Between kernels 4.20 and 5.0, a new variant of this board has been
introduced ("Single Shot"), and the existing one has been renamed
with the appendix "Double Shot". [1]
This also adjusted the first compatible in the list:
marvell,armada8040-mcbin -> marvell,armada8040-mcbin-doubleshot
This patch updates the OpenWrt implementation of this device by
adjusting the relevant references to that compatible (i.e., our
board name).
To still provide support for 4.19 with our setup, this adds a
small patch to change the compatible there as well.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b1f0bbe2700051886b954192b6c1751233fe0f52
Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The router Nucom R5010UN v2 has the partitions defined for a 8MB flash,
but the flash chip is 16MB size. We are wasting half of the flash.
Fix it and use generic names for partitions.
Fixes: 474cde6123 ("brcm63xx: probe SPI flash through DT")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Set CCACHE_DIR to $(TOPDIR)/.ccache and CCACHE_BASEDIR to $(TOPDIR).
This allows to do clean and dirclean. Cache hit rate for test build
after dirclean is ~65%.
If CCACHE is enabled stats are printed out at the end of building process.
CCACHE_DIR config variable allows to override default, which could be useful
when sharing cache with many builds.
cacheclean make target allows to clean the cache.
Changes from v1:
- remove ccache directory using CCACHE_DIR variable
- remove ccache leftovers from sdk and toolchain make files
- introduce CONFIG_CCACHE_DIR variable
- introduce cacheclean make target
Signed-off-by: Roman Yeryomin <roman@advem.lv>
The current one only looks for mt76x2e and mt7603e, and
does not work for 2 or more same Wi-Fi chips.
Refactor the script to cover those cases.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Define 64m IMAGE_SIZE for flash firmware.bin since the flash size
is 64MB. Define 48m LS_SYSUPGRADE_IMAGE_SIZE for flash sysupgrade.bin
which contains maximum 16MB kernel and 32MB rootfs according to
memory map.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Many Layerscape boards support both flash boot and SD card boot.
And different firmware and sysupgrade.bin are built for the two
boot methods. To identify them, a fix could be done on board name
by adding a postfix "-sdboot" for SD card boot.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
There had been an issue in Layerscape QSPI driver for very long
time, which made squashfs,jffs2 rootfs not work on QSPI NOR.
And the ubifs had been used as a workaround.
Now the issue has been fixed. So convert to use squashfs,jffs2
rootfs on QSPI NOR for Layerscape boards (LS1012ARDB/LS1046ARDB/
LS1088ARDB), and update u-boot bootargs for booting.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Fixes following warnings:
In target/toolchain/files/wrapper.sh line 18:
REALNAME=$(readlink -f $0)
^-- SC2086: Double quote to prevent globbing and word splitting.
--
In target/toolchain/files/wrapper.sh line 20:
REALNAME_BASE=$(basename $REALNAME)
^-------^ SC2086: Double quote to prevent globbing and word splitting.
--
In target/toolchain/files/wrapper.sh line 21:
REALNAME_DIR=$(dirname $REALNAME)
^-------^ SC2086: Double quote to prevent globbing and word splitting.
--
In target/toolchain/files/wrapper.sh line 74:
exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin $GCC_SYSROOT_FLAGS $TARGET_FUNDAMENTAL_CFLAGS $TARGET_ROOTFS_CFLAGS "$@"
^-----------------------^ SC2086: Double quote to prevent globbing and word splitting.
--
In target/toolchain/files/wrapper.sh line 77:
exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin $LD_SYSROOT_FLAGS $TARGET_FUNDAMENTAL_LDFLAGS "$@"
^-----------------------^ SC2086: Double quote to prevent globbing and word splitting.
--
In target/toolchain/files/wrapper.sh line 80:
exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin $TARGET_FUNDAMENTAL_ASFLAGS "$@"
^-----------------------^ SC2086: Double quote to prevent globbing and word splitting.
--
In target/toolchain/files/wrapper.sh line 83:
exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin "$@"
^-----------------------^ SC2086: Double quote to prevent globbing and word splitting.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
At this point in v5.4 kernel we cannot use dwc2_readl() and
dwc2_writel() since they rely on the value hsotg->needs_byte_swap
which cannot be obtained before the controller wakes up.
We should use readl() and writel() to wake up the controller before
calling dwc2_check_core_endianness().
Fixes: 6be0da90a1 ("ramips: refresh patches")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed Fixes: tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
At this moment Linksys EA8500 uses only eth0.
This patch change switch registers, which allow to use eth1 as lan
and eth0 as wan. The method work with similar Linksys EA7500V1
and it work with EA8500.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Brian Onn <brian.a.onn@gmail.com>
Tested-by: Adrian Panella <ianchi74@outlook.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The support for this device's Marvell MV88E6060 switch has been
reported to be broken with kernels 4.19/5.4 (see bug report).
Since this a 4/32 device and it has been confirmed to be working
with stable 19.07 release (kernel 4.14), and since fixing it does
not seem trivial, let's just disable it in master.
Fixes: FS#2524
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Netgear R6020, aka Netgear AC750.
The R6020 appears to be the same hardware as the Netgear R6080,
aka Netgear AC1000, but it has a slightly different flash layout,
and no USB ports.
Specification:
SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB
MAC addresses based on vendor firmware:
LAN *:88 0x4
WAN *:89
WLAN2 *:88 0x4
WLAN5 *:8a 0x8004
The factory partition might have been corrupted beforehand. However,
the comparison of vendor firmware and OpenWrt still allowed to retrieve
a meaningful assignment that also matches the other similar devices.
Installation:
Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6020, and power the R6020 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6020-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6020. After flashing has finished,
power cycle the R6020, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
[slightly extend commit message, fix whitespaces in DTS, align From:
with Signed-off-by]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes the gphy LED pins for Zyxel P-2812 devices. The have
been accidentally altered during a tidy-up operation (see Fixes:
below).
No ports were available, dmesg reported:
[ 0.658577] pinctrl-xway 1e100b10.pinmux: pin io5 already requested by
1e100bb0.stp; cannot claim for 1e108000.eth
[ 0.667566] pinctrl-xway 1e100b10.pinmux: pin-5 (1e108000.eth) status -22
[ 0.685238] lantiq,xrx200-net 1e108000.eth: Error applying setting,
reverse things back
[ 0.693270] lantiq,xrx200-net: probe of 1e108000.eth failed with error -22
Fixes: FS#3188
Fixes: 660200e53d ("lantiq: dts: assign the GPHY LED pins to the
Ethernet controller node")
Suggested-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Willem van den Akker <wvdakker@wilsoft.nl>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There was a bashism in the script. This fixes the script so that it
doesn't actually require bash, and can be run with any POSIX shell as
its shebang suggests.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch is required for pcie@2,0 in mt7623 to work. The patch was originally
added in kernel 4.14, but it has not been ported to 4.19 and later.
