware appears to reformat the config and
nand-filesystem partitions upon first boot if necessary. The
reserved-kernel and reserved-filesystem partitions are overwritten by the
OEM firmware when installing an update, so their contents do not matter.

Boot loader and device-specific information (MAC addresses, calibration
data, etc.) are not located in NAND flash and remain unharmed by this
changed.

Tested with OEM firmware 06.54 on device with HWRevision 5 and Micron
flash chip.

Signed-off-by: Michael Kuron <m.kuron@gmx.de>
2018-07-04 01:20:02 +02:00
Mathias Kresin f72605f70e lantiq: backport stp-xway get callback implementation
To keep the status of a LED connected to the stp during boot, the get
callback is required. If the callback is missing and the LED default
state is set to keep in the devicetree, the gpio led driver errors out
during load.

Fixes: FS#1620

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-04 01:20:01 +02:00
Mathias Kresin eccde89aa4 kernel: fix AT8032 PHY phy id mask
Don't mask bit 4 of the AT8022 phy id. If bit 4 of the AT8022 phy id
(0x004dd023) is masked, it will match the phy id of the AR8327 switch
(0x004dd033) as well.

It results in applied at803x driver settings/callbacks, which will at
least limit the AR8327 phys to 100MBit operation instead of the possible
1000MBit.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-04 01:19:05 +02:00
Kevin Darbyshire-Bryant 3698b34a00 kernel: gen_stats: Fix netlink stats dumping in the presence of padding
Backport hot off the press upstream netlink patch.  Fixes stats display
from CAKE qdisc on MIPS allowing us to bump CAKE to latest version.

The gen_stats facility will add a header for the toplevel nlattr of type
TCA_STATS2 that contains all stats added by qdisc callbacks. A reference
to this header is stored in the gnet_dump struct, and when all the
per-qdisc callbacks have finished adding their stats, the length of the
containing header will be adjusted to the right value.

However, on architectures that need padding (i.e., that don't set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added
before the stats, which means that the stored pointer will point to the
padding, and so when the header is fixed up, the result is just a very
big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS
struct, this problem has been mostly invisible, but we exposed it with
the netlink attribute-based statistics in CAKE.

Fix the issue by fixing up the stored pointer if it points to a padding
nlattr.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-07-03 11:40:18 +01:00
Felix Fietkau 09b6755946 ramips: limit dictionary size for lzma compression
In some cases, recent builds fail to boot from flash with at least some
MT7621 based devices. The error message is:
"LZMA ERROR 1 - must RESET board to recover"
Booting the same kernel via TFTP works for some reason.

Through testing I figured out that limiting the LZMA dictionary size
seems to prevent these errors

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-03 11:18:39 +02:00
Luis Araneda efa112261b zynq: remove config options handled by generic
The options are now handled for all targets by
the generic configuration

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-07-02 07:12:48 +02:00
Peter Lundkvist 781ad46206 ath79: add support for TP-Link RE450 v2
TP-Link RE450 v2 is a dual band router/range-extender
based on Qualcomm/Atheros QCA9563 + QCA9880.

Specification:

- 775 MHz CPU
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 1x 10/100/1000 Mbps Ethernet (AR8033 PHY)
- 7x LED, 4x button
- UART header on PCB (needs unmounted R64 & R69 0201 resistors/jumpers)

Flash instruction:
Apply factory image in OEM firmware web-gui.

U-Boot does not seem to have any recovery functions, so
debricking requires connection via UART.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
2018-07-02 07:05:33 +02:00
Koen Vandeputte f4ac88b509 kernel: bump 4.14 to 4.14.52
Refreshed all patches

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-02 07:04:48 +02:00
Koen Vandeputte 8e622aae58 kernel: bump 4.9 to 4.9.110
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-02 07:04:34 +02:00
Rocco Folino 4ff019722c ath79: port TP-Link TL-WR741ND v4 and TL-WR740ND v4
This patch ports the TP-Link TL-WR741ND v4 and TL-WR740ND v4 to the
ath79 target.

Because the two devices share the same hw layout, this patch adds a common
.dtsi which is included by the two .dts.

Signed-off-by: Rocco Folino <rocco@folino.io>
2018-07-02 07:03:21 +02:00
Rocco Folino 9b575288eb ath79: add pinmux to ar9330
This patch adds the pinmux support to the ar9330 used to disable the
JTAG or to enable switch LEDs

Signed-off-by: Rocco Folino <rocco@folino.io>
2018-07-02 07:00:20 +02:00
Lev 3d6f57f3c6 ramips: fix wizfi630a swapped lan/wan port
The order of the Ethernet ports were mixed up.
This commit fixes the order to be aligned with the physical layout.

Signed-off-by: Lev <leventelist@gmail.com>
2018-07-02 06:59:31 +02:00
Adrian Schmutzler 4456dd4660 ath79: add support for Unifi AC Mesh
The Unifi AC Mesh is equivalent to the Unifi AC Lite. However,
for setting certain parameters with the flashed device it is
helpful that the devices know their variant (e.g. automatically
setting antenna gain for the different antennas in Lite and Mesh).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-28 20:31:48 +02:00
Dmytro Smyrnov 40218a2632 ath79: add support for more AR7241 TP-Link boards
Its common AP99(AR7241) platform with following devices:

  TP-Link TL-WR841N/ND v7 (SoC AR7241 / Wifi AR9287 / without USB)
  TP-Link TL-MR3220 v1 (SoC AR7241 / Wifi AR9285 / USB support)
  TP-Link TL-MR3420 v1 (SoC AR7241 / Wifi AR9287 / USB support)

Signed-off-by: Dmytro Smyrnov <dioptimizer@hotmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 20:31:47 +02:00
Lucian Cristian 25070f7106 ath79: small wr1043nd-v4 fixes
- fix sysupgrade check
- move usb to v4 dts because v5 doesn't have it
- make wan mac address behave like ar71xx target
- add orange wan led support, it can be userspace activated like:

  on:
  echo default-on > /sys/class/leds/tp-link\:orange\:wan/trigger

  off:
  echo none > /sys/class/leds/tp-link\:orange\:wan/trigger

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-28 20:31:03 +02:00
Lucian Cristian 7dd3d7e1d3 ath79: add support for Ubiquiti UniFi AC-Pro
rework the dts to a common unifi-ac dtsi
pro network is connected via phy0 and has usb ports
lite network is connected via phy4 without usb ports

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-28 18:39:57 +02:00
Adrian Schmutzler 56fddc2577 ath79: sync naming of Ubiquiti devices
Use a Unifi AC Lite board-/image name consistent with other Ubiquiti
devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-28 18:39:57 +02:00
Chuanhong Guo c463320812 ath79: Remove all memory nodes defined in dts
This target can automatically detect the correct memory size and we've
been using it for long in ar71xx.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-06-28 18:39:57 +02:00
Mathias Kresin a570933999 treewide: gpio-export: add error handling
Check if the GPIO is valid (or set at all). If no GPIO is set in the
devicetree, a gpiolib related kernel warning + stacktrace is shown during
boot and gpio-export reports GPIOs as exported albeit none really is.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 18:39:57 +02:00
Mathias Kresin 750e4b62b1 ipq806x: drop gpio export patch
The hack isn't used by any board.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 18:39:57 +02:00
Stefan Lippers-Hollmann 7c7ca66109 ipq806x: switch the NBG6817 wlan LEDs from amber to white
The original device support patch configured the amber wlan LEDs (which
are meant as error indicator by the OEM) controlled by the SOC's GPIO
as wlan traffic indicators, as the correct white wlan LEDs are
connected to GPIOs controlled by the QCA9984/ ath10k wlan cards were
not accessible. The recent addition of GPIO/ LED support to ath10k now
makes it possible to use the correct white LEDs instead - and
"mac80211: ath10k: use tpt LED trigger by default" also enables them by
default. While both LEDs are independent of each other (two separate
LEDs sharing one light tunnel), triggering both on wlan traffic is not
the intended behaviour (bright yellow light).

Tested on the ZyXEL NBG6817.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-06-28 18:39:57 +02:00
Andrey Jr. Melnikov 19c7e950af ramips: move mt7620n i2c_pins definition to right place
Move to i2c pins pinmux node to the pinctrl node.

Fixes: a0685deec4 ("ramips: Add i2c support for mt7620n")

Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
[fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 18:39:57 +02:00
Hannu Nyman 7b74b40fe9 ipq806x: remove "firmware" partition definition from netgear routers
Remove the "firmware" partition definition from the DTS of R7800
to fix sysupgrade.

Commit 4645a6d3 defined CONFIG_MTD_SPLIT_UIMAGE_FW=y for ipq806x
and that causes mtd to misbehave as additional kernel and ubi
partitions are detected from inside the "firmware" partition.
  [    1.111324] 0x000001480000-0x000001880000 : "kernel"
  [    1.121005] 0x000001880000-0x000007900000 : "ubi"
  [    1.283912] 0x000007900000-0x000008000000 : "reserve"
  [    1.296407] 0x000001480000-0x000007900000 : "firmware"
  [    1.468043] no rootfs found after FIT image in "firmware"
  [    2.426860] 2 uimage-fw partitions found on MTD device firmware
  [    2.426931] 0x000001480000-0x000001880000 : "kernel"
  [    2.440420] 0x000001880000-0x000007900000 : "ubi"

Both kernel and ubi are already defined in DTS, so this duplication
leads into errors in sysupgrade:
  Writing from <stdin> to kernel ...
  ubiattach: error!: strtoul: unable to parse the number '6 mtd10'
  ubiattach: error!: bad MTD device number: "6 mtd10"

The partition is defined to same area as kernel+ubi, and is not
needed for sysupgrade anymore. Remove it to fix things.

