f8386ecbc6
cleanup image generation
...
SVN-Revision: 33065
2012-08-08 21:50:55 +00:00
64b385dda7
pci gpio mapping
...
This patch fixes the GPIO ALTSEL settings for some of the GPIOs used by the PCI subsystem in Lantiq Danube. These changes are required for more than one PCI device to work. Tested with an ARV7510PW having two PCI-devices; a VIA USB controller and a Ralink WLAN mini-PCI card.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 33054
2012-08-08 12:14:43 +00:00
4feeda756e
bcm63xx: fix USB base registers and IRQs for BCM6328
...
SVN-Revision: 33005
2012-08-05 23:18:22 +00:00
a0fb060211
update tg3 driver
...
SVN-Revision: 33004
2012-08-05 20:27:40 +00:00
35661401da
generate image for Linksys e3200
...
SVN-Revision: 33003
2012-08-05 13:14:00 +00:00
a71f347c30
brcm47xx: update gpio patch
...
SVN-Revision: 33001
2012-08-05 12:40:05 +00:00
1d40a652ee
brcm47xx: fix patch which moves the flash struct in wgt634u code
...
SVN-Revision: 33000
2012-08-05 12:39:15 +00:00
5f438c3565
W502V/ARV4525 wireless mac bugfix
...
The ARV4525 board init is passing the wrong offset to
arv_register_ath5k() resulting in a bogus mac.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 32993
2012-08-04 20:14:52 +00:00
0758996824
brcm47xx: use libgpio instaed of implementing the gpio interface ourself.
...
SVN-Revision: 32992
2012-08-04 19:46:25 +00:00
060b161ca6
cleanup patches
...
SVN-Revision: 32953
2012-08-03 08:53:02 +00:00
162e272b4b
nuport-mac: properly protect the phy interrupt handler
...
SVN-Revision: 32951
2012-08-02 18:13:17 +00:00
f45132d1d4
Codel: avoid a nul rec_inv_sqrt
...
One condition before codel_Newton_step() was not good if
we never left the dropping state for a flow. As a result
rec_inv_sqrt was 0, instead of the ~0 initial value.
codel control law was then set to a very aggressive mode, dropping
many packets before reaching 'target' and recovering from this problem.
Brought over from 3.5-stable
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
SVN-Revision: 32950
2012-08-02 13:39:50 +00:00
c2d3274ffc
fixes i2c clock enable
...
SVN-Revision: 32949
2012-08-02 13:29:49 +00:00
e320a7e649
ar71xx: simplify misc IRQ handling
...
SVN-Revision: 32948
2012-08-02 11:25:49 +00:00
3e1e52a524
ar71xx: fix AR934X_EHCI_SIZE
...
SVN-Revision: 32947
2012-08-02 11:25:46 +00:00
b873051706
ar71xx: image: stop the switch from the lzma-loader on the TL-WR1043ND
...
SVN-Revision: 32946
2012-08-02 09:54:41 +00:00
e29d6bec6f
ar71xx: image: allow to use board specific code in the lzma-loader
...
SVN-Revision: 32945
2012-08-02 09:54:33 +00:00
79a8660d67
ar71xx: init switch hw_reset on the TL-WR1043ND board
...
SVN-Revision: 32944
2012-08-02 09:54:28 +00:00
e2782eae8e
generic: rtl836x: add hw_reset field to struct rtl8366_smi
...
It will be used to start/stop the switch if that is
supported by the given board.
SVN-Revision: 32943
2012-08-02 09:54:21 +00:00
614ca3cc9e
generic: rtl8366_smi: use __rtl8366_smi_cleanup instead of gpio_free calls
...
SVN-Revision: 32942
2012-08-02 09:54:13 +00:00
9f011e7225
add missing netmask to the network config
...
SVN-Revision: 32941
2012-08-01 22:09:13 +00:00
5133a44785
assume the link is up and full-duplex by default
...
SVN-Revision: 32940
2012-08-01 21:56:54 +00:00
56aac45139
add a default and suitable network config file
...
SVN-Revision: 32939
2012-08-01 21:56:49 +00:00
563400ef10
ar71xx: ew-dorin: added router firmware generation
...
[juhosg: remove dead code]
Signed-off-by: embedded wireless GmbH <info@embeddedwireless.de>
SVN-Revision: 32934
2012-08-01 12:24:57 +00:00
8eabe64e6b
ar71xx: ew-dorin: added USB support
...
Signed-off-by: embedded wireless GmbH <info@embeddedwireless.de>
SVN-Revision: 32933
2012-08-01 12:24:56 +00:00
1af4fd7660
ar71xx: Buffalo WLAE-AG300N wireless led patch
...
Here is the uci-defaults version of the led support for
the Buffalo WLAE-AG300N.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32932
2012-08-01 12:24:54 +00:00
010aec0619
ar71xx: Buffalo WLAE-AG300N initial support
...
The patch set for Buffalo WLAE-AG300N initial support.
There is another patch for wireless led support that
is posted separately.
Note on serial console:
This unit has buffalo standard 4 pin console, but the unit may not power
on if some console apparatus is connected. This is probably due to some
electronic interaction between the unit's electronic power switch circuit
and the serial console apparatus. If this happens, it is required to power
on the unit without the console, then quickly (re-)attach it.
[juhosg: fix coding style]
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32931
2012-08-01 12:24:52 +00:00
df48d71d72
resync defconfig enable XZ compression
...
SVN-Revision: 32930
2012-08-01 12:01:27 +00:00
3cd753408d
properly generate squashfs, jffs2 and initramfs images and kernels
...
SVN-Revision: 32927
2012-07-31 23:09:50 +00:00
c0561a42e7
disable crashlog on ARM platforms for the moment
...
It is currently badly broken on ARM, until fixed, disable it
SVN-Revision: 32926
2012-07-31 23:09:46 +00:00
f5f36911f0
add lantiq svip support
...
SVN-Revision: 32925
2012-07-31 18:49:54 +00:00
07c4524d33
bcm63xx: Add nb6 support (BCM6362 SoC base boards)
...
Signed-off-by: Miguel GAIO <miguel.gaio@efixo.com>
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
[jonas.gorski@gmail.com: add network config for nb6, make switch fix a
platform patch]
SVN-Revision: 32924
2012-07-31 14:27:47 +00:00
820c224029
bcm63xx: add basic bcm6362 support
...
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32923
2012-07-31 14:27:42 +00:00
dcd339ac9d
bcm63xx: enable usb for bcm6328
...
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32922
2012-07-31 14:27:34 +00:00
94d257a851
bcm63xx: update enetswitch driver
...
Update enetswith driver with latest fixes and additions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32921
2012-07-31 14:27:31 +00:00
fa75bd977a
bcm63xx: reorder patches
...
Fix the order and names of patches.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32920
2012-07-31 14:27:25 +00:00
d1ab4df0d6
move i2c module to target modules.mk
...
SVN-Revision: 32910
2012-07-29 13:20:51 +00:00
a5738c960a
resync config
...
SVN-Revision: 32908
2012-07-29 13:20:39 +00:00
17244dea00
use the same description as other omap platforms (without the dash)
...
SVN-Revision: 32907
2012-07-29 13:20:35 +00:00
ee0946a5f4
refresh pwm patch
...
SVN-Revision: 32905
2012-07-29 11:53:06 +00:00
101766fb00
clean up pwm patches and drivers
...
SVN-Revision: 32901
2012-07-28 20:47:08 +00:00
f0fe59648a
add config option CONFIG_I2C_MV64XXX to fix kirkwood build
...
SVN-Revision: 32898
2012-07-28 11:36:52 +00:00
67891c26ec
resync config
...
SVN-Revision: 32895
2012-07-27 15:35:15 +00:00
a4d699ccf0
fix DVA-G3810BN image generation
...
Attached patch fixes a typo in the image Makefile, and overrides the
board name for DVA-G3810BN to set the correct board properties
Signed-Off-By: Jeroen van Bemmel <jbemmel@zonnet.nl>
SVN-Revision: 32894
2012-07-27 15:35:12 +00:00
c6813d33f3
add D-link DVA-G3810BN-TL-1 support
...
Signed-Off-By: Jeroen van Bemmel <jbemmel@zonnet.nl>
SVN-Revision: 32893
2012-07-27 15:35:09 +00:00
18206793b2
Add CT6376-1 board support
...
Added CT6373 devices instead of using NB4's devices, as Florian suggested.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 32892
2012-07-27 15:35:05 +00:00
4acdbb1d87
Add brcmsmac profile
...
Add brcmsmac profile (kmod-brcmsmac + wpad-mini).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 32890
2012-07-27 15:34:57 +00:00
0ba7b18cfd
Add leds back after migration to sysfs
...
atheros trunk moved to full sysfs gpiolib, but the leds were forgotten.
This restores the wlan led that was missing after switching from backfire
to trunk.
Signed-off-by: Karl Palsson <karlp@remake.is>
SVN-Revision: 32885
2012-07-26 17:06:55 +00:00
46611b2cbf
add more missing config symbols
...
SVN-Revision: 32884
2012-07-26 17:03:08 +00:00
ac30beaaa7
add more USB-related config symbols
...
SVN-Revision: 32883
2012-07-26 17:03:05 +00:00
a077e785cf
make sure target modules depend on the target
...
SVN-Revision: 32882
2012-07-26 17:03:02 +00:00
0c75abf527
bcma: update to version from wireless-testing tag master-2012-07-16
...
I did not add the last patch, because it add some stubs for the flash drivers and our patches have to be changed for that, if the flash support in bcma is able to do something I will integrate it.
This also contains 3 additional patches fixing some bugs in bcma.
SVN-Revision: 32880
2012-07-26 15:42:18 +00:00
87a72d68f1
fix typo in modules.mk
...
This patch fixes a small typo in kmod-leds-wndr3700-usb description, where the board is for some reason made by NETGWR, not NETGEAR.
Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
SVN-Revision: 32870
2012-07-25 19:52:30 +00:00
d359d46182
make kmod-fb dependent on DISPLAY_SUPPORT and update targets accordingly
...
SVN-Revision: 32869
2012-07-25 19:36:19 +00:00
adc2b21be8
move isp116x driver to target specific modules.mk
...
SVN-Revision: 32865
2012-07-25 15:50:45 +00:00
1627b2bb4b
move rt305x-dwc driver to target specific modules.mk
...
SVN-Revision: 32864
2012-07-25 15:50:42 +00:00
c7a69869f7
move ubsec-ssb driver to target specific modules.mk
...
SVN-Revision: 32863
2012-07-25 15:50:38 +00:00
d1b2087a35
move ssb-gige to target specific modules.mk
...
SVN-Revision: 32862
2012-07-25 15:50:36 +00:00
c14d907b8b
move usb driver to target specific modules.mk
...
SVN-Revision: 32861
2012-07-25 15:50:33 +00:00
3b5a8548f4
move mmc driver to target specific modules.mk
...
SVN-Revision: 32859
2012-07-25 15:50:26 +00:00
18038c803c
move ixp4xx-eth to target specific modules.mk
...
SVN-Revision: 32858
2012-07-25 15:50:23 +00:00
4000de357e
move crypto module to target specific modules.mk
...
SVN-Revision: 32856
2012-07-25 15:50:16 +00:00
a282e37c09
move i2c driver to target modules.mk
...
SVN-Revision: 32855
2012-07-25 15:50:13 +00:00
accbc20045
move watchdog driver to target specific modules.mk
...
SVN-Revision: 32854
2012-07-25 15:50:10 +00:00
23ffbad602
move target specific spi modules
...
SVN-Revision: 32853
2012-07-25 15:50:04 +00:00
1859500829
move target specific leds modules to ar71xx modules.mk
...
SVN-Revision: 32852
2012-07-25 15:50:02 +00:00
c3b9a987b7
move leds modules back to target modules.mk
...
SVN-Revision: 32851
2012-07-25 15:49:57 +00:00
bca45d6d8a
move i2c modules back to target modules.mk
...
SVN-Revision: 32850
2012-07-25 15:49:54 +00:00
2bfb2a797c
move more x86-specific modules back to target modules.mk
...
SVN-Revision: 32848
2012-07-25 15:49:49 +00:00
d973768580
move x86 specific ide/pata modules to x86' modules.mk
...
SVN-Revision: 32846
2012-07-25 15:49:42 +00:00
e0837a51f0
brcm47xx: reorder patches so that the patches already in mainline linux will be applied at first.
...
SVN-Revision: 32845
2012-07-25 14:52:00 +00:00
ab2cb9ce61
add yet another framebuffer symbol
...
SVN-Revision: 32844
2012-07-25 14:01:57 +00:00
89a312bf48
split framebuffer helper modules to their own packages
...
SVN-Revision: 32843
2012-07-25 14:01:54 +00:00
ba9f6a46b1
remove broken flag
...
SVN-Revision: 32842
2012-07-25 14:01:51 +00:00
03c06178e3
package buttons driver separately
...
SVN-Revision: 32841
2012-07-25 14:01:49 +00:00
83b7462ac9
package cobalt lcd as a module
...
SVN-Revision: 32840
2012-07-25 14:01:46 +00:00
7ee4798be2
add unset CONFIG_FB_XGI to fix fullbuilds
...
SVN-Revision: 32836
2012-07-25 09:05:23 +00:00
94a550cc87
cleanup config-3.3, remove =m
...
SVN-Revision: 32835
2012-07-25 09:05:18 +00:00
1cbfa0c0f5
laguna: fix eeprom read buffer size during platform configuration
...
Increase the size of the buffer used for eeprom reads during the platform configuration of the Gateworks laguna. The model name read in is 16 bytes but the original buffer was only 8 bytes.
Signed-off-by: David Acker <dacker@rajant.com>
SVN-Revision: 32833
2012-07-25 08:01:38 +00:00
0e9e7dcd10
adds target used by rapsberry pi
...
Add support for Raspberry Pi / brcm2708 / 2835
Signed-off-by: Ian Ridge <ianridge [at] gmail.com>
SVN-Revision: 32825
2012-07-24 20:39:17 +00:00
5e52619b76
DWC otg usb: compilation fixes and trivial bugfix in slave mode
...
Signed-of-by: Nikolai Zhubr <n-a-zhubr@yandex.ru>
SVN-Revision: 32823
2012-07-24 20:38:55 +00:00
799d6deab0
D-Link DAP-1350 initial support
...
The initial support for the D-Link DAP-1350.
USB related functionality is not tested.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32821
2012-07-24 20:38:43 +00:00
b891eec700
MI424WR - add rev D support
...
Add support for revision D of the MI424WR.
Rev D swaps LAN & WAN ports so this patch maintains
eth0 for LAN and eth1 for WAN. For details on rev D usage,
see http://wiki.openwrt.org/toh/actiontec/mi424wr
Signed-off-by: Jose Vasconcellos <jvasco@verizon.net>
SVN-Revision: 32820
2012-07-24 20:38:36 +00:00
03be8d08ac
initial LED configuration for Fonera 2.0n
...
Setup initial configuration for Wifi and USB LEDS of a Fonera 2.0n (ramips)
Signed-off-by: Malte Forkel <malte.forkel@berlin.de>
SVN-Revision: 32819
2012-07-24 20:38:31 +00:00
2d2479a033
add ALL5002 userspace support
...
detect EEPROM, MAC addresses and support sysupgrade for the ALL5002
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32816
2012-07-24 20:38:14 +00:00
e219c3ac3a
enable OHCI/EHCI glue on Rt305x, so it is available for Rt3352F.
...
Hope that this works, didn't have a chance to actually test it...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32815
2012-07-24 20:38:08 +00:00
a65eee9ac3
add image build for ALL5002
...
add image build for ALL5002
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32814
2012-07-24 20:38:03 +00:00
0a08a776fb
add support for Allnet ALL5002 to kernel
...
support ALL5002 in ramips/rt305x branch of the kernel.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32813
2012-07-24 20:37:56 +00:00
6641024f50
uart_clk on Rt3352F is always 40MHz
...
Currently, sys_clk/10 is used which is just wrong.
cpu_clk/10 would work for systems with 400MHz CPU clock.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32812
2012-07-24 20:37:50 +00:00
93dc8c8d1b
move omap specific modules to modules.mk
...
SVN-Revision: 32810
2012-07-24 19:43:54 +00:00
82c7e05d42
move n810 battery module to omap24 modules.mk
...
SVN-Revision: 32809
2012-07-24 19:43:49 +00:00
25e20b0b57
move target specific modules to target's module.mk
...
SVN-Revision: 32808
2012-07-24 19:43:45 +00:00
587f85ac20
package ep93xx framebuffer
...
SVN-Revision: 32807
2012-07-24 19:43:35 +00:00
5915c85d80
remove crypto symbols override
...
SVN-Revision: 32806
2012-07-24 19:43:31 +00:00
c238862651
add missing framebuffer related symbols
...
SVN-Revision: 32804
2012-07-24 19:43:23 +00:00
9f55e6f954
remove broken flag, since it works
...
SVN-Revision: 32803
2012-07-24 19:43:19 +00:00
c531ce0301
fix sound modules loading order and dependencies
...
SVN-Revision: 32802
2012-07-24 19:43:15 +00:00
598ef2a2e0
package ep93xx touchscreen driver as a module
...
SVN-Revision: 32799
2012-07-24 19:42:49 +00:00
0db5f35846
set DEVICE_TYPE to developerboard
...
SVN-Revision: 32798
2012-07-24 19:42:44 +00:00
5178c177dc
rebase config-3.3
...
SVN-Revision: 32797
2012-07-24 17:28:25 +00:00
53a6946bb4
fix tantos patch properly
...
SVN-Revision: 32796
2012-07-24 17:28:12 +00:00
6fe32d72a2
make tantos switch select ETHERNET_PACKET_MANGLE
...
SVN-Revision: 32795
2012-07-24 16:50:14 +00:00
48869ef7c0
move CONFIG_ETHERNET_PACKET_MANGLE to a generic config file
...
This broke falcon builds
SVN-Revision: 32794
2012-07-24 15:33:01 +00:00
b59bc92c6e
crashlog: fix dependency, add memblock support
...
SVN-Revision: 32787
2012-07-22 16:39:33 +00:00
b1f318de53
kernel: fix portability issues on the x86 specific relocs host tool, fixes build on mac os x
...
SVN-Revision: 32783
2012-07-20 12:28:50 +00:00
05340cc602
rename upgrade image to sysupgrade.bin for consistency
...
SVN-Revision: 32770
2012-07-17 16:47:57 +00:00
d243c1e1f2
add missing configuration symbols
...
SVN-Revision: 32769
2012-07-17 16:40:28 +00:00
f7dfd20f97
au1000: implement sysupgrade platform.sh
...
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 32768
2012-07-17 16:40:24 +00:00
ac6bf6d62f
au1000: clean up profiles
...
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 32767
2012-07-17 16:39:52 +00:00
b2d76e1e05
au1000: fix InternetBox idsel and remove broken flag
...
The following patch is necessary for the InternetBox (Surfbox) board-specific
idsel to work with newer kernels. Acutally I don't exactly understand why this
was not necessary before, but without the udelay, the MiniPCI adapter in slot 3
is not detected and set up correctly.
Also remove platform broken flag, it works.
Signed-off-by: Bruno Randolf <br1@einfach.org>
SVN-Revision: 32766
2012-07-17 16:39:47 +00:00
21de1b9d85
ar71xx: enable I2C_GPIO, the PB44 board needs that
...
SVN-Revision: 32738
2012-07-15 17:52:52 +00:00
7daf851adf
ar71xx: fix PB44 board detection
...
SVN-Revision: 32737
2012-07-15 17:52:50 +00:00
c7fa38484c
ar71xx: use gpio_set_value_cansleep on sleeping GPIOs in ath79_spi
...
SVN-Revision: 32736
2012-07-15 17:52:48 +00:00
03a6d65c37
kernel: add Marvell SoC built-in RTC to modules
...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32732
2012-07-15 14:25:30 +00:00
c727c2aacf
set DEVICE_TYPE to other to avoid pulling unecessary packages
...
SVN-Revision: 32731
2012-07-15 14:10:03 +00:00
a5d72815b5
add compatible property to pci node
...
SVN-Revision: 32730
2012-07-15 14:09:40 +00:00
b5578d83d5
use ohci_err() instead of err()
...
SVN-Revision: 32729
2012-07-15 14:09:32 +00:00
0e0b396663
make sure we properly unmap DMA mappings we created
...
SVN-Revision: 32728
2012-07-15 14:09:24 +00:00
0f0e42f28e
nuport-mac: add definitions of the various bits/masks used
...
SVN-Revision: 32727
2012-07-15 14:09:18 +00:00
c89e87d186
kirkwood: add support for seagate goflexnet and goflexhome
...
Signed-off-by: Martin Mueller <mm@sig21.net>
SVN-Revision: 32725
2012-07-15 12:18:29 +00:00
952ce3473d
kirkwood: revert config changes from r32053
...
SVN-Revision: 32719
2012-07-15 00:08:52 +00:00
33220828dc
ar71xx: build firmware image for the TP-Link TL-WDR4310 v1.0
...
The hardware for TP-Link TL-WDR4300 v1.1 and TL-WDR4310 v1.0 is
identical, but requires different firmware headers:
TL-WDR4300:
00000040 43 00 00 01 00 00 00 01 00 00 00 00 76 fb 83 40 |C...........v..@|
TL-WDR4310:
00000040 43 10 00 01 00 00 00 01 00 00 00 00 38 2b 50 6c |C...........8+Pl|
[juhosg: change commit message, use a different model name]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
SVN-Revision: 32683
2012-07-12 13:38:40 +00:00
372945185d
ramips: rt305x: add support for Edimax 3G-6200N
...
Support for Edimax 3G-6200N router with USB.
Signed-off-by: Lukasz Golebiowski <lgolebio@gmail.com>
SVN-Revision: 32682
2012-07-12 13:29:46 +00:00
e9af340016
generic: ocf: restore terminating entry of pci_id_table in hifnHIPP
...
SVN-Revision: 32680
2012-07-12 08:34:23 +00:00
d3c8852fd1
ar71xx: select ATH79_DEV_M25P80 for the WRT400N board
...
SVN-Revision: 32679
2012-07-12 08:34:22 +00:00
c75c895d24
ar71xx: airrouter power led support
...
This patch adds support for power led to Unifi Airrouter AP.
[juhosg:fold the patch into 608-MIPS-ath79-ubnt-xm-add-more-boards.patch]
Signed-off-by: Rocco Folino <lordzen@autistici.org>
SVN-Revision: 32678
2012-07-12 08:34:21 +00:00
466f010303
ar71xx: unifi reset button support
...
This patch adds support for reset button to Ubiquiti UniFi AP.
[juhosg: fold the patch into 608-MIPS-ath79-ubnt-xm-add-more-boards.patch]
Signed-off-by: Rocco Folino <lordzen@autistici.org>
SVN-Revision: 32677
2012-07-12 08:34:20 +00:00
5ce9c90ca8
ar71xx: airrouter reset button support
...
This patch adds support for reset button to Ubiquiti Airrouter AP.
[juhosg: fold the patch into 608-MIPS-ath79-ubnt-xm-add-more-boards.patch]
Signed-off-by: Rocco Folino <lordzen@autistici.org>
SVN-Revision: 32676
2012-07-12 08:34:18 +00:00
283021ac15
ocf: update to version 20120127
...
SVN-Revision: 32672
2012-07-11 23:38:14 +00:00
45d55161a6
kernel: bcma: update to version from wireless-testing tag master-2012-07-11
...
SVN-Revision: 32670
2012-07-11 22:17:05 +00:00
b94d9eb302
remove bcm63xx_pci_register() call in livebox board
...
SVN-Revision: 32661
2012-07-11 09:15:26 +00:00
f8446c3d4c
use physmap-flash on livebox ( #8677 )
...
SVN-Revision: 32660
2012-07-11 09:15:22 +00:00
8765e49fbe
nuport-mac: check netif_receive_skb() return value
...
We did not reassign status to netif_receive_skb() return value, we thus
almost always incremented the dropped counter because the descriptor status
value never matches the NET_RX_DROP.
SVN-Revision: 32659
2012-07-11 08:29:01 +00:00
93bf00ff36
fix typo on of_node_put()
...
SVN-Revision: 32653
2012-07-09 14:44:15 +00:00
bb1488e5e7
Detect alternative "cfe-" version bootloaders (found in 963281T_TEF board)
...
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 32643
2012-07-06 22:10:37 +00:00
fe015f399f
ar71xx: swizzle address for PCI byte/word access on AR71xx
...
Closes #11683 .
SVN-Revision: 32639
2012-07-06 16:33:12 +00:00
b39df5bb81
ar71xx: select SOC_AR933X and ATH79_DEV_WMAC for the OM2P board
...
SVN-Revision: 32638
2012-07-06 11:12:02 +00:00
e258367c19
ar71xx: merge new board patches into the generic patch
...
SVN-Revision: 32637
2012-07-06 11:12:01 +00:00
b020a7e7c3
ar71xx: OM2P LC sysupgrade patch
...
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
SVN-Revision: 32635
2012-07-06 11:11:58 +00:00
110fd3525a
call of_node_put() on ethernet node
...
SVN-Revision: 32628
2012-07-05 18:46:55 +00:00
a8fab2cb78
fix EPHY clock bit definition after r32489
...
SVN-Revision: 32627
2012-07-05 18:46:52 +00:00
81681d7367
give an unique partition identifier for dLAN USB Extender Combined partition
...
SVN-Revision: 32626
2012-07-05 18:46:48 +00:00
eabf96dc22
ar71xx: set firmware version for the TL-WR2543N
...
This ensures that the resulting firmware can
be flashed from the latest (v3.13.17) offical
firmware.
SVN-Revision: 32617
2012-07-05 16:25:31 +00:00
7c932579fa
ar71xx: make 2.4GHz wlan LED work on the WR2543N
...
Because ath9k does not supports separate LEDs for
different bands yet, the 2.4GHz LED will show the
activity, even if the 5GHz band is selected.
SVN-Revision: 32615
2012-07-05 16:25:26 +00:00
b2f0476871
ar71xx: OM2P sysupgrade support
...
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
SVN-Revision: 32613
2012-07-05 08:26:57 +00:00
797944d3f1
ar71xx: add support for the OpenMesh OM2P-LC board
...
Patch-by: Marek Linder <marek@open-mesh.com>
SVN-Revision: 32611
2012-07-05 08:26:53 +00:00
1ea2a3cfd8
ar71xx: add profile and build image for the Atheros AP136 reference board
...
SVN-Revision: 32609
2012-07-05 08:26:51 +00:00
b219848bfc
ar71xx: AP136 user-space support
...
SVN-Revision: 32608
2012-07-05 08:26:50 +00:00
f0cda65bb6
ar71xx: add initial support for the Qualcomm Atheros AP136 board
...
SVN-Revision: 32607
2012-07-05 08:26:48 +00:00
d1b237b335
ar71xx: add initial support for the QCA955X SoCs
...
SVN-Revision: 32606
2012-07-05 08:26:47 +00:00
7284cf73d6
ar71xx: refactor PCI code to allow registering multiple PCI controllers
...
SVN-Revision: 32605
2012-07-05 08:26:45 +00:00
6b8392eb12
generic: ar8216: start aneg on each PHY of the AR8327
...
SVN-Revision: 32604
2012-07-05 08:26:39 +00:00
0fdac1102d
add missing interrupts properties to some device nodes
...
SVN-Revision: 32603
2012-07-04 19:37:11 +00:00
bfef2d17eb
ar71xx: update the EW Dorin MTD layout, increase kernel partition size (requested by EW)
...
SVN-Revision: 32599
2012-07-04 10:55:56 +00:00
0a3e9c3148
bcm63xx: bcm63xx-spi does not depend on spi-bitbang
...
SVN-Revision: 32594
2012-07-03 21:42:17 +00:00
fad888a85c
bcm63xx: 96348A-122 improvements (Comtrend 5365)
...
1) Improve WLAN button.
2) Add 96348A-122 image.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 32593
2012-07-03 21:42:15 +00:00
0c7e676342
bcm63xx: fix second caldata address calculation
...
thanks Noltari for spotting this.
SVN-Revision: 32592
2012-07-03 21:42:12 +00:00
988147111c
bcm63xx: update patches to latest upstream versions
...
SVN-Revision: 32591
2012-07-03 21:42:07 +00:00
1e2262df76
kernel: generic: spi: allow empty (un)prepare transfer
...
SVN-Revision: 32590
2012-07-03 21:42:03 +00:00
b8618fd3f2
ar71xx: improve MDIO busy wait code
...
SVN-Revision: 32586
2012-07-03 15:24:02 +00:00
86013d40d5
ar71xx: remove the built-in MTD map of the ALL0258N
...
Pass the mtd_layout via the kernel command line instead.
Also increase the kernel partition size to 1024k, so current kernel can fit in.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32585
2012-07-03 15:24:01 +00:00
4cdc4b1f36
refresh patches
...
SVN-Revision: 32581
2012-07-03 09:45:46 +00:00
bd9fa13c73
kernel: ssb/bcma: update to version from wireless-testing tag master-2012-07-02
...
SVN-Revision: 32580
2012-07-02 23:12:58 +00:00
52bae2d2bd
fix watchdog and rng drivers section mismatch ( #11767 )
...
SVN-Revision: 32522
2012-06-29 09:07:54 +00:00
5570b76642
ar71xx: detect and enable MIPS DSP extensions, AR9344 supports them ( fixes #11762 )
...
SVN-Revision: 32520
2012-06-28 16:05:08 +00:00
a5c684de26
kernel: switch openwrt default to TCP cubic from westwood (patch by Dave Täht)
...
Despite Westwood's theoretical advantages, in nearly
every benchmark we ran last year, TCP cubic won, whether it be
on correct RTT estimates, amount of buffering, responsiveness,
etc. on current hardware and software designs.
(both need timestamps on to work well, besides)
TCP cubic is better maintained and understood than westwood,
also.
While a scenario where westwood would win possibly exists,
there is too much buffering in the wifi stack in particular
at present, to see any improvement.
If you wish to exercise various TCPs under contention,
the current svn head of netperf (2.6) has options to switch
congestion control agorithms on the fly, as does iperf.
SVN-Revision: 32514
2012-06-27 22:32:47 +00:00
1d7878a38b
fix SPI clock frequency selection
...
SVN-Revision: 32512
2012-06-27 22:14:50 +00:00
41909c6568
kernel: add missing config symbol
...
SVN-Revision: 32498
2012-06-24 20:21:27 +00:00
eee358338c
ramips: mac address detection for Fonera 2.0n
...
Detect and apply MAC address of a Fonera 2.0n (ramips)
Signed-off-by: Malte Forkel <malte.forkel@berlin.de>
Signed-off-by: Vasilis Tsiligiannis <b_tsiligiannis@silverton.gr>
SVN-Revision: 32490
2012-06-23 13:58:29 +00:00
81e8757da4
provide an early ioremap cookie of the system configuration register
...
SVN-Revision: 32489
2012-06-23 11:03:50 +00:00
98b2bc9189
group SYSDBG register defines in mcs814x.h
...