Fixes: FS#3217
Tested-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Since commit 298814e6be ("base-files: config_generate: split macaddr with
multiple ifaces") uci MAC address setup will create a device node for each
member iface. But this script might override the device nodes and interfere
with the MAC address setup.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Commit e53ec043ba ("kirkwood: move usb support to modules") has moved
this config symbol into generic configs, so it could be removed from
other configs.
Suggested-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Port device support for DAP-1330 from the ar71xx target to ath79.
Additionally, images are generated for the European through-socket
case variant DAP-1365. Both devices run the same vendor firmware, the
only difference being the DAP_SIGNATURE field in the factory header.
The vendor's Web UI will display a model string stored in the flash.
Specifications:
* QCA9533, 8 MiB Flash, 64 MiB RAM
* One Ethernet Port (10/100)
* Wall-plug style case (DAP-1365 with additional socket)
* LED bargraph RSSI indicator
Installation:
* Web UI: http://192.168.0.50 (or different address obtained via DHCP)
There is no password set by default
* Recovery Web UI: Keep reset button pressed during power-on
until LED starts flashing red, upgrade via http://192.168.0.50
* Some modern browsers may have problems flashing via the Web UI,
if this occurs consider booting to recovery mode and flashing via:
curl -F \
files=@openwrt-ath79-generic-dlink_dap-1330-a1-squashfs-factory.bin \
http://192.168.0.50/cgi/index
The device will use the same MAC address for both wired and wireless
interfaces, however it is stored at two different locations in the flash.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Arduino Yun is a microcontroller development board, based on Atmel
ATmega32u4 and Atheros AR9331.
Specifications:
- MCU: ATmega32U4
- SoC: AR9331
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: SoC internal
- Ethernet: 1x 10/100Mbps
- USB: 1x 2.0
- MicroSD: 1x SDHC
Notes:
- Stock firmware is based on OpenWrt AA.
- The SoC UART can be accessed only through the MCU.
YunSerialTerminal is recommended for access to serial console.
- Stock firmware uses non-standard 250000 baudrate by default.
- The MCU can be reprogrammed from the SoC with avrdude linuxgpio.
Installation:
1. Update U-Boot environment variables to adapt to new partition scheme.
> setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
> setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
> saveenv
2. Boot into stock firmware normally and perform sysupgrade with
sysupgrade image.
# sysupgrade -n -F /tmp/sysupgrade.bin
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Like many boards, the Banana Pi R2 doesn't have permanant storage of
its MAC address, and we store the first random one that the kernel
generates in order to use it later and at least be consistent.
Store it in the FAT boot partition, just as the U7623 board (and others)
do.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The MT7623 SoC has the same SATA block as the MT7622, so enable it in
MT7623 builds too and add it to the DEVICE_PACKAGES for those boards.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The supported MT7623 boards are mostly identical (what with being a
System-on-Chip and all), so unify the DEVICE_PACKAGES for them, and add
ext4 and usb support for them.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Some options were not explicitly specified, causing the kernel build to
drop to interactive mode. Set the missing options.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The DCH-G020 is a Smart Home Gateway for Z-Wave devices.
Specifications:
* QCA9531, 16 MiB Flash, 64 MiB RAM
* On-Board USB SD3503A Z-Wave dongle
* GL850 USB 2.0 Hub (one rear port, internal Z-Wave)
* Two Ethernet Ports (10/100)
Installation:
* Web UI: http://192.168.0.60 (or different address obtained via DHCP)
Login with 'admin' and the 6-digit PIN Code from the bottom label
* Recovery Web UI: Keep reset button pressed during power-on
until LED starts flashing red, upgrade via http://192.168.0.60
* Some modern browsers may have problems flashing via the Web UI,
if this occurs consider booting to recovery mode and flashing via:
curl -F \
files=@openwrt-ath79-generic-dlink_dch-g020-a1-squashfs-factory.bin \
http://192.168.0.60/cgi/index
Known issues:
* Real-Time-Clock is not working as there is currently no matching driver
It is still included in the dts as compatible = "pericom,pt7c43390";
* openzwave was tested on v19.07 (running MinOZW as a proof-of-concept),
but the package grew too big as lots of device pictures were included,
thus any use of Z-Wave is up to the user (e.g. extroot and domoticz)
The device will use the same MAC address for both wired and wireless
interfaces, however it is stored at two different locations in the flash.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Gives users a third option to augment ondemand and performance. Kernel
docs[1] explain differences and this PR empowers users w/ the choice to
select between the older ondemand and newer and more simplistic schedutil
should they wish to use one that is not the performance governor.
1. Documentation/admin-guide/pm/cpufreq.rst
Signed-off-by: John Audia <graysky@archlinux.us>
[fixed From: to match SoB:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The rg21s fails to boot if the kernel is larger than about
2,376 KiB. The ra21s is virtually identical hardware.
Enabling lzma-loader resolves the issue on both the rg21s
and ra21s (see FS#3057 on the issue tracker).
Fixes: FS#3057
Signed-off-by: Furkan Alaca <furkan.alaca@queensu.ca>
Device specification:
SoC: RT5350
CPU Frequency: 360 MHz
Flash Chip: Macronix MX25L6406E (8192 KiB)
RAM: Winbond W9825G6JH-6 (32768 KiB)
5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
1x external antenna
UART (J1) header on PCB (57800 8n1)
Wireless: SoC-intergated: 2.4GHz 802.11bgn
USB: None
8x LED, 2x button
Flash instruction:
Configure PC with static IP 192.168.99.8/24 and start TFTP server.
Rename "openwrt-ramips-rt305x-zyxel_keenetic-lite-b-squashfs-sysupgrade.bin"
to "rt305x_firmware.bin" and place it in TFTP server directory.
Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Sergei Burakov <senior.anonymous@ya.ru>
Adding this has been overlooked when rebasing the commit prior to
merge.
Fixes: ba0f4f0cfd ("ramips: add support for TP-Link RE500 v1")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The patches for arch/arm/boot/dts/Makefile have not been updated
in a syntactically correct way (just body was changed). Fix it.
Fixes: 4a77a060ab ("ipq40xx: add support for Buffalo WTR-M2133HP")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
SoC: MediaTek MT7621ST
WiFi: MediaTek MT7603
Quantenna QT3840BC
Flash: 128M NAND
RAM: 64M
LED: Dual colour red and green
BTN: Reset
WPS
Eth: 4 x 10/100/1000 connected to MT7621 internal switch
MT7621 RGMII port connected to Quantenna module
GPIO: Power/reset of Quantenna module
Quantenna module
----------------
The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation. It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621. It loads both a second uboot stage and an os
image from the MT7621 using tftp. The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.