Only tested for the R7800 but all of them should behave equal.

Fixes: FS#1617

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[squashed commits, add "tested on" note]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-27 22:11:06 +02:00
INAGAKI Hiroshi 0efd0308a0 ramips: add switch port index for I-O DATA WN-GX300GR
WN-GX300GR has 5x RJ45 ports (port 0-4), and these ports are
orderd on the device as follows:
4 3 2 1 0

1-4: lan
0: wan

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-27 08:42:54 +02:00
Lucian Cristian 4ec9763ee9 firmware-utils: tplink-safeloader: switch tl-wr1043nd-v4 to dynamic partitions
Use the new dynamic partition split in tplink-safeloader so we no longer
have to worry about kernel size increases.

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-27 08:42:54 +02:00
Christian Lamparter 82618062cf ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617

Hardware highlights:

SOC:    IPQ4018 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR:    32 MiB Macronix MX25L25635F
ETH:    Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:    1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:  RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS:   Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS

Serial:
	WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
	The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
	pre-soldered. Pinout:
	  1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX

first install / debricking / restore stock:
 0. Have a PC running a tftp-server @ 192.168.1.99/24
 1. connect the PC to any LAN-Ports
 2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
    into the tftp-server root directory and rename it to just "ras.bin".
 3. power-cycle the router and hold down the the WPS button (for 30sek)
 4. Wait (for a long time - the serial console provides some progress
    reports. The u-boot says it best: "Please be patient".
 5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
    flashes fast at the same time. You have to reboot the device and
    it should then come right up.

Installation via Web-UI:
 0. Connect a PC to the powered-on router. It will assign your PC a
    IP-address via DHCP
 1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
 2. Go to the "Expert Mode"
 3. Under "Maintenance", select "Firmware-Upgrade"
 4. Upload the OpenWRT factory image
 5. Wait for the Device to finish.
    It will reboot into OpenWRT without any additional actions needed.

To open the ZyXEL NBG6617:
 0. remove the four rubber feet glued on the backside
 1. remove the four philips screws and pry open the top cover
    (by applying force between the plastic top housing from the
    backside/lan-port side)

Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:

|   Hit any key to stop autoboot:  3

The user is then dropped to a locked shell.

|NBG6617> HELP
|ATEN    x[,y]     set BootExtension Debug Flag (y=password)
|ATSE    x         show the seed of password generator
|ATSH              dump manufacturer related data in ROM
|ATRT    [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO              boot up whole system
|ATUR    x         upgrade RAS image (filename)
|NBG6617>

In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!

First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.

|NBG6617> ATSE NBG6617
|012345678901

This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):

- tool.sh -
ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -

|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711

copy and paste the result into the shell to unlock zloader.

|NBG6617> ATEN 1,0046B0017430

If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.

|NBG6617> ATGU
|NBG6617#

Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-26 08:57:26 +02:00
Sibren Vasse ba74b45476 ath79: add support for TP-Link Archer c7 v2
Signed-off-by: Sibren Vasse <github@sibrenvasse.nl>
2018-06-26 08:57:26 +02:00
Lucian Cristian 2a7e03af37 ath79: add tl-wr2543-v1 support
to switch between wlan leds we need a userspace implementation

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-26 08:57:26 +02:00
Kevin Darbyshire-Bryant 094d49cddf kernel: bump 4.14 to 4.14.51
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Refresh patches.

Remove patch that can be reverse applied:
mvebu/patches-4.14/530-ATA-ahci_mvebu-enable-stop_engine-override.patch
mvebu/patches-4.14/531-ATA-ahci_mvebu-pmp-stop-errata-226.patch

Update patch that no longer applied:
ipq806x/patches-4.14/0035-clk-mux-Split-out-register-accessors-for-reuse.patch

Compiled-tested-for: lantiq, ramips
Run-tested-on: lantiq BT hh5a, ramips MIR3g

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Michael Yartys <michael.yartys@protonmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
2018-06-26 08:57:21 +02:00
Zoltan HERPAI 31c26cece3 ath79: add support for ON Networks N150R
This is a rebranded Netgear WNR612v2, specs are the same.

 - Atheros AR7240 (Python) @400MHz
 - flash 4MB
 - ram 32MB
 - ethernet 10/100: 1xwan + 2xlan (only two)
 - radio AR9285

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-06-26 07:05:44 +02:00
Zoltan HERPAI 51dd8ec62f ath79: add Netgear WNR612 v2
Netgear WNR612 v2:
 - cpu Atheros AR7240 (Python) @400MHz
 - flash 4MB
 - ram 32MB
 - ethernet 10/100: 1xwan + 2xlan (only two)
 - radio AR9285

As there is a rebranded WNR612v2 called ON Networks N150R, add
a dtsi which includes all device support, and add a separate dts
for the device only (with a separate one for the subsequent N150R).

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-06-26 07:05:30 +02:00
Alex Maclean 2f23a0583a ramips: RE350: add rootfs offset to header
Have mktplinkfw fill in the rootfs offset so the firmware splitter can
find it without aligning to erase blocks.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-26 07:04:43 +02:00
Franz Flasch 8375623a06 ramips: add support for TP-Link Archer C2
Specification:

- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond 25Q64BVSIG
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac
- Switch: RTL8367RB Gigabit Switch
- USB: Yes 1 x 2.0

Preparing a TFTP recovery image for initial flashing:

Currently the only method to install openwrt for the first time is via
TFTP download in u-boot. After first install you can use regular updates.
WARNING: This method also overwrites the bootloader partition!

Create a TFTP recovery image:

1) Download a stock TP-Link Firmware file here:
     https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware
2) Extract u-boot from the binary file:
     #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072
3) Now merge the sysupgrade image and the u-boot into one binary:
     #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin

The resulting image can be flashed via TFTP recovery mode.

Flash instructions:

1) To flash the recovery image, start a TFTP server from IP address
   192.168.0.66 and serve the recovery image named
   ArcherC2V1_tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS/Reset button
   and power it up. Keep pressing the WPS/Reset button for 10 seconds.
   It will try to download the recovery image and flash it.

It can take up to 20-25 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Franz Flasch abb7524683 ramips: fix ZyXEL Keenetic Viva switch config
The rtl8367b driver never supported a mdio property and it is quite
likely that the switch never worked for the board.

Use the mii-bus property instead to manage the switch via a mdio bus.

Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Franz Flasch d4ac26ec49 kernel: rtl8366-smi: add Realtek switch management via mii-bus
Current version of rtl8366-smi module only supports Realtek switch
managment via two gpio lines. This adds Realtek switch
management via mii_bus. Tested on a Tp-link Archer C2 v1 (Mediatek
SoC mt7620a based)

dts-file configuration should look like this:

rtl8367rb {
	compatible = "realtek,rtl8367b";
	realtek,extif1 = <1 0 1 1 1 1 1 1 2>;
	mii-bus = <&mdio0>;
};

&ethernet {
	status = "okay";
	mtd-mac-address = <&rom 0xf100>;
	pinctrl-names = "default";
	pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;

	port@5 {
		status = "okay";
		mediatek,fixed-link = <1000 1 1 1>;
		phy-mode = "rgmii";
	};

	mdio0: mdio-bus {
		status = "okay";
	};
};

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Mathias Kresin f9e7f19334 kernel: rtl8367b: drop redundant compatible
Remove the compatible without vendor prefix. It is formal wrong and not
used in the tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-25 20:52:18 +02:00
Adrian Schmutzler 5c5bf8b865
ar71xx: Add support for TP-Link CPE210 v2
This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-23 16:06:31 +02:00
Adrian Schmutzler 2524febf79
ar71xx: Add TP-Link Pharos v2 board detection
Add support for detecting TP-Link Pharos v2 boards.
They use different format in product-info partition than v1 boards.

Code was written mostly by Alexander Couzens <lynxis@fe80.eu>

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-23 16:02:01 +02:00
Axel Neumann 65c05301c2 Re-enable arbitrary IPv6 addresses as outer ip4-in-ip6 tunnel source address
The 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch kernel patches
break the possibility for using an ip4ip6 tunnel interface as a fall
back interface accepting ip4-in-ip6 tunneled packets from any remote
address. This works out of the box with any normal (non-666-patched)
kernel and can be configured by setting up an 'ip -6 tunnel' with type
'any' or 'ip4ip6' and a remote address of '::'.

The misbehavior comes with line 290 the patch which discards all packets
that do not show the expected saddr, even if no single fmr rule was
defined and despite the validity of the saddr was already approved earlier.

Signed-off-by: Axel Neumann <neumann@cgws.de>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
2018-06-23 09:47:05 +02:00
Kristian Evensen 4def81f30f mediatek: Add support for the UniElec U7623-02
This commit adds support for the MT7623A-based UniElec U7623-02 router,
with eMMC storage and 512MB RAM. The router can be delivered with NAND
Flash and more memory, but I only have access to the one configuration.
The DTS is structured in such a way that adding support for
more/different storage/memory should be straight forward.

