Commit Graph

18975 Commits (45ae5c2de3491ed5db9695d21faebf95b3b41c56)

Author SHA1 Message Date
Piotr Dymacz 54b1be5f91 ar71xx: image: simplify Embedded Wireless definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz a679a45f0e ar71xx: image: generic: use simply expanded variables
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz 3bc017fa3c ar71xx: image: generic: clean up trailing whitespace
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Ding Tengfei e07014e70b ar71xx: add support for COMFAST CF-E355AC v2
COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9886.

Short specification:

- 2x 10/100 Mbps Ethernet, with PoE support
- 128MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a, WAVE 2
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[updated kernel config for both boards]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Sven Eckelmann b1d57dadb2 ar71xx: disable 40Mhz refclk for QCA953x
The "QCA9531 v2.0 802.11n 2x2 2.4 GHz Premium SOC for WLAN Platforms"
datasheet (80-Y7991-1 Rev. C - October 2014) doesn't specify support for a
40 Mhz reference clock. The register description for "Bootstrap Options"
(page 31) defines following states for the bit 4 (REF_CLK):

* 0 - CLK25 (default)
* 1 - (reserved)

Devices like the TP-Link CPE210 v2 has this bit set to 1 but is using a 25
Mhz reference clock. OpenWrt is still interpreted this bit as 40 Mhz and
then break the bootup of the system due to this incorrect interpretation.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[refreshed patches]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Peng Zhang d8e6c3f6d9 ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2
WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334.

Specification:

- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11)
- 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11)
- 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 1x USB 2.0
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (J5) and LEDs (J13) headers on PCB

WHQX E600G is based on Qualcomm QCA9531.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB

WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11)
- 2x 10/100 Mbps Ethernet
- 6x LED (1x RGB, 5 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-12 V)
- UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB

Important notice:

First version of these boards are using different mtd layout, with ART
data at the end. You should not use v2 images on v1 board because it
will result in lost of ART data!

Flash instruction (using U-Boot CLI and tftp server):

1. Configure PC with static IP 192.168.1.10 and tftp server.
2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
3. Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
4. Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

1. Configure PC with static IP 192.168.1.xxx(2-254)/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
3. Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[reworked: image generation code, mach-* files, commit description,
fixed minor code style issues, rebased on master]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz fc43e7a6e0 ar71xx: fix typos and indentation in Kconfig.openwrt
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Kyson Lok bb1df2d75b ar71xx: include vendor name for GL iNet products
This patch include GL.iNet vendor name in the
machine name for GL.iNet vendor products.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
2018-02-22 18:53:22 +01:00
Kyson Lok 9dbfd8e9df ar71xx: uniform GL iNet products mach name
The mach name of GL AR150 and GL AR300 is inconsistent
with other products.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
2018-02-22 18:53:21 +01:00
Roman Yeryomin 6b6dc2b3e3 ramips: mt7621: fix usb init
In 4.14 reg-names is required to identify resources.
Otherwise init fails with:

[    5.900501] xhci-mtk 1e1c0000.xhci: invalid resource
[    5.910499] xhci-mtk: probe of 1e1c0000.xhci failed with error -22

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-02-22 17:25:38 +01:00
Felix Fietkau 94a3af88f3 octeontx: remove lots of bogus kernel config overrides
Some of them break when building with all modules enabled

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-22 13:12:17 +01:00
Tim Harvey 9f2c769a59 kernel: add missing symbol
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey d83ce3ff50 octeontx: remove undefs of CONFIG_NET_VENDOR_*
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey b63b18dffc octeontx: remove unnecessary CONFIG_DEBUG_INFO
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey ef627cb0f5 octeontx: add fpu support
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey 10280d9e22 octeontx: remove CFLAGS
You should not define CFLAGS for the toolchain as this will also leak
into other targets if they share the same toolchain.

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey c0470e7917 octeontx: add FAT FS support to kernel
The CN80XX Boot firmware uses an embedded FAT12 filesystem. For some reason
busybox can't mount this unless its enabled static in the kernel.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey 4294b79e0a octeontx: add USB_PCI support
The CN80XX XHCI is supported through PCI

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Koen Vandeputte efb362cd93 imx6: disable dma on uart
When this target got updated to 4.14, this patch got removed to
re-evaluate if it was still needed.