There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.
Serial ports
------------
Two serial ports with headers:
RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1 - 57600 8N1 - Connected to the MT7621 console
Both share pinout with many other Zyxel/Mitrastar devices:
1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND
Dual system partitions
----------------------
The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.
OpenWrt does not support this scheme and will always use the
first OS partition. It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.
Installation from vendor firmware
---------------------------------
1. Run a DHCP server. The WAP6805 is configured as a client device
and does not have a default static IP address. Make a note of
which address it is assigned
2. tftp the OpenWrt initramfs-kernel.bin image to this address.
Wait for the WAP6805 to reboot.
3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
backup of all mtd partitions now. The last used OEM image is
still present in either "Kernel" or "Kernel2" at this point,
and can be restored later if you save a copy.
4. sysupgrade to the OpenWrt sysupgrade.bin image.
Installation from U-Boot
------------------------
This requires serial console access
1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
your tftp server directory. Configure the server address as
192.168.0.33/24
2. Hit ESC when the message "Hit ESC key to stop autoboot"
appears
3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.
4. Answer Y to the question "Erase Linux in Flash then burn new
one. Are you sure?", and answer the address/filename questions.
Defaults:
Input device IP (192.168.0.2)
Input server IP (192.168.0.33)
Input Linux Kernel filename ("ras.bin")
5. Wait until after you see the message "Done!" and power cycle
the device. It will hang after flashing.
6. Continue with step 3 and 4 from the vendor firmware procedure.
Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme. These changes appear to have
broken a few things. The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work. The image selection
scheme is unreliable and inconsistent. A limited U-Boot menu is
available - and used by the above U-Boot install procedure. But
direct booting into an uploaded image does not work, neither with
ram nor with flash. Flashing works, but requires a hard reset after
it is finished.
Reverting to OEM firmware
-------------------------
The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.
ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin
OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required. See above.
Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware. But the branding features do obviously
differ.
LED controller
--------------
Hardware implementation is unknown. The dual-color LED is controlled
by 3 GPIOs:
4: red
7: blinking green
13: green
Enabling both red and green makes the LED appear yellow.
The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds support for the Linksys EA7500 V1 router.
Specification:
- CPU: Qualcomm IPQ8064
- RAM: 256MB
- Flash: NAND 128MB
- WiFi: QCA9982 an+ac + QCA9983 bgn
- Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337)
- USB: 1x USB 3.0 1x USB2.0
- Serial console: RJ-45 115200 8n1 (1V8 Voltage level)
- 2 Buttons
- 1 LED
Known issues:
- Some devices won't flash via web gui
Installation:
- Newer stock images doesn't allow to install custom firmware.
- Please downgrade software to 1.1.2 version. Official firmware:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img
- Do it two times to downgrade all stored images.
- Apply factory image via web-gui.
Serial + TFTP method:
- downgrade to 1.1.2 two times
- connect ehternet and serial cable
- set ip address of tftp server to 192.168.1.254
- put openwrt factory image to tftp folder and rename it to macan.bin
- stop device while booting in u-boot
- run command: "run flashimg"
- run command: "setenv boot_part 1"
- run command "saveenv"
- reset
Back to stock:
- Please use old non-gpg image like this 1.1.2:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img
- ssh to router and copy image to tmp
- use sysupgrade -n -F
Tested by github users: @jack338c and @grzesiczek1
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.
Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A
Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
# ubidetach -p /dev/mtd15
# ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
# fw_setenv bootcmd bootipq
8. Perform reboot.
Recover to stock firmware
-------------------------
1. Execute the following command.
# fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Zyxel NSA310S is a NAS based on Marvell kirkwood SoC.
Specification:
- Processor Marvell 88F6702 1 GHz
- 256MB RAM
- 128MB NAND
- 1x GBE LAN port (PHY: Marvell 88E1318)
- 2x USB 2.0
- 1x SATA
- 3x button
- 7x leds
- serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC)
Known issues:
- no kernel module for RTC. [*]
- buzzer (connected to MPP43) need to be drived by 1kHz signal
- no kernel module for internal MCU connected via I2C[**]
[*]
Karoly Pocsi made simple, unofficial driver for HT1382.
It can be found here:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/
[**]
Karoly Pocsi found how CPU talk with MCU:
It is possible to query the MCU-controlled fan speed and temperature:
i2cget -y 0x0 0x0a 0x07
i2cget -y 0x0 0x0a 0x08
The first value (0x07) is the temperature in ° C, the second (0x08) is
the time in milliseconds to complete one fan revolution (rpm = 60,000 / value).
Info translated from:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/
Installation:
TFTP:
1. Run serial console and go to u-boot.
2. Copy u-boot via tftp and write to NAND:
=> mw 0x0800000 0xffff 0x100000
=> nand erase 0x0 100000
=> setenv ipaddr 192.168.1.2
=> setenv serverip 192.168.1.4
=> tftp 0x0800000 nsa310s-u-boot.kwb
=> nand write 0x0800000 0x0 0x100000
=> reset
3. Run new u-Boot, repair bootcmd and restore MAC address from sticker
=> setenv ethaddr AA:BB:CC:DD:EE:FF
=> saveenv
4. Copy and run initramfs image
=> setenv ipaddr 192.168.1.2
=> setenv serverip 192.168.1.4
=> tftpboot zyxel_nsa310s-initramfs-uImage
=> bootm 0x800000
5. Download sysupgrade image and perform sysupgrade
USB:
1. Prepare usb fat32 drive with u-boot.kwb and initramfs image.
Stick it to USB 2.0 port.
2. Run serial console and go to u-boot.
3. Copy u-boot from usb and write to NAND:
=> mw 0x0800000 0xffff 0x100000
=> nand erase 0x0 100000
=> usb start
=> fatload usb 0 0x0800000 u-boot.kwb
=> nand write 0x0800000 0x0 0x100000
=> reset
4. Run new u-Boot, repair bootcmd and restore MAC address from sticker
=> setenv ethaddr AA:BB:CC:DD:EE:FF
=> saveenv
5. Copy and run initramfs image:
=> usb start
=> fatload usb 0 0x0800000 initramfs-uImage
=> bootm 0x800000
6. Download sysupgrade image and perform sysupgrade.
Based on work ThBexx <thomas.beckler@hotmail.com>
DTS based on dropped support in 0ebdf0c.