The device has the following specifications:

* MT7623A (quad-core, 1.3 GHz)
* 512MB RAM (DDR3)
* 8GB storage (eMMC 4.5)
* 2x normal miniPCIe slots
* 1x miniPCIe slot that is connected via an internal USB OTG port
* 5x 1Gbps Ethernet (MT7530 switch)
* 1x UART header
* 1x USB 3.0 port
* 1x SATA 3.0
* 1x 40P*0.5mm FPC for MIPI LCD
* 1x SIM slot
* 12x LEDs (2 GPIO controlled)
* 1x reset button
* 1x DC jack for main power (12V)

The following has been tested and is working:
* Ethernet switch
* miniPCIe slots (tested with Wi-Fi cards)
* USB 3.0 port
* sysupgrade
* reset button

Not working:
* The miniPCIe connected via USB OTG. For the port to work, some MUSB
glue must be added. I am currently in the process of porting the glue
from the vendor SDK.

Not tested:
* SATA 3.0
* MIPI LCD

Installation:

The board ships with u-boot, and the first installation needs to be done
via the bootloader using tftp. Step number one is to update the MBR of
the eMMC, as the one that ships with the device is broken. Since the
device can ship with different storage sizes, I will not provide the
exact steps for creating a valid MBR. However, I have made some
assumptions about the disk layout - there must be one 8MB recovery
partition (FAT32) and a partition for the rootfs (Linux).

The board loads the kernel from block 0xA00 (2560) and I have reserved
32MB for the kernel (65536 blocks). I have aligned the partitions on the
erase block size (4096 byte), so the recovery partition must start on
block 69632 and end on 86016 (16385 sectors). The rootfs is assumed to
start on sector 90112.

In order to install the mbr, you run the following commands from the
u-boot command line:

* tftpboot ${loadaddr} <name of mbr file>
* mmc device 0
* mmc write ${loadaddr} 0x00 1

Run the following commands to install + boot OpenWRT:

* tftpboot ${loadaddr} openwrt-mediatek-mt7623-7623a-unielec-u7623-02-emmc-512m-squashfs-sysupgrade-emmc.bin.gz
* run boot_wr_img
* run boot_rd_img
* bootm

Recovery:

In order to recover the router, you need to follow the installation
steps above (no need to replace MBR).

Notes:

* F2FS is used as the overlay filesystem.

* The device does not ship with any valid MAC address, so a random
address has to be generated. As a work-around, I write the initial
random MAC to a file on the recovery partition. The MAC of the WAN
interface is set to the MAC-address contained in this file on each boot,
and the address of the LAN-interfaces are WAN + 1. The MAC file is kept
across sysupgrade/firstboot.

My approach is slightly different than what the stock image does. The
first fives bytes of the MAC addresses in the stock image are static,
and then the last byte is random. I believe it is better to create fully
random MAC addresses.

* In order to support the miniPCIe-slots, I needed to add missing
pcie-nodes to mt7623.dtsi. The nodes are just c&p from the upstream
dtsi.

* One of the USB3.0 phys (u3phy2) on the board can be used as either USB
or PCI, and one of the wifi-cards is connected to this phy. In order to
support switching the phy from USB to PCI, I needed to patch the
phy-driver. The patch is based on a rejected (at least last time I
checked) PCI-driver submitted to the linux-mediatek mailing list.

* The eMMC is configured to boot from the user area, and according to
the data sheet of the eMMC this value can't be changed.

* I tried to structure the MBR more nicely and use for example a
FAT32-parition for the kernel, so that we don't need to write/read from
some offset. The bootloader does not support reading from
FAT32-paritions. While the command (fatload) is there, it just throws an
error when I try to use it.

* I will submit and hope to get the DTS for the device accepted
upstream. If and when that happens, I will update the patches
accordingly.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2018-06-22 11:25:52 +02:00
Chen Minqiang e317bb06fd kernel: cleanup offload hooks on netdev unregister
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-06-22 11:01:42 +02:00
Mathias Kresin 004fe89620 lantiq: fix arcadyan vg3503j switch port indexing
Both version of the vg3503j have the LAN1 labelled port connected to
switch port 4 and the LAN2 labelled port connected to switch port 2.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-21 22:00:03 +02:00
Chuanhong Guo ed40173dfc ramips: Add support for Phicomm K2G
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA.
- UART: 1 x UART on PCB - 57600 8N1

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-06-21 22:00:02 +02:00
Tobias Schramm 5684d08741 ramips: Add support for Mikrotik RouterBOARD RBM33g
This commit adds support for the Mikrotik RouterBOARD RBM33g.

=Hardware=

The RBM33g is a mt7621 based device featuring three gigabit ports, 2
miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male
onboard RS-232 serial port. Additionally there are a lot of accessible
GPIO ports and additional buses like i2c, mdio, spi and uart.

==Switch==

The three Ethernet ports are all connected to the internal switch of the
mt7621 SoC:

port 0: Ethernet Port next to barrel jack with PoE printed on it
port 1: Innermost Ethernet Port on opposite side of RS-232 port
port 2: Outermost Ethernet Port on opposite side of RS-232 port
port 6: CPU

==Flash==

The device has two spi flash chips. The first flash chips is rather small
(512 kB), connected to CS0 by default and contains only the RouterBOOT
bootloader and some factory information (e.g. mac address).
The second chip has a size of 16 MB, is by default connected to CS1 and
contains the firmware image.

==PCIe==

The board features three PCIe-enabled slots. Two of them are miniPCIe
slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2).
Each of the miniPCIe slots is connected to a dedicated mini SIM socket
on the back of the board.

Power to all three PCIe-enabled slots is controlled via GPIOs on the
mt7621 SoC:

PCIe0: GPIO9
PCIe1: GPIO10
PCIe2: GPIO11

==USB==

The board has one external USB 3.0 port at the rear. Additionally PCIe
port 0 has a permanently enabled USB interface. PCIe slot 1 shares its
USB interface with the rear USB port. Thus only either the rear USB port
or the USB interface of PCIe slot 1 can be active at the same time. The
jumper next to the rear USB port controls which one is active:

open: USB on PCIe 1 is active
closed: USB on rear USB port is active

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack. The input voltage range is 11-32 V.

=Installation=

==Prerequisites==

A USB -> RS-232 Adapter and a null modem cable are required for
installation.

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM33G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output
directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the created
license file.**

Serial settings: 115200 8N1

The installation is a two-step process. First the
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted
via tftp:

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin"
   initramfs image
2. Connect to WAN port (left side, next to sys-LED and power indicator)
3. Connect to serial port of board
4. Power on board and enter RouterBOOT setup menu
5. Set boot device to "boot over ethernet"
6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server
   allows dynamic bootp)
6. Save config
7. Wait for board to boot via Ethernet

On the serial port you should now be presented with the OpenWRT boot log.
The next steps will install OpenWRT persistently.

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device
   using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin"

Once the flashing completes reboot the router and let it boot from flash.
It should boot straight to OpenWRT.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00
Tobias Schramm c0167abcb0 ramips: Add lzma-loader targets
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00
Tobias Schramm 4fa85a625f ramips: Add support for mt7621 to lzma-loader
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00
Deng Qingfang feb0a0bf22 ramips: fix Newifi D1 mtd partition
Newifi D1 has 32 MiB flash, so the firmware partition size should be 0x1fb0000

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-06-21 06:54:42 +02:00
Christo Nedev 48f311a112 brcm2708: Add wifi driver, firmware and NVRAM for Raspberry Pi 3 b
2708 -> 43430 -> pi0w

2709 -> 43430 -> pi3b
2709 -> 43455 -> pi3bplus

2710 -> 43430 -> pi3b
2710 -> 43455 -> pi3bplus

Signed-off-by: Christo Nedev <christo.nedev@gmail.com>
2018-06-20 21:50:14 +02:00
Arvid E. Picciani bf39d5594b ar71xx: add support for TP-LINK Archer C7 v5
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.

Specification:

- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Arvid E. Picciani <aep@exys.org>
2018-06-20 15:36:19 +02:00
Daniel Engberg c6e02b49f6 octeon: Add and set CPU type Octeon+ as default
The lowest CPU type used by supported Octeon platform
is Octeon+ (EdgeRouter Lite) while EdgeRouter Pro/ER-8 uses
Octeon II which is backwards compatible with Octeon+.

Sources:
https://community.ubnt.com/t5/EdgeRouter/EdgeRouter-Pro-CPU/td-p/654599
https://www.cavium.com/octeon-II-CN68XX.html
"OCTEON II family is fully software compatible with the widely-adopted
OCTEON Plus family"

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2018-06-20 15:36:02 +02:00
Daniel Golle 969fe206bd brcm2708: Add wifi driver, firmware and NVRAM for RPi1
Apparently there are RPi1 devices with BRCM43430 wifi, such as the
Pi Zero W. Add the necessary packages for that to the image generated
for those boards as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-20 11:19:26 +02:00
Johann Neuhauser dcc942e666 ath79: ar934x: use irq-ath79-intc driver and enable wmac
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-06-20 11:12:00 +02:00
Johann Neuhauser b8562f168b ath79: qca95xx: add new intc2, correct intc3 and add second pcie on qca9557
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-06-20 11:12:00 +02:00
Johann Neuhauser c7efc93509 ath79: fix irq-ath79-intc driver and add support for other ath79 SoCs
Add the missing enable and disable function.
Remove dummy mask and unmask function and use the one provided by
irq_dummy_chip.
Allow interrupt status register being defined from dts.
Add ddr_wb_flush for ar934x/qca953x.
Rename controller name to qca,ar9340-intc because this design was
first introduced in AR934x.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-06-20 11:12:00 +02:00
INAGAKI Hiroshi 189815462c ramips: add support for ELECOM WRC-1167GHBK2-S
ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
  - MediaTek MT7615D
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 2x keys
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin"
2. Connect the computer to the LAN port of WRC-1167GHBK2-S
3. Connect power cable to WRC-1167GHBK2-S and turn on it
4. Access to "http://192.168.2.1/details.html" and open firmware
update page ("手動更新(アップデート)")
5. Select the factory image and click apply ("適用") button
6. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 20:46:21 +02:00
INAGAKI Hiroshi 4645a6d318 ipq806x: add support for NEC Aterm WG2600HP
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.

