Kernel 3.14 introduced a switch reset in phy_init_hw in drivers/net/phy
causing BMCR_ANENABLE to get cleared.
Due to the fact that ar8xxx_phy_config_aneg does nothing for
PHY 0 autonegatiation support remains disabled.
This can cause ports to operate at 10MBit/half-duplex only.
Fix this by calling genphy_config_aneg for PHY 0 too as
genphy_config_aneg sets BMCR_ANENABLE if it's not yet set.
Fixes: ticket 17800
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43332 3c298f89-4303-0410-b956-a3cf2f4a3e73
PHY init code in the switch-specific hw_init functions is mainly
identical. Factor it out into a generic ar8xxx_phy_init function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43331 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move phy fixup code from the chip-specific hw_init functions into a
fixup_phys callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43330 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently there is a fixed 1000ms wait time after the switch was reset.
Most if not all switches need much less time to perform a reset.
Therefore replace the fixed wait time with polling for BMCR_RESET to
be cleared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43329 3c298f89-4303-0410-b956-a3cf2f4a3e73
All supported switches have 5 PHYs. Currently partially 5 is hardcoded
and partially switch-specific constants exist.
Replace them with a global constant.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43328 3c298f89-4303-0410-b956-a3cf2f4a3e73
wg302v1_fixup() looks for the ATAG_CMDLINE atag, it doesn't find it and
so it takes the last atag in the list and overwrites non allocated
memory.
The side effects are corrupted vital data and a kernel that doesn't
boot. More details here https://dev.openwrt.org/ticket/18356
The fix appends the fixup to the command line and updates the atag only
when it finds it.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43320 3c298f89-4303-0410-b956-a3cf2f4a3e73
Few notes:
- redboot partitions are unusable
- redboot declares only 16M of RAM, hence the mem arg in cmdline and separate kernel config
- boots fine but only ethernet works for now
- split wiliboard and raidsonic boards into different subtargets
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43319 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds 3.14 kernel support for the mpc85xx platform.
Works fine here with a TL-WDR4900 which seems to be the only
supported device using this platform.
There might be differences depending on HW version, therefore
I'd ask others to test too.
Changes to 3.10
missing config options added to 3.14 config file
patch 001: rebased
patch 100: rebased
patch 110: rebased
patch 120: rebased
patch 130: rebased
patch 140: minor adjustment
patch 200: removed, change went upstream
patch 210: rebased
patch 220: removed, change went upstream
patch 750: new, fixes an issue with ethernet port autoneg being
disabled due to changes in kernel phy handling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43308 3c298f89-4303-0410-b956-a3cf2f4a3e73
still no sound but the codec is properly detected now, powers up and i can hear
noise on the speakers.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43305 3c298f89-4303-0410-b956-a3cf2f4a3e73
hardware status and tx vlan offload support on all targets
except rt5350. so i modify the IS_ENABLE condition only for
mt7621.
support mt7621 hardware status reference by SDK. but i don't
have mt7621. if not work just set mt7621 FE_REG_FE_COUNTER_BASE
to 0 to let software count.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43303 3c298f89-4303-0410-b956-a3cf2f4a3e73
hardware tx vlan offload only support max 16 vids
now use add/delete vlan interface to update vlan id table
when duplicate vlan id index detect.
disable hardware tx vlan offload support.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43301 3c298f89-4303-0410-b956-a3cf2f4a3e73
sdhci failed to init because of this
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43293 3c298f89-4303-0410-b956-a3cf2f4a3e73
some old mt7620a uboots dont reset the pcie core properly. work around this
issue in the kernel driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43292 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without this patch the UBIFS driver is unable to attach to the mtd
storage and mount the root FS.
