Commit Graph

18975 Commits (45ae5c2de3491ed5db9695d21faebf95b3b41c56)

Author SHA1 Message Date
INAGAKI Hiroshi 192b5a7710 ramips: use new image build code for WHR-G300N
The tftp.bin image for Buffalo WHR-G300N was not built, so I was fixed
it after rewriting to new image build code. And the code for
factory-EU.bin was broken, so I deleted it.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-02-13 10:01:53 +01:00
John Crispin 5555545494 mediatek: remove the CPU_SUBTYPE
Signed-off-by: John Crispin <john@phrozen.org>
2018-02-13 10:01:53 +01:00
Koen Vandeputte 5adf16b492 cns3xxx: remove linux 4.9 support
- Remove kernel 4.9 support
- Apply specific 4.14 changes directly to source
- Refreshed all

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-13 10:01:53 +01:00
John Crispin 1fe888554c kernel: add missing symbol for v4.14
Signed-off-by: John Crispin <john@phrozen.org>
2018-02-13 10:01:52 +01:00
Tim Harvey fc03b3aa16 octeontx: add support for OCTEON TX target
The Cavium OCTEON TX is an ARM 64-bit SoC leveraging CPU cores and
periperhals from the Cavium ThunderX SoC.

This initial support provides a 4.14 kernel and kernel+initramfs that is
bootable on the Gateworks Newport GW630x as well as the Cavium sff8104
reference board.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-13 10:01:52 +01:00
Michael Heimpold f34b118b35 mxs: rename files to files-4.9
The Device Tree file for I2SE Duckbill boards was updated upstream.
Let's use the upstream version for upcoming kernel 4.14 by keeping
our current version for v4.9 still around.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2018-02-13 10:01:52 +01:00
Rosen Penev c60a21532b ramips: Add support for the GnuBee Personal Cloud Two
The GnuBee Personal Cloud Two crowdfunded on https://www.crowdsupply.com
It is a low-cost, low-power, network-attached storage device.

Specifications:

- SoC: MediaTek MT7621AT
- RAM: DDR3 512 MB
- Flash: 32 MB
- Six SATA ports for 3.5" Drives
- One SDcard
- One USB 3.0
- Two USB 2.0
- Gigabit Ethernet: Three Ports
- UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
- Three GPIOs available on a pin header

Flash instructions:

The GnuBee Personal Cloud Two ships with libreCMC installed.
libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
As such one can upgrade using the webinterface or sysupgrade.

Das U-Boot has multiple options for recovery or updates including :

- USB
- http
- tftp

Errata:
- While there are three ethernet ports, the third requires support for
  the second GMAC. This will come in kernel 4.14.
- The first hard drive slot has a clearance issue with the two fan
  headers. Workaround is to pull the headers out and connect the pins to
  jumper wires.
- Using this device as a NAS is problematic with the 4.9 kernel as many
  /dev/sdX reads throw silent errors. The current theory behind this is
  some kind of unhandled DMA mapping error in the kernel. This is not an
  issue with kernel 4.4.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-02-13 10:01:52 +01:00
Yangbo Lu f226e652f6 layerscape: fix call trace of pfe module removing
Updated pfe kernel patch to clean up iounmap(pfe->ddr_baseaddr).
pfe->ddr_baseaddr was got through phys_to_virt() not ioremap(),
so iounmap() for pfe->ddr_baseaddr should be removed.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:51 +01:00
Yangbo Lu 35a61fef56 layerscape: fix DPAA2 QDMA issue
This patch is to reverse a upstream dmatest patch for now
which is causing DPAA2 QDMA test issue.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:51 +01:00
Yangbo Lu f78168be62 layerscape: add a make menuconfig known issue in README
This patch is to add a known issue of make menuconfig
in README file. This is also a common issue for OpenWrt.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:51 +01:00
Yangbo Lu 7b93a18b10 layerscape: fix type for kernel 4.9 dpaa2_mac_get_stats() function
This patch changes the declarations of ndo_get_stats64 handlers
to the previous struct rtnl_link_stats64 * return type instead of
the mainline void return.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:51 +01:00
Yangbo Lu 94698fa6ab layerscape: update README
Tis patch is to fix up some descriptions in README.
Per-device rootfs had been supported, and a known issue
had been found. These also should be updated accordingly.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:51 +01:00
Yangbo Lu 1079a03886 layerscape: support ubifs rootfs
Some layerscape devices (ls1012ardb/ls1012afrdm/ls1046ardb/ls1088ardb)
were using ext4 rootfs because there were issues using squashfs.
This patch is to drop using ext4 rootfs and use ubifs rootfs instead
which is more proper for SPI-NOR flash.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:51 +01:00
Yangbo Lu 841ad46b90 layerscape: remove USB configs for 64-bit
Removed USB configs for 64-bit device since they're
already in kmod package.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:50 +01:00
Yangbo Lu 6e9a5f4db4 layerscape: remove USB and TI specific configs for 32-bit
This patch is to remove USB configs for 32-bit device since
they're already in kmod package. Also removed TI platform
specific configs.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:50 +01:00
Yangbo Lu 1a28100e68 layerscape: update patches-4.9 to LSDK1712
Patches changes
- Updated patches-4.9 to NXP LSDK1712 linux-4.9.
- Merged changes of patch 303 into integrated patch 201.
- Split changes of patch 706 into dpaa part and dpaa2
  part, and merged these changes into integrated patches
  701 and 705.
- Removed patch 819 since ehci-fsl driver could be compiled now.
- Refreshed these patches.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:49 +01:00
Yangbo Lu 5f36f3193f layerscape: update build guide in README
Added package feeds updating and installing in build guide
of README.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-02-13 10:01:49 +01:00
Henryk Heisig a338491a30 ar71xx: add support for TP-Link RE355
This device is identical as TP-Link RE450
RE355 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9558+QCA9880.

Specification:

720/600/200 MHz (CPU/DDR/AHB)
64/128 MB of RAM (DDR2)
8 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
1x 10/100/1000 Mbps Ethernet
7x LED, 3x button
UART header on PCB

Flash instruction:
Web:
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin
and use OEM System Tools - Firmware Upgrade site.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-13 09:21:20 +01:00
Jonas Gorski 8fdfba3d1a brcm63xx: switch to kernel 4.9
Now that we have support for it, let's switch to kernel 4.9.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-12 11:45:33 +01:00
Jonas Gorski cf90313ab2 ar7: switch to kernel 4.9
With generic run tested and ac49x compile tested, and no complaints so
far, let's switch to 4.9.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-12 11:45:33 +01:00
Jonas Gorski 09bc44454f ar7: fix ac49x compilation with 4.9
This will introduce a warning on 3.18, but fixes an error when
compiling for 4.9.

Fixes: cf9e0a59aa ("ar7: add kernel 4.9 support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-12 11:45:33 +01:00
John Crispin a464fba7eb Revert "mediatek: activate fpu feature flag"
This reverts commit 3594447a7d.

This causes the userland to not come up properly

Signed-off-by: John Crispin <john@phrozen.org>
2018-02-12 11:36:24 +01:00
Jonas Gorski e2ec3f7550 mvebu: fix sysupgrade from 17.04 for clearfog pro
When clearfog was renamed to clearfog pro, it broke sysupgrade from
17.04 as the new images now get rejected as incompatible. Fix this by
adding the legacy boardname to the compatible devices.

Fixes: ec4a8c6dee ("mvebu: ClearFog renamed upstream to ClearFog Pro")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-11 23:15:05 +01:00
Jonas Gorski 1ba38f6100 brcm63xx: add kernel 4.14 support
Add support for kernel 4.14. Increases compressed kernel size by ~64k
compared to 4.9.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-11 23:15:05 +01:00
Jonas Gorski b0c5e8b927 brcm63xx: add kernel 4.9 support
Add support for kernel 4.9 based on the more upstream comformant
partition defintions. Increases compressed kernel size by ~95k
compared to 4.4.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-11 23:15:05 +01:00
Jonas Gorski a27d59bb42 brcm63xx: switch to new partition layout specification
Now that we support parsing the expected upstream definition, update
the dts files to it.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-11 23:15:05 +01:00
Jonas Gorski 85f31afa88 brcm63xx: enhance dt partitions support to match upstream more closely
Partitions are supposed to be enclosed in an extra partitions node. Allow
the bcm63xxpart parser to cope with that.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-11 23:15:05 +01:00
Jonas Gorski a41ad1b6f6 brcm63xx: backport latest bcm63xx_enet changes from upstream
No functional changes, just simple cleanups.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-11 23:15:05 +01:00
Jonas Gorski 457e7a160a brcm63xx: fix ephy reset gpio lookup
The lookup needs to be called just "reset" for the common code.