Extensive testing now shows this issue is still present.
Let's re-add the patch to fix it for now.

As the uart bus is very low bandwidth .. performance impact is negligible.

Boot log:

[   22.513051] imx-uart 2020000.serial: DMA transaction error.
[   22.522721] imx-uart 2020000.serial: DMA transaction error.

As a sidenote:
The patch mentiones an issue with RS485, but the bootlog
errors above were recorded with the uart ports in standard RS232 mode.

Compile/Run-tested on imx6/GW5200

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-22 12:46:49 +01:00
Koen Vandeputte aad1f11efe kernel: refresh patches
Some fuzz was introduced due to the netfilter-offload series

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-22 12:46:25 +01:00
Felix Fietkau 9d2a23780e kernel: avoid stripping retpoline flag with CONFIG_MODULE_STRIPPED
Fixes kernel warning when loading modules

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:55:52 +01:00
Felix Fietkau 820f030998 netfilter: add a xt_FLOWOFFLOAD target for NAT/routing offload support
This makes it possible to add an iptables rule that offloads routing/NAT
packet processing to a software fast path. This fast path is much
quicker than running packets through the regular tables/chains.

Requires Linux 4.14

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:42 +01:00
Felix Fietkau 1033356442 kernel: backport netfilter NAT offload support to 4.14
This only works with nftables for now, iptables support will be added
later. Includes a number of related upstream nftables improvements to
simplify backporting follow-up changes

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:42 +01:00
Felix Fietkau b7265c59ab kernel: backport a series of netfilter cleanup patches to 4.14
Preparation for backporting upstream NAT offload support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:42 +01:00
Felix Fietkau 8a59f9590e ramips: fix MT7621 switch driver IRQ storm on init with linux 4.14
The hardware emits some interrupts while initializing and handling them
can mess up the state or cause infinite loops.
Fix this by disabling IRQs during init and re-enabling them afterwards

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 14:46:45 +01:00
Felix Fietkau 0405205140 kernel: fix MIPS GIC clock source counter width (affects MT7621)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 14:46:45 +01:00
Felix Fietkau 79f9cadd00 ramips: fix MT7621 PCI driver on 4.14
The .map_irq hook can now be called after init.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 14:46:45 +01:00
Felix Fietkau 9595a9e8d3 kernel: fix return value of usb_xhci_needs_pci_reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-20 22:29:32 +01:00
Felix Fietkau c38fb58576 kernel: fix disabling common usb quirks on 4.14
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-20 22:19:41 +01:00
INAGAKI Hiroshi e1d4aa36b0 ramips: add support for Tama W06
Tama Electric Axing W06 is a 2.4 GHz band 11n router, based on Mediatek
MT7688AN.

Specification:

- MT7688AN (575 MHz)
- 64 MB of RAM (DDR2 SDRAM)
- 16 MB of Flash (SPI)
- 1T1R 2.4 GHz
- 1x 10/100/1000 Mbps Ethernet
- 4x LEDs (GPIO connected: 3), 1x button
- 1x USB 2.0 Type-A (host)
- UART header on PCB (GND, RX, TX, Vcc from RJ45 side)

Flash instruction using sysupgrade image:
1. Connect micro-USB cable for power supply into W06 and turn on the
router
2. Connect to wifi with SSID "tama-*" with password. Complete SSID and
password are listed on the back of the router
3. Access to 192.168.1.1 and login with user name "admin" and password
empty
4. In firmware update(ファームウェア更新) page, click "参照" button
and click "ブラウザー" button to open file browser, select the
sysupgrade image and press OK button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-02-20 19:25:17 +01:00
Mathias Kresin cb741654e5 ramips: improve GnuBee Personal Cloud Two support
Use the generic board detection for the GnuBee Personal Cloud Two
instead of the target specific one as all recent additions are doing.

Fixup the pinmux to set all pins used as GPIO to the function GPIO.
Request pins where used.

Drop the i2c from the dts. There is nothing connected. While at it fix an
indentation issue and use references instead of duplicating the whole
node path.

Use the same switch config as for the GB-PC1 and drop the led trigger for
the not supported IP1001 phy connected to second rgmii.

