Commit Graph

814 Commits (ad65d9d7b264d6d17293c59469e770905d2f785a)

Author SHA1 Message Date
David Bauer 38f3433420 ramips: add missing SPDX identifier for EX6150
This adds the SPDX license identifier for the NETGEAR EX6150. It was
missed when submitting the original patch.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-31 20:59:08 +02:00
Rosen Penev 2159b25466 ramips: Increase GB-PC1 SPI frequency to 80MHz
The specific flash chip used (W25Q256FVEM) accepts 50MHz for read
requests and higher for others. 104MHz for fast reads. ramips seems to
be limited to 80MHz based on testing with higher values (no speedup).

Based on upstream commit: 97738374a310b9116f9c33832737e517226d3722

 time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s

 [test done with backported upstream v4.19 driver[1], for numbers on
  stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI
  frequency to 80MHz` commit message]

1. https://github.com/openwrt/openwrt/pull/1578

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[expanded note about spi driver version]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 09:01:46 +01:00
Rosen Penev 274439b780 ramips: Increase GB-PC2 SPI frequency to 80MHz
The flash chip on the board (Spansion S25FL256SAIF00) is rated to
support at least 50MHz for normal read requests according to the
datasheet. 133MHz for fast reads. However, ramips seems to be limited to
80MHz.

>From testing this, higher values do not improve speeds.

time dd if=/dev/mtdblock3 of=/dev/null bs=64k from

42.82s to 14.09s.

boot speed is also faster:
[   66.884087] procd: - init - vs
[   48.976049] procd: - init -

Since spi speed was requested:
[    3.538884] spi-mt7621 1e000b00.spi: sys_freq: 225000000

CPU is 900MHz:
[    0.000000] CPU Clock: 900MHz

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[fixed commit message by adding missing 0 in the spi-mt7621 clock output]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 09:01:23 +01:00
David Bauer 3f019bf96c ramips: add Netgear EX6150
SoC:   MediaTek MT7621
RAM:   64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi:  MediaTek MT7662E bgn 2SS
WiFi:  MediaTek MT7662E nac 2SS
BTN:   ON/OFF - Reset - WPS - AP/Extender toggle
LED:    - Arrow Right (blue)
        - Arrow Left (blue)
        - WiFi 1 (red/green)
        - WiFi 2 (red/green)
        - Power (green/amber)
        - WPS (Green)
UART:  UART is present as Pads on the backside of the PCB. They are
       located on the other side of the Ethernet port.
       3.3V - GND - TX - RX / 57600-8N1
       3.3V is the nearest one to the antenna connectors

Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).

You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash

Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:34:00 +00:00
Vladimir Kot 58becdb30d ramips: add support for ZyXEL Keenetic Start
Device specification:
- SoC: RT5350F
- CPU Frequency: 360 MHz
- Flash Chip: Winbond 25Q32 (4096 KiB)
- RAM: 32768 KiB
- 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
- 1x external, non-detachable antenna
- UART (J1) header on PCB (57800 8n1)
- Wireless: SoC-intergated: 2.4GHz 802.11bgn
- USB: None
- 3x LED, 2x button

Flash instruction:
1. Configure PC with static IP 192.168.1.2/24 and start TFTP server.
2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin"
   to "kstart_recovery.bin" and place it in TFTP server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power LED start blinking.
4. Router will download file from TFTP server, write it to flash and reboot.

Signed-off-by: Vladimir Kot <vova28rus@gmail.com>
[fixed git commit author and whitespace issues in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:34:00 +00:00
Tobias Welz 7c4b85ee27 ramips: add support for WIZnet WizFi630S board
The WIZnet WizFi630S board is in the miniPCIe form factor.

SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)

Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1).  Then get the
sysupgrade image from a tftp server.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:33:59 +00:00
Pawel Dembicki 67fced9ba3 ramips: add support for DLINK DIR-510L
The DIR-510L Wireless Router are based on the MT7620A SoC.

Specification:

-MediaTek MT7620A (580 Mhz)
-128 MB of RAM
-16 MB of FLASH
-802.11bgn radio
-1x 10/100 Mbps Ethernet
-2x internal, non-detachable antennas
-UART (J3) header on PCB (57600 8n1)
-1x bi-color LED (GPIO-controlled), 2x button
-JBOOT bootloader

Known issues:
-Ethernet port is used as LAN
-No communication with charger IC. (uart bitbang needed)

Installation:
Apply factory image via d-link http web-gui.

How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
    curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed whitespace issue in 10-rt2x00-eeprom]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-24 01:44:24 +01:00
Ozgur Can Leonard 201d3d1a82 ramips: Xiaomi MIR3G: detect board name from DTS
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
  Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
INAGAKI Hiroshi 5c11258297 ramips: add support for I-O DATA WN-AC733GR3
I-O DATA WN-AC733GR3 is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification

- SoC		: MediaTek MT7620A
- RAM		: DDR2 64 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz
  - 2.4 GHz : MT7620A (SoC), 2T2R
  - 5 GHz   : MT7610E, 1T1R
- Ethernet	: 10/100/1000 Mbps (RTL8367RB)
- LED/key	: 4x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J1: Vcc, RX, GND, TX from LED side
  - 57600n8

Flash instruction using factory image:

1. Boot WN-AC733GR3 normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-03-21 00:57:20 +01:00
Micke Prag c3a17ee4b3 ramips: add #pwm-cells property to MT76x8 dts
To be able to configure pwms the pwm driver needs to know the number off
cells in the "pwms" property. For this platform this is 2.

Signed-off-by: Micke Prag <micke.prag@telldus.se>
2019-03-18 20:43:09 +01:00
Chen Minqiang 7dfe357a3d ramips: HC5861 drop unused gpio group define in dts
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2019-03-13 16:25:34 +01:00
Ozgur Can Leonard d009033911 ramips: add support for Xiaomi Mi Router 3 Pro
Hardware:

CPU:   MediaTek MT7621AT (2x880MHz)
RAM:   512MB DDR3
FLASH: 256MB NAND
WiFi:  2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI:  5GHz 4x4 MT7615 a/n/ac  (Needs driver, See Issues!)
USB:   1x 3.0
ETH:   1x WAN 10/100/1000 3x LAN 10/100/1000
LED:   Power/Status
BTN:   RESET
UART:  115200 8n1

Partition layout and boot:

Stock Xiaomi firmware has the MTD split into (among others)

- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)

Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.

Note uboot's tftp flash install writes the transferred
image to both kernel partitions.

Installation:

Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.

The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:

nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot

Reverting to stock:

The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.

For this we do the following:

fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot

After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.

Issues:

OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.

See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
2019-03-13 16:25:34 +01:00
Piotr Dymacz 9b6413982c ramips: add support for ALFA Network Tube-E4G
ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on
MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem.

Specification:

- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 1x detachable antenna (modem main)
- 1x internal antenna (modem div)
- 1x GPS passive antenna (optional)
- 5x LED (all driven by GPIO)
- 1x button (reset)
- UART (4-pin, 2.54 mm pitch) header on PCB

Other:

Default SIM slot is selected at an early stage by U-Boot, based on
'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2
(micro). U-Boot also resets the modem, using #PERST signal, before
starting kernel.

Flash instruction:

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the LAN LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-11 22:00:26 +01:00
Chen Minqiang e15bda603a ramips: rework network settings for HC5861
dts: disable port4 and leave it ephy mode because it connect to nothing
switch port5 connected to GE port we use it as wan port

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2019-03-06 22:02:56 +01:00
Kip Porterfield f2c83532f9 ramips: add support for Belkin F9K1109v1
Device specification:
- SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz
- RAM: 64Mb
- Flash: 8MB (SPI-NOR)
- Ethernet: 10/100/1000 Mbps
- WLAN
	Wireless 1: SoC-integrated : 2.4/5 GHz
	Wireless 2: 2.4 GHz RT3092L
- LED: 2x USB, WAN, LAN
- Key: WPS, reset
- Serial: 4-pin header, (57600,8,N,1), 3.3V TTL,
	GND, RX, TX, V - J12 marking on board
- USB ports: 2 x USB 2.0

Flashing instructions:

Option 1 (from bootloader web)
- Hold reset button on the back of router when plugging
  in power (for at-least 10 seconds after plugged in)
- Connect to a Lan port
- Set computer IP to 10.10.10.3
- Go to http://10.10.10.123 in a web browser
- Click the Browse... Button and select the
   *squashfs.sysupgrade.bin file then click APPLY

Option 2 (from the stock admin web)
- Go to firmware upgrade
- Upload the **factory** image *initramfs.bin first
- Boot into openwrt
- From Luci web in openwrt upload the *squashfs.sysupgrade.bin

Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added v1 to the compatible identifier, added pciid for
the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi
to prepare for a possible F9K1103 patch]
2019-03-02 13:04:45 +01:00
Marcel Jost e6f047fa36 ramips: add TP-Link TL-WR802N-v4 support
This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n

Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED

Flash instruction:

The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 10 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Marcel Jost <majo@icutech.ch>
2019-02-28 11:26:10 +01:00
Thomas Vincent-Cross 25c0b41901 ramips: various Wavlink WL-WN575A3 fixes
* assign pinmux groups to gpio function for LEDs/buttons
* rename flash node to be more generic in line with other device nodes
* remove useless/incorrect eeprom property from wmac node
* correct base mac address for embedded switch

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
2019-02-28 11:26:10 +01:00
INAGAKI Hiroshi e52ad0f919 ramips: change status LED for Buffalo WHR-G300N
Buffalo WHR-G300N has a LED for power status indication, but it is not
connected to the GPIO and cannot be controlled by the kernel. So,
WHR-G300N uses "ROUTER" LED as the system status LED instead.