Fixes: 054c0d4e31 ("brcm63xx: backport mdio-bus reset gpio support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-11 23:14:56 +01:00
Matthias Schiffer 355009ebe7
ar71xx: add missing config symbol ATH79_MACH_CF_E375AC
Fixes: bf66bb8c96 "ar71xx:add support for COMFAST CF-E375AC"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-02-11 18:41:25 +01:00
Hauke Mehrtens 3594447a7d mediatek: activate fpu feature flag
The arm CPUs uses in the supported Mediatket SoCs have a FPU accordingly
to the datasheet, activate it also. The CPU subtype "neon-vfpv4" is
selected, but the toolcahin generated for this SoC will still be
compiled with soft float and not with the hard float ABI as we haven't
the fpu feature flag set. If this toolchain is reused by other targets
this will even affect other targets.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-11 16:42:28 +01:00
Sven Eckelmann 25a72f5a01 ipq-wifi: drop OpenMesh A42 board-2.bin
The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.

[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-02-11 16:33:00 +01:00
Ding Tengfei bf66bb8c96 ar71xx:add support for COMFAST CF-E375AC
COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.

Short specification:

    2x 10/100/1000 Mbps Ethernet, with PoE support
    128MB of RAM (DDR2)
    16 MB of FLASH
    3T3R 2.4 GHz, 802.11b/g/n
    2T2R 5 GHz, 802.11ac/n/a, wave 2
    built-in 5x 3 dBi antennas
    output power (max): 500 mW (27 dBm)
    1x RGB LED, 1x button
    built-in watchdog chipset

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Ding Tengfei <dtf@comfast.cn>
2018-02-11 16:20:24 +01:00
David Bauer f17173f5a3 ar71xx: remove bs-partition ro-flag for UniFi AC
This removes the read-only flag from the bs (bootselect) partition
on UniFi AC devices. This allows to correct the indicator from which
partition the device is booting its kernel from.

See also:
 - https://github.com/freifunk-gluon/gluon/issues/1301
 - https://bugs.lede-project.org/index.php?do=details&task_id=662

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-02-11 16:16:03 +01:00
Henryk Heisig 14951e8f8e ramips: add support for TP-Link Archer C50 v3
TP-Link Archer C50 v3 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7612E.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power switch

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.

Flash instruction:

The only way to flash LEDE image in ArcherC50v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-11 16:04:16 +01:00
Henryk Heisig e39a240ba2 ramips: ArcherC20v4: use common TP-Link dtsi file
and remove common part from dts file.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-11 16:04:16 +01:00
Henryk Heisig 368a7f4cec ramips: change the TP-Link dtsi filename
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-11 16:04:16 +01:00
Pawel Dembicki 680e867d7f kernel: mtdsplit: Add support for D-link JBOOT
The D-Link devices with JBOOT bootloader use their own kernel
image header (stag + sch2 headers).

This driver find jImage header and set rootfs start after kernel file.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-02-11 16:02:52 +01:00
David Bauer 1113fcdc80 ipq806x: mark AVM FB4040 switchport as untagged
This commit marks the CPUs switchport explicit as untagged.
Otherwise, an eth0.1 interface is created and the devices
LAN-ports are not working.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-02-11 16:02:52 +01:00
Zoltan HERPAI 1ba6d59f2b x86: add preinit hook to reload microcode
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-02-11 14:39:24 +01:00
Zoltan HERPAI 72d949e7ba x86: enable microcode loading for Intel and AMD
Enable for 4.9 and 4.14.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-02-11 14:39:12 +01:00
Arne Zachlod 186aebf90a
ar71xx: Orders the names of the devices alphabetically.
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2018-02-11 00:08:25 +01:00
Adrià Llaudet 90ceb0aeb1 imx6: use DTS_DIR at image build code
Use "$(DTS_DIR)", defined at include/image.mk, instead of
"$(LINUX_DIR)/arch/$(LINUX_KARCH)/boot/dts" in order to generalize and
allow a better Device/* device-tree parameterization (i.e. DEVICE_DTS_DIR
and DTS_DIR).

Signed-off-by: Adrià Llaudet <adria.llaudet@gmail.com>
2018-02-10 21:02:53 +01:00
Evgeniy Didin 2fca8aa73e archs38: bump kernel to 4.14.
Update Linux kernel version from 4.9 to 4.14 for archs38.
config-4.14 was simply regenerated with "make kernel_menuconfig".

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
2018-02-10 20:59:52 +01:00
Evgeniy Didin b38758d4d4 kernel: backport fix undefined abort
While building mpi.ko module with stable Linux v4.14.14 an error occured:
>ERROR: "abort" [lib/mpi/mpi.ko] undefined!
In upstream Linux 4.15 this issue is fixed:
Commit 7c2c11b208be ("arch: define weak abort()")
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=7c2c11b208be09c156573fc0076b7b3646e05219

Commit dc8635b78cd8 ("kernel/exit.c: export abort() to modules")
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=dc8635b78cd8669c37e230058d18c33af7451ab1

So lets add backport patches until these fixes
are not applied in stable version.

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
CC: John Crispin <john@phrozen.org>
CC: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-10 20:58:39 +01:00
Hauke Mehrtens 3a2a54c055 kernel: rename CONFIG_TRACE_ENUM_MAP_FILE to CONFIG_TRACE_EVAL_MAP_FILE
This config option was renamed in upstream Linux commit 681bec0367
("tracing: Rename update the enum_map file")

Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-10 15:39:00 +01:00
Felix Fietkau 634673b215 ixp4xx: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-09 10:29:07 +01:00
Stijn Tintel 9a08c104e2 octeon: switch to kernel 4.14
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-02-08 19:04:38 +01:00
Stijn Tintel 3072908d0d kernel: bump 4.14 to 4.14.18
Refresh patches.

Remove upstreamed patches:
- apm821xx/010-crypto-gcm-add-GCM-IV-size-constant.patch
- backport/040-crypto-fix-typo-in-KPP-dependency-of-CRYPTO_ECDH.patch
Remove pending-4.14/650-pppoe_header_pad.patch, it is superseded by
upstream commit d32e5740001972c1bb193dd60af02721d047a17e.
Update patch that no longer applies: hack/204-module_strip.patch

Compile-tested: octeon, x86/64.
Runtime-tested: octeon, x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-02-08 18:43:13 +01:00
Daniel Golle 32f120b783 ramips: various fixes for zbt-we1226
Convert userspace code to use generic device-tree compatible board
detection method.  Users of the existing code will have to use
sysupgrade -F once to switch to the new generic board naming.
Properly setup pinctrl fixing the switch port LEDs.

Fixes commit 9c4fe103cb (ramips: add support for ZBT-WE1226)
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-02-06 03:00:33 +01:00
Daniel Danzberger 653af8ffd3 kernel: fix forwarding locally generated packages in bridge isolation patch
Locally generated packets weren't forwarded to the isolated interfaces in a
bridge. Isolation should only prevent the flooding of incomming packets to
other interfaces in the bridge.

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:16:26 +01:00
Felix Fietkau d3ea5fc9f3 ramips: use napi_alloc_frag and skb_free_frag
Slightly improves rx performance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:16:26 +01:00
Felix Fietkau 968b861612 ramips: improve NAPI polling to increase GRO batch size
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:16:26 +01:00
Felix Fietkau 798497c66e ar71xx: use global timestamp for hang check
Shrink the size of struct ag71xx_buf to 8 bytes, which improves cache
footprint

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:16:25 +01:00
Felix Fietkau 31e6016d2e ar71xx: only access device stats in tx handler if packets were processed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:16:25 +01:00
Felix Fietkau 890e7458b0 ar71xx: allocate rx/tx descriptor/buffers in one chunk
Reduces false sharing due to cache aliases

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:16:25 +01:00
Rosen Penev 4e03a742e0 ag71xx: Reorder ag71xx struct members for better cache performance
Qualcomm claims this improves the D-cache footprint. Origina commit message below:

From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Fri, 7 Jun 2013 10:57:28 -0500
Subject: [ag71xx] cluster/align structs for cache perf

Cluster the frequently used, per-packet structures in ag71xx near
to each other, and cacheline-align them.  Some other re-ordering
occurred to move "warmer" structures near the per-packet structures.

Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-02-05 10:16:25 +01:00
Felix Fietkau cde71a543c build: replace uses of OpenWrt with $(VERSION_DIST)
This makes the distribution name more configurable.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:15:53 +01:00
Matthias Schiffer 0c719bfcaf
ar71xx: /lib/ar71xx.sh: add model detection for TP-Link TL-WR810N
Properly report the revision in /tmp/sysinfo/model.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-02-03 14:13:26 +01:00
Jo-Philipp Wich fd30187c87 imagebuilder: fix reference to removed VERSION_SED variable
Fixes: ff8e9a4ecb ("treewide: combine VERSION_SED and VERSION_SED_SCRIPT")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-02-02 14:41:35 +01:00
Matthias Schiffer 3f7908d697
ar71xx-generic: enable ATH79_MACH_TL_WR841N_V8 machine
This machfile also contains the code for the TL-WR842N/ND v2, which is in
ar71xx-generic and not in ar71xx-tiny.

Fixes: 0cd5e85e7a "ar71xx: create new ar71xx/tiny subtarget for 4MB flash
devices"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-31 21:18:16 +01:00
Yousong Zhou 82ceb2ad2a build: add config option KERNEL_MIPS_FPU_EMULATOR
To make it more accessible for nodejs users to configure and run a build
on mips target lacking hardware fpu

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2018-01-29 15:06:53 +08:00
Catrinel Catrinescu 4ba2dd130a ar71xx: add ew-balin platform from Embedded Wireless
Add the Embedded Wireless "Balin" platform
 SoC: QCA AR9344 or AR9350
 RAM: DDR2-RAM 64MBytes
 Flash: SPI-NOR 16MBytes
 WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
 Ethernet: 3 x 10/100 Mb/s
 USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
 PCI-Express: 1 x lane PCIe 1.2
 UART: 1 x Normal, 1 x High-Speed
 JTAG: 1 x EJTAG
 GPIO: 10 x Input/Output multiplexed

The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade" image directly in vendor firmware.

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
2018-01-25 16:50:08 +01:00
Matthias Schiffer ad4232e3e9
ar71xx: add unaligned access hacks for VXLAN
Gives a ~5% performance gain.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-25 11:00:48 +01:00
Jackson Ming Hu 21d3643828 ramips: add support for Widora Neo 32MB flash revision
Widora has updated their Widora Neo board recently.

The new model uses 32MB WSON-8 factor SPI flash
instead of the original 16MB SOP-8 factor SPI flash.

All the other hardware components are the same as
the first revision.

Detailed hardware specs listed below:

CPU: MTK MT7688AN
RAM: 128MB DDR2
ROM: 32MB WSON-8 factor SPI Flash (Winbond)
WiFi: Built-in 802.11n 150Mbps?
Ethernet: 10/100Mbps x1
Audio codec: WM8960
Other IO: USB OTG;
	  USB Power+Serial (CP2104);
	  3x LEDs (Power, LAN, WiFi);
	  2x Keys (WPS, CPU Reset)
	  1x Audio In/Out
	  1x IPEX antenna port
	  1x Micro SD slot

Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-23 23:31:09 +01:00
Mathias Kresin a411881a40 ramips: add flash size postfix to Widora neo
Rename the Widora neo by adding a flash size prefix. Move the common parts
into a dtsi to be prepare everything for upcomming support of the 32MB
version.

Migrate the Widora neo to the generic board detection as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-23 23:31:09 +01:00
Hans Dedecker 6f425a28a4 kernel: generic: add 4.9 config option
When CGROUPS is enabled the new option CONFIG_CGROUP_NET_CLASSID is
selectable and not handled.
Add this option to the 4.9 kernel configuration.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-01-24 17:05:15 +01:00
Rosen Penev c25d9cbde8 ramips: Fix GB-PC1 cpuclock again
The intended frequency is 900 MHz, not 90.

Fixes: 7059ab48a6 ("ramips: fix cpuclock for the GB-PC1")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-01-24 07:33:42 +01:00
Daniel Golle 059b2f5481 ar71xx: fix MikroTik rb-nor-flash-16M-ac image
commit e15c63a375
ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)

changed the existing rb-nor-flash-16M-ac image in a way that it would
now only support the rb-wapg-5hact2hnd.
The board show however rather be added to the existing boards in the
rb-nor-flash-16M image template.

Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-01-24 01:24:39 +01:00
Daniel Golle 9c4fe103cb ramips: add support for ZBT-WE1226
MT7628NN (580MHz), 8MB SPI NOR, 64MB DDR2 RAM

Everything except for the switch LEDs works great.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-01-23 02:56:57 +01:00
Hauke Mehrtens b33c3e1b7c sunxi: Orange Pi R1: configure USB Ethernet controller.
Now the USB port is the WAN port.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-22 22:59:38 +01:00
Hauke Mehrtens 40db7a9dec sunxi: Orange Pi R1: Fix USB Ethernet and activate SPI
The USB Ethernet is not working with the patches proposed for upstream,
fix this and activate the SPI node as this board always has a SPI flash.

Both patches are also targeted for upstream kernel 4.16 and 4.17.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-22 22:59:38 +01:00
Hauke Mehrtens 75f7c1c9ac sunxi: use upstream patch for Orange Pi R1
Instead of using our own device tree definitions use the one provided in
the upstream kernel for 4.16.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-22 22:54:17 +01:00
Hauke Mehrtens b1c82cbd51 sunxi: backport stmmac network patches
Ethernet support was initial added in kernel 4.13, but deactivated
before the final release. This is backports the changes which are
activating it again from kernel 4.15.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-22 22:54:17 +01:00
Hauke Mehrtens ad2b3bf310 sunxi: Add support for kernel 4.14
This is based on the code for kernel 4.9, but a lot of 4.9 patches are
backports from more recent kernel version and can be removed now.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-22 22:51:02 +01:00
Hauke Mehrtens dda475ca30 sunxi: refresh kernel configuration
Just refresh the sunxi kernel configuration.
This also moves the CONFIG_CRYPTO_DEV_SUN4I_SS_PRNG option to the
config-4.9 file.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-22 22:49:59 +01:00
Gabor Juhos eb9e3651dd ar71xx: add support for the MikroTik RB911-2Hn/5Hn boards
The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:

  https://mikrotik.com/product/RB911-2Hn
  https://mikrotik.com/product/RB911-5Hn

The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.

Specifications:
  * SoC: Atheros AR9344 (600MHz)
  * RAM: 64MiB
  * Storage: 16 MiB SPI NOR flash
  * Ethernet: 1x100M (Passive PoE in)
  * Wireless: AR9344 built-in wireless MAC, single chain
              802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)

Notes:
  * Older versions of these boards might be equipped with a NAND
    flash chip instead of the SPI NOR device. Those boards are not
    supported (yet).
  * The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
    same hardware. Support for that can be added later with little
    effort probably.

Installation:

1. Setup a DHCP/BOOTP Server with the following parameters:
   * DHCP-Option 66 (TFTP server name): pointing to a local TFTP
     server within the same subnet of the DHCP range
   * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
     of the to be booted image. The usable intramfs files are:
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
       - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin

2. Press the reset button on the board and keep that pressed.

3. Connect the board to your local network via its ethernet port.

4. Release the button after the LEDs on the board are turned off.
   Now the board should load and start the initramfs image from
   the TFTP server.

5. Upload the sysupgrade image to the board with scp:
     $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin

5. Log in to the running system listening on 192.168.1.1 via ssh
   as root (without password):
     $ ssh root@192.168.1.1

7. Flash the uploaded firmware file from the ssh session via the
   sysupgrade command:
     root@OpenWrt:~# sysupgrade /tmp/fw.bin

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-22 10:53:45 +01:00
Gabor Juhos a4320b3332 ar71xx: make leds-gpio usable with single-ended GPIOs
Add patches for the leds-gpio driver to make it usable with
open-drain and open-source kind of GPIO lines.

This type of functionality is required by various MikroTik boards.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-22 10:53:32 +01:00
Gabor Juhos e379e60b17 ar71xx: mach-rbspi: return rb_info from rbspi_platform_setup
Modify the rbspi_platform_setup() function to return the pointer of the
rb_info structure. This allows board specific setup routines to access
the various fields of the information. It is useful for investigating
the hardware option bits for example.

Also update the board setup codes, to ensure that those handle the new
return value correctly.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-22 10:53:16 +01:00
Gabor Juhos c7371cd1ee ar71xx: add definitions for RouterBOARD hardware option bits
Add bit definitions for the 'hardware options' tag which is used in
the MikroTik devices' hardware configurations. These values can be
used in board setup codes, to do different initialization sequences.
The values were obtained from the RouterOS 6.41-rc38 patches.

Additionally, introduce two helper functions what make the processing
of the hardware options easy.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-22 10:53:00 +01:00
Hauke Mehrtens 36f1978a70 pistachio: make patches apply again
Support for Winbond NAND flash detection was added into the generic
patches and this conflicted with this patch adding Gigadevice support.