Fixes a kernel panic with Netgear WNDR4300/3700v4 devices.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43287 3c298f89-4303-0410-b956-a3cf2f4a3e73
Sets the system LED on the EasyLink M150 and mini to lower-case "easylink"
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43271 3c298f89-4303-0410-b956-a3cf2f4a3e73
this makes gpio-poweroff work
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43254 3c298f89-4303-0410-b956-a3cf2f4a3e73
the new driver handles newer SoCs
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43250 3c298f89-4303-0410-b956-a3cf2f4a3e73
a missing "val =" caused the AN bit in the phy0 reg to be flushed.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43246 3c298f89-4303-0410-b956-a3cf2f4a3e73
the SDK does a bit of extra init that we did not do yet when using an external mt7530.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43245 3c298f89-4303-0410-b956-a3cf2f4a3e73
somehow all switch ports still come up as 10mbit.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43237 3c298f89-4303-0410-b956-a3cf2f4a3e73
make 1166 wan port work. this broke due to the esw_polling bug
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43236 3c298f89-4303-0410-b956-a3cf2f4a3e73
this driver confuses some boards
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43234 3c298f89-4303-0410-b956-a3cf2f4a3e73
Camera has microphone; in order to use it by default enable sound support.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43232 3c298f89-4303-0410-b956-a3cf2f4a3e73
* read MAC address from factory partition
* remove port defines since there is only one port (most likely C/P error)
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43231 3c298f89-4303-0410-b956-a3cf2f4a3e73
i accidentally dropped 2 lines while adding mt7628 support
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43216 3c298f89-4303-0410-b956-a3cf2f4a3e73
r43200 tries to detect if the fixup is needed or not. control the behaviour via
OF instead and disable unused ports.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43201 3c298f89-4303-0410-b956-a3cf2f4a3e73
this broke e1700 lan2 as the fixup was applied to the phy inside the mt7530.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43200 3c298f89-4303-0410-b956-a3cf2f4a3e73
the current driver code wont know which mt7530 to apply the llllw setting to.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43199 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite <leitec@staticky.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43153 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add patches for getting the IRQ number for a device of the bcma bus
that were send for upstream inclusion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43148 3c298f89-4303-0410-b956-a3cf2f4a3e73
This makes it possible to activate early printk.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43145 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds a kernel config for kernel 3.18
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43140 3c298f89-4303-0410-b956-a3cf2f4a3e73
The patch adding AR8216_PHY_LEDS was not ported to more recent kernel
versions.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43139 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some changes from the header file were not ported from older kernel.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43137 3c298f89-4303-0410-b956-a3cf2f4a3e73
The select SYS_HAS_DMA_OPS in CPU_CAVIUM_OCTEON was from the kernel
patch in 3.13, but it is only included in kernel 3.14 and not in 3.13
and 3.18, add it again.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43134 3c298f89-4303-0410-b956-a3cf2f4a3e73
Apply patch for kernel 3.10 from r43112 also in 3.12, 3.14 and 3.18.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43133 3c298f89-4303-0410-b956-a3cf2f4a3e73
this caused a crash on boot
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43120 3c298f89-4303-0410-b956-a3cf2f4a3e73
some bootloaders (linksys e1700) set wonky hw trap values. reset this upon boot to make all ports work.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43117 3c298f89-4303-0410-b956-a3cf2f4a3e73
latest mt7530 silicon seems to have a different phy id.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43113 3c298f89-4303-0410-b956-a3cf2f4a3e73
OpenWRT patch 255-lib80211_kconfig_hacks gives user possiblity to select
LIB80211 dependant settings (LIB80211_CRYPT_*) without having LIB80211
selected which is wrong.
My patch changes OpenWRT patch so LIB80211 is vissible and all
LIB80211_CRYPT_* options selects LIB80211 automatically.
Signed-off-by: Tomasz Wasiak <tjwasiak@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43112 3c298f89-4303-0410-b956-a3cf2f4a3e73
Change list:
* add tx scatter gather function.
* add software rx vlan offload to let GRO work.
* add jumbo frame support. because use build_skb so max MTU is 3812.
* enable hardware tx vlan.
* enable GRO and remove LRO. because it can improve performance and can work on forwarding.
* enable/fix tx padding function.
* let napi handle tx clean up.
* support ethtool operation. now support message level, hardware status and coalesce.
* ethtool support use mdio to get phy status only on mt7620. need modify dts file and add phy info to support it.
Notes:
* build and test on rt2880, rt3052, rt3352, rt3662, rt5350 and mt7620a.
* TCP NAT performance improve. test with netperf.
- rt2880(gigabit) from 5x to 12x Mbps.
- rt3x5x from 6x to 94 Mbps.
- rt5250 from 5x to 8x Mbps.
- rt3662(gigabit) from 6x to 42x Mbps with GRO. 23x Mbps without GRO. 66x Mbps with jumbo frame.
- mt7620 still 94Mbps.
* TSO function not tested. because i don't have mt7620 with eco >= 5. and the hardware don't support to set MSS. it will have problem.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43108 3c298f89-4303-0410-b956-a3cf2f4a3e73
Boards that have more than one swconfig enabled switch will show the devices in
reverse order when call swconfig list. Fix this by using list_add_tail().