Specification:

- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
  - RX, TX, NC, GND, Vcc from power connector side
  - baudrate: 115200 bps

Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
  /dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
  fw_setenv ipaddr "192.168.0.1"
  fw_setenv serverip "192.168.0.2"
  fw_setenv autostart "yes"
  fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
  bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 20:46:01 +02:00
Mathias Kresin 4bb6ee465e ramips: mt7621: fix wireless package selection
Add wpad-mini if wireless drivers are included. Drop the mt76 package if
both of the provided drivers are included with their own packages.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-19 20:45:29 +02:00
Evgeniy Didin 56f3aee531 arc770: bump kernel to 4.14
Currently arc770 is no more "source-only".
Lets update Linux kernel version from 4.9 to 4.14 for arc770.
config-4.14 was simply regenerated with "make kernel_menuconfig".

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
2018-06-19 14:32:47 +02:00
David Ehrmann 81d446b045 ar71x: add support for Mikrotik Routerboard wAP R
This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change
is based on 3b15eb0 which added support for the wAP 2nD. This change lacks
LED support.

Specifications:

- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9531, 802.11b/g/n 2x2:2
- Ethernet: 1x100Mbps
- Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack
- SIM card slot
- Mini-PCIe slot

Installation:

1. Login to the Mikrotik WebUI to backup your licence key
2. Change the following settings in System->Routerboard->Settings:
  - Boot device: try ethernet once then NAND
  - Boot protocol: DHCP
  - Force Backup Booter: checked
3. Setup a DHCP/BOOTP server with:
  - DHCP-Option 66 (TFTP server name) pointing to a local TFTP
    server within the same subnet of the DHCP range
  - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
    of the to be booted image, e.g.
    openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
4. Power off the device
5. If this is the second attempt to boot OpenWRT or the boot device isn't
   "try ethernet once then NAND," press and hold the reset button while
   powered off. If this is the first attempt, this step isn't necessary.
6. Power on the device, holding the reset button for 15-20s if already
   pressed from the previous step.

The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started OpenWRT via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT.

Revert to RouterOS

Use the "rbcfg" package on in OpenWRT:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply

Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.

Signed-off-by: David Ehrmann <ehrmann@gmail.com>
2018-06-19 14:32:47 +02:00
Felix Fietkau 9a4253b81f ramips: improve ethernet driver performance with GRO/TSO
GRO stores packets as fraglist. If they are routed back to the ethernet
device, they need to be re-segmented if the driver does not support
sending fraglists.
Add the missing support for that, along with a missing feature flag that
allows full routed GRO->TSO offload.
Considerably reduces CPU utilization for routing

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-19 09:45:28 +02:00
John Crispin c49ae68cba ath79: fix qm5p-ac-v2 dts file
Signed-off-by: John Crispin <john@phrozen.org>
2018-06-18 23:23:30 +02:00
David Bauer b4bf43c667 ar71xx: add support for Fritz!WLAN Repeater 450E
This commit adds support for the AVM Fritz!WLAN Repeater 450E

SOC:    Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4GHz WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - Most LEDs

Not working:
 - 2 RSSI LEDs
   AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they
   control over MDIO. Our driver doesn't expose these LEDs as GPIOs.
   While it is possible to implement this feature, it would require an
   additional kernel patch for a minor functionality.

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-18 23:23:30 +02:00
David Bauer abb4ab076f ar71xx: fix incorrect speed setting on QCA9556
The QCA9556 only has a SGMII interface. However the speed on the
ethernet link is set for the non-existant xMII interface.

This commit fixes this behavior.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-18 23:23:30 +02:00
Lucian Cristian b1a173d7c3 ath79: add support for tl-wr1043nd v2/v3
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-18 20:29:38 +02:00
Marty E. Plummer 0e81968ee8 ath79: add initial nand support for gl-ar300m
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
2018-06-18 20:29:38 +02:00
Marty E. Plummer fe3b62bbdc ath79: initial gl-ar300m support
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
2018-06-18 20:29:38 +02:00
Hannu Nyman 414ce80c07 mvebu: enable CONFIG_HW_RANDOM
Enable the Hardware Random Number Generator Core infrastructure
in kernel.

Needed for hardware random number generator drivers like chaoskey

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-06-18 20:29:38 +02:00
John Crispin ee1dbffeed ipq806x: D7800 only has a single sata port
Signed-off-by: John Crispin <john@phrozen.org>
2018-06-18 20:29:37 +02:00
Vincent Wiemann 076d2ea682 mips: fix dynamic ftrace
The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as
dynamic ftrace depends on -mlong-calls.
See http://patchwork.linux-mips.org/patch/675/
Thus we always set -mlong-calls if the kernel is being
compiled with dynamic ftrace support.

Signed-off-by: Vincent Wiemann <webmaster@codefetch.de>
2018-06-18 20:29:26 +02:00
Jeremiah McConnell e820455198 mvebu: backport ahci_mvebu errata patchset
Marvell ahci hardware requires a workaround to prevent eSATA failures
on hotplug/reset when used with multi-bay external enclosures.

Errata Ref#226 - SATA Disk HOT swap issue when connected through Port
Multiplier in FIS-based Switching mode.

These patches backport the workaround from 4.17.

Signed-off-by: Jeremiah McConnell <miah@miah.com>
2018-06-18 20:28:20 +02:00
Lucian Cristian c8e76cd4ff ath79: fix rx ring buffer stall qca956x
when ported from ar71xx to ath79 the qca9560-eth was omitted

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-18 18:21:20 +02:00
Thomas Nixon bb71a3f27e ar71xx: add kmod-usb-ehci to fix USB on RB hAP AC
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
2018-06-18 18:21:20 +02:00
Magnus Frühling 4b280ad91a ipq40xx: add support for ZyXEL WRE6606
Specifications:
SOC:	Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:	128 MB Nanya NT5CC64M16GP-DI
FLASH:	16 MiB Macronix MX25L12845EMI-12G
ETH:	Qualcomm QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT:  WPS, Mode-toggle-switch
LED:	Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
        (LAN not controllable by software)
        (WLAN each green / red)
SERIAL:	Header next to eth-phy.
        VCC, TX, GND, RX (Square hole is VCC)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet (Correct MAC-address)
 - 2.4 GHz WiFi (Correct MAC-address)
 - 5 GHz WiFi (Correct MAC-address)
 - Factory installation from tftp
 - OpenWRT sysupgrade
 - LEDs
 - WPS Button

Not Working:
 - Mode-toggle-switch

Install via TFTP:

Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.

To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.

append-cmdline patch taken from chunkeeys work on the NBG6617.

Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
2018-06-18 18:21:20 +02:00
Lucian Cristian 71ae0792ba ath79: add tl-wr1043nd-v4 support everything is working
tplink-safeloader: resize kernel partition
kernel 4.14 is much bigger, resize the partition

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-18 18:21:20 +02:00
Lucian Cristian cad843e1f5 ath79: add ubiquiti unifi ap ac lite/lr
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-18 18:21:19 +02:00
Weijie Gao 52109ce71f ath79: ag71xx: fix pll-data setting for ar7242/ar934x/qca955x/qca956x
ar71xx/ar913x series use the old pll registers and settings.

However started from ar7242, a new pll register is introduced and the
pll setting is much simpler.

This can be observed from dev-eth.c from the ar71xx target.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-06-18 18:21:19 +02:00
Weijie Gao 97c5cbc496 ath79: add support for Phicomm K2T
This patch adds dts for qca956x and also support for Phicomm K2T

The qca965x.dtsi adds nearly all the necessary components.
Both ath9k AHB and PCIe worked well.

The Phicomm K2T uses MTD partition 'config' to store the mac addresses in
JSON format. To extract these fields correctly, a script is introduced:
    /lib/functions/k2t.sh
This script provides a helper function to extract mac addresses, and is used
in three places.

Hardware spec of Phicomm K2T:
CPU: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337
WiFi 5.8GHz: QCA9886

Flash instruction:
Apply sysupgrade.bin via serial console:

tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-06-18 18:21:16 +02:00
Chen Minqiang 8f804f42d5 ipq40xx: essedma: fixup ip align
This fixup ip align in essedma driver rx path
see cat /proc/cpu/alignment
which reports alignment-fixups without this fix.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-06-18 15:39:08 +02:00
Kevin Darbyshire-Bryant d600de3ddd kernel: atm: pppoatm fix vc-mux connection failures
Backport a hot off the press upstream kernel ATM fix:

Preserve value of skb->truesize when accounting to vcc

"There's a hack in pskb_expand_head() to avoid adjusting skb->truesize
for certain skbs. Ideally it would cover ATM too. It doesn't. Just
stashing the accounted value and using it in atm_raw_pop() is probably
the easiest way to cope."