SVN-Revision: 32488
2012-06-23 11:03:45 +00:00
a8965f0005
make hardware.h a forward inclusion of mcs814x.h
...
mach/hardware.h is soon to be removed by upstream kernel
SVN-Revision: 32487
2012-06-23 11:03:40 +00:00
7c984552ed
remove platform specific initialization from ethernet driver
...
Hardware filtering must always be enabled as long as there is an Ethernet
device registered, and use device tree for setting the link activity and
buffer shifting enable/disable bit.
SVN-Revision: 32486
2012-06-23 11:03:35 +00:00
2c47bbc199
regroup interrupt controller register definitions in hardware.h
...
SVN-Revision: 32485
2012-06-23 11:03:29 +00:00
481c9faf20
remove handle_irq callback in board-mcs8140-dt.c
...
This should have been removed in r32470.
SVN-Revision: 32481
2012-06-21 12:20:47 +00:00
4b33e0996e
fix USB led triggers
...
SVN-Revision: 32474
2012-06-20 21:58:00 +00:00
a98c74164e
use generic uci defaults functions
...
SVN-Revision: 32473
2012-06-20 21:57:56 +00:00
007fa4d638
remove uselss cache invalidations
...
SVN-Revision: 32472
2012-06-20 21:57:53 +00:00
9a2367aa6d
improve ethernet driver debugging
...
SVN-Revision: 32471
2012-06-20 21:57:49 +00:00
3b0dba382b
do not use MULTI_IRQ_HANDLER it is bogus on our platform
...
This caused stalls in the Ethernet DMA block, so until properly
written and sorted out, fallback to the assembly version instead.
SVN-Revision: 32470
2012-06-20 21:57:45 +00:00
f45cd30543
verified to work - remove broken flag
...
SVN-Revision: 32469
2012-06-20 19:04:35 +00:00
1978c07539
Fix sysupgrade for squashfs, jffs2 and ext4 images
...
* use 'fsync' with 'dd' for image writing
* save config to boot partition
SVN-Revision: 32465
2012-06-19 22:36:53 +00:00
f4afa00862
add Moschip MSC814x support
...
This target currently only supports Moschip's MCS8140 SoC, but support
for other chips in the same family (MCS8142, MCS8144) will be easy to add.
Target support is entirely using Device Tree for probing peripherals.
Drivers support include:
- PCI
- USB 1 & 2
- watchdog
- random number generator
- UART
- timer
- internal Ethernet PHY
- Ethernet MAC core
Support for the following boards is included using Device Tree
- Devolo dLAN USB Extender
- Tigal RBT-832
SVN-Revision: 32462
2012-06-19 14:48:56 +00:00
7c87391c55
ar71xx: create profile and build image for the TL-WDR4300 board
...
SVN-Revision: 32461
2012-06-19 11:51:20 +00:00
2d97a52045
ar71xx: add user space support for the TL-WDR4300
...
SVN-Revision: 32460
2012-06-19 11:51:18 +00:00
8b9931fd27
ar71xx: add support for the TL-WDR4300 board
...
SVN-Revision: 32459
2012-06-19 11:51:17 +00:00
e6a10d5cdd
ar71xx: refresh patches
...
SVN-Revision: 32458
2012-06-19 11:51:15 +00:00
86c6543259
ar71xx: make AR8327 LEDs working on the DB120 board
...
SVN-Revision: 32457
2012-06-19 10:44:17 +00:00
b934fa2f16
generic: ar8216: allow to configure AR8327 LEDs via platform data
...
SVN-Revision: 32456
2012-06-19 10:44:16 +00:00
f509a87f2d
ar71xx: remove superfluous include of asm/mach-ath79/pci.h
...
SVN-Revision: 32455
2012-06-19 10:13:43 +00:00
1a1121158f
ar71xx: add a common function to configure USB power GPIOs
...
SVN-Revision: 32454
2012-06-19 10:13:41 +00:00
27fea0b6d7
ar71xx: correctly detect NETGEAR WNDRMAC
...
This patch helps properly detect a WNDRMAC device. Before this
patch the model is detected as "NETGEAR ?????????N".
Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
SVN-Revision: 32453
2012-06-19 10:13:38 +00:00
ee9bc123fb
ar71xx: add USB LED support by default for WNDR3700/WNDR3800/WNDRMAC
...
This adds kmod-leds-wndr3700-usb package to a default build for
WNDR3700, WNDR3800 and WNDRMAC in order to support the green USB LED.
Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
SVN-Revision: 32452
2012-06-19 10:13:37 +00:00
833b4af816
ramips: rt305x: add support for the Petatel PSR-680W Wireless CDMA Router
...
This patch adds support for the Korean made Petatel PSR-680W Wireless CDMA Router.
The platform is based on Ralink RT3052.
http://wiki.openwrt.org/toh/petatel/psr-680w
Signed-off-by: Dmitry Shmygov <shmygov at rambler.ru>
SVN-Revision: 32450
2012-06-19 09:52:15 +00:00
26cf21df02
ar71xx: add support for the embeddedwireless Dorin board (based on patch by embeddedwireless.de)
...
SVN-Revision: 32447
2012-06-19 00:22:04 +00:00
5d364d0ca1
ar71xx: add support for reading the MAC address from OTP ROM on AR933x
...
SVN-Revision: 32446
2012-06-19 00:21:58 +00:00
f06473f8ff
optimize kernel config for kvm_guest
...
This patch enables few extra kernel options for the kvm_guest subtarget:
- Tickless kernel to avoid timer ticks in idle guests, reduces CPU usage
- Enable paravirtualization steal time support
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 32436
2012-06-18 23:36:50 +00:00
cbac321164
remove inittab override
...
SVN-Revision: 32422
2012-06-18 11:50:37 +00:00
b89c81929e
fix SPI message control handling for BCM6338/6348
...
BCM6338 and BCM6338 have their MSG_CONTROL register width of 8-bits instead of
16-bits. We were previously using a 16-bits write which corrupted the first
byte of the TX FIFO. Also the message type was always set to Full-duplex even
in the case of half-duplex messages.
SVN-Revision: 32409
2012-06-17 16:17:29 +00:00
50958f5e03
kernel: replace the brcm47xx fuse workaround patches with a generic patch that applies to all mips targets
...
The dcache bug that it works around is a generic issue, not a brcm47xx cache quirk
SVN-Revision: 32395
2012-06-16 21:06:33 +00:00
b391548cf0
remove broken flags
...
Thanks to Nicolas Le Falher for testing on Bifferboard.
SVN-Revision: 32389
2012-06-16 16:45:28 +00:00
e3663ff907
use ttyS0 @ 115200 baud as default for KVM guests
...
SVN-Revision: 32384
2012-06-15 12:59:49 +00:00
1c80d9f21d
kirkwood: fix typo in uci-defaults/leds
...
Signed-off-by: Martin Mueller <mm@sig21.net>
SVN-Revision: 32343
2012-06-13 18:41:42 +00:00
dddf321b6e
ar71xx: swap the PHY address of the ethernet port of TL-MR3040/TL-MR11U similar to TL-MR3020 to fix ethernet link detection
...
SVN-Revision: 32336
2012-06-13 12:54:22 +00:00
f2271efc4e
bcm63xx: readd accidentially dropped ignore_oc in ehci driver
...
fixes overcurrent warning spam on 3.3 kernels for bcm63xx again.
SVN-Revision: 32221
2012-06-11 22:24:58 +00:00
be5229f0ba
kirkwood: ib62x0 fix reboot
...
SVN-Revision: 32131
2012-06-08 23:17:46 +00:00
43b5706ef5
xburst: remove an obsolete CompareKernelPatchVer call
...
SVN-Revision: 32115
2012-06-07 16:32:44 +00:00
6e5242952c
fix 553-board_96348w3.patch patch wrt gpio-keys-polled
...
SVN-Revision: 32096
2012-06-06 20:58:45 +00:00
624505df56
ar71xx: fix LZMA loader build regression from r32090 (thx, juhosg)
...
SVN-Revision: 32095
2012-06-06 19:37:49 +00:00
8b46a72583
kernel: add a few more tracing related symbols
...
SVN-Revision: 32094
2012-06-06 18:04:00 +00:00
73b8805e78
ar71xx: fix PHY setup on TL-MR3020 ( fixes #11572 )
...
SVN-Revision: 32093
2012-06-06 17:24:12 +00:00
dc9675282e
ar71xx: add a helper function for setting up PHY4 swapping on ar933x
...
SVN-Revision: 32092
2012-06-06 17:24:09 +00:00
02ab0d3ef9
ar71xx: only build all loader images if the image builder is enabled - saves some time on make target/install
...
SVN-Revision: 32090
2012-06-06 17:24:01 +00:00
4c25e42fa8
fix alarm led color for board 96348A-122
...
SVN-Revision: 32089
2012-06-06 16:07:46 +00:00
2f63f097de
add 96348w3 board ( #10764 )
...
SVN-Revision: 32088
2012-06-06 15:45:04 +00:00
9d38989d1f
update livebox board support ( #8677 )
...
Merge most fixes from #8677 :
- add basic hardware detection of Livebox Blue 5g revisions
- register leds and gpio buttons
- fix boot address location
- properly parse mac addresses
Plus some more fixes:
- make board_livebox.c more in line with board_bcm963xx.c
SVN-Revision: 32087
2012-06-06 15:44:56 +00:00
c69a2cdfbb
fix leds naming for all bcm63xx boards
...
SVN-Revision: 32086
2012-06-06 15:44:52 +00:00
ce1d4d7ee9
kernel: make tracing support configurable
...
SVN-Revision: 32085
2012-06-06 15:25:57 +00:00
23fc737b9d
backport upstream spi-bcm63xx fixes
...
* message pump conversion
* not using stopping state
* setting spi driver mode bits
SVN-Revision: 32078
2012-06-06 13:31:33 +00:00
7b12e9e49c
backport spi message queue infrastructure
...
SVN-Revision: 32077
2012-06-06 13:31:30 +00:00
4112094dbb
increase led number in patch 301-led_count.patch
...
So that board patches are only touching board-related code
SVN-Revision: 32076
2012-06-06 13:31:24 +00:00
95e69ac4f1
clean up generic image building
...
SVN-Revision: 32065
2012-06-05 17:49:42 +00:00
9a61b249c5
fix board patches so that new boards are withing appropriate ifdef
...
Some new board definitions were added within the #ifdef CONFIG_CPU_6338
section while some other were added within #ifdef CONFIG_CPU_6345, fix this
SVN-Revision: 32060
2012-06-05 13:40:41 +00:00
5ec2209734
refresh generic patches
...
SVN-Revision: 32059
2012-06-05 13:40:38 +00:00
36c99bcc42
fix bisectability of patch 303-spi-board-info.patch
...
It uses spi_register_board_info() from linux/spi/spi.h but does not include it
explicitely.
SVN-Revision: 32058
2012-06-05 13:40:35 +00:00
a4d96aae8d
bump to 3.3.8
...
SVN-Revision: 32055
2012-06-05 06:57:51 +00:00
605012ad5d
kirkwood: reorganize target
...
SVN-Revision: 32053
2012-06-05 00:43:56 +00:00
7f00e5ffc6
uboot-envtools: update to 2012.04.01
...
SVN-Revision: 32051
2012-06-04 21:55:49 +00:00
ffea8eb913
bcm63xx: fix ethernet on 96328avng and 963281TAN
...
The internal switch did not get registered.
SVN-Revision: 32041
2012-06-04 08:35:25 +00:00
2b4ef2eafa
adds unset Kbuild symbol
...
SVN-Revision: 32026
2012-06-02 14:03:32 +00:00
f4b02b91ce
malta: remove 3.2 patches
...
SVN-Revision: 32023
2012-06-02 12:06:28 +00:00
c0c60f7bd3
malta: use common kernel config
...
SVN-Revision: 32022
2012-06-02 12:06:26 +00:00
9375e83586
xburst: add missing config symbol
...
SVN-Revision: 32021
2012-06-02 12:06:15 +00:00
47ef62d1b8
adds patch to make Tantos (psb6970) switch buildable again
...
SVN-Revision: 32006
2012-05-30 17:41:28 +00:00
3fc76fb781
bcm63xx: build images for 6328 reference boards with various flash sizes
...
Build images for 96328avng and 963281TAN (untested) for three different
flash sizes: 4MB, 8MB, and 16MB.
Known issues:
* Button setup unknown, thus no fail-safe available.
* All other BCM6328 and BCM63XX issues
SVN-Revision: 32004
2012-05-30 10:27:46 +00:00
c454ba3657
bcm63xx: readd accidentially dropped network config for SPW303V
...
SVN-Revision: 32003
2012-05-30 10:27:42 +00:00
9e02593b70
generic: ar8216: add revision specific PHY fixups for AR8327
...
SVN-Revision: 32000
2012-05-29 16:39:27 +00:00
0d241e6670
generic: ar8216: replace chip_type field with chip_{ver,rev} in ar8216_priv
...
SVN-Revision: 31999
2012-05-29 16:39:26 +00:00
b2fce19a70
generic: ar8216: add chip_is_ar8{216,236,316,327} helpers
...
SVN-Revision: 31998
2012-05-29 16:39:24 +00:00
cd7ab1d30b
ar71xx: add default LED setup for the DB120 board
...
SVN-Revision: 31997
2012-05-29 16:39:23 +00:00
29a579e43a
cns21xx: use the generic uci-default functions for initial LED setup
...
SVN-Revision: 31996
2012-05-29 16:39:22 +00:00
ff74305623
lantiq: use the generic uci-default functions for initial LED setup
...
SVN-Revision: 31995
2012-05-29 16:39:21 +00:00
c81c6516de
kirkwood: use the generic uci-default functions for initial LED setup
...
SVN-Revision: 31994
2012-05-29 16:39:20 +00:00
ffbb4f88a9
ramips: use the generic uci-default functions for initial LED setup
...
SVN-Revision: 31993
2012-05-29 16:39:18 +00:00
4e40bdc190
ar71xx: use the generic uci-default functions for initial LED setup
...
SVN-Revision: 31992
2012-05-29 16:39:17 +00:00
ba3ad24514
kirkwood: use uci-defaults to configure different boards
...
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31990
2012-05-29 16:39:15 +00:00
c71838faa1
ramips: WAN LED for D-Link DIR-300-B1
...
Add led devices for D-Link DIR-300-B1 WAN LED.
Note that the GPIO state is also ANDed with the esw switch port 4
LED state, which is why I've set the amber LED to default-on.
Closes: https://dev.openwrt.org/ticket/11326
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
[ juhosg:
- fix comment style in mach-dir-300-revb.c,
- remove the PPP specific LED setup, not everyone uses a PPP connection
on the WAN interface]
SVN-Revision: 31989
2012-05-29 16:39:03 +00:00
a9cd8446f3
ar71xx: do not override the mdio clock for ar9330. the override value (obtained from an atheros driver) seems to break ethernet functionality
...
SVN-Revision: 31956
2012-05-28 20:39:50 +00:00
367e4b3994
ar71xx: improve rx performance of the ethernet driver by using build_skb to deliver a cache-hot skb to the network stack
...
SVN-Revision: 31934
2012-05-28 02:55:59 +00:00
8039a1bbb2
ar71xx: fix MII clock settings for various chips, improves ethernet stability on AR934x
...
SVN-Revision: 31925
2012-05-27 21:02:41 +00:00
f638414fdc
kernel: fix suppressing -s for linking modules when profiling is enabled
...
SVN-Revision: 31924
2012-05-27 21:02:36 +00:00
8865f0923e
ar71xx: fix TL-WR1041 image size
...
SVN-Revision: 31923
2012-05-27 17:21:47 +00:00
1c552ba8e5
ramips: rt3883: add device registration code for the SPI controller
...
SVN-Revision: 31922
2012-05-27 17:10:00 +00:00
9c241983fc
ramips: allow to use the SPI driver on RT3662/RT3883
...
SVN-Revision: 31921
2012-05-27 17:09:58 +00:00
78a750dcce
ramips: rt3883: fix GPIO reservation for the SPI pins
...
SVN-Revision: 31920
2012-05-27 17:09:56 +00:00
0622fdd82c
ramips: rt305x: remove superfluous controller_data assignment
...
SVN-Revision: 31919
2012-05-27 17:09:52 +00:00
7f5bec0642
ramips: make rt2x00 firmware extraction quiet
...
SVN-Revision: 31918
2012-05-27 17:09:50 +00:00
86dad96fd0
generic: rtl8367: rename a misnamed variable
...
SVN-Revision: 31917
2012-05-27 17:09:47 +00:00
705d31203c
generic: rtl8366_smi: remove duplicated spinlock initialization
...
SVN-Revision: 31916
2012-05-27 17:09:45 +00:00
9217115687
generic: rtl8366_smi: rename debugfs Kconfig symbol
...
SVN-Revision: 31915
2012-05-27 17:09:43 +00:00
466ef30173
generic: rtl8367: allow to use VLANs > 31
...
SVN-Revision: 31914
2012-05-27 17:09:41 +00:00
f567980d38
move files-3.3 -> files
...
SVN-Revision: 31912
2012-05-27 16:13:02 +00:00
8002770520
3.2 R.I.P.
...
SVN-Revision: 31911
2012-05-27 16:12:59 +00:00
81ddc886e1
dgn3500 support with eeprom loading from sysfs
...
WIFI eeprom:
As discussed, it is impossible for nand and spi flash platforms to have the eeprom data available from mtd. I suggested to load the eeprom from user-space. I've looked into regular firmware loading but this is only possible when using modules. I've created a sysfs entry that allows reading and writing the eeprom data to the platform data. After loading the eeprom data I rely on pci-hotplug support to disable the bogus pci device and rescan the bus (with fixups and all). Because hotplug is not available, an init script is created that performs the copy from mtd to platform data. I think it is best to eventually move the sysfs functions to dev_wifi_athxk.c file, this would get rid of the external to the ath9k platform data.
SPI flash:
It seems that the spi-xway driver is not really working. It causes my kernel to crash in all sorts of ways. I added to bitbang SPI to be able to the calibration data mention above.
I've kept the original mtd partitioning that Netgear uses.
Buttons/LED:
Both buttons are working properly. Two leds are not enabled: The red internet led is connected to the pci_gnt1 pin... I can't disable it because then DMA stops working.
The green wifi led is connected to an unknown atheros gpio.
Signed-off-by: Pieter Voorthuijsen <p.voorthuijsen at gmail.com>
SVN-Revision: 31910
2012-05-27 16:02:22 +00:00
6e8fe84472
fixes zyxel p2601hnfx
...
moves the linux partition, removes the config partition and the
buttons settings have small adjustments.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31909
2012-05-27 16:02:20 +00:00
3f2f50c681
Add basic configuration for new board ZTE H201L. Still missing are button and led gpio values.
...
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31908
2012-05-27 16:02:16 +00:00
51bc47ce7c
kernel: properly pad the allocated headroom in skb_cow to NET_SKB_PAD
...
SVN-Revision: 31906
2012-05-27 15:16:37 +00:00
0b8c1c8dfb
linux/3.2: R.I.P.
...
SVN-Revision: 31905
2012-05-27 15:01:37 +00:00
20ba6d90e3
xburst: remove support for old kernels
...
SVN-Revision: 31904
2012-05-27 15:01:35 +00:00
d043cb2c34
xburst: switch to 3.3 and add broken flag
...
SVN-Revision: 31903
2012-05-27 15:01:33 +00:00
9a26e9f843
xburst: add support for 3.3
...
SVN-Revision: 31902
2012-05-27 15:01:32 +00:00
9dd7a6d9e2
ppc44x: remove 3.2 support
...
SVN-Revision: 31901
2012-05-27 15:01:30 +00:00
05d74942b1
ppx44x: switch to 3.3 and add broken flag
...
SVN-Revision: 31900
2012-05-27 15:01:28 +00:00
9300e0496c
ppc44x: add support for 3.3
...
Compile tested only.
SVN-Revision: 31899
2012-05-27 15:01:27 +00:00
c50f1f7536
cobalt: switch to 3.3 and add broken flag
...
Compile tested only.
SVN-Revision: 31898
2012-05-27 15:01:26 +00:00
471cf87ff0
ep93xx: remove 3.2 support
...
SVN-Revision: 31897
2012-05-27 15:01:24 +00:00
400b9b5b87
ep93xx: switch to 3.3 and add broken flag
...
SVN-Revision: 31896
2012-05-27 15:01:23 +00:00
7501f2364f
ep93xx: add support for 3.3
...
Compile tested only.
SVN-Revision: 31895
2012-05-27 15:01:21 +00:00
907e88a37f
au1000: remove 3.2 support
...
SVN-Revision: 31894
2012-05-27 15:01:18 +00:00
fbe10e73c6
au1000: switch to 3.3 and add broken flag
...
SVN-Revision: 31893
2012-05-27 15:01:17 +00:00
e065d5cfbe
au1000: add support for 3.3
...
Compile tested only.
SVN-Revision: 31892
2012-05-27 15:01:15 +00:00
de4c4d35e1
linux/3.1: R.I.P.
...
SVN-Revision: 31891
2012-05-27 15:01:09 +00:00
cead4b47ab
omap24xx: remove 3.1 support
...
SVN-Revision: 31890
2012-05-27 15:01:07 +00:00
7a4db11fbb
omap24xx: switch to 3.3 and add broken flag
...
SVN-Revision: 31889
2012-05-27 15:01:05 +00:00
d004168445
cns3xxx: remove 3.1 support
...
SVN-Revision: 31888
2012-05-27 15:01:03 +00:00
6f2ca5da39
cns3xxx: switch to 3.3 and add broken flag
...
SVN-Revision: 31887
2012-05-27 15:01:02 +00:00
6f89cffc9a
kernel: add a few patches for avoiding unnecessary skb reallocations - significantly improves ethernet<->wireless performance with mac80211 based drivers
...
SVN-Revision: 31886
2012-05-27 14:43:58 +00:00
ec7786c2ec
bcm63xx: build images for DSL-274XB revision F1
...
Build images for D-Link DSL-274XB revision F1. Flashing
through original web UI as well as CFE works.
Known issues:
* wifi led inverted (on when wifi is off and vice cersa)
* same issues as generic bcm6328 support
SVN-Revision: 31885
2012-05-27 13:22:51 +00:00
8aac009cc9
bcm63xx: add ath9k to atheros wifi profile
...
SVN-Revision: 31884
2012-05-27 13:22:48 +00:00
4aa43122ab
bcm63xx: enable bcm6328 support and required drivers
...
BCM6328 support is in a usable state, with the following issues
* internal switch port not configurable
* external phys not supported
* broadcom wifis will probably not work correctly
* and all other generic bcm63xx issues (so yes, still no ADSL)
SVN-Revision: 31883
2012-05-27 13:22:46 +00:00
e5575fe335
bcm63xx: add support for DSL-274XB rev F1
...
SVN-Revision: 31882
2012-05-27 13:22:43 +00:00
a7a82db16f
bcm63xx: fix port state after network down
...
bcm_enetsw_probe did not properly reset port states, resulting in
connected ports staying disabled after bringing up the interface the
second time.
SVN-Revision: 31881
2012-05-27 13:22:40 +00:00
e19ed52fd1
bcm63xx: add a fixup for ath9k devices
...
SVN-Revision: 31880
2012-05-27 13:22:37 +00:00
e34018cc9e
bcm63xx: add support for the HSSPI controller
...
Add support for the HSSPI controller found on bcm6328 and SPI attached
flash.
SVN-Revision: 31879
2012-05-27 13:22:33 +00:00
099d5eec06
bcm63xx: add preliminary support for bcm6328
...
SVN-Revision: 31878
2012-05-27 13:22:29 +00:00
7dbb132c88
bcm63xx: add flash type detection
...
SVN-Revision: 31877
2012-05-27 13:22:25 +00:00
b0ffeb0021
bcm63xx: pad Speedport W303 V images to 4 MiB
...
Prevents CFE from flashing to the second image offset. Fix up the rootfs
length on first boot else CFE will complain.
SVN-Revision: 31876
2012-05-27 13:22:22 +00:00
226b030e44
bcm63xx: add a default switch configuration for DSL-274XB
...
SVN-Revision: 31874
2012-05-27 13:22:17 +00:00
db1ff5c6fa
bcm63xx: setup network config through uci-defaults
...
SVN-Revision: 31873
2012-05-27 13:22:14 +00:00
72b4fdecc9
bcm63xx: move the board name workaround to /lib/brcm63xx.sh
...
SVN-Revision: 31872
2012-05-27 13:22:11 +00:00
dd37687de0
bcm63xx: use the exact board id as board identification string
...
No need to keep the bcm63xx/ at the start or the chipid info at the end.
SVN-Revision: 31871
2012-05-27 13:22:08 +00:00
230c0eb2cb
kernel: fix a warning in the connmark module
...
SVN-Revision: 31856
2012-05-24 18:25:08 +00:00
2ae5581447
kernel: update linux 3.3 to 3.3.7
...
SVN-Revision: 31848
2012-05-23 21:05:32 +00:00
c57409e79d
ar71xx: fix an insignificant typo
...
Patch from #11485 .
SVN-Revision: 31847
2012-05-23 21:05:30 +00:00
013f434f5b
ar71xx: fix WLAN led for RB751U-2HnD and RB751G-2HnD
...
Patch by Kamil Trzciński <ayufan@osk-net.pl>
SVN-Revision: 31846
2012-05-23 21:05:25 +00:00
758f670376
ar71xx: add support for TP-Link TL-MR3040
...
Support for TP-Link TL-MR3040. Power LED not working - always on red, after
start should be green.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 31845
2012-05-23 21:05:24 +00:00
e4720dfa95
ramips: Add byte queue limits support to net/ethernet/ramips_main.c
...
Add byte queue limits support to net/ethernet/ramips_main.c
"Byte queue limits are a mechanism to limit the size of the transmit
hardware queue on a NIC by number of bytes. The goal of these byte
limits is too reduce latency (HOL blocking) caused by excessive
queuing in hardware (aka buffer bloat) without sacrificing
throughput."
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 31844
2012-05-23 21:05:23 +00:00
1d286fd755
ramips: Enable sysupgrade for Sitecom WL-351
...
Sysupgrade works just fine on my Sitecom WL-351 after adding this
oneliner.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 31843
2012-05-23 21:05:22 +00:00
1e1c0a5405
linux/3.3: avoid recursive calling of mtd_writev in the block2mtd driver
...
Should fix #11513 . Tested with the x86/generic squashfs image within a VM.
SVN-Revision: 31841
2012-05-23 21:05:19 +00:00
9037c2ccc6
lantiq: allow platforms with rt2x00 to override the mac address without overriding eeprom, fixes bogus wlan mac address on arv4520
...
SVN-Revision: 31835
2012-05-20 21:58:03 +00:00
ce59af117c
kernel: merge a net-next fq_codel backlog handling fix
...
SVN-Revision: 31813
2012-05-18 22:12:15 +00:00
02c2f449d7
omap24xx: add support for 3.3
...
Compile tested only.
SVN-Revision: 31810
2012-05-18 20:22:32 +00:00
c2a2d59db5
cns3xxx: add support for 3.3
...
Compile tested only.
SVN-Revision: 31809
2012-05-18 20:10:53 +00:00
1fd4bf270b
linux/2.6.39: R.I.P.
...
SVN-Revision: 31808
2012-05-18 20:10:51 +00:00
05c0d8b28e
cns3xxx: sync kernel config
...
SVN-Revision: 31807
2012-05-18 20:10:48 +00:00
9718f03e24
cns3xxx: remove 2.6.39 support
...
SVN-Revision: 31806
2012-05-18 20:10:46 +00:00
9e78becbac
cns3xxx: switch to 3.1
...
Compile tested only.
SVN-Revision: 31805
2012-05-18 20:10:44 +00:00
07b5a3eea2
x86: remove support for old kernels
...
SVN-Revision: 31804
2012-05-18 20:10:42 +00:00
604e3aac0a
x86: remove subtarget specific LINUX_VERSION overrides
...
SVN-Revision: 31803
2012-05-18 20:10:38 +00:00
d9dab97d38
x86/ep80579: switch to 3.3
...
Also fix build errors in the ep80579-drivers package.
Compile tested only.
SVN-Revision: 31802
2012-05-18 20:10:33 +00:00
c63ef04874
brcm47xx: fix nvram read out on devices with serial flash
...
detect nvram on Linksys E3200
SVN-Revision: 31790
2012-05-18 16:04:10 +00:00
7ad663dda6
brcm47xx: bcma: fix null pointer
...
SVN-Revision: 31789
2012-05-18 15:46:30 +00:00
b4ecf522cd
brcm47xx: ssb: recognize ARM Cortex M3
...
SVN-Revision: 31788
2012-05-18 15:45:51 +00:00
7be88d2ad8
brcm47xx: some fixes for the USB driver
...
SVN-Revision: 31787
2012-05-18 15:44:25 +00:00
e3678eb33e
cobalt: remove 2.6.39 specific patches
...
SVN-Revision: 31785
2012-05-18 09:59:22 +00:00
a5de52c244
x86/olpc: switch to 3.3
...
Compile tested only.
SVN-Revision: 31784
2012-05-18 09:57:32 +00:00
9e54e012d6
x86: image: select bootscript images by default for OLPC
...
SVN-Revision: 31783
2012-05-18 09:57:29 +00:00
3f62f5211a
adm5120: add missing config symbols for the rb1xx subtarget, fixes #11407
...
SVN-Revision: 31781
2012-05-17 21:20:23 +00:00
c30405070c
kernel: add some missing config options added by r31756
...
SVN-Revision: 31774
2012-05-17 13:28:30 +00:00
273797f15a
kernel: ssb/bcma: update to version from wireless-testing tag master-2012-05-16-2
...
SVN-Revision: 31772
2012-05-17 13:22:38 +00:00
3491d8c017
brcm47xx: remove support for kernel 3.2
...
SVN-Revision: 31771
2012-05-17 13:20:10 +00:00
562e468ae5
x86/thincan: switch to 3.3
...
Compile tested only.
SVN-Revision: 31765
2012-05-17 06:41:01 +00:00
1f7f8376a6
x86/xen_domu: switch to 3.3
...
Compile tested only.
SVN-Revision: 31764
2012-05-17 06:41:00 +00:00
8bb7ddecfd
x86/kvm_guest: switch to 3.3
...
Compile tested only.
SVN-Revision: 31763
2012-05-17 06:40:58 +00:00
f14d1a588d
x86/generic: switch to 3.3
...
Compile tested only.
SVN-Revision: 31762
2012-05-17 06:40:56 +00:00
54edbfabac
kernel: add codel and fq_codel to generic 3.3 patch set (based on patch by Dave Täht)
...
Codel is a new AQM algorithm and RED replacement designed by
Kathie Nichols and Van Jacobson, and published in ACM queue:
http://queue.acm.org/detail.cfm?id=2209336
Codel stands for "Controlled Delay", and needs no knobs in the
general case, twiddled, for optimum results. It aims for 5ms of
delay, at most, when in use.