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43106 3c298f89-4303-0410-b956-a3cf2f4a3e73
0x8100000c vs 0x810000c0 int he pvc register this caused the cascade with an external mt7530 to fail.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43104 3c298f89-4303-0410-b956-a3cf2f4a3e73
(Reposted due to an issue with the patchwork server during original submission)
Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)
Signed-off-by: Gareth Bryan <gareth@mx9.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43102 3c298f89-4303-0410-b956-a3cf2f4a3e73
lantiq_dsl.sh didn't work with VDSL chipsets for now, fix that by
detecting whether vdsl_cpe_control or dsl_cpe_control should be used.
Also add missing quotes around shell string comparision.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43101 3c298f89-4303-0410-b956-a3cf2f4a3e73
This SoC does not have a vfpv3 FPU.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43098 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds initial support for kernel 3.18.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43097 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are still many options missing.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43096 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch 060 we had in repo was never sent/accepted.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43091 3c298f89-4303-0410-b956-a3cf2f4a3e73
This works around a bootloader issue where every device
has the same lan/wan-mac 00:04:9f:ef:01:01 - with this patch
we read the macs from config-partition during initial network
setup. We have 9 valid macs stored in the partition, the
1st two are used for the radios, 3 and 4 are now used for WAN/LAN.
on an already setup / running device we can get the real macs with
. /lib/functions.sh
. /lib/functions/system.sh
echo "LAN = $(mtd_get_mac_binary config 338)"
echo "WAN = $(mtd_get_mac_binary config 344)"
see:
https://dev.openwrt.org/ticket/14714
from the ticket / user klondike:
U-Boot passed this commit ecd1a09b81http://u-boot.10912.n7.nabble.com/U-Boot-PATCH-mpc83xx-remove-hardcoded-network-addresses-from-config-files-td44372.html
I suppose to prevent this particular issue, but the WDR4900 may be using an old bootloader still affected.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
I have been checking the contents of the dtb on the flash, this particular bit is quite revealing:
ethernet@b0000 {
#address-cells = <0x1>;
#size-cells = <0x1>;
device_type = "network";
model = "eTSEC";
compatible = "fsl,etsec2";
fsl,num_rx_queues = <0x8>;
fsl,num_tx_queues = <0x8>;
local-mac-address = [00 00 00 00 00 00];
^^^^^^^^^^^^^^^^^
interrupt-parent = <0x2>;
phy-handle = <0x3>;
phy-connection-type = "rgmii-id";
ptimer-handle = <0x4>;
queue-group@0 {
#address-cells = <0x1>;
#size-cells = <0x1>;
reg = <0xb0000 0x1000>;
rx-bit-map = <0xff>;
tx-bit-map = <0xff>;
interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
};
};
I also have been checking the live device map to find this:
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b0000/local-mac-address
00000000 00 04 9f ef 01 01 |......|
00000006
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b1000/local-mac-address
*
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b2000/local-mac-address
*
My conclussion is that U-Boot most likely finds the device and (as no valid MAC-address is provided)
falls back to the default MAC provided by the old code, the kernel then receives thee modified
device map from U-Boot and assumes this is the correct MAC for the device despite it obviously isn't.
This can be seen at
target/linux/mpc85xx/patches-3.10/140-powerpc-85xx-tl-wdr4900-v1-support.patch
The enetaddr is filled up by using the device tree data by the process_boot_dtb
function and used by the platform_fixups function to set the eth0 address
(by calling dt_fixup_mac_address_by_alias("ethernet0", enetaddr); ).
But instead we should be used the device address which to my understanding is
provided in the mtd.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43074 3c298f89-4303-0410-b956-a3cf2f4a3e73
The existance of this new board has been confirmed and tested by the guy on this commit
76fdd8e638
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43072 3c298f89-4303-0410-b956-a3cf2f4a3e73
All platforms which are using 3.10.x at the moment are upgraded.
Changelogs:
https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.50https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.51https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.52https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.53https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.54https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.55https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.56https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.57https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.58
A new symbol 'X86_16BIT' appeared in 3.10.52 with commit 34273f41d57ee8d854dcd2a1d754cbb546cb548f
("x86-espfix-make-it-possible-to-disable-16-bit-support.patch")
I defaults to 'unset', but it's worth a discussion to enable it
("turn off support for any 16-bit software").