The issue was exposed by upstream with:

commit 14afee4b6092fde451ee17604e5f5c89da33e71e
Author: Reshetova, Elena <elena.reshetova@intel.com>
Date:   Fri Jun 30 13:08:00 2017 +0300

    net: convert sock.sk_wmem_alloc from atomic_t to refcount_t

But an earlier commit left the ticking timebomb:

158f323b9868 ("net: adjust skb->truesize in pskb_expand_head()

Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging
assistance and to David Woodhouse <dwmw2@infradead.org> for further
guidance, cajoling & patience in interpreting the debug I was giving him
and producing a fix!

Fixes FS#1567

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-18 15:27:15 +02:00
Kevin Darbyshire-Bryant 0276e1f760 lantiq: atm: fix ifx_atm driver integration
When upstream kernel introduced commit c55fa3cccbc2c672e7f118be8f7484e53a8e9e77
we incorrectly updated our hack integration patch that updates atm/common.c

+++ b/net/atm/common.c
@@ -62,10 +62,16 @@ static void vcc_remove_socket(struct soc
        write_unlock_irq(&vcc_sklist_lock);
 }

+struct sk_buff* (*ifx_atm_alloc_tx)(struct atm_vcc *, unsigned int) = NULL;
+EXPORT_SYMBOL(ifx_atm_alloc_tx);
+
 static bool vcc_tx_ready(struct atm_vcc *vcc, unsigned int size)
 {
        struct sock *sk = sk_atm(vcc);

+       if (ifx_atm_alloc_tx != NULL)
+               return ifx_atm_alloc_tx(vcc, size)

The correct solution is to drop our ifx_atm_alloc_tx replacement hack
entirely and let the kernel do its thing.

In reality neither pppoatm or BR2684 interfaces actually hit this code,
so the incorrect integration would only be noticed with direct socket
calls which we are unaware of a use-case.

This is not the solution to pppoatm vc-mux failing to work which started
the whole investigation, but let's fix it up anyway.

With sincerest thanks to David Woodhouse <dwmw2@infradead.org> &
Mathias Kresin <dev@kresin.me>.

Tested-on: lantiq, BT HomeHub 5a

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-18 15:26:41 +02:00
Koen Vandeputte db73c71e8d kernel: bump 4.9 to 4.9.109
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-06-18 15:25:28 +02:00
Rafał Miłecki 93cc44c433 bcm53xx: exit if writing kernel during sysupgrade fails
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-06-18 13:47:08 +02:00
Rafał Miłecki c3d9109fad bcm53xx: drop not ready support for Luxul devices
Support for these devices isn't ready yet and it was only accidentally
pushed in the commit 0da9303e5b ("mac80211: backport "brcmfmac:
cleanup and some rework" from 4.17").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-06-18 08:46:23 +02:00
Tomasz Maciej Nowak f5bce268b0 mvebu: replace espressobin spi patch with upstream one
For easier future kernel bumps replace spi patch with upstream version
slightly modified. The modification removes partition definitions which
has been diffrent for some U-Boot versions.
Also this removes unnecessary i2c definition which was in the old patch.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-06-18 07:10:20 +02:00
Tomasz Maciej Nowak 772258044b mvebu: reduce speed to gen1 for espressobin pcie
Since the beginning there's been an issue with initializing the Atheros
based MiniPCIe wireless cards. Here's an example of kerenel log:

 OF: PCI: host bridge /soc/pcie@d0070000 ranges:
 OF: PCI:   MEM 0xe8000000..0xe8ffffff -> 0xe8000000
 OF: PCI:    IO 0xe9000000..0xe900ffff -> 0xe9000000
 advk-pcie d0070000.pcie: link up
 advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
 pci_bus 0000:00: root bus resource [bus 00-ff]
 pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
 pci_bus 0000:00: root bus resource [io  0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
 pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit]
 pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref]
 [...]
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
 ath9k 0000:00:00.0: enabling device (0000 -> 0002)
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40
 ath9k 0000:00:00.0: request_irq failed
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
 ath9k: probe of 0000:00:00.0 failed with error -22

The same happens for ath5k cards, while ath10k card didn't appear at
all (not detected):

 OF: PCI: host bridge /soc/pcie@d0070000 ranges:
 OF: PCI:   MEM 0xe8000000..0xe8ffffff -> 0xe8000000
 OF: PCI:    IO 0xe9000000..0xe900ffff -> 0xe9000000
 advk-pcie d0070000.pcie: link never came up
 advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
 pci_bus 0000:00: root bus resource [bus 00-ff]
 pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
 pci_bus 0000:00: root bus resource [io  0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
 advk-pcie d0070000.pcie: config read/write timed out

Following the issue on esppressobin.net forum [1] the workaround seems
to be limiting the speed of PCIe bridge to 1st generation. This fixed
the initialisation of all tested Atheros wireless cards.

The change shouldn't affect the performance for wireless cards,
it could reduce the performance of storage controller cards but since
OpenWrt focuses on wireless connectivity, fixing compatibility with
wireless cards should be a priority.

For the record, the iwlwifi and mt76 cards were not affected by this
issue.

1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-06-18 07:10:20 +02:00
Tomasz Maciej Nowak 4ec8c8c23e mvebu: add fix for armada 37xx cpufreq driver
Backport from stable kernel tree fixing clock leak.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-06-18 07:10:20 +02:00
Hauke Mehrtens 6745af9a0d mediatek: mt7622: Do not deactivate CONFIG_BLK_DEV
zram.ko needs CONFIG_BLK_DEV activated and it is by default for all
other targets in OpenWrt.

This makes zram.ko compile again.
Compile tested only.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-06-18 07:10:19 +02:00
Hauke Mehrtens 10ce015c65 mediatek: mt7622: Do not set CPU_SUBTYPE for Cortex A53
Neon and vfpv4 are mandatory extensions in the ARM64 instruction set
now, do not activate them explicitly. GCC will make use of these
extension now by default.

This makes it possible to share the toolchain with other Cortex A53
SoCs.
Compile tested only.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-06-18 07:10:19 +02:00
Zoltan HERPAI 1e0aeb2b55 ath79: move Netgear build code into a common makefile
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-06-18 07:10:19 +02:00
Koen Vandeputte 2b9885571b kernel: bump 4.14 to 4.14.49
Refreshed all patches

Compile-tested on: cns3xxx, imx6, x86-64
Runtime-tested on: cns3xxx, imx6, x86-64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-06-18 07:10:19 +02:00
Koen Vandeputte 8c1f088521 kernel: bump 4.9 to 4.9.108
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-06-18 07:10:19 +02:00
David Bauer 4fc005197a ipq40xx: add get_status_led to diag.sh
This commit adds the get_status_led method to diag.sh, which sets the
boot-led as status-led for scripts using this method to get a
status-led.

This method is used platform-independent in downstream project gluon to
set the LED used to indicate the config-mode.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-18 07:10:19 +02:00
Linus Walleij 1c1e254244 gemini: Cook SQ201 images
This generates the "rd.gz" and "hddapp.tgz" that doesn't contain
anything of the sort but rather the OpenWRT rootfs. It works the
same way as how we generate the same layout for the NAS4220b.
For some reason the ImageInfo file is different for the SQ201.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-06-18 06:35:33 +02:00
Linus Walleij d8072a3530 gemini: Add appropriate Wireless kernel modules
The D-Link DIR-685 has a RealTek RT2880 mini-PCI card in a
slot. Activate the appropriate kernel module.

The Square One SQ201 has a Ralink RT61-based mini-PCI card.
Activate the appropriate kernel modules. This fixes the
previous error just activating the firmware: the kernel
module will bring in the firmware it needs.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-06-18 06:35:16 +02:00
Linus Walleij dc7f540ce1 gemini: Cook a WRGG firmware image
This makes the Gemini build a WRGG-type firmware update
image for the DIR-685. This should hopefully install the
kernel from the web firmware upgrade API on the product
switching it permanently to use OpenWRT.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-06-18 06:35:09 +02:00
Rafał Miłecki 0da9303e5b mac80211: backport "brcmfmac: cleanup and some rework" from 4.17
It was described by Arend as:

> This series is intended for 4.17 and includes following:
>
>  * rework bus layer attach code.
>  * remove duplicate variable declaration.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-06-17 22:46:29 +02:00
Rafał Miłecki e53d0da775 bcm53xx: fix NAND partitions on D-Link DIR-885L
This fixes missing rootfs on above device:
[    2.652292] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
(...)
[    2.687909] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Fixes: 05cb6aa69f ("bcm53xx: replace linux,part-probe with a proper partitions subnode")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-06-17 22:41:15 +02:00
Johann Neuhauser 14cb05909a ath79: clean up led config script files for all devices
1. Move all status led definitions out of diag.sh into device dt
   as we use here a generic script hook.

2. Encode "phy0ptp" led trigger in dt of device for all ath79 devices.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-06-16 10:08:51 +02:00
Hannu Nyman 25ea21d765 ath79: fix WNDR3800 support
Fixes for WNDR3800 DTS:
* fix bootcmd
* name art partition to reference it for MACs
* format firmware partition's address similarly as others
* make u-boot-env read-only like in ar71xx
* read wan and lan MACs from art
* fix LED and button gpio values to match ar71xx
  (orange/green powerLED, reset button)
* enable power LED in dts by alias led-status
* define USB LED triggers and connect to USB port
* change wifi button to KEY_RFKILL like in ar71xx

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-06-16 10:08:51 +02:00
Johann Neuhauser 10f8823254 ath79: led-resets: add default-trigger property
Add support for the common led property "linux,default-trigger". It
allows to set a default led trigger via devicetree.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-16 10:08:51 +02:00
Lucian Cristian f7a220b2f6 ath79: fix usb led on wr-1043nd-v1
usb port was not triggered correctly
also remove uneded wifi led trigger from the script

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-16 10:08:51 +02:00
Alex Maclean ab5b359876 ath79: fixup TL-WR703N/TL-MR10U split
Readd SoC compatible strings and correct model names mangled in
a51078f735, cleanup dts to remove
duplication, rename dtsi for clarity, use correct GPIO for TL-MR10U
USB power.

