[ramips]: add support for the Linksys E1700

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43186 3c298f89-4303-0410-b956-a3cf2f4a3e73

target/linux/ramips/base-files/etc/board.d/02_network

@@ -221,6 +221,7 @@ ramips_setup_interfaces()
 		ucidef_set_interface_lan "eth0"
 		;;
 
+	e1700 | \
 	mt7620a_mt7530)
 		ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
 		ucidef_add_switch "switch1" "1" "1"
@@ -302,6 +303,10 @@ ramips_setup_macs()
 		wan_mac=$(mtd_get_mac_ascii nvram wanmac)
 		;;
 
+	e1700)
+		wan_mac=$(mtd_get_mac_ascii config WAN_MAC_ADDR)
+		;;
+
 	wcr-150gn)
                 wan_mac=$(mtd_get_mac_binary factory 40)
 		;;

target/linux/ramips/base-files/etc/diag.sh

@@ -48,6 +48,9 @@ get_status_led() {
 	dap-1350)
 		status_led="d-link:blue:power"
 		;;
+	e1700)
+		status_led="linksys:green:power"
+		;;
 	esr-9753)
 		status_led="esr-9753:orange:power"
 		;;

target/linux/ramips/base-files/lib/ramips.sh

@@ -175,6 +175,9 @@ ramips_board_detect() {
 	*"Kingston MLW221")
 		name="mlw221"
 		;;
+	*"Linksys E1700")
+		name="e1700"
+		;;
 	*"Planex MZK-750DHP")
 		name="mzk-750dhp"
 		;;

target/linux/ramips/base-files/lib/upgrade/platform.sh

@@ -44,6 +44,7 @@ platform_check_image() {
 	dir-620-a1 | \
 	dir-620-d1 | \
 	dir-810l | \
+	e1700 | \
 	esr-9753 | \
 	f7c027 | \
 	fonera20n | \

target/linux/ramips/dts/E1700.dts

@@ -0,0 +1,148 @@
+/*
+ * Device Tree file for the Linksys E1700
+ *
+ * Copyright (C) 2014 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+	compatible = "linksys,e1700", "ralink,mt7620a-soc";
+	model = "Linksys E1700";
+
+	palmbus@10000000 {
+		spi@b00 {
+			status = "okay";
+
+			m25p80@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "mx25l6405d";
+				reg = <0 0>;
+				linux,modalias = "m25p80", "mx25l6405d";
+				spi-max-frequency = <10000000>;
+
+				partition@0 {
+					label = "u-boot";
+					reg = <0x0 0x30000>;
+					read-only;
+				};
+
+				partition@30000 {
+					label = "config";
+					reg = <0x30000 0x10000>;
+					read-only;
+				};
+
+				factory: partition@40000 {
+					label = "factory";
+					reg = <0x40000 0x10000>;
+					read-only;
+				};
+
+				partition@50000 {
+					label = "firmware";
+					reg = <0x50000 0x7b0000>;
+				};
+			};
+		};
+	};
+
+	pinctrl {
+		state_default: pinctrl0 {
+			gpio {
+				ralink,group = "i2c", "uartf";
+				ralink,function = "gpio";
+			};
+		};
+	};
+
+	ethernet@10100000 {
+		status = "okay";
+
+		mtd-mac-address = <&factory 0x28>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;
+
+		ralink,port-map = "llllw";
+
+		port@5 {
+			status = "okay";
+			ralink,fixed-link = <1000 1 1 1>;
+			phy-mode = "rgmii";
+		};
+
+		mdio-bus {
+			status = "okay";
+
+			phy0: ethernet-phy@0 {
+				reg = <0>;
+				phy-mode = "rgmii";
+			};
+			phy1: ethernet-phy@1 {
+				reg = <1>;
+				phy-mode = "rgmii";
+			};
+			phy2: ethernet-phy@2 {
+				reg = <2>;
+				phy-mode = "rgmii";
+			};
+			phy3: ethernet-phy@3 {
+				reg = <3>;
+				phy-mode = "rgmii";
+			};
+			phy4: ethernet-phy@4 {
+				reg = <4>;
+				phy-mode = "rgmii";
+			};
+			phy1f: ethernet-phy@1f {
+				reg = <0x1f>;
+				phy-mode = "rgmii";
+			};
+		};
+	};
+
+	gsw@10110000 {
+		ralink,port4 = "gmac";
+	};
+
+	wmac@10180000 {
+		ralink,mtd-eeprom = <&factory 0>;
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+		reset {
+			label = "reset";
+			gpios = <&gpio0 1 0>;
+			linux,code = <0x198>;
+		};
+		wps {
+			label = "wps";
+			gpios = <&gpio0 2 0>;
+			linux,code = <0x211>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		power {
+			label = "linksys:green:power";
+			gpios = <&gpio0 10 1>;
+		};
+		wan {
+			label = "linksys:green:wps";
+			gpios = <&gpio0 12 1>;
+		};
+	};
+};

target/linux/ramips/image/Makefile

@@ -772,6 +772,7 @@ endif
 # MT7620A Profiles
 #
 
+Image/Build/Profile/E1700=$(call BuildFirmware/UMedia/$(1),$(1),e1700,E1700,0x013326)
 Image/Build/Profile/MT7620a=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a,MT7620a)
 Image/Build/Profile/MT7620a_MT7610e=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a_mt7610e,MT7620a_MT7610e)
 Image/Build/Profile/MT7620a_MT7530=$(call BuildFirmware/Default8M/$(1),$(1),mt7620a_mt7530,MT7620a_MT7530)
@@ -792,6 +793,7 @@ Image/Build/Profile/Y1S=$(call BuildFirmware/Default16M/$(1),$(1),Lenovo-y1s,Y1S
 
 ifeq ($(SUBTARGET),mt7620a)
 define Image/Build/Profile/Default
+	$(call Image/Build/Profile/E1700,$(1))
 	$(call Image/Build/Profile/MT7620a,$(1))
 	$(call Image/Build/Profile/MT7620a_MT7610e,$(1))
 	$(call Image/Build/Profile/MT7620a_MT7530,$(1))

target/linux/ramips/mt7620a/profiles/linksys.mk

@@ -0,0 +1,16 @@
+#
+# Copyright (C) 2014 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/E1700
+	NAME:=Linksys E1700
+	PACKAGES:=swconfig
+endef
+
+define Profile/E1700/Description
+	Package set compatible with the Linksys E1700.
+endef
+$(eval $(call Profile,E1700))