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[NSA310s -> NSA310S in DEVICE_MODEL]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specification:
• 650/600/216 MHz (CPU/DDR/AHB)
• 64 MB of RAM (DDR2)
• 32 MB of FLASH
• 2T2R 2.4 GHz
• 2x 10/100 Mbps Ethernet
• 1x USB 2.0 Host socket
• 1x miniPCIe slot
• UART for serial console
• 14x GPIO
Flash instructions:
Upgrading from ar71xx target:
• Upload image into the board:
scp openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin
root@192.168.1.1/tmp/
• Run sysupgrade
sysupgrade -F /tmp/openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin
Upgrading from u-boot:
• Set up tftp server with
openwrt-ath79-generic-8dev_lima-initramfs-kernel.bin
• Go to u-boot (reboot and press ESC when prompted)
• Set TFTP server IP
setenv serverip 192.168.1.254
• Set device ip from the same subnet
setenv ipaddr 192.168.1.1
• Copy new firmware to board
tftpboot 0x82000000 initramfs.bin
• Boot OpenWRT
bootm 0x82000000
• Upload image openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin into
the board
• Run sysupgrade.
Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
Specifications:
SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM: 512 MiB
FLASH1: 16 MiB NOR - SPI0
FLASH2: 8 GiB eMMC
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT: Reset, WPS
LED: Power, Mesh, WLAN
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2: On board with BLE module
SPI1: On board socket for Zigbee module
Install via tftp
- NB: need to flash transition image firstly
Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf
Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"
See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg
Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot
Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo
Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client
1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0
other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)
MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004
Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds cpu frequency setting for AR724x and AR7161.
It is unknown if all the AR71xx devices support the same value range,
so support is only enabled for AR7161 at this stage.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The current code would return an error on ath79 when the SoC isn't known
to the driver. Return the raw hex value instead, as happens with non
supported targets.
Also return the correctly incremented value from
sc_tag_cpufreq_ath79_arraysize()
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
RouterBOOT cpu frequency settings are letter-indexed. Follow the
same logic for the sysfs interface.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The routine would only accurately print out the first word.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 5ecf7d96 ("generic: routerboot sysfs platform driver")
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 128MB
FLASH: 16MB NOR (Macronix MX25L12805D)
ETH: 1x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615 (4x4:4)
- 5GHz: 1x MT7615 (4x4:4)
- 4 antennas: 2 external detachable and 2 internal
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x Green led (Power)
- 1x Green-Amber-Red led (Wifi)
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the factory image directly from OEM web interface.
(You can login using these credentials: admin/1234)
Restore OEM Firmware
--------------------
Flash the OEM "bin" firmware directly from LUCI.
The firmware is downloadable from the OEM web page.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Restoring procedure tested with RE23_1.08.bin
MAC addresses
-------------
factory 0x4 *:24
factory 0x8004 *:25
Cimage 0x07 *:24
Cimage 0x0D *:24
Cimage 0x13 *:24
Cimage 0x19 *:25
No other addresses were found in factory partition.
Since the label contains both the 2.4GHz and 5GHz mac address I decided
to set the 5GHz one as label-mac-device. Moreover it also corresponds
to the lan mac address.
Notes
-----
The wifi led in the OEM firmware changes colour depending on the signal
strength. This can be done in OpenWrt but just for one interface.
So for now will not be any default action for this led.
If you want to open the case, pay attention to the antenna placed on
the bottom part of the front cover.
The wire is a bit short and it breaks easily. (I broke it)
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[fix two typos and add extended MAC address section to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This Fixes the folowing compile error:
drivers/mtd/nand/rb91x_nand.c: In function 'rb91x_nand_remove':
drivers/mtd/nand/rb91x_nand.c:445:16: error: 'rbni' undeclared (first use in this function)
nand_release(&rbni->chip);
Fixes: ce958dd88a ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes following build failures:
WARNING: Image file glinet_gl-ar750s-nor-kernel.bin is too big
WARNING: Image file glinet_gl-ar750s-nor-nand-kernel.bin is too big
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This moves WiFi LED triggers from 01_leds to device tree.
While at it, convert the labels there to lower case; this is
more commonly used and the change will actually remove competition
between DT trigger and leftover uci config on already installed
systems.
Suggested-by: Georgi Vlaev <georgi.vlaev@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As the reported major bugs are ironed out, switch to the new kernel to
begin testing with a broader audience.
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix inconsistencies found in DTS files and sort ethernet ports based on
updated names.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[squash two separate patches, rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The removed lines are already included in vr9_avm_fritz736x.dtsi
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move the USB VBUS regulator nodes out of the GPIO controller node. This
fixes a problem where the "regulator-fixed" driver wasn't probed for
these regulators because the GPIO driver doesn't scan the child-nodes
and based on the dt-bindings documentation it's not supposed to.
This fixed the following error reported by Luca Olivetti:
...
dwc2 1e101000.usb: DWC OTG Controller
dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
dwc2 1e101000.usb: irq 62, io mem 0x1e101000
dwc2 1e101000.usb: startup error -517
dwc2 1e101000.usb: USB bus 1 deregistered
dwc2 1e101000.usb: dwc2_hcd_init() FAILED, returning -517
Fixes: FS#1634
Cc: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Upstream commit 3d00da1de3 ("platform/x86: pcengines-apuv2: detect apuv4
board")
On 5.4, this module fails on APUv4 due to non-matching DMI data. With this
patch, the module will match DMI data for the APUv4.
Signed-off-by: Matthew Gyurgyik <matthew@gyurgyik.io>
[include upstream patch description]
Signed-off-by: David Bauer <mail@david-bauer.net>
Add missing switch config (4 LAN-Ports + CPU).
Grey WAN port (used for ADSL) is not part of the switch.
Signed-off-by: Lars Wessels <software@bytebox.org>
[rework commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Set wifi mac from flash partition 'board_config' to
match the label on the device (Easybox 802).
Currently the wifi mac is always set to 00:0c:43:28:60:00.
eth0 and WiFi will now share the same mac (as in original firmware).
Signed-off-by: Lars Wessels <software@bytebox.org>
[improve commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Reduce spi-max-frequency for ipTIME A8004T and disable
m25p,fast-read option.
A8004T uses `en25qh128` for the MTD.
This flash memory would allow 80MHz, sometimes kernel received
wrong id value in initramfs installed router.
(kernel expected `1c 70 18 1c 70 18`, but one of cases, it
was `9c 70 18 1c 70 18`)
In this case, openwrt can't detect the partition information,
it would write the inccorect data to the firmware partition and
also it would occur the bootlooping after sysupgrade.
Signed-off-by: Sunguk Lee <d3m3vilurr@gmail.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All device DTS files in the target set the serial0 property to the
same value (*). So, let's move the definitions to the DTSI files.
That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).
* The only exception is ipq8064-db149, which defines
"serial0 = &uart2;", but inside a block called "alias" instead of
"aliases". It must be assumed that this is broken anyway, so we
don't touch it here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All device DTS files in the target set the stdout-path to the same
value. So, let's move the definitions to the DTSI files.
