c0f6c75cf7
brcm47xx: if the cpuport of the switch is port 8 assume vlan0ports: "1 2 3 4 8" and vlan0ports: "0 8"
...
SVN-Revision: 35597
2013-02-14 12:38:16 +00:00
243c582213
switch: export name of device found via /proc
...
SVN-Revision: 35596
2013-02-14 12:36:52 +00:00
60913bbac6
switch: export cpuport, ports and vlans via /proc
...
SVN-Revision: 35595
2013-02-14 12:36:13 +00:00
c75c1e03a3
firmware-utils/mktplinkfw: add support for the TL-WDR4900 v1
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35593
2013-02-13 16:51:24 +00:00
9d86ba2ed4
mpc85xx: enable swconfig and the ar8216 driver
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35592
2013-02-13 16:51:23 +00:00
6d18518e02
mpc85xx: enable the squashfs driver
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35591
2013-02-13 16:51:21 +00:00
c3b3f77621
mpc85xx: enable XZ_DEC_BCJ and XZ_DEC_POWERPC support
...
Squashfs is unable to decompress some blocks without that:
[ 199.494500] SQUASHFS error: xz_dec_run error, data probably corrupt
[ 199.500910] SQUASHFS error: squashfs_read_data failed to read block 0xbff26
[ 199.508016] SQUASHFS error: Unable to read data cache entry [bff26]
[ 199.514440] SQUASHFS error: Unable to read page, block bff26, size 153f8
[ 199.521311] SQUASHFS error: Unable to read data cache entry [bff26]
[ 199.527724] SQUASHFS error: Unable to read page, block bff26, size 153f8
[ 199.534594] SQUASHFS error: Unable to read data cache entry [bff26]
[ 199.541009] SQUASHFS error: Unable to read page, block bff26, size 153f8
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35590
2013-02-13 16:51:19 +00:00
7484006498
ar71xx: fix factory image creation for dir-825-c1
...
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35589
2013-02-13 16:36:26 +00:00
5f10ec3c36
ar71xx: fix switch-config for dir-825-c1
...
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35588
2013-02-13 16:36:23 +00:00
54ca3eed5d
brcm47xx: configure vlan correctly on some recent devices.
...
SVN-Revision: 35587
2013-02-13 16:05:52 +00:00
17c18e23ab
switch: add support for BCM53125
...
SVN-Revision: 35586
2013-02-13 16:05:32 +00:00
446414f367
switch: resetting and enabling vlan write for gigabit switches
...
This patch makes it possible to reset and enable writing vlans to recent switchs.
This is based on a patch by jcharest and the Broadcom SDK.
SVN-Revision: 35585
2013-02-13 16:05:13 +00:00
43b4f67f25
switch: read and write vlan config from and to gigabit switches
...
This patch makes it possible to read and write the vlan config from and to recent switchs.
This is based on a patch by jcharest and the Broadcom SDK.
SVN-Revision: 35584
2013-02-13 16:04:50 +00:00
8ab78d1096
switch: improve robo_switch_enable()
...
This is based on a patch by jcharest and the Broadcom SDK.
SVN-Revision: 35583
2013-02-13 16:04:18 +00:00
b8a84038a5
switch: fix switches with more than 6 ports
...
This is based on a patch by jcharest and the Broadcom SDK.
SVN-Revision: 35582
2013-02-13 16:03:47 +00:00
3c51948454
switch: reverse if else in handle_vlan_port_read()
...
SVN-Revision: 35581
2013-02-13 16:03:27 +00:00
9d3b0f5661
switch: the BCM5365 is a special switch and the BCM5350 or BCM5325 is the normal case.
...
This makes it easier to compare this code with the code from the Broadcom SDK.
SVN-Revision: 35580
2013-02-13 16:03:03 +00:00
827e315017
switch: reset switch before using it.
...
SVN-Revision: 35579
2013-02-13 16:02:41 +00:00
f3360fdf67
switch: improve error handling in robo_probe()
...
SVN-Revision: 35578
2013-02-13 16:02:20 +00:00
3f0c0c6935
switch: run cleanfile over the source code
...
SVN-Revision: 35577
2013-02-13 16:01:50 +00:00
31718416e6
mac80211: add some small fixes for minstrel_ht CCK support
...
SVN-Revision: 35576
2013-02-13 09:53:28 +00:00
4663d424a3
brcm47xx: add some more fixes to bgmac
...
Thank you Rafał Miłecki and Nathan Hintz
SVN-Revision: 35574
2013-02-12 20:10:38 +00:00
7c0208b336
brcm47xx: update tg3 to the version send upstream
...
SVN-Revision: 35573
2013-02-12 20:09:15 +00:00
7973ef64d6
mvebu: remove boards suffix
...
SVN-Revision: 35572
2013-02-12 10:18:53 +00:00
bae4bfe3f8
kernel: update linux 3.7 to 3.7.7
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35571
2013-02-12 09:51:11 +00:00
99b69fd9c5
odhcp6c: allow setting a user-provided prefix as well
...