Additionally,
fq_codel (by eric dumazet) builds on codel to provide fair queuing
superior to what could be had with SFQ, and drop behavior saner
than RED, BLUE, or choke.
These patches are backported from net-next and are known to work
on Linux 3.3.4 and later.
Includes updates to codel for better portability and speed
SVN-Revision: 31756
2012-05-16 15:23:03 +00:00
eb2fe5e863
x86/alix2: switch to 3.3
...
Compile tested only.
SVN-Revision: 31753
2012-05-16 10:45:02 +00:00
fb7da5bbde
x86/net5501: switch to 3.3
...
Compile tested only.
SVN-Revision: 31752
2012-05-16 10:44:59 +00:00
9e049ce25c
x86: sync 3.3 configs
...
SVN-Revision: 31751
2012-05-16 10:44:55 +00:00
19f691f8e4
x86: sync 3.2 configs
...
SVN-Revision: 31750
2012-05-16 10:44:52 +00:00
724fd5e657
x86: sync 2.6.39 configs
...
SVN-Revision: 31749
2012-05-16 10:44:49 +00:00
637fd23428
linux/3.3: add missing symbol
...
SVN-Revision: 31748
2012-05-16 10:44:46 +00:00
67675fd48d
linux: add CONFIG_POWER_SUPPLY_DEBUG symbol
...
It was missing in the previous commit.
SVN-Revision: 31738
2012-05-15 11:12:31 +00:00
39994008cb
linux: move certain disabled symbols to the generic configs
...
* CONFIG_ARCH_DMA_ADDR_T_64BIT
* CONFIG_ARCH_HAS_ILOG2_U32
* CONFIG_ARCH_HAS_ILOG2_U64
* CONFIG_ARCH_PHYS_ADDR_T_64BIT
* CONFIG_ARCH_SUPPORTS_MSI
* CONFIG_GENERIC_CPU_DEVICES
* CONFIG_HWMON_DEBUG_CHIP
* CONFIG_I2C_PXA_PCI
* CONFIG_LEDS_GPIO
* CONFIG_MINIX_FS_NATIVE_ENDIAN
* CONFIG_MLX4_CORE
* CONFIG_POWER_SUPPLY
* CONFIG_POWER_SUPPLY_DEBUG
* CONFIG_QUOTACTL
* CONFIG_SDIO_UART
* CONFIG_SENSORS_K10TEMP
* CONFIG_SENSORS_SCH56XX_COMMON
* CONFIG_SENSORS_VIA_CPUTEMP
* CONFIG_SERIO_AMBAKMI
* CONFIG_SERIO_I8042
* CONFIG_SERIO_LIBPS2
* CONFIG_SERIO_PCIPS2
* CONFIG_SERIO_RAW
* CONFIG_SERIO_SERPORT
* CONFIG_SPI_BITBANG
* CONFIG_SPI_GPIO
SVN-Revision: 31737
2012-05-15 10:58:52 +00:00
a3f2fd187b
ar71xx: remove AG71XX_RX_PKT_RESERVE, it is no longer necessary (found by Eric Dumazet)
...
SVN-Revision: 31736
2012-05-15 10:36:39 +00:00
364f47e454
code style cleanup of the mach files
...
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31735
2012-05-15 09:38:05 +00:00
07dca108a9
adds zyxel p2601hnfx support
...
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31734
2012-05-15 09:38:02 +00:00
9785ec070e
set 3.3.6 as default
...
SVN-Revision: 31733
2012-05-15 09:37:59 +00:00
c61ada1db8
set 3.3.5 as default
...
SVN-Revision: 31718
2012-05-14 16:11:26 +00:00
2fceae7ec4
linux/3.0: R.I.P.
...
It is used by the broken omap35xx/gumstix target only.
SVN-Revision: 31717
2012-05-14 15:48:34 +00:00
a3d349a3b3
realview: remove 3.0 support
...
SVN-Revision: 31716
2012-05-14 15:48:32 +00:00
e2ecabd761
realview: switch to 3.3
...
SVN-Revision: 31715
2012-05-14 15:48:31 +00:00
46c7d58726
realview: add 3.3 support
...
SVN-Revision: 31714
2012-05-14 15:48:29 +00:00
8f629f2a22
linux/3.3: more missing config symbols
...
SVN-Revision: 31713
2012-05-14 15:48:23 +00:00
a798a81890
kernel: add CONFIG_BLK_DEV_PCIESSD_MTIP32XX
...
SVN-Revision: 31710
2012-05-14 11:28:02 +00:00
b472e5d12e
kernel: update linux 3.3 to 3.3.6
...
SVN-Revision: 31709
2012-05-14 09:18:32 +00:00
679b6a0722
amazon: fix section mismatch
...
SVN-Revision: 31707
2012-05-13 15:31:42 +00:00
abd74f86b4
amazon: update amazon target to kernel 3.3
...
This is just compile tested, my device is currently not working.
SVN-Revision: 31706
2012-05-13 15:10:40 +00:00
60d3ffb49a
gemini: remove 2.6.37 support
...
SVN-Revision: 31700
2012-05-13 12:04:04 +00:00
672ff3de6e
gemini: switch to 3.3
...
SVN-Revision: 31699
2012-05-13 12:04:02 +00:00
d0ac4c1f03
gemini: add support for 3.3
...
SVN-Revision: 31698
2012-05-13 12:03:59 +00:00
482b99a660
brcm47xx: generate image for Linksys WRT610N V1
...
SVN-Revision: 31696
2012-05-13 00:16:57 +00:00
31c2c485c1
kernel: ssb: add PCI IDs 0x4322 and 43222
...
The 0x4322 ID is found on the BCM4322 used on some SoCs like the
Linksys WRT610N V1 connected to a BCM4705. The 43222 (0xa8d6) ID
is found on the BCM43222 used on some other SoCs like the D-Link
DSL-2760U connected to a BCM63xx.
This fixes #10887 .
SVN-Revision: 31695
2012-05-13 00:08:12 +00:00
5acb0b72be
brcm47xx: fix tg3 ssb patch
...
Now tg3 works with the Ethernet core of the Linksys WRT610N v1 (again).
SVN-Revision: 31694
2012-05-12 23:59:12 +00:00
e710aeeab1
linux/2.6.38: R.I.P.
...
It is used only by the broken coldfire target.
SVN-Revision: 31688
2012-05-12 12:05:21 +00:00
08ed044595
linux/2.6.37: R.I.P.
...
SVN-Revision: 31687
2012-05-12 12:05:19 +00:00
c8cede6aa7
linux: add broken flag to remaining targets which are using 2.6.37
...
SVN-Revision: 31686
2012-05-12 12:05:18 +00:00
a2efef024e
iop32x: remove 2.6.37 support
...
SVN-Revision: 31685
2012-05-12 10:49:36 +00:00
a5d4de7da2
iop32x: switch to 3.3
...
It is compile tested only, so add a broken flag.
SVN-Revision: 31684
2012-05-12 10:49:34 +00:00
598fe0e93b
iop32x: add 3.3 support
...
SVN-Revision: 31683
2012-05-12 10:49:32 +00:00
bf8e96712e
sibyte: remove 2.6.37 support
...
SVN-Revision: 31682
2012-05-12 10:49:30 +00:00
edb129bb24
sibyte: switch to 3.3
...
It is compile tested only, so add a broken flag.
SVN-Revision: 31681
2012-05-12 10:49:28 +00:00
fd651daa4b
sibyte: add 3.3 support
...
SVN-Revision: 31680
2012-05-12 10:49:26 +00:00
4f6acae5f7
ixp4xx: fix ixp4xx_crypto build error
...
SVN-Revision: 31679
2012-05-12 10:49:23 +00:00
cabfa5b364
orion: remove the broken broken flag
...
It is working on the Linksys WRT350N v2 at least:
http://pastebin.com/KCAbJZs9
Additionally, the flag was added to a wrong place
so it had no effect.
Thanks to StrikerNL for testing.
SVN-Revision: 31674
2012-05-10 20:20:43 +00:00
ec27c35ebe
kirkwood: fix Kconfig symbol for NSA-310
...
SVN-Revision: 31673
2012-05-09 16:16:52 +00:00
dc4cfd3a64
Add 3.3 config files
...
SVN-Revision: 31672
2012-05-09 12:52:24 +00:00
75827c538d
Add missing 3.3 patches
...
SVN-Revision: 31671
2012-05-09 12:52:21 +00:00
7d638fbb2f
Drop 2.6.32 support
...
SVN-Revision: 31670
2012-05-09 12:52:19 +00:00
200227e0b4
kirkwood: add support for the ZyXEL NSA-310
...
SVN-Revision: 31669
2012-05-09 11:38:43 +00:00
213cbf4297
kirkwood: add RaidSonic ICY BOX IB-NAS62x0 board support
...
Based on a patch by Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31668
2012-05-09 11:38:41 +00:00
d4876692c1
kirkwood: enable GPIO sysfs interface
...
SVN-Revision: 31667
2012-05-09 11:38:40 +00:00
d1eed108bb
kirkwood: nuke 2.6.37 support
...
SVN-Revision: 31666
2012-05-09 11:38:39 +00:00
861b9b25e0
kirkwood: switch to 3.3
...
SVN-Revision: 31665
2012-05-09 11:38:37 +00:00
b272041998
kirkwood: add 3.3 support
...
Based on the 3.2.9 patches by Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31664
2012-05-09 11:38:36 +00:00
500ec36515
ixp4xx: nuke 2.6.37 support
...
SVN-Revision: 31663
2012-05-09 10:48:44 +00:00
d25a4e7ddc
ixp4xx: switch to 3.3
...
SVN-Revision: 31662
2012-05-09 10:48:43 +00:00
d5093de0b1
mpc85xx: remove 2.6.38 support
...
SVN-Revision: 31661
2012-05-09 10:48:41 +00:00
ab71a428c5
mpc85xx: switch to 3.3 and add broken flag
...
It is compile tested only.
SVN-Revision: 31660
2012-05-09 10:48:39 +00:00
db376b45d9
orion: nuke 3.0 support
...
SVN-Revision: 31659
2012-05-09 10:48:38 +00:00
24e2385a59
orion: switch to 3.3 and add broken flag
...
It is compile tested only.
SVN-Revision: 31658
2012-05-09 10:48:37 +00:00
d640a15b73
linux/3.3: add missing RTC symbol
...
SVN-Revision: 31654
2012-05-09 10:48:30 +00:00
93c9980b94
ar71xx: fix build error if PCI is disabled
...
SVN-Revision: 31646
2012-05-07 21:16:22 +00:00
34018a630f
kernel: update linux 3.3 to 3.3.5
...
SVN-Revision: 31645
2012-05-07 20:11:43 +00:00
6b5012ce1f
pxa: remove 2.6.37 support
...
SVN-Revision: 31643
2012-05-07 17:40:15 +00:00
1f1fd8616f
pxa: switch to 3.3 and mark it as broken
...
It is working in qemu, but it has not been tested on real hardware.
SVN-Revision: 31642
2012-05-07 17:40:09 +00:00
b284c0e804
pxa: add support for 3.3
...
SVN-Revision: 31641
2012-05-07 17:40:06 +00:00
1a01559520
atheros: Fix compilation
...
With our recent switch to the 3.3 kernel target, some headers were
occidentally omitted.
Signed-off-by: Jonathan Bither <jonbither@gmail.com>
SVN-Revision: 31640
2012-05-07 17:06:39 +00:00
b218b15709
bcm63xx: fix a race between PCI bus scan and fallback sprom registration
...
The fallback sprom handler was installed too late, resulting in ssb
failing to get a valid sprom on some devices.
Fixes #11384 .
SVN-Revision: 31638
2012-05-06 21:25:34 +00:00
0ff3c396d3
kernel: rewrite the phy packet hook, put it in the network stack to avoid having to keep non-upstream ethernet driver changes
...
SVN-Revision: 31637
2012-05-06 21:19:14 +00:00
d30f8da466
brcm47xx: add gpio_request_one()
...
This fixes a compile error with kernel 3.3.
SVN-Revision: 31635
2012-05-06 20:44:37 +00:00
7799c88aa4
atheros: clean up the patches some more
...
SVN-Revision: 31626
2012-05-06 17:15:00 +00:00
9b20187ad5
atheros: update to 3.3.4 (based on work by acoul), fix mvswitch driver for newer kernels
...
SVN-Revision: 31625
2012-05-06 17:08:30 +00:00
30362b90af
AR7: don't mark as broken
...
Linux 3.3.4 boots fine on my AR7 device.
SVN-Revision: 31623
2012-05-06 14:04:19 +00:00
28e897845f
ar7: remove 2.6.37 support
...
SVN-Revision: 31617
2012-05-05 17:32:43 +00:00
047a51c4fd
ar7: switch to 3.3 and mark the target as broken
...
SVN-Revision: 31616
2012-05-05 17:32:41 +00:00
dd884a6b73
ar7: add 3.3 support
...
SVN-Revision: 31615
2012-05-05 17:32:39 +00:00
e85a44f11b
ar7: fix kernel_entry extraction
...
SVN-Revision: 31614
2012-05-05 17:32:36 +00:00
9486904079
ar71xx: add profile and build image for the TL-WR1041N v2 board
...
Patch-by: Vince Huang <axishero@foxmail.com>
SVN-Revision: 31610
2012-05-05 17:02:41 +00:00
ab897ab04e
ar71xx: add support for the TP-Link TL-WR1041N v2 board
...
Patch-by: Vince Huang <axishero@foxmail.com>
SVN-Revision: 31608
2012-05-05 17:02:35 +00:00
56f2e08537
ar71xx: update 3.3 patches
...
SVN-Revision: 31602
2012-05-05 13:56:35 +00:00
8fffc6d6df
ar71xx: fix a typo in the db120 mach file
...
Reported-by: Sven Eckelmann <sven@narfation.org>
SVN-Revision: 31601
2012-05-05 13:56:30 +00:00
8c352ff853
brcm47xx: update target to kernel 3.3
...
SVN-Revision: 31599
2012-05-05 12:53:37 +00:00
2e3f8c480e
linux/2.6.32: R.I.P.
...
SVN-Revision: 31597
2012-05-05 11:43:34 +00:00
e005aed223
rdc: remove 2.6.32 support
...
SVN-Revision: 31596
2012-05-05 11:43:32 +00:00
0e086cfaf7
rdc: switch to 3.3 and mark the target as broken
...
SVN-Revision: 31595
2012-05-05 11:43:30 +00:00
787b253859
rb532: remove 2.6.32 support
...
SVN-Revision: 31594
2012-05-05 11:43:29 +00:00
63a532a472
rb532: switch to 3.3 and mark the target broken
...
SVN-Revision: 31593
2012-05-05 11:43:26 +00:00
b120e7f22a
rb532: add 3.3 support
...
SVN-Revision: 31592
2012-05-05 11:43:23 +00:00
6caa1aab10
mpc83xx: remove broken flag
...
SVN-Revision: 31591
2012-05-05 11:43:21 +00:00
257a201b56
mpc83xx: populate network config from an uci-default script
...
SVN-Revision: 31590
2012-05-05 11:43:19 +00:00
13ce8f8a77
mpc83xx: cleanup rb333.dts
...
SVN-Revision: 31589
2012-05-05 11:43:16 +00:00
a3d9877518
mpc83xx: fix MAC addresses on the RB333
...
SVN-Revision: 31588
2012-05-05 11:43:13 +00:00
1a5a9c5dae
mpc83xx: fix build warnings in RB333/600 dtb wrappers
...
SVN-Revision: 31587
2012-05-05 11:43:10 +00:00
7ffa3fe02c
linux/2.6.32: fix layer7 patch
...
SVN-Revision: 31586
2012-05-05 07:20:13 +00:00
9a91dc9f71
upgrade to 3.3, enable framebuffer
...
SVN-Revision: 31576
2012-05-03 21:51:58 +00:00
b393464fb4
adm5120: add missing NULL terminator to partition parser list
...
Fixes #11372 .
SVN-Revision: 31574
2012-05-03 21:03:50 +00:00
22b2e3fbb9
brcm47xx: add support for kernel 3.3
...
SVN-Revision: 31573
2012-05-03 20:18:41 +00:00
3349cf2691
Fix iptables abuse of kernel header files. Use exported headers instead.
...
[juhosg: export xt_layer7.h for all kernel versions]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SVN-Revision: 31566
2012-05-03 09:43:10 +00:00
b0449ccf04
ramips: W306R V2.0 - GPIO and Network fixes
...
Fixed: GPIO typos and confirmed GPIO_BUTTON_RESET
Fixed: Lan & Wan reversed: swaped "eth0.2" with "eth0.1" by
removing a line(default is correct), and reversed the
Lan/wan layout LLLLW to WLLLL.
Added: image/Makefile now builds -factory.bin files. I am
unsure of the accepted way to change the makefile but
the name of the image needs to be 'linkn Kernel Image'
in order to be accepted by the OEM firmware.
Known issue: eth0 (internal switch i think has mac address:
00:11:22:33:44:55 but i think it should be same as
the lan).
Known issue: Pressing the reset button has no noticable effect,
i would expect the router to boot failsafe if being
pressed on boot, reboot if short press and reset all
to default if long press.
[juhosg: remove mtdlayout_W306R and use mtdlayout_4M instead]
Signed-off-by: David Pearce <david_18051985@hotmail.com>
SVN-Revision: 31557
2012-05-02 19:17:59 +00:00
90e99b9fe8
ramips: Make serial console for DIR-300-B1 work again
...
Make serial console for DIR-300-B1 work again.
With some recent change, "console=ttyS1,57600" was removed from the
default kernel command line, this adds the necessary mkcmdline
incantation to image/Makefile to add it there for this target.
This is quite likely broken for other targets as well.
Without this the console switches to ttyS0 instead of ttyS1 and
kernel output is missing, and the userspace comes up with 9600 baud
instead of 57600.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 31556
2012-05-02 19:17:58 +00:00
fb28062182
mpc83xx: remove 2.6.36 support
...
SVN-Revision: 31555
2012-05-02 18:27:26 +00:00
3269924fed
mpc83xx: switch to 3.3
...
SVN-Revision: 31554
2012-05-02 18:27:25 +00:00
8ee595315d
mpc83xx: add support for 3.3
...
SVN-Revision: 31553
2012-05-02 18:27:22 +00:00
b4b5f2d018
linux/3.3: add more missing symbols
...
SVN-Revision: 31552
2012-05-02 18:27:19 +00:00
5d9b44d110
use a define for the poll and debounce interval
...
SVN-Revision: 31550
2012-05-02 15:40:26 +00:00
7a2b3d8a55
linux/3.3: add more missing symbols
...
SVN-Revision: 31548
2012-05-01 08:00:26 +00:00
70322ba3d1
move CONFIG_BOOKE_WDT_DEFAULT_TIMEOUT to the target configs
...
SVN-Revision: 31547
2012-05-01 08:00:25 +00:00
880de62f91
switch to 2.6.38
...
SVN-Revision: 31546
2012-05-01 07:00:17 +00:00
cbfce53831
kernel: update linux 3.3 to 3.3.4
...
SVN-Revision: 31541
2012-04-30 08:38:11 +00:00
e931ffd678
linux: rtl836x: add a generic reset_switch function
...
SVN-Revision: 31536
2012-04-29 18:29:31 +00:00
1d9400263f
linux: rtl836x: rename rtl836*_hw_init to rtl836*_setup
...
SVN-Revision: 31535
2012-04-29 18:29:29 +00:00
badd7a3cf2
linux: rtl836x: add a reset_chip callback to rtl8366_smi_ops
...
SVN-Revision: 31534
2012-04-29 18:29:26 +00:00
3e3a4d3d6b
ar71xx: allow to disable link polling on unused PHYs
...
SVN-Revision: 31533
2012-04-29 18:29:24 +00:00
a8d3109208
rb532: remove 2.6.35 support
...
The generic 2.6.35 support has been remove long time ago.
SVN-Revision: 31532
2012-04-29 16:56:07 +00:00
532b74ff7b
linux/3.3: refresh patches
...
SVN-Revision: 31531
2012-04-29 16:56:03 +00:00
27a1f6652a
rdc: add 3.3 support
...
SVN-Revision: 31530
2012-04-29 15:59:49 +00:00
c59b60fa0b
mpc85xx: add support for 3.3
...
Based on a patch by Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
SVN-Revision: 31529
2012-04-29 15:55:28 +00:00
f687ca2296
orion: add 3.3 support
...
SVN-Revision: 31528
2012-04-29 15:20:40 +00:00
923ebbac81
linux/3.3: yet another missing symbol
...
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
SVN-Revision: 31527
2012-04-29 15:08:24 +00:00
55fdc18beb
linux/3.3: add support for the Pericom PT7C4338 I2C RTC chip
...
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
SVN-Revision: 31525
2012-04-29 15:08:22 +00:00
f6d5998d31
mpc85xx: add kmod-booke-wdt to the default packages
...
Based on a patch by Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
SVN-Revision: 31523
2012-04-29 15:00:38 +00:00
296086868a
mpc85xx: don't override CONFIG_WATHCDOG
...
SVN-Revision: 31521
2012-04-29 15:00:36 +00:00
77735b5930
linux: move CONFIG_BOOKE_WDT to the generic config
...
SVN-Revision: 31520
2012-04-29 15:00:34 +00:00
4fa9cf6c33
linux/2.6.36: R.I.P.
...
SVN-Revision: 31519
2012-04-29 15:00:33 +00:00
3bc2afc384
linux: add broken flag to targets which are using 2.6.36
...
SVN-Revision: 31518
2012-04-29 15:00:32 +00:00
417185b33c
adm5120: create a new subtarget for the RB1xx devices
...
SVN-Revision: 31513
2012-04-29 07:36:46 +00:00
7925eea45f
adm5120: share a common kernel config between the subtargets
...
SVN-Revision: 31512
2012-04-29 07:36:44 +00:00
e96d52d198
adm5120: merge 3.3 patches
...
SVN-Revision: 31511
2012-04-29 07:36:43 +00:00
19be4923e0
adm5120: remove 2.6.32 support
...
SVN-Revision: 31510
2012-04-29 07:36:37 +00:00
aa48f1326b
adm5120: switch to 3.3.3
...
SVN-Revision: 31509
2012-04-29 07:36:36 +00:00
a1a0f67748
adm5120: fix macronix bootloc patch
...
SVN-Revision: 31508
2012-04-29 07:36:35 +00:00
8e06682fb7
ramips: rt305x: extract wifi eeprom and use the 8M template for the UR-336UN
...
Patch-by: Lebedev Dmitry <lebedev@trendnet.ru>
SVN-Revision: 31507
2012-04-29 07:36:33 +00:00
1a0ef04231
adm8668: merge 3.3 fixes
...
SVN-Revision: 31497
2012-04-28 10:41:43 +00:00
87ae19eaa3
adm8668: nuke 2.6.36 support
...
SVN-Revision: 31496
2012-04-28 10:39:47 +00:00
9a7e9e76a3
adm8668: switch to 3.3
...
SVN-Revision: 31495
2012-04-28 10:38:53 +00:00
e047cf1899
switch to gpio-keys-polled
...
SVN-Revision: 31491
2012-04-27 16:44:48 +00:00
af2b3518af
linux/3.3: yet another missing symbol
...
SVN-Revision: 31488
2012-04-27 06:31:43 +00:00
d7b7b99d6e
brcm47xx: BCMA - Modified PCI CFG space access
...
The existing code (prior to the patch) does an "ioremap_nocache" on a
subset of a memory region that I think has already been mapped, and then
un-maps that smaller region when it is finished.
Thanks Nathan Hintz for the patch
SVN-Revision: 31481
2012-04-25 20:32:17 +00:00
d8c7ac8a8a
adm8668: add support for 3.3
...
SVN-Revision: 31480
2012-04-25 18:53:49 +00:00
7f09ba740a
adm8668: build gzip compressed uImage for testing
...
SVN-Revision: 31479
2012-04-25 18:53:48 +00:00
15d641eee1
adm8668: use a suffix for initramfs images
...
SVN-Revision: 31478
2012-04-25 18:53:46 +00:00
a447f1810c
ar71xx: enable MIB counters in the built-in switch of the AR934x
...
SVN-Revision: 31476
2012-04-25 13:02:11 +00:00
cad1fa359d
adm5120: remove 2.6.38 support
...
SVN-Revision: 31475
2012-04-25 12:57:35 +00:00
671361c7ea
adm5120: add 3.3 support
...
Partially based on the 3.1 patches by Hartmut Knaack <knaack.h [at] gmx.de>
SVN-Revision: 31474
2012-04-25 12:57:33 +00:00
43d67fa995
linux/3.3: fix compiler warnings in the plat_nand driver
...
SVN-Revision: 31473
2012-04-25 12:57:29 +00:00
4319d95842
adm5120: make 5GXi depends on CPU_LITTLE_ENDIAN
...
SVN-Revision: 31472
2012-04-25 12:57:26 +00:00
e90d3f1663
brcm47xx: A couple of other (inconsequential) BCMA patches
...
Noticed these while reviewing the code.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 31471
2012-04-24 21:56:42 +00:00
b07998cf11
brcm47xx: b44 fix workaround detection on some brcm47xx boards
...
Because of api change of nvram_getenv, the workaround failed to detect the hardware.
Based on patch by b.sander
Fixes #11268 .
SVN-Revision: 31470
2012-04-24 20:35:46 +00:00
8a38c62c07
bcm63xx: drop linux 3.2 support
...
SVN-Revision: 31464
2012-04-24 11:49:27 +00:00
77219290e1
bcm63xx: drop linux 3.0 support
...
SVN-Revision: 31463
2012-04-24 11:49:24 +00:00
49de6c1714
bcm63xx: switch kernel to 3.3
...
SVN-Revision: 31462
2012-04-24 11:49:19 +00:00
59b0c1b2b9
ar71xx: TL-WR741NDv4: add WLAN LED config
...
On TP-Link TL-WR741ND version 4, the WLAN LED must be configured to work.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 31461
2012-04-24 11:38:44 +00:00
8fd383ae2e
kernel: update linux 3.3 to 3.3.3
...
SVN-Revision: 31460
2012-04-24 09:25:38 +00:00
22b4e6b882
kernel: update linux 3.2 to 3.2.16
...
SVN-Revision: 31459
2012-04-24 09:25:35 +00:00
7ccf25f7da
kernel: add some more missing kernel config symbols
...
SVN-Revision: 31458
2012-04-24 09:25:32 +00:00
ed957f7c84
enable NF_CONNTRACK_PROCFS for Linux 3.3, required for /proc/net/nf_conntrack ( #11339 )
...
SVN-Revision: 31454
2012-04-24 00:55:57 +00:00
4b6833b176
x86: restore config-default, it is needed for 2.6.39
...
Reported-by: Thomas Heil <heil@terminal-consulting.de>
SVN-Revision: 31452
2012-04-23 16:56:08 +00:00
1ab80c7817
ramips: rt305x: add support for the UR-336UN board
...
Patch-by: Lebedev Dmitry <lebedev@trendnet.ru>
SVN-Revision: 31451
2012-04-23 16:56:06 +00:00
3626444c6d
ramips: rt305x: add support for the Asus WL-330N3G board
...
This patch adds support for the ASUS WL-330N3G
Comparing to the WL-330N, It have 32MB ram, usb support and a bicolor led.
The bi-color led is driven by 2 gpio.
I don't know how to handle this, so I simply made 2 leds : one red, one blue.
But the red light takes precedence over the blue one according to the chart below.
r = led is red
b = led is blue
0 = led is off
xy= x->r for red, b for blue led, y->value of brightness in /sys/class/leds/x/brughtness
initial state action led gpio state
r0 b0 r0->r1 r r0 b0
r0 b0 b0->b1 b r0 b1
r1 b0 r1->r0 0 r0 b0
r1 b0 b0->b1 r r1 *b1*
r1 b1 r1->r0 b r0 b1
r1 b1 b1->b0 r r1 b0
r0 b1 r0->r1 r r1 *b1*
r0 b1 b1->b0 0 r0 r0
Signed-off-by: Frédéric Leroy <fredo@starox.org>
SVN-Revision: 31450
2012-04-23 16:56:05 +00:00
34f4f4a0c5
switch to 3.3
...
SVN-Revision: 31448
2012-04-23 12:33:30 +00:00
9e054eb21a
add support for 3.3
...
SVN-Revision: 31447
2012-04-23 12:33:27 +00:00
460ef32930
switch to 3.3.2
...
SVN-Revision: 31446
2012-04-23 12:33:24 +00:00
5eeee1f80e
add 3.3 support
...
SVN-Revision: 31445
2012-04-23 12:33:19 +00:00
d4f3677cba
Adding wifi eeprom extract for ARV752DPW - Easybox 802
...
Signed-off-by: Christian Rustmeier <rustmeier a.t. gmail dotty com>
SVN-Revision: 31443
2012-04-23 09:40:37 +00:00
dcd185c2f8
ar8216: enable forwarding of multicast frames to the cpu port on ar8327 (thx, SeG)
...
SVN-Revision: 31441
2012-04-22 19:19:49 +00:00
858a50b41c
flexibity: Cleanup the subtarget config
...
SVN-Revision: 31440
2012-04-22 16:56:10 +00:00
6cd35fe3d3
tqma9263: update board definition for 3.x series and fix config choose
...
SVN-Revision: 31436
2012-04-22 09:09:53 +00:00
2852345af0
Remove old netus board definition
...
SVN-Revision: 31435
2012-04-22 09:09:50 +00:00
755b97303e
ep93xx: remove 2.6.39 support
...
SVN-Revision: 31434
2012-04-22 07:20:55 +00:00
631bf82241
amazon: remove 2.6.3{0,2} support
...
SVN-Revision: 31433
2012-04-22 07:20:53 +00:00
96b5d437d6
omap24xx: remove 2.6.38 support
...
SVN-Revision: 31426
2012-04-21 17:16:40 +00:00
76448ed5cf
xburst: remove 2.6.36 support
...
SVN-Revision: 31422
2012-04-21 17:03:10 +00:00
0cdd676554
malta: remove 2.6.39 and 3.0 support
...
SVN-Revision: 31421
2012-04-21 16:56:15 +00:00
0d148cb63b
mpc83xx: remove 2.6.32 support
...
SVN-Revision: 31420
2012-04-21 16:51:59 +00:00
884a4d47f0
octeon: remove 2.6.30 support
...
SVN-Revision: 31419
2012-04-21 16:45:32 +00:00
26b3cdad1c
cns3xxx: remove 2.6.31 support
...
SVN-Revision: 31418
2012-04-21 16:42:05 +00:00
b2b965a696
au1000: remove 2.6.39 support
...
SVN-Revision: 31416
2012-04-21 16:30:40 +00:00
f63d216467
x86: remove 2.6.32 support
...
SVN-Revision: 31415
2012-04-21 16:17:48 +00:00
bc2a7bfa70
ixp4xx: remove 2.6.3{2,8} and 3.0 support
...
SVN-Revision: 31414
2012-04-21 16:17:46 +00:00
50610aa869
linux/2.6.31: R.I.P.
...