Also removed the patch 0db3db45f5bd6df4bdc03bbd5dec672e16164c4e
("fix build failure on memcpy() in decompress.c")
and is obsolete by commit 29593fd5a8149462ed6fad0d522234facdaee6c8 upstream.
included in kernel 3.10.56
compile tested on all platforms with:
make tools/install
make toolchain/install
make target/linux/compile
user@box:~/user/openwrt$ cat /tmp/log.txt
[Wed Oct 22 00:36:02 CEST 2014] ./smoketest.sh: ar71xx - OK
[Wed Oct 22 00:53:22 CEST 2014] ./smoketest.sh: ar7 - OK
[Wed Oct 22 01:08:27 CEST 2014] ./smoketest.sh: au1000 - OK
[Wed Oct 22 01:21:43 CEST 2014] ./smoketest.sh: avr32 - OK
[Wed Oct 22 01:37:47 CEST 2014] ./smoketest.sh: cns21xx - OK
[Wed Oct 22 01:52:05 CEST 2014] ./smoketest.sh: cns3xxx - OK
[Wed Oct 22 02:10:23 CEST 2014] ./smoketest.sh: gemini - OK
[Wed Oct 22 02:29:07 CEST 2014] ./smoketest.sh: ixp4xx - OK
[Wed Oct 22 02:44:01 CEST 2014] ./smoketest.sh: malta - OK
[Wed Oct 22 02:55:57 CEST 2014] ./smoketest.sh: mpc85xx - OK
[Wed Oct 22 03:07:56 CEST 2014] ./smoketest.sh: orion - OK
[Wed Oct 22 03:24:30 CEST 2014] ./smoketest.sh: ppc40x - OK
[Wed Oct 22 03:40:19 CEST 2014] ./smoketest.sh: ppc44x - OK
[Wed Oct 22 03:55:29 CEST 2014] ./smoketest.sh: realview - OK
[Wed Oct 22 04:09:47 CEST 2014] ./smoketest.sh: sparc - OK
[Wed Oct 22 04:23:37 CEST 2014] ./smoketest.sh: x86 - OK
[Wed Oct 22 04:35:56 CEST 2014] ./smoketest.sh: xburst - OK
run tested on x86, au1000, ar71xx, mpc85xx and brcm47xx
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43049 3c298f89-4303-0410-b956-a3cf2f4a3e73
replace all occurences of LINUX_VERSION with the cleaner
approach. future kernel upgrades must mostly touch only
one file. the only platform left is netlogic, because it
uses a intermediate kernel 3.14.16
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43047 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for Broadcom/Netlogic XLR/XLP support
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43037 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is required due to 306-mips_mem_functions_performance.patch, just
add a memmove() implementation to satisfy the lzma2 decompressor code.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43036 3c298f89-4303-0410-b956-a3cf2f4a3e73
According to the ticket #18152 it also uses NAND with 0x20000 erase size
and 0x800 page size.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43008 3c298f89-4303-0410-b956-a3cf2f4a3e73
SENSORS_VEXPRESS is masked by HWMON
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42984 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix sysupgrade to determine the correct boot block device to use if
/proc/cmdline contains a PARTUUID root.
Change the preinit move_config() hook to use the UUID scanning code
from sysupgrade in order to avoid code duplication.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42968 3c298f89-4303-0410-b956-a3cf2f4a3e73
Enable the required squashfs and block2mtd support in the kernel in order
to be able to actually boot them.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42967 3c298f89-4303-0410-b956-a3cf2f4a3e73
If the underlying block device is a USB device it might require some
time to settle, observed when booting a squashfs image from sd card
on an Alix APU board.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42966 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix the move_config() procedure to properly find the corresponding disk if
the rootfs was mounted by PARTUUID instead of a device node.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42946 3c298f89-4303-0410-b956-a3cf2f4a3e73
This kmod is required by the Alix APU 1D4 to be reachable after
installing an x86-64 image.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42945 3c298f89-4303-0410-b956-a3cf2f4a3e73
We still don't have a smart sysupgrade method, but at least we can use
UBI which provides some protection for rootfs (SquashFS).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42941 3c298f89-4303-0410-b956-a3cf2f4a3e73
UBI requires PEBs to be formatted (with a valid UBI header) or empty
(0xFF), however CFE doesn't clear blocks after flashing the image. To
workaround this problem, teach UBI to recognize EOF mark in a similar
way JFFS2 handles that in OpenWrt.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42940 3c298f89-4303-0410-b956-a3cf2f4a3e73
This could be used on NAND devices once we get UBI working.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42938 3c298f89-4303-0410-b956-a3cf2f4a3e73
This will allow us to add proper support for NAND one day.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42937 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change configures grub to mount the rootfs by PARTUUID instead of the
device path if CONFIG_TARGET_ROOTFS_PARTNAME is unset.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42936 3c298f89-4303-0410-b956-a3cf2f4a3e73
- Add current buildroot scm url as base feed to feeds.conf
- Prefer feeds.conf over feeds.conf.default when generating the SDK feeds.conf.default
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42935 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.
