mirror of https://github.com/hak5/openwrt.git
kirkwood: add support for Check Point L-50
This patch adds support for the Check Point L-50 from 600/1100 series routers. Specification: -CPU: Marvell Kirkwood 88F6281 1200MHz -RAM: 512MB -Flash: NAND 512MB -WiFi: mPCIe card based on Atheros AR9287 b/g/n -WAN: 1 Gigabit Port (Marvell 88E1116R PHY) -LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4)) -USB: 2x USB2.0 -Express card slot -SD card slot -Serial console: RJ-45 115200 8n1 -Unsupported DSL Known issues: -DSL not supported -Expresscard not tested Installation: Step one -> backup: make backup u-boot and env for revert stock posibility make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr Step two -> Use kwboot tool to upload openwrt u-boot to RAM: run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t" end start u-boot Step three -> Restore macs (e.g. below): setenv eth1addr 00:1C:XX:XX:XX:6C setenv ethaddr 00:1C:XX:XX:XX:6B setenv lan1_mac_addr 00:1C:XX:XX:XX:6C setenv lan2_mac_addr 00:1C:XX:XX:XX:6D setenv lan3_mac_addr 00:1C:XX:XX:XX:6E setenv lan4_mac_addr 00:1C:XX:XX:XX:6F setenv lan5_mac_addr 00:1C:XX:XX:XX:70 setenv lan6_mac_addr 00:1C:XX:XX:XX:71 setenv lan7_mac_addr 00:1C:XX:XX:XX:72 setenv lan8_mac_addr 00:1C:XX:XX:XX:73 setenv dmz_mac_addr 00:1C:XX:XX:XX:74 setenv dsl_mac_addr 00:1C:XX:XX:XX:75 Step four -> flash u-boot: mw 0x0800000 0xffff 0x100000 nand erase 0x0 100000 tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb nand write 0x0800000 0x0 0x100000 saveenv Step five -> run initramfs image: tftpboot 0x02000000 openwrt.bin; bootm 0x02000000; Step six -> install sysupgrade OpenWrt image: copy to /tmp/ sysupgrade image run sysupgrade Back to stock: Restore original u-boot end env. Install factory image via stock u-boot. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>master
Pawel Dembicki
Petr Štetiar
parent
c881d7ab03
commit
67ce9aedd6
|
|
@ -13,6 +13,7 @@ touch /etc/config/ubootenv
|
|||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
checkpoint,l-50|\
|
||||
cloudengines,pogoe02|\
|
||||
cloudengines,pogoplugv4|\
|
||||
iom,ix2-200|\
|
||||
|
|
|
|||
|
|
@ -11,6 +11,9 @@ board_config_update
|
|||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
"checkpoint,l-50")
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8 dmz" "eth0"
|
||||
;;
|
||||
"cisco,on100")
|
||||
ucidef_set_interface_lan "eth0 eth1"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -0,0 +1,18 @@
|
|||
#!/bin/sh
|
||||
|
||||
. /lib/functions/uci-defaults.sh
|
||||
|
||||
board_config_update
|
||||
|