SVN-Revision: 31412
2012-04-21 15:18:58 +00:00
2e5d3d2795
linux/2.6.30: R.I.P.
...
SVN-Revision: 31411
2012-04-21 15:18:55 +00:00
c6379f6295
linux: add broken flag to targets which are using 2.6.30
...
SVN-Revision: 31410
2012-04-21 15:18:54 +00:00
c627479641
linux/3.3: nuke the gpio_buttons patch
...
It is superseded by the in-kernel gpio-keys-polled driver.
SVN-Revision: 31409
2012-04-21 14:26:35 +00:00
2d91cb94ac
mpc52xx: nuke 3.2 config
...
SVN-Revision: 31408
2012-04-21 12:36:47 +00:00
0a83f90e21
mpc52xx: switch to 3.3.2
...
SVN-Revision: 31407
2012-04-21 12:36:45 +00:00
e904724726
mpc52xx: add kernel config for 3.3
...
SVN-Revision: 31406
2012-04-21 12:36:44 +00:00
5024ffb976
ramips: nuke 3.2 suport
...
SVN-Revision: 31405
2012-04-21 12:30:53 +00:00
6c8ca78067
ramips: switch to 3.3.2
...
SVN-Revision: 31404
2012-04-21 12:30:51 +00:00
5c325b0057
ramips: add support for 3.3
...
SVN-Revision: 31403
2012-04-21 12:30:50 +00:00
7f902c962b
ramips: rt305x: add OHCI/EHCI registration code for RT3352
...
SVN-Revision: 31402
2012-04-21 12:30:48 +00:00
1645928135
ramips: rt305x: fix CPU clock detection on RT3352
...
SVN-Revision: 31401
2012-04-21 12:30:47 +00:00
fb69e28eaf
ramips: rt305x: use different memory size setup for RT3352
...
SVN-Revision: 31400
2012-04-21 12:30:45 +00:00
818aeba960
ramips: rt3883: add profile and build sysupgrade image for the RT-N56U
...
SVN-Revision: 31399
2012-04-21 12:30:44 +00:00
6b677e1d22
ramips: add swconfig to the default package list
...
SVN-Revision: 31398
2012-04-21 12:30:43 +00:00
ced031a0b2
ramips: build initramfs image for the Fonera 2.0N
...
SVN-Revision: 31397
2012-04-21 12:30:42 +00:00
fc88a363c0
ramips: rt305x: add initial support for Tenda W306R V2.0
...
More device info at: http://wiki.openwrt.org/toh/tenda/w306r
Signed-off-by: David Pearce <David_18051985@hotmail.com.au>
[juhosg: fix checkpatch errors, remove kmod-phy and luci-ssl packages
from the profile, change broken GPIO number]
SVN-Revision: 31396
2012-04-21 12:30:40 +00:00
88b5827c52
ramips: remove hardcoded console parameter from kernel configs
...
SVN-Revision: 31395
2012-04-21 12:30:30 +00:00
1ffcaae700
linux/3.3: fix crypto4xx build failure
...
SVN-Revision: 31394
2012-04-21 10:47:04 +00:00
87cdc0dd5b
change /etc/config/network according to actual VLAN config to enable LAN port 4 on the ARV4520PW board
...
The VLAN mapping on the ARV4520PW board is the following:
port on Router: | VLAN in software:
LAN 1 | 3
LAN 2 | 2
LAN 3 | 1
LAN 4 | 0
DSL | 4
So LAN4 is not VLAN4 but VLAN0 (VLAN4 is DSL port) -> set "3 2 1 0 5t" as default switch config.
SVN-Revision: 31391
2012-04-21 08:07:21 +00:00
2624d67c08
ppc40x: nuke 3.2 support
...
SVN-Revision: 31387
2012-04-20 21:03:15 +00:00
f4833aa075
ppc40x: switch to 3.3.2
...
SVN-Revision: 31386
2012-04-20 21:03:14 +00:00
cfe4a6cb93
ppc40x: sync 3.3 config
...
SVN-Revision: 31385
2012-04-20 21:03:12 +00:00
9140d4ee44
ar71xx: remove duplicated AP121 Kconfig entry
...
SVN-Revision: 31382
2012-04-20 16:50:16 +00:00
ef54b5736d
cns21xx: remove 3.2 support
...
SVN-Revision: 31381
2012-04-20 15:25:00 +00:00
e667eb752b
cns21xx: switch to 3.3.2
...
SVN-Revision: 31380
2012-04-20 15:24:59 +00:00
d1af548557
cns21xx: add support for 3.3
...
SVN-Revision: 31379
2012-04-20 15:24:57 +00:00
434655d460
linux/3.3: update ARM mach-types
...
SVN-Revision: 31378
2012-04-20 15:24:54 +00:00
5c33f4e305
Add a missing symbol for config-3.3
...
Signed-off-by: Claudio Mignanti <c.mignanti@gmail.com>
SVN-Revision: 31373
2012-04-20 13:33:04 +00:00
701309ec11
Reorganize the subtargets, group subtargets per cpu family
...
Signed-off-by: Claudio Mignanti <c.mignanti@gmail.com>
SVN-Revision: 31372
2012-04-20 13:33:01 +00:00
3ac08ca653
Update the kernel to 3.3.x series, remove patches that doesn't apply anymore
...
Signed-off-by: Claudio Mignanti <c.mignanti@gmail.com>
SVN-Revision: 31371
2012-04-20 13:32:55 +00:00
f50231aeb3
Ensure that the bin directory exists before copy the files
...
Signed-off-by: Claudio Mignanti <c.mignanti@gmail.com>
SVN-Revision: 31370
2012-04-20 13:27:16 +00:00
147646fc66
remove some annoying warnings and fix snd modules build
...
SVN-Revision: 31365
2012-04-20 13:25:26 +00:00
eadf592371
add missing config symbol
...
SVN-Revision: 31364
2012-04-20 13:25:23 +00:00
da2cc2c79a
ar71xx: nuke 3.2 support
...
SVN-Revision: 31360
2012-04-19 21:32:05 +00:00
9854d6fb7f
ar71xx: switch to 3.3.2
...
SVN-Revision: 31359
2012-04-19 21:31:58 +00:00
a6b4b5fd6e
ar71xx: sync 3.3 config
...
SVN-Revision: 31358
2012-04-19 21:31:53 +00:00
ef97415b92
ar71xx: merge/reorganize 3.3 patches
...
SVN-Revision: 31357
2012-04-19 21:31:50 +00:00
408de85883
ar71xx: use ap91_pci_init for RB751{,G}
...
SVN-Revision: 31356
2012-04-19 21:31:48 +00:00
0a9832b50d
ar71xx: move USB device registration directly into rb751{,g}_setup
...
SVN-Revision: 31355
2012-04-19 21:31:43 +00:00
78967e6640
ar71xx: add ap9x_pci_get_wmac_data helper
...
SVN-Revision: 31354
2012-04-19 21:31:42 +00:00
5c9ca38e47
ar71xx: add sanity checks to decode_rle
...
Also use -EINVAL instead of -1.
SVN-Revision: 31353
2012-04-19 21:31:40 +00:00
8f921175ba
avr32: remove old kernel support
...
SVN-Revision: 31352
2012-04-19 21:23:07 +00:00
80705b9fb1
avr32: switch to 3.3.2
...
uClibc-0.9.33 causes segfaults at least in iptables.
The segfaults are present with 2.6.39 as well, so it
makes no sense to stick to that version.
SVN-Revision: 31351
2012-04-19 21:23:02 +00:00
abb57ea96f
avr32: sync kernel config
...
SVN-Revision: 31350
2012-04-19 21:22:50 +00:00
3108a4bb4b
avr32: fix atomic64_t related kernel build errors
...
SVN-Revision: 31349
2012-04-19 21:22:48 +00:00
26b3c31634
switch to 3.2.15
...
SVN-Revision: 31345
2012-04-18 15:36:33 +00:00
2e641b13c0
fix 335-mips-kexec patch for all 3+ kernels
...
SVN-Revision: 31344
2012-04-18 15:36:30 +00:00
d0bfc67e2e
kernel: x86: also update subtarget kernel versions
...
SVN-Revision: 31338
2012-04-17 21:01:43 +00:00
a8f2bc682e
kernel: also update the targets to use 3.2.15
...
Thanks Gabor for spotting it.
SVN-Revision: 31337
2012-04-17 13:12:14 +00:00
3a9b6dc313
kernel: update linux 3.3 to 3.3.2
...
SVN-Revision: 31336
2012-04-17 12:51:02 +00:00
ee4c47a134
kernel: update linux 3.2 to 3.2.15
...
SVN-Revision: 31335
2012-04-17 12:50:54 +00:00
a0f0213462
bump to Linux v3.3.1
...
SVN-Revision: 31314
2012-04-16 15:04:47 +00:00
9d11e3395a
Fix bufferbloat in PPPoATM TX queue
...
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SVN-Revision: 31313
2012-04-16 15:04:45 +00:00
2036c23faa
Update ppp TX restart patch to avoid race condition
...
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SVN-Revision: 31312
2012-04-16 15:04:44 +00:00
83948d6385
adds 3.3 patches and files
...
SVN-Revision: 31307
2012-04-16 12:31:48 +00:00
fb2b2b958e
backport missing platform data members for gpio-keys
...
SVN-Revision: 31306
2012-04-16 12:09:15 +00:00
e4f3867650
backport a missing eeprom 93cx6 define for building rt2x00
...
SVN-Revision: 31305
2012-04-16 12:09:13 +00:00
db728b6583
add missing debugging symbols
...
SVN-Revision: 31302
2012-04-16 11:38:35 +00:00
bb7cea7e65
add missing debugging symbols
...
SVN-Revision: 31301
2012-04-16 11:38:33 +00:00
c0ca7aed8e
mark set but unused variables as such
...
SVN-Revision: 31296
2012-04-15 18:53:48 +00:00
a70ad13a79
refresh 2.6.32 patches
...
SVN-Revision: 31295
2012-04-15 18:53:45 +00:00
47c8473475
refresh 2.6.32 patches
...
SVN-Revision: 31294
2012-04-15 18:53:42 +00:00
f2f5820d13
silence an annoying x86 warning
...
SVN-Revision: 31293
2012-04-15 18:53:39 +00:00
eb2191f5b0
at91: Missing kernel config symbols for AT91 target platform
...
I looked into buildbot snapshots and noticed that some platforms have
not successfully compiled for a long time. One example is at91, which
seems to be missing device-related kernel config symbols and the
snapshot build crashes already there.
Please find attached a patch that makes the at91 kernel config and
build to succeed again.
Signed off by: hannu.nyman@iki.fi
SVN-Revision: 31288
2012-04-15 09:50:51 +00:00
7475bb3dc6
brcm47xx: fix a bug in the sprom handling of bcma, this broke all bcma based SoCs.
...
bcma: use fallback sprom if no on chip sprom is available
SVN-Revision: 31285
2012-04-14 12:12:22 +00:00
62f0c3793b
kernel: refresh patches
...
SVN-Revision: 31279
2012-04-13 19:37:15 +00:00
6af575967c
kernel: update bcma and ssb to version master-2012-04-12 from wireless-testing
...
SVN-Revision: 31278
2012-04-13 19:35:40 +00:00
c75e700d42
brcm47xx: remove support for kernel 3.0
...
SVN-Revision: 31276
2012-04-13 16:53:16 +00:00
99768ccb7c
ixp4xx: add support for linux 3.3.1
...
SVN-Revision: 31275
2012-04-13 13:38:49 +00:00
ec667208e6
kernel: fix arm compressed images build on mac os x
...
SVN-Revision: 31274
2012-04-13 13:38:45 +00:00
4b230e19fc
PATCH: Disable console terminal in Grub for alix2 target
...
The alix2 target has the VGA console for grub enabled by default. This
prevents the grub menu from appearing on bootup. It is disabled by
default for the other embedded x86 platforms. This patch corrects that
behavior for the alix2 target.
Signed-off-by: Adam Gensler <openwrt@kristenandadam.net>
SVN-Revision: 31270
2012-04-12 23:30:27 +00:00
e3889bcf7c
update 3.2 patches
...
sync with lantiq kernel series
SVN-Revision: 31260
2012-04-12 12:33:56 +00:00
60a708edf1
remove preconfig variables
...
SVN-Revision: 31257
2012-04-12 09:43:43 +00:00
d558632955
remove preconfig variables
...
SVN-Revision: 31256
2012-04-12 09:43:41 +00:00
fcfdbd4961
add missing Kernel symbol spotted by buildbot
...
SVN-Revision: 31232
2012-04-10 10:09:27 +00:00
ed5abd5e4a
add missing symbols
...
SVN-Revision: 31231
2012-04-09 17:03:02 +00:00
50eba35cd3
kernel: update linux 3.3 to 3.3.1
...
SVN-Revision: 31223
2012-04-09 14:48:56 +00:00
16b4cbcdd6
kernel: update linux 3.2 to 3.2.14
...
SVN-Revision: 31222
2012-04-09 14:48:51 +00:00
1a57b05f47
kernel: add some more additional missing config symbols for 3.2 and 3.3
...
SVN-Revision: 31221
2012-04-09 14:48:46 +00:00
b0971e69f2
level up target xburst to linux kernel version 3.2.1
...
Thanks to the qi-hardware project - especially to Lars, Maarten and Xiangfu
SVN-Revision: 31218
2012-04-08 12:09:52 +00:00
f14fd53e3c
ar71xx: image: build initramfs images for the WHR boards
...
SVN-Revision: 31209
2012-04-06 06:45:08 +00:00
e295a077ce
ar71xx: initial support for Mikrotik RB751G-2HnD and RB751U-2HnD
...
Great collaboration on these two fantastic routers on the openwrt forum:
https://forum.openwrt.org/viewtopic.php?id=32320
Above all kudos to aryufan. Well done and thank you everyone else who
contributed.
To-Do: LED for wlan is not yet activated
To-Do: TxPower over 20dBm (RB751U) or 22dBm (RB751G) are not accepted by
the router
Signed-off-by: Hanno Schupp <hanno.schupp@gmail.com>
[juhosg: fix line wrapped patch, fix checkpatch errors, add missing
kernel patches]
SVN-Revision: 31208
2012-04-06 06:45:07 +00:00
fe6d66afe2
ar71xx: add rb750 to diag.sh
...
Support status led in diag.sh for RB750
Patch from: Evangelos Arkalis <arkalis.e@gmail.com>
SVN-Revision: 31207
2012-04-06 06:45:04 +00:00
da3f3f8f9d
add Easybox 802 - ARV752DPW
...
Implements the ARV752DPW architecture in mach-arv.c
Signed-off-by: Christian Rustmeier <rustmeier@gmail.com>
SVN-Revision: 31206
2012-04-05 20:03:21 +00:00
94af65db49
enable usb on dgn3500
...
A power-enable toggle gpio is not available, it is always on and protected with a resettable fuse.
Signed-off-by: Pieter Voorthuijsen<p.voorthuijsen at gmail.com>
SVN-Revision: 31205
2012-04-05 20:03:19 +00:00
b545c4b4fe
generic: use magic_long in sysupgrade
...
Signed-off-by: Matthias Bücher <mail@maddes.net>
SVN-Revision: 31200
2012-04-04 16:06:29 +00:00
930a820172
update wrt350nv2-builder to v2.4 and use new functionality for target orion_generic
...
Signed-off-by: Matthias Bücher <mail@maddes.net>
SVN-Revision: 31199
2012-04-04 16:06:25 +00:00
b47fc0f936
add support for D-Link DNS-323
...
this patch adds support for D-Link DNS323 storage device.
You can find more info here:
http://dns323.lukaperkov.net/
Currently you need serial cable to flash OpenWrt on DNS-323.
Signed-off-by: Luka Perkov < openwrt ->-to->- lukaperkov.net >
SVN-Revision: 31198
2012-04-04 15:53:55 +00:00
90e89bf4a9
add missing DM/MD config symbols
...
SVN-Revision: 31197
2012-04-04 15:53:52 +00:00
152f38a615
fix typos in adm5120 switch driver ( #4241 )
...
SVN-Revision: 31196
2012-04-04 15:53:15 +00:00
09ade17a15
add Edimax specific MAGIC_MAC_BASE to read MAC from flash ( #4241 ]
...
SVN-Revision: 31195
2012-04-04 15:53:12 +00:00
b180e0fb3b
fix support for 2.6.38 kernel
...
This patch fixes the following issues I encountered while compiling kernel 2.6.38.8 for my Omnima Embedded Controller/Edimax BR6104KP:
- kernel comes up with machine selection during build, even though everything was properly set in menuconfig
- USB api changes
Successfully built and tested with r29755.
Signed-off-by: Hartmut Knaack <knaack.h [at] gmx.de>
SVN-Revision: 31194
2012-04-04 15:53:09 +00:00
f087e07b5c
refresh 2.6.38 patches
...
SVN-Revision: 31193
2012-04-04 15:53:07 +00:00
db04bcb8e7
fix gcc-4.6 set but unused warnings
...
SVN-Revision: 31192
2012-04-04 15:53:04 +00:00
30f0cb476f
refresh patches
...
SVN-Revision: 31191
2012-04-04 15:53:01 +00:00
d87efd8c3c
kernel: update linux 3.2 to 3.2.13 and refresh patches
...
Also remove a duplicate patch from lantiq (already in generic).
SVN-Revision: 31158
2012-04-01 07:56:55 +00:00
1a395bd290
kernel: add some more missing kernel symbols for 3.2 and 3.3
...
SVN-Revision: 31157
2012-04-01 07:56:49 +00:00
400ab1802f
kernel: add some more missing serial 8250 config symbols
...
SVN-Revision: 31149
2012-03-30 08:11:01 +00:00
e9c4d3d1f2
ramips: add support for the ARC FreeStation5 board, also fix WCR-150GN network setup while we're at it - thanks Pau Escrich <p4u@dabax.net> for the implementation
...
SVN-Revision: 31144
2012-03-29 16:03:04 +00:00
de0527a354
brcm47xx: fix memory leak, backport from the mainline kernel
...
SVN-Revision: 31143
2012-03-29 15:44:06 +00:00
9992ce3a51
brcm47xx: add missing breaks into the nvram read code in the switch case statements
...
SVN-Revision: 31142
2012-03-29 15:43:16 +00:00
5f87ce9150
kernel: restore ebtables functionality by running netfilter hooks when the ebtables module is loaded
...
SVN-Revision: 31141
2012-03-29 14:15:54 +00:00
f7df1eafc4
bcm63xx: enable bcm6368 for linux 3.3 and build images
...
Only build bcm6368 images when building for linux 3.3.
SVN-Revision: 31133
2012-03-28 20:42:37 +00:00
c7ae2fccb6
bcm63xx: add initial support for bcm6368 boards
...
SVN-Revision: 31132
2012-03-28 20:42:34 +00:00
68f268a5eb
bcm63xx: add driver for the internal hw trng on bcm6368
...
SVN-Revision: 31131
2012-03-28 20:42:30 +00:00
78fb818f7c
bcm63xx: replace SPI driver with latest upstream version
...
SVN-Revision: 31130
2012-03-28 20:42:25 +00:00
a2adca6ee9
bcm63xx: add ethernet support for bcm6368
...
Add basic support for the internal ethernet switch on bcm6368. It behaves
as a dumb switch for now, but allows basic connectivity.
Also drop the ethernet patch for bcm6345 for now, it needs rework.
SVN-Revision: 31129
2012-03-28 20:42:20 +00:00
0876972850
bcm63xx: add missing bits from extirq support
...
Add missing external IRQ code parts for older chips in the new code.
SVN-Revision: 31128
2012-03-28 20:42:15 +00:00
44d546290a
bcm63xx: reorder patches
...
Reorder patches for a clearer distinction between the purposes of
the different patches.
SVN-Revision: 31127
2012-03-28 20:42:09 +00:00
13b6ec1d05
brcm47xx: update flash drivers
...
SVN-Revision: 31126
2012-03-28 17:03:18 +00:00
0ad9a02b9b
Revert commit 31091 - "[target/xburst] remove set but unused variable which leads into compiling errors with GCC >= 4.6.0"
...
'set-but-unused-variable'-issues are dealt with in a generic way now
SVN-Revision: 31124
2012-03-28 15:28:21 +00:00
b4508ce183
deal with 'set-but-unused-variables' in a more generic way
...
SVN-Revision: 31123
2012-03-28 15:28:13 +00:00
2f6e19e203
brcm47xx: BCMA - Consolidate/reduce code in bcma_device_name
...
Eliminate unneeded procedure by incorporating code into bcma_device_name
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 31120
2012-03-28 09:36:50 +00:00
a31a9b8650
brcm47xx: BCMA - Always map 4 bytes
...
This probably doesn't matter, but reads/writes are always 4 bytes, so always map 4 bytes.
Changes since v1: Moved changes to new patch file (234-bcma-always-map-4-bytes.patch).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 31119
2012-03-28 09:35:01 +00:00
b77217d963
ar71xx: boost SPI flash read performance
...
mtd_speedtest results:
page read speed
old new delta
DB120 929 KiB/s 2597 KiB/s +179.55%
TL-WR1043ND v1 754 KiB/s 2166 KiB/s +187.27%
TL-WR703N v1 745 KiB/s 2176 KiB/s +192.08%
TL-MR3220 v1 752 KiB/s 2154 KiB/s +186.44%
TL-WR2543ND v1 564 KiB/s 2130 KiB/s +277.66%
TL-WR741ND v2 525 KiB/s 1767 KiB/s +236.57%
ALFA-AP96 702 KiB/s 1977 KiB/s +181.62%
WNDR3700 697 KiB/s 1965 KiB/s +181.92%
SVN-Revision: 31118
2012-03-27 19:38:17 +00:00
102c6df148
ar71xx: improve SPI flash read/write performance
...
mtd_speedtest results:
page write speed
old new delta
DB120 209 KiB/s 226 KiB/s +8.13%
TL-WR1043ND v1 122 KiB/s 148 KiB/s +21.31%
TL-WR703N v1 153 KiB/s 194 KiB/s +26.80%
TL-MR3220 v1 130 KiB/s 156 KiB/s +20.00%
TL-WR2543ND v1 158 KiB/s 202 KiB/s +27.85%
TL-WR741ND v2 122 KiB/s 152 KiB/s +24.59%
ALFA AP96 229 KiB/s 260 KiB/s +13.54%
WNDR3700 202 KiB/s 223 KiB/s +10.40%
page read speed
old new delta
DB120 691 KiB/s 929 KiB/s +34.44%
TL-WR1043ND v1 372 KiB/s 754 KiB/s +102.69%
TL-WR703N v1 375 KiB/s 745 KiB/s +98.67%
TL-MR3220 v1 372 KiB/s 752 KiB/s +102.15%
TL-WR2543ND v1 307 KiB/s 564 KiB/s +83.71%
TL-WR741ND v2 315 KiB/s 525 KiB/s +66.67%
ALFA AP96 515 KiB/s 702 KiB/s +36.31%
WNDR3700 515 KiB/s 697 KiB/s +35.34%
SVN-Revision: 31117
2012-03-27 19:38:15 +00:00
6455178a6a
ar71xx: image: build initramfs images for more boards
...
SVN-Revision: 31116
2012-03-27 19:38:13 +00:00
e2bd975a2a
ar71xx: image: add MkuImage{Gzip,Lzma}/initramfs helpers
...
SVN-Revision: 31115
2012-03-27 19:38:11 +00:00
c7966a12b5
ar71xx: image: pass mtdlayout variables by value
...
SVN-Revision: 31114
2012-03-27 19:38:10 +00:00
692e47f49f
ar71xx: image: use MkuImageGzip in Image/Build/AthGzip/initramfs
...
SVN-Revision: 31113
2012-03-27 19:38:08 +00:00
6cd5fb7001
ar71xx: remove the built-in MTD map of the AP96 board
...
Pass the mtd_layout via the kernel command line instead.
SVN-Revision: 31112
2012-03-27 19:38:07 +00:00
61ee283899
ar71xx: remove the built-in MTD map of the PB92 board
...
Pass the mtd_layout via the kernel command line instead
SVN-Revision: 31111
2012-03-27 19:38:05 +00:00
1094dc1996
ar71xx: remove the built-in MTD map of the Zcomax devices
...
Pass the mtd_layout via the kernel command line instead.
SVN-Revision: 31110
2012-03-27 19:38:04 +00:00
24554ef187
ar71xx: reclaim the 'user_property' partition on WHR-* boards
...
SVN-Revision: 31109
2012-03-27 19:38:02 +00:00
87e4ec687b
ar71xx: remove the built-in MTD maps of several boards
...
We are passing the MTD layout via the kernel command line, so
it makes no sense to duplicate it in mach-* files. The patch
removes the built-in MTD maps of the following boards:
* AP113
* ALFA N2/N5
* DIR-600
* DIR-615
* DIR-825
* TEW-6{3,5}2BRP
* TEW-673GRU
* WHR-G301N
* WHR-HP-GN
* WHR-HP-G300N
SVN-Revision: 31108
2012-03-27 19:38:01 +00:00
e6b685650b
ar71xx: use modules for LED triggers
...
SVN-Revision: 31107
2012-03-27 19:37:59 +00:00
e28cd648b7
ar71xx: disable CONFIG_{I2C,SPI}_GPIO
...
SVN-Revision: 31104
2012-03-27 19:37:53 +00:00
6627f45a87
ar71xx: sync 3.3 config
...
SVN-Revision: 31103
2012-03-27 19:37:52 +00:00
f4d1e3d147
ar71xx: fix button polarity on TL-WR703N and TL-WR741N v4
...
SVN-Revision: 31102
2012-03-27 19:37:51 +00:00
d495277d9f
ramips: rt305x: build image for the DIR-615 rev D boards
...
Patch from #10105 .
SVN-Revision: 31101
2012-03-27 19:29:59 +00:00
e4e24c5512
ramips: rt305x: add add support for the Asus WL-330N board
...
[juhosg: reorder several lines in order to keep things sorted
alphabetically]
Signed-off-by: Frédéric Leroy <fredo@starox.org>
SVN-Revision: 31100
2012-03-27 19:29:57 +00:00
af2c5df66a
ppp: Fix high softirq utilization with pppoa
...
Users of the Geos platform are reporting high CPU utilization.
This seems to be rooted in a problem with the TX queue restart in PPP.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 31096
2012-03-27 17:47:44 +00:00
8de1475a27
add missing INET_UDP_DIAG symbol
...
SVN-Revision: 31095
2012-03-27 17:47:41 +00:00
60e195d399
geos: add 'tc' and kmod-sched for bonding
...
The Geos2 includes 2 ADSL+ interfaces, and as such it needs to have the TEQL scheduler for bonding.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 31094
2012-03-27 17:47:37 +00:00
a5abb08100
brcm47xx: update sprom patches like they are in the mainline kernel
...
SVN-Revision: 31093
2012-03-27 17:07:28 +00:00
ed8902d686
remove set but unused variable which leads into compiling errors with GCC >= 4.6.0
...
SVN-Revision: 31091
2012-03-27 16:29:19 +00:00
6fd915ba37
brcm47xx: update usb driver to the version send for mainline kernel integartion
...
SVN-Revision: 31089
2012-03-27 15:38:56 +00:00
5f799a0e97
ath9k: make endian check optional
...
Turns out it triggers on some AR71xx devices where no swapping should be done.
Enable endian check for the lantiq target.
SVN-Revision: 31084
2012-03-27 13:21:53 +00:00
b982e8166b
cleanup atheros wifi handling
...
Signed-off-by: Andrej Vlašić <andrej.vlasic0@gmail.com>
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31064
2012-03-25 08:50:38 +00:00
5ea100c39b
cleanup image makefile
...
SVN-Revision: 31063
2012-03-25 08:50:32 +00:00
f27c030141
update /etc/uci-defaults/*
...
SVN-Revision: 31062
2012-03-25 08:50:30 +00:00
ba4a7fca7b
update profiles
...
SVN-Revision: 31061
2012-03-25 08:50:27 +00:00
0f6a9d5c7c
bump kernel to 3.2.12
...
SVN-Revision: 31060
2012-03-25 08:50:09 +00:00
f35b9a9a4c
fixes breakage introduced in 776722ce36ac95877efb7fd771dde2f6ffc96433
...
SVN-Revision: 31054
2012-03-22 13:07:34 +00:00
1d2b19c4bf
Disable keyboard for x86 default config - revoke patch 30966
...
This was already fixed by commit 30309 and is part of generic x86 target.
SVN-Revision: 31052
2012-03-21 19:10:02 +00:00
ff5b7ef713
linux: refresh patches against 3.3
...
SVN-Revision: 31047
2012-03-20 15:55:07 +00:00
32e4801fb0
linux/3.{2,3}: yet another missing NET_VENDOR symbol
...
SVN-Revision: 31045
2012-03-20 15:55:04 +00:00
c8bf90d414
ar71xx: fix IRQ number for the AR7240 OHCI controller
...
SVN-Revision: 31044
2012-03-20 15:02:48 +00:00
bf96743548
base-files: gracefully handle empty variables in preinit ( #11155 )
...
SVN-Revision: 31030
2012-03-19 20:37:12 +00:00
c1dc6df8bd
kernel: update linux 3.2 to 3.2.12
...
SVN-Revision: 31028
2012-03-19 18:23:31 +00:00
f86e412389
ar71xx: disable unused file system drivers in the nand subtarget
...
SVN-Revision: 31027
2012-03-19 15:57:07 +00:00
b50cfe077c
ar71xx: sync kernel configs
...
SVN-Revision: 31026
2012-03-19 15:57:06 +00:00
8a2e4b49de
ar71xx: add initial support for RB750GL
...
SVN-Revision: 31025
2012-03-19 15:57:04 +00:00
d19f3dd512
ar71xx: make rb750_latch_change 'static void'
...
SVN-Revision: 31024
2012-03-19 15:57:03 +00:00
5348f46c80
ar71xx: add latch_change field to rb750_led_platform_data
...
SVN-Revision: 31023
2012-03-19 15:57:01 +00:00
8a471efe01
ar71xx: add platform data for the RB750 NAND driver
...
SVN-Revision: 31022
2012-03-19 15:56:59 +00:00
cb41fa7655
upgrade to 3.2, disable ppp by default until we figure out why ppp_generic breaks bootup
...
SVN-Revision: 31020
2012-03-19 11:27:34 +00:00
3fd38d99f2
add missing Kconfig symbols
...
SVN-Revision: 31019
2012-03-19 11:26:15 +00:00
e89df99083
ar71xx: use a different pll value on DB120
...
SVN-Revision: 31018
2012-03-19 11:11:22 +00:00
e9b45ebaba
ar71xx: add AR934x specific interface speed setup for ge0
...
SVN-Revision: 31017
2012-03-19 11:11:20 +00:00
6028889727
ar71xx: remove static MTD maps from AP121/DB120 boards
...
SVN-Revision: 31016
2012-03-19 11:11:19 +00:00
db6e326c56
targets: replace madwifi in profiles with ath5k, madwifi is unmaintained
...