This commit changes it to use "DIAG" LED insted of "ROUTER" like
WHR-G301N in ath79 target.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-14 16:56:15 +01:00
David Bauer 7bf6b59724 ramips: various Netgear R6120 fixes
The R6120 has no 5GHz WLAN LED, the assigned GPIO in fact controls
the WAN LED.

Renames the LED accordingly in the device-tree.
Removes the 5GHz WLAN LED trigger.
Adds the correct WAN port LED trigger.

----

Currently, the MAC address for the Netgear R6120 is read from the NVRAM
partition. The offset for the MAC address however is not consistent
across devices or firmware versions.

Switch to using the factory partition like all other Netgear devices do.

----

The LAN ports of the R6120 are labled in reverse on the casing.

Adjust LuCI switchport numbering accordingly.

----

The WiFi eeprom offsets for the R6120 are currently wrong (5GHz offset
is bigger than the partition itself).

Fixes poor performance on 2.4 and 5 GHz.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-14 16:56:14 +01:00
INAGAKI Hiroshi f305ce5c35 ramips: add support for I-O DATA WN-AC1167GR
I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification:

- SoC     : MediaTek MT7620A
- RAM     : DDR2 64 MB
- Flash   : SPI-NOR 8MB
- WLAN    : 2.4/5 GHz, 2T2R
  - 2.4 GHz: MT7620A (SoC)
  - 5 GHz  : MT7612E
- Ethernet: 10/100/1000 Mbps (ext. MT7530)
- LED/key : 4x/3x (2x buttons, 1x slide-switch)
- UART    : through-hole on PCB
  - J2: TX, GND, RX, Vcc from SoC side
  - 115200n8

Flash instruction using factory image:

1. Boot WN-AC1167GR normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-14 16:56:14 +01:00
Chuanhong Guo be2b61e4f1 ramips: drop m25p,chunked-io from dts
This option was a spi nor hack which is dropped in commit
bcf4a5f474 ("ramips: remove chunked-io patch and set spi->max_transfer_size instead")

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [edit message]
2019-02-05 19:37:30 +01:00
Deng Qingfang 6621da55b7 ramips: enable MT7610E 5GHz radio of MT7620a_MT7610e EVB
This enables MT7610E of the EVB

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-02-05 19:37:30 +01:00
Petr Štetiar dd3ec40d3d ramips: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-02-05 16:28:12 +01:00
Petr Štetiar e8eaf794ec ramips: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-02-05 16:28:12 +01:00
Anton Arapov ae0a40d68d ramips: rb750gr3: License DTS as GPL-2.0-or-later OR MIT
Adding license in order to fully satisfy dts checklist:
- https://openwrt.org/submitting-patches#dts_checklist

Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Thibaut <hacks@slashdirt.org>
Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Chuanhong Guo <gch981213@gmail.com>
Acked-by: Andrew Yong <me@ndoo.sg>
Acked-by: Alex Maclean <monkeh@monkeh.net>
2019-02-01 06:35:13 +01:00
Rafał Miłecki acd790c150 ramips: specify "firmware" partition format for remaining devices
It results in calling the right MTD parser directly instead of trying
them one by one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[use the lzma splitter for the AR670W]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 21:46:33 +01:00
David Bauer 01dcd574a2 ramips: add support for Archer C50 v4
This adds support for the TP-Link Archer C50 v4.
It uses the same hardware as the v3 variant, sharing the same FCC-ID.

CPU:   MediaTek MT7628 (580MHz)
RAM:   64M DDR2
FLASH: 8M SPI
WiFi:  2.4GHz 2x2 MT7628 b/g/n integrated
WiFI:  5GHz 2x2 MT7612 a/n/ac
ETH:   1x WAN 4x LAN
LED:   Power, WiFi2, WiFi5, LAN, WAN, WPS
BTN:   WPS/WiFi, RESET
UART:  Near ETH ports, 115200 8n1, TP-Link pinout

Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.

Download a TP-Link image from their Wesite and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:

TP-Link image:             tpl.bin
OpenWRT sysupgrade image:  owrt.bin

 > dd if=tpl.bin of=boot.bin bs=131584 count=1
 > cat owrt.bin >> boot.bin

Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.

Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.

Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.

The boot.bin can now be uploaded and flashed using the web-recovery.

Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)

 > dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
 > dd if=tpl.bin of=tmp.bin bs=131584 count=1
 > dd if=tmp.bin of=boot.bin bs=512 skip=1
 > cat boot.bin >> tp_recovery.bin
 > cat owrt.bin >> tp_recovery.bin

Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.

Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.

U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.

Dual U-Boot
-----------
This is the first TP-Link MediaTek device to feature a split-uboot
design. The first (factory-uboot) provides recovery via TFTP and HTTP,
jumping straight into the second (firmware-uboot) if no recovery needs
to be performed. The firmware-uboot unpacks and executed the kernel.

Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5. Stock-firmware sets a flag in the "romfile" partition
before beginning to write and removes it afterwards. If the router boots
with this flag set, bootloader will automatically start Web-recovery and
listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT
factory image can be written.

By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.

It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 21:46:32 +01:00
Deng Qingfang c2bcdabf2a ramips: fix support for MX25L25635F flash
Patch picked from commit 82618062cf

This enables 4B opcodes for MX25L25635F, to fix the reboot crash
issue (FS#1120) At least 3 devices are using this flash
- GeHua GHL-R-001
- Youku YK1
- Newifi D1

Now the MX25L25635F can be correctly detected without breaking MX25L25635E
[ 3.034324] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 3.045962] m25p80 spi0.0: mx25l25635f (32768 Kbytes)
[ 3.056098] 4 fixed-partitions partitions found on MTD device spi0.0
[ 3.068748] Creating 4 MTD partitions on "spi0.0":

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added deprecation notice]
2019-01-26 17:10:19 +01:00
David Bauer 915fbd4e31 ramips: adjust Netgear R6120 model name
Adjust the model string and device title to match other Netgear routers
in the ramips target.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 10:41:03 +01:00
Mathias Kresin f5e61350e7 ramips: fix firmware splitter for edimax based boards
Use the correct splitter for board with the edimax header.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-19 12:51:04 +01:00
Anton Arapov 6ba58b7b02 ramips: cleanup the RB750Gr3 support
Always enable the pwr led and use the usr led for boot status indication.

Rename nodes in the dts, to match what is recommend in the devicetree
specification.

Increase the maximum spi frequency to 20MHz and drop the m25p,chunked-io
which isn't required on mt7621.

Use the BTN_0 keycode for the mode button. This board doesn't have any
wireless.

Use a more descriptive label for the reset button and the GPIO enabling
the usb vcc supply.

Use the beeper kernel module for the buzzer.

Fix the pinmux to switch only pins used as GPIOs to the GPIO function.
Add support for the PoE enable GPIO to the userspace. The PoE power
status can be read via GPIO7. Since OpenWrt doesn't have support for
reading inputs from userspace, prepare only the pinmux for the GPIO.

Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-05 12:28:22 +01:00
Anton Arapov 52f2d7d2a9 ramips: add RB750Gr3 native support
This patch adds support of MikroTik RouterBOARD 750Gr3, without the need
to reflashing the bootloader.

Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common

Since the image isn't compatible with RouterBOARD 750Gr3 installations
which have replaced the bootloader, the former used userspace boardname
is not added to the SUPPORTED_DEVICES, to prevent a brick while trying
to upgrade to the image with native support.

Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-05 12:28:22 +01:00
Paul Wassi 28a5674e33 treewide: fix spaces vs. tabs
Fix spaces vs. tabs issues in ath79 and ramips.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 16:37:20 +01:00
Deng Qingfang 5580a9dd31 ramips: add support for GeHua GHL-R-001
Specs
	SoC: MT7621AT
	RAM: 512MiB
	Flash: 32MiB MX25L25635F SPI NOR
	2.4G: MT7603EN
	5G: MT7612EN
	Ethernet: 4x GE ports (1x WAN, 3x LAN) with link status LEDs
	USB 3.0
	LEDs: POWER, 5G WIFI, 2.4G WIFI, USB, Internet.
	      The last two ones are controlled by GPIO
	UART: There are 2 UARTs (UARTLITE1/ttyS0 and UARTLITE3/ttyS1) on board.
	      UARTLITE1 is close to LEDs, and UARTLITE3 is close to flash chip.
	      The stock u-boot uses UARTLITE1 by default. Baud rate is 57600

Flash instruction
	1. telnet 192.168.9.1 2317, username is "root" and password is "admin"
	   One can alternatively use UART to log in
	2. Put OpenWrt firmware in a FAT32 USB drive, and connect it to the router
	   One can alternatively download the firmware via wget through Internet
	3. mtd write /path/to/openwrt.bin firmware
	4. reboot

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-12-29 16:03:30 +01:00
Deng Qingfang 0599cd90e1 ramips: fix MT7621 dtsi
Fix SysTick reg
Add uartlite2 and uartlite3 nodes

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-12-29 16:03:30 +01:00
Simon Quigley 9f0e233576 ramips: add support for DLINK DWR-922-E2
Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not
sure if supported, I didn't try), wireless router with QMI LTE embedded
modem is based on the MT7620N SoC.

Specification:

  * MediaTek MT7620N (580 Mhz)
  * 64 MB of RAM
  * 16 MB of FLASH
  * 802.11bgn radio
  * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  * 2x external, detachable (LTE) antennas
  * UART header on PCB (57600 8n1)
  * 6x LED (GPIO-controlled)
  * 1x bi-color Signal Strength LED (GPIO-controlled)
  * 2x button
  * JBOOT bootloader

The status led has been assigned to the dwr-922-e2:green:signalstrength
(lte signal strength) led. At the end of the boot it is switched off and
is available for lte operation. Works correctly also during sysupgrade
operation.

