Add initial support for the AArch64 architecture
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43353 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move compatible strings from board structs into separate table. This
allows for several board compatibles to match to the same board in case
e.g. only the flash size / partitions differ.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43341 3c298f89-4303-0410-b956-a3cf2f4a3e73
We should make sure that also for ar8216 hw gets initialized.
For ar8216 hw_init is a dummy currently. The hw_init used for ar8236
should be generic enough to be usable with ar8216 too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43334 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move the PHY fixup call to the PHY init loop.
Use ar8xxx_has_gige in the PHY init instead of passing the gigE
capability via function parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43333 3c298f89-4303-0410-b956-a3cf2f4a3e73
Kernel 3.14 introduced a switch reset in phy_init_hw in drivers/net/phy
causing BMCR_ANENABLE to get cleared.
Due to the fact that ar8xxx_phy_config_aneg does nothing for
PHY 0 autonegatiation support remains disabled.
This can cause ports to operate at 10MBit/half-duplex only.
Fix this by calling genphy_config_aneg for PHY 0 too as
genphy_config_aneg sets BMCR_ANENABLE if it's not yet set.
Fixes: ticket 17800
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43332 3c298f89-4303-0410-b956-a3cf2f4a3e73
PHY init code in the switch-specific hw_init functions is mainly
identical. Factor it out into a generic ar8xxx_phy_init function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43331 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move phy fixup code from the chip-specific hw_init functions into a
fixup_phys callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43330 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently there is a fixed 1000ms wait time after the switch was reset.
Most if not all switches need much less time to perform a reset.
Therefore replace the fixed wait time with polling for BMCR_RESET to
be cleared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43329 3c298f89-4303-0410-b956-a3cf2f4a3e73
All supported switches have 5 PHYs. Currently partially 5 is hardcoded
and partially switch-specific constants exist.
Replace them with a global constant.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43328 3c298f89-4303-0410-b956-a3cf2f4a3e73
wg302v1_fixup() looks for the ATAG_CMDLINE atag, it doesn't find it and
so it takes the last atag in the list and overwrites non allocated
memory.
The side effects are corrupted vital data and a kernel that doesn't
boot. More details here https://dev.openwrt.org/ticket/18356
The fix appends the fixup to the command line and updates the atag only
when it finds it.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43320 3c298f89-4303-0410-b956-a3cf2f4a3e73
Few notes:
- redboot partitions are unusable
- redboot declares only 16M of RAM, hence the mem arg in cmdline and separate kernel config
- boots fine but only ethernet works for now
- split wiliboard and raidsonic boards into different subtargets
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43319 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds 3.14 kernel support for the mpc85xx platform.
Works fine here with a TL-WDR4900 which seems to be the only
supported device using this platform.
There might be differences depending on HW version, therefore
I'd ask others to test too.
Changes to 3.10
missing config options added to 3.14 config file
patch 001: rebased
patch 100: rebased
patch 110: rebased
patch 120: rebased
patch 130: rebased
patch 140: minor adjustment
patch 200: removed, change went upstream
patch 210: rebased
patch 220: removed, change went upstream
patch 750: new, fixes an issue with ethernet port autoneg being
disabled due to changes in kernel phy handling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43308 3c298f89-4303-0410-b956-a3cf2f4a3e73
still no sound but the codec is properly detected now, powers up and i can hear
noise on the speakers.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43305 3c298f89-4303-0410-b956-a3cf2f4a3e73
hardware status and tx vlan offload support on all targets
except rt5350. so i modify the IS_ENABLE condition only for
mt7621.
support mt7621 hardware status reference by SDK. but i don't
have mt7621. if not work just set mt7621 FE_REG_FE_COUNTER_BASE
to 0 to let software count.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43303 3c298f89-4303-0410-b956-a3cf2f4a3e73
hardware tx vlan offload only support max 16 vids
now use add/delete vlan interface to update vlan id table
when duplicate vlan id index detect.
disable hardware tx vlan offload support.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43301 3c298f89-4303-0410-b956-a3cf2f4a3e73
sdhci failed to init because of this
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43293 3c298f89-4303-0410-b956-a3cf2f4a3e73
some old mt7620a uboots dont reset the pcie core properly. work around this
issue in the kernel driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43292 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without this patch the UBIFS driver is unable to attach to the mtd
storage and mount the root FS.
Fixes a kernel panic with Netgear WNDR4300/3700v4 devices.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43287 3c298f89-4303-0410-b956-a3cf2f4a3e73
Sets the system LED on the EasyLink M150 and mini to lower-case "easylink"
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43271 3c298f89-4303-0410-b956-a3cf2f4a3e73
this makes gpio-poweroff work
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43254 3c298f89-4303-0410-b956-a3cf2f4a3e73
the new driver handles newer SoCs
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43250 3c298f89-4303-0410-b956-a3cf2f4a3e73
a missing "val =" caused the AN bit in the phy0 reg to be flushed.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43246 3c298f89-4303-0410-b956-a3cf2f4a3e73
the SDK does a bit of extra init that we did not do yet when using an external mt7530.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43245 3c298f89-4303-0410-b956-a3cf2f4a3e73
somehow all switch ports still come up as 10mbit.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43237 3c298f89-4303-0410-b956-a3cf2f4a3e73
make 1166 wan port work. this broke due to the esw_polling bug
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43236 3c298f89-4303-0410-b956-a3cf2f4a3e73
this driver confuses some boards
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43234 3c298f89-4303-0410-b956-a3cf2f4a3e73
Camera has microphone; in order to use it by default enable sound support.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43232 3c298f89-4303-0410-b956-a3cf2f4a3e73
* read MAC address from factory partition
* remove port defines since there is only one port (most likely C/P error)
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43231 3c298f89-4303-0410-b956-a3cf2f4a3e73
i accidentally dropped 2 lines while adding mt7628 support
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43216 3c298f89-4303-0410-b956-a3cf2f4a3e73
r43200 tries to detect if the fixup is needed or not. control the behaviour via
OF instead and disable unused ports.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43201 3c298f89-4303-0410-b956-a3cf2f4a3e73
this broke e1700 lan2 as the fixup was applied to the phy inside the mt7530.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43200 3c298f89-4303-0410-b956-a3cf2f4a3e73
the current driver code wont know which mt7530 to apply the llllw setting to.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43199 3c298f89-4303-0410-b956-a3cf2f4a3e73
Florian Fainelli
Felix Fietkau
Jonas Gorski
Zoltan HERPAI
Rafał Miłecki
John Crispin
Luka Perkov
Hauke Mehrtens
Nicolas Thill
Imre Kaloz
Steven Barth