Fixes: c60a21532b ("ramips: Add support for the GnuBee Personal Cloud Two")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin c330408ea9 ramips: use generic board detection for D-Link DAP-1522 A1
Use the generic board detection for the D-Link DAP-1522 A1 instead of the
target specific one as all recent additions are doing.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Hauke Mehrtens 6eaf8b3d89 lantiq: kernel 4.14: update dts files
Updated the devicetree source files to make use of the following
upstreamed drivers:

 - xrx200 ethernet phy
 - reset controller unit
 - dwc2
 - fpi

Use our custom xrx200 ethernet phy compatible to support boards, which
have switched the vr9 revision during lifetime, with a single devicetree
source file.

By switching to the dwc2 driver + usb phy framework, we don't need to used
our custom gpio power patch and can use a fixed regulator instead.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin f519fea4c6 lantiq: kernel 4.14: cleanup dts files
Move common used parts to dtsi. Add labels to nodes and reference nodes
via labels in dts files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin 82ae68be70 lantiq: kernel 4.14: fix usb
On danube the USB0 registers are at 1e101000 similar to all other lantiq
SoCs.

On Danube and AR9 the USB core is connected to the AHB bus, hence we need
to enable the AHB Bus as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin 2368f7cb78 lantiq: kernel 4.14: autoselect matching vr9 rev firmware
Add a custom xrx200 ethernet phy compatible to load the firmware matching
the vr9 revision without specifing an expected revision.

We have quite a few boards in the tree were later produced ones are using
a more recent vr9. It is impossible to distinguish which revision of the
vr9 is used without opening the case and removing a heatsink for some of
them.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin a48b4ae38b lantiq: kernel 4.14: don't use CPU interrupt controller IPI IRQ domain support
This reverts kernel commit 1eed40043579 ("MIPS: smp-mt: Use CPU interrupt
controller IPI IRQ domain support"). With the patch applied, the kernel
hangs during boot if SMP is active.

The Lantiq IRQ controller gets registered first and it directly handles
the MIPS native SW1/2 and HW0 - HW5 IRQs. It looks like this controller
already registers IRQ 0 - 7 and the generic driver only gets the following
IRQs starting later.

The upstream discussion can be found at
https://www.linux-mips.org/archives/linux-mips/2017-05/msg00059.html.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin cf53f2180c lantiq: kernel 4.14: select MFD SYSCON for ase
Enable syscon to use it for the RCU MFD on Amazon SE as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Hauke Mehrtens f1d84023cb lantiq: kernel 4.14: update patches and config
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Hauke Mehrtens 5eeaba31b8 lantiq: kernel 4.14: copy patches, config and dts files
This just copies the patches, configuration and dts files into the
directories hich are used for kernel 4.14.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-20 19:25:17 +01:00
Mathias Kresin f8a6987cd1 lantiq: make dts files and kernel config kernel version specific
Move the devicetree source files to a kernel specific directory in
preparation of adding kernel 4.14 support.

Rename the subtarget kernel config files to match a specific kernel
version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin 627a28eb09 lantiq: rename gphy firmware
Rename the gphy firmware to match the name requested by kernel 4.14 and
update the devicetree source files to use the new name.

Update the u-boot lantiq Makefile to be compatible with the new names as
well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Michael Heimpold 240e1e3fe4 mxs: drop support for 4.9
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2018-02-20 13:25:00 +01:00
Michael Heimpold 4812a3d1b5 mxs: enable LRADC driver
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2018-02-20 13:24:52 +01:00
Zoltan HERPAI 0a2494545e mxs: bump to use 4.14 by default
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-02-20 13:24:46 +01:00
Zoltan HERPAI 1bbd66c4fc mxs: add support for 4.14
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-02-20 13:24:43 +01:00
John Crispin ba5f700d7f kernel: ar83xx: remove stray leading space
Signed-off-by: John Crispin <john@phrozen.org>
2018-02-20 10:33:47 +01:00
Tan Hong Hui 1263d07b89 kernel: ar83xx: add support to configure per port VLAN priority
Add support to allow for per switch port VLAN priority (PCP) bits
for the ar8327/8337 chip using the swconfig utility.