Fixes: 02050f7e7d ("kernel/4.{4, 9}: add manufacturer ID for Winbond NANDs")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-20 23:36:05 +01:00
Hauke Mehrtens 4d649ba949 ipq806x: make patches apply again
Some part of this patch was added to the generic patches as it was
needed also for some other target. Do not add it here any more.

Fixes: 02050f7e7d ("kernel/4.{4, 9}: add manufacturer ID for Winbond NANDs")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-20 23:24:02 +01:00
Hauke Mehrtens e390756eff x86: Add CONFIG_RETPOLINE to fix build
This adds support for the new configuration option CONFIG_RETPOLINE and
refreshes the configuration.

Fixes: d8565a06dc ("kernel: bump 4.9 to 4.9.77")
Fixes: 9ddfac8015 ("kernel: bump 4.14 to 4.14.14")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-20 22:46:34 +01:00
Hauke Mehrtens 4336efe14b kernel: use upstream patches for musl
This replaces the current patches used to make the kernel headers
compatible with musl with the version which was accepted upstream. This
is included in upstream kernel 4.15.
This was compile tested with iproute2 build on all supported kernel
versions with musl and one one with glibc.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-20 22:11:33 +01:00
Hauke Mehrtens f9aca01a53 kernel: backport fix for nftables on big Endian
nftables 0.8.1 generates some new commands which will not work without
this on big endian systems. This patch is included in Linux 4.11 and
later.

My rule matching a TCP port was not working:
nft add rule ip foo bar ct state new tcp dport 22 accept

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-20 20:22:01 +01:00
Kevin Darbyshire-Bryant a30370bbf1 kernel: bump 4.4 to 4.4.112
Refresh patches.
Remove upstreamed patches:

target/linux/generic/patches-4.4/030-2-smsc75xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch
target/linux/generic/patches-4.4/030-3-cx82310_eth-use-skb_cow_head-to-deal-with-cloned-skb.patch
target/linux/generic/patches-4.4/030-4-sr9700-use-skb_cow_head-to-deal-with-cloned-skbs.patch
target/linux/generic/patches-4.4/030-5-lan78xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch

CVEs completely or partially addressed:

CVE-2017-5715
CVE-2017-5753
CVE-2017-17741
CVE-2017-1000410

Compile-tested: ar71xx Archer C7 v2
Run-tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-01-20 20:22:01 +01:00
Kevin Darbyshire-Bryant d8565a06dc kernel: bump 4.9 to 4.9.77
Refresh patches.
Remove upstreamed patches:

target/linux/generic/backport-4.9/023-2-smsc75xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch
target/linux/generic/backport-4.9/023-3-cx82310_eth-use-skb_cow_head-to-deal-with-cloned-skb.patch
target/linux/generic/backport-4.9/023-4-sr9700-use-skb_cow_head-to-deal-with-cloned-skbs.patch
target/linux/generic/backport-4.9/023-5-lan78xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch

CVEs completely or partially addressed:

CVE-2017-5715
CVE-2017-5753
CVE-2017-17741
CVE-2017-1000410

Compile-tested: ar71xx Archer C7 v2
Run-tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-20 20:22:01 +01:00
Kevin Darbyshire-Bryant 9ddfac8015 kernel: bump 4.14 to 4.14.14
Refresh patches.

CVEs completely or partially addressed:

CVE-2017-5715
CVE-2017-5753
CVE-2017-17741
CVE-2017-1000410

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-20 20:22:00 +01:00
Gabor Juhos 02050f7e7d kernel/4.{4, 9}: add manufacturer ID for Winbond NANDs
Some MikroTik devices are using a Winbond NAND flash. Linux treats
it as an unknown NAND before version 4.11:

  nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1
  nand: Unknown NAND 128MiB 3,3V 8-bit
  nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64

Backport a patch from 4.11 to show the manufacturer correctly:

  nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1
  nand: Winbond NAND 128MiB 3,3V 8-bit
  nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64

Tested on a MikroTik R951Ui-2HnD board.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-20 20:22:00 +01:00
Christian Lamparter 9c2ac19b03 ipq806x: remove merged ipq4019 patch
The patch 0022-dts-ipq4019-support-ARMv7-PMU.patch
was merged into 4.8-rc1.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-18 21:21:11 +01:00
Christian Lamparter 5988364cf3 ipq806x: remove dependency on non-existent kmod
During the integration of the ipq40xx target,
the phy drivers were included into the ipq806x's
target kernel config.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-18 21:21:11 +01:00
Christian Lamparter 51dd8f3875 ipq-wifi: align AVM FRITZ!Box 4040's board-2.bin package
This patch renames the AVM FRITZ!Box 4040's board-2.bin
file and package to match the 'vendor_product' format.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-18 21:21:11 +01:00
Christian Lamparter 42b47f1b40 ipq806x: overhaul AVM FRITZ!box 4040 device-tree file
This patch aligns the device-tree file with the latest
guidelines.
 - No longer include qcom-ipq4019-ap.dk01.1.dtsi. This
   file is only partially upstream and therefore subjected
   to changes that might not be compatible with the board.

   As a result, the definitions from the file have been
   copied into this dts.

 - exclusively use decimal GPIO addresses.

 - reorganize the reserved-memory layout to waste less
   memory. There's no point in keeping the u-boot loader
   around. This should also make it possible    to create
   an image that will boot with the original EVA/ADAM2 loader
   without needing to install the modified u-boot loader.
   And finally mark the "tz-apps" as reusable.
   There isn't a way to  upload apps to the trust-zone in OpenWrt
   yet. But it might see some use in the future as a "secure"
   key-store/TPM.

 - sort the first-level nodes alphabetically.
 - sort nodes with an address by the address.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-18 21:21:11 +01:00
Serg Studzinskii eb58b14d27 ramips: tl-wr840n-v5: increase firmware partition for 4Mmtk layot
According to console log during TP-Link TL-WR840N v5 OEM firmware update
procedure 0x3e0000-0x3f0000 64kB "config" partition, which is used to store
router's configuration settings, is erased and recreated again during every
OEM firmware update procedure, thus does not contain any valuable factory data.
So it is conviniant to use this extra 64kB erase block for jffs overlay due
limited flash size on this device like it used on TP-Link's ar71xx boards.

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
2018-01-18 08:04:18 +01:00
尤晓杰 a7e62b4be1 kirkwood: fix sysupgrade
The platform_check_image() stub need to return 0 for success, otherwise
the sysupgrade will fail with:

  Image check 'platform_check_image' failed.

Fixes: aa6f5f1787 ("kirkwood: use image metadata")
Signed-off-by: 尤晓杰 <yxj790222@163.com>
[reworded commit message}
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-18 07:26:28 +01:00
Mathias Kresin b6868e2f47 ipq806x: fix ZyXEL NBG6817 sysupgrade
Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.

It allows to change the boardname without adding another compatibility
layer to the zyxel sysupgrade.

Fixes: 33f09cf151 ("ipq806x: convert to dt-based board-detection")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-18 07:22:37 +01:00
Gabor Juhos ec4e9a88ff ar71xx: drop mdio-gpio.h include from mach-om5pacv2.c
The setup code of the OpenMesh OM5P ACv2 device uses nothing
from the mdio-gpio.h header, so remove the inclusion of that.

Also remove the kernel version check which is needed only
because the mdio-gpio.h header exists in a different path
in older kernels.

Compile tested only.

Cc: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Koen Vandeputte d3afd2a400 cns3xxx: switch to kernel 4.14
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte 9e7d53c3fe cns3xxx: refresh patches
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte 7f93624d5f cns3xxx: remove deprecated uart flags
Flag UPF_NO_TXEN_TEST is deprecated.