SVN-Revision: 31015
2012-03-19 09:58:13 +00:00
6ac12fbb3c
ar71xx: use AR8327 on the DB120 board
...
SVN-Revision: 31012
2012-03-18 22:06:58 +00:00
faf82f3e10
generic: ar8216: add support for the AR8327 chip
...
SVN-Revision: 31011
2012-03-18 22:06:55 +00:00
fa7a83df4b
generic: ar8216: allow to use more ports
...
SVN-Revision: 31010
2012-03-18 22:06:51 +00:00
2ddbcb98ee
generic: ar8216: reorder chip specific functions
...
SVN-Revision: 31009
2012-03-18 22:06:48 +00:00
552cffd97a
generic: ar8216: reorder switch_dev specific functions
...
SVN-Revision: 31008
2012-03-18 22:06:45 +00:00
71e356029e
generic: ar8216: use ar8216_sw_ prefix for switchdev related functions
...
SVN-Revision: 31007
2012-03-18 22:06:42 +00:00
9a01936724
generic: ar8216: use switch_dev->ports in for loops
...
SVN-Revision: 31006
2012-03-18 22:06:40 +00:00
2ce9e4753c
generic: ar8216: add read_port_status field to ar8xxx_chip
...
SVN-Revision: 31005
2012-03-18 22:06:39 +00:00
01cad79e03
generic: ar8216: add init_globals field to ar8xxx_chip
...
SVN-Revision: 31004
2012-03-18 22:06:36 +00:00
56cacb3b21
generic: ar8216: add caps field to ar8xxx_chip
...
SVN-Revision: 31003
2012-03-18 22:06:33 +00:00
d1c585d4b1
generic: ar8216: add vtu_load_vlan field to ar8xxx_chip
...
SVN-Revision: 31002
2012-03-18 22:06:30 +00:00
332310fba2
generic: ar8216: add vtu_flush field to ar8xxx_chip
...
SVN-Revision: 31001
2012-03-18 22:06:26 +00:00
d964410cbc
generic: ar8216: add init_port field to ar8xxx_chip
...
SVN-Revision: 31000
2012-03-18 22:06:23 +00:00
006b3b846e
generic: ar8216: add setup_port field to ar8xxx_chip
...
SVN-Revision: 30999
2012-03-18 22:06:19 +00:00
eb5f0067b6
generic: ar8216: add hw_init field to ar8xxx_chip
...
SVN-Revision: 30998
2012-03-18 22:06:15 +00:00
a8371ad566
generic: ar8216: add a separate structure for chip specific stuff
...
Also add a hw_init function into that.
SVN-Revision: 30997
2012-03-18 22:06:12 +00:00
d18133b32d
generic: ar8216: rename chip field of struct ar8216
...
SVN-Revision: 30996
2012-03-18 22:06:08 +00:00
6e143e467f
generic: ar8216: move ar8216_id_chip function
...
Also remove the inline annotation.
SVN-Revision: 30995
2012-03-18 22:06:05 +00:00
1c99979b2c
generic: ar8216: rename ar8216_ops to ar8216_sw_ops
...
SVN-Revision: 30994
2012-03-18 22:06:03 +00:00
884f964e62
alix2: add require crypto kmods ( #10410 )
...
SVN-Revision: 30980
2012-03-18 18:56:02 +00:00
36e9a33df7
cns21xx: build uImage for the NS-K330
...
SVN-Revision: 30974
2012-03-18 12:07:56 +00:00
89babcf633
cns21xx: remove 2.6.3x support
...
SVN-Revision: 30973
2012-03-18 12:07:51 +00:00
776172531f
cns21xx: switch to 3.2.9
...
SVN-Revision: 30972
2012-03-18 12:07:50 +00:00
6dbe40f7d4
cns21xx: add support for 3.2
...
SVN-Revision: 30971
2012-03-18 12:07:48 +00:00
deac1c16a1
Enable keyboard for x86
...
This is required for qemu like descripted in
here http://wiki.openwrt.org/doc/howto/qemu
SVN-Revision: 30966
2012-03-17 21:32:08 +00:00
7b609a31be
kernel: improve profiling support, keep static symbols when profiling is enabled
...
SVN-Revision: 30964
2012-03-17 13:03:14 +00:00
9b60eb478a
remove support for old kernels
...
SVN-Revision: 30963
2012-03-17 11:55:59 +00:00
a2a18fe1ea
switch to 3.2
...
SVN-Revision: 30962
2012-03-17 11:55:56 +00:00
6e2c0fbe9f
add support for 3.2
...
SVN-Revision: 30961
2012-03-17 11:55:53 +00:00
9ef8de0e0a
add some more missing symbols
...
SVN-Revision: 30960
2012-03-17 11:55:49 +00:00
f601339e79
ar71xx: add profile and generate image for the JA76PF2 board
...
SVN-Revision: 30958
2012-03-16 18:00:40 +00:00
6036151187
ar71xx: add support for the jjPlus JA76PF2 board
...
SVN-Revision: 30957
2012-03-16 18:00:34 +00:00
a680662391
ar71xx: change LED name prefix on the jjplus boards
...
SVN-Revision: 30956
2012-03-16 18:00:26 +00:00
90279757bb
mpc52xx: switch to 3.2.9
...
SVN-Revision: 30955
2012-03-16 15:35:00 +00:00
dd0f928b14
kernel: optimize out remaining netfilter hooks in the bridging code if bridge filtering is disabled
...
SVN-Revision: 30954
2012-03-16 09:21:59 +00:00
b957208807
swconfig: use a mutex instead of a spinlock, many swconfig calls sleep
...
SVN-Revision: 30952
2012-03-15 19:32:31 +00:00
404a4c1fcd
ar8216: fix a MTU related regression
...
Switch reset on AR8316 appears to clobber the MTU configuration register
and possibly other global config registers. Move global configuration
register init writes back to the reset callback.
SVN-Revision: 30951
2012-03-15 16:57:27 +00:00
c00b53f3d0
ar71xx: move micrel PHY driver to the generic linux target
...
SVN-Revision: 30946
2012-03-15 09:25:53 +00:00
0011804302
linux/3.3: build mdio_register_board_info into the kernel if PHYLIB is selected
...
SVN-Revision: 30945
2012-03-15 09:25:49 +00:00
eb096bca59
linux/3.2: build mdio_register_board_info into the kernel if PHYLIB is selected
...
SVN-Revision: 30944
2012-03-15 09:25:47 +00:00
cee31ca238
brcm47xx: add support for NAND flash on devices using bcma
...
This patch add support for the NAND flash on BCM5357 based devices like the WNR3500Lv2.
Thank you Tathagata Das <tathagata@alumnux.com> for the patch
SVN-Revision: 30943
2012-03-14 22:59:39 +00:00
7fee567dc0
brcm47xx: move and rename the patches
...
The patches are now grouped by the part what they are doing and are using three digest numbers.
This does not remove or adds anything
SVN-Revision: 30942
2012-03-14 21:48:23 +00:00
fab5be9b4f
lantiq: load dwc_otg early
...
Needed for using external rootfs on usb sticks.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
SVN-Revision: 30940
2012-03-14 10:59:52 +00:00
e3af7c82f8
generic: ar8216: merge multiple if statements in ar8216_hw_apply
...
SVN-Revision: 30928
2012-03-13 17:33:12 +00:00
ff909edf94
ar71xx: ag71xx: fix ARP frame reception on AR934x switch ports
...
SVN-Revision: 30926
2012-03-13 17:29:38 +00:00
cd6a4cde13
ar71xx: ag71xx: start aneg on switch PHYs after reset
...
SVN-Revision: 30925
2012-03-13 17:29:37 +00:00
7c9534cfd7
ar71xx: ag71xx: poll PHY status of all available switch ports
...
SVN-Revision: 30924
2012-03-13 17:29:36 +00:00
8449eecf5f
ar71xx: ag71xx: allow to use port 5 of the AR934x built-in switch
...
SVN-Revision: 30923
2012-03-13 17:29:34 +00:00
1c5ac02a29
ar71xx: reset the switch on AR934x before ethernet device registration
...
SVN-Revision: 30922
2012-03-13 17:29:33 +00:00
17d3131d3c
ar71xx: fix a typo in ar71xx_regs.h
...
SVN-Revision: 30921
2012-03-13 17:29:31 +00:00
07486c4d96
remove udc patch since it is unused
...
SVN-Revision: 30920
2012-03-13 14:06:44 +00:00
b387cfd6e4
kernel: bypass all netfilter hooks if the sysctls for that functionality have been disabled - eliminates the overhead of enabling CONFIG_BRIDGE_NETFILTER in the kernel config
...
SVN-Revision: 30917
2012-03-13 10:06:45 +00:00
66df117d1b
ar71xx: use a dummy callback for interfaces with fixed speed
...
SVN-Revision: 30913
2012-03-12 20:38:58 +00:00
8b2b37ae58
ar71xx: merge ar934x_bo_ddr_flush patch
...
SVN-Revision: 30912
2012-03-12 20:38:57 +00:00
b0bb0793b9
ar71xx: enable UART function for early_printk/console
...
SVN-Revision: 30909
2012-03-12 17:32:39 +00:00
727a8c20c0
linux/3.3: refresh patches against 3.3-rc7
...
SVN-Revision: 30908
2012-03-12 17:32:38 +00:00
18f7081e17
ramips: rt305x: add profile for the AZtech HW-5503G board
...
Patch from #11085 .
SVN-Revision: 30907
2012-03-12 17:29:06 +00:00
fdb175f909
linux/3.3: allow to set platform_data for phy devices
...
SVN-Revision: 30906
2012-03-12 16:28:01 +00:00
1f79bfec0b
linux/3.2: allow to set platform_data for phy devices
...
SVN-Revision: 30905
2012-03-12 16:28:00 +00:00
2c2c288a3c
linux/3.3: add missing config symbol
...
SVN-Revision: 30904
2012-03-12 16:27:58 +00:00
ccc939ebc0
ar71xx: remove a 3.3 patch, it is already in 3.3-rc7
...
SVN-Revision: 30903
2012-03-12 16:27:57 +00:00
0814e61841
ar71xx: fix Compex WPE72 detection
...
SVN-Revision: 30902
2012-03-12 16:27:56 +00:00
0f77d0b2ba
ramips: add RT3350 detection
...
SVN-Revision: 30900
2012-03-12 16:12:13 +00:00
2dedd94d66
expose CONFIG_NETFILTER_NETLINK for external kmods
...
SVN-Revision: 30894
2012-03-12 00:09:23 +00:00
05d3f559f5
ramips: rt305x: rewrite SoC detection
...
SVN-Revision: 30890
2012-03-11 19:05:59 +00:00
8cf8ee8f9d
ramips: rt305x: rename SYSTEM_CONFIG_* defines to RT305X_SYSCFG_*
...
SVN-Revision: 30889
2012-03-11 19:05:57 +00:00
acb4ad86e5
ramips: replace RALINK_SOC_* macros with global variables
...
SVN-Revision: 30888
2012-03-11 19:05:56 +00:00
8cff770eb3
ramips: introduce ramips_soc_prom_init and move SoC detection into that
...
SVN-Revision: 30887
2012-03-11 19:05:53 +00:00
2149facb53
generic: ar8216: use usleep_range in ar8216_mii_{read,write}
...
msleep(1) can sleep for up to 20ms.
SVN-Revision: 30885
2012-03-11 17:19:14 +00:00
77d0a8ca85
generic: ar8216: add a helper function for writing PHY debug registers
...
SVN-Revision: 30884
2012-03-11 16:49:35 +00:00
dad19ac8b2
generic: ar8216: add lockep assertion to ar8216_rmw
...
SVN-Revision: 30883
2012-03-11 16:49:33 +00:00
6c51c47962
ramips: build initramfs image for DIR-{3,6}00 boards
...
SVN-Revision: 30882
2012-03-11 16:39:31 +00:00
f400a9cdd9
linux/3.3: show correct name for MIPS 24KEc in /proc/cpuinfo
...
SVN-Revision: 30881
2012-03-11 16:39:30 +00:00
c9d71c8387
linux/3.2: show correct name for MIPS 24KEc in /proc/cpuinfo
...
SVN-Revision: 30880
2012-03-11 16:39:28 +00:00
4e15457e0e
ramips: allow to use DSP ASE on RT3xxx
...
SVN-Revision: 30879
2012-03-11 16:39:26 +00:00
088dd4e879
ar71xx: stop image building if a loader is missing
...
SVN-Revision: 30877
2012-03-11 14:03:28 +00:00
067a065305
brcm47xx: make patch apply
...
SVN-Revision: 30876
2012-03-11 13:36:46 +00:00
7dcdf69388
brcm47xx: BCMA - Find names of non BCM cores
...
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 30875
2012-03-11 12:55:20 +00:00
d6d40b2d60
BCMA - Account for variable PCI memory base/size
...
Thank you Nathan Hintz for the patch
SVN-Revision: 30874
2012-03-11 12:52:43 +00:00
bbf739a59f
BCMA - Reorder SPROM fill
...
The SPROM is initialized in bcm47xx_fill_sprom, so move the call to bcm47xx_fill_sprom_ethernet after it.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 30873
2012-03-11 11:50:59 +00:00
1ad06d4c3a
generic: ar8216: coding style cleanup
...
SVN-Revision: 30857
2012-03-08 10:21:14 +00:00
e2d3cb69a1
generic: ar8216: don't use static variable in ar8236_hw_init
...
SVN-Revision: 30856
2012-03-08 10:21:12 +00:00
291e2dd583
generic: ar8216: move register inititalization into hw_init
...
SVN-Revision: 30855
2012-03-08 10:21:11 +00:00
e3538fa852
generic: ar8216: set chip type directly in ar8216_id_chip
...
SVN-Revision: 30854
2012-03-08 10:21:10 +00:00
a6c69e63b6
generic: ar8216: simplify ar8216_config_init
...
SVN-Revision: 30853
2012-03-08 10:21:08 +00:00
31584880bf
ar71xx: add watchdog driver to the default package list
...
SVN-Revision: 30852
2012-03-08 09:00:17 +00:00
127a2b1a4d
linux/3.{2,3}: even more NAND symbols
...
SVN-Revision: 30850
2012-03-07 22:32:54 +00:00
2d89fa7f43
ar71xx: fix WPS button polarity on TL-WR2543N
...
SVN-Revision: 30849
2012-03-07 19:50:53 +00:00
52a89cd95c
generic: ar8216: move port initialization into a separate function
...
SVN-Revision: 30848
2012-03-07 16:32:46 +00:00
0097cf7161
generic: ar8216: improve ar8216_wait_bit function
...
SVN-Revision: 30847
2012-03-07 16:32:45 +00:00
2370828599
generic: ar8216: use ar8216_read_port_link to get the CPU port link parameters
...
SVN-Revision: 30846
2012-03-07 16:32:43 +00:00
d8a8df51ca
generic: ar8216: use the generic get_port_link implementation
...
SVN-Revision: 30845
2012-03-07 16:32:42 +00:00
215e07177e
generic: rtl8367: use the generic get_port_link implementation
...
SVN-Revision: 30844
2012-03-07 16:32:40 +00:00
9e1be3b809
generic: rtl8366s: use the generic get_port_link implementation
...
SVN-Revision: 30843
2012-03-07 16:32:38 +00:00
e2f0264afe
generic: rtl8366rb: use the generic get_port_link implementation
...
SVN-Revision: 30842
2012-03-07 16:32:37 +00:00
c455a0f7be
ar71xx: ag71xx: fix get_port_link callback
...
SVN-Revision: 30841
2012-03-07 16:32:35 +00:00
5a83b3a5c7
ar71xx: ag71xx: use the generic get_port_link implementation
...
SVN-Revision: 30840
2012-03-07 16:32:34 +00:00
759c341e68
generic: swconfig: add a generic get_port_link implementation
...
SVN-Revision: 30839
2012-03-07 16:32:33 +00:00
fc9db6f410
generic: ar8216: use mdiobus_write in ar8236_hw_init
...
SVN-Revision: 30838
2012-03-07 16:32:31 +00:00
7112130105
generic: ar8216: use bus->mdio_lock directly in ar8216_mii_{read,write}
...
SVN-Revision: 30837
2012-03-07 16:32:30 +00:00
a31e090255
generic: ar8216: fix phy driver name
...
SVN-Revision: 30836
2012-03-07 16:32:28 +00:00
9a047b52d4
enable EFI partition support by default, adds ca. 8K uncompressed on ar71xx ( #8672 )
...
SVN-Revision: 30835
2012-03-07 14:14:52 +00:00
f03e7f2c7a
linux/3.2: fix crypto4xx build failure
...
SVN-Revision: 30834
2012-03-07 11:57:49 +00:00
43a20aa4c6
linux/3.1: add missing NAND symbols
...
SVN-Revision: 30827
2012-03-05 18:01:54 +00:00
bdcbf426ee
linux/3.0: add missing NAND symbols
...
SVN-Revision: 30826
2012-03-05 18:01:52 +00:00
1029786936
remove 3.1 support
...
SVN-Revision: 30823
2012-03-05 16:50:42 +00:00
75b5f4a6b4
rename 96348GW-1{0,1}-gen to 96348GW-1{0,1}-generic
...
SVN-Revision: 30822
2012-03-05 14:49:34 +00:00
c327915156
generate generic images for BCM96358VW and BCM96358VW2 ( #10666 )
...
SVN-Revision: 30821
2012-03-05 14:49:31 +00:00
ca1e59660e
wire bcm96348gw-10 reset button ( #10854 )
...
SVN-Revision: 30820
2012-03-05 14:23:45 +00:00
631a035a76
Merge branch 'bcm63xx'
...
SVN-Revision: 30819
2012-03-05 13:29:54 +00:00
63a1a106fb
kernel: fix powerpc unused-but-set variables
...
SVN-Revision: 30817
2012-03-05 00:51:12 +00:00
8821950069
kernel: remove the crtsavres dependency, the patched gcc will no longer emit references to that code
...
SVN-Revision: 30816
2012-03-05 00:51:08 +00:00
e308da91e7
kernel: fix vmalloc stack traces triggered by module with an empty init section (mostly happens on x86)
...
SVN-Revision: 30813
2012-03-05 00:12:44 +00:00
4b408b69ce
linux/3.3: add more NAND symbols
...
SVN-Revision: 30811
2012-03-04 18:23:59 +00:00
991cd3db2c
linux/3.2: add more NAND symbols
...
SVN-Revision: 30810
2012-03-04 18:23:56 +00:00
0e486d2fd2
ramips: add support for unbranded XDX-RN502J board
...
This patch adds support for routers using a PCB marked XDX-RN502J
V2.0, such as some unbranded routers like this:
http://www.mediafire.com/?8acv87h6snn9fj6
http://www.mediafire.com/?do7xonw7scor4kn
http://www.mediafire.com/?1ad49zvx3e7jyix
http://www.mediafire.com/?i46cqiq66maa197
http://www.aliexpress.com/product-fm/516397994-Free-Shipping-300M-3G-WAN-Wireless-N-WiFi-USB-AP-Router-2-Antennas-wholesalers.html
some reports also state the Aceex 22Y uses the same board.
more information can be found in the following openwrt forum post
https://forum.openwrt.org/viewtopic.php?id=34878
[juhosg: fix checkpatch warnings, use the GENERIC_4M template]
Signed-off-by: bruno schwander <bruno@tinkerbox.org>
SVN-Revision: 30809
2012-03-04 16:09:13 +00:00
44c8b396f9
ramips: board support for Asus RT-N10+
...
[juhosg: fix indentation in platform scripts, and remove debug
messages from 06_set_iface_mac]
Signed-off-by: Patrick van Staveren <trick@vanstaveren.us>
SVN-Revision: 30808
2012-03-04 16:09:11 +00:00
be4e5a29a9
ppc40x: preliminary support for 3.3
...
SVN-Revision: 30804
2012-03-04 12:39:46 +00:00
4daa2c31dc
linux/3.3: add missing config symbols
...
SVN-Revision: 30803
2012-03-04 12:39:44 +00:00
01832303ff
linux/3.2: add missing NAND symbols
...
SVN-Revision: 30802
2012-03-04 12:39:42 +00:00
86d852927e
ar71xx: refresh patches against 3.3-rc5
...
SVN-Revision: 30801
2012-03-03 14:10:29 +00:00
da628121b0
linux/3.3: merge recent ubifs patches from 3.2
...
SVN-Revision: 30800
2012-03-03 14:10:27 +00:00
419d9e2f54
linux/3.3: refresh patches against 3.3-rc5
...
SVN-Revision: 30799
2012-03-03 14:10:24 +00:00
d5ec28c734
omap24xx: fix compile error with new binutils ( #11072 )
...
SVN-Revision: 30798
2012-03-03 12:00:48 +00:00
632db63ed0
linux/3.2: add symlink xattr support to ubifs
...
SVN-Revision: 30794
2012-03-02 23:09:00 +00:00
5202e9908b
linux/3.2: add XZ decompression support to ubifs
...
SVN-Revision: 30793
2012-03-02 23:08:59 +00:00
b8bc1eca45
linux/3.2: add XZ decompressor support to crypto
...
SVN-Revision: 30792
2012-03-02 23:08:56 +00:00
5a471e23ad
ppc40x: switch to 3.2.9
...
SVN-Revision: 30791
2012-03-02 18:04:02 +00:00
ec9fd1f7a8
linux/3.2: add a bunch of missing symbols
...
SVN-Revision: 30790
2012-03-02 18:04:01 +00:00
b98f798df4
ppc40x: fix build errors in the CF and ISP116X drivers
...
SVN-Revision: 30789
2012-03-02 18:03:59 +00:00
dcbeaed9a0
mark variables as might be unused
...
SVN-Revision: 30787
2012-03-02 13:23:38 +00:00
2dc1c8ac70
remove unused variables and defines
...
SVN-Revision: 30786
2012-03-02 13:23:35 +00:00
7f88380664
MIPS: fix kexec build on 64-bits targets
...
SVN-Revision: 30785
2012-03-02 13:19:13 +00:00
c31b597763
refresh patches
...
SVN-Revision: 30784
2012-03-02 13:19:10 +00:00
90481d9b3a
MIPS: fix printing of size_t arg
...
SVN-Revision: 30783
2012-03-02 13:19:08 +00:00
112d6c7b74
MIPS: mark unused variables
...
SVN-Revision: 30782
2012-03-02 13:19:05 +00:00
c203860016
refresh patches
...
SVN-Revision: 30781
2012-03-02 13:19:02 +00:00
0d3f5b980e
MIPS: mark unused variables
...
SVN-Revision: 30780
2012-03-02 13:19:00 +00:00
b8f7592a92
refresh patches
...
SVN-Revision: 30779
2012-03-02 13:18:56 +00:00
cd3b60c14c
MIPS: mark unused variables
...
SVN-Revision: 30778
2012-03-02 13:18:53 +00:00
c25f266680
refresh patches
...
SVN-Revision: 30777
2012-03-02 13:18:47 +00:00
7052847972
ar71xx: ag71xx: keep VLAN tags if VLAN is not enabled
...
SVN-Revision: 30768
2012-03-01 19:49:05 +00:00
9698a499b6
kernel: update linux 3.2 to 3.2.9
...
SVN-Revision: 30767
2012-03-01 19:49:02 +00:00
12537aa190
brcm47xx: use kernel 3.2 by default
...
SVN-Revision: 30751
2012-02-28 20:12:46 +00:00
e5b04d57ef
revert unrelated change in previous commit
...
SVN-Revision: 30738
2012-02-27 09:34:31 +00:00
47b27500cf
partly revert r30708, it breaks various arches
...
SVN-Revision: 30737
2012-02-27 09:33:36 +00:00
72599f0c61
ramips: don't read RAMIPS_RX_CALC_IDX0 register in the loop
...
SVN-Revision: 30733
2012-02-26 10:54:13 +00:00
100f76a010
ramips: raeth: add rx_info structure
...
This helps to reduce code size on RX path:
add/remove: 0/0 grow/shrink: 3/1 up/down: 68/-56 (12)
function old new delta
ramips_eth_open 1104 1144 +40
ramips_ring_free 212 232 +20
ramips_eth_stop 400 408 +8
ramips_eth_rx_hw 648 592 -56
SVN-Revision: 30732
2012-02-26 10:54:12 +00:00
32e7b1c7d9
ramips: raeth: add tx_info structure
...
This helps to reduce code size on TX path:
add/remove: 0/0 grow/shrink: 1/4 up/down: 56/-92 (-36)
function old new delta
ramips_eth_open 1048 1104 +56
ramips_eth_tx_housekeeping 156 148 -8
ramips_ring_free 224 212 -12
ramips_eth_stop 420 400 -20
ramips_eth_hard_start_xmit 480 428 -52
SVN-Revision: 30731
2012-02-26 10:54:10 +00:00
8b91bad57e
ixp4xx: fix a compile error
...
SVN-Revision: 30728
2012-02-25 22:12:11 +00:00
fe66f30aae
add some missing 2.6.39 kernel symbols observed on x86/generic builds
...
SVN-Revision: 30718
2012-02-25 13:17:32 +00:00
bafdae9233
enable RTC_CLASS for Linux 3.2 and 3.3
...
SVN-Revision: 30717
2012-02-25 13:06:26 +00:00
30143b715c
ramips: raeth: don't process disabled interrupts
...
Also rename the 'fe_int' variable.
SVN-Revision: 30713
2012-02-25 11:59:19 +00:00
6b37484883
ar71xx: use v6.0.0 in UBTN-XM firmwares ( closes #11038 )
...
SVN-Revision: 30712
2012-02-24 20:41:38 +00:00
6990f66861
ramips: fix FONERA20N image generation
...
SVN-Revision: 30710
2012-02-24 16:18:46 +00:00
74db55a982
config: deprecated symbol CONFIG_LEDS_GPIO_PLATFORM
...
CONFIG_LEDS_GPIO_PLATFORM went away a while ago.
http://git.kernel.org/?p=linux/kernel/git/stable/linux-stable.git;a=commit;h=2bcc7ed5b83b0a59c6976476e8788675038fb11b
Also, most platforms comment out CONFIG_LEDS_GPIO but not x86 for some reason.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 30708
2012-02-24 10:35:20 +00:00
9afeeae65e
ramips: image: increase minimum kernel partition size to 896k
...
SVN-Revision: 30706
2012-02-23 19:58:16 +00:00
7089b5213e
ramips: image: cleanup and sort templates/profiles
...
SVN-Revision: 30705
2012-02-23 19:58:15 +00:00
c8718a220b
ramips: image: use GENERIC_4M template for the ALL0256N board
...
SVN-Revision: 30704
2012-02-23 19:58:14 +00:00
507c7d30f5
ramips: image: introduce mkmtd/{,phys,spi} helpers
...
SVN-Revision: 30703
2012-02-23 19:58:12 +00:00
5f63ea18aa
ramips: image: pass mtdlayout variables by value
...
SVN-Revision: 30702
2012-02-23 19:58:11 +00:00
49e53c06b9
ramips: image: merge F5D8235V{1,2} templates
...
SVN-Revision: 30701
2012-02-23 19:58:10 +00:00
00e7277a4c
ramips: image: use generic template for the WR6202, OMNIEMB, W502U boards
...
SVN-Revision: 30700
2012-02-23 19:58:07 +00:00
554010d55b
ramips: image: introduce mkcmdline helper
...
SVN-Revision: 30699
2012-02-23 19:58:06 +00:00
32c6d63acf
ramips: image: use the GENERIC_4M template for the V11ST-FE board
...
SVN-Revision: 30698
2012-02-23 19:58:04 +00:00
ab65053cf0
ramips: image: simplify Makefile a bit
...
SVN-Revision: 30697
2012-02-23 19:58:03 +00:00
9017fce3a2
ramips: image: add MkImageLzma wrapper
...
SVN-Revision: 30696
2012-02-23 19:58:02 +00:00
c9d8f471fc
ramips: image: allow to build board specific initramfs images
...
SVN-Revision: 30695
2012-02-23 19:58:01 +00:00
b168535b10
drop backported patches as they cause regressions and oopses
...
SVN-Revision: 30690
2012-02-23 07:42:04 +00:00
e5798d7c9b
fixes etop locking issue
...
SVN-Revision: 30689
2012-02-23 07:42:00 +00:00
c0974b46a5
ramips: merge identical switch configuration entries
...
SVN-Revision: 30688
2012-02-22 19:46:19 +00:00
a9101a144c
ramips: use unified switch identifiers in uci-defaults/network
...
SVN-Revision: 30687
2012-02-22 19:46:17 +00:00
b6522f372f
ramips: fix VLAN config of the RT-N15
...
SVN-Revision: 30686
2012-02-22 19:46:15 +00:00
a18a821733
ramips: raeth: show interrupt statistics in debugfs
...
SVN-Revision: 30681
2012-02-22 13:06:44 +00:00
214216c04d
ramips: raeth: add debugfs support
...
SVN-Revision: 30680
2012-02-22 13:06:42 +00:00
c1e4d709fa
ramips: raeth: rename main source file
...
SVN-Revision: 30679
2012-02-22 13:06:41 +00:00
5e6bc97d0c
ramips: raeth: add missing Kconfig and Makefile
...
SVN-Revision: 30671
2012-02-21 09:44:30 +00:00
3ba0f4e1ca
ramips: move the ethernet driver into a separate directory
...
Also clean up the Kconfig symbols.
SVN-Revision: 30670
2012-02-21 09:26:43 +00:00
a6d904b1d6
ramips: rename the spi driver
...
SVN-Revision: 30669
2012-02-21 09:26:41 +00:00
c918810414
ar71xx: switch to kmod-gpio-button-hotplug
...
SVN-Revision: 30660
2012-02-20 10:51:48 +00:00
058d331a39
kernel: strip unnecessary symbol table information from kernel modules, reduces default squashfs size on ar71xx by about 4k
...
SVN-Revision: 30657
2012-02-20 09:03:17 +00:00
dd001a4b0f
ramips: rt3883: make rt3883_nand_data visible
...
SVN-Revision: 30655
2012-02-19 19:40:37 +00:00
62f213eab9
ramips: merge 3.2 fixes
...
SVN-Revision: 30652
2012-02-19 17:52:23 +00:00
18fdaee00b
ramips: nuke 2.6.39 support
...
SVN-Revision: 30651
2012-02-19 17:52:20 +00:00
e2ea72515f
ramips: rt305x: nuke built-in MTD partition maps
...
SVN-Revision: 30650
2012-02-19 17:52:15 +00:00
de6405c898
ramips: rt288x: nuke built-in MTD partition maps
...
SVN-Revision: 30649
2012-02-19 17:52:11 +00:00
e7f59b9326
ramips: build sysupgrade image for the V11ST-FE board
...
SVN-Revision: 30648
2012-02-19 17:52:08 +00:00
3489515a7e
ramips: rt305x: add support for the Skyline SL-R7205 Wireless 3G router
...
[juhosg:
- don't switch back to 2.6.39
- update config-3.2
- change machine id to SL-R7205
- reorder case entries in platform scripts
- remove button hotplug script]
Signed-off-by: Haipoh Teoh <hpteoh@ceedtec.com>
SVN-Revision: 30645
2012-02-19 16:44:49 +00:00
5dec9dd3b2
brcm47xx: add code to generate images for some netgear devices
...