Tested on Netgear R7800

Signed-off-by: Tan Hong Hui <hhtan72@yahoo.com>
2018-02-20 10:33:34 +01:00
Koen Vandeputte 2f85985da2 kernel: backport pcie enumeration fix to kernel 4.9
This issue is also present in kernel 4.9 starting from 4.9.71
Adapted the patch, as the fixed function is in another location here.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-20 08:32:33 +01:00
Stijn Tintel 858ff4f3e1 Revert "brcm2708: fix sdcard image"
This reverts commit 6c2e1ff80f.

GNU gzip does not fail when the image filename already contains the .gz
extension, this is a problem specific to pigz. Revert the commit, as we
now gzip the image twice.

Reported-by: Martin Schleier <drahemmaps@gmx.net>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-02-19 23:52:45 +01:00
Rafał Miłecki 8651f1149d kernel: backport patches simplifying mtd_device_parse_register code
These 2 patches were recently queued for 4.17.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-02-19 16:01:44 +01:00
Rafał Miłecki eefe02b23f kernel: order mtd backported patches by kernel release
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-02-19 15:28:47 +01:00
Tim Harvey 1188f35a98 imx6: remove support for 4.9
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-19 09:32:43 +01:00
Tim Harvey 8f9668f46c imx6: switch to Linux 4.14
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-19 09:32:43 +01:00
Tim Harvey 3b2708f09c imx6: add support for Linux 4.14
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-19 09:32:43 +01:00
Tim Harvey 3282e7189f kernel: backport dwc pci enumeration fix
Backport of:  http://patchwork.ozlabs.org/patch/860701/

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-19 09:32:43 +01:00
John Crispin cc8921162f kernel: add missing symbols for v4.14
Signed-off-by: John Crispin <john@phrozen.org>
2018-02-19 09:32:43 +01:00
Hauke Mehrtens 47c5415023 brcm2708: Fix compile after adding kernel 4.9.82
Fixes: f621b53951 ("kernel: bump 4.9 to 4.9.82")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-18 19:52:06 +01:00
Hauke Mehrtens b377a908bf x86: Use kernel 4.14 by default
Support for kernel 4.14 was added 2 months ago, make it now the default
kernel to use for the x86 target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Stijn Segers <francesco.borromini@inventati.org>
2018-02-18 19:51:58 +01:00
Stijn Tintel ae42e7c01b kernel: add missing config symbols
They were introduced for arm64 in 4.14.20.

Fixes: 88ba41453d ("kernel: bump 4.14 to 4.14.20")

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-02-18 14:34:00 +01:00
John Crispin 761d45eb87 kernel: add missing symbol
this caused v4.14.20 based builds so fail on aarch64

Signed-off-by: John Crispin <john@phrozen.org>
2018-02-18 09:21:12 +01:00
Stijn Tintel f621b53951 kernel: bump 4.9 to 4.9.82
Refresh patches.
Remove upstreamed patches:
- ar7/002-MIPS-AR7-ensure-the-port-type-s-FCR-value-is-used.patch
- backport/040-crypto-fix-typo-in-KPP-dependency-of-CRYPTO_ECDH.patch
Remove layerscape/819-Revert-dmaengine-dmatest-move-callback-wait-queue-to.patch,
it is superseded by upstream commit 297c7cc4b5651b174a62925b6c961085f04979fd.
Remove pending/650-pppoe_header_pad.patch, it is superseded by
upstream commit 1bd21b158e07e0b8c5a2ce832305a0ebfe42c480.
Update patches that no longer apply:
- ar71xx/004-register_gpio_driver_earlier.patch
- hack/204-module_strip.patch
- pending/493-ubi-set-ROOT_DEV-to-ubiblock-rootfs-if-unset.patch

Fixes CVE-2017-8824.

Compile-tested: ar71xx.
Runtime-tested: ar71xx.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-02-18 02:59:57 +01:00
Stijn Tintel 88ba41453d kernel: bump 4.14 to 4.14.20
Refresh patches.
Remove upstreamed patches:
- backport/080-v4.15-0001-arch-define-weak-abort.patch
- backport/081-v4.15-0002-kernel-exit.c-export-abort-to-modules.patch
Update patch that no longer applies:
pending/493-ubi-set-ROOT_DEV-to-ubiblock-rootfs-if-unset.patch

Fixes CVE-2017-8824.