Installation:
Apply factory image via d-link http web-gui, or via recovery interface:

How to recover/revert to OEM firmware:
1.) Push and hold the reset button and turn on the power. Wait until all
    LEDs start rapidly blinking (~10sec.)
2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set
    one manually
3.) Upload original factory image via JBOOT http interface at IP
    192.168.123.254
4.) If http doesn't work, it can be done with curl command:
      curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.
5.) You can optionally telnet to 192.168.123.254 before or during the
    upload and it will report the flashing status, memory address etc.
6.) Once web UI and/or telnet says "Success", power cycle the router, or
    type "reboot" into the telnet session.

Signed-off-by: Simon Quigley <squigley@squigley.net>
[squashed commits, word wrap commit message, rename signal strenght led
name to match what is used for the DWR-921-C1 since they share the led
configuration, add label referenced in the aliases node]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-29 16:03:30 +01:00
Andreas Ziegler d492da702a ramips: mt7621: fix 5GHz WiFi LED on ZBT WG3526
This fixes the 5GHz WiFi LED which was previously not working.

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
2018-12-29 12:35:47 +01:00
Weijie Gao 74af8a833a ramips: add support for CreativeBox v1
Hardware:
SoC: MT7621
DRAM: 512MB DDR3
Flash: 32MB SPI-NOR
WiFi 2.4GHz: MT7603 @ PCIe0
WiFi 5.8GHz: MT7612 @ PCIe1
SATA: ASM1061 @ PCIe2

Interfaces:
GBE RJ45 x5
USB3.0 x1
eSATA (with USB2.0) x1
SATA x1
UART x1
I2C x1
JTAG x1

Flash instructions:
Through factory bootloader or firmware web interface

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-12-28 12:45:23 +01:00
NOGUCHI Hiroshi d020ae79ab ramips: add SPDX license identifier into some dts,dtsi
Acked-by: Mathias Kresin <dev@kresin.me>
Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
2018-12-28 12:45:23 +01:00
Petr Štetiar 0d23fd2ab2 treewide: dts: Remove default-state=off property from all gpio LED nodes
>From the Documentation/devicetree/bindings/leds/common.txt:

- default-state : The initial state of the LED. Valid values are "on", "off",
  and "keep". If the LED is already on or off and the default-state property is
  set the to same value, then no glitch should be produced where the LED
  momentarily turns off (or on). The "keep" setting will keep the LED at
  whatever its current state is, without producing a glitch.  The default is
  off if this property is not present.

So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:16:28 +01:00
NOGUCHI Hiroshi 83a97c53fa ramips: add support for Netgear R6350
Netgear R6350 is a wireless router, aka Netgear AC1750.

Specification:
- SoC: Mediatek MT7621AT (2 CPU cores, 4 threads)
- RAM: 128MiB (Nanya NT5CC64M16GP-DI)
- ROM: 128MiB NAND Flash (Macronix MX30LF1G18AC-TI)
- Wireless:
   for 11b/g/n (upto 300Mbps): MT7603
   for 11a/ac  (upto 1450Mbps) : MT7615, is not avaliable now
- Ethernet LAN speed: up to 1000Mbps
- Ethernet LAN ports: 4
- Ethernet WAN speed: up to 1000Mbps
- Ethernet WAN ports: 1
- USB ports: 1 (USB 2.0)
- LEDs: 4 (all can be controlled by SoC's GPIO)
- buttons: 2
- serial ports: unknown

Installation through telnet:
  - Copy kernel.bin and rootfs.bin to a USB flash disk,
    plug to usb port on the router.
  - Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
    (login if required, default: admin password)
  - You will see "Debug Enabled!"
  - Telnet 192.168.1.1 and login with "root"
  - ls /mnt/shares/ to find out path of your USB disk.
    'myUdisk' for example.
  - cd /mnt/shares/myUdisk
  - mtd_write write rootfs.bin Rootfs
  - mtd_write write kernel.bin Kernel
  - reboot

recovery when bricked:
  nmrpflash can be used to recover to the netgear firmware
  if a broken image was flashed.

The SC_PART_MAP partition suggests that an on flash partition table
exists. After implementing a partition parser/builder for the sercom
partition format, the definitions don't match the flash layout used by
the stock firmware.

It either means the partition format has not yet been completely
understood or it isn't used by the stock firmware. For now, use fixed
partitions instead.

Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[apply latest ramips changes and document the on flash partition map
issues]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-16 08:41:41 +01:00
Deng Qingfang 47381aadd5 ramips: several fixes for HC5x61
- Mark other partitions as read-only for HC5x61

 - Only enable USB and PCIe for HC5761/HC5861
   HC5661 doesn't have a USB port, and there is nothing attached to its PCIe.

 - Fix HC5761 switch ports
   HC5761 has only 3 ethernet ports (1x WAN + 2x LAN). Remove unused ports.

 - Fix HC5861 5GHz radio
   HC5861 has MT7612EN 5GHz WiFi chip, not MT7610EN.

 - Fix HC5761/HC5861 WiFi LEDs
   After 5GHz is enabled, it becomes wlan0. And 2.4GHz would be wlan1.

 - Fix HC5x61 image size
   It should be 15872k (0xf80000)

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-12-15 20:02:07 +01:00
Rafał Miłecki c56241c052 ramips: mt7621: specify "firmware" partition format for remaining devices
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-13 13:39:56 +01:00
Mathias Kresin 8e40fbff0b ramips: drop support for ALLNET ALL0239-3G and Sitecom WL-341 v3
Beside one exception, no one took care of these two remaining boards
still using the legacy image build code during the last two years.

Since OpenWrt 14.07 the ALLNET ALL0239-3G image building is broken.

The Sitecom WL-341 v3 image build code looks pretty hackish and broken.
It's questionable if the legacy image works as all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 11:01:59 +01:00
Russell Senior ed000fcaf2 ramips: fix firmware compatible string for dir860l-b1
In commit d70ec3008d, a firmware compatible
string of "denx,uimage" was added for the Dlink DIR-860L-B1. Unfortunately,
this was the wrong string. It needs "seama" instead.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-12-08 14:18:42 +01:00
Mathias Kresin ffa55386f1 ramips: fix dtc compiler warnings
The latest dtc compiler considers nodes named i2c or spi as the
respective bus:

  /pinctrl/i2c: incorrect #address-cells for I2C bus
  /pinctrl/spi: incorrect #address-cells for SPI bus

Rename the node to fix the false positives.

Fix the spi node unit address for the DWR-512-B and UBNT-ER-e50 to get
rid of the following warning:

  SPI bus unit address format error, expected "n"

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Chuanhong Guo 5563d49a39 ramips: disable sdhc for HC5661A
Currently OpenWrt doesn't support switching MT7628 into AP mode
(which is done by writing some undocumented registers in MTK SDK)
Without doing so, enabling SD breaks 4 FE ports and the SD controller
doesn't work since SD pins aren't configured correctly.

Disable SDHC on HC5661A to recover the 4 FE ports.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[drop the sdhci node completely]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Pawel Dembicki e9a9b7d1ed ramips: add support for D-Link DWR-118-A1
The DWR-118-A1 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 3x 10/100 Mbps Ethernet (3 LAN)
- 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN)
- 1x internal, non-detachable antenna
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- WIFI 5G LED not working
- flash is very slow

The status led has been assigned to the dwr-118-a1:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-12-03 15:34:56 +01:00
Mathias Kresin 55101877d3 ramips: mt7620: disable PCIe if nothing is attached
All boards neither expose the PCIe as Mini-PCIe nor have anything
attached to the PCIe Bus. Disable PCIe for those by dropping the node
from the dts files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-03 15:34:56 +01:00
Chen Minqiang 14b81c909f ramips: mt7620: add missing pci wifi nodes to dts files
These devices has pci wifi but not defined in dts:
 HC5761
 HC5861
 TINY-AC

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-12-03 15:34:56 +01:00
Pawel Dembicki 465d57370f ramips: specify "firmware" partition format in JBOOT devices
Specify firmware partition format by compatible string.

List of devices:
-DWR-116-A1
-DWR-118-A2
-DWR-512-B
-DWR-921-C1
-LR-25G001

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-30 00:22:04 +01:00
Valentín Kivachuk 30a7ab8f61 ramips: add support for MTC Wireless Router WR1201
MTC Wireless Router WR1201 is the OEM name of the board. It is also sold
rebranded as STRONG Dual Band Gigabit Router 1200.

Specification:
- SoC: MediaTek MT7621A (880 MHz)
- Flash: 16 MiB
- RAM: 128 MiB
- Wireless: 2.4Ghz(MT7602EN) and 5Ghz (MT7612EN)
- Ethernet speed: 10/100/1000
- Ethernet ports: 4+1
- 1x USB 3.0
- 1x microSD reader
- Serial baud rate of Bootloader and factory firmware: 57600

The OEM webinterface writes only as much bytes as listed in the
uImage header field to the flash. Also, the OEM webinterface
evaluates the name field of uImage header before flashing (the
string "WR1201_8_128")

To flash via webinterface, is mandatory to use first initramfs.bin
and after (from the OpenWrt) the sysupgrade.bin

Some notes:
- Some microSD will not work:

  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising SDIO card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising MMC card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising SDIO card
  mtk-sd 1e130000.sdhci: card claims to support voltages below defined range
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising MMC card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising SDIO card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising MMC card

Signed-off-by: Valentín Kivachuk <vk18496@gmail.com>
2018-11-30 00:20:28 +01:00
INAGAKI Hiroshi d70ec3008d ramips: specify "firmware" partition format
Specify firmware partition format by compatible string.

formats in ramips:

- denx,uimage
- tplink,firmware
- seama

It's unlikely but the firmware splitting might not work any longer for
the following boards, due to a custom header:

- EX2700: two uImage headers
- BR-6478AC-V2: edimax-header
- 3G-6200N: edimax-header
- 3G-6200NL: edimax-header
- BR-6475ND: edimax-header
- TEW-638APB-V2: umedia-header
- RT-N56U: mkrtn56uimg

But it rather looks like the uImage splitter is fine with the extra
header.