This is commented out until we get report of working devices.
SVN-Revision: 30639
2012-02-18 23:21:47 +00:00
1122b231f9
brcm47xx: sprom for nvram parsing
...
This adds support for parsing sprom form nvram for sprom version form 1 to 9.
It also adds sprom from nvram support for devices on the bcma bus.
SVN-Revision: 30638
2012-02-18 23:08:26 +00:00
990ed96a2a
ralink: rt3883: disable the 2GHz band on the RT-N56U
...
SVN-Revision: 30632
2012-02-18 17:36:21 +00:00
5710530c41
ramips: rt3883: make rt3883_wlan_data visible
...
SVN-Revision: 30631
2012-02-18 17:36:16 +00:00
799e9cbec8
generic: add disable_[25]ghz to struct rt2x00_platform_data
...
SVN-Revision: 30630
2012-02-18 17:36:13 +00:00
3d20de331d
ar71xx: fix image signature for UBNT-XM boards
...
SVN-Revision: 30626
2012-02-18 14:45:52 +00:00
383008635a
generic/2.6.37: fix 'set but unused' build errors on MIPS
...
SVN-Revision: 30615
2012-02-17 17:21:03 +00:00
e17a3ffbbd
ramips: extract eeprom for the built-in wlan module on the RT-N56U
...
SVN-Revision: 30604
2012-02-16 20:06:22 +00:00
dabca24361
ramips: rt3883: change eeprom file name
...
SVN-Revision: 30603
2012-02-16 20:06:21 +00:00
eed8e2a4fd
Disable by default padding of images
...
SVN-Revision: 30590
2012-02-16 17:54:07 +00:00
8676e49d9d
Allow gzipping of squashfs images with padded jffs2 partition
...
SVN-Revision: 30589
2012-02-16 17:54:04 +00:00
ab09db09fc
GZip only ext4 and padded images
...
SVN-Revision: 30588
2012-02-16 17:54:01 +00:00
b4f51343c6
Make gzipping of images configurable via menuconfig
...
SVN-Revision: 30587
2012-02-16 17:53:57 +00:00
3004f30f01
ar71xx: remove duplicated define from the D-Link profile
...
SVN-Revision: 30577
2012-02-16 09:03:27 +00:00
00d963999d
ramips: select HW_HAS_PCI on per-board basis
...
SVN-Revision: 30576
2012-02-16 08:17:54 +00:00
fc967295ec
ramips: rt3883: remove a stray character from rt3883.h
...
SVN-Revision: 30575
2012-02-16 08:17:53 +00:00
b4af07d5c0
ramips: rt288x: don't register the PCI controller on each board
...
SVN-Revision: 30574
2012-02-16 08:17:52 +00:00
f8a56dc8df
ramips: raeth: separate ring allocation and setup
...
SVN-Revision: 30573
2012-02-16 08:17:50 +00:00
d186c17aa6
generic: add SND_PPC symbol
...
SVN-Revision: 30572
2012-02-16 07:51:44 +00:00
1bb8a7613e
Add Ubiquiti UniFi Profile; It's an AP without USB so don't include USB drivers by default
...
SVN-Revision: 30571
2012-02-16 07:45:28 +00:00
b797f72319
d-link: Add DIR-601 Profile Definition; It needs different factory images than DIR-600
...
SVN-Revision: 30570
2012-02-16 07:38:33 +00:00
c736e2d4b0
Fix partitions for Cameo-based boards; kernel 3.2 is bigger
...
SVN-Revision: 30569
2012-02-16 07:29:26 +00:00
4685a51301
image: For Cameo-based board fix adding mtd layout to kernel commandline)
...
SVN-Revision: 30568
2012-02-16 07:24:45 +00:00
8dc1ff6cb1
linux 3.2: missing generic symbols
...
These symbols are dependent on CONFIG_PCI being enabled.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 30565
2012-02-15 23:37:47 +00:00
49fc54be3d
ramips: rt288x: fix PCI resource conflict
...
SVN-Revision: 30563
2012-02-15 21:19:02 +00:00
37f8c19028
correct PCI IO/Mem resource swapping
...
SVN-Revision: 30562
2012-02-15 21:13:21 +00:00
3ceebbba14
add Ralink V11ST-FE board support
...
This board is equipped with:
- 4MB of NOR Flash
- 32MB of SDRAM
- IC+ IP175C switch
- one Mini-PCI slot
SVN-Revision: 30561
2012-02-15 21:13:11 +00:00
8b8d9a8336
ramips: raeth: add a helper function for skb allocation
...
SVN-Revision: 30555
2012-02-15 18:33:42 +00:00
e57546de83
ramips: raeth: use netdev_alloc_skb
...
SVN-Revision: 30554
2012-02-15 18:33:41 +00:00
064855314b
ramips: raeth: add '__packed __aligned(4)' annotation to dma descritor structures
...
This helps GCC to generare more efficient code.
SVN-Revision: 30553
2012-02-15 18:33:40 +00:00
8c95385d78
ramips: raeth: use 're' instead of 'priv' everywhere
...
SVN-Revision: 30552
2012-02-15 18:33:38 +00:00
b3b79365f3
ramips: raeth: force link down in ramips_phy_stop
...
SVN-Revision: 30550
2012-02-15 13:47:52 +00:00
3e7b461431
ramips: raeth: serialize ramips_link_adjust calls
...
SVN-Revision: 30549
2012-02-15 13:47:50 +00:00
dcb13d4098
ramips: raeth: add PHYLIB support
...
SVN-Revision: 30547
2012-02-15 06:47:12 +00:00
23b2bd9494
linux-atm: update solos-pci driver to upstream
...
Fixes for the solos-pci driver.
- Corrects calculation of headroom for padding.
- Removes pointless debug messages.
- Expose Bis A and Bis M annex capabilities.
- Expose hardware revision.
Signed-off-by: Philip Prindeville <philipp_subx@redfish-solutions.com>
SVN-Revision: 30541
2012-02-14 20:11:24 +00:00
9e5b8ad833
linux-atm: headroom/padding fixes
...
Submitted upstream to netdev by Chas Williams on linux-atm.
Signed-off-by: Philip Prindeville <philipp_subx@redfish-solutions.com>
SVN-Revision: 30540
2012-02-14 20:11:22 +00:00
1a71f07d00
generate uboot environment data in target
...
With this patch it is possible to generate uboot environment config file
inside lantiq target. Currently it is only supporting GIGASX76X board.
uboot environment config is used by fw_printenv fw_setenv tools.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 30537
2012-02-14 19:07:11 +00:00
7416a5f0aa
fix compile error in previous commit
...
SVN-Revision: 30534
2012-02-14 19:07:05 +00:00
cd1a204365
Support booting the Speedport W502V using BRN-BOOT.
...
While the disadvantage is less available flash space, it's easy and
safe to flash without opening the device.
Going back to the original firmware is also possible.
This patch add two firmware utilities, mkbrncmdline and mkbrnboot.
mkbrncmdline patches the uncompressed kernel so the registeres a0 to
a3 are initialized and the memory size is passed in.
mkbrnboot takes the lzma compressed kernel and squashfs images and
creates a firmware image that can be flashed using the BRN-BOOT
recovery kernel, which is booted by holding both buttons when
powering up the device and will listen on http://192.168.2.1 .
The firmware file from bin/lantiq/ to use is
openwrt-lantiq-danube-ARV4525PW-BRNDTW502-brnImage
The BRN-BOOT recovery kernel does size-check the image, so if it's
too big to fit into flash it will complain accordingly.
A second patch is needed to make the wired network interface work
since there is no u-boot to pre-initialise it.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 30532
2012-02-14 17:48:04 +00:00
02a01a16c7
ramips: extract eeprom for the PCIe wlan module on the RT-N56U
...
SVN-Revision: 30529
2012-02-14 17:32:45 +00:00
43d1a2c3ab
ramips: rt3883: enable PCI on the RT-N56U board
...
SVN-Revision: 30528
2012-02-14 17:32:44 +00:00
784be92e39
ramips: rt3883: add PCI support
...
SVN-Revision: 30527
2012-02-14 17:32:42 +00:00
10f00dc48b
ramips: rt3883: sync 2.6.39 config
...
SVN-Revision: 30526
2012-02-14 17:32:41 +00:00
ed79921fe5
ramips: use SoC specific irq.h
...
SVN-Revision: 30525
2012-02-14 17:32:40 +00:00
0b07769898
fixes irq locking in ethernet driver
...
SVN-Revision: 30522
2012-02-14 15:05:58 +00:00
55bf39e98c
fixes gpio_export patch
...
SVN-Revision: 30521
2012-02-14 15:05:57 +00:00
976d3eb854
add annex selection support to ltq_dsl package
...
SVN-Revision: 30518
2012-02-14 15:05:49 +00:00
9a0e17857e
ar71xx: add profile and build image for the TP-Link TL-WR842N/ND v1 boards
...
SVN-Revision: 30508
2012-02-13 17:11:58 +00:00
1c57a22aae
ar71xx: add model detection for TL-WR842N/ND
...
SVN-Revision: 30507
2012-02-13 17:11:57 +00:00
e16916480d
update to 3.2
...
SVN-Revision: 30503
2012-02-13 16:05:30 +00:00
7bed2e2225
fix titan gpio register size
...
SVN-Revision: 30502
2012-02-13 16:05:27 +00:00
8d5dfa75e6
ramips: rt3883: update package list in the default profile
...
SVN-Revision: 30499
2012-02-13 15:18:05 +00:00
99c019fb0d
ramips: add preliminary support for the Asus RT-N56U board
...
SVN-Revision: 30498
2012-02-13 15:18:04 +00:00
97e641a0e6
ramips: raeth: enable MDIO code for RT3883
...
SVN-Revision: 30497
2012-02-13 15:18:03 +00:00
e532fa5fd4
ramips: add preliminary support for the RT3662/RT3883 SoCs
...
SVN-Revision: 30495
2012-02-13 15:17:59 +00:00
4a0dc3a32a
add support for 3.2
...
SVN-Revision: 30492
2012-02-13 12:36:34 +00:00
30408f1cc4
brcm47xx: deactivate CONFIG_NO_HZ as it seams not to be needed.
...
SVN-Revision: 30488
2012-02-12 22:41:20 +00:00
e7bd7f7e85
brcm47xx: activate config bug to show warnings
...
SVN-Revision: 30487
2012-02-12 22:40:01 +00:00
22ec8b4839
ramips: use GENERIC_{4,8}M image template for WR5123GN
...
SVN-Revision: 30483
2012-02-12 18:04:47 +00:00
b7f129e19b
ramips: rt305x: pass MTD partition map to the ALL0256N via cmdline
...
SVN-Revision: 30482
2012-02-12 18:04:46 +00:00
fa21aef5ab
brcm47xx: refresh patches
...
SVN-Revision: 30481
2012-02-12 16:45:27 +00:00
838c363886
brcm47xx: update usb driver for brcm47xx.
...
SVN-Revision: 30480
2012-02-12 16:38:10 +00:00
a287c60a61
ramips: add initial support for 3.2
...
SVN-Revision: 30476
2012-02-12 12:52:14 +00:00
388013b0ce
ramips: include 'linux/module.h' in the ramips_spi driver
...
SVN-Revision: 30475
2012-02-12 12:52:13 +00:00
faae4235c4
ramips: rt288x: remove per-board physmap_flash_data instances
...
SVN-Revision: 30474
2012-02-12 12:52:12 +00:00
3502e2b93f
ramips: rt305x: remove per-board physmap_flash_data instances
...
SVN-Revision: 30473
2012-02-12 12:52:10 +00:00
143e861708
enable another l2 cache errate on newer kernels
...
SVN-Revision: 30472
2012-02-12 11:22:08 +00:00
3a11dcdaa8
ramips: load gpio-polled keys module
...
SVN-Revision: 30463
2012-02-11 20:37:34 +00:00
323ece9474
ramips: remove yet another CONFIG_MTD_PARTITION ifdef
...
SVN-Revision: 30462
2012-02-11 19:37:11 +00:00
32b9e8c750
ramips: use gpio-keys-polled instead of gpio-buttons
...
SVN-Revision: 30461
2012-02-11 19:37:06 +00:00
8ce80f7454
add some missing symbols
...
SVN-Revision: 30460
2012-02-11 18:38:28 +00:00
80b40497de
ramips: add MIPS platform file
...
SVN-Revision: 30459
2012-02-11 18:16:11 +00:00
80a535ba58
generic/2.6.39: refresh patches
...
SVN-Revision: 30458
2012-02-11 18:16:08 +00:00
440a7fbc3b
refresh patches to -rc3
...
SVN-Revision: 30456
2012-02-11 17:43:06 +00:00
4e1b870f3e
ramips: add MDIO bus support for RT288X
...
SVN-Revision: 30455
2012-02-11 16:49:56 +00:00
0ace4636db
rename 3.1 patches directory as it will be used for newer kernels as well
...
SVN-Revision: 30454
2012-02-11 15:59:23 +00:00
1fb5ff4e04
rename 2.6.39 patches directory
...
SVN-Revision: 30453
2012-02-11 15:58:14 +00:00
34a9ccf544
ramips: fix Belkin F5D8235-v2 VLAN setup
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 30452
2012-02-11 15:31:18 +00:00
8916c02b47
ramips: raeth: make debugging messages configurable
...
SVN-Revision: 30450
2012-02-11 15:12:10 +00:00
aac3ad4c0e
ramips: raeth: use device pointer in DMA API calls
...
SVN-Revision: 30449
2012-02-11 15:12:08 +00:00
1fd8724e94
ramips: raeth: add netdev pointer to private structure
...
SVN-Revision: 30448
2012-02-11 15:12:06 +00:00
c6fa11d00f
ramips: raeth: cleanup DMA API usage in ramips_eth_hard_start_xmit
...
SVN-Revision: 30447
2012-02-11 15:12:05 +00:00
2d055f130e
ramips: raeth: unmap rx DMA address in ramips_cleanup_dma
...
SVN-Revision: 30446
2012-02-11 15:12:04 +00:00
7bd7ddcf4e
ramips: raeth: add rx_dma array to store the DMA address of the rx packets
...
SVN-Revision: 30445
2012-02-11 15:12:02 +00:00
647af823d9
ramips: raeth: use dma_addr_t for the descriptors
...
SVN-Revision: 30444
2012-02-11 15:12:01 +00:00
df5892d1f1
ramips: raeth: unmap DMA memory when a packet is received
...
SVN-Revision: 30443
2012-02-11 15:11:56 +00:00
617954ca5d
ramips: raeth: add a temporary pktlen variable
...
SVN-Revision: 30442
2012-02-11 15:11:55 +00:00
d1d492eaf9
ramips: raeth: protect macro parameters
...
SVN-Revision: 30441
2012-02-11 15:11:50 +00:00
8250692359
ramips: raeth: indicate dropped packets in stats
...
SVN-Revision: 30440
2012-02-11 15:11:49 +00:00
c67adbbddb
ramips: raeth: use the NUM_TX_DESC for the tx_skb array
...
SVN-Revision: 30439
2012-02-11 15:11:47 +00:00
a2c8789578
ramips: use uncached address in detect_mem_size
...
SVN-Revision: 30438
2012-02-11 15:11:45 +00:00
ba4c9b3a8f
ramips: rt305x: remove CONFIG_MTD_PARTITION ifdefery from machine files
...
SVN-Revision: 30437
2012-02-11 15:11:43 +00:00
f2dd67dc09
ramips: rt288x: remove CONFIG_MTD_PARTITION ifdefery from machine files
...
SVN-Revision: 30436
2012-02-11 15:11:41 +00:00
d6b9f88743
ramips: refresh patches
...
SVN-Revision: 30435
2012-02-11 15:11:40 +00:00
9cde29f1a7
ramips: rt305x: add support for Accton WR6202 / SMCWBR11S-3GN
...
This patch adds support for the Accton WR6202 Mini 3G broadband router.
Full details for this device are available at
http://www.awbnetworks.com/products03.php?Fullkey=19 .
This device is identical to the SMCWBR11S-3GN:
http://www.smc-asia.com/products03.php?Fullkey=210
It's also worth noting that this board has a GPIO line to control the
power to the USB port.
[juhosg:
- fix checkpatch warnings,
- reorder Kconfig entry,
- merge the sysupgrade patch,
- add GPL header]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 30434
2012-02-11 15:11:36 +00:00
59b474732c
ramips: rt305x: merge duplicated mac address setup
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 30433
2012-02-11 15:11:34 +00:00
7298ef2456
ramips: rt305x: add profile for the Belkin f5d8235v2
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 30432
2012-02-11 15:11:32 +00:00
295a154f2f
brcm47xx: print the chip id and rev found by ssb and bcma
...
SVN-Revision: 30428
2012-02-10 22:42:43 +00:00
3708227f96
ar71xx: zero partition parser data in m25p80
...
Ths fixes parsing of RedBoot partitions.
SVN-Revision: 30427
2012-02-10 20:19:06 +00:00
0430194cc3
ramips: fix compiler warning in prom.c
...
SVN-Revision: 30424
2012-02-10 17:38:46 +00:00
4e332227d0
brcm47xx: update bcm5354 support patch
...
SVN-Revision: 30423
2012-02-10 17:22:26 +00:00
6c07149c2d
ar71xx: fix platform description
...
SVN-Revision: 30419
2012-02-10 15:27:49 +00:00
724211aa0d
generic: fix yaffs2 build warnings on 3.3
...
SVN-Revision: 30418
2012-02-10 15:21:43 +00:00
766999085a
ar71xx: ag71xx: add BQL support
...
It will be usable only from linux-3.3.
Based on a patch by Dave Taht <dave.taht@bufferbloat.net>
SVN-Revision: 30417
2012-02-10 14:56:47 +00:00
fc069f030b
ar71xx: add dummy DQL helper functions for 3.2
...
SVN-Revision: 30416
2012-02-10 14:56:44 +00:00
32a18a05f8
ar71xx: add preliminary support for 3.3
...
SVN-Revision: 30410
2012-02-10 11:53:56 +00:00
512df38f5c
ar71xx: disable DDR flush for ethernet on AR934x, it is no longer necessary
...
SVN-Revision: 30409
2012-02-10 11:46:37 +00:00
61f48beadd
ar71xx: fix db120 board detection
...
SVN-Revision: 30408
2012-02-10 11:46:31 +00:00
73b9a8bf9b
ar71xx: allow to build ag71xx w/o PCI support enabled
...
SVN-Revision: 30407
2012-02-10 11:46:10 +00:00
fe0c7aac66
ar71xx: merge 3.2 fixes
...
SVN-Revision: 30406
2012-02-10 08:19:33 +00:00
d72bde99cd
ar71xx: merge files-3.2 to files
...
SVN-Revision: 30405
2012-02-10 08:19:31 +00:00
81b7aaefbe
ar71xx: nuke 2.6.39 support
...
SVN-Revision: 30404
2012-02-10 08:19:28 +00:00
650d777f3d
ar71xx: switch to 3.2.5
...
SVN-Revision: 30403
2012-02-10 08:19:27 +00:00
abeab97efc
ar71xx: refresh 3.2 patches
...
SVN-Revision: 30402
2012-02-10 08:19:25 +00:00
6959317691
kernel: update linux 3.2 to 3.2.5
...
SVN-Revision: 30401
2012-02-10 08:19:23 +00:00
f754063159
ar71xx: 3.2: remove stray semicolons from the PCI fixup patch
...
SVN-Revision: 30400
2012-02-09 21:19:57 +00:00
848dedeb8b
ar71xx: fix ar934x usb reset handling on 3.2
...
SVN-Revision: 30399
2012-02-09 20:39:41 +00:00
31a0451cee
generic: fix kexec build error for MIPS with gcc-4.6-linaro
...
SVN-Revision: 30395
2012-02-09 14:06:44 +00:00
841f0f23b3
generic: 3.3: add missing config symbols
...
SVN-Revision: 30393
2012-02-09 08:07:52 +00:00
098ca08e94
generic: 3.3: fix yaffs2 build error
...
SVN-Revision: 30392
2012-02-09 08:07:50 +00:00
09c45f50d4
ar71xx: 3.2: get rid of an unused variable in ath79_spi.c
...
SVN-Revision: 30391
2012-02-08 20:47:58 +00:00
c126bed503
ar71xx: 3.2: fix AHB clock name in rb4xx_spi
...
SVN-Revision: 30390
2012-02-08 20:47:56 +00:00
32194001ed
generic: fix yaffs2 build error on 3.2
...
SVN-Revision: 30389
2012-02-08 20:47:54 +00:00
fb53d25fa4
add more missing config symbols
...
SVN-Revision: 30386
2012-02-08 17:35:40 +00:00
81f15f5026
ar71xx: add profile and build image for the TEW-673GRU board
...
SVN-Revision: 30377
2012-02-08 16:26:27 +00:00
48e85cd47b
ar71xx: add support for the TRENDNet TEW-673GRU board
...
SVN-Revision: 30376
2012-02-08 16:26:25 +00:00
b91a542247
select GENERIC_ATOMIC64 implementation to fix xfs related build errors
...
SVN-Revision: 30371
2012-02-08 10:34:21 +00:00
bd8683ac93
add audio and display features
...
SVN-Revision: 30370
2012-02-08 10:21:48 +00:00
f35c4a3266
8139cp: backport patches to make driver stable again
...
List of patches that Jo-Philipp groveled out of git.
Redux: defuzzed.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 30366
2012-02-07 21:56:51 +00:00
834be6c1fe
alix2, geos: Adjust CFLAGS
...
Clone of CFLAGS change from r30013 into Geos and Alix platforms.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 30353
2012-02-07 13:00:47 +00:00
e430c864f4
kernel: add a recent upstream commit (post-3.3) to the ssb update patch, required for the next mac80211 update
...
SVN-Revision: 30345
2012-02-07 11:28:06 +00:00
42ec97097e
generic: Enable HPET, HID and AT keyboard support
...
SVN-Revision: 30309
2012-02-05 17:56:04 +00:00
b5ff8b85d6
generic: Add missing and remove unused config symbols
...
SVN-Revision: 30133
2012-02-04 20:45:17 +00:00
778e5d4fa5
brcm63xx: add support for linux 3.3
...
SVN-Revision: 30027
2012-02-04 10:17:27 +00:00
49874a57f1
kernel: fix netfilter layer7 compilation in 3.3
...
SVN-Revision: 30026
2012-02-04 10:17:14 +00:00
d6afe712ab
x86: make alix platform patch apply to 3.3
...
Based on a patch from Philip Prindeville.
While at it, also refresh the patches.
SVN-Revision: 30025
2012-02-03 20:17:00 +00:00
c433bfb571
disable additional PATA drivers in global 3.2 and 3.3 config, remove redundant symbols from alix2 config
...
SVN-Revision: 30024
2012-02-03 19:47:55 +00:00
40867f1b68
x86: trivial -- add missing CONFIG_GEOS symbol to top-level So that builds don't stall in x86 prompting for this symbol. [From Philip Prindeville, via http://patchwork.openwrt.org/patch/1828/ ]
...
SVN-Revision: 30023
2012-02-03 19:21:41 +00:00
79a3fdb9da
geos: backport driver from linux-next to 3.2 and 3.3 The Geos driver is in linux-next and will be out in 3.4. It builds fine against 3.2.2 and 3.3-rc2. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
...
SVN-Revision: 30022
2012-02-03 18:16:27 +00:00
25d605ab0e
net5501: backport drivers from linux-next Backport net5501 platform driver from 3.4. Remove vestiges of old (pre-2.6.30) leds-net5501.c driver. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
...
SVN-Revision: 30021
2012-02-03 18:14:02 +00:00
7a36f3d2ff
x86: move additional oddball PATA drivers These should only be enabled in the generic image, as they bloat all of the other targets. Also add symbols for NET5501, ALIX, and GEOS which were added backported to 3.2 and 3.3. Restore PC speaker to Geos target. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
...
SVN-Revision: 30019
2012-02-03 18:02:57 +00:00
d13c3cd073
net5501: adjust CFLAGS and package selection ( #10893 ) This patches the CFLAGS for Geode LX CPUs for 4.3 and new GGC versions. This creates more compatible code and allowed me to boot my system first time with no troubles. Also, the missing kmod is added in.
...
SVN-Revision: 30013
2012-02-03 14:19:29 +00:00
d9ff9c44ee
ar71xx: add usb on the pb92 board
...
SVN-Revision: 30007
2012-02-03 09:44:51 +00:00
f99bf6517c
x86: add 3.3 generic symbols
...
Copy x86/config-3.2 to x86/config-3.3 and add additional symbols (for 3.3-rc2).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 30002
2012-02-02 21:01:59 +00:00
b6be49429b
alix2: backport platform driver updates from linux-next Add patches to x86/patches-3.2 and x86/patches-3.3 (update will appear in 3.4). [Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1817/ ]
...
SVN-Revision: 30001
2012-02-02 19:26:32 +00:00
7a9e4ffe8e
alix2, geos, net5501: remove kmod-ledtrig-netfilter, its not used by any standard system facility
...
SVN-Revision: 30000
2012-02-02 19:11:52 +00:00
bf8bb9b661
alix2, goes, net5501: clean up default packages Remove packages which are dependencies of other packages Remove packages which are part of the default package list Remove DSL specific packages from net5501 Remove bridge package, we use the busybox applet Replace hostapd with wpad
...
SVN-Revision: 29999
2012-02-02 19:06:22 +00:00
047ba1e12e
alix2, net5501: bump both subtargets to Linux 3.2.2 to align with the rest
...
SVN-Revision: 29998
2012-02-02 19:00:40 +00:00
1ae5715f2e
geos: add missing files from previous commit
...
SVN-Revision: 29997
2012-02-02 18:59:51 +00:00
a1258ccaba
geos: backport Geos driver from linux-next Backport of linux-next driver. Driver adds support for LEDS and S/W button. Add hotplug script for button actions. Add Openwrt system config for LEDS triggers. Add updated kernel .config for 3.2 symbols. [Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1816/ ]
...
SVN-Revision: 29996
2012-02-02 18:58:20 +00:00
415a375eaa
geos: cleanup GPIO driver name In 3.1, the old drivers/char/ entry for the CS5535 GPIO driver went obsolete. Make Geos use a recent kernel and remove this ambiguity. [Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1815/ ]
...
SVN-Revision: 29995
2012-02-02 18:44:35 +00:00
5523eca4e5
net5501: correct net5501 h/w configuration Bump to version 3.2. Simplify and correct kernel config (based on x86/config-3.2). Designate eth0 as wan interface, and bridge eth1/eth2/eth3. Add heartbeat LED trigger. Use correct CS5535 GPIO driver. Use correct USB drivers (OHCI not UHCI). Add MSR and HW clock support. Add GPIO mask definition. Add correct SATA drivers. Add LED triggers. [Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1802/ ]
...
SVN-Revision: 29994
2012-02-02 18:41:10 +00:00
eca9950f63
kernel: add preliminary support for linux 3.3
...
Based on 3.3-rc2
SVN-Revision: 29986
2012-02-02 08:23:54 +00:00
3310df6b52
alix2: correct h/w configuration Bump to version 3.2. Simplify and correct kernel config (based on x86/config-3.2). Drop obsolete CS5535 GPIO driver.
...
[Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1804/ ]
SVN-Revision: 29981
2012-02-01 15:31:23 +00:00
41bd6bd282
ar71xx: fix ethernet LEDs on the WHR-{G301N,HP-G300N,HP-GN} boards
...
SVN-Revision: 29978
2012-01-31 20:49:34 +00:00
c315ce403b
ar71xx: merge DIR-600 A1 and DIR-615 E4 support
...
SVN-Revision: 29976
2012-01-31 18:37:29 +00:00
dd47afc197
ar71xx: fix ethernet LEDs on the DIR-600-A1 board
...
SVN-Revision: 29975
2012-01-31 18:37:24 +00:00
8200f0c61a
ar71xx: unify LED names on D-Link boards
...
SVN-Revision: 29974
2012-01-31 18:37:15 +00:00
faeca86e50
ar71xx: support for D-LINK DIR-615 rev. E4
...
This patch adds support for D-LINK DIR-615 E4 board. It's mostly based
on the existing support for DIR-600 A1, with some changes in the leds
configuration.
It's an updated version of the patch that reliably works on my hw for
about a year (it was built from trunk on Jan 2011). When I decided to
update the firmware and checked for the current support for that device,
I also found previously posted patches by Alexey Loukianov that
mentioned some stability issues. I'm not sure where could be the
difference, the patches are very similar except the wmac led pin number
- I was using 1, and those patches used 17.
[juhosg: add 3.2 support]
Signed-off-by: Vadim Girlin <vadimgirlin@gmail.com>
SVN-Revision: 29973
2012-01-31 18:37:09 +00:00
97e4ddd012
ar71xx: add support for TP-Link TL-MR11U
...
Adds support for TL-MR11U, a portable router with very similar
hardware to the TL-WR703N and TL-MR3020, but with an onboard
2000mAh battery.
Tested, working:
All interfaces (Ethernet, 802.11n, USB)
WPS & Reset switches (Power appears to be a hardware slider)
Ethernet, Wifi, 3G LEDs (Power & charging LEDs hardware controlled)
Sysupgrade
[juhosg: fix indentations to use TABs instead of spaces, fix 3.2 patch
breakage]
Signed-off-by: Simon Taylor <simon.taylor.uk@gmail.com>
SVN-Revision: 29972
2012-01-31 18:37:01 +00:00
8766f32b8c
ar71xx: compress kernel binaries in Image/Prepare stage
...
The lzma compressed kernel is used by one of the loaders.
SVN-Revision: 29971
2012-01-31 18:36:54 +00:00
d5d37febb4
ar71xx: use dynamically allocated partitions in wrt160nl_part
...
SVN-Revision: 29970
2012-01-31 18:36:51 +00:00
44ed690cb3
ramips: change vlan_config for the ALFA W502U board
...
This change moves the WAN port into a separate VLAN.
SVN-Revision: 29969
2012-01-31 18:34:10 +00:00
b3568b10c2
kernel: update linux 3.2 to 3.2.2
...
SVN-Revision: 29967
2012-01-31 09:44:00 +00:00
1015fab0d7
kernel: update linux 3.1 to 3.1.10
...
SVN-Revision: 29966
2012-01-31 09:43:57 +00:00
e67f4477bb
kernel: update linux 3.0 to 3.0.18
...
SVN-Revision: 29965
2012-01-31 09:43:53 +00:00
882eddbf92
build 96348R images
...
SVN-Revision: 29960
2012-01-30 21:12:32 +00:00
0700644b16
remove support for 2.6.39
...
SVN-Revision: 29959
2012-01-30 21:12:28 +00:00
038fc8eac3
bump to 3.0.17
...
SVN-Revision: 29958
2012-01-30 21:12:25 +00:00
8100658a30
add missing config symbols
...