Compile-tested: octeon, x86/64.
Runtime-tested: octeon, x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-02-18 02:59:48 +01:00
Stijn Tintel 6c2e1ff80f brcm2708: fix sdcard image
The gzip step in the sdcard image build fails because the image filename
already has the gzip extension. This results in an empty image file, to
which the metadata is finally appended.

Remove the .gz extension from the image filename to fix this.

Fixes: e79b096ee1 ("brcm2708: convert to metadata")

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-02-17 21:00:49 +01:00
Evgeniy Didin 4cedd1ddb3 archs38: add HSDK board to network configure scripts
In the initial patch which adds HSDK board there were no update
of network configuration scripts. Without it by default static IP
is set for br-lan and there is no access to internet.
This patch fixes the issue.

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
CC: Alexey Brodkin <abrodkin@synopsys.com>
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John Crispin <john@phrozen.org>
2018-02-17 12:29:55 +01:00
Hauke Mehrtens 6be73c07db sunxi: Add Xunlong Orange Pi Zero Plus
This is based on a patch from armbian:
https://github.com/armbian/build/blob/master/patch/kernel/sunxi-next/sunxi-add-orangepi-zero-plus.patch

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-17 01:15:25 +01:00
Hauke Mehrtens ef73ebbfe2 sunxi: Add Realtek PHY driver or ARM64 devices
The Orange Pi Zero Plus uses a RTL8211E, add the driver for this PHY.
This is probably used on more boards with a Allwinner SoC.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-17 01:15:24 +01:00
Antony Antony 3c24a1d423 sunxi: add support for NanoPi NEO Plus2 board
arm64: allwinner: h5: NanoPi NEO Plus2 DT support
Add initial DT for NanoPi NEO Plus2 by FriendlyARM
    - Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU
    - 1 GB DDR3 RAM
    - 8GB eMMC flash (Samsung KLM8G1WEPD-B031)
    - micro SD card slot
    - Gigabit Ethernet (external RTL8211E-VB-CG chip)
    - 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module)
    - 2x USB 2.0 host ports & 2x USB via headers

Signed-off-by: Antony Antony <antony@phenome.org>
2018-02-17 01:15:24 +01:00
Antony Antony b7a1aa4df2 sunxi: add kernel DT for NanoPi NEO Plus2 board
Linux Kernel upstream commit d73413058

Signed-off-by: Antony Antony <antony@phenome.org>
2018-02-17 01:15:24 +01:00
Mathias Kresin 7a6de6d77a ar71xx: fix sysupgrade syntax error
Fix syntax error introduced with 188328111b ("treewide: move
nand_do_upgrade call to platform_do_upgrade").

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-16 22:56:56 +01:00
Mathias Kresin 188328111b treewide: move nand_do_upgrade call to platform_do_upgrade
Calling nand_do_upgrade() from platform_pre_upgrade() was deprecated
with 30f61a34b4 ("base-files: always use staged sysupgrade").

Update the platform upgrade code to use platform_do_upgrade() for NAND
images as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-16 14:44:02 +01:00
Mathias Kresin c4ac02ffca treewide: remove obsolete sysupgrade watchdog kill
The watchdog kill command was meant for busybox watchdog. Busybox watchdog
was replaced by the procd watchdog mid 2013 with commit df7ce9301a
("busybox: disable the watchdog utility by default"), which makes the kill
command obsolete since quite some time.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-16 14:44:02 +01:00
Zoltan HERPAI eae6003174 sunxi: switch to kernel 4.14
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-02-16 12:20:39 +01:00
John Crispin 6873cf4f63 kernel: add missing symbols
These cause mediatek arm to fail full builds

Signed-off-by: John Crispin <john@phrozen.org>
2018-02-16 10:02:08 +01:00
Roman Yeryomin f4e5880d0f ramips: preliminary support for 4.14
- removed upstreamed patches
- 0901-spansion_nand_id_fix.patch is disabled, not clear if it's needed

Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: John Crispin <john@phrozen.org>
2018-02-15 10:46:39 +01:00
Jo-Philipp Wich dc7a1e8555 ramips: fix reporting effective VLAN ID on MT7621 switches
On MT7621, the REG_ESW_VLAN_VTIM reads are undefined, causing swconfig
to always report `vid: 0` in swconfig show output.