The following dts are not touched, due to lack of a compatible string in
the matching firmware splitter submodule:

- CONFIG_MTD_SPLIT_JIMAGE_FW
    DWR-116-A1.dts
    DWR-118-A2.dts
    DWR-512-B.dts
    DWR-921-C1.dts
    LR-25G001.dts
- CONFIG_MTD_SPLIT_TRX_FW
    WCR-1166DS.dts
    WSR-1166.dts
- CONFIG_MTD_SPLIT_MINOR_FW
    RBM11G.dts
    RBM33G.dts
- CONFIG_MTD_SPLIT_LZMA_FW
    AR670W.dts
- CONFIG_MTD_SPLIT_WRGG_FW
    DAP-1522-A1.dts

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-29 13:15:44 +01:00
Petr Štetiar 221d3e0234 ramips: bdcom-wap2100: Change DTS license to GPL-2.0-or-later OR MIT
Having MIT as alternative is sometimes preferred by upstream maintainers
and allows sharing that simple code with other projects. We don't really
want multiple DTS versions for the same device.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-29 13:15:44 +01:00
Felix Fietkau 5c9ad4fa6e ramips: fix MTD EEPROM offset for TL-WR840N v5
The previous offset was invalid and pointed to the end of the partition,
which was causing issues with mt76

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-29 11:45:44 +01:00
Petr Štetiar 8ba6e95eed ramips: bdcom-wap2100: Enable mt7610e 5GHz radio
The 5GHz radio of this device uses an mt7610e PCI-E chip, which has
been recently started to be supported.

 mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
 mt76x0e 0000:01:00.0: ASIC revision: 76100002
 mt76x0e 0000:01:00.0: Firmware Version: 0.1.00
 mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-28 23:37:29 +01:00
Petr Štetiar 26ad357192 ramips: bdcom-wap2100: Set firmware partition format to denx,uimage
Specify firmware partition format to denx,uimage in compatible DTS property.

 2 uimage-fw partitions found on MTD device firmware
 Creating 2 MTD partitions on "firmware":
 0x000000000000-0x00000017f72b : "kernel"
 0x00000017f72b-0x000000f70000 : "rootfs"

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-28 23:37:29 +01:00
Petr Štetiar 795211093f ramips: bdcom-wap2100: Fix boot failure by adding partitions compatible property
Flash partitions were moved under partition table node, but addition of
compatible property was omitted which lead to following boot failure:

 VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
 Please append a correct "root=" boot option; here are the available partitions:
 1f00           16384 mtdblock0
  (driver?)
 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Fixes: e4d9217f (ramips: improve BDCOM WAP2100-SK support)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-28 23:37:29 +01:00
Roger Pueyo Centelles cb6a8aa584 ramips: mt7620: add DIR-810L's mt7610e 5 GHz radio
The 5 GHz radio of this device uses an mt7610e pci-e chip, which has
been recently added support.

Tested on the actual device as AP and client, TCP throughput ~90 Mbps
U/D.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-11-28 01:11:38 +01:00
Nishant Sharma df3e0b5806 ramips: add support for UniElec U7621-06-512M-64M variant
Add support for UniElec U7621-06 variant with 512MB RAM and 64MB flash.

Additional specs are below:

CPU: MT7621 (880Mhz)
Bootloader: Ralink U-Boot
Flash: 64MB
 - U-Boot identifies as Macronix MX66L51235F
 - kernel identifies as MX66L51235l (65536 Kbytes)
RAM: 512MB

Rest of the details as per commit 46ab81e405 ("ramips add support for
UniElec U7621-06")

Signed-off-by: Nishant Sharma <nishant@unmukti.in>
[use generic board detection, add firmware partition compatible, extend
firmware partition to use all of the remaining flash space, add a
maximum image size matching the firmware partition size]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-28 01:11:38 +01:00
Thomas Vincent-Cross a160f50d4f ramips: add support for Wavlink WL-WN570HA1
This commit adds support for the Wavlink WL-WN570HA1, a dual-band PoE
wireless router with the following specifications:

 - CPU: MediaTek MT7688AN 580MHz
 - Flash: 8MB
 - RAM: 64MB
 - Ethernet: 1x 10/100Mbps
 - 2.4 GHz: 802.11b/g/n SoC, 1T1R, 27 dBm
 - 5 GHz: 802.11a/n/ac MT7610E, 1T1R, 25 dBm
 - Antennas: 2x external (1 per radio), detachable
 - LEDs: 3 programmable + Wi-Fi, WAN/LAN, Power
 - Buttons: Reset

Flashing instructions:

Factory U-boot launches a TFTP client if reset button is pressed during power-on.
Rename the sysupgrade file and configure TFTP as follows:

 - Client (WL-WN570HA1) IP: 192.168.10.101
 - Server IP: 192.168.10.100
 - Filename: firmware.bin

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
[use generic board detection, add firmware partition compatible]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-28 00:50:35 +01:00
Matthias Badaire 1100ba43db ramips: fix RavPower WD03 SoC dtsi include
The RavPower WD03 is a mt7620n based baord. With the change applied, I2C
should work now with the RavPower WD03.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-27 21:11:54 +01:00
Mathias Kresin aa82fdf110 ramips: fix GB-PC1/PC2 build error
With ed25e3ac02 ("ramips: fix some clocks in mt7621.dtsi") the
cpuclock node was dropped from the mt7621.dtsi without removing the
references to this node from the GB-PC1/PC2 dts files.

Remove them now, to fix the build error.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 19:40:31 +01:00
Mathias Kresin d7494f30f5 ramips: fix Lava LR-25G001 invalid led names
It has to be <board>:<colour>:<function> and is expected exactly this
way by the userspace scripts.

While at it, fix some whitespace issues in the dts file and rename the
flash node as required upstream.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 19:40:31 +01:00
Mathias Kresin be3e69d991 ramips: rt2880: fix pci cells definition
Set the correct number of cells to fix "property has invalid length" dtc
compiler warnings.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin e4d9217fe5 ramips: improve BDCOM WAP2100-SK support
Use the generic board detection instead of the target specific one as
all recent additions are doing.

Setup the USB led via devicetree (a58535771f) and include the required
driver by default. Merge the led userspace setting with an existing
identical case.

Use the wps led for boot status indication.

Move the partitions into a partition table node (6031ab345d) and drop
needless labels. Drop misplaced cells properties (53624c1702).

Cleanup the pinmux and only switch pins to gpio functions which a
referenced as gpio in the dts.

Match the maximum image size with the size of the firmware partition.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin 71ba834cf1 ramips: add Sanlinking Technologies D240 pinmux quirk
The sd function of the nd_sd group configures two of the groups pins as
gpios. The pins are used as PCIe reset/power.

Due to the driver load order, the pins are configured way to late if
triggered by the sd-card driver.

To not introduce another kind of driver load order dependency and
configure the pins as early as possible, means during pinmux driver
load.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin 9ebce69611 ramips: revert fix rt3883 pci pinmux
This reverts commit dcdc6d9dad.

Even if described this way in the datasheet, it causes a bootloop on a
RT-N56U (v1):

  of-flash 1c000000.nor-flash: do_map_probe() failed for type cfi_probe
  of-flash 1c000000.nor-flash: do_map_probe() failed
  VFS: Cannot open root device “(null)” or unknown-block(0,0): error -6

Fixes: FS#1930

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin 8ec1a66c34 ramips: improve Skylab SKW92A support
Use the generic board detection instead of the target specific one as
all recent additions are doing.

Add the wireless led according the gpio number from the datasheet.
Rename the board part of the leds to match the name used for the
compatible string. Finally, do not hijack the wps led for boot status
indication longer than necessary.

Merge userspace config into existing cases.

Include the manufacture Name in the dts model string.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Pawel Dembicki 20b09a2125 ramips: add support for Lava LR-25G001
The Lava LR-25G001 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 5x 10/100/1000 Mbps AR8337 Switch (1 WAN AND 4 LAN)
- 2x external, detachable antennas
- 1x USB 2.0
- UART (J3) header on PCB (57600 8n1)
- 8x LED (3x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- Work only three Gigabit ports (3/5, 1 WAN and 2LAN)

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-26 12:16:52 +01:00
Weijie Gao ed25e3ac02 ramips: fix some clocks in mt7621.dtsi
As the cpu clock calculation has been fixed, the clock for gic and spi
should be also fixed.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao c7ca224299 ramips: fix cpu clock of mt7621 and add dt clk devices
For a long time the mt7621 uses a fixed cpu clock which causes a problem
if the cpu frequency is not 880MHz.

This patch fixes the cpu clock calculation and adds the cpu/bus clkdev
which will be used in dts.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao f5af8be636 ramips: fix register range of memc node in mt7621.dtsi
The memc node from mt7621.dtsi has incorrect register resource.
Fix it according to the programming guide.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Lorenzo Bianconi e612e60517 ramips: add mt76x0 node to RT-AC51U device tree
Introduce mt76x0e device tree node in RT-AC51U dts.
Define mt76x0e mtd partition and offset

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
2018-11-26 12:05:47 +01:00
Petr Štetiar 16b950c981 ramips: Add support for ZTE ZXECS EBG3130 aka BDCOM WAP2100-SK
On the bottom sticker it's branded as ZTE ZXECS EBG3130 device, but in factory
OpenWrt image it's referenced as BDCOM WAP2100-SK device.