That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, the DTSI files on ipq806x had a linear inheritance:
qcom-ipq8064.dtsi
v
qcom-ipq8064-v1.0.dtsi
v
qcom-ipq8064-v2.0.dtsi
v
qcom-ipq8065.dtsi
This poses problems when one wants to set something that is specific
to an architecture closer to the top of the tree.
In this patch, we remove the chain-like inheritance and have all
other files derived from qcom-ipq8064.dtsi (changing this name to
something more generic is not possible due to upstream use).
The removal of inheritance will require a few entries to be copied
from qcom-ipq8064-v2.0.dtsi to qcom-ipq8065.dtsi. However, it also
opens an opportunity for some clean-up:
- Many definitions can be improved by just using the innermost labels.
- Instead of disabling the CPU_SPC node for ipq8065, it is now off by
default and enabled where needed.
- Instead of patching phy-tx0-term-offset into qcom-ipq8064.dtsi and
then having it changed for qcom-ipq8064-v2.0/qcom-ipq8065, just have
the appropriate settings done in the lower DTSI files directly.
- For the opp_table0 adjustments for ipq8065, just redefine what's
changed, but don't add all the untouched properties again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As almost same pinmux nodes are repeated in each device dts,
let's define them once in the ipq8064 dtsi and remove the rest.
* uart0_pins : Did not touch.
* i2c4_pins : This node seems to be not used at all in dts.
Added the most common form in the dtsi. Did not touch rpm_pins.
* spi_pins : The common mux node is already present in the dtsi.
Removed the duplicate nodes from dts.
* nand_pins : Moved the entire node.
* mdio0_pins : Moved the common mux node.
* rgmii2_pins: Moved the common mux node. "pins" property is overrided in ap161.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
There is one closing bracket too much.
Fixes: ce958dd88a ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We are setting CONFIG_I2C_PXA is not set
If you do set pxa to y then you have issues if you do not have
CONFIG_I2C_PXA_SLAVE is not set
Fixes: dd13add3ce ("kernel: i2c-pxa: remove slave")
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
The Buffalo Linkstation LS421DE has a chassis fan for cooling two internal
hard drives. Currently there is no control over this fan, running always
at fixed medium speed.
With the recent jump to the kernel 5.4, now we can monitor the hard drive
temperature and control the fan with thermal zones.
Install the kmod-hwmon-drivetemp module and wire up a thermal zone on the
dts file to allow automatic fan control by the kernel.
Tested succesfully using a single Crucial BX500 SSD drive.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Run tested: ath79
Build tested: ath79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Build tested: ramips
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This resolves a hazard between a mtc0 and a mfc0 instruction after
activating the DSP support. Without this fix the CPU could use the old
value again and the DSP support would not be active.
Fixes: FS#2928, FS#2899
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300]
Tested-by: David Bauer <mail@david-bauer.net> [ocedo_koala/ocedo_raccoon]
Add support for the ar71xx supported GL.iNet GL-MiFi to ath79.
Specifications:
- Atheros AR9331
- 64 MB of RAM
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet
- 2.4GHz (AR9330), 802.11b/g/n
- 1x USB 2.0 (vbus driven by GPIO)
- 4x LED, driven by GPIO
- 1x button (reset)
- 1x mini pci-e slot (vcc driven by GPIO)
Flash instructions:
Vendor software is based on openwrt so you can flash the sysupgrade
image via the vendor GUI or using command line sysupgrade utility.
Make sure to not save configuration over reflash as uci settings
differ between versions.
Note on MAC addresses:
Even though the platform is capable to providing separate MAC addresses
to the interfaces vendor firmware does not seem to take advantage of
that. It appears that there is only single unique pre-programmed
address in the art partition and vendor firmware uses that for
every interface (eth0/eth1/wlan0). Similar behaviour has also been
implemented in this patch.
Note on GPIOs:
In vendor firmware the gpio controlling mini pci-e slot is named
3gcontrol while it actually controls power supply to the entire mini
pci-e slot. Therefore a more descriptive name (minipcie) was chosen.
Also during development of this patch it became apparent that the
polarity of the signal is actually active low rather than active high
that can be found in vendor firmware.
Acknowledgements:
This patch is based on earlier work[1] done by Kyson Lok. Since the
initial mailing-list submission the patch has been modified to comply
with current openwrt naming schemes and dts conventions.
[1] http://lists.openwrt.org/pipermail/openwrt-devel/2018-September/019576.html
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Based on "make kernel_menuconfig CONFIG_TARGET=generic" and 5.4.49
CONFIG_LEDS_TRIGGER_DISK has been removed by the refresh and added
back manually in order to not revert f93fcf8923 ("ipq806x: enable
disk-activity LED trigger").
Signed-off-by: John Audia <graysky@archlinux.us>
[extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Pogoplug V4 has a reset button on a GPIO pin.
To use it, kmod-gpio-button-hotplug package needs to be installed.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
All definitions of gpio in SoC DTSI files do not set status, i.e.
have it enabled. This drops all remaining redundant "status = okay"
definitions in descendent files (mostly older ones).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All other SoC DTSI files have gpio enabled by default, only
ar9330/ar9331 disable it by default, only to have it enabled again
afterwards for each individual device.
So, do not disable it in the first place, and drop all device-specific
status statements afterwards.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SoC: AR9344
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 Gigabit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 48V IEEE 802.3af/at - 24V passive optional
USB 2.0 header
Installation:
To install, either start tftp in bin/targets/ath79/generic/ and use
the u-boot prompt over UART:
tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj344-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot
The cpximg file can be used with sysupgrade in the stock firmware (add
SSH key in luci for root access) or with the built-in cpximg loader.
The cpximg loader can be started either by holding the reset button
during power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.
For example, if the board is labelled '6A08':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj344-16m-squashfs-cpximg-6a08.bin
MAC addresses:
<&uboot 0x2e010> *:99 (label)
<&uboot 0x2e018> *:9a
<&uboot 0x2e020> *:9b
<&uboot 0x2e028> *:9c
Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[minor commit message adjustments, drop gpio in DTS, DTS style fixes,
sorting, drop unused cpximg recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.
Specifications
MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.
Web Interface Installation
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Signed-off-by: Rowan Border <rowanjborder@gmail.com>
From upstream:
b8392808eb3f sch_cake: add RFC 8622 LE PHB support to CAKE diffserv handling
3f608f0c4136 sch_cake: fix a few style nits
8c95eca0bb8c sch_cake: don't call diffserv parsing code when it is not needed
9208d2863ac6 sch_cake: don't try to reallocate or unshare skb unconditionally
From netdev not yet accepted:
sch_cake: fix IP protocol handling in the presence of VLAN tags
The VLAN tag handling is actually wider than just cake so upstream are
working out how to fix it generically. We fix it here just for cake.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This was backported to 4.19 and I clearly expected it to land in 5.4 but
it didn't (5.5) so backport it to 5.4 for consistency.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Cudy WR1000 and Wavlink WL-WN577A2 store WAN as well as label MAC address
at the same position in flash.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: David Bauer <mail@david-bauer.net>
This package allows to read battery status information and control the
power state of the RAVPower RP-WD009 power management IC.