Since a 4K VLAN table is used on this platform, the VLAN ID always
correponds to the actual VLAN table index so provide a specific MT7621
implementation of the get_vid callback which returns the table index
as VLAN ID.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-02-14 16:43:30 +01:00
Jo-Philipp Wich 341b1427fc ramips: properly map pvid for vlans with remapped vid on mt7530/762x switches
Currently, untagged port primary vlan IDs are set to the VLAN table index,
and not the actual VLAN ID, breaking configurations with IDs deviating from
the VLAN index.

Fix the issue by resolving the per-port pvid property to the target VLAN ID
value before committing to the hardware.

Fixes FS#991, FS#1147, FS#1341

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-02-14 16:43:30 +01:00
Jo-Philipp Wich bb4002c79d ramips: don't clobber vlans with remapped vid on mt7530/762x switches
Avoid overwriting vlan entries with remapped vid in later iterations of
the vlan enumeration loop of mt7530_apply_config().

Fix the problem by refactoring the code to first reset the entire table,
then reprogram only vlans with members to prevent overwriting configured
vlans with unconfigured ones.

Fixes FS#1147, FS#1341

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-02-14 16:43:29 +01:00
Jo-Philipp Wich b9aca834e8 at91: fix image building with CONFIG_TARGET_MULTI_PROFILE
The current image build code has a number of race conditions and interface
contract violations in the custom image build steps:

 - Build/install-zImage, solely used by at91, relies on $(PROFILE_SANITIZED)
   which is not available when building with CONFIG_TARGET_MULTI_PROFILE

 - Build/at91-sdcard, which may run concurrently, creates scratch files at
   fixed locations and manipulates target files directly which can lead
   to file corruption and other unexpected failures

Rename the install-zImage macro to at91-install-zImage and move it to the
at91 image Makefile since this target is the sole user. Also utilize "$@"
as output file name and switch the usage of $(PROFILE_SANITIZED) to
$(DEVICE_NAME) in order to fix naming under multi profile builds.

Fix the at91-sdcard macro to construct scratch file paths relative to "$@",
which is guaranteed to be unique and store the final artifact output in "$@"
as well, instead of inside $(BIN_DIR). The generic image build code takes
care of moving a build steps "$@" output to the final destination in a
concurrency-safe manner.

Finally remove the broken install-zImage from the generic image-commands
Makefile.

Fixes: d7a679a036 ("at91: Install zImage.")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-02-14 15:47:16 +01:00
John Crispin 7762c07c88 mediatek: bump to v4.14
This drops support for all the !emmc EVB and adds banannaPi-R2
Also drop mtkhnat until the nftables offoad driver is ready

Signed-off-by: John Crispin <john@phrozen.org>
2018-02-14 11:27:50 +01:00
Dongming Han 04d3308b62 ipq806x: add support for GL.iNet GL-B1300
This patch adds support for GL.iNet GL-B1300

Specification:
- SOC:        IPQ4028 / QCA Dakota
- RAM:        256 MiB
- FLASH:      32 MiB
- ETH:        Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB:        1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1:      Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2:      Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT:      one reset and one WPS button
- LEDS:       3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART:       1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1

Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
  192.168.1.2 have that file.
- the wifi led will be flashing when writing image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2018-02-14 09:40:32 +01:00
Evgeniy Didin d55a05fc9e archs38: add HSDK board
Synopsys DesignWare HSDK (which stands for ARC HS
Development Kit) is the latest and greatest development
platform that sports quad-core ARC HS38 in real silicon.

Most noticeable features of the board are:
 * Quad-core ARC HS38 CPU running at 1GHz
 * 4Gb of DDR
 * Built-in Vivante GPU (well supported via open source
   Etnaviv drivers)
 * Built-in Wi-Fi/Bluetooth module (RedPine RS-9113)

And as usual we have:
 * [micro] SD-card slot
 * 2 USB 2.0 ports
 * 1Gbit Ethernet port
 * Built-in Digilent JTAG probe
 * Serial port accessible via micro-USB port

For more information about HSDK board visit:
https://www.synopsys.com/dw/ipdir.php?ds=arc-hs-development-kit

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
CC: Alexey Brodkin <abrodkin@synopsys.com>
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John Crispin <john@phrozen.org>
2018-02-14 07:54:24 +01:00
Evgeniy Didin 0a1a672e95 archs38: switch to kmod-usb2
We have managed to get USB 2.0 working good enough
on all archs38 platforms so we're ready to switch
to much faster USB 2.0.