Thanks KanjiMonster
SVN-Revision: 29955
2012-01-30 10:53:20 +00:00
0501ea063b
fix gpiommc build failure with 3.2
...
SVN-Revision: 29954
2012-01-30 10:53:16 +00:00
55b5e15bff
create a config-3.2 for upcoming changes, rebase config-default to 2.6.39
...
SVN-Revision: 29953
2012-01-30 02:13:37 +00:00
8c4813b75e
add default and Sim.One profiles
...
SVN-Revision: 29942
2012-01-29 15:00:36 +00:00
0bb50678de
add 3.2 support
...
SVN-Revision: 29941
2012-01-29 15:00:33 +00:00
e82f06639e
add another 3.2 framebuffer symbol
...
SVN-Revision: 29940
2012-01-29 15:00:29 +00:00
ad808cf7e6
add support for 3.2 kernel
...
SVN-Revision: 29939
2012-01-29 15:00:25 +00:00
eeb00634a7
add support for the Atheros AP113 reference board
...
This reference board is equipped with:
- AR7242 SoC
- AR9580 on-board Wi-Fi
- AR8316 switch
SVN-Revision: 29935
2012-01-28 13:19:49 +00:00
405a0f3905
refresh 3.2 patches
...
SVN-Revision: 29934
2012-01-28 13:19:43 +00:00
d1c07b3657
brcm47xx: add fix for cardbus host controller
...
These devices have two devices on the bus, the host controller itself and the device.
SVN-Revision: 29923
2012-01-27 20:10:51 +00:00
b9b768b8d3
ar71xx: use 64k block size for WZR-HP-AG300H
...
SVN-Revision: 29917
2012-01-27 10:42:41 +00:00
ac8116739a
ar71xx: fix sysupgrade image building of atheros boards after r29899
...
SVN-Revision: 29916
2012-01-27 07:51:09 +00:00
013fe76b36
ar71xx: create the temporary directory before building initramfs images
...
Thanks to Florian for reporting.
SVN-Revision: 29915
2012-01-26 21:28:34 +00:00
a5538a18d4
ar71xx: create a profile and build images for Compex WPE72
...
[juhosg: remove ath9k from the the profile package list, build WPE72
image with the Default profile as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 29914
2012-01-26 17:01:44 +00:00
e1e84badaa
ar71xx: add support for Compex WPE72/WPE72NX
...
This patch adds support for Compex WPE72 bare board and Compex WPE72NX
Indoor Access Point.
[juhosg: add support to 3.2 as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 29912
2012-01-26 17:01:41 +00:00
1c4f6b4308
generic: add WPE72 ID to myloader.h
...
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 29911
2012-01-26 17:01:38 +00:00
b3fdd931d1
ramips: add support for Sitecom WL-341v3 and other Sercomm IP1006RRv2 boards
...
This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 29910
2012-01-26 10:44:23 +00:00
038d4e0d77
ar71xx: TL-MR3020: fix board detection, fix missing mandatory package and modify LED behaviour
...
This patch fixes the board detection of the TL-MR3020.
The LED behaviour has also been modified:
* The WPS LED is the diag LED now.
* A netdev trigger for the LAN LED has been added.
The profile of the TL-MR3020 has been updated because the needed package
"kmod-ledtrig-usbdev" was missing which resulted in a non-working usbdev
trigger for the 3G/USB LED.
[juhosg: the board name changes has been removed, and the kernel files
has been changed instead.]
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29905
2012-01-25 07:44:45 +00:00
c11ac55b29
ar71xx: TL-MR3020: fix GPIO polarity for button and switch
...
This patch fixes the GPIO polarity for the button and the sliding
switch. The buttons are not active low. "Pressed" and "Released"
events are wrong without the patch.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29904
2012-01-25 07:44:43 +00:00
4f3d6c9ae9
ar71xx: use the lzma loader on the Planex boards
...
SVN-Revision: 29900
2012-01-24 20:12:10 +00:00
5fa9768cee
ar71xx: rename Sysupgrade/{KR,RK} to Sysupgrade/{KR,RK}uImage
...
SVN-Revision: 29899
2012-01-24 20:12:08 +00:00
095c236694
ar71xx: fix the AP/Router LED definitons on MZK-W300NH
...
SVN-Revision: 29897
2012-01-24 18:40:38 +00:00
23e1b451dc
ar71xx: preset WLAN LED config on MZK-W300NH
...
SVN-Revision: 29896
2012-01-24 18:40:36 +00:00
23836d5908
ar71xx: remove hardcoded MTD layout from planex files
...
SVN-Revision: 29895
2012-01-24 18:40:34 +00:00
859c915077
ar71xx: pass mtdlayout to Planex boards via command line
...
SVN-Revision: 29894
2012-01-24 18:40:33 +00:00
6ad9bf8d17
ar71xx: remove an unused header file
...
SVN-Revision: 29893
2012-01-24 18:40:31 +00:00
02e77c6ae1
ramips: generate sysupgrade image for the ALL0256N
...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29884
2012-01-24 11:48:48 +00:00
944c8aacdb
ramips: add user-space support for ALL0256N
...
This adds uci-defaults and sysupgrade support for the ALL0256N.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29883
2012-01-24 11:48:47 +00:00
1932a7205c
ramips: add kernel support for ALL0256N
...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29882
2012-01-24 11:48:45 +00:00
17bb003891
ar71xx: nuke fs_all variable in image/Makefile
...
SVN-Revision: 29880
2012-01-24 09:47:25 +00:00
1fb88e2541
ar71xx: create interim kernel files in a separate dir
...
This reduces the size of the ImageBuilder tarball a lot.
SVN-Revision: 29879
2012-01-24 09:47:23 +00:00
a43e2f508f
ar71xx: prebuild all loaders in Image/Prepare stage
...
SVN-Revision: 29878
2012-01-24 09:47:22 +00:00
9cf1d4e06e
ramips: scripts updates
...
In this patch:
* rename Argus leds to avoid underscores
* rename Belkin F5D8235 v1 leds from f5d8234 to f5d8235
* remove Belkin F5D8235 v1 status led defined as storage led (it was
defined as usb led earlier, just in wrong place) - it should have
router led as in v2
* add Argus, Sparklan and Belkin F5D8235 v2 status leds
* add Belkin F5D8235 v1 and v2 usb leds
* fix Belkin F5D8235 v2 network config generation and mac address axtraction
* fix Sparklan board identification
* add Sparklan usb led (this board doesn't have usb connector by
default and the led is hidden also but if you are going to solder
the connector then you'll see the led too)
* add Sparklan network config generation and mac address extraction
* fix empty string test in network script and...
* ...sort case entries by the first board in the list
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29871
2012-01-23 10:23:32 +00:00
44517a3789
ar71xx: 3.2: fix build errors if PCI is not enabled
...
SVN-Revision: 29870
2012-01-23 08:52:21 +00:00
778db0a13d
ar71xx: fix compiler warning if PCI is not enabled
...
SVN-Revision: 29869
2012-01-23 08:52:18 +00:00
af015f956c
ar71xx: add initial support for 3.2
...
Tested on the following boards:
ALFA AP96
TL-MR3220 v1
TL-WR1043ND v1
TL-WR2543ND v1
TL-WR703N v1
TL-WR741ND v1
TL-WR741ND v4
WNDR3700 v1
WZR-HP-G300NH
SVN-Revision: 29868
2012-01-22 22:38:19 +00:00
386cbfe45b
ar71xx: move arch specific files to files-2.6.39
...
SVN-Revision: 29867
2012-01-22 22:38:11 +00:00
7b7427e52c
ar71xx: build ALFA AP96 images with default profile as well
...
SVN-Revision: 29866
2012-01-22 22:33:15 +00:00
dd49cca9d6
generic: 3.2: allow to build myloader mtd parser for ATH79
...
SVN-Revision: 29860
2012-01-22 18:43:39 +00:00
9be1b91644
generic: allow to build myloader mtd parser for 3.2+
...
SVN-Revision: 29858
2012-01-22 18:36:49 +00:00
809fe38e41
ramips fix f5d8235-v1 diag LED support
...
SVN-Revision: 29857
2012-01-22 18:11:39 +00:00
e7dee3aeed
ar71xx: wrt160nl_part: include module.h and fix compiler warnings
...
SVN-Revision: 29856
2012-01-22 17:55:38 +00:00
a7d344565b
ar71xx: tplinkpart: include module.h
...
SVN-Revision: 29855
2012-01-22 17:55:36 +00:00
6c2638c5e2
ar71xx: rename vsc7385 spi driver
...
SVN-Revision: 29853
2012-01-22 13:51:57 +00:00
bb16739db9
ar71xx: rename ap81 spi driver
...
SVN-Revision: 29852
2012-01-22 13:51:56 +00:00
5ef8b922fa
ar71xx: rename rb4xx spi drivers
...
SVN-Revision: 29851
2012-01-22 13:51:54 +00:00
aad175d5b6
ar71xx: rename the nxp_74hc153 driver
...
SVN-Revision: 29850
2012-01-22 13:51:52 +00:00
ef1c53b7b7
ar71xx: change board id of the UniFi board
...
SVN-Revision: 29849
2012-01-22 13:51:50 +00:00
f90e578903
ar71xx: include linux/module.h in the micrel phy driver
...
SVN-Revision: 29848
2012-01-22 13:51:49 +00:00
e9d8deaaed
ramips: add sysled and sysupgrade to wr512-3gn
...
Patch from #10035 .
SVN-Revision: 29847
2012-01-22 13:43:23 +00:00
8e662f28fe
generic: 3.2: don't disable lockdep for OOT modules
...
SVN-Revision: 29846
2012-01-22 09:57:39 +00:00
4625c9b5a4
generic: rtl8366: add rtl8366_smi_write_reg_noack helper
...
After issuing a soft reset on the RT8366{S,RB}
switch, waiting for the last acknowlegement fails
in rtl8366_smi_write_reg. Add a _noack version of
the function and use that for issuing a soft reset.
SVN-Revision: 29844
2012-01-21 22:44:09 +00:00
26d4e1876c
brcm47xx: add support for pcie host controller on bcma based SoCs.
...
This also adds minimal support for the BCMA43224 pcie wireless card.
SVN-Revision: 29843
2012-01-21 22:39:20 +00:00
557cf076b4
ramips: sysupgrade for ESR-9753
...
This patch add sysupgrade for Engenius ESR-9753
Signed-off-by: Artur Wronowski <arteqw@gmail.com>
SVN-Revision: 29824
2012-01-20 10:49:26 +00:00
aa8f9171f2
kernel: fix OCF for linux 3.2
...
Add skb_frag_page from 3.2 to OCF for 3.1 and earlier and use it.
SVN-Revision: 29818
2012-01-19 19:51:54 +00:00
fc512193a0
add missing kernel symbols
...
SVN-Revision: 29790
2012-01-19 01:57:22 +00:00
2fc3fe1d09
Make the grub timeout configurable on x86 targets
...
Signed-off-by: Justus Winter <4winter@informatik.uni-hamburg.de>
SVN-Revision: 29786
2012-01-19 01:14:45 +00:00
095f7f2da3
x86/config-3.2: add linux-3.2 symbols for x86
...
The following symbols are missing for x86, in sorted order.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 29783
2012-01-19 00:31:39 +00:00
dbfeb5d158
fix thinko in 102-ehci_hcd_ignore_oc patch
...
SVN-Revision: 29773
2012-01-18 07:56:02 +00:00
49eb3fd845
gigaset 76x
...
* fixes leds
* adds all leds found on the sx763 board
* removes board_config from flash layout because wireless data is stored in kernel (ath5k)
* fix button handling
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 29763
2012-01-17 12:10:35 +00:00
a2708d11e8
ramips: Rework ramips_eth to not require irqsave locking anymore
...
Previously the tx housekeeping was done in a spin_lock_irqsave critical
section which causes irqs to be disabled during that time. Since the
housekeeping is already prepared to be scheduled as a tasklet process
the housekeeping only in softirq context and revise the locking between
the tx path and the housekeeping tasklet by using a normal spin_lock
which in most situations will be a NOP anyway.
This makes sure that interrupts are only disabled for a short time
since in the worst case the housekeeping might have to free up to 256
skbs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 29762
2012-01-17 11:23:11 +00:00
034cf5643f
brcm47xx: add support for kernel 3.2
...
SVN-Revision: 29756
2012-01-15 21:18:34 +00:00
c3d134af12
brcm47xx: run kernel_oldconfig
...
SVN-Revision: 29755
2012-01-15 14:53:32 +00:00
f9e41adc80
add support for OMAP4 based boards, starting with the PandaBoard
...
SVN-Revision: 29753
2012-01-14 23:02:56 +00:00
6274648199
fixup arm xz support with recent changes
...
SVN-Revision: 29750
2012-01-14 22:55:04 +00:00
e65195c246
add missing symbols
...
SVN-Revision: 29749
2012-01-14 22:53:28 +00:00
b0479e2ca2
kernel: disable bridge igmp snooping in 3.2 as well
...
SVN-Revision: 29747
2012-01-14 14:57:03 +00:00
66895b7115
kernel: disable bridge igmp snooping by default to avoid multicast issues
...
SVN-Revision: 29744
2012-01-14 13:50:25 +00:00
9eb73ee6b7
kernel: ppc40x: ppc44x: add missing kernel config symbol
...
SVN-Revision: 29742
2012-01-14 12:04:17 +00:00
d5bc3a994b
brcm47xx: update usb driver
...
Add workarround for BCM5357 and BCM4749.
This patch contains the following fixes from George Kashperko:
* separate subroutines for controller initialization workarounds -
following CodingStyle recommendations;
* __devinit __devexit __devinitconst annotations for CONFIG_HOTPLUG;
* fix leak in ssb_hcd_create_pdev/bcma_hcd_create_pdev - as hci_res being
kmalloc'ed is never freed anywhere while platform_device_add_resources
will kmemdup resources right away;
* fix compilation error in ssb_hcd_resume - it will fail as soon as
CONFIG_PM is selected.
SVN-Revision: 29734
2012-01-13 20:11:23 +00:00
9d497cb132
rtl8366: fix rtl8366_smi_detect() after r29677
...
SVN-Revision: 29732
2012-01-13 19:17:58 +00:00
3883e71097
brcm63xx: add support for linux 3.2
...
SVN-Revision: 29731
2012-01-13 14:59:50 +00:00
1bc0abb058
kernel: add support for linux 3.2.1
...
SVN-Revision: 29730
2012-01-13 14:55:07 +00:00
f3f1075655
kernel: backport overlayfs v11 to 3.0 and 2.6.39
...
Should fix whiteout issues and missing files when using extroot.
SVN-Revision: 29727
2012-01-13 14:42:53 +00:00
c560444a58
kernel: update linux 3.1 to 3.1.9
...
SVN-Revision: 29726
2012-01-13 14:38:28 +00:00
e49d3e1d5b
kernel: update linux 3.0 to 3.0.17
...
SVN-Revision: 29725
2012-01-13 14:10:44 +00:00
e87bb77966
ar8216: use vlan configuration for connecting ports (forced to be untagged) even with vlan_enable=0, but keep them isolated before the switch has been configured this makes enable_vlan=0 practical for vlan passthrough
...
SVN-Revision: 29719
2012-01-12 10:15:11 +00:00
c33e016fa5
ar8216: do not strip vlan tags when running with vlan_enable=0
...
SVN-Revision: 29718
2012-01-12 10:15:08 +00:00
fbf81c8e79
ar71xx: move irq_to_gpio and gpio_to_irq into gpio.c
...
SVN-Revision: 29713
2012-01-11 18:00:50 +00:00
034b7f0ef5
Remove invalid LED GPIO from GW6200 board definition. GPIO 35 isn't intended to control ethernet LED (the led behaviour is a side effect) and using the gpio as an led causes kernel panics.
...
SVN-Revision: 29712
2012-01-11 13:47:48 +00:00
67f62cf5cf
ar71xx: disable ath79 in order to get rid of Kconfig warnings
...
SVN-Revision: 29711
2012-01-11 09:14:19 +00:00
88d8cdd503
ar71xx: pb44_spi: add shutdown handler
...
This allows to access the flash from a kexec'd kernel.
SVN-Revision: 29710
2012-01-11 09:14:18 +00:00
e1b7995aef
ar71xx: pb44_spi: call pb44_spi_{en,dis}able from probe/remove
...
SVN-Revision: 29709
2012-01-11 09:14:17 +00:00
67444c7795
ar71xx: pb44_spi: introduce pb44_spi_{en,dis}able helpers
...
SVN-Revision: 29708
2012-01-11 09:14:15 +00:00
0f566a376c
ar71xx: ar71xx_spi: add shutdown handler
...
This allows to access the flash from a kexec'd kernel.
SVN-Revision: 29707
2012-01-11 09:14:14 +00:00
09a6e3f662
ar71xx: ar71xx_spi: save and restore regs from probe/remove
...
SVN-Revision: 29706
2012-01-11 09:14:13 +00:00
714a9bd641
ar71xx: ar71xx_wdt: add shutdown handler
...
SVN-Revision: 29705
2012-01-11 09:14:11 +00:00
9727256330
ar71xx: refresh patches
...
SVN-Revision: 29683
2012-01-07 19:36:43 +00:00
4edff7d3ef
ar71xx: add a profile and build images for the TL-WR2543N/ND
...
SVN-Revision: 29682
2012-01-07 19:36:42 +00:00
a1dcbc66a6
ar71xx: add initial support for the TL-WR2543N/ND board
...
The WLAN LEDs are not working yet.
SVN-Revision: 29680
2012-01-07 19:36:35 +00:00
a56bdeff9d
ar71xx: allow to specify max read size for m25p80
...
Reading from the flash chip on the TL-WR2543ND seems buggy.
If the SPI flash driver tries to read too much data in one
SPI transfer, the flash chip returns bogus values. This can
be caused by a buggy flash chip on my board, or it can
be a bug in our SPI driver.
Add a workaround to the m25p80 driver until I find out the
root cause of the problem. The patch allows to specify the
maximum numner of bytes which can be read safely withint
one SPI transfer.
SVN-Revision: 29679
2012-01-07 19:36:33 +00:00
8b567fb508
generic: add driver for the RTL8367R/M switches
...
SVN-Revision: 29678
2012-01-07 19:36:31 +00:00
87fb92ee03
generic: rtl8366: preparing for RTL8367 support
...
* make clock delay configurable
* make read,write commands configurable
* use u16 for member and untag fields
SVN-Revision: 29677
2012-01-07 19:36:30 +00:00
43196813d7
generic: rtl8366_smi: add timeout message
...
SVN-Revision: 29676
2012-01-07 19:36:25 +00:00
67b2814842
ar71xx: local mac support on the wndr3700
...
The wndr3700 at least has no eth0 mac address and usually leverages
the first wireless device's mac when in a bridged scenario. If,
however, you want to route, and not bridge the interfaces, you
need a unique mac address for it.
This patch sets the local bit on the mac address pulled from the
wireless chip and uses the resulting address for eth0.
Patch-by: Dave Taht <dave.taht@gmail.com>
SVN-Revision: 29675
2012-01-07 17:24:44 +00:00
6c74274c8d
generic: improve MIPS kexec support
...
It is based on patches from the linux-longsoon-community git tree:
http://dev.lemote.com/cgit/linux-loongson-community.git/
Now the kernel can use the command line parameter from kexec-tools.
Runtime tested on ar71xx with 2.6.39.4 (the wathdog must be stopped
before executing the new kernel). Compile tested with lantiq (3.1.4)
and brcm47xx (3.0.12).
SVN-Revision: 29674
2012-01-07 16:29:16 +00:00
f638c6207b
ar71xx: fix sysupgrade on the TL-WR841N/ND v7 boards
...
SVN-Revision: 29672
2012-01-06 15:54:59 +00:00
1e848b17ad
ar71xx: add support for Redwave RW2458N
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 29669
2012-01-06 07:20:59 +00:00
84cd8a5ee0
ar71xx: fix RB-750 network configuration
...
SVN-Revision: 29668
2012-01-06 07:20:54 +00:00
8eb0b7ab3d
ar71xx: fix sections mismatch warnings in the nand drivers
...
SVN-Revision: 29667
2012-01-05 18:08:33 +00:00
232eb83f74
ar71xx: fix LED configuration on the RB-750
...
SVN-Revision: 29666
2012-01-05 18:08:28 +00:00
d65c6fe720
ar71xx: create profile and build image for the ALFA AP96 board
...
SVN-Revision: 29663
2012-01-04 21:13:57 +00:00
b8f0d86115
ar71xx: add inital support for the ALFA Network AP96 board
...
The microSD slot and the Real Time Clock is not working yet.
The miniPCIe interface is not tested due to the lack of a
suitable card.
SVN-Revision: 29662
2012-01-04 21:13:54 +00:00
807e046193
ar71xx: specify console kernel parameter for the Compex boards
...
SVN-Revision: 29660
2012-01-04 17:30:59 +00:00
923f3e3752
ar71xx: allow to use the command line hack on compex devices
...
SVN-Revision: 29659
2012-01-04 17:30:58 +00:00
2f53f82203
ar71xx: use the TL-MR3x20 code for the TL-WR841N/ND v7
...
These models are based on the AP99 reference board,
and uses the AR7241 SoC.
SVN-Revision: 29658
2012-01-04 17:30:57 +00:00
301b1b4f92
ar71xx: show correct model name on TL-WA701N/ND boards
...
SVN-Revision: 29657
2012-01-04 17:30:55 +00:00
ac68f0d8fa
ar71xx: add profile and build image for the TL-WA701N/ND boards
...
SVN-Revision: 29656
2012-01-04 17:30:54 +00:00
72019009c7
ar71xx: fix network configuration for the TL-WA901N/ND boards
...
SVN-Revision: 29654
2012-01-04 17:30:52 +00:00
90bfef9ec9
ar71xx: allow to use LAN LED on the TL-WA901N/ND boards
...
SVN-Revision: 29653
2012-01-04 17:30:50 +00:00
5eb502d9c1
ar71xx: add default LED configuration for the TL-MR3020
...
Also use the system LED for diagnostic.
SVN-Revision: 29652
2012-01-04 17:30:49 +00:00
1045c83527
ar71xx: add support for TP-Link TL-MR3020
...
This patch adds support for the TP-Link device TL-MR3020 which is very
similiar to the TL-WR703N.
The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions.
Only four LEDs can be controlled via GPIO. The power LED is connected to
the power supply.
The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals
of the sliding switch have been mapped to BTN_0 and BTN_1.
I have also setup a wiki page with details here:
http://wiki.openwrt.org/toh/tp-link/tl-mr3020
USB is working and has been tested with USB mass storage and USB UMTS
stick.
Wifi also seems to work.
Ethernet is working too.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29651
2012-01-04 17:30:47 +00:00
88223f87d1
ar71xx: use the new om-watchdog package for OM2P
...
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
SVN-Revision: 29648
2012-01-04 17:30:41 +00:00
a788f199c9
remove current RTSP support
...
SVN-Revision: 29643
2012-01-04 00:29:29 +00:00
237282ae8c
backport upstream commit e1738bd9cecc5c867b0e2996470c1ff20f66ba79 to affected kernels ( #9802 ) commit 8efa88540635 (sch_sfq: avoid giving spurious NET_XMIT_CN signals) forgot to call qdisc_tree_decrease_qlen() to signal upper levels that a packet (from another flow) was dropped, leading to various problems.
...
SVN-Revision: 29642
2012-01-03 23:08:15 +00:00
8854c90119
ar71xx: add profile and build factory image for the Hornet-UB board
...
SVN-Revision: 29637
2012-01-01 19:30:29 +00:00
1d3de89f3c
ar71xx: build images for the ALFA Network N2/N5 boards
...
SVN-Revision: 29636
2012-01-01 19:30:28 +00:00
1e68f10b87
ar71xx: add support for the ALFA Network N2/N5 boards
...
SVN-Revision: 29635
2012-01-01 19:30:25 +00:00
5c067db8a7
ar71xx: define LAN/WAN LEDs for the TL-WR741N/ND boards
...
SVN-Revision: 29631
2011-12-31 15:02:46 +00:00
fff02e6ea8
ar71xx: enable SWCONFIG_LEDS
...
SVN-Revision: 29630
2011-12-31 15:02:40 +00:00
5fa65cba6e
kernel: swconfig: introduce a generic switch LED trigger
...
SVN-Revision: 29627
2011-12-31 15:02:30 +00:00
8c2482f76e
ar71xx: ag71xx: implement get_port_{link,stats} callbacks
...
SVN-Revision: 29626
2011-12-31 15:02:26 +00:00
975355a2b1
kernel: swconfig: add get_port_{link,stats} callbacks
...
SVN-Revision: 29625
2011-12-31 15:02:24 +00:00
557009bbdb
ar71xx: fix LEDs on the WRT400N
...
SVN-Revision: 29624
2011-12-31 13:54:11 +00:00
244c322d25
ramips: rt288x: add support for the Belkin F5D8235-4 v1 board
...
Patch-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 29617
2011-12-28 08:43:43 +00:00
f50b02b559
ramips: rt288x: change base address and window size of flash bank 0
...
SVN-Revision: 29616
2011-12-28 08:43:36 +00:00
98437278c4
ramips: rt305x: add support for the ALFA Networks W502U (R36) board
...
SVN-Revision: 29615
2011-12-28 08:43:32 +00:00
76dacee995
ar71xx: enable sysupgrade support for airrouter
...
Works for me! ;-)
Patch-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 29614
2011-12-27 16:59:43 +00:00
c6ee919b2a
ar71xx: fix sysupgrade on PB42/PB44 boards
...
SVN-Revision: 29613
2011-12-27 16:57:01 +00:00
723d8dd74f
ramips: rt288x: add support for the Buffalo WLI-TX4-AG300N board
...
SVN-Revision: 29612
2011-12-27 16:56:30 +00:00
9fa33ceee2
add missing config symbol
...
SVN-Revision: 29610
2011-12-25 13:33:18 +00:00
11125d68ed
brcm47xx: fix usb on more recent bcma based devices.
...
SVN-Revision: 29605
2011-12-23 17:21:52 +00:00
7b1e525b56
ramips: initial support for Sitecom WL-351 v1 002
...
This add support for the Sitecom WL-351 v1 002.
In principle the Engenius ESR9850 should also work with this, but I
don't have the hardware to test it.
Since an external gigabit switch (RTL8366RB) is used,
I had to modify the ramips_esw driver to add a 'bypass' mode, which
just configures it to not filter the vlan tags.
Also two initialization words (FCT2 and FPA2) are set to different
values by u-boot than what the driver is using and it only seems to
work correctly when they not overridden by the driver, so I
added them to the platform specific data as reg_initval_fct2 and
reg_initval_fpa2.
With this wired lan works as expected, however I'm still having some
trouble with the wireless lan:
It only works after I rmmod & re-insmod rt2800pci and then
reconfigure it in the webinterface, but not directly after
rebooting.
The symptom of this is wpad saying:
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: associated (aid 1)
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> WPA: pairwise key handshake completed (RSN)
Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: authenticated
But wpa_supplicant on the client saying:
Authentication with <wl351mac> timed out.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 29604
2011-12-23 14:27:16 +00:00
2cb946f5b4
ramips: add support for the Senao/EnGenius ESR-9753 board
...
Signed-off-by: Artur Wronowski <arteqw@gmail.com>
SVN-Revision: 29603
2011-12-23 14:27:10 +00:00
03bce34384
ramips: define firmware partition for Omnima MiniEMBWiFi
...
Patch-by: Ivan Ignjatic <ivan@omnima.co.uk>
SVN-Revision: 29602
2011-12-23 14:27:05 +00:00
db0a1db257
ar71xx: set a reserved bit that resets to 1 when writing the address table control register on the ar7240 switch (should fix #10547 )
...
SVN-Revision: 29598
2011-12-22 05:43:53 +00:00
8799627ef0
ar71xx: add default network config for buffalo WZR-HP-G300NH2 and WZR-HP-G450H
...
Thanks netprince for reporting and testing.
SVN-Revision: 29595
2011-12-21 19:32:40 +00:00
ebefe1eb3a
the mach file of the WZR-HP-G300NH2 accidentally claimed the mach id of the WZR-HP-AG300H, correct the id ( #10649 )
...
SVN-Revision: 29593
2011-12-21 01:27:48 +00:00
0cd03df3b1
brcm47xx: remove patch starting adding brcm4716 to ssb
...
brcm4716 is supported by bcma now we do not need this patch
SVN-Revision: 29576
2011-12-19 23:55:20 +00:00
5b8686c303
brcm47xx: add new usb driver for bcma bus and replace ssb usb driver.
...
This new usb driver uses an extra device so the ehci and the ohci driver are not depending on ech other any more.
SVN-Revision: 29575
2011-12-19 23:39:13 +00:00
1aa5a61754
kernel: update bcma and ssb to version master-2011-12-16 from wireless-testing
...
SVN-Revision: 29574
2011-12-19 23:33:03 +00:00
91d0ef6f19
brcm47xx: remove support for kernel 2.6.39
...
There are problems with the patches for kernel 2.6.39 and I do not want to support two different sets of patches.
SVN-Revision: 29573
2011-12-19 23:26:15 +00:00
11013ad947
ar71xx: add missing wireless led changes for wzr-hp-g300nh2
...
SVN-Revision: 29568
2011-12-19 09:04:15 +00:00
0cc056cb7e
ar71xx: add support for the wzr-hp-g300nh2
...
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
SVN-Revision: 29567
2011-12-18 22:20:17 +00:00
5a0a2b2f1b
ar71xx: use 64kraw template on more TP-Link boards
...
SVN-Revision: 29561
2011-12-17 18:49:55 +00:00
67c7980290
ar71xx: connect GMAC0 to the internal switch on DB120
...
Because the external switch has no driver yet, connect GMAC0
to the PHY4 of the internal switch for now. This allows to
use the DB120 board as a router with 4LAN+1WAN ports.
SVN-Revision: 29557
2011-12-15 22:25:38 +00:00
5bbd416e38
ar71xx: add defines for the AR934X GMAC interface
...
SVN-Revision: 29556
2011-12-15 22:25:36 +00:00
e47a8c2bb2
ar71xx: fix GMAC1 interface speed on the DB120 board
...
SVN-Revision: 29555
2011-12-15 22:25:35 +00:00
36bc2c2c80
ar71xx: ag71xx: fix switch port setup for AR934X
...
SVN-Revision: 29554
2011-12-15 22:25:32 +00:00
00667c3846
ar71xx: ag71xx: allow to connect PHY4 to the CPU on AR934X
...
SVN-Revision: 29553
2011-12-15 22:25:30 +00:00
0540970345
ar71xx: ag71xx: setup switch interface mode on AR934X
...
SVN-Revision: 29552
2011-12-15 22:25:29 +00:00
44014110b8
ar71xx: ag71xx: detect the built-in switch of the AR934X SoCs
...
SVN-Revision: 29551
2011-12-15 22:25:28 +00:00
e2a546d475
ar71xx: allow to attach the internal switch for AR934x
...
SVN-Revision: 29550
2011-12-15 22:25:22 +00:00
9ae65588d8
ar71xx: introduce ar71xx_switch_data
...
