ramips: rt288x: add support for the Buffalo WLI-TX4-AG300N board

SVN-Revision: 29612
lede-17.01
Gabor Juhos 2011-12-27 16:56:30 +00:00
parent 250ef0cb72
commit 723d8dd74f
11 changed files with 189 additions and 1 deletions

View File

@ -66,6 +66,9 @@ get_status_led() {
whr-g300n)
status_led="whr-g300n:green:router"
;;
wli-tx4-ag300n)
status_led="buffalo:blue:power"
;;
wl-351)
status_led="wl-351:amber:power"
;;

View File

@ -60,6 +60,7 @@ case "$FIRMWARE" in
wcr-150gn | \
whr-g300n | \
wl-351 | \
wli-tx4-ag300n | \
wr512-3gn)
rt2x00_eeprom_extract "factory" 0 272
;;

View File

@ -30,6 +30,10 @@ ramips_setup_interfaces()
ucidef_add_switch_vlan "rtl8366rb" "2" "4 5t"
;;
wli-tx4-ag300n)
ucidef_set_interface_lan "eth0"
;;
rt-n15)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "rtl8366s" "1" "1"
@ -81,6 +85,11 @@ ramips_setup_macs()
lan_mac=$(ramips_get_mac_binary factory 4)
wan_mac=$(ramips_get_mac_binary factory 40)
;;
wli-tx4-ag300n)
lan_mac=$(ramips_get_mac_binary factory 4)
;;
esac
[ -n $lan_mac ] && ucidef_set_interface_macaddr lan $lan_mac

View File

@ -107,6 +107,9 @@ ramips_board_name() {
*"Sitecom WL-351 v1 002")
name="wl-351"
;;
*"WLI-TX4-AG300N")
name="wli-tx4-ag300n"
;;
*"WZR-AGL300NH")
name="wzr-agl300nh"
;;

View File

@ -27,6 +27,7 @@ platform_check_image() {
rt-g32-b1 | \
rt-n15 | \
v22rw-2x2 | \
wli-tx4-ag300n | \
whr-g300n)
[ "$magic" != "2705" ] && {
echo "Invalid image type."

View File

@ -15,6 +15,7 @@ enum ramips_mach_type {
RAMIPS_MACH_GENERIC,
/* RT2880 based machines */
RAMIPS_MACH_RT_N15, /* Asus RT-N15 */
RAMIPS_MACH_WLI_TX4_AG300N, /* Buffalo WLI-TX4-AG300N */
RAMIPS_MACH_WZR_AGL300NH, /* Buffalo WZR-AGL300NH */
/* RT3050 based machines */

View File

@ -7,6 +7,11 @@ config RT288X_MACH_RT_N15
select RALINK_DEV_GPIO_BUTTONS
select RALINK_DEV_GPIO_LEDS
config RT288X_MACH_WLI_TX4_AG300N
bool "Buffalo WLI-TX4-AG300N board support"
select RALINK_DEV_GPIO_BUTTONS
select RALINK_DEV_GPIO_LEDS
config RT288X_MACH_WZR_AGL300NH
bool "Buffalo WZR-AGL300NH board support"
select RALINK_DEV_GPIO_LEDS

View File

@ -14,5 +14,5 @@ obj-y := irq.o setup.o rt288x.o devices.o clock.o
obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
obj-$(CONFIG_RT288X_MACH_RT_N15) += mach-rt-n15.o
obj-$(CONFIG_RT288X_MACH_WLI_TX4_AG300N) += mach-wli-tx4-ag300n.o
obj-$(CONFIG_RT288X_MACH_WZR_AGL300NH) += mach-wzr-agl300nh.o