Specifications:

- SoC: MediaTek MT7620A
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 5 FE ports
- Wireless radio: 2T2R 2.4 GHz and 1T1R 5 GHz (MT7610EN, unsupported)
- UART: 1 x UART on PCB marked as J2 (R=RX, T=TX, G=GND) with 115200 8N1 config
- LEDs: Power, FE ports 1-5, WPS, USB, RF 2.4G, RF 5G
- Other: USB port, SD card slot and 2x external antennas (non-detachable)

Flashing instructions:

A) The U-Boot has HTTP based firmware upgrade

  A1) Flashing notes

  We've identified so far two different batches of units, unfortunately
  each batch has different U-Boot bootloader flashed with different
  default environment variables, thus each batch has different IP address
  for accessing web based firmware updater.

  * First batch has web based bootloader IP address 1.1.1.1
  * Second batch has web based bootloader IP address 192.168.1.250

  In case you can't connect to either of those IPs, you can try to get
  the default IP address via two methods:

  A1.1) Serial console, then the IP address is visible during the boot

   ...
   HTTP server is starting at IP: 1.1.1.1
   raspi_read: from:40004 len:6
   HTTP server is ready!
   ...

  A1.2) Over telnet/SSH using this command:

   root@bdcom:/# grep ipaddr= /dev/mtd0
   ipaddr=1.1.1.1

  A2) Flashing with browser

  * Change IP address of PC to 1.1.1.2 with 255.255.255.0 netmask
  * Reboot the device and try to reach web based bootloader in the
    browser with the following URL http://1.1.1.1

  * Quickly select the firmware sysupgrade file and click on the
    `Update firmware` button, this all has to be done within 10 seconds,
    bootloader doesn't wait any longer

   If done correctly, the web page should show UPDATE IN PROGRESS page
   with progress indicator. Once the flashing completes (it takes roughly
   around 1 minute), the device will reboot to the OpenWrt firmware

  A3) Flashing with curl

   sudo ip addr add 1.1.1.2/24 dev eth0
   curl \
      --verbose \
      --retry 3 \
      --retry-delay 1 \
      --retry-max-time 30 \
      --connect-timeout 30 \
      --form "firmware=@openwrt-ramips-mt7620-BDCOM-WAP2100-SK-squashfs-sysupgrade.bin" \
      http://1.1.1.1

   Now power on the router.

B) The U-boot is based on Ralink SDK so we can flash the firmware using UART.

   1. Configure PC with a static IP address and setup an TFTP server.
   2. Put the firmware into the tftp directory.
   3. Connect the UART line as described on the PCB (G=GND, R=RX, T=TX)
   4. Power up the device and press 2, follow the instruction to set device and
      tftp server IP address and input the firmware file name. U-boot will then load
      the firmware and write it into the flash.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-26 12:05:44 +01:00
Roman Yeryomin ae2b43b873 ramips: fix ethernet for f5d8235-v2 board
Belkin F5D8235 v2 has two ethernet switches on board.
One internal rt3052 and rtl8366rb on rgmii interface.
Looks like internal switch settings were lost in
translation to device tree infrastructure.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-11-26 09:58:17 +01:00
Russell Senior e42327aa89 ramips: add support for Skylab SKW92A in EVB
Specifically, SKW92A_E16, described here:

  http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x u.FL
- Power by micro-USB connector at USB1 on EVB
- UART via micro-USB connector at USB3 on EVB (57600 8n1)
- 5x Ethernet LEDs
- 1x WLAN LEDs
- 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next
  to daughter board on EVB
- WPS/Reset button (S2 on EVB)
- RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board

Flash instruction:

>From Skylab firmware:

1. Associate with SKYLAP_AP
2. In a browser, load: http://10.10.10.254/
3. Username/password: admin/admin
4. In web admin interface: Administration / Upload Firmware, browse to
   sysupgrade image, apply, flash will fail with a message:
   Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data!
5. Telnet to 10.10.10.254, drops you into a root shell with no credentials
6. # cd /var
7. # mtd_write -r write tmpFW mtd4
   Unlocking mtd4 ...
   Writing from tmpFW to mtd4 ... [e]
8. When flash has completed, you will have booted into your firmware.

>From U-boot via TFTP and initramfs:

1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server
2. Connect to serial console at USB3 on EVB
3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "1"
7. At u-boot prompts:
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin
8. Move ethernet to port 0 (WAN) on EVB
9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash
   with sysupgrade.

>From U-boot via TFTP direct flash:

1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server
2. Connect to serial console at USB3 on EVB (57600 8N1)
3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "2"
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin
8. When transfer is complete or as OpenWrt begins booting, move ethernet to
   port 0 (WAN).

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-26 09:47:27 +01:00
Felix Fietkau b318edb999 ramips: add missing DTS frequency limit for the 5 GHz radio on Archer C20i
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-06 22:25:49 +01:00
Martin Weinelt 0411813c6f
ramips: fix leds on GL.iNet GL-MT300N-V2
The WAN LED now shows the link state. It's color is green,
not blue.

Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
2018-11-02 21:43:15 +01:00
Mathias Kresin c074239c79 ramips: move status led unset to devicetree
Release the led used for boot status indication via devicetree instead
of setting a default off trigger in userspace.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Mathias Kresin 8f4dfadd5a ramips: add support for indicating the boot state using multiple leds
Use diag.sh version used for other targets supporting different leds
for the different boot states.

The existing led sequences should be the same as before.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Mathias Kresin 772b27c207 ramips: set F5D8235 v1 usb led trigger via devicetree
Assign the usbdev trigger via devicetree and drop the userspace
handling of the usb leds.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Mathias Kresin a58535771f ramips: set usb led trigger via devicetree
Assign the usbdev trigger via devicetree for all subtargets and drop
the userspace handling of the usb leds.

With the change all usb ports are triggering the usb led instead of
only usb 1.1 XOR usb 2.0 XOR usb 3.0 as it was before.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Emil Muratov 8e6bc1a5be ramips: fix power LED DTB for wt3020
Since c134210 power LED is no longer lights after boot-up.
Reversing gpio polarity makes it work as it should be.

Signed-off-by: Emil Muratov <gpm@hotplug.ru>
2018-09-26 20:35:07 +02:00
Carlo Nel 6bbb220255 ramips: add support for TP-Link TL-MR3020 v3
TP-Link TL-MR3020 v3 is a pocket-size router based on MediaTek MT7628N.

This PR is based on the work of @meyergru[1], with his permission.

Specification:
- MediaTek MT7628N/N (575 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet

Flash instruction:

The only way to flash the image in TL-MR3020 v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-mr3020-v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

[1] https://github.com/meyergru/lede-source/commits/TL-MR3020-V3

Signed-off-by: Carlo Nel <carlojnel@gmail.com>
2018-09-06 21:36:42 +02:00
Mathias Kresin 563a5b5f94 ramips: add mt7620/1 sdhci pinmux
Set the pins to the required mode via the pinmux driver. It allows to
get rid of the pinmux related code in the sd card driver.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin a14097e8e0 ramips: fix mt7620a ND/SD pins pinmuxes
Drop the nd_sd gpio pinmux in case sdcard is used. They're mutually
exclusive and for most of the boards not even used as GPIOs.

If the pins are in sdcard mode, the pins ND_WE_N and ND_CS_N are still
GPIOs (#45 and #46).

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin 2cc7980dcb ramips: reference node by label
Reference the HC5661A sdhci node by label instead of by the full path.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin a6e11ccb13 ramips: fix rt3883 pinmux for second SPI
The rt3883 doesn't have a pinmux group named spi_cs1. The cs1 is part
of the pci group. The function pci-func enables the second chip select.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 21:00:58 +02:00
Mathias Kresin dcdc6d9dad ramips: fix rt3883 pci pinmux
The PCI pins need to be set to "PCI Host support one device" to allow
the use of one PCI device and flash memory.

The pci-fnc function is intended to be used if no PCI is used but
flash, nand or the codec functionality is.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 21:00:58 +02:00
Mathias Kresin 43df31f64d ramips: add missing zbt-cpe102 diag led
Based on the userspace led configuration it's quite obvious that the
4g-0 led should be used for boot status indication.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:34:09 +02:00
Mathias Kresin 99045dfc59 ramips: express diag led handling via devicetree
Use the default-state property to express the desired led handling in
the devicetree source file instead of the userspace.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:34:07 +02:00
Mathias Kresin 56e6ebdea4 ramips: fix multi colour led handling
All boards either have a multi colour led or a single lightpipe. It
makes it impossible to handle the LEDs individual. Change the LED
config for these boards to take it into account.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:24:49 +02:00
Paul Wassi e348ccc4e6 treewide: fix some cosmetic glitches in dts files
- fix single spaces hidden by a tab
- replace indentation with spaces by tabs
- make empty lines empty
- drop trailing whitespace
- drop unnecessary blank lines

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-08-27 19:31:17 +02:00
Mathias Kresin 3601c3de23 ramips: fix mt7620 pinmux for second SPI
The mt7620 doesn't have a pinmux group named spi_cs1. The cs1 is part
of the "spi refclk" group. The function "spi refclk" enables the second
chip select.

On reset, the pins of the "spi refclk" group are used as reference
clock and GPIO.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-27 19:31:17 +02:00
Thibaut VARÈNE bbe2cf657c ramips: fix RBM11G partitioning
This patch improves faf64056dd by correcting
the partition scheme for the "RouterBoot" section of the flash.

The partition scheme initially submitted is incorrect and does not reflect
the actual flash structure.