Remove it.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte f3dec44520 cns3xxx: fix ethernet IRQ imbalance in 4.14
Kernel 4.14 contains more warnings regarding NAPI usage, which showed
following warning:

[ 4016.420000] ------------[ cut here ]------------
[ 4016.430000] WARNING: CPU: 1 PID: 14 at kernel/irq/manage.c:525
__enable_irq+0x3c/0x78
[ 4016.440000] Unbalanced enable for IRQ 51
[ 4016.440000] Modules linked in: ath9k ath9k_common pppoe ppp_async
ath9k_hw ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat
ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat
xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS
xt_REDIRECT xt_LOG slhc nf_reject_ipv4 nf_nat_redirs
[ 4016.500000] CPU: 1 PID: 14 Comm: ksoftirqd/1 Tainted: G        W
       4.14.11 #0
[ 4016.500000] Hardware name: Gateworks Corporation Laguna Platform
[ 4016.510000] Backtrace:
[ 4016.510000] [<c010a28c>] (dump_backtrace) from [<c010a56c>]
(show_stack+0x18/0x1c)
[ 4016.520000]  r7:c059df4b r6:00000000 r5:60000093 r4:00000000
[ 4016.530000] [<c010a554>] (show_stack) from [<c048b04c>]
(dump_stack+0x94/0xb4)
[ 4016.530000] [<c048afb8>] (dump_stack) from [<c011760c>]
(__warn+0xc8/0xf8)
[ 4016.540000]  r7:c059df4b r6:c015144c r5:00000000 r4:cf863e08
[ 4016.550000] [<c0117544>] (__warn) from [<c011767c>]
(warn_slowpath_fmt+0x40/0x48)
[ 4016.550000]  r9:cf863eb0 r8:00000036 r7:00000000 r6:c0636360
r5:00000033 r4:cf80a500
[ 4016.560000] [<c0117640>] (warn_slowpath_fmt) from [<c015144c>]
(__enable_irq+0x3c/0x78)
[ 4016.570000]  r3:00000033 r2:c059e0c5
[ 4016.570000] [<c0151410>] (__enable_irq) from [<c01514ec>]
(enable_irq+0x64/0x7c)
[ 4016.580000] [<c0151488>] (enable_irq) from [<c0335c14>]
(eth_poll+0x28c/0x558)
[ 4016.590000]  r5:d08926c0 r4:cf894488
[ 4016.590000] [<c0335988>] (eth_poll) from [<c03b1718>]
(net_rx_action+0xfc/0x2e8)
[ 4016.600000]  r10:cf863eb8 r9:cf863eb0 r8:00000001 r7:0f7b5000
r6:c0636360 r5:cfdeb360
[ 4016.610000]  r4:cf894488
[ 4016.610000] [<c03b161c>] (net_rx_action) from [<c0101510>]
(__do_softirq+0xe0/0x228)
[ 4016.620000]  r10:00000100 r9:c070204c r8:c0702040 r7:00000003
r6:00000008 r5:40000003
[ 4016.620000]  r4:cf862000
[ 4016.630000] [<c0101430>] (__do_softirq) from [<c011ae28>]
(run_ksoftirqd+0x34/0x58)
[ 4016.630000]  r10:c0133964 r9:00000000 r8:00000001 r7:00000000
r6:c070b44c r5:cf862000
[ 4016.640000]  r4:cf8037e0
[ 4016.640000] [<c011adf4>] (run_ksoftirqd) from [<c0133adc>]
(smpboot_thread_fn+0x178/0x190)
[ 4016.650000] [<c0133964>] (smpboot_thread_fn) from [<c013099c>]
(kthread+0x11c/0x138)
[ 4016.660000]  r9:cf8037e0 r8:cf802cdc r7:cf839df8 r6:cf803800
r5:00000000 r4:cf802cc0
[ 4016.670000] [<c0130880>] (kthread) from [<c0107218>]
(ret_from_fork+0x14/0x3c)
[ 4016.680000]  r10:00000000 r9:00000000 r8:00000000 r7:00000000
r6:00000000 r5:c0130880
[ 4016.680000]  r4:cf803800 r3:cf862000
[ 4016.690000] ---[ end trace 51114df08f429115 ]---

This is triggered by calling eth_schedule_poll(sw) after the IRQ has
been re-enabled.

Rework the network code to only enable IRQ's again if NAPI agrees it's
safe to do so.

Also only re-enable IRQ *after* cleaning up the RX ring and re-enabling
DMA, which otherwise resulted in ugly warnings regarding dirty page
fragments.
These popped up nearly immediately when building the kernel with O2 iso
Os.

--> Note that this change fixes stability issues, at the cost of ~8%
throughput performance.

While at it, also change the iface name being used in warning prints,
making it more obvious: "switch%d" --> "cns3xxx_eth"

The changes have been tested on 4 boards, each moving ~30TB of data

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte 9f54aaff70 cns3xxx: update patches for 4.14
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte 2543e7f08c cns3xxx: refresh kernel 4.14 config
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte 0ef702c7e3 cns3xxx: copy patches for kernel 4.14
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte 809a265e35 cns3xxx: copy config for kernel 4.14
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Gabor Juhos fbd33c2b6c ar71xx: fix format of the 701-MIPS-ath79-add-routerboard-detection patches
Commit e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAP
G-5HacT2HnD (wAP AC") broke the format of the patches. In unified diff
format, the unchanged, contextual lines must be preceded by a space
character.

Refresh the patches with quilt to fix them.

Fixes: e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAPG-5HacT2HnD (wAP AC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Gabor Juhos 508999d366 ar71xx: fix format of the 741-MIPS-ath79-add-PCI-for-QCA9556-SoC patches
The patches introduced in commit 20e68f6d39 ("ar71xx: kernel: enable
PCI on QCA9556 SoC") have non standard format. In unified diff format,
the unchanged, contextual lines must be preceded by a space character.

Refresh the patches with quilt to fix them.

Fixes: 20e68f6d39 ("ar71xx: kernel: enable PCI on QCA9556 SoC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Gabor Juhos bc178f6b15 ar71xx: mach-rbspi: simplify reset button registration
The setup code defines four individual structures for the
Reset buttons of the supported boards. The only difference
between the definitions is the GPIO number used for the
button.

Replace the different structures with one generic variant,
and add a helper function to simplify the button registration.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Koen Vandeputte 8954bc31ed imx6: add support for the intel gbit driver on GW5520
The Gateworks GW5520 board uses 2x intel gigabit mac's, instead of the
internal i.MX6 FEC.

Add support for these.

Signed-off-by: Scott V. Kamp <outbackdingo@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Pavel Kubelun 644a0d5403 ipq8065: adjust SS USB PHY power settings
According to QSDK ipq8065 has different SS USB PHY power settings.

Adjust it according to QSDK settings.

It also corresponds to oem Netgear R7800 tarball for soc ver >= 2.
eeac2e1019/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c (L2494)

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:05:11 +01:00
Pavel Kubelun e93a16ed3f ipq806x: usb: add phy 1 master reset control
In current state only phy 0 master reset is controlled.
Add the phy 1 reset.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:04:57 +01:00
Pavel Kubelun de748a121e ipq806x: usb: Control USB master reset
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=eggplant&id=a86bda9f8a7965f0cedd347a9c04800eb9f41ea3

Commit message:
"During removal of the glue layer(dwc3-of-simple), USB master reset is set to active and during insertion it is de-activated."

Change-Id: I537dc810f6cb2a46664ee674840145066432b957
Signed-off-by: Vasudevan Murugesan <vmuruges@codeaurora.org>
(cherry picked from commit 4611e13580a216812f85f0801b95442d02eeb836)"

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:06 +01:00
Pavel Kubelun 6617f3c6ab ipq806x: dwc3: Fix power_on and power_off sequence
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=d316437c9cdb70023a760342678f32e27241725a

The commit fixes:
- dwc3 phy module unloading
- possibly fixes FS#177 when some devices were improperly enumerated as HS while being SS thus stucking the driver during boot.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:06 +01:00
Pavel Kubelun c263e18a53 ipq806x: Update HSIO recommended usb phy settings
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=cf82fdf4bdd081cd81bb081f7815b915bc8bb851

The comit adjusts USB dwc3 phy default values as per QSDK recomendation and allows to set it through DT.

Commit message:
"SoC version based values will be recovered from the device node.
If device node does not have such values, defaults are applied.

Change-Id: Ia77b5b7fe95ce1a433885df1761091bced98d989
Signed-off-by: Gokul Sriram Palanisamy <gpalan@codeaurora.org>"

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:06 +01:00
Pavel Kubelun a4c1767897 Revert "ipq8064: Fix dwc3 module unloading"
Preparing for proper fixes thus reverting commits:
- 8db079a9ff "ipq8064: Fix dwc3 module unloading"
- c75f059b0c "ipq8064: Fix dwc3 module unloading"

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:05 +01:00
Pavel Kubelun 7903a9219c ipq806x: update clk and cpufreq drivers
A newer clk and cpufreq drivers for ipq806x platform had been sent upstream.

A change that i have noticed is that now it's possible to set min, cur and max frequencies from sysfs (previously it was bugged and caused nothing).

Following patches are removed:
 - 0036-clk-Avoid-sending-high-rates-to-downstream-clocks-du.patch - seems it was dropped from the patchset by current committer.
 - 0044-clk-qcom-krait-Remove-CLK_IS_ROOT.patch - already applied to the driver itself in the corresponding patch.
 - 0057-clk-qcom-Add-regmap-mux-div-clocks-support.patch - seem to be irrelevant to ipq806x.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:05 +01:00
Pavel Kubelun 83499bef73 ipq806x: force 2nd pci slot into gen1 mode
According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode.
EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode.