||||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
checkpoint,l-50)
|
||||
ucidef_add_gpio_switch "mpcie-rst" "mPCIE Card reset" "502" "1"
|
||||
ucidef_add_gpio_switch "exp-card-rst" "Express Card reset" "497" "1"
|
||||
;;
|
||||
esac
|
||||
|
||||
board_config_flush
|
||||
|
||||
exit 0
|
||||
|
|
@ -0,0 +1,25 @@
|
|||
. /lib/functions.sh
|
||||
. /lib/functions/system.sh
|
||||
|
||||
preinit_set_mac_address() {
|
||||
local mac
|
||||
|
||||
case $(board_name) in
|
||||
checkpoint,l-50)
|
||||
mac=$(mtd_get_mac_ascii bootldr-env lan1_mac_addr)
|
||||
|
||||
ip link set dev lan1 address $mac 2>/dev/null
|
||||
ip link set dev lan2 address $(macaddr_add $mac 1) 2>/dev/null
|
||||
ip link set dev lan3 address $(macaddr_add $mac 2) 2>/dev/null
|
||||
ip link set dev lan4 address $(macaddr_add $mac 3) 2>/dev/null
|
||||
ip link set dev lan5 address $(macaddr_add $mac 4) 2>/dev/null
|
||||
ip link set dev lan6 address $(macaddr_add $mac 5) 2>/dev/null
|
||||
ip link set dev lan7 address $(macaddr_add $mac 6) 2>/dev/null
|
||||
ip link set dev lan8 address $(macaddr_add $mac 7) 2>/dev/null
|
||||
ip link set dev dmz address $(macaddr_add $mac 8) 2>/dev/null
|
||||
ip link set dev dsl address $(macaddr_add $mac 9) 2>/dev/null
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
boot_hook_add preinit_main preinit_set_mac_address
|
||||
|
|
@ -282,6 +282,7 @@ CONFIG_PINCTRL=y
|
|||
CONFIG_PINCTRL_KIRKWOOD=y
|
||||
CONFIG_PINCTRL_MVEBU=y
|
||||
# CONFIG_PINCTRL_SINGLE is not set
|
||||
CONFIG_PINCTRL_SX150X=y
|
||||
CONFIG_PLAT_ORION=y
|
||||
CONFIG_POWER_RESET=y
|
||||
CONFIG_POWER_RESET_GPIO=y
|
||||
|
|
|
|||
|
|
@ -28,6 +28,16 @@ define Device/Default
|
|||
SUPPORTED_DEVICES = $(subst _,$(comma),$(1)) $$(BOARD_NAME)
|
||||
endef
|
||||
|
||||
define Device/checkpoint_l-50
|
||||
DEVICE_VENDOR := Check Point
|
||||
DEVICE_MODEL := L-50
|
||||
DEVICE_DTS := kirkwood-l-50
|
||||
DEVICE_PACKAGES := kmod-ath9k kmod-gpio-button-hotplug kmod-mvsdio \
|
||||
kmod-rtc-s35390a kmod-usb-ledtrig-usbport wpad-basic
|
||||
IMAGES := sysupgrade.bin
|
||||
endef
|
||||
TARGET_DEVICES += checkpoint_l-50
|
||||
|
||||
define Device/cisco_on100
|
||||
DEVICE_VENDOR := Cisco Systems
|
||||
DEVICE_MODEL := ON100
|
||||
|
|
|
|||
|
|
@ -0,0 +1,485 @@
|
|||
From efa968c18abab78c5e0c40a853caf286c3629a59 Mon Sep 17 00:00:00 2001
|
||||
From: Pawel Dembicki <paweldembicki@gmail.com>
|
||||
Date: Tue, 17 Mar 2020 21:28:01 +0100
|
||||
Subject: [PATCH v3] ARM: dts: kirkwood: Add Check Point L-50 board
|
||||
|
||||
This patch adds dts for the Check Point L-50 from 600/1100 series
|
||||
routers.