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
CC: Alexey Brodkin <abrodkin@synopsys.com>
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John Crispin <john@phrozen.org>
2018-02-14 07:54:24 +01:00
Kevin Darbyshire-Bryant 0b4e3b1bed generic: swconfig: reduce lock duration on sysfs files
sysfs attributes 'port_mask' & 'speed_mask' held locks whilst doing
mundane tasks such as sprintf.  Refactor code to reduce length of time
locks are held unnecessarily.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-02-14 07:54:24 +01:00
Kevin Darbyshire-Bryant eb8fbc4318 generic: swconfig: add mode led attribute
Add sysfs 'mode' attribute to swconfig controlled LEDs.

swconfig 'link state' LEDs blink in the presence of port traffic.  This
behaviour becomes more obvious as switches start to support
get_port_stats() e.g. commits 0369e35891,
3056d09b40,
4ddbc43cc1,
4d8a66d934.

This blinking can be confusing/distracting if the switch has other LEDs
used to indicate traffic.  Provide a 'mode' sysfs attribute that
controls the blink on traffic behaviour.

mode - either "none" (LED is off) or a space separated list of one or more:

link: LED's normal state reflects whether the link is up (has carrier) or not
tx:   LED blinks on transmitted data
rx:   LED blinks on receive data

Note that 'link' considers any port speed mask that may be applicable.
e.g. if an LED is configured to indicate 1Gbit link speed and mode is
set to 'link rx tx' but the port is connected at 100Mbit then the LED
will not light or blink. A mode of 'tx rx' will blink in the presence of
traffic only if the port matches the rate (if configured)
This maintains compatibility with existing behaviour.

Attribute is 'link tx rx' by default for backwards compatible behaviour.

Many thanks to Thibaut Varene for providing a more sensible led_event
routine after I had mangled the original, and other coding style hints.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Thibaut VARENE <hacks@slashdirt.org>
2018-02-14 07:54:24 +01:00
Hauke Mehrtens 0bd5aa89fc mvebu: Migrate uci config to new PCIe path
The name of the PCIe controller node in device tree changed between
kernel 4.9 and kernel 4.14. Migrate the configuration when an update
from kernel 4.9 to 4.14 or back is done to the new name to make
the existing wifi configuration compatible with the new names.

This replaces the "pcie-controller" part with "pcie" on all nodes if the
file exists in sys fs.

This is not done in the uci-defualts, because they are getting executed
to late in the boot process. The kernel module gets loaded before the
uci-defaults scripts are executed. When the mwlwifi driver gets loaded
it will trigger an event via hotplug to detect new devices and as the
paths are not in the uci configuration they will be added again.
When the migration is done before the script will detect that they are
already there.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-13 22:30:59 +01:00
Hauke Mehrtens 4ccad92229 mvebu: Add support for kernel 4.14
Add support for kernel 4.14 to the mvebu target.

This also replaces the old sfp and phylink patches with new versions
from Russell's clearfog-4.13 branch
http://git.arm.linux.org.uk/cgit/linux-arm.git/log/?h=clearfog-4.13

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-13 22:29:56 +01:00
Hauke Mehrtens 47106f55e0 mvebu: move files to files-4.9 and files-4.4 folder
This is needed to prevent copying it into kernel 4.14.
These device tree files are already integrated into kernel 4.14 and we
would like to use the upstream versions only.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-13 22:24:56 +01:00
Hauke Mehrtens 87b35c16ad kernel: ubifs: create use file system format 4 by default
Instead of creating an ubifs file system with format version 5 by
default on empty UBI volumes use the older format 4 by default. This
will make it possible to mount these file systems also on older kernel
versions.

When a user wants to do a sysupgrade from kernel 4.14 to kernel 4.9 the
old kernel has to read the file system created by the more recent kernel
which currently does not work for ubifs.