In previous commit we've added the support for this option, so enable it in DT for affected devices.

QSDK ref:
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=f3b07fe309027c52fc163149500cedddd707c506

While at it move the phy transmit termination offset value into dtsi file as it's platform specific.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:05 +01:00
Pavel Kubelun 36a96a4493 ipq806x: fix wireless regression
In current state there's huge regression on ipq806x target that causes the device to transmit broken/malformed frames that are not corrected/detected by error control mechanisms and other less severe issues.
https://bugs.lede-project.org/index.php?do=details&task_id=1197

This finally had been narrowed down to patch 0071-pcie-qcom-fixes.patch

Meanwhile QSDK contains a handful of commits that add support for ipq806x to upstream qcom pcie driver
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/log/drivers/pci/host/pcie-qcom.c?h=eggplant
Unfortunately qca developers do not bother to push it upstream.

Using those commits instead of lede 0071 patch fixes mentioned issue and probably many others as it seems that corrupted data has been originating within pcie misconfiguration.

Fixes: FS#1197 and probably others
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:05 +01:00
Daniel Gimpelevich e4442ca2d8 ramips: use blue status LED for Xiaomi Router 3G
The blue LED is what other firmwares use for this device, and it's a lot
easier on the eyes than its shade of yellow, which implies an error
condition.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[merge into existing $boardname:blue:status block]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: Cezary Jackiewicz <cezary@eko.one.pl>
2018-01-15 21:45:43 +01:00
Maxim Anisimov 5bdd238b63 ramips: add support for TP-Link Archer C20 v4
TP-Link Archer C20 v4 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
  work.

Flash instruction:

The only way to flash LEDE image in ArcherC20v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-01-15 21:45:43 +01:00
Maxim Anisimov ff1e895530 ramips: rename TP-Link Archer C20 to TP-Link Archer C20 v1
This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1"
because of TPLINK released new TP-Link Archer C20 v4. Additionally
migration to the generic board detection has been made.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-01-15 21:45:43 +01:00
David Bauer 6c56e968c1 ar71xx: fix TP-Link Archer C7 v4 switch LEDs
Match mapping of the switch LEDs according to the TP-Link
firmware behavior. LAN port 1 triggers the most right LAN LED,
LAN port 2 the second LAN LED from the right and so on.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-01-15 21:45:43 +01:00
Chen Minqiang a8054d83dc ramips: add image checks
As long as we can't enforce image metadata, we need to use (platform)
image checks to have at least soem kind of validation.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-01-15 21:45:43 +01:00
Mathias Kresin 16f2befc3c ipq806x: drop ubifs support
Ubifs is disabled for all boards except the evaluation boards and the
Fritz!Box 4040 anyway. According the author, the ubifs support for the
Fritz!Box 4040 wasn't enabled on purpose.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Mathias Kresin 0af5e9bdc4 ipq806x: drop legacy image leftovers
Remove leftover code used for legacy images. There are no relevant
binary differences for the images after removing the legacy leftovers.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Mathias Kresin 52e7df3f49 ipq806x: unset filesystem specific build command by default
Initialise the filesystem specific build command. Otherwise it will be
unintended inherit to following images and will cause a wrong image
format.

The issue is around for ages but was only recently triggered due to the
added support for the Openmesh a42.

Fixes: FS#1276

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Mathias Kresin f319c5c254 ipq806x: remove unnecessary filesystem specific build
The Openmesh factory image doesn't need a squashfs specific build command.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Mathias Kresin f2a8e02134 ipq806x: use bin file extension for sysupgrade-tar images
Use the file extension bin for sysupgrade-tar images to unify the file
extension across the target/tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Piotr Dymacz 030176e0e7 ar71xx: image: rework EnGenius ENS202EXT factory image
Current EnGenius ENS202EXT factory image recipe version causes factory
images of the following devices to be corrupted. This issue wasn't
visible until recent changes of image Makefile snippets order.

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 13:39:54 +01:00
Jo-Philipp Wich 497f028da1 omap24xx: remove referece to not existing kmod-usb-musb-tusb6010
Remove leftover reference to a not existing kmod-usb-musb-tusb6010 from
the omap24xx target, the corresponding module is built into the kernel.

Fixes: 96815fe0a2 ("kernel: remove omap24xx specific kernel module packages")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-15 13:13:34 +01:00
Roger Pueyo Centelles e15c63a375 ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)
This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.

See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9556
 - RAM: 64 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
   · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
 - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive
   PoE in

Working:
 - Board/system detection
 - Sysupgrade
 - Serial console
 - Ethernet
 - 2.4 GHz radio
 - 5 GHz radio
 - Reset button

Not working:
 - LEDs (added according to Mikrotik's GPL sources but not functional)

 Unsupported:
 - ZT2046Q SPI temperature and voltage sensor

Contributors: Giuseppe Tipaldi (@Ciusss89)
              Ricky (@rickydee)

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
2018-01-15 04:14:18 +01:00
Roger Pueyo Centelles 20e68f6d39 ar71xx: kernel: enable PCI on QCA9556 SoC
This patch enables the PCI bus on the QCA9556 SoC, the same way it is
done on the same family SoC QCA9558.

Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-01-15 04:14:18 +01:00
Piotr Dymacz 5352669c2c ramips: add support for ALFA Network AC1200RM
ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and
USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN.

Specification:

- MT7620A (580 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4
- 2T2R 2.4 GHz (MT7620A)
- 2T2R 5 GHz (MT7612EN)
- 1x USB 2.0
- 9x LED (8 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12-24 V)
- 2x UART, I2C, I2S and LED headers

Flash instruction (do it under U-Boot, using UART and TFTP server):

Select option "2: Load system code then write to Flash via TFTP" and
use "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz 2e5252d346 ar71xx: add support for GL.iNet GL-AR750
GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on
Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 1x USB 2.0 (power controlled by GPIO)
- 1x microSD (GL857L)
- 3x LED (all driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- header for optional PoE module
- 1x micro USB for main power input
- UART + I2C header on PCB

Flash instruction:

Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used
to flash OpenWrt/LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz 6cf682e214 ar71xx: image: move Sitecom WLR-8100 from legacy to generic
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Davide Fioravanti a85db951db ar71xx: fix Sitecom WLR-8100 support
This patch fixes Sitecom WLR-8100:

- mtd layout
- LAN and WAN MAC address setup
- 2.4 GHz Wi-Fi MAC address setup
- 5 GHz Wi-Fi support (calibration data, MAC address setup, missing
  ath10k-* packages)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[squashed commits, fixed whitespace issues, reworded commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz af8f0629df ar71xx: add support for ALFA Network R36A
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.

Specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz 1f06144cde ar71xx: add support for Teltonika RUT900
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.

There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.

This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector

Serial console pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:09:43 +01:00
Piotr Dymacz 4b0eebe9df ar71xx: add support for ALFA Network N5Q
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 21:30:16 +01:00
Piotr Dymacz 7f9f42d42e ar71xx: add support for ALFA Network AP91-5G
ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB

Flash instruction:

Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Piotr Dymacz ce6c7691ec ar71xx: base-files: cosmetic cleanups in preinit scripts
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Piotr Dymacz 9a867fcddf ar71xx: base-files: drop LED control from 05_set_iface_mac_ar71xx
There is no "dir-615-c1:green:wancpu" LED defined in mach-dir-615-c1.c

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Piotr Dymacz 71489bfa48 ar71xx: base-files: fix boards order in 05_set_preinit_iface_ar71xx
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Stijn Tintel d6679090b4 kernel: add missing config symbol
The KEXEC_FILE symbol exists for X86 since kernel 3.17, and since 4.10
for PPC64. Add it to x86/config-4.9 and to generic/config-4.14.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-01-14 21:27:33 +02:00
Stijn Tintel 0c12830d4a kernel: add missing DRM symbols to generic config
Several new DRM symbols that were introduced after 4.9 are missing in
the generic config for 4.14, so add them.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-01-14 21:27:26 +02:00
Stijn Tintel 6577244b6f kernel: sort generic configs
Use kconfig.pl to sort the generic kernel configs.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-01-14 20:31:02 +02:00
Stijn Tintel 34e319dd30 kernel: move DRM_DEBUG_* symbols to generic config
While working on a new target (meson), the kernel build failed due to
missing DRM_DEBUG_MM_SELFTEST symbol. This can potentially happen on all
targets that enable DRM drivers in the kernel config or via kmod
packages, so add it to the generic config and remove it from x86
subtarget configs, together with DRM_DEBUG_MM.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-01-14 20:15:01 +02:00
Matthias Schiffer 0cd5e85e7a
ar71xx: create new ar71xx/tiny subtarget for 4MB flash devices
This new subtarget sets the small_flash flag and removes unused kernel
configuration.

small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default
configuration; removing unneeded hardware support from ar71xx/tiny saves
another ~18KB (both after LZMA).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-13 19:54:45 +01:00
Matthias Schiffer 29d126b5c1
ar71xx/generic: add generic- prefix to vendor-specific image Makefile snippets
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-13 19:54:45 +01:00
Matthias Schiffer 3d365831b0
ar71xx: reorganize kernel configuration
Rather than including all machines for the generic subtarget in the base
configuration, leave the base configuration without specific machines and
create a proper subtarget config for ar71xx/generic. The configuration
diffs of the mikrotik and nand subtargets get significantly shorter, as
will the configurations of future subtargets.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-13 19:54:45 +01:00
Matthias Schiffer d04056e5ea
ar71xx: disable devicetree support
While we'd like to convert ar71xx to DT-based configuration
eventually, we aren't quite there yet, and shipping half-baked DT support
that is not used at all wastes precious space.