|
||||
|
||||
Specification:
|
||||
-CPU: Marvell Kirkwood 88F6821 1200MHz
|
||||
-RAM: 512MB
|
||||
-Flash: NAND 512MB
|
||||
-WiFi: mPCIe card based on Atheros AR9287 b/g/n
|
||||
-WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
|
||||
-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+3))
|
||||
-USB: 2x USB2.0
|
||||
-Express card slot
|
||||
-SD card slot
|
||||
-Serial console: RJ-45 115200 8n1
|
||||
-Unsupported DSL
|
||||
|
||||
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
|
||||
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
|
||||
---
|
||||
Changes in v3:
|
||||
- fix typo and code style issues pointed by OpenWrt guys
|
||||
Changes in v2:
|
||||
- none
|
||||
|
||||
arch/arm/boot/dts/Makefile | 1 +
|
||||
arch/arm/boot/dts/kirkwood-l-50.dts | 438 ++++++++++++++++++++++++++++
|
||||
2 files changed, 439 insertions(+)
|
||||
create mode 100644 arch/arm/boot/dts/kirkwood-l-50.dts
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -270,6 +270,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
|
||||
kirkwood-iomega_ix2_200.dtb \
|
||||
kirkwood-is2.dtb \
|
||||
kirkwood-km_kirkwood.dtb \
|
||||
+ kirkwood-l-50.dtb \
|
||||
kirkwood-laplug.dtb \
|
||||
kirkwood-linkstation-lsqvl.dtb \
|
||||
kirkwood-linkstation-lsvl.dtb \
|
||||
--- /dev/null
|
||||
+++ b/arch/arm/boot/dts/kirkwood-l-50.dts
|
||||
@@ -0,0 +1,438 @@
|
||||
+// SPDX-License-Identifier: GPL-2.0
|
||||
+/*
|
||||
+ * Check Point L-50 Board Description
|
||||
+ * Copyright 2020 Pawel Dembicki <paweldembicki@gmail.com>
|
||||
+ */
|
||||
+
|
||||
+/dts-v1/;
|
||||
+
|
||||
+#include "kirkwood.dtsi"
|
||||
+#include "kirkwood-6281.dtsi"
|
||||
+
|
||||
+/ {
|
||||
+ model = "Check Point L-50";
|
||||
+ compatible = "checkpoint,l-50", "marvell,kirkwood-88f6281", "marvell,kirkwood";
|
||||
+
|
||||
+ memory {
|
||||
+ device_type = "memory";
|
||||
+ reg = <0x00000000 0x20000000>;
|
||||
+ };
|
||||
+
|
||||
+ chosen {
|
||||
+ bootargs = "console=ttyS0,115200n8";
|
||||
+ stdout-path = &uart0;
|
||||
+ };
|
||||
+
|
||||
+ ocp@f1000000 {
|
||||
+ pinctrl: pin-controller@10000 {
|
||||
+ pinctrl-0 = <&pmx_led38 &pmx_sysrst &pmx_button29>;
|
||||
+ pinctrl-names = "default";
|
||||
+
|
||||
+ pmx_sysrst: pmx-sysrst {
|
||||
+ marvell,pins = "mpp6";
|
||||
+ marvell,function = "sysrst";
|
||||
+ };
|
||||
+
|
||||
+ pmx_button29: pmx_button29 {
|
||||
+ marvell,pins = "mpp29";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_led38: pmx_led38 {
|
||||
+ marvell,pins = "mpp38";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+
|
||||
+ pmx_sdio_cd: pmx-sdio-cd {
|
||||
+ marvell,pins = "mpp46";
|
||||
+ marvell,function = "gpio";
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ serial@12000 {
|
||||
+ status = "okay";
|
||||
+ };
|
||||
+
|
||||
+ mvsdio@90000 {
|
||||
+ status = "okay";
|
||||
+ cd-gpios = <&gpio1 14 9>;
|
||||
+ };
|
||||
+
|
||||
+ i2c@11000 {
|
||||
+ status = "okay";
|
||||
+ clock-frequency = <400000>;
|
||||
+
|
||||
+ gpio2: gpio-expander@20{
|
||||
+ #gpio-cells = <2>;
|
||||
+ #interrupt-cells = <2>;
|
||||
+ compatible = "semtech,sx1505q";
|
||||
+ reg = <0x20>;
|
||||
+
|
||||
+ gpio-controller;
|
||||
+ };
|
||||
+
|
||||
+ /* Three GPIOs from 0x21 exp. are undescribed in dts:
|
||||
+ * 1: DSL module reset (active low)
|
||||
+ * 5: mPCIE reset (active low)
|
||||
+ * 6: Express card reset (active low)
|
||||
+ */
|
||||
+ gpio3: gpio-expander@21{
|
||||
+ #gpio-cells = <2>;
|
||||
+ #interrupt-cells = <2>;
|
||||
+ compatible = "semtech,sx1505q";
|
||||
+ reg = <0x21>;
|
||||
+
|
||||
+ gpio-controller;
|
||||
+ };
|
||||
+
|
||||
+ rtc@30 {
|
||||
+ compatible = "s35390a";
|
||||
+ reg = <0x30>;
|
||||
+ };
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ leds {
|
||||
+ compatible = "gpio-leds";
|
||||
+
|
||||
+ status_green {
|
||||
+ label = "l-50:green:status";
|
||||
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
|
||||
+ };
|
||||
+
|
||||
+ status_red {
|
||||
+ label = "l-50:red:status";
|
||||
+ gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
|
||||
+ };
|
||||
+
|
||||
+ wifi {
|
||||
+ label = "l-50:green:wifi";
|
||||
+ gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
|
||||
+ linux,default-trigger = "phy0tpt";
|
||||
+ };
|
||||
+
|
||||
+ internet_green {
|
||||
+ label = "l-50:green:internet";
|
||||
+ gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
|
||||
+ };
|
||||
+
|
||||
+ internet_red {
|
||||
+ label = "l-50:red:internet";
|
||||
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
|
||||
+ };
|
||||
+
|
||||
+ usb1_green {
|
||||
+ label = "l-50:green:usb1";
|
||||
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
|
||||
+ linux,default-trigger = "usbport";
|
||||
+ trigger-sources = <&hub_port3>;
|
||||
+ };
|
||||
+
|
||||
+ usb1_red {
|
||||
+ label = "l-50:red:usb1";
|
||||
+ gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
|
||||
+ };
|
||||
+
|
||||
+ usb2_green {
|
||||
+ label = "l-50:green:usb2";
|
||||
+ gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
|
||||
+ linux,default-trigger = "usbport";
|
||||
+ trigger-sources = <&hub_port1>;
|
||||
+ };
|
||||
+
|
||||
+ usb2_red {
|
||||
+ label = "l-50:red:usb2";
|
||||
+ gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ usb2_pwr {
|
||||
+ compatible = "regulator-fixed";
|
||||
+ regulator-name = "usb2_pwr";
|
||||
+
|
||||
+ regulator-min-microvolt = <5000000>;
|
||||
+ regulator-max-microvolt = <5000000>;
|
||||
+ gpio = <&gpio3 3 GPIO_ACTIVE_LOW>;
|
||||
+ regulator-always-on;
|
||||
+ };
|
||||
+
|
||||
+ usb1_pwr {
|
||||
+ compatible = "regulator-fixed";
|
||||
+ regulator-name = "usb1_pwr";
|
||||
+
|
||||
+ regulator-min-microvolt = <5000000>;
|
||||
+ regulator-max-microvolt = <5000000>;
|
||||
+ gpio = <&gpio3 4 GPIO_ACTIVE_LOW>;
|
||||
+ regulator-always-on;
|
||||
+ };
|
||||
+
|
||||
+ mpcie_pwr {
|
||||
+ compatible = "regulator-fixed";
|
||||
+ regulator-name = "mpcie_pwr";
|
||||
+
|
||||
+ regulator-min-microvolt = <3300000>;
|
||||
+ regulator-max-microvolt = <3300000>;
|
||||
+ gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
|
||||
+ enable-active-high;
|
||||
+ regulator-always-on;
|
||||
+ };
|
||||
+
|
||||
+ express_card_pwr {
|
||||
+ compatible = "regulator-fixed";
|
||||
+ regulator-name = "express_card_pwr";
|
||||
+
|
||||
+ regulator-min-microvolt = <3300000>;
|
||||
+ regulator-max-microvolt = <3300000>;
|
||||
+ gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
|
||||
+ enable-active-high;
|
||||