SVN-Revision: 35570
2013-02-12 08:23:54 +00:00
eeaf2c0b5a
iptables: fix bad PKG_RELEASE in previous commit
...
SVN-Revision: 35569
2013-02-11 22:14:38 +00:00
916902b1d2
iptables: add --lenient switch to iptables-restore and ip6tables-restore that allows to skip erroneous lines
...
SVN-Revision: 35568
2013-02-11 21:58:42 +00:00
1f9ede9cfc
ar71xx: add script for automatic switch name migration
...
Thanks to Jonas Gorski for the help.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35567
2013-02-11 21:41:16 +00:00
0564b6beef
mac80211: add CCK rate support to minstrel_ht to improve range
...
SVN-Revision: 35566
2013-02-11 18:59:14 +00:00
1810b80ec0
mac80211/hostapd: short_preamble is a per-vif option and should be enabled by default
...
SVN-Revision: 35565
2013-02-11 18:59:10 +00:00
2e7a4b088d
ar71xx: allow unknown multicast frames to pass to the CPU on AR934x
...
SVN-Revision: 35564
2013-02-11 18:59:05 +00:00
9525a075c1
ar8216: remove superfluous code from ar8216_config_init
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35562
2013-02-11 16:57:31 +00:00
94806a13af
ar71xx: use switchX names in network configuration
...
Accessing the AR8xxx switches via the name of the
attached ethernet device is not possible since
r35560. Change the uci-defaults script to use
switchX names in switch configurations.
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35561
2013-02-11 16:54:52 +00:00
9c86d268eb
generic: ar8216: don't use ethernet device name in register_switch
...
The switches are accessed via an MDIO bus. Set the alias
to the name of the MDIO bus, and show that in the message
along with the name of the switch switch device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35560
2013-02-11 16:11:31 +00:00
3f3eba88f6
generic: ar8216: reuse the private data from ar8216_probe
...
The private data of the switch is already
allocated in ar8216_priv, assign that to
each PHY on the same MDIO bus. Also remove
the redundant code from ar8216_config_init.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35559
2013-02-11 16:11:30 +00:00
1afb759b35
generic: ar8216: use phydev instead of pdev everywhere
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35555
2013-02-11 13:25:43 +00:00
0b1fe07e8e
generic: ar8216: use pr_* macros for kernel messages
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35554
2013-02-11 13:14:00 +00:00
b8c796fbd7
odhcp6c: Various bugfixes * Don't send undesired suggestions for preferred and valid lifetimes * Be less verbose in logging
...
SVN-Revision: 35553
2013-02-11 12:30:16 +00:00
eea297884e
generic: ar8216: fix PHY features setup
...
Sujith says:
This commit breaks the WAN port on my AP96 - DHCP fails.
Reverting it fixes the issue.
commit b67cc3a0cdd02973610d4d5a63226d1c44841e94
Author: juhosg <juhosg@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Fri Feb 8 09:13:18 2013 +0000
generic: ar8216: simplify phy features setup
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@355183c298f89-4303-0410-b956-a3cf2f4a3e73
This change restores the previous behaviour and moves
the code into the ar8216_probe function.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
SVN-Revision: 35549
2013-02-11 10:05:35 +00:00
617076c613
generic: ar8216: add ar8xxx_probe_switch helper
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35547
2013-02-10 19:02:01 +00:00
98b13e39ac
generic: ar8216: rename ar8xxx_mib_cleanup to ar8xxx_mib_stop
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35546
2013-02-10 18:42:08 +00:00
f97170a720
generic: ar8216: free mib counters from ar8xxx_free
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35545
2013-02-10 18:42:07 +00:00
7924e517af
generic: ar8216: add ar8xxx_free helper
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35544
2013-02-10 18:42:05 +00:00
77b3c551c4
generic: ar8216: add ar8xxx_create{,mii} helpers
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35543
2013-02-10 18:42:04 +00:00
5f70b1db2a
generic: ar8216: remove redundant phy address check
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35542
2013-02-10 18:38:12 +00:00
14fd37258b
generic: ar8216: only set phy_ptr if packet mangling is used
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35541
2013-02-10 18:38:10 +00:00
393163b098
generic: ar8216: add defines for the AR8316 POSTRIP register
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35539
2013-02-10 13:18:48 +00:00
5ed480598d
generic: ar8216: don't probe the chip multiple times
...
It is only needed when the private data is allocated.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35538
2013-02-10 13:05:15 +00:00
774da6c7a4
generic: ar8216: add sanity check to ar8216_probe
...
Verify that the mdio bus has PHY devices with
a supported PHY ID at address 0-4.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35537
2013-02-10 13:05:14 +00:00
Hauke Mehrtens
Gabor Juhos
Felix Fietkau
Luka Perkov
Steven Barth
Jo-Philipp Wich