Tested only on TL-WR703N due to lack of a TL-MR10U.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-16 10:08:51 +02:00
Maxim Anisimov 8956eb502d ramips: add support for TP-Link TL-WR842N v5
TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and
non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 7x LED, 2x button, power input switch

Flash instruction:

The only way to flash OpenWrt image in wr842nv5 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-06-16 10:08:51 +02:00
David Bauer 82fa7b9d78 ramips: use phytpt trigger for mt76 wireless
With this change, the LED trigger is independent from the (wireless)
netdev name. The (wireless) netdev name can be easiliy changed in
OpenWrt and would require an update of the netdev trigger settings each
time it is done.

This change is (for now) applied only to MT7628 devices from TP-Link, as
we only had the possibility to test this change against two of those
devices, namely a TL-WR841 v13 and a Archer C50 v3.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-16 10:08:51 +02:00
lbzhung 291e34edff ramips: fix mt7688 watchdog register base addr
I found mt7688 watchdog not working. The watchdog registers are identical
for mt7621 and mt7628/mt7688. The first watchdog related register is at
0x10000100, the last one - a 16bit sized - at 0x10000128.

Set the correct register address and size in the dtsi file to get the
watchdog working.

Signed-off-by: lbzhung <gewalalb@gmail.com>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-16 10:08:51 +02:00
Mathias Kresin 5da2c68d00 ramips: mt7621: fix mtu setting with kernel 4.14
Since kernel 4.10 commit 61e84623ace3 ("net: centralize net_device
min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which
is [68, 1500] by default.

It's necessary to set a max_mtu if a mtu > 1500 is supported.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-16 10:08:51 +02:00
Daniel Golle 0653e31270 lantiq-vdsl-fw: update to provide recent vectoring firmware
Recent Speedport firmware downloads only work over HTTPS, so the user
either needs to provide the already downloaded file or install
ustream-ssl-* as well as ca-certificates or ca-bundle.

So to get VDSL2 with vectoring on xRX200, simply run
vdsl_fw_install.sh
on the target and either provide the downloaded file as instructed or
make sure the device is connected to the Internet and can download that
HTTPS url itself.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-15 12:45:37 +02:00
Daniel Golle 8e2f8b0c83 Revert "lantiq: get rid of ltq-vdsl-fw"
This reverts commit 0938233fcd.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-15 12:45:37 +02:00
Daniel Golle 037ef13a16 brcm2708: move wifi calibration EEPROMs out of base-files
Ship EEPROM blobs for specific supported board only and don't have them
lurking around in our source tree but rather download them from
@github/RPi-Distro/firmware-nonfree upstream.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-14 18:15:33 +02:00
Daniel Golle a2f17214cd brcm2708: add brcmfmac-firmware-43455-sdio to DEFAULT_PACKAGES
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-14 13:54:17 +02:00
Daniel Golle 3a40a7d5a5 brcm2708: add RPi3+ wifi calibration data
Add files from
https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm/brcmfmac43455-sdio.txt
https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm/brcmfmac43455-sdio.clm_blob

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-14 13:54:17 +02:00
Felix Fietkau 5101515375 kernel: fix conntrack fixup of offloaded flows on timeout
Fixes excessively long conntrack timeout of short lived connections

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-14 11:25:24 +02:00
Felix Fietkau 68ab89854f kernel: fix conntrack leak for flow_offload connections
This was caused by a race condition between offload teardown and
conntrack gc bumping the timeout of offloaded connections

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-13 12:54:45 +02:00
Felix Fietkau e820734f79 kernel: allow hardware NAT offload drivers to keep a priv pointer
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-13 12:54:25 +02:00
Felix Fietkau ec502cd3fe ramips: rename ethernet driver folder to the same one that upstream uses
Preparation for sharing offload code with the mediatek target through
generic files/

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-13 12:54:25 +02:00
Felix Fietkau b560c1748a kernel: avoid flow offload for connections with xfrm on the dst entry (should fix IPSec)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-13 12:54:25 +02:00
Kevin Darbyshire-Bryant f60301db74 kernel: bump 4.9 to 4.9.107
Refresh patches.

Compile-tested for: ar71xx
Run-tested on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-09 22:39:17 +02:00
Jeremiah McConnell 390c4df2c0 mvebu: enable SATA port multiplier support
Some of the Marvell targets have functional SATA port multiplier
support, which is required for multi-bay eSATA enclosures.  Enable
kernel support by setting CONFIG_SATA_PMP.

Closes: FS#1232 and FS#547

Signed-off-by: Jeremiah McConnell <miah@miah.com>
2018-06-09 16:32:39 +02:00
Matthias Badaire 6ea0807f18 ramips: fix network config for ravpower wd03
This device has only one ethernet port.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[add the existing eth0 as lan block, shorten commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-09 13:45:29 +02:00
David Bauer daeab36c1b ar71xx: use Power-LED as Diag-LED on FRITZBox 4020
This commit makes use of the Power-LED as Diag-LED, allowing the LED to
work as a status indicator.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-09 13:45:29 +02:00
David Bauer 9ec117c5be ar71xx: fix AVM package selection
The AVM package selection partially broke with the addition of the
FRITZ!Box 4020. This commit restores the intended behavior.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-09 13:45:29 +02:00
Lucian Cristian c8677ca89e ath79: add tl-mr3020-v1 support
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-08 12:19:49 +02:00
Karl Palsson 8c15fb5240 ath79: wr1043: fix DTC warnings
Use the "correct" unit name to avoid DTC warnings.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:29 +02:00
Karl Palsson 5e69dce0e7 ath79: glinet ar150: fix DTC warnings
Supply a unit name to match other .dts files and avoid DTC warnings.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:28 +02:00
Karl Palsson 9dad82c5d6 ath79: ubnt: fix DTC warnings
Use explicit labels instead of units with no reg's to avoid DTC
warnings.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:28 +02:00
Karl Palsson 93ff973c97 ath79: wdr4300: avoid DTC warnings
Use direct button labels to avoid dtc warnings

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:28 +02:00
Karl Palsson 29b2804c6b ath79: buffalo_wzr-hp-g450h: fix dtc warnings
Just name buttons directly, rather than abstract and then also a label.
Likewise for leds.  Avoids DTC warnings about unit address with no reg
parameter.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:28 +02:00
Karl Palsson 97326e5131 ath79: avm_fritz300e: avoid dtc warnings
Use number formats preferred by the device tree compiler

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:28 +02:00
Karl Palsson d25d847e78 ath79: mdio: add address-cells and size-cells defaults
Eliminates warnings about relying on defaults from the device tree
compiler.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:27 +02:00
Karl Palsson 35aae0735c ath79: ar9330.dtsi: fix typo in USB unit name
Make the unitname match the reg address.  This fixes a DTC warning.

Tested that USB is still functional on an ar9331 device including this
dtsi.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:27 +02:00
Karl Palsson 1588114cf2 ath79: add etactica-eg200 support
Based on original ar71xx eg200 board files

Tested working:
* usb hub, storage and serial port
* ethernet
* wifi
* leds
* button

sysupgrade from self->self passes validity checks.
sysupgrade from old ar71xx->ath79 passes. (however this doesn't migrate
wireless driver configs)

Only unknown issue is the existance of a /sys/class/leds/ath9k-phy0,
which doesn't "exist"

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-06-08 09:56:27 +02:00
INAGAKI Hiroshi a32c06f44d ramips: add support for I-O DATA WN-GX300GR
I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek
MT7621S.

Specification:

- MT7621S (1-Core, 2-Threads)
- 64 MB of RAM
- 8 MB of Flash (SPI)
- 2T2R 2.4 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 115200 bps (U-Boot, OpenWrt)

Flash instruction using initramfs image:

1. Connect serial cable to UART header
2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR"
and place it in the TFTP directory
3. Set the IP address of the computer to 192.168.99.8, connect to the
LAN port of WN-GX300GR, and start the TFTP server on the computer
4. Connect power cable to WN-GX300GR and turn on the router
5. Press "1" key on the serial console to interrupt boot process on
U-Boot, press Enter key 3 times and start firmware download via TFTP
6. WN-GX300GR downloads initramfs image and boot with it
7. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-GX300GR
8. Wait ~150 seconds to complete flasing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-08 09:56:27 +02:00
Adoal Xu a51078f735 ath79: add TP-Link TL-MR10U port
Signed-off-by: Adoal Xu <adoalxu@gmail.com>
2018-06-08 09:56:15 +02:00
Sven Eckelmann 4f6320704f ar71xx: Fix offset to WMAC address for 8devices Lima
The ART partition of the Lima board stores exactly three mac addresses:

* 0x0: eth0
* 0x6: eth1
* 0x1002: wmac

The first two are correctly assigned in the mach file but the latter points
to 0x800. But this position is set to ff:ff:ff:ff:ff:ff. Luckily, the
driver falls back in ath9k_hw_init_macaddr to the EEPROM mac address when
it doesn't find a valid mac address in the platform_data.