+ regulator-always-on;
|
||||
+ };
|
||||
+
|
||||
+ keys {
|
||||
+ compatible = "gpio-keys";
|
||||
+
|
||||
+ factory_defaults {
|
||||
+ label = "factory_defaults";
|
||||
+ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
|
||||
+ linux,code = <KEY_RESTART>;
|
||||
+ };
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&mdio {
|
||||
+ status = "okay";
|
||||
+
|
||||
+ ethphy8: ethernet-phy@8 {
|
||||
+ reg = <0x08>;
|
||||
+ };
|
||||
+
|
||||
+ switch0: switch@10 {
|
||||
+ compatible = "marvell,mv88e6085";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+ reg = <0x10>;
|
||||
+ dsa,member = <0 0>;
|
||||
+
|
||||
+ ports {
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+
|
||||
+ port@0 {
|
||||
+ reg = <0>;
|
||||
+ label = "lan5";
|
||||
+ };
|
||||
+
|
||||
+ port@1 {
|
||||
+ reg = <1>;
|
||||
+ label = "lan1";
|
||||
+ };
|
||||
+
|
||||
+ port@2 {
|
||||
+ reg = <2>;
|
||||
+ label = "lan6";
|
||||
+ };
|
||||
+
|
||||
+ port@3 {
|
||||
+ reg = <3>;
|
||||
+ label = "lan2";
|
||||
+ };
|
||||
+
|
||||
+ port@4 {
|
||||
+ reg = <4>;
|
||||
+ label = "lan7";
|
||||
+ };
|
||||
+
|
||||
+ switch0port5: port@5 {
|
||||
+ reg = <5>;
|
||||
+ phy-mode = "rgmii-txid";
|
||||
+ link = <&switch1port5>;
|
||||
+ fixed-link {
|
||||
+ speed = <1000>;
|
||||
+ full-duplex;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ port@6 {
|
||||
+ reg = <6>;
|
||||
+ label = "cpu";
|
||||
+ phy-mode = "rgmii-id";
|
||||
+ ethernet = <ð1port>;
|
||||
+ fixed-link {
|
||||
+ speed = <1000>;
|
||||
+ full-duplex;
|
||||
+ };
|
||||
+ };
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ switch@11 {
|
||||
+ compatible = "marvell,mv88e6085";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+ reg = <0x11>;
|
||||
+ dsa,member = <0 1>;
|
||||
+
|
||||
+ ports {
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+
|
||||
+ port@0 {
|
||||
+ reg = <0>;
|
||||
+ label = "lan3";
|
||||
+ };
|
||||
+
|
||||
+ port@1 {
|
||||
+ reg = <1>;
|
||||
+ label = "lan8";
|
||||
+ };
|
||||
+
|
||||
+ port@2 {
|
||||
+ reg = <2>;
|
||||
+ label = "lan4";
|
||||
+ };
|
||||
+
|
||||
+ port@3 {
|
||||
+ reg = <3>;
|
||||
+ label = "dmz";
|
||||
+ };
|
||||
+
|
||||
+ switch1port5: port@5 {
|
||||
+ reg = <5>;
|
||||
+ phy-mode = "rgmii-txid";
|
||||
+ link = <&switch0port5>;
|
||||
+ fixed-link {
|
||||
+ speed = <1000>;
|
||||
+ full-duplex;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ port@6 {
|
||||
+ reg = <6>;
|
||||
+ label = "dsl";
|
||||
+ fixed-link {
|
||||
+ speed = <100>;
|
||||
+ full-duplex;
|
||||
+ };
|
||||
+ };
|
||||
+ };
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+ð0 {
|
||||
+ status = "okay";
|
||||
+ ethernet0-port@0 {
|
||||
+ phy-handle = <ðphy8>;
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+ð1 {
|
||||
+ status = "okay";
|
||||
+ ethernet1-port@0 {
|
||||
+ speed = <1000>;
|
||||
+ duplex = <1>;
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&nand {
|
||||
+ status = "okay";
|
||||
+ pinctrl-0 = <&pmx_nand>;
|
||||
+ pinctrl-names = "default";
|
||||
+
|
||||
+ partition@0 {
|
||||
+ label = "u-boot";
|
||||
+ reg = <0x00000000 0x000c0000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@a0000 {
|
||||
+ label = "bootldr-env";
|
||||