This fixes the problem by creating file systems which are compatible
with older kernel versions by default.
Kernel 4.14 will still be able to read and write UBI FS file system
version 5, it will just not be used when a ubifs partition is created
implicitly on an empty UBI volume.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-13 22:24:56 +01:00
Hauke Mehrtens 970cbfc307 kernel: Add missing config options
These were found when compiling the new octeontx target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-13 22:24:02 +01:00
Jonas Gorski 0f063f8ac7 brcm63xx: drop root parameter from cmdline
The root= parameter overrides the automatic rootfs detection by partition
name, so drop it. Fixes boot from flash after renumeration changes of
partitions due to parser changes.

Fixes FS#1350.

Fixes: a27d59bb42 ("brcm63xx: switch to new partition layout specification")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-13 13:17:26 +01:00
Stefan Lippers-Hollmann 4baffa02ce ipq806x: switch to full dual-boot for the nbg6817 sysupgrade support
Instead of writing to the currently booted partition set, this
implements full dual-boot support for sysupgrade by always writing to
the other, currently inactive, partition set and toggling the dualflag
after a successful flash.

The currently active/ booted partition set is determined by parsing
/proc/cmdline for its rootfs parameter (supplied by the DTS), instead
of reading from the 0:DUAL_FLAG mtd, in order to prevent (potentially)
bricking both partition sets.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-02-13 12:45:00 +01:00
Stefan Lippers-Hollmann 42fe7b3bbe ipq806x: request the first free loop device dynamically for the nbg6817 sysupgrade
Instead of hardcoding /dev/loop0, it's safer to query for the first
free loop device and assign that dynamically. While /dev/loop0 is a
reasonable assumption immediately following "losetup --detach-all",
detaching the mounted overlay is no longer strictly necessary once
dual-boot support has been added for the nbg6817.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-02-13 12:45:00 +01:00
Stefan Lippers-Hollmann b36cf0be30 ipq806x: use absolute the device path in $kernel for the nbg6817 sysupgrade
Harmonize the variable usage for $kernel and $rootfs to always contain
the full device path, instead of just its basename.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-02-13 12:45:00 +01:00
Luis Araneda 887925b098 ipq806x: support new location of USB PHY kernel module
PHY drivers were grouped into vendor specific directories
by upstream commit 0b56e9a7e8358e59b21d8a425e463072bfae523c

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-02-13 11:56:40 +01:00
Julien Dusser 8dd455e3c4 ar71xx: add more registers to ar71x_regs.h
Add more registers and flags to ar71x_regs.h for QCA955x and QCA956x
SoCs. Values come from Qualcomm Atheros u-boot code.

Patches can be merged into
622-MIPS-ath79-add-more-register-defines-for-QCA956x-SoC.patch

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2018-02-13 11:20:58 +01:00
George Hopkins 13f9e40602 ramips: add support for D-Link DAP-1522 A1
D-Link DAP-1522 is a wireless bridge/access point with 4 LAN
ports and a dual-band wireless chipset.

Specifications:
- Ralink RT2880
- 32 MB of RAM
- 4 MB of Flash
- 4x 10/100/1000 Mbps Ethernet (RTL8366SR)
- 802.11abgn (RT2850)

Flash Instructions:
1. Download lede-ramips-rt288x-dap-1522-a1-squashfs-factory.bin
2. Open the web interface and upload the image

Signed-off-by: George Hopkins <george-hopkins@null.net>
2018-02-13 11:18:07 +01:00
George Hopkins 5c7a58764e kernel: mtdsplit: split by WRG header
Support splitting WRG images, which can be found in older
D-Link devices.

Signed-off-by: George Hopkins <george-hopkins@null.net>
2018-02-13 11:16:49 +01:00
John Crispin 6e7357097f kernel: add missing symbol
Signed-off-by: John Crispin <john@phrozen.org>
2018-02-13 10:55:46 +01:00
Karl Palsson b2a5f7683b ar71xx: Add eTactica EG-200 support
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.

Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.

Flash instruction:
    Original firmware is based on OpenWrt.
    Use sysupgrade image directly in vendor GUI.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-02-13 10:01:53 +01:00