Signed-off-by: David Bauer <mail@david-bauer.net>
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.
Hardware
--------
CPU: MediaTek MT7628AN
RAM: 64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN: MediaTek MT7628AN 2T2R b/g/n
MediaTek MT7610E 1T1R n/ac
ETH: 1x FastEthernet
SD: SD Card slot
USB: USB 2.0
Custom PMIC on the I2C bus (address 0x0a).
Installation
------------
1. Press and hold down the reset button.
2. Power up the Device. Keep pressing the reset button for 10
more seconds until the Globe LED lights up.
3. Attach your Computer to the Ethernet port. Assign yourself the
address 10.10.10.1/24.
4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
factory image.
5. The flashing will take around 1 minute. The device will reboot
automatically into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
The replaces the custom uImageArcher build step with the generic uImage
build step. The only different between these two is the difference in
the generated name.
Tested on: TP-Link Archer C59 v1
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band
wall-plug wireless router. In Germany this device is sold under the brand
name Maginon WL-755 (white case):
Device specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps (Ralink RT3050)
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: 1 programmable (WPS) + LAN, WAN, POWER
- Buttons: Reset, WPS
- Small sliding power switch
Flashing instructions (U-boot):
- Configure a TFTP server on your PC/Laptop and set its IP
to 192.168.10.100
- Rename the OpenWrt image to firmware.bin and place it in the
root folder of the TFTP server
- Power off (using the small sliding power switch on the left
side) the device and connect an ethernet cable from its LAN
or WAN port to your PC/Laptop
- Press the WPS button (and keep it pressed)
- Power on the device (using the small power switch)
- After a few seconds, when the WAN/LAN LED stops blinking
very fast, release the WPS button
- Flashing OpenWrt takes less than a minute, system will
reboot automatically
- After reboot the WPS LED will indicate the current OpenWrt
running status
Signed-off-by: Lars Wessels <software@bytebox.org>
[removed unused labels - fix whitespace errors - wrap commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
The Device/Default definition in mvebu defines an IMAGE/factory.img
which is not included in IMAGES, and only used twice in the
individual definitions. Move it out of the default definition
to keep it closer to the reassignment of IMAGES and make it more
consistent with respect to other values of IMAGE/factory.img
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.
Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.
Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For quite some time, the tiny (4M flash) TP-Link sysupgrade and
factory images cannot be built anymore by the buildbots, just
the initramfs-kernel.bin files are still there.
Disable these images for the buildbots and prevent useless builds.
Note that these devices still build fine with default settings,
even for kernel 5.4.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In 02_network, the board name solidrun,clearfog-a1 is used in a
case, but it does not seem to be used/exist anywhere else in OpenWrt.
The valid strings are:
- solidrun,clearfog-pro-a1
- solidrun,clearfog-base-a1
Fixes: 12795ec9f1 ("mvebu: split interface configuration for
clearfog pro and base")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Generate additional images that are compatible to the cpximg loader.
The cpximg loader can be started either by holding the reset button during
power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.
For example, if the board is labelled '7A04':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin
These files can also be used with the sysupgrade utility in stock images (add
SSH key in luci for root access).
Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix sorting of definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SoC: QCA9531
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 100MBit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 24V - 48V IEEE 802.3af optional
USB 2.0 header
Installation:
To install, start a tftp server in bin/targets/ath79/generic/ and use the
u-boot prompt over UART:
tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj531-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot
The cpximg file can be used with sysupgrade in the stock firmware (add SSH key
in luci for root access).
Another way is to hold the reset button during power up or running 'cpximg' in
the u-boot prompt.
Once the last LED starts flashing regularly, a TFTP-server under 192.168.1.1
will accept the image appropriate for the board revision that is etched on the
board.
For example, if the board is labelled '7A04':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin
MAC addresses:
<&uboot 0x2e010> *:cb (label)
<&uboot 0x2e018> *:cc
<&uboot 0x2e020> *:cd
<&uboot 0x2e028> *:ce
Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message facelift, fix rssileds, add led aliases]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The WAC124 hardware appears to be identical to R6260/R6350/R6850.
SoC: MediaTek MT7621AT
RAM: 128M DDR3
FLASH: 128M NAND (Macronix MX30LF1G18AC)
WiFI: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 nac 4T4R
ETH: SoC Integrated Gigabit Switch (1x WAN, 4x LAN)
USB: 1x USB 2.0
BTN: Reset, WPS
LED: Power, Internet, WiFi, USB (all green)
Installation:
The factory image can be flashed from the stock firmware web interface
or using nmrpflash. With nmrpflash it is also possible to revert to
stock firmware.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This adds support for the Netgear R6080, aka Netgear AC1000.
The R6080 has almost the same hardware as the Netgear R6120,
aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and
uses a different SERCOMM_HWID.
Specification:
SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB
Installation:
Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6080, and power the R6080 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6080. After flashing has finished,
power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[rebase and adjust for 5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
switch-bcm53xx-mdio does not exists, use kmod-switch-bcm53xx-mdio
instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Tobias Schramm <tobleminer@gmail.com>
- Delete useless HDD presence inputs: they aren't buttons, and probably
they are outputs in the stock firmware.
- Change the Function Button keycode: the current one isn't mapped by
the kernel module.
- Use the recommended property names for the ethernet stuff.
- Add missing i2c pinmux.
- Minor cosmetic changes.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
All boards on xrx200 use builtin switch and there is no supported device
with external switch.
It was copy paste from xway subtarget and was added in commit 18b76c66fb.
Save 20.3 kB flash memory.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
This is fixed in 18.06, it appears again in 19.07.
Currently mt7628 sdcard driver do not support polling mode which is for
the device do not have card-detect pin to detect sd card insert. Without
this patch, device will not detect sdcard is inserted. This patch is a
fix of that.
Signed-off-by: Qin Wei <support@vocore.io>
Support Intel 10 Gigabit Ethernet Cards in x86/64 images by default.
This ensures that systems with cards such as the Intel x520 will work properly.
Signed-off-by: Gregory L. Dietsche <Gregory.Dietsche@cuw.edu>
With this change the LED subsystem is abused in the kernel to switch the
simswap. This change will be reverted, so we could use again the gpio
subsystem.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Add a module description for the new pcengnies-apu2 device driver.
This driver supports the front button and LEDs on the PC Engines
APUv2/APUv3 boards.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.