Remove this bogus offset to the ART partition to directly load the wmac via
the EEPROM data in the ART partition.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2018-06-08 09:39:14 +02:00
Rosen Penev 289b2f5e85 ramips: mt7621: Fix some cosmetic DTC warnings
Node /cpus/cpu@0 has a unit name, but no reg property
Node /cpus/cpu@1 has a unit name, but no reg property
Node /cpuintc@0 has a unit name, but no reg property
Node /cpuclock@0 has a unit name, but no reg property
Node /sysclock@0 has a unit name, but no reg property
Node /pcie@1e140000/pcie0 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie0 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie1 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie1 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie2 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie2 missing bus-range for PCI bridge

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-06-08 09:31:37 +02:00
Rosen Penev 66cc6dd6c4 ramips: mmc: Add back some non-mt7621 code that staging removed
This reverts commit 8a570921b5.

This seems to have been accidentally reverted. This fixes mt7620 and
mt7628.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
2018-06-08 09:31:36 +02:00
Kevin Darbyshire-Bryant 8110bf18f4 ramips: mir3g dts define usb port Vcc volt regulator GPIO
Define USB port power on/off GPO as voltage regulator type instead of
exposing as a normal GPIO.

The GPO is now controlled by the USB driver via the voltage regulator
definition.  The regulator is of fixed output type (5V for USB) hence the
GPO switches power on/off to USB pin 1 (Vcc)

USB port power is enabled on driver load and disabled on driver unload.

Enable kernel support for fixed voltage regulator types on mt7621.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-08 09:31:36 +02:00
Christian Lamparter 4363b5362f ipq40xx: flesh out MR33's pcie dts definitions
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-06-08 09:31:36 +02:00
Christian Lamparter 146fbeb81c ipq40xx: fix OpenMesh A62 dtc warnings
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0 missing ranges for PCI bridge (or not a bridge)
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0 missing bus-range for PCI bridge
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 node name is not "pci" or "pcie"
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 missing ranges for PCI bridge (or not a bridge)
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 incorrect #address-cells for PCI bridge
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 incorrect #size-cells for PCI bridge
Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 missing bus-range for PCI bridge
Warning (unit_address_format): Failed prerequisite 'pci_bridge'
Warning (pci_device_reg): Failed prerequisite 'pci_bridge'
Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'

Cc: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-06-08 09:31:36 +02:00
Christian Lamparter 2f1fa04587 ipq40xx: fix dtc warning about /soc/ad-hoc-bus missing a unit name
This patch fixes a dtc warning that shows up for every device
Warning (unit_address_vs_reg): Node /soc/ad-hoc-bus has a reg or ranges property, but no unit name

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-06-08 09:31:35 +02:00
Christian Lamparter b22e37528b ipq40xx: set #size-cells to 0 to fix warning
qcom-ipq4018-ex6100v2.dtb: Warning (reg_format): "reg" property in
	/led_spi/led_gpio@0 has invalid length (4 bytes)
qcom-ipq4018-ex6100v2.dtb: Warning (avoid_default_addr_size):
	Relying on default #size-cells value for /led_spi/led_gpio@0

Cc: Thomas Hebb <tommyhebb@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-06-08 09:31:35 +02:00
Koen Vandeputte 55b4b1eba0 ar71xx: fix USB switch to mPCIE for Mikrotik rb91x boards
Some devices like the Mikrotik RB912 only have 1 USB port
which is shared between an USB A type port, and the mini PCIe socket.

Toggling a gpio selects the output to which USB is connected.

Since kernel 4.9, gpio base is rounded up to a value of 32.

Commit 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that.
In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32
This means that the USB toggle gpio number actually also changes from 52 to 61.

But ..
Some of these GPIO numbers are also used in other locations, like the boardfile.
The author forgot to also change them over there.

Switching the USB port to mPCIe now shows my modem is correctly discovered again:

[ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3
[ 2864.062728] usb 1-1: config 1 has no interface number 1
[ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected
[ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0
[ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected
[ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1
[ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected
[ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2
[ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device
[ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11

Fixes: 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: Robin Leblon <robin.leblon@ncentric.com>
Cc: Felix Fietkau <nbd@nbd.name>
2018-06-08 09:31:35 +02:00
Lucian Cristian a0a616e1b8 ath79: fix qca956x SoC boot
based on old ar71xx irq.c driver

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-07 09:38:52 +02:00
David Bauer e36f8b3f39 ar71xx: add support for OCEDO Koala
This commit adds support for the OCEDO Koala

SOC:	Qualcomm QCA9558 (Scorpion)
RAM:    128MB
FLASH:  16MiB
WLAN1:  QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2:  QCA9880 5 GHz 802.11nac 3x3
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-07 09:31:58 +02:00
Hannu Nyman fb8a578aa7 ipq806x: Enlarge R7800 flash - use netgear partition
Increase the available flash memory size in Netgear R7800
by taking into the use the unused "netgear" partition
that is located after the firmware partition.

Available flash space for kernel+rootfs+overlay increases
by 68 MB from 32 MB to 100 MB.

In a typical build, overlay space increases from 15 to 85,
increasing the package installation possibilities greatly.

Reverting to the OEM firmware is still possible, as the OEM
firmware contains logic to initialise the "netgear" partition
if its contents do not match expectations. In OEM firmware,
"netgear" contains 6 UBI sub-partitions that are defined in
/etc/netgear.cfg and initialisation is done by /etc/preinit

Tested with Openwrt master r7093-4fdc6ca31b and OEM V1.0.2.52

Reference to forum discussion in Netgear R7800 exploration thread:
https://forum.lede-project.org/t/netgear-r7800-exploration-ipq8065-qca9984/285/1118
(messages 1118-1158)

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-06-07 09:19:39 +02:00
Rosen Penev fff65dbe24 ipq806x: Limit NR_CPUS to 2
ipq806x is all dual core processors. ipq807x is quad core. Removes this
from dmesg:

RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-06-07 09:06:19 +02:00
Koen Vandeputte 2792ef55ab kernel: bump 4.9 to 4.9.106
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-06-07 09:04:46 +02:00
Catrinel Catrinescu dc1268cb11 ath79: add WLAN, Ethernet-Switch with LAN/WAN and Status LED to Dorin
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
2018-06-07 09:02:04 +02:00
Luis Araneda 32ab2e16b1 zynq: remove support for kernel 4.4
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Luis Araneda 88f7e2386a zynq: switch to kernel 4.14
Also, remove the source-only qualifier

Run-tested: ZedBoard

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Luis Araneda 19c3dc60e4 zynq: refresh kernel 4.14 configuration
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Luis Araneda 74dffd592b zynq: copy config to kernel 4.14
The file will be used as a base configuration
for kernel 4.14

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Luis Araneda 61b977fa2c zynq: fix detection of the zybo board
The board_name was being tested for "xlnx,zynq-zybo",
but the .dts compatible string is "digilent,zynq-zybo"

Also, sorted the boards alphabetically, and added an
error message for unsupported boards

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Luis Araneda 7967e6c067 zynq: remove hard-coded network configuration
This is no longer necessary since commit 57776e6
(base-files: remove default /etc/config/network,
generate it via board.d instead)

Run-tested: ZedBoard

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Luis Araneda dfac3ffd07 zynq: reworked image creation process
After commit a1248da (zynq: convert to new image build code),
all boards, became unbootable, entering into a boot loop.

Replace the compressed kernel zImage by an uncompressed Image,
which is compressed after with gzip. Also, enable the creation
of an initramfs image by default.

Change images' filename to match the compatible string from the
respective .dts file (<vendor>_<model>). Also, use the shared
mkits.sh script and remove the target specific one.

Fixes: FS#1204

Run-tested: ZedBoard

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Daniel Golle 8796680277 ramips: fix reboot with W25Q256 with 4-address-mode enabled
Some board vendors actually changed the loader to expect the chip
to come up in 4-address-mode and flipped the ADP bit in the flash
chip's configuration register which makes it come up in 4-address-mode.
Hence it doesn't make sense to avoid switching to 4-address-mode on
those boards but the opposite as otherwise reboot hangs eg. on the
WrtNode2 boards. Fix this by checking the ADP register and only using
SPI_NOR_4B_READ_OP on chips which have ADP==0 (come up in 3-byte mode).

See also datasheet section 7.1.11 Power Up Address Mode (ADP)

Fixes: 22d982ea0 ("ramips: add support for switching between 3-byte and 4-byte addressing on w25q256 flash")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-07 02:34:13 +02:00
Matthias Schiffer 0c0bb62999
ar71xx: switch CPE/WBS 210/510 to okli-loader
We recently increased the kernel partition size of the CPE/WBS 210/510.
This works fine for new installations of the factory image, but on
sysupgrades, the partition table read by the bootloader is not adjusted.
This limits the maximum size of the kernel loaded by the bootloader to the
old partition size.

While adjusting the partition table would be a cleanest solution, such a
migration would have to happen before an upgrade to a new version with a
newer kernel. This is error-prone and would require a two-step upgrade, as
we mark the partition table partition read-only.

Instead, switch from the lzma-loader with embedded kernel to the
okli-loader, so only the tiny lzma-loader is loaded by the bootloader as
"kernel", and the lzma-loader will then load the rest of the kernel by
itself.

Fixes: e39847ea2f ("ar71xx: increase kernel partition size for CPE/WBS 210/510")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:53 +02:00
Matthias Schiffer c57e182b56
ath79: lzma-loader: sync with ar71xx target
Import all improvements made in the lzma-loader since development on the
ath79 target started.

