- all uci rules are boxed in custom chains now, so a firewall stop leaves user rules intact
- properly handle selective ipv4 or ipv6 only firewall start/stop/restart actions
- support ip ranges (e.g. option src_ip '!192.168.1.1-192.168.1.100' -> -m iprange ! --src-range 192.168.1.1-192.168.1.100')
- support time options (e.g. option weekdays 'Mon Tue Sat' -> -m time --weekdays 1,2,6')
SVN-Revision: 35738
Use the same MAC addresses as the original firmware.
Based on a patch from #10421.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Tested-by: Gabor Varga <vargagab@gmail.com>
SVN-Revision: 35730
This builds and boots.
Because of the function pointer indirection (e.g. mtd_info's read
function pointer is assigned to spiflash_read), it is difficult for me
to understand where the calls are coming from (could be anywhere,
conditionally pointing at spiflash versions), so I punted and used the
renamed function pointers (_erase, _read, _write). If someone knows
better what to do, please fix.
Cleaned up other sundry kernel tracking issues like get_phy_id and
__devinit,etc.
[juhosg: don't switch to that yet]
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35727
Setting this bit stops BCM53125 (bgmac actually) from receiving any
packets. This bit is cleared conditionally in b53_switch_reset and it
seems the same is done in bcmrobo.c which never sets that bit again.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 35723
They either work around missing implementations in uClibc 0.9.30 and
earlier and add already present functionality.
Closes#11210, #11211.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35710
PTP for gianfar can be built as a module. Create a package for it.
[juhosg: remove the mp85xx specific patch]
Patchwork: http://patchwork.openwrt.org/patch/3344/
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35706
[juhosg: move the fsl-pq-mdio driver into a separate package]
Patchwork: http://patchwork.openwrt.org/patch/3345/
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35705
The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.
This makes OpenWrt always use vlan1 and vlan2 instead.
SVN-Revision: 35704
Fixes spurious build issues when changing target CFLAGS for specific ABI
options (such as ARM's floating point ABI).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35683
Bastian Bittorf reported that some of the silent freezes on a Linksys WRT54G
were due to overflow of the RX DMA ring buffer, which was created with 64
slots. That finding reminded me that I was seeing similar crashed on a netbook,
which also has a relatively slow processor. After increasing the number of
slots to 128, runs on the netbook that previously failed now worked; however,
I found that 109 slots had been used in one test. For that reason, the number
of slots is being increased to 256.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
SVN-Revision: 35671
Jo-Philipp Wich
Gabor Juhos
Jonas Gorski
Hauke Mehrtens
Florian Fainelli
Steven Barth