The "RouterBoot" section (name matching OEM) is subdivided in several
static segments, as they are on ar71xx RB devices albeit with different
offsets and sizes.
The naming convention from ar71xx has been preserved, except for the
bootloaders which are named "bootloader1" and "bootloader2" to avoid
confusion with the master "RouterBoot" partition.
The preferred 'fixed-partitions' DTS node syntax is used, with nesting
support as introduced in 2a598bbaa3.
"partition" is used for node names, with associated "label" to match
policy set by 6dd94c2781.

Leave a note in DTS to explain how the original author selected the SPI speed.

Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
2018-08-24 11:53:51 +02:00
Thibaut VARÈNE b90cad2c2e ramips: fix RBM33G partitioning
This patch improves 5684d08741 by correcting
the partition scheme for the "RouterBoot" section of the flash.

The partition scheme initially submitted is incorrect and does not reflect
the actual flash structure.

The "RouterBoot" section (name matching OEM) is subdivided in several
static segments, as they are on ar71xx RB devices albeit with different
offsets and sizes.
The naming convention from ar71xx has been preserved, except for the
bootloaders which are named "bootloader1" and "bootloader2" to avoid
confusion with the master "RouterBoot" partition.
The preferred 'fixed-partitions' DTS node syntax is used, with nesting
support as introduced in 2a598bbaa3.
"partition" is used for node names, with associated "label" to match
policy set by 6dd94c2781.

The OEM source code also define a "RouterBootFake" partition at the
beginning of the secondary flash chip: to avoid trouble if OEM ever makes
use of that space, it is also defined here.

The resulting partition scheme looks like this:
[   10.114241] m25p80 spi0.0: w25x40 (512 Kbytes)
[   10.118708] 1 fixed-partitions partitions found on MTD device spi0.0
[   10.125049] Creating 1 MTD partitions on "spi0.0":
[   10.129824] 0x000000000000-0x000000040000 : "RouterBoot"
[   10.136215] 5 fixed-partitions partitions found on MTD device RouterBoot
[   10.142894] Creating 5 MTD partitions on "RouterBoot":
[   10.148032] 0x000000000000-0x00000000f000 : "bootloader1"
[   10.154336] 0x00000000f000-0x000000010000 : "hard_config"
[   10.160665] 0x000000010000-0x00000001f000 : "bootloader2"
[   10.167046] 0x000000020000-0x000000021000 : "soft_config"
[   10.173461] 0x000000030000-0x000000031000 : "bios"
[   10.190191] m25p80 spi0.1: w25q128 (16384 Kbytes)
[   10.194950] 2 fixed-partitions partitions found on MTD device spi0.1
[   10.201271] Creating 2 MTD partitions on "spi0.1":
[   10.206071] 0x000000000000-0x000000040000 : "RouterBootFake"
[   10.212746] 0x000000040000-0x000001000000 : "firmware"
[   10.307216] 2 minor-fw partitions found on MTD device firmware
[   10.313044] 0x000000040000-0x000000220000 : "kernel"
[   10.319002] 0x000000220000-0x000001000000 : "rootfs"
[   10.324906] mtd: device 9 (rootfs) set to be root filesystem
[   10.330678] 1 squashfs-split partitions found on MTD device rootfs
[   10.336886] 0x000000b40000-0x000001000000 : "rootfs_data"

Leave a note in DTS to explain how the original author selected the SPI speed.

Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
[rmilecki: dropped "RouterBootFake" partition]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-08-24 11:46:48 +02:00
NOGUCHI Hiroshi ad10e71bec ramips: add support for ELECOM WRC-1900GST
ELECOM WRC-1900GST is a wireless router, based on Mediatek MT7621A.
This is almost same as WRC-2533GST except wireless specs.

Specifications:

  - SoC : MT7621A (four logical CPU cores)
  - RAM : 128MiB
  - ROM : 16MiB of SPI NOR-FLASH
  - wireless :
          5GHz : 3T3R up to 1300Mbps/11ac with MT7615
          2.4GHz : 3T3R up to 600Mbps/11n with MT7615
  - Ethernet : 5 ports, all ports is capable of 1000base-T
  - Ether switch : MT7530 (MT7621A built-in)
  - LEDs : 4 LEDs
  - buttons : 2 buttons and 1 slide-switch
  - UART : header is on PCB, 57600bps

Flash instruction using factory image:

 1. Connect the computer to the LAN port of WRC-1900GST
 2. Connect power cable to WRC-1900GST and turn on it
 3. Access to "https://192.168.2.1/" and open firmware update
    page ("ファームウェア更新")
 4. Select the OpenWrt factory image and click apply ("適用")
    button
 5. Wait ~150 seconds to complete flashing

Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
2018-08-23 22:42:09 +02:00
Mathias Kresin b8996ea08a ramips: fix compatibles in SoC dtsi
The former used compatibles aren't defined anywhere and aren't used by
the devicetree source files including them.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-23 22:40:59 +02:00
Mathias Kresin b88e03e2d4 ramips: fix GL-MT300N-V2 SoC compatible
According to abbfcc8525 ("ramips: add support for GL-inet
GL-MT300N-V2") the board has a MediaTek MT7628AN. Change the SoC
compatible to match the used hardware.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-23 22:40:59 +02:00
Mathias Kresin 28de86e816 ramips: drop not existing groups from pinmux
RT5350 neither have rgmii nor a mdio pinmux group. MT7628an doesn't
have a jtag group. Having these groups defined might cause a boot
panic.

The pin controller fails to initialise for kernels > 4.9 if invalid
groups are used. If a subsystem references a pin controller
configuration node, it can not find this node and errors out. In worst
case it's the SPI driver which errors out and we have no root
filesystem to mount.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-23 22:40:59 +02:00
Cezary Jackiewicz 37af596593 ramips: add support for D-Link DWR-118-A2
The DWR-118-A2 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612EN)
- 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN)
- 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN)
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- GELAN not working
- flash is very slow

The status led has been assigned to the dwr-118-a2:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-08-15 07:42:36 +02:00
Deng Qingfang d20f4fc628 ramips: add support for HiWiFi HC5861B
HiWiFi "Gee Enjoy1200" HC5861B is a dual-band router based on MediaTek MT7628AN
https://www.hiwifi.com/enjoy-view

Specifications:
- MediaTek MT7628AN 580MHz
- 128 MB DDR2 RAM
- 16 MB SPI Flash
- 2.4G MT7628AN 802.11bgn 2T2R 300Mbps
- 5G MT7612EN 802.11ac 2T2R 867Mbps
- 5x 10/100 Mbps Ethernet

Flash instruction:
1. Get SSH access to the router
2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one
3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP
4. Run `mtd write /tmp/<filename> firmware`
5. reboot

Everything is working

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-08-14 10:21:32 +02:00
Daniel Gimpelevich 1d3ea7874d ramips: fix BR-6478ACv2 support
The wholesale changes introduced in commit f9b8328 missed this DTS file
because it hadn't been merged yet. This patch brings it in line to match
the other mt7620a devices' DTS files.

Additionally, the Internet LED is now labeled correctly and set to unused
by default, since the WAN interface is not known in every configuration.

Using sysupgrade between images before and after this commit will require
the -F flag.

Tested-by: Rohan Murch <rohan.murch@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[drop internet led default setting]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-13 08:37:19 +02:00
Ludwig Thomeczek 5543d63fc8 ramips: add support for Netgear R6120
This patch adds support for the Netgear R6120, aka Netgear AC1200.

Specification:
- SoC: MediaTek MT7628 (580 MHz)
- Flash: 16 MiB
- RAM: 64 MiB
- Wireless: 2.4Ghz(builtin) and 5Ghz (MT7612E)
- LAN speed: 10/100
- LAN ports: 4
- WAN speed: 10/100
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600

To flash use nmrpflash with the provided factory.img.
Flashing via webinterface will not work, for now.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2018-08-13 08:37:19 +02:00
Mathias Kresin 3b1213a377 ramips: use #include syntax for dtsi files
Use the same syntax for including dtsi for all dts files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 07:24:03 +02:00
Daniel Gimpelevich 5a6229a93d ramips: remove superfluous & confusing DT binding
Mediatek has a reference platform that pairs an MT7620A with an MT7530W,
where the latter responds on MDIO address 0x1f while both chips respond on
0x0 to 0x4. The driver special-cases this arrangement to make sure it's
talking to the right chip, but two different ways in two different places.
This patch consolidates the detection without the current requirement of
both tests to be separately satisfied in the DTS.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2018-08-06 07:05:37 +02:00
Daniel Gimpelevich f72fa883b3 ramips: add support for Edimax BR-6478AC v2
Roll-up of patches by Rohan Murch, Hans Ulli Kroll, and James McKenzie.
Taken from https://forum.openwrt.org/viewtopic.php?id=67192 and updated.

Specification:
- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Macronix MX25L6405D
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7612E 5GHz 802.11ac
- Switch: Mediatek MT7530W Gigabit Switch
- USB: Yes 1 x 2.0

Installation:
1. Download sysupgrade.bin
2. Open vendor web interface
3. Choose to upgrade firmware
4. After reboot connect via ethernet at 192.168.1.1

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2018-08-06 07:05:37 +02:00
Alex Maclean 6031ab345d ramips: move partitions into partition table node
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-08-04 08:39:35 +02:00
Mathias Kresin 6dd94c2781 ramips: unify partition node names in dts files
Use partition@ as name for all partition nodes. Add a label where
necessary.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin bfd65fc4ab ramips: fix whitespace and comment issues in dts
Fix space vs. tabs issue and trainling whitespaces. Use C style
comments or drop the comments if they explain what is already to see in
the devicetree parameters.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin 53624c1702 ramips: fix dtc warnings
Fix individual boards dtc warnings or obvious mistakes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin 6384e0d16a ramips: fix hnat dtc warning
The hardware NAT node has the same reg/unit as the ethernet node. One
of them need to be a child of the other.