The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi
Note that while this tidies up master a lot, it might develop into a
frequent pitfall for backports.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
chosen/bootargs are defined to the same value in device DTS files
that is already set in the SoC DTSI. Remove the redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the AVM FRITZ!WLAN Repeater DVB-C
SOC: Qualcomm Atheros QCA9556
RAM: 64 MiB
FLASH: 16 MB SPI-NOR
WLAN: QCA9556 3T3R 2.4 GHZ b/g/n and
QCA9880 3T3R 5 GHz n/ac
ETH: Atheros AR8033 1000 Base-T
DVB-C: EM28174 with MaxLinear MXL251 tuner
BTN: WPS Button
LED: Power, WLAN, TV, RSSI0-4
Tested and working:
- Ethernet (correct MAC, gigabit, iperf3 about 200 Mbit/s)
- 2.4 GHz Wi-Fi (correct MAC)
- 5 GHz Wi-Fi (correct MAC)
- WPS Button (tested using wifitoggle)
- LEDs
- Installation via EVA bootloader (FTP recovery)
- OpenWrt sysupgrade (both CLI and LuCI)
- Download of "urlader" (mtd0)
Not working:
- Internal USB
- DVB-C em28174+MxL251 (depends on internal USB)
Installation via EVA bootloader (FTP recovery):
Set NIC to 192.168.178.3/24 gateway 192.168.178.1 and power on the device,
connect to 192.168.178.1 through FTP and sign in with adam2/adam2:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Wait for "Transfer complete" together with the transfer details.
Wait two minutes to make sure flash is complete (just to be safe).
Then restart the device (power off and on) to boot into OpenWrt.
Revert your NIC settings to reach OpenWrt at 192.168.1.1
Signed-off-by: Natalie Kagelmacher <nataliek@pm.me>
[fixed sorting - removed change to other board -
prettified commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds supports for the NETGEAR R6200 V1
This device is mainlined in Linux as of 5.4
Specification:
- SOC: Broadcom BCM4718A1 (480 MHz)
- Flash: 16MB (Macronix MX25L128)
- RAM: 128MB DDR2
- SWITCH: BCM53125
- Ethernet: 5x GE (1 WAN + 4 LAN, Inverted order)
- WLAN 2.4G: In SOC
- WLAN 5GHz: miniPCIe card, BCM4352 (ID: 4360)
- USB: 1x USB 2.0 port (Type A)
- Buttons: Reset, WLAN, WPS
- LED: Amber for Power, others need a workaround
- UART: 1x UART on PCB
LED Issues: They are controlled by a 74HC164 via bit banging(GPIO 6/7)
Firmware Install Instructions
=============================
Using the device specific .chk, use that file to perform
a normal device upgrade in the OEM admin page.
Signed-off-by: Edward Matijevic <motolav@gmail.com>
This commit performs minor janitorial work to clean up some code
formatting for the Netgear R6120.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
This moves the trigger for the Netgear R6120's wlan2g_green LED from
base-files/etc/board.d/01_leds to the device-tree file.
This has been applied to R6120 based on findings for the very similar
Netgear R6080.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[merge case in 01_leds, slightly adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (armada-3720-uDPU.dts), which is only present
for 4.19, as it has been upstreamed before 5.4.
Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory, only keeping
the named exception to files-4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (qcom-ipq4018-emr3500.dts), which is only
present for 5.4.
Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory.
If there ever was a new kernel with substantial DTS changes, a
new folder would need to be introduced anyway and could easily be
done.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The mwlwifi driver sets the default country code for EU (fi-
rmware region code 0x30) certified devices to FR (France),
not DE (Germany). Whilst this is a trivial fix, novice users
may not know how mwlwifi negatively reacts to a non-matching
country code and may leave the setting alone. Especially si-
nce it is under the advanced settings section in LuCI.
Relevant mwlwifi driver code:
0a550312dd
The mwlwifi driver readme states "Please don't change country
code and let mwlwifi set it for you." However, OpenWrt's current
behaviour does not adhere to this with its default, 'just flashed
from factory' setting for EU devices.
Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upstream in commit f9f8f0c24203 ("crypto: ccp -- don't "select"
CONFIG_DMADEVICES") removed dependency on CONFIG_DMADEVICES symbol which
leads to build breakage of ccp crypto module, so fix this by adding that
symbol back in the kernel config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The ADB P.DG AV4202N device has a wifi chipset connected via PCI. But the
PCI pinmux is missing and without it the wifi won't work properly.
Add the pinctrl_pci to enable the missing PCI pins for this device.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Currently it's not possible to tftpboot initramfs image on archer-c7-v5
as the image contains tplink-v1-header which leads to:
ath> bootm
## Booting image at 81000000 ...
Bad Magic Number
as U-Boot expects uImage wrapped image. This is caused by following
inheritance issue:
define Device/Init
KERNEL_INITRAMFS = $$(KERNEL)
define Device/tplink-v1
KERNEL := kernel-bin | append-dtb | lzma
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | tplink-v1-header
define Device/tplink-safeloader
$(Device/tplink-v1)
define Device/tplink-safeloader-uimage
$(Device/tplink-safeloader)
KERNEL := kernel-bin | append-dtb | lzma | uImageArcher lzma
define Device/tplink_archer-c7-v5
$(Device/tplink-safeloader-uimage)
where tplink-v1 defines KERNEL_INITRAMFS with tplink-v1-header and it's
then used by all devices inheriting from tplink-safeloader. Fix this by
overriding KERNEL_INITRAMFS to KERNEL variable again.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.
The previous patch in 36f628910b was only applied to the 4.19 file,
so let's just make it consistent with this patch.
Cc: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Inputs assigned to "mode select" switch on the side of the device
were missing linux,input-type property.
This would cause them do incorrectly generate EV_KEY events.
Fix this by setting the linux,input-type = <EV_SW> property on them.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Increase the SPI frequency for ELECOM WRC-1900GST and WRC-2533GST
to 40 MHz by updating the common DTSI file.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[WRC-1900GST]
Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link CPE610 v2 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of DDR2 RAM
- 8 MB of SPI-NOR Flash
- 23dBi high-gain directional 2×2 MIMO antenna and a
dedicated metal reflector
- Power, LAN, WLAN5G green LEDs
- 3x green RSSI LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This ports support for these devices from ar71xx.
Specification:
- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: v3: 560 MHz, v4: 650 MHz
- Flash: 4096 KiB
- RAM: 32 MiB
- Ethernet: 1 port @ 100M
- Wireless: SoC-integrated: QCA9533 2.4GHz 802.11bgn
In contrast to the implementation in ar71xx (reset and WiFi button),
the device actually features reset and WPS buttons.
Flashing instructions:
Upload the ...-factory.bin file via OEM web interface.
TFTP Recovery:
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to
wa801ndv3_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
TFTP recovery has only been tested with v3, and the Wiki states
that the procedure won't work for v4, which cannot be verified
or falsified at the moment.