View File

@ -0,0 +1,154 @@
/*
* Buffalo WLI-TX4-AG300N board support
*
* Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published
* by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/ethtool.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <asm/mach-ralink/machine.h>
#include <asm/mach-ralink/dev-gpio-buttons.h>
#include <asm/mach-ralink/dev-gpio-leds.h>
#include <asm/mach-ralink/rt288x.h>
#include <asm/mach-ralink/rt288x_regs.h>
#include <asm/mach-ralink/ramips_eth_platform.h>
#include "devices.h"
#define WLI_TX4_AG300N_GPIO_LED_DIAG 10
#define WLI_TX4_AG300N_GPIO_LED_POWER 12
#define WLI_TX4_AG300N_GPIO_LED_SECURITY 13
#define WLI_TX4_AG300N_GPIO_BUTTON_AOSS 0
#define WLI_TX4_AG300N_GPIO_BUTTON_BW_SWITCH 8
#define WLI_TX4_AG300N_GPIO_BUTTON_RESET 9
#define WLI_TX4_AG300N_BUTTONS_POLL_INTERVAL 20
#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition wli_tx4_ag300n_partitions[] = {
{
.name = "u-boot",
.offset = 0,
.size = 0x030000,
.mask_flags = MTD_WRITEABLE,
},
{
.name = "u-boot-env",
.offset = 0x030000,
.size = 0x010000,
.mask_flags = MTD_WRITEABLE,
},
{
.name = "factory",
.offset = 0x040000,
.size = 0x010000,
.mask_flags = MTD_WRITEABLE,
},
{
.name = "kernel",
.offset = 0x050000,
.size = 0x0d0000,
},
{
.name = "rootfs",
.offset = 0x120000,
.size = 0x2d0000,
},
{
.name = "user",
.offset = 0x3f0000,
.size = 0x010000,
},
{
.name = "firmware",
.offset = 0x050000,
.size = 0x3a0000,
},
};
#endif /* CONFIG_MTD_PARTITIONS */
static struct physmap_flash_data wli_tx4_ag300n_flash_data = {
#ifdef CONFIG_MTD_PARTITIONS
.nr_parts = ARRAY_SIZE(wli_tx4_ag300n_partitions),
.parts = wli_tx4_ag300n_partitions,
#endif
};
static struct gpio_led wli_tx4_ag300n_leds_gpio[] __initdata = {
{
.name = "buffalo:blue:power",
.gpio = WLI_TX4_AG300N_GPIO_LED_POWER,
.active_low = 1,
},
{
.name = "buffalo:red:diag",
.gpio = WLI_TX4_AG300N_GPIO_LED_DIAG,
.active_low = 1,
},
{
.name = "buffalo:blue:security",
.gpio = WLI_TX4_AG300N_GPIO_LED_SECURITY,
.active_low = 0,
},
};
static struct gpio_button wli_tx4_ag300n_gpio_buttons[] __initdata = {
{
.desc = "Reset button",
.type = EV_KEY,
.code = KEY_RESTART,
.threshold = 3,
.gpio = WLI_TX4_AG300N_GPIO_BUTTON_RESET,
.active_low = 1,
},
{
.desc = "AOSS button",
.type = EV_KEY,
.code = KEY_WPS_BUTTON,
.threshold = 3,
.gpio = WLI_TX4_AG300N_GPIO_BUTTON_AOSS,
.active_low = 1,
},
{
.desc = "Bandwidth switch",
.type = EV_KEY,
.code = BTN_0,
.threshold = 3,
.gpio = WLI_TX4_AG300N_GPIO_BUTTON_BW_SWITCH,
.active_low = 0,
},
};
static void __init wli_tx4_ag300n_init(void)
{
rt288x_gpio_init(RT2880_GPIO_MODE_UART0);
ramips_register_gpio_leds(-1, ARRAY_SIZE(wli_tx4_ag300n_leds_gpio),
wli_tx4_ag300n_leds_gpio);
ramips_register_gpio_buttons(-1, WLI_TX4_AG300N_BUTTONS_POLL_INTERVAL,
ARRAY_SIZE(wli_tx4_ag300n_gpio_buttons),
wli_tx4_ag300n_gpio_buttons);
rt288x_register_flash(0, &wli_tx4_ag300n_flash_data);
rt288x_register_wifi();
rt288x_register_wdt();
rt288x_eth_data.speed = SPEED_100;
rt288x_eth_data.duplex = DUPLEX_FULL;
rt288x_eth_data.tx_fc = 1;
rt288x_eth_data.rx_fc = 1;
rt288x_register_ethernet();
}
MIPS_MACHINE(RAMIPS_MACH_WLI_TX4_AG300N, "WLI-TX4-AG300N",
"Buffalo WLI-TX4-AG300N", wli_tx4_ag300n_init);

View File

@ -89,6 +89,10 @@ define BuildFirmware/Buffalo
fi; fi
endef
define BuildFirmware/Buffalo2
$(call BuildFirmware/Generic,$(1),$(2),board=$(3),$($(4)),$(5),$(6))
endef
define BuildFirmware/NW718
$(call PatchKernelLzma,$(2),$(3) $($(4)))
mkimage -A mips -O linux -T kernel -C lzma $(call kernel_entry) \
@ -284,9 +288,15 @@ define Image/Build/Profile/RTN15
$(call Image/Build/Template/GENERIC_4M,$(1),rt-n15,RT-N15)
endef
mtdlayout_wlitx4ag300n=mtdparts=physmap-flash.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,832k(kernel),2880k(rootfs),64k(user)ro,3712k@0x50000(firmware)
define Image/Build/Profile/WLITX4AG300N
$(call BuildFirmware/Buffalo2,$(1),wli-tx4-ag300n,WLI-TX4-AG300N,mtdlayout_wlitx4ag300n,851968,2949120)
endef
ifeq ($(CONFIG_RALINK_RT288X),y)
define Image/Build/Profile/Default
$(call Image/Build/Profile/RTN15,$(1))
$(call Image/Build/Profile/WLITX4AG300N,$(1))
endef
endif

View File

@ -93,6 +93,7 @@ CONFIG_RALINK_RT288X=y
# CONFIG_RALINK_RT305X is not set
CONFIG_RAMIPS_WDT=y
CONFIG_RT288X_MACH_RT_N15=y
CONFIG_RT288X_MACH_WLI_TX4_AG300N=y
CONFIG_RT288X_MACH_WZR_AGL300NH=y
CONFIG_RTL8366S_PHY=y
CONFIG_RTL8366_SMI=y