Make the hardware NAT node a child of the ethernet node since the it
"reference" the netdev in its properties.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin f9b8328d79 ramips: fix pci/pcie related dtc warnings
Add the ranges property to the PCI bridges where missing. Add the unit
address to PCI bridge where missing.

Rework the complete rt3883 pci node. Drop the PCI unit nodes from the
dtsi. They are not used by any dts file and should be rather in the dts
than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree
syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the
pci interrupt controller out of the pci node. It doesn't share the same
reg and therefore should be an independent/SoC child node.

Move the pci related rt3883 pinctrl setting to the dtsi instead of
defining the very same for each rt3883 board.

If the device_type property is used for PCI units, the unit is treated
as pci bridge which it isn't. Drop it for PCI units.

Reference pci-bridges or the pci node defined in the dtsi instead of
recreating the whole node hierarchy. It allows to change the referenced
node in the dtsi without the need to touch all dts.

Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips
are the first device on the bus. The unit address has to be the bus
address instead of the PCI vendor/device id.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin d8e7a526a3 ramips: use ralink,nr-gpio instead of ralink,num-gpios
Since commit c1e7738988f5 ("checks: add gpio binding properties check")
dtc treats any *-gpios and *-gpio property as phandle at least during
checks. The only whitelisted property is nr-gpio.

Use ralink,nr-gpio in favour of ralink,num-gpios to get rid of false
positive warnings.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin 1bad2b74ae ramips: fix cpu interrupt controller dtc warnings
The cpu interrupt controller doesn't have a reg property, hence we
can't use a unit address in the node name.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin b9dbf3f3c8 ramips: fix cpu related dtc warnings
We need a reg property if we are using a unit address.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
INAGAKI Hiroshi ce93445cd6 ramips: add support for ELECOM WRC-2533GST
ELECOM WRC-2533GST is a 2.4/5 GHz band 11ac rotuer, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Core, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 4T4R 2.4/5 GHz wifi
  - MediaTek MT7615
- 5x 10/100/1000 Mbps Ethernet
- 4x LEDs, 6 keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Connect the computer to the LAN port of WRC-2533GST
2. Connect power cable to WRC-2533GST and turn on it
3. Access to "https://192.168.2.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用")
button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-07-30 15:55:21 +02:00
Thibaut VARÈNE 3fd4db76b0 ramips: fix RBM11G name
The device name is corrected to match the hardware-stored (in hard config
flash space) device name.

Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:43:37 +02:00
Thibaut VARÈNE a9494bb425 ramips: fix RBM33G name
The device name is corrected to match the hardware-stored (in hard config
flash space) device name.

Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:43:37 +02:00
LoveSy 974a2b1aa9 ramips: mmc: Add SD card support to HC5661A
Tested on HC5661A and it now fixes the issue that when enabling sd card
in HC5661A, the wan and 3 lan ports will down.

Known issue:
- When enabling SD card support, the led light of system will down and the rest 2 lights keep working.

Signed-off-by: LoveSy <shana@zju.edu.cn>
2018-07-30 10:43:37 +02:00
Chuanhong Guo c9c4b2116c ramips: Use dts alias based status led
Also fix several typos in led node name.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-16 15:12:18 +02:00
Peter Lundkvist 2eeb4b78c6 ramips: TP-Link TL-WR902AC v3: add missing wps button
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
2018-07-12 18:15:33 +02:00
Ademar Arvati Filho 16d6a63f85 ramips: add support for Blueendless Kimax U35WF
Blueendless Kimax U35WF is a 3,5" HDD Enclosure with Wi-Fi and Ethernet

Patch rewritten from: https://forum.openwrt.org/viewtopic.php?id=66908
Based on: https://github.com/lede-project/source/pull/965

Specification:
- SoC: MediaTek MT7620N
- CPU/Speed: 580 MHz
- Flash-Chip: KH25L12835F Spi Flash
- Flash size: 16 MiB
- RAM: 64 MiB
- LAN: 1x 100 Mbps Ethernet
- WiFi SoC-integrated: 802.11bgn
- 1x USB 2.0
- UART: for serial console

Installation:
1. Download sysupgrade.bin
2. Open vendor web interface
3. Choose to upgrade firmware
3. After reboot connect via ethernet at 192.168.1.1

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-07 21:07:40 +02:00
INAGAKI Hiroshi 0b83a23560 ramips: add support for I-O DATA WN-AX1167GR
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 115200 bps (U-Boot, OpenWrt)

Stock firmware:

In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.

(excerpt from dmesg):

MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"

The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.

If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.

(example):

## Booting image at bc800000 ...
Bad Magic Number,FFFFFFFF
Boot from KERNEL 1  !!
## Booting image at bc060000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.50
   Image Type:   MIPS Linux kernel Image (lzma compressed)
   Data Size:    1865917 Bytes = 1.8 MB
   Load Address: 80001000
   Entry Point:  80001000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!

Starting kernel ...

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-07-07 21:07:40 +02:00
Romain MARIADASSOU ce31bdc20c ramips: add support for TL-WA801ND v5
Specification:

- System-On-Chip: MediaTek MT7628NN
- CPU/Speed: 580 MHz
- Flash-Chip: ELM Technology GD25Q64
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn

Currently the only method to install openwrt for the first time is via
TFTP recovery. After first install you can use regular updates.

Flash instructions:

1) To flash the recovery image, start a TFTP server with IP address
   192.168.0.66 and serve the recovery image named tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS and Reset
   button and power it up. Keep pressing the WPS/Reset button for
   10 seconds or until the lock LED is lighting up.
   It will try to download the recovery image and flash it.

It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
2018-07-04 01:20:02 +02:00
Maxim Anisimov 7d07bc96b7 ramips: add support for ZyXEL Keenetic Extra II
Specification:
- System-On-Chip: MT7628N/N
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (57600 8n1)
- Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn
- Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac
- USB: Yes 1 x 2.0
- 4x LED, 3x button

The device supports dual boot mode. So we use only first half of flash.

Flash instruction:

The only way to flash OpenWrt image is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin"
   to "kextra2_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-07-04 01:20:02 +02:00
Tobias Schramm faf64056dd ramips: add support for MikroTik RouterBOARD RBM11g
This commit adds support for the MikroTik RouterBOARD RBM11g.

=Hardware=

The RBM11g is a mt7621 based device featuring one GbE port and one
miniPCIe slot with a sim card socket and USB 2.0.

==Switch==

The single onboard Ethernet port is connected the CPU directly.
The internal switch of the mt7621 SoC is disabled.

==Flash==

The device has one spi nor flash chip. It is a 128 Mbit winbond 25Q128FVS
connected to CS0.

==PCIe==

The board features a single miniPCIe slot. It has a dedicated mini SIM
socket and a USB 2.0 port. Power to the miniPCIe slot is controlled via
GPIO9.

==USB==

There are no external USB ports.

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack (center-positive). The input voltage range is 11-32 V.

==Serial port==

The device does have an onboard UART on an unpopulated header next to the
flash chip:

GND: pin 2
 TX: pin 7
 RX: pin 6

Settings: 115200, 8N1

See below illustration for positioning of the header.

0 = screw hole
* = some pin
T = TX  pin
R = RX  pin
G = GND pin

Pinout:
+---------------
|O
|             __
|            /  \
|            \__/
|
|
|
|               +---+
|               |RAM|
| +--+          |   |
| |**|  <- unpopulated header with UART
| |*T|          +---+
| |R*|        +--------+
| |**|        |        |
| |G*|        |  CPU   |
| +--+        |        |
|    +--+     |        |
|    |  |     +--------+
|    +--+  <- flash chip
|O
|       +-----+
|       |     |
|+--+   |     |
||  |   |     |
+---------------------

=Installation=

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM11G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" in the
output directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the
created license file.**

When rebooted the board will try booting via ethernet first. If your
board does not boot via ethernet automatically you will have to attach
to the serial port and set ethernet as boot device within RouterBOOT.

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin"
   initramfs image
2. Connect to ethernet port on board
3. Power on the board
4. Wait for OpenWrt to boot

Right now OpenWrt will be running with a SSH server listening. Now
OpenWrt must be flashed to the devices flash:

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
   to the device using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"

Once the flashing completes the board will reboot. Disconnect from the
devices ethernet port or stop the DHCP/TFTP server to prevent the device
from booting via ethernet again.
The device should now boot straight to OpenWrt.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-07-04 01:20:02 +02:00
Andrey Jr. Melnikov 19c7e950af ramips: move mt7620n i2c_pins definition to right place
Move to i2c pins pinmux node to the pinctrl node.

Fixes: a0685deec4 ("ramips: Add i2c support for mt7620n")

Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
[fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 18:39:57 +02:00
Franz Flasch 8375623a06 ramips: add support for TP-Link Archer C2
Specification:

- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond 25Q64BVSIG
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac
- Switch: RTL8367RB Gigabit Switch
- USB: Yes 1 x 2.0

Preparing a TFTP recovery image for initial flashing:

Currently the only method to install openwrt for the first time is via
TFTP download in u-boot. After first install you can use regular updates.
WARNING: This method also overwrites the bootloader partition!

Create a TFTP recovery image:

1) Download a stock TP-Link Firmware file here:
     https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware
2) Extract u-boot from the binary file:
     #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072
3) Now merge the sysupgrade image and the u-boot into one binary:
     #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin

The resulting image can be flashed via TFTP recovery mode.