Signed-off-by: Josef Gajdusek <atx@atx.name>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42922 3c298f89-4303-0410-b956-a3cf2f4a3e73
The installation process on nand-based boards using ubi
like the BTHOMEHUBV2B makes use of a ramdisk image, so it
makes sense to generate this by default.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42920 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently JFFS2 end-of-filesystem marker 0xdeadc0de is included the
computation of image's MD5 checksum as part of the seama header. But
OpenWrt will erase blocks including and after the marker thus
invalidating the checksum after the first boot.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42915 3c298f89-4303-0410-b956-a3cf2f4a3e73
Qihoo C301 has 2 flash chips of which one is used as primary and the
other is used as backup. OEM U-Boot will try to boot an activeregion N
with imageNstatus=0 and imageNtrynum <= imagemaxtry. If such a region
is found, bootloader will try to increment imageNtrynum and boot it.
This patch tries to reset imageNtrynum after each successful boot (if
the boot process reaches the execution of /etc/init.d/done).
root@OpenWrt:/# hexdump -C -n 128 /dev/mtdblock9
00000000 9e f3 63 91 61 63 74 69 76 65 72 65 67 69 6f 6e |..c.activeregion|
00000010 3d 31 00 69 6d 61 67 65 31 73 74 61 74 75 73 3d |=1.image1status=|
00000020 30 00 69 6d 61 67 65 32 73 74 61 74 75 73 3d 30 |0.image2status=0|
00000030 00 69 6d 61 67 65 32 74 72 79 6e 75 6d 3d 30 00 |.image2trynum=0.|
00000040 69 6d 61 67 65 6d 61 78 74 72 79 3d 33 00 69 6d |imagemaxtry=3.im|
00000050 61 67 65 31 74 72 79 6e 75 6d 3d 30 00 00 00 00 |age1trynum=0....|
00000060 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42914 3c298f89-4303-0410-b956-a3cf2f4a3e73
Change the "help" info to emphasize that this option refers
specifically to packaging the toolchain that would be built anyway.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42912 3c298f89-4303-0410-b956-a3cf2f4a3e73
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42911 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42897 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change makes the profile of WDR4900 more consistent with other router
specific profiles.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42896 3c298f89-4303-0410-b956-a3cf2f4a3e73
This way we will get logs if case of hang/crash in bcma or related code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42894 3c298f89-4303-0410-b956-a3cf2f4a3e73
Error reported by buildbot:
Package kmod-at91-adc is missing dependencies for the following libraries:
input-core.ko
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42893 3c298f89-4303-0410-b956-a3cf2f4a3e73
7Links PX-4885 (clones) can also be purchased with 8MB flash.
Creating images for these routers, use dtsi for common part
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42892 3c298f89-4303-0410-b956-a3cf2f4a3e73
DT file doesn't include any GPIOs yet, but let's add it as we got some
interest in this device on IRC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42864 3c298f89-4303-0410-b956-a3cf2f4a3e73
Let's generate a simple TRX file as we can't get encrypted one.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42863 3c298f89-4303-0410-b956-a3cf2f4a3e73
This allows IPv6 to set up without IPv4 being up thus
IPv6-only or IPv6+DS-Lite working with the default config.
Signed-off-by: Steven Barth <steven@midlink.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42848 3c298f89-4303-0410-b956-a3cf2f4a3e73
Have gpio driver adopt irqdomain support so that there are
non-overlapping allocations of irq numbers mapped to gpio's.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42844 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch originally failed to combine INTA/B/C/D onto a single ARM CPU
interrupt. Instead, it mapped INTA/B/C and excluded D. This patch
corrects the issue by mapping all four interrupts to the single ARM CPU
interrupt. The original intent of the patch still holds as the newer PCB
take advantage of isolated interrupts. This fix only applies to older
PCB's that do not route INTA/B/C/D to unique external ARM CPU
interrupts.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42830 3c298f89-4303-0410-b956-a3cf2f4a3e73
Felix Fietkau
Rafał Miłecki
John Crispin
Luka Perkov
Hauke Mehrtens
Nicolas Thill
Imre Kaloz
Steven Barth
Zoltan HERPAI
Florian Fainelli
Jo-Philipp Wich