This also reverts fe594bf90d ("ath79: fix loader-okli, lzma-loader"), as
is obsoleted by 2ad60168b6af ("ar71xx: lzma-loader: move padding workaround
to gzip step").

Likely, many of the changes should be ported to the ramips lzma-loader as
well, but I don't have a device to test this.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:53 +02:00
Matthias Schiffer 108a6f6792
ar71xx: make loader-okli build step more generic
Add support for different loader types.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:53 +02:00
Matthias Schiffer 9968dcedb4
ar71xx: lzma-loader: constify kernel argv array
By making the kernel argv array const, the .data section can always be
omitted from the laoder binary.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:52 +02:00
Matthias Schiffer 8d851a95b7
ar71xx: lzma-loader: set page size to 4KB
The text section in the ELF loader is aligned to the maximum page size,
which defaults to 64KB. Reduce it to the actual page size to avoid wasting
flash space for this alignment.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:52 +02:00
Matthias Schiffer a28e46b7cc
ar71xx: lzma-loader: move padding workaround to gzip step
Some devices (TP-Link TL-WR1043ND v1) don't boot reliably when the
uncompressed loader is too small. This was workarounded in the loader by
adding 512KB of padding to the .data section of the loader binary.

This approach had two issues:

- The padding was only working when .data was non-empty (otherwise the
  section would become NOBITS, omitting it in the binary). .data was only
  empty when no CMDLINE was set, leading to further workarounds like
  fe594bf90d ("ath79: fix loader-okli, lzma-loader"), and this
  workaround was only effective because a missing "const" led to the kernel
  argv being stored in .data instead of .rodata
- The padding was not only added to the compressed .gz loader, but also
  uncompressed .bin and .elf loaders. The prevented embedding the kernel
  cmdline in the loader for non-gz loader types.

To fix both issues, move the creation of the padding from the linker script
to the gzip step.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:25:52 +02:00
Stijn Tintel e52f3e9b13 kernel: bump 4.14 to 4.14.48
Remove upstreamed patches:
generic/pending/101-clocksource-mips-gic-timer-fix-clocksource-counter-w.patch
generic/pending/103-MIPS-c-r4k-fix-data-corruption-related-to-cache-coherence.patch
generic/pending/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch
lantiq/0025-MIPS-lantiq-gphy-Remove-reboot-remove-reset-asserts.patch
Update patches that no longer apply:
generic/pending/811-pci_disable_usb_common_quirks.patch
ath79/0009-MIPS-ath79-add-lots-of-missing-registers.patch

Fixes CVE-2018-6412.

Compile-tested: octeon, x86/64.
Runtime-tested: octeon, x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-06-05 22:54:00 +03:00
Daniel Golle 187da94808 kernel: modules: package module for Exar 8250 UARTs
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-05 15:27:36 +02:00
Felix Fietkau 2f3b1dddea kernel: backport patch to fix dst handling for offloaded connections
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-05 10:18:58 +02:00
Michael Gray 4fdc6ca31b mvebu: fix broken console on WRT32X (venom)
The console bootarg is being corrupted on boot, causing various issues
including broken sysupgrade.
Utilising the bootargs mangle patch from other targets, hardcode the console
arguments and fetch the rootfs from the bootloader.

Kernel command line: console=ttyS0,115200 root=/dev/mtdblock8

Bootloader command line (ignored): console= root=/dev/mtdblock8

Please cherry pick to 18.06 too

Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-06-01 21:01:03 +02:00
Daniel Golle dcc34574ef oxnas: bring in new oxnas target
Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.

Functional issues:
 * PCIe won't come up (hence no USB3 on Shuttle KD20)
 * I2C bus of Akitio myCloud device is likely not to work (missing
   debounce support in new pinctrl driver)

Code-style issues:
 * plla/pllb needs further cleanup -- currently their users or writing
   into the syscon regmap after acquireling the clk instead of using
   defined clk_*_*() functions to setup multipliers and dividors.
 * PCIe phy needs its own little driver.
 * SATA driver is a monster and should be split into an mfd having
   a raidctrl regmap, sata controller, sata ports and sata phy.

Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-01 15:45:06 +02:00
Daniel Golle 17511a7ea8 oxnas: kill old oxnas target
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-01 15:45:06 +02:00
Hans Dedecker 0777a3e773 kernel: re-add export ipv6_push_frag_opts for tunneling now patch
The patch got removed by commit 7dca1bae82 (kernel: bump to 4.9.105)
but is still required as ipv6_push_frag_opts needs to be exported.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-06-01 14:08:42 +02:00
John Crispin 7197744cd6 Revert "ramips: Move PCI driver to files directory"
This reverts commit a098a78a33.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:20 +02:00
John Crispin 69929dac89 Revert "ramips: Remove redundant owner assignment"
This reverts commit 2ad4daf579.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:14 +02:00
John Crispin 64878a5616 Revert "ramips: improve interrupt mapping"
This reverts commit 5f7396ebef.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:11 +02:00
John Crispin 7577f32c8a Revert "ramips: remove conditional compilation."
This reverts commit 1f78625714.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:09 +02:00
John Crispin b8569427eb Revert "ramips: remove unnecessary resource details."
This reverts commit edea934799.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:07 +02:00
John Crispin 784943e3f2 Revert "ramips: pci: sync with staging driver"
This reverts commit e07baec9fa.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:05 +02:00
John Crispin 8a570921b5 Revert "ramips: Add back some non-mt7621 code that staging removed"
This reverts commit 048e41f649.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:03 +02:00
John Crispin 1d3c286381 Revert "ramips: Fix WiFi after 5f7396ebef09b224edf08b0bda113613a42f0928"
This reverts commit 02f815d190.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:41:51 +02:00
Kevin Darbyshire-Bryant 7dca1bae82 kernel: bump to 4.9.105
Refresh patches.

Drop patches that have been upstreamed:
target/linux/ar71xx/patches-4.9/106-01-MIPS-ath79-fix-AR724X_PLL_REG_PCIE_CONFIG-offset.patch
target/linux/generic/backport-4.9/095-v4.12-ipv6-Need-to-export-ipv6_push_frag_opts-for-tunnelin.patch
target/linux/generic/pending-4.9/180-net-phy-at803x-add-support-for-AT8032.patch
target/linux/generic/pending-4.9/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
target/linux/generic/pending-4.9/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch

Compile & run tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-01 08:25:14 +02:00
Alex Maclean 5b0c899bfd ath79: correct wmac names in dts
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-01 08:23:47 +02:00
Alex Maclean ba5b6c619b ath79: add TP-Link TL-WR703N port
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-01 08:23:28 +02:00
Alex Maclean d215d0f9ae ath79: add TP-Link TL-WR740N/ND v2 port
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-01 08:23:14 +02:00
Alex Maclean fab3254b32 ath79: add pinmux node to ar724x.dtsi
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-01 08:23:02 +02:00
Alex Maclean 34f874b872 ath79: add AR7240 dtsi
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-01 08:22:50 +02:00
Alex Maclean fc8360aa16 ath79: add tiny subtarget
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-01 08:22:38 +02:00
John Crispin c57c3f2c22 ath79: fix glinet ar150 lan/wan ordering
LAN and WAN were swapped

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 08:21:47 +02:00
Daniel Golle 2087df1c6d Revert "kernel: backport export ipv6_push_frag_opts for tunneling now"
This reverts commit daa73b63d5.
The fix has already been imported by
commit b7735d8113 ("kernel: import follow-up fix for previous backport").
The patch won't apply twice.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-01 01:37:51 +02:00
Hans Dedecker daa73b63d5 kernel: backport export ipv6_push_frag_opts for tunneling now
Patch is required on top of commit 6c81c27efa as ipv6_push_frag_opts needs to
be exported for usage in ip6_tunnel.c

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-05-31 18:29:42 +02:00
Daniel Golle b7735d8113 kernel: import follow-up fix for previous backport
Buildbots complaining made me wonder what's going on...
ERROR: "ipv6_push_frag_opts" [net/ipv6/ip6_tunnel.ko] undefined!

Fixes: 6c81c27efa ("kernel: backport fix for missing tunnel encapsulation limit option")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-05-31 02:25:59 +02:00
Hans Dedecker 6c81c27efa kernel: backport fix for missing tunnel encapsulation limit option
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-05-30 12:16:24 +02:00
Rosen Penev 9685f39787 ramips: Use generic board detect for GnuBee devices
This is a port of an old commit from mkresin's tree:

09260cdf3e9332978c2a474a58e93a6f2b55f4a8

This has the potential to break sysupgrade but it should be fine as
there is no stable release of LEDE or OpenWrt that support these devices.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-30 06:36:02 +02:00
Rosen Penev 976c27f2dd ramips: Fix a few other GnuBee DTS differences
I was carrying a local commit that added the sdhci stuff and missed it
as a result.

Also fix the rgmii3 thing in the PC2 DTS file as that's bogus and causes
a dmesg warning that it's bogus.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-30 06:35:24 +02:00
Rosen Penev 02f815d190 ramips: Fix WiFi after 5f7396ebef
That commit exposed a bug in the DTS files used by mt7621 where the wrong
reg value for pcie1 (and potentially pcie2) was being used. This was
causing WiFi failures for interfaces in pcie1.

eg. 2.4GHz working but not 5GHz.

As all of these dts entries are already specified in mt7621.dtsi, remove
them.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-30 06:33:56 +02:00