Saves ~120KB before LZMA, ~33KB after LZMA.

Run-tested on TP-Link CPE510 and TL-WR841 v7.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-13 19:54:45 +01:00
Jo-Philipp Wich 7e99a6ba69 target: disable CONFIG_PROC_PAGE_MONITOR on most targets
Disable CONFIG_PROC_PAGE_MONITOR in most places and only keep it enabled
for virtual targets such as malta or potent ones like x86.

This saves up to 4KB of uncompressed kernel size and significantly
decreases CPU load under certain workloads.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-13 15:04:15 +01:00
Sven Eckelmann 86e18f6706 ipq806x: add support for OpenMesh A42
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
  - 802.3af POE on Ethernet 1
  - 18-24v passive POE (mode B) on Ethernet 2

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-01-13 08:00:14 +01:00
Sven Eckelmann c242643d1a ipq806x: enable gpio watchdog support
The kernel driver gpio-wdt or the userspace tool om-watchdog can be used to
trigger external gpio watchdog chips. The gpio-wdt driver has the benefit
that it can be configured together with the rest of the device in the DTS
and better integrates in the OpenWrt via procd.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-01-13 08:00:07 +01:00
Luis Araneda 7293499f71 ipq806x: Sort occurrences of boardame alphabetically
This restores the alphabetical sort that was present
before the renaming of boardname.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:03 +01:00
Luis Araneda 33f09cf151 ipq806x: convert to dt-based board-detection
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree

Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script

Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:03 +01:00
Luis Araneda 3cbdae2421 ipq806x: sync image filename with dt compatible string
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:02 +01:00
Luis Araneda 09e13bd341 ipq806x: add a helper variable with the vendor name stripped
This will allow to maintain the current syntax for LEDs config
when switching to a device tree compatible string boardname.

None of the current boards use a comma in the boardname, so they
will be unaffected.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:02 +01:00
Luis Araneda 8ed5dfedc6 ipq806x: add missing dt compatible string to ap-dk04 board
Compatible string is mandatory to dts files

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:02 +01:00
Mathias Kresin c3d9fe96dc ipq806x: drop partitial supported boards
There are only artifacts for these boards in our tree and not even
partial support.

Drop teh stale files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-13 07:33:02 +01:00
Florian Fainelli 0cf7c54023 armvirt: Resync kernel configuration
The 4.14 kernel configuration defaulted to a v4/v5 multiplatform while
4.9 was using a v6/v7 default configuration. Resync 4.14 against 4.9 so
they are nearly identical.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-01-12 15:14:27 -08:00
Florian Fainelli d8a12a7d9f kernel: Add a bunch of missing symbols
Add a bunch of missing configuration symbols found while building
armvirt for 4.14 after re-synchronization of the configuration between
4.9 and 4.14.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2018-01-12 15:14:27 -08:00
Rafał Miłecki 3618dcbff8 bcm53xx: rename SPI driver fix to use 0xx prefix as it was accepted
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-01-12 23:29:48 +01:00
Rafał Miłecki 8cd3370cce bcm53xx: use upstream fix for PCI iproc driver regression
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-01-12 23:27:43 +01:00
Rosen Penev 7059ab48a6 ramips: fix cpuclock for the GB-PC1
The GnuBee PC1 stock bootloader runs at 900Mhz. This fixes bad clock drift when running the platform.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-01-12 08:02:51 +01:00
Christian Lamparter 3c94691620 apm821xx: remove kernel 4.9 support
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-12 08:00:05 +01:00
Christian Lamparter e97f92bbf9 apm821xx: switch to 4.14.x kernel
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-12 08:00:05 +01:00
Christian Lamparter 780477d17c apm821xx: backport crypto4xx patches from 4.15
This patch backports changes to crypto4xx in order
to get the crypto4xx operational.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-12 08:00:04 +01:00
Christian Lamparter e4371779d2 apm821xx: convert MR24 to use DT PHY defintion
Convert the MR24 to use the DT phy probing and at803x PHY driver.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-12 08:00:04 +01:00
Christian Lamparter 15faf389ad apm821xx: add linux 4.14 apm821xx patches
This patch updates the apm821xx target to use the 4.14 kernel.

4.14 finally ships with a driver for the WNDR4700's tc654 fan
controller. The custom driver is deprecated in favor of the
upstream driver and the thermal cooling definitions in the DTS
are updated.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-01-12 08:00:04 +01:00
Hauke Mehrtens 31fca075c7 at91: create device specific sdcard images
Without this patch one sdcard image with the following name is created
for all devices:
openwrt-at91-sama5--sdcard.img.gz
This makes the build system create device specific versions like:
openwrt-at91-sama5-at91-sama5d2_xplained-sdcard.img.gz

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-01-11 20:35:33 +01:00
Kevin Darbyshire-Bryant 7c7586b6d0 kernel: bump 4.14 to 4.14.13
Refresh patches

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-01-11 20:34:33 +01:00
Kevin Darbyshire-Bryant eceff9ea8f kernel: bump 4.4 to 4.4.111
Refresh patches

Tested-on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-01-11 20:33:40 +01:00
Kevin Darbyshire-Bryant 2228dbf4e6 kernel: bump 4.9 to 4.9.76
Refresh patches

Tested-on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-11 20:32:36 +01:00
Jo-Philipp Wich 17b194aeac sdk: change base feed fallback to git.openwrt.org
Change the hardcoded lede-project.org base feed fallback to
$(PROJECT_GIT)/openwrt/openwrt.git instead.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-11 18:20:07 +01:00
Rafał Miłecki 05cb6aa69f bcm53xx: replace linux,part-probe with a proper partitions subnode
This solution is more upstream compatible as it only requires specifying
of_match_table in the parser code and doesn't depend on linux,part-probe
which is solution made generic by a LEDE downstream patch that can't be
upstreamed.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-01-11 14:05:10 +01:00
Rafał Miłecki bde5e7a632 kernel: backport mtd implementation for "compatible" in "partitions" subnode
This backports upstream support for "compatible" DT property set for the
"partitions" subnode of flash node. It allows specifying how partitions
should be created/parsed. Right now only "fixed-partitions" is
supported.

It should eventually replace our downstream "linux,part-probe" solution.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-01-11 12:07:49 +01:00
Matthias Schiffer ef27f15330
kernel: allow disabling multicast routing support
Multicast routing support is not needed in most setups, and increases the
size of the kernel considerably (>10K after LZMA). Add a config switch to
allow disabling it.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-11 11:51:24 +01:00
Matthias Schiffer 1abb5c6db1
generic: unlock Winbond flash on boot
The underlying issue breaking Spansion flash has been fixed with "mtd: spi-nor:
wait until lock/unlock operations are ready" and "mtd: spi-nor: wait for SR_WIP
to clear on initial unlock", so we can support unlocking for Winbond flash
again.

This is necessary to have writable flash on certain UBNT devices with some
bootloader versions.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-11 11:51:07 +01:00
Jo-Philipp Wich f66fe0080a sunxi: enable missing config symbol
Enable CONFIG_MFD_AXP20X_I2C after the switch to Kernel 4.9, this symbol
is reportedly required to get USB working on the Banana Pi.

Ref: https://forum.lede-project.org/t/sunxi-kernel-4-9-usb-not-working/10513
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-11 03:14:07 +01:00
Mathias Kresin d3fd38637f lantiq: create ATM/PTM interfaces with dsl as netdev name
Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the
original netdev might disappear before br2684ctl has finished appling it's
setting:

 local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully
 local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC
 kern.info kernel: dsl0: renamed from nas0
 kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device
 local2.err br2684ctl[1667]: Could not configure interface:No such device or address

By passing the final used netdev name to br2684ctl_wrap another race
condition workaround will be enabled again.