Tested by Tim Ward (see forum):
https://forum.openwrt.org/t/ath79-support-for-tp-link-tl-wa901nd-v3-v4-v5/61246/13
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix the switch LAN labels for the DGND3700v1/DGND3800B router,
the order is reversed.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[cut out of bigger patch, adjust commit title/message accordingly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Huawei Echolife HG622 has hardware controlled LAN LEDs.
Add the ephy led pinctrl to let the router show LAN activity on these
LEDs.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The status is set to "okay" for all devices on ar9344, so just move
this to the parent DTSI.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Define the kernel config symbol CONFIG_MFD_RB4XX_CPLD=n
to fix build breakage on non-mikrotik targets.
The driver was added for all ath79, but the symbol was only
defined for mikrotik subtarget.
Fixes: fa70b3a4bb ("ath79: add Mikrotik rb4xx series drivers")
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[rearrange commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CONFIG_HZ_100 is not set to "y" in generic config anymore since
3a761c90af ("treewide: Don't diverge from upstream default HZ
settings on 4.19"), so we don't need to disable it anymore either.
This was the only remaining case in the entire tree.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently I'm unable to boot initramfs image with `console=ttyS0,115200`
kernel commandline as the kernel commandline mangling resets kernel
commandline if there is no `root=` option provided, efectively clearing
whatever I pass to the kernel, making the `root=` option mandatory.
So if the kernel commandline mangling is not appropriate just leave the
kernel commandline as it is.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Sercomm devices don't need the jffs2 cleanmarkers for the kernel
partition. With the stock firmware they are only added when the
bootloader partition is upgraded.
Furthermore, on the Sercomm H500-s, the specific cfe_jffs2_upgrade_tar
function causes OOB corruption. As a result of this, combined with the
nature of the mtdsplit driver, the upgrade procedure ends in a bricked
device.
Use the generic nand_do_upgrade provided by the OpenWrt common functions.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The uci config section network.globals set up in /bin/config_generate
will only be created if /proc/sys/net/ipv6 exists.
Correspondingly, lacking IPv6 support, the command
uci set network.globals.packet_steering=1
will fail with "uci: Invalid argument" as the network.globals config
has not been set up.
Fix that by adding the setup there as well.
While at it, limit the uci commit to the network config file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the MikroTik RouterBOARD RB493G, ported
from the ar71xx target.
See https://routerboard.com/RB493G for details
Specification:
- SoC Qualcomm Atheros AR7161
- RAM: 256 MiB
- Storage: 128MiB NAND
- Ethernet: 9x 1000/100/10 Mbps
- USB 1x 2.0 / 1.0 type A
- PCIe: 3x Mini slot
- MicroSD slot
Working:
- Board/system detection
- Ethernet
- SPI
- NAND
- LEDs
- USB
- Sysupgrade
Enabled (but untested due to lack of hardware):
- PCIe - ath79_pci_irq struct has the slot/pin/IRQ mappings if needed
Installation methods:
- tftp boot initramfs image, scp then flash via "sysupgrade -n"
- nand boot existing OpenWrt, scp then flash via "sysupgrade -n"
Notes:
- initramfs image will not work if uncompressed image size over ~8.5Mb
- The "rb4xx" drivers have been enabled
Signed-off-by: Christopher Hill <ch6574@gmail.com>
This adds 3 Mikrotik rb4xx series drivers as follows:
rb4xx-cpld: This is in the mfd subsystem, and is the parent CPLD device
that interfaces between the SoC SPI bus and its two children below.
rb4xx-gpio: This is the GPIO expander.
rb4xx-nand: This is the NAND driver.
The history of this code comes in three phases.
1. The first is a May 2015 attempt to push the equivalient ar71xx rb4xx
drivers upstream. See https://lore.kernel.org/patchwork/patch/940880/.
Module-author: Gabor Juhos <juhosg@openwrt.org>
Module-author: Imre Kaloz <kaloz@openwrt.org>
Module-author: Bert Vermeulen <bert@biot.com>
2. Next several ar71xx patches were applied bringing the code current.
commit 7bbf4117c6
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
commit af79fdbe4a
commit 889272d92d
commit e21cb649a2
commit 7c09fa4a74
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3. Finally a heavy refactor to split the driver into the three new
subsystems, and updated to work with the device tree configuration, plus
updates and review feedback incorporated
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Christopher Hill <ch6574@gmail.com>
Backport upstream patches that make drivers/spi/spi-rb4xx.c device tree
aware, plus a null pointer fix.
Signed-off-by: Christopher Hill <ch6574@gmail.com>
The Pirelli A226M-FWB has a wrong linux partition offset, caused
by a copy-paste error. As of result of this, OpenWrt is currently
broken in this unit.
Fix it.
While at it, also use generic node names and fix the addresses
there as well.
Fixes: a27d59bb42 ("brcm63xx: switch to new partition layout
specification")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[also fix/update node names, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently, ag71xx will trigger a warning when TX xor RX-Delay modes are
enabled.
Handle them identical to the already implemented RGMII modes, as they
are only different for the attached PHY.
Signed-off-by: David Bauer <mail@david-bauer.net>
The uci config section network.globals set up in /bin/config_generate
will only be created if /proc/sys/net/ipv6 exists.
Correspondingly, lacking IPv6 support, the command
uci set network.globals.packet_steering=1
will fail with "uci: Invalid argument" as the network.globals config
has not been set up.
Fix that by adding the setup there as well.
Fixes: dfd62e575c ("ramips: enable packet steering by default on mt7621")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler
Daniel González Cabanelas
Roman Yeryomin
DENG Qingfang
Yangbo Lu
Petr Štetiar
Rosen Penev
Alexey Dobrovolsky
Pawel Dembicki
John Audia
Tim Thorpe
Willem van den Akker
David Woodhouse
Sungbo Eo
Sebastian Schaper
Furkan Alaca
Sergei Burakov
Bjørn Mork
Yanase Yuki
Andrey Bondar
Sergio E. Nemirowski
Dongming Han
Emir Efe Kucuk
Thibaut VARÈNE
Davide Fioravanti
Hauke Mehrtens
David Bauer
Aleksander Jan Bajkowski
Christoph Krapp
Martin Blumenstingl
Matthew Gyurgyik
Lars Wessels
Sunguk Lee
Scott Roberts
Antti Seppälä
Leon M. George
Rowan Border
Kevin Darbyshire-Bryant
Jan Hoffmann
Alex Lewontin
Qin Wei
Rogan Dawes
Gregory L. Dietsche
Florian Eckert
Natalie Kagelmacher
Edward Matijevic
Jose Olivera
Lech Perczak
INAGAKI Hiroshi
Andrew Cameron
Hannu Nyman
Christopher Hill