+ reg = <0x000c0000 0x00040000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@100000 {
|
||||
+ label = "kernel-1";
|
||||
+ reg = <0x00100000 0x00800000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@900000 {
|
||||
+ label = "rootfs-1";
|
||||
+ reg = <0x00900000 0x07100000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@7a00000 {
|
||||
+ label = "kernel-2";
|
||||
+ reg = <0x07a00000 0x00800000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@8200000 {
|
||||
+ label = "rootfs-2";
|
||||
+ reg = <0x08200000 0x07100000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@f300000 {
|
||||
+ label = "default_sw";
|
||||
+ reg = <0x0f300000 0x07900000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@16c00000 {
|
||||
+ label = "logs";
|
||||
+ reg = <0x16c00000 0x01800000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@18400000 {
|
||||
+ label = "preset_cfg";
|
||||
+ reg = <0x18400000 0x00100000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@18500000 {
|
||||
+ label = "adsl";
|
||||
+ reg = <0x18500000 0x00100000>;
|
||||
+ };
|
||||
+
|
||||
+ partition@18600000 {
|
||||
+ label = "storage";
|
||||
+ reg = <0x18600000 0x07a00000>;
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&rtc {
|
||||
+ status = "disabled";
|
||||
+};
|
||||
+
|
||||
+&pciec {
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&pcie0 {
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&sata_phy0 {
|
||||
+ status = "disabled";
|
||||
+};
|
||||
+
|
||||
+&sata_phy1 {
|
||||
+ status = "disabled";
|
||||
+};
|
||||
+
|
||||
+&usb0 {
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+ status = "okay";
|
||||
+
|
||||
+ port@1 {
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+ reg = <1>;
|
||||
+ #trigger-source-cells = <0>;
|
||||
+
|
||||
+ hub_port1: port@1 {
|
||||
+ reg = <1>;
|
||||
+ #trigger-source-cells = <0>;
|
||||
+ };
|
||||
+
|
||||
+ hub_port3: port@3 {
|
||||
+ reg = <3>;
|
||||
+ #trigger-source-cells = <0>;
|
||||
+ };
|
||||
+ };
|
||||
+};
|
||||
|
|
@ -0,0 +1,47 @@
|
|||
--- a/arch/arm/boot/dts/kirkwood-l-50.dts
|
||||
+++ b/arch/arm/boot/dts/kirkwood-l-50.dts
|
||||
@@ -18,6 +18,13 @@
|
||||
reg = <0x00000000 0x20000000>;
|
||||
};
|
||||
|
||||
+ aliases {
|
||||
+ led-boot = &led_status_green;
|
||||
+ led-failsafe = &led_status_red;
|
||||
+ led-running = &led_status_green;
|
||||
+ led-upgrade = &led_status_red;
|
||||
+ };
|
||||
+
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
stdout-path = &uart0;
|
||||
@@ -95,12 +102,12 @@
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
- status_green {
|
||||
+ led_status_green: status_green {
|
||||
label = "l-50:green:status";
|
||||
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
- status_red {
|
||||
+ led_status_red: status_red {
|
||||
label = "l-50:red:status";
|
||||
gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
@@ -349,13 +356,8 @@
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
- label = "kernel-1";
|
||||
- reg = <0x00100000 0x00800000>;
|
||||
- };
|
||||
-
|
||||
- partition@900000 {
|
||||
- label = "rootfs-1";
|
||||
- reg = <0x00900000 0x07100000>;
|
||||
+ label = "ubi";
|
||||
+ reg = <0x00100000 0x07900000>;
|
||||
};
|
||||
|
||||
partition@7a00000 {
|
||||
Loading…
Reference in New Issue