Change the lantiq ptm driver to create a netdev with the name dsl as well.
Albeit the rename via 'ip link' works fine so far, using a different
approach for ptm then atm could be confusing.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-10 08:08:53 +01:00
Jo-Philipp Wich 57157618d4 armvirt: re-enable VFP support
Enable CONFIG_VFP again which was disabled during the 4.9 -> 4.14 bump.

Boot tested both 32 and 64 bit subtargets using initramfs images with the
qemu-system-arm and qemu-system-aarch64 emulators.

Fixes: aa100b66f2 ("armvirt: bump to v4.14")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-10 00:44:08 +01:00
Jo-Philipp Wich 7226c7850b armvirt: 64: add missing kernel config symbols
Fixes: aa100b66f2 ("armvirt: bump to v4.14")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-10 00:44:08 +01:00
Kevin Darbyshire-Bryant efb375b579 kernel: bump 4.4 to 4.4.110
Refresh patches

Fixes:  CVE-2017-5754 aka Meltdown

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
[fix typo in commit msg, conflict after 4.14 bump]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-01-10 00:11:39 +02:00
Kevin Darbyshire-Bryant 1d2590f838 kernel: bump 4.9 to 4.9.75
Refresh patches

Fixes:  CVE-2017-5754 aka Meltdown

Tested-on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[fix conflict after 4.14 bump]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-01-10 00:11:39 +02:00
Mathias Kresin 0674a99f7e kirkwood: sort occurrences of boardame alphabetically
This restores the alphabetical sort that was present
before the renaming of boardname.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Alberto Bursi c19f811c4d kirkwood: add pogoplug v4
also known as
POGO-V4-A3-02
or
POGO-V4-A3-01

SoC: Marvell 88F6192 800Mhz
SDRAM memory: 128MB
Gigabit ethernet: 1 Marvell 88E1310
Flash memory: 128MB
2 status LEDs (one green one red)
1 "Eject" button on the back (used as "Reset" button)
1 USB 2.0 port (on upper side)
1 sata slot (power + data) for 2.5'' drives (upper side)
2 USB 3.0 ports from a controller on PCIe x1 of the SoC
1 full-size SDcard slot (fits a whole SD card into it)

This device supports the (linux-only) kwboot tool to send
a new uboot over serial console, so it is easy to unbrick
in case the uboot is erased and the device won't boot.

-----
Install instructions:
-----
Since it's not possible to get ssh access to these
devices, the only way to take control is to
solder pins to get TTL serial access.

Case can be opened by removing screws beneath two rubber
feet at back of device, then lifting while prying the
sides of the upper part out to unhook a latch on each
side about 2/3rds of the way toward the front.

Serial connection pins are those labeled "J11", left
of SD as you face SD opening.
Pins are (from left to right, i.e. the first in the list
is the nearest to the SD slot) GND, Rx, Tx.
Do not connect +V pin if you use a USB (self-powered)
TTL-to-USB dongle. Any USB TTL-to-USB converter will work.
Baud rate is 115200, parity "none", databits "8",
flow control "none".

Stock uboot is unable to read ubi partitions (nor usb)
so we will replace it first with our uboot.

Start a TFTP server at IP address 169.254.254.254, and
place the uboot.kwb file in the folder of the server.

Start the serial session and then power up the device.

As soon as you see text on the serial start pressing random
letter keys to stop the boot process.

If you see something like the following line you can proceed:

CE>>

Otherwise if text is still scrolling by you missed the
opportunity, pull the plug and try again.

write

printenv ethaddr

The uboot will write something like this:

ethaddr=00:50:43:00:02:02

This is the device's MAC address, also present in the sticker
under the device.

Write this down as we will need to add it in the
new uboot configuration.

Use the following commands to load the new uboot:

tftp 0x20000 u-boot.kwb

If the uboot confirms that the transfer was successful,
then you can write it to flash with the following commands:

nand erase 0 0x200000
nand write 0x20000 0 0x1c0000

if after the last command the uboot wrote
"xxxx bytes written: OK"
then it was written correctly and we can proceed.

If it did not go well, try again or ask assistence in forums.
Shutting down or rebooting at this time will brick
the device, to unbrick it you will need to use the kwboot
tool from a Linux PC or Virtual Machine.

Now write:

reset

and press enter, the device will reboot and you should see
again text scrolling by.
Press a random key to stop it, and now you should see

pogoplugv4>

We now add the MAC address back, write:

setenv ethaddr '00:50:43:00:02:02'

Confirm that the uboot has understood by writing

printenv ethaddr

If all looks ok, save the setting with

saveenv

At this point the uboot is configured, and we only need to load
the firmware in the flash memory.

Follow the steps below in "Firmware recovery procedure".

----
Firmware recovery procedure
----
The new uboot allows easy recovery from a bad firmware upgrade
where you can't access the device anymore over ssh or luci.

Take a USB flash drive formatted as FAT32, and copy the
initramfs image file in it (it will have "initramfs" in the
file name), then rename it as "initramfs.bin".

Insert the USB drive in the USB 2.0 port of the pogoplug
(the port at the top).

Power up the device, and wait for it to finish booting.

The uboot should find and load the "initramfs.bin"
from usb and if you are connected with serial you should
see the linux kernel boot log (text scrolling by).
Once it is done, press Enter and you will be greeted by
the OpenWRT banner.

If you were not connected with serial just wait a bit and,
you will be able to access it with ssh or luci web interface
(once you find its IP).

The recovery "initramfs" images are run from RAM, so you will
have to do a normal sysupgrade (firmware upgrade) to write
a firmware image to flash memory.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-01-09 22:06:55 +01:00
Mathias Kresin f5df635ccf kirkwood: sync image filename with boardname
Use <manufacturer>_<modelname> as image name.

Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin c9e2c35f46 kirkwood: use the generic board detect
Drop the target specific detection function in favour of the generic
one provided by base-files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin aa6f5f1787 kirkwood: use image metadata
Append and enforce image metadata. Remove the device specific image
checks, they are replaced by image metadata.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin a10ab9d843 kirkwood: fix nsa310b compatible strings
Use a destinct compatible string fro the nsa310b.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Mathias Kresin 18ea058258 kirkwood: fix compatible string in ib62x0 dts
There is no point in being that specifc in a generic dts covering a range
of boards. Keep only the the generic compat string to use it for a
devicetree based boardname.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Mathias Kresin 0ebdf0c1d3 kirkwood: drop support for orphaned boards
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Mathias Kresin d2e18dae28 kirkwood: cleanup image build code
Drop NAND_BLOCKSIZE, UBI_OPTS and UBIFS_OPTS. They are either used by
not supported filesystems or by the legacy image build code.

Add common used options/images to the default build code and override
the options where necessary.

Don't export the kernel image, it isn't required by any board.

While at it, change the file extension for the sysupgrade images to bin.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Mathias Kresin f0227af5d6 ipq806x: drop kernel 4.4 leftovers
Remove the kernel 4.4 specific devicetree source files.

Fixes: 3a3564ead5 ("ipq806x: remove v4.4 support")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:37 +01:00
David Bauer daae09f1e5 ar71xx: fix Archer C7v4 5GHz MAC-address
The TP-Link firmware uses (primary_mac-1) as MAC-address
for the 5GHz WiFi. This applies the same behaviour to LEDE.

Currently, the MAC-address is retrieved from eth1, which
does not exist on the Archer C7 v4. As a result from this,
every C7 v4 with LEDE carries the same MAC-Address on the 5GHz WiFi.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-01-09 22:05:46 +01:00
Chuanhong Guo a657978fe7 ramips: fix lenovo newifi-y1 switch and LED config
There are 3 ethernet ports on Y1. LAN1 on port1, LAN2 on port0 and WAN on
port4.

Use a standalone switch configuration to match this and use the switch
trigger so that LAN LED could indicate the connetction status for both
lan ports correctly.

This patch also drop the internet led configuration, because there is a
WAN led for port4 and eth0.2 isn't always used as WAN.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-01-09 22:05:46 +01:00
Mathias Kresin 6912e55e71 ramips: add missing soc compatibles to dts
Add SoC compatibles where missing.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:05:46 +01:00
Mathias Kresin 3326e36fa7 ramips: firewrt: indicate boot status via LED
Add the Firefly FireWRT gree power LED to diag.sh to indicate the boot
status via the power LED.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:05:46 +01:00
Gabor Juhos 82cc439976 ar71xx: remove obsolete '< KERNEL_VERSION(4, 4, 0)' check
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.4.0 is always
false. Remove the obsolete check from mach-rb4xx.c to clean up the code
a bit.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 21:33:19 +01:00