Flash instructions:

1) To flash the recovery image, start a TFTP server from IP address
   192.168.0.66 and serve the recovery image named
   ArcherC2V1_tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS/Reset button
   and power it up. Keep pressing the WPS/Reset button for 10 seconds.
   It will try to download the recovery image and flash it.

It can take up to 20-25 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Franz Flasch abb7524683 ramips: fix ZyXEL Keenetic Viva switch config
The rtl8367b driver never supported a mdio property and it is quite
likely that the switch never worked for the board.

Use the mii-bus property instead to manage the switch via a mdio bus.

Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Chuanhong Guo ed40173dfc ramips: Add support for Phicomm K2G
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA.
- UART: 1 x UART on PCB - 57600 8N1

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-06-21 22:00:02 +02:00
Tobias Schramm 5684d08741 ramips: Add support for Mikrotik RouterBOARD RBM33g
This commit adds support for the Mikrotik RouterBOARD RBM33g.

=Hardware=

The RBM33g is a mt7621 based device featuring three gigabit ports, 2
miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male
onboard RS-232 serial port. Additionally there are a lot of accessible
GPIO ports and additional buses like i2c, mdio, spi and uart.

==Switch==

The three Ethernet ports are all connected to the internal switch of the
mt7621 SoC:

port 0: Ethernet Port next to barrel jack with PoE printed on it
port 1: Innermost Ethernet Port on opposite side of RS-232 port
port 2: Outermost Ethernet Port on opposite side of RS-232 port
port 6: CPU

==Flash==

The device has two spi flash chips. The first flash chips is rather small
(512 kB), connected to CS0 by default and contains only the RouterBOOT
bootloader and some factory information (e.g. mac address).
The second chip has a size of 16 MB, is by default connected to CS1 and
contains the firmware image.

==PCIe==

The board features three PCIe-enabled slots. Two of them are miniPCIe
slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2).
Each of the miniPCIe slots is connected to a dedicated mini SIM socket
on the back of the board.

Power to all three PCIe-enabled slots is controlled via GPIOs on the
mt7621 SoC:

PCIe0: GPIO9
PCIe1: GPIO10
PCIe2: GPIO11

==USB==

The board has one external USB 3.0 port at the rear. Additionally PCIe
port 0 has a permanently enabled USB interface. PCIe slot 1 shares its
USB interface with the rear USB port. Thus only either the rear USB port
or the USB interface of PCIe slot 1 can be active at the same time. The
jumper next to the rear USB port controls which one is active:

open: USB on PCIe 1 is active
closed: USB on rear USB port is active

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack. The input voltage range is 11-32 V.

=Installation=

==Prerequisites==

A USB -> RS-232 Adapter and a null modem cable are required for
installation.

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM33G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output
directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the created
license file.**

Serial settings: 115200 8N1

The installation is a two-step process. First the
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted
via tftp:

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin"
   initramfs image
2. Connect to WAN port (left side, next to sys-LED and power indicator)
3. Connect to serial port of board
4. Power on board and enter RouterBOOT setup menu
5. Set boot device to "boot over ethernet"
6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server
   allows dynamic bootp)
6. Save config
7. Wait for board to boot via Ethernet

On the serial port you should now be presented with the OpenWRT boot log.
The next steps will install OpenWRT persistently.

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device
   using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin"

Once the flashing completes reboot the router and let it boot from flash.
It should boot straight to OpenWRT.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00
Deng Qingfang feb0a0bf22 ramips: fix Newifi D1 mtd partition
Newifi D1 has 32 MiB flash, so the firmware partition size should be 0x1fb0000

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-06-21 06:54:42 +02:00
INAGAKI Hiroshi 189815462c ramips: add support for ELECOM WRC-1167GHBK2-S
ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
  - MediaTek MT7615D
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 2x keys
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin"
2. Connect the computer to the LAN port of WRC-1167GHBK2-S
3. Connect power cable to WRC-1167GHBK2-S and turn on it
4. Access to "http://192.168.2.1/details.html" and open firmware
update page ("手動更新(アップデート)")
5. Select the factory image and click apply ("適用") button
6. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 20:46:21 +02:00
Maxim Anisimov 8956eb502d ramips: add support for TP-Link TL-WR842N v5
TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and
non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 7x LED, 2x button, power input switch

Flash instruction:

The only way to flash OpenWrt image in wr842nv5 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-06-16 10:08:51 +02:00
lbzhung 291e34edff ramips: fix mt7688 watchdog register base addr
I found mt7688 watchdog not working. The watchdog registers are identical
for mt7621 and mt7628/mt7688. The first watchdog related register is at
0x10000100, the last one - a 16bit sized - at 0x10000128.

Set the correct register address and size in the dtsi file to get the
watchdog working.

Signed-off-by: lbzhung <gewalalb@gmail.com>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-16 10:08:51 +02:00
INAGAKI Hiroshi a32c06f44d ramips: add support for I-O DATA WN-GX300GR
I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek
MT7621S.

Specification:

- MT7621S (1-Core, 2-Threads)
- 64 MB of RAM
- 8 MB of Flash (SPI)
- 2T2R 2.4 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 115200 bps (U-Boot, OpenWrt)

Flash instruction using initramfs image:

1. Connect serial cable to UART header
2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR"
and place it in the TFTP directory
3. Set the IP address of the computer to 192.168.99.8, connect to the
LAN port of WN-GX300GR, and start the TFTP server on the computer
4. Connect power cable to WN-GX300GR and turn on the router
5. Press "1" key on the serial console to interrupt boot process on
U-Boot, press Enter key 3 times and start firmware download via TFTP
6. WN-GX300GR downloads initramfs image and boot with it
7. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-GX300GR
8. Wait ~150 seconds to complete flasing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-08 09:56:27 +02:00
Rosen Penev 289b2f5e85 ramips: mt7621: Fix some cosmetic DTC warnings
Node /cpus/cpu@0 has a unit name, but no reg property
Node /cpus/cpu@1 has a unit name, but no reg property
Node /cpuintc@0 has a unit name, but no reg property
Node /cpuclock@0 has a unit name, but no reg property
Node /sysclock@0 has a unit name, but no reg property
Node /pcie@1e140000/pcie0 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie0 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie1 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie1 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie2 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie2 missing bus-range for PCI bridge

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-06-08 09:31:37 +02:00
Kevin Darbyshire-Bryant 8110bf18f4 ramips: mir3g dts define usb port Vcc volt regulator GPIO
Define USB port power on/off GPO as voltage regulator type instead of
exposing as a normal GPIO.

The GPO is now controlled by the USB driver via the voltage regulator
definition.  The regulator is of fixed output type (5V for USB) hence the
GPO switches power on/off to USB pin 1 (Vcc)

USB port power is enabled on driver load and disabled on driver unload.

Enable kernel support for fixed voltage regulator types on mt7621.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-08 09:31:36 +02:00
John Crispin 64878a5616 Revert "ramips: improve interrupt mapping"
This reverts commit 5f7396ebef.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:11 +02:00
John Crispin 1d3c286381 Revert "ramips: Fix WiFi after 5f7396ebef09b224edf08b0bda113613a42f0928"
This reverts commit 02f815d190.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:41:51 +02:00
Rosen Penev 976c27f2dd ramips: Fix a few other GnuBee DTS differences
I was carrying a local commit that added the sdhci stuff and missed it
as a result.

Also fix the rgmii3 thing in the PC2 DTS file as that's bogus and causes
a dmesg warning that it's bogus.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-30 06:35:24 +02:00
Rosen Penev 02f815d190 ramips: Fix WiFi after 5f7396ebef
That commit exposed a bug in the DTS files used by mt7621 where the wrong
reg value for pcie1 (and potentially pcie2) was being used. This was
causing WiFi failures for interfaces in pcie1.

eg. 2.4GHz working but not 5GHz.

As all of these dts entries are already specified in mt7621.dtsi, remove
them.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-30 06:33:56 +02:00
Rosen Penev 8c818fa1f0 ramips: Fix up GnuBee PC1 DTS file a little
There's nothing connected to i2c on this board, so remove it.

Also edited the gpio group to match the PC2 as they're the same.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-24 08:57:33 +02:00
Matthias Badaire 52809db544 ramips: fix to mt7620a and add support for i2c on WD03
There was an error on initial commit, the proper soc is mt7620n (which is
more limited than mt7620a). Moreover, there is a battery management
controller connected to the i2c port of the mt7620n. I have a small piece
of i2c code to get battery level coming.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-22 21:02:01 +02:00
David Bauer 35d00d9a41 ramips: fix Archer C50v3 LED mapping
This commit fixes the wrong LED mapping of the Archer C50 v3.
Commit was tested with an EU device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-22 20:34:14 +02:00
YuheiOKAWA d91953cb53 ramips: add support for YUKAI Engineering Inc. BOCCO
BOCCO is a communication robot provided by YUKAI Engineering Inc.

SoC: MT7620A
MEM: 256MB
Flash: 8MB
NAND: 512MB (non support)
Include Sound DAC and AMP.
No Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
2018-05-18 11:19:00 +02:00
Matthias Badaire a0685deec4 ramips: Add i2c support for mt7620n
I2c is supported on mt7620n like on mt7620a when checking the datasheet

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-15 06:39:46 +02:00
NeilBrown 5f7396ebef ramips: improve interrupt mapping
As the Interrupts for the PCI adapters are listed in
devicetree we shouldn't need to have them explicit in the code.

The simplest way to do this is to use of_irq_parse_and_map_pci()
and specify an interrupt-map which identifies the different
PCI hosts by bus/slot numbers.
This has the advantage that the hwirq number are mapped to virq
numbers for us, so the ugly hack can go.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:23:59 +02:00