SVN-Revision: 29549
2011-12-15 22:25:11 +00:00
bfe747b7d9
ar71xx: build images for TL-WR741N/ND v2
...
SVN-Revision: 29548
2011-12-15 22:03:48 +00:00
aefff26624
ar71x: use raw squashfs images for TP-Link boards
...
SVN-Revision: 29547
2011-12-15 22:03:46 +00:00
d5bd28ffae
ar71xx: create a template for using unpadded squashfs images
...
SVN-Revision: 29546
2011-12-15 22:03:45 +00:00
dbc4fa4b5b
ar71xx: put squash image right after the kernel on TP-Link boards
...
SVN-Revision: 29545
2011-12-15 22:03:44 +00:00
850be54b72
ar71xx: tplinkpart: allow to detect JFFS2 as well
...
SVN-Revision: 29543
2011-12-15 22:03:40 +00:00
b7d7481b07
ar71xx: ag71xx: check PHY IDs before accessing the switch registers
...
SVN-Revision: 29541
2011-12-15 13:25:23 +00:00
0655552860
ar71xx: ag71xx: don't use port 4 of the switch, it is not connected on ar724x
...
SVN-Revision: 29540
2011-12-15 13:25:21 +00:00
204fc6bed5
ar71xx: ag71xx: nuke ar7240sw_init
...
SVN-Revision: 29539
2011-12-15 13:25:20 +00:00
d1f7783612
ar71xx: fix mac addresses on jjPlus devices
...
SVN-Revision: 29538
2011-12-15 13:25:18 +00:00
d3058b8f8c
ar71xx: build image for the Hornet-UB board
...
SVN-Revision: 29536
2011-12-14 20:54:11 +00:00
b9c5cb5c9a
ar71xx: add support for ALFA Network's Hornet-UB board
...
SVN-Revision: 29535
2011-12-14 20:54:10 +00:00
66c8cc0f6d
ar71xx: add GPIO function bit defines for AR933X
...
SVN-Revision: 29534
2011-12-14 20:54:07 +00:00
0c38d36488
ramips: add support for Omnima MiniEMBWiFi board
...
This patch adds support for the Omnima MiniEMBWiFi
Ralink RT3050F based board.
Based on a patch by Ivan Ignjatic <ivan at omnima.co.uk>
SVN-Revision: 29533
2011-12-14 20:51:26 +00:00
7076d74b21
ar71xx: fix gpio count for ar7241/ar7242
...
SVN-Revision: 29532
2011-12-14 20:47:24 +00:00
b878f4a927
ar71xx: register extra leds behind the wireless mac on wzr-hp-g450h
...
SVN-Revision: 29531
2011-12-14 20:21:42 +00:00
e3017bc05e
ath9k: add support for registering extra leds connected to the wmac gpio lines
...
SVN-Revision: 29530
2011-12-14 20:21:36 +00:00
d2717d3d47
ar71xx: get rid of squashfs-4k images
...
SVN-Revision: 29522
2011-12-13 20:41:24 +00:00
5afedc67e2
generic: disable 'small sector' erase in m25p80 driver
...
This fixes the issues with the jffs2 images on various boards. Using
JFFS2 on devices with 4KiB erase sectors is not safe:
http://lists.infradead.org/pipermail/linux-mtd/2011-June/036591.html
SVN-Revision: 29521
2011-12-13 20:41:22 +00:00
4a441570ca
kernel: move linux/ath9k_platform.h to generic files so that it can be reused from other targets
...
SVN-Revision: 29516
2011-12-13 15:14:59 +00:00
3806671fe5
ar71xx: fix wireless led on wzr-hp-g450h
...
SVN-Revision: 29515
2011-12-13 15:00:43 +00:00
2dd7dfb1c9
ar71xx: enable AR9341 support at setup.c
...
Patch-by: dyq <729650915@qq.com>
SVN-Revision: 29514
2011-12-13 14:59:43 +00:00
058998acdb
ar71xx: Build images for Netgear WNDRMAC and WNDRMACv2
...
The WNDRMAC is a WNDR3700v2 (64MB RAM, 16MB flash) in a white case. The
WNDRMACv2 is a WNDR3800 (128MB RAM, 16MB flash) in a WNDRMAC case.
The WNDRMAC case doesn't have "holes" or labels for the 2.4GHz LED or
switch ports 2-4. The stock firmware uses a single LED (in the 5GHz
position) to indicate the status of both radios, and a single LED (in the
switch port 1 position) to indicate the status of all LAN ports. The
"missing" LEDs are present on the board, and easily shine through the
case. Unlike the stock firmware, OpenWrt will use these "hidden" LEDs.
I've tested the WNDRMACv2 image. I don't have a v1 WNDRMAC, but assume
that this is sufficient to build a fully-functional image.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29513
2011-12-13 14:59:40 +00:00
48f9717371
ar71xx: add gpios and usb for wzr-hp-g450h
...
SVN-Revision: 29509
2011-12-13 13:33:44 +00:00
4ca2d86493
ar71xx: use RedBoot parser on PB44
...
SVN-Revision: 29501
2011-12-11 15:52:47 +00:00
934eef78ca
convert to gpiolib
...
Signed-off-by: karlp@tweak.net.au
SVN-Revision: 29486
2011-12-09 07:52:10 +00:00
6e69765559
ar71xx: fix WNDR3x00 factory image generation
...
Factory images for WNDR3700v2 and WNDR3800 should contain these model IDs
for the device: field in their DNI tags, not WNDR3700.
This regressed in r29434, which redid WNDR3x00 model detection. The sixth
parameter to Image/Build/Netgear is only used as the -B argument to
mkdniimg, which is used to set the device: field. In r29434, this was
erroneously changed to be WNDR3700 for all models. The tools to flash
factory images (U-Boot's TFTP server and the factory software's upgrade
utility) may refuse to honor images with incorrect device: fields in their
DNI tags.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29473
2011-12-07 06:55:50 +00:00
8eb8a6e1e7
ar71xx: fix WNDR3x00 model detection
...
Detect the model name for /tmp/sysinfo/model based on 10 bytes at offset
56 in the art (caldata) mtd partition.
r29434 redid WNDR3x00 model detection, attempting to distinguish between
WNDR3700v2 and WNDR3800 by checking MemTotal in /proc/meminfo. However, it
contained a bug: it put the awk inside a $(...), with the result that all
WNDR3700v2 and WNDR3800 models would be reported as WNDR3800. This patch
checks the model name stored in the art partition, as is done by U-Boot
shipping on the WNDR3800. It has the likely advantage of working with
future models based on the WNDR3700 board. It also will not mis-detect
units on which people install more memory.
I have tested this patch on WNDR3700 (v1), WNDR3700v2, and WNDR3800.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29472
2011-12-07 06:55:39 +00:00
43bd4c6ad1
ramips: fix mac addresses on the DIR-300/600 boards
...
SVN-Revision: 29471
2011-12-06 20:06:08 +00:00
e33bb9ec66
linux: update 3.1 to 3.1.4
...
SVN-Revision: 29470
2011-12-06 19:50:30 +00:00
6e2ae90f4a
linux: update 3.0 to 3.0.12
...
SVN-Revision: 29469
2011-12-06 19:50:25 +00:00
c6b2b98812
ar71xx: create firmware image for the TL-WR740N/ND v4 boards
...
Based on a patch by Cristian Deluxe <djcristiandeluxe@gmail.com>
SVN-Revision: 29468
2011-12-06 16:26:44 +00:00
fbfad4e9b4
ar71xx: use hw_id, hw_rev and flash_layout with mktplinkfw
...
SVN-Revision: 29467
2011-12-06 16:26:43 +00:00
d753e08c79
ar71xx: fix TL-MR3x20 profile names in image/Makefile
...
SVN-Revision: 29463
2011-12-06 13:53:21 +00:00
62d8009cdd
ar71xx: cleanup TP-Link profiles
...
SVN-Revision: 29461
2011-12-06 10:29:25 +00:00
f7a482d382
ar71xx: add TP-Link board detection
...
SVN-Revision: 29459
2011-12-05 21:11:01 +00:00
bdc2eca7de
ar71xx: use correct mac on the lan interface on several TP-LINK devices
...
SVN-Revision: 29458
2011-12-05 21:10:58 +00:00
0103069372
ar71xx: allow to pass negative offset values for ar71xx_init_mac
...
SVN-Revision: 29457
2011-12-05 21:10:55 +00:00
ada92aee62
ar71xx: don't register PCI controller on AR934x if PCIE_RC bit is not set
...
SVN-Revision: 29456
2011-12-05 18:21:15 +00:00
c6bcf8d1d8
ar71xx: verify hardware id of firmware images on TP-Link boards
...
SVN-Revision: 29455
2011-12-05 18:11:51 +00:00
5ef6ec4a31
ramips: set mac addresses for the NBG-419N
...
Based on a patch by Nerijus Baliunas <nerijus@users.sourceforge.net>
SVN-Revision: 29454
2011-12-05 17:27:07 +00:00
750d560767
ramips: set preinit interface mac on the hw550-3g board
...
Based on a patch by Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29453
2011-12-05 17:27:06 +00:00
b5d7b359b2
ramips: use ramips_get_mac_* functions in the preinit script
...
SVN-Revision: 29452
2011-12-05 17:27:04 +00:00
4d5b940e66
ramips: move ramips_get_mac_* functions to lib/ramips.sh
...
SVN-Revision: 29451
2011-12-05 17:27:03 +00:00
cc853acb3a
ramips: add ramips_ prefix to get_mac_{binary,nvram} functions
...
SVN-Revision: 29450
2011-12-05 17:27:02 +00:00
b1137d48a4
ramips: fix network configuration setup
...
SVN-Revision: 29448
2011-12-05 16:54:48 +00:00
4dc9092f4b
ar71xx: reclaim some unused space on TP-Link boards
...
With the default OpenWrt configuration, this increases the size
of the rootfs_data partition by 384KB/128KB on the older/newer
TP-Link models.
SVN-Revision: 29447
2011-12-05 14:52:36 +00:00
3e7a6d182a
ar71xx: check squashfs signature in TP-Link mtd parser
...
SVN-Revision: 29446
2011-12-05 14:52:33 +00:00
feebf484ba
ar71xx: use the lzma-loader on TP-Link boards w/o lzma support
...
SVN-Revision: 29444
2011-12-05 14:52:28 +00:00
d42968351f
ar71xx: add lzma loader
...
SVN-Revision: 29443
2011-12-05 14:52:25 +00:00
1f809532de
ar71xx: add preliminary support for wzr-hp-g450h
...
SVN-Revision: 29441
2011-12-05 14:20:51 +00:00
d1f63f8538
ar71xx: move multi-m25p80 concat code from wzr-hp-ag300h mach code to dev-m25p80.c, other buffalo routers use it as well
...
SVN-Revision: 29440
2011-12-05 14:20:44 +00:00
4cc2b9bb06
ar71xx: rewrite WNDR3700/3800 handling
...
SVN-Revision: 29434
2011-12-05 13:03:54 +00:00
78699c2e51
add some missing wndr3800 base-files definitions
...
SVN-Revision: 29433
2011-12-05 12:56:21 +00:00
5177814ade
ar71xx: change user-space board detection
...
SVN-Revision: 29432
2011-12-05 12:56:20 +00:00
8a3a60fc64
ar71xx: allow WNDR3700 image creation to fail if kernel/rootfs too big
...
SVN-Revision: 29431
2011-12-05 12:47:53 +00:00
56c9b50006
ramips: fix argus board rootfs size
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29422
2011-12-04 15:24:57 +00:00
7cfa39f032
ar71xx: use the tp-link parser on the tp-link boards
...
Also remove static partition maps.
SVN-Revision: 29416
2011-12-03 18:13:31 +00:00
514b1167c9
ar71xx: add mtd partition parser for the TP-Link boards
...
SVN-Revision: 29415
2011-12-03 18:13:27 +00:00
fc7fb29bae
ar71xx: run the RedBoot parser only on the RedBoot based boards
...
SVN-Revision: 29414
2011-12-03 18:13:25 +00:00
9cc28d5aa0
ar71xx: run the MyLoader parser only on the WP543 board
...
SVN-Revision: 29413
2011-12-03 18:13:23 +00:00
67a0b9aada
ar71xx: run the wrt160nl parser only on the WRT160NL board
...
Also remove static mtd partition definitions.
SVN-Revision: 29412
2011-12-03 18:13:20 +00:00
c8acd6e013
ar71xx: allow to pass part_probe types to the m25p80 driver
...
SVN-Revision: 29411
2011-12-03 18:13:18 +00:00
20483faed0
ar71xx: create initramfs images for the newer TP-Link boards
...
SVN-Revision: 29410
2011-12-03 16:57:23 +00:00
9a2005e5e6
ar71xx: remove swconfig and wpad-mini from custom profiles
...
SVN-Revision: 29408
2011-12-03 16:33:41 +00:00
bc1d818610
ar71xx: add uboot-envtools to the default package list
...
SVN-Revision: 29407
2011-12-03 16:33:40 +00:00
a02a9c3f8b
ar71xx: reclaim unused space in WNDR3700/3800 images
...
Patch by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29406
2011-12-03 16:33:38 +00:00
ac82296c53
ar71xx: add a profile and build image for the OM2P board
...
[juhosg: the name of the final image has been changed to
'openwrt-ar71xx-generic-om2p-squashfs-factory.bin']
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
SVN-Revision: 29397
2011-12-01 22:49:05 +00:00
f188f1bad5
ar71xx: add support for Ubiquiti AirRouter
...
Signed-off-by: Gergely Barta <gergely.barta@printerfairkft.hu>
SVN-Revision: 29395
2011-12-01 22:49:02 +00:00
0612667c34
ar71xx: configure default led behavior for the OM2P
...
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
SVN-Revision: 29394
2011-12-01 22:48:59 +00:00
3fccc3b376
ramips: enable sysupgrade on the RT-N15 board
...
SVN-Revision: 29393
2011-12-01 22:48:58 +00:00
4b2d1c3ad3
ramips: wrap long line in platform upgrade script
...
SVN-Revision: 29392
2011-12-01 22:48:57 +00:00
d622263588
ramips: add profile for the Asus RT-N15
...
This uses previously submitted rtl8366 kernel packages.
[juhosg: The kmod-gpio-dev package has been removed from the package list.]
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29391
2011-12-01 22:48:55 +00:00
3a9e02fa41
ramips: setup default network configuration for RT-N15
...
Based on a patch by Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29390
2011-12-01 22:48:54 +00:00
fc61c107f0
ramips: rt288x: add swconfig and rtl8366{s,_smi} drivers to the default profile
...
It is needed by the RT-N15 board.
SVN-Revision: 29389
2011-12-01 22:48:53 +00:00
80221fcd2a
ramips: remove default network configuration, and generate that from uci-defaults
...
SVN-Revision: 29387
2011-12-01 22:48:51 +00:00
4f6c58adac
ramips: use /lib/functions/uci-defaults.sh
...
SVN-Revision: 29386
2011-12-01 22:48:48 +00:00
39348e387f
ar71xx: use /lib/functions/uci-defaults.sh
...
SVN-Revision: 29385
2011-12-01 22:48:47 +00:00
569d8de6d6
ramips: simplify uci-defaults/network script
...
SVN-Revision: 29383
2011-12-01 22:48:45 +00:00
66c9a351dd
ramips: setup mac and network interfaces from separate functions
...
SVN-Revision: 29382
2011-12-01 22:48:43 +00:00
62d18e9f9a
ramips: fix Asus RT-N15 board support
...
Fix Asus RT-N15 flash partitions and make an image.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29381
2011-12-01 22:48:42 +00:00
2dd79d55c7
ramips: Sparklan wcr-150gn board fixes
...
* Fix partition sizes.
* Add buttons and leds.
* Register usb.
* Remove unnecessary stuff from image Makefile
* Fix rt2x00 eeprom extract.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29380
2011-12-01 22:48:41 +00:00
7c678e7511
ramips: fix package name of kmod-input-gpio-buttons
...
Based on a patch from Omnima Limited.
SVN-Revision: 29379
2011-12-01 22:48:39 +00:00
2ed38b24a8
ramips: move kmod-rt2800-pci to DEFAULT_PACKAGES
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29378
2011-12-01 22:48:38 +00:00
295e04084c
ramips: setup bc2 mac addresses from the generic network script
...
SVN-Revision: 29377
2011-12-01 22:48:37 +00:00
02f95d4fb3
ramips: combine network setup for all boards in one file
...
Inspired by the patch from Roman Yeryomin. Thanks, Roman!
This removes unnecessary duplication and simplifies network setup for new
boards. It would be a one line change most likely.
[juhosg: setup lan and wan interfaces for unspecified rt3x0x based boards
in order to avoid regression]
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
SVN-Revision: 29376
2011-12-01 22:48:35 +00:00
88cb7ae104
omap24xx: bump to 3.1.3
...
SVN-Revision: 29349
2011-11-28 12:46:18 +00:00
bf7316424c
lantiq: bump to 3.1.3
...
SVN-Revision: 29348
2011-11-28 10:22:58 +00:00
5e83009a52
targets: fix CONFIG_USB_STORAGE_* inconsistency
...
* all options were switched from bool to tristate in 2.6.30
* add/change/move them to generic, disabled by default
* remove extinct CONFIG_USB_STORAGE_DPCM dropped in 2.6.29, merged with CONFIG_USB_STORAGE_SDDR09
* remove extinct CONFIG_USB_STORAGE_SIERRA option in 2.6
* cleanup ordering
SVN-Revision: 29337
2011-11-25 20:47:44 +00:00
f20797306a
ar71xx: modify phy mask of the WP543 board
...
This fixes ethernet on newer boards. Based on a patch from #9702 .
SVN-Revision: 29328
2011-11-24 20:09:43 +00:00
c20d7378e5
ar71xx: fix wndr3800 machine name
...
This fixes the machine name in /proc/cpuinfo and luci status page machine name.
Signed-off-by: Petri Rosenström <petri.rosenstrom@gmail.com>
SVN-Revision: 29326
2011-11-24 20:09:38 +00:00
600b6efc41
ar71xx: copy atheros initramfs images to the image directory
...
SVN-Revision: 29325
2011-11-24 20:09:35 +00:00
d97cf76790
ar71xx: specify mtd layout in command line for the DB120 board
...
SVN-Revision: 29324
2011-11-24 20:09:32 +00:00
9389593db9
lantiq: drop 009-MIPS-make-oprofile-use-cp0_perfcount_irq-if-it-is-se.patch
...
This patch is/was a duplicate of generic/patches-3.1/307-mips_oprofile_fix.patch
SVN-Revision: 29294
2011-11-23 12:22:15 +00:00
4982ca983c
lantiq: * fixes ath5k eeprom handling * fixes sx76x * adds sx76x to userland api * minor style cleanups
...
Signed-of-by: Andrej Vlašić <andrej.vlasic0@gmail.com>
SVN-Revision: 29292
2011-11-22 18:50:51 +00:00
718907b661
don't package gpioctl by default
...
SVN-Revision: 29288
2011-11-21 16:36:39 +00:00
c33f21ae95
target/uml: export atomic64_* functions on 32-bit x86
...
SVN-Revision: 29287
2011-11-21 14:28:33 +00:00
9990523a0f
ar71xx: set GE0 phy_mask for AR933x
...
SVN-Revision: 29274
2011-11-20 11:30:10 +00:00
b5739aabd9
fix D-Link DSL-2650U image generation
...
SVN-Revision: 29266
2011-11-19 21:34:51 +00:00
8bac0df4ae
linux: update 3.0 to 3.0.9
...
SVN-Revision: 29264
2011-11-19 18:39:12 +00:00
ae90aa4efd
build images for D-Link DSL-2650U ( #9003 )
...
SVN-Revision: 29238
2011-11-18 10:37:03 +00:00
0b86c2648a
omap24xx: Fix cbus nested IRQ acking
...
SVN-Revision: 29237
2011-11-17 22:31:27 +00:00
df2810831c
omap24xx: Fix initialization of software IRQ mask
...
SVN-Revision: 29236
2011-11-17 21:02:00 +00:00
3f92f7dd90
omap24xx: Update 3.1 config
...
SVN-Revision: 29234
2011-11-17 19:35:57 +00:00
4793be2df9
omap24xx: Some retu/tahvo IRQ fixes
...
SVN-Revision: 29233
2011-11-17 18:06:19 +00:00
630bafc5dd
omap24xx: Add basic kexec fixes.
...
SVN-Revision: 29232
2011-11-17 14:57:34 +00:00
06c986984e
omap24xx: Add workaround for omapfb locking bug.
...
SVN-Revision: 29201
2011-11-16 22:34:38 +00:00
0f03e17bd0
Revert r29193
...
SVN-Revision: 29195
2011-11-16 19:03:23 +00:00
93f02b1ba0
omap24xx: Set platform specific optimization flags
...
SVN-Revision: 29194
2011-11-16 19:02:12 +00:00
b058e97af4
n810: Add xmodmap to profile
...
SVN-Revision: 29193
2011-11-16 19:01:19 +00:00
8d66465b08
include bridge and 8021q modules by default
...
SVN-Revision: 29164
2011-11-15 22:24:22 +00:00
bbe96f13a6
lantiq: add runtime generation of /etc/config/network
...
SVN-Revision: 29161
2011-11-15 18:21:00 +00:00
79a4642b40
lantiq: fix falcon build breakage
...
dev-wifi-rt2x00 fails to build on falcon due to missing pci
SVN-Revision: 29129
2011-11-14 18:55:58 +00:00
f27548448b
ar71xx: fix USB LED on the DB120 board
...
SVN-Revision: 29126
2011-11-14 17:43:15 +00:00
6ebbb1329d
ar71xx: add a function for selecting output signal on a given GPIO pin
...
SVN-Revision: 29125
2011-11-14 17:43:14 +00:00
0c1d3617d7
ar71xx: fix GPIO function handling on AR934x
...
SVN-Revision: 29124
2011-11-14 17:43:13 +00:00
aa0c8c4885
ar71xx: add AR71XX_ prefix to GPIO_REG_* defines
...
SVN-Revision: 29123
2011-11-14 17:43:11 +00:00
62a7795afd
ar71xx: merge nand scan patch
...
SVN-Revision: 29122
2011-11-14 17:43:10 +00:00
12dae96097
ar71xx: fix a compiler warning
...
SVN-Revision: 29110
2011-11-14 13:07:47 +00:00
5ae0fd802c
ar71xx: fix GPIO count for AR934x
...
SVN-Revision: 29109
2011-11-14 13:07:45 +00:00
e52269364a
ar71xx: flush DDR writeback buffers for WMAC and PCIe on AR934X
...
SVN-Revision: 29108
2011-11-14 11:49:53 +00:00
3104d70552
ar71xx: use a dummy irq chip for WMAC and PCIe irq hadling
...
SVN-Revision: 29107
2011-11-14 11:49:51 +00:00
42e8ae09b5
ar71xx: add AR934X_RESET_REG_PCIE_WMAC_INT_STATUS defines
...
SVN-Revision: 29106
2011-11-14 11:49:49 +00:00
c15caea360
ar71xx: add an irq parameter for ar724x_pcibios_init
...
SVN-Revision: 29105
2011-11-14 11:49:47 +00:00
cf90b24bb9
ar71xx: remove hardwired interface parameters from mach-* files
...
SVN-Revision: 29103
2011-11-14 07:38:09 +00:00
defc79cb40
ar71xx: force hardwired interface parameters in ar71xx_add_device_eth
...
SVN-Revision: 29102
2011-11-14 07:38:07 +00:00
6f4bc1ce37
ar71xx: use if-else instead of conditional operators in ar71xx_add_device_eth
...
SVN-Revision: 29101
2011-11-14 07:38:05 +00:00
7f787707de
build images for Pirelli A226M ( #10409 )
...
SVN-Revision: 29045
2011-11-13 19:19:22 +00:00
5dc2098448
register uart0 on DWV-S0 boards ( #10409 )
...
SVN-Revision: 29044
2011-11-13 19:19:18 +00:00
56a96ba876
refresh 3.0 patches
...
SVN-Revision: 29043
2011-11-13 19:19:14 +00:00
54da5cf11f
refresh 2.6.39 patches
...
SVN-Revision: 29042
2011-11-13 19:19:10 +00:00
717a4391d7
rename 456-board_DWV-S0_ehci.patch to 456-board_DWV-S0_fixes.patch
...
SVN-Revision: 29041
2011-11-13 19:19:05 +00:00
c093c9df34
fix typo, load ip17xx switch module
...
SVN-Revision: 29039
2011-11-13 18:41:26 +00:00
368bbc510b
ar71xx: enable has_gbit flag on AR724{0,1}
...
SVN-Revision: 29026
2011-11-13 17:36:36 +00:00
15d7016c9f
ar71xx: fixup onboard PCIe chip registration on the DB120 board
...
SVN-Revision: 29022
2011-11-13 12:48:03 +00:00
f623066e60
ar71xx: drop DB120_WMAC_MAC_OFFSET, it is not needed
...
SVN-Revision: 29021
2011-11-13 12:48:01 +00:00
d2316b2a45
ar71xx: ag71xx: add support for getting switch port link status
...
SVN-Revision: 29017
2011-11-13 11:27:04 +00:00
d0db89133c
ar71xx: remove mii_ctrl resources of the ethernet devices
...
SVN-Revision: 29016
2011-11-13 11:27:03 +00:00
34015ed6e8
ar71xx: ag71xx: remove unused mii_ctrl field from struct ag71xx
...
SVN-Revision: 29015
2011-11-13 11:27:01 +00:00
2d882cff23
ar71xx: ag71xx: remove unused mii_cfg related functions and defines
...
SVN-Revision: 29014
2011-11-13 11:27:00 +00:00
538a9493b9
ar71xx: set MII interface speed from the set_speed callbacks
...
SVN-Revision: 29013
2011-11-13 11:26:59 +00:00
93cd46be13
ar71xx: rename set_pll callback to set_speed in ag71xx_platform_data
...
Also rename the corresponding callback functions.
SVN-Revision: 29012
2011-11-13 11:26:57 +00:00
9579bb4267
ar71xx: ag71xx: remove MII interface setup code
...
SVN-Revision: 29011
2011-11-13 11:26:56 +00:00
da64ce8603
ar71xx: configure MII interface type from ar71xx_setup_phy_if_mode
...
SVN-Revision: 29010
2011-11-13 11:26:54 +00:00
0112153a0e
ar71xx: fix occasional kernel hangs during boot on AR934x
...
The patch taken from the linux-mips mailing list.
The Kernel hangs occasionally during boot after
"Calibrating delay loop..". This is caused by the
c0_compare_int_usable() routine in cevt-r4k.c
returning false which causes the system to disable
the timer and hang later. The false return happens
because the routine is using a series of four calls
to irq_disable_hazard() as a delay while it waits
for the timer changes to propagate to the cp0 cause
register. On newer MIPS cores, like the 74K, the
series of irq_disable_hazard() calls turn into ehb
instructions and can take as little as a few clock
ticks for all 4 instructions. This is not enough of
a delay, so the routine thinks the timer is not
working.
This fix uses up to a max number of cycle counter
ticks for the delay and uses back_to_back_c0_hazard()
instead of irq_disable_hazard() to handle the hazard
condition between cp0 writes and cp0 reads.
SVN-Revision: 29009
2011-11-13 11:26:52 +00:00
1afc76ea13
ar71xx: refresh kernel patches
...
SVN-Revision: 29008
2011-11-13 11:26:51 +00:00
d8acb75009
linux: update 3.1 to 3.1.1
...
SVN-Revision: 29007
2011-11-13 10:48:05 +00:00
a8797d0de6
lantiq: add uci-defaults code for handling leds
...
SVN-Revision: 29004
2011-11-12 23:40:21 +00:00
832e02cd77
lantiq: add /lib/lantiq.sh and make hotplug handlers use it
...
SVN-Revision: 29003
2011-11-12 23:40:16 +00:00
5dcbbf0160
lantiq: rename leds
...
SVN-Revision: 29002
2011-11-12 23:40:12 +00:00
d84b7596d9
lantiq: split compat headers out of bsp header patch
...
SVN-Revision: 29001
2011-11-12 23:40:07 +00:00
2cff80f015
lantiq: adds hotplug handler for loading rt2x00 firmware
...
SVN-Revision: 29000
2011-11-12 23:40:01 +00:00
3660c51c40
lantiq: adds hotplug handler for handling buttons and makes w303v work with it
...
SVN-Revision: 28999
2011-11-12 23:39:56 +00:00
4248705108
lantiq: cleanup default package selection
...
SVN-Revision: 28998
2011-11-12 23:39:51 +00:00
eb20ab87e6
lantiq: w303v has its rt2860 eep on the nor flash. tell compat-wireless how to use it
...
SVN-Revision: 28994
2011-11-12 18:41:15 +00:00
bbfaaeffd6
kernel: ar8216: add support for the AR8236 switch
...
SVN-Revision: 28993
2011-11-12 14:09:52 +00:00
ecb3690d0a
kernel: ar8216: move port vlan setup into a separate function
...
SVN-Revision: 28992
2011-11-12 14:09:50 +00:00
5ad763075e
ar71xx: use the button for WPS control on the DB120
...
SVN-Revision: 28990
2011-11-12 12:50:20 +00:00
4555be2bec
ar71xx: register the second ethernet interface on the DB120 board
...
SVN-Revision: 28989
2011-11-12 12:50:19 +00:00
368c6605a0
ar71xx: implement SoC specific phy interface setup
...
SVN-Revision: 28988
2011-11-12 12:50:18 +00:00
21d317b9cc
ar71xx: move phy interface setup into a separate function
...
SVN-Revision: 28987
2011-11-12 12:50:16 +00:00
aff0c84ffa
ar71xx: register both MDIO bus on the DB120 board
...
SVN-Revision: 28986
2011-11-12 12:09:59 +00:00
b144249108
ar71xx: add AR934X specific MDIO registration code
...
SVN-Revision: 28985
2011-11-12 12:09:56 +00:00
f835106c8c
ar71xx: add a secondary mdio bus
...
SVN-Revision: 28984
2011-11-12 12:09:54 +00:00
90a42da270
ar71xx: rename ar71xx_mdio_* structures to ar71xx_mdio0_*
...
SVN-Revision: 28983
2011-11-12 12:09:50 +00:00
9daa2149fd
ar71xx: add an id argument to ar71xx_add_device_mdio
...
SVN-Revision: 28982
2011-11-12 12:09:48 +00:00
b07b687aec
ar71xx: pass netdev and miidev pointer to ar71xx_add_device_dsa
...
SVN-Revision: 28981
2011-11-12 12:09:42 +00:00
Florian Fainelli
John Crispin
Jonas Gorski
Hauke Mehrtens
Gabor Juhos
Felix Fietkau
Luka Perkov
Vasilis Tsiligiannis
Mirko Vogt
Jo-Philipp Wich
Imre Kaloz
Claudio Mignanti
Jens Muecke
Daniel Dickinson
Nicolas Thill
Michael Büsch