Commit Graph

16350 Commits (28a2901cbace14541e1da47fdbaf1ccc7dc9c027)

Author SHA1 Message Date
Felix Fietkau f1e085adfe ar71xx: add ath10k firmware to profile defaults where ath10k is used
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-22 16:06:39 +02:00
Felix Fietkau 39429b3d20 apm821xx: rework image build code for MyBook Live
Eliminate redundant mkfs calls, preparation for upcoming image build
core rework

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-22 12:49:57 +02:00
Felix Fietkau 3886644632 apm821xx: add DEVICE_DTS_DIR variable, remove redundant DEVICE_VARS entry
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-22 12:49:57 +02:00
Felix Fietkau 44c39d5812 apm821xx: add missing default profiles for subtargets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-22 09:48:12 +02:00
Christian Lamparter 9e0fd1b52a apm821xx: add support for the Netgear Centria N900 WNDR4700/WNDR4720
This patch adds support for Netgear Centria N900 WNDR4700/WNDR4720

hardware highlights:

CPU:	AMCC PowerPC APM82181 Rev. E at 1000 MHz (PLB=166, OPB=83, EBC=83 MHz)
	Security support, Boot ROM Location NAND wo/ECC 2k page (8 bits)
	32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory
Board:	AMCC APM82181 Evaluation Board, PCIE0/SATA1, 1*USB OTG
DRAM:	256 MB (ECC not enabled, 500 Mb/s, 32-bit, CL3)
NAND:	128 MiB (SLC, erase size: 128 KiB, page size: 2048, OOB size: 64)
ETH:	Atheros AR8327N Gigabit Switch (4 x LAN, 1 x WAN)
USB:	2 x 3.0 (Renesas uPD720202K8-711-BAA-A, firmware not included)
SATA:	1 x SATA-II 3.5" Hard Drive Bay for HDDs (DesignWare SATA).
WLAN1:	Atheros AR9380 5GHz 802.11an 3:3x3
WLAN2:	Atheros AR9581 2.4GHz 802.11bgn 3:3x3
SDCARD:	GL827L SD/MMC/MS Flash Card Reader (on internal dwc2 USB 2.0 host)
I2C:	GMT G781 (i2c-0 @ 0x4d - lm90 compatible temperature sensor)
	TC654    (i2c-0 @ 0x1b - Dual PWM fan Speed controller)

WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!

INFO: Since this device only has a NAND chip. I opted for going with
root.squashfs in a UBI volume. There's no squashfs/jffs2 image.

This target produces three images.
  a. netgear factory image
     This image can be used to flash the Netgear WNDR4700 via the
     firmware recovery mechanism and the web admin site.

     The bootloader can be instructed to do a firmware recovery via the
     # fw_recovery
     command. It will start a tftp server and listen on 192.168.1.1
     (the ipaddr variable in u-boot) for incoming, binary tftp clients.
     The firmware recovery mechanism is also started if any of the flash
     content which contains the kernel, device-tree definitions or the
     (fake)rootfs fails to verify or load.

  b. sysupgrade.tar image for sysupgrade
     An sysupgrade will replace the entire current LEDE installation
     with a newer version. This does include the kernel and the ubi rootfs
     partition. The configuration can be carried over automatically as well
     if desired.

     simply copy the sysupgrade.tar to a the WNDR4700 running LEDE and run:

     root@lede:~# sysupgrade sysupgrade.tar

     and let it reboot.

     Note: The devicetree flash area is NOT updated. Until the devicetree
	   definition is stable, this can lead to all sorts of hardware
	   detection problems! So make sure, if you experience issues: try
	   the fw_recovery. If you are unsure whenever this affects you:
	   test if you can reproduce your issue with the initramfs method.
	   As it will always have up-to-date device-tree definitions.

  c. initramfs image for TFTP (for development and testing)
     To use the initramfs method, follow the following steps:
       1) Move the "lede-apm821xx-netgear-WNDR4700-initramfs-kernel.bin"
	  file to to the root directory of your TFTP server.

       2) rename it to wndr4700.bin

       3) On the WNDR4700 - Hit Enter during u-boot and insert:
	  # tftp 400000 wndr4700.bin; run addtty; bootm 400000 -

     This will boot the LEDE image.

     Note: The default tftp server is 192.168.1.7, if you want to change it:
     # setenv serverip 192.168.8.7;

     Note2: The default address for the WNDR4700 is 192.168.1.1:
     # setenv ipaddr 192.168.8.8;

     Note: Connect you tftp server on the last LAN port (not the WAN)

Note: The firmware for the USB 3.0 Host chip is not included anymore.
Therefore the two USB 3.0 ports will not work without the
uPD7070x-firmware package installed.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-07-22 09:48:12 +02:00
Christian Lamparter 47eeb9f857 apm821xx: lm90 add thermal sensor interface support for device tree
From 912-hwmon-lm90-expose-to-thermal-fw-via-DT.patch:
"This patch adds to lm90 temperature sensor the possibility
to expose itself as thermal zone device, registered on the
thermal framework.

The thermal zone is built only if a device tree node
describing a thermal zone for this sensor is present
inside the lm90 DT node. Otherwise, the driver behavior
will be the same."

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-07-22 09:48:12 +02:00
Christian Lamparter b46e2a6d95 apm821xx: tc654: add driver for Microchip TC654/TC655 PWM fan controllers
This patch adds a hwmon driver for the Microchip TC654 and TC655
Dual SMBus PWM Fan Speed Controllers with Fan Fault detection.

The chip is described in the DS2001734C Spec Document from Microchip.
It supports:
	- Shared PWM Fan Drive for two fans
	- Provides RPM
	- automatic PWM controller (needs additional
	  NTC/PTC Thermistors.)
	- Overtemperature alarm (when using NTC/PTC
	  Thermistors)

The TC654 is used by the Netgear WNDR47X0 to control its
system fan.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-07-22 09:48:12 +02:00
Christian Lamparter dc7efaefb5 apm821xx: add support for the Western Digital MyBook Live Series
Hardware Highlights:

This patch adds support for Western Digital MyBook Live Series:
CPU: AMCC PowerPC  UNKNOWN (PVR=12c41c83) at 800 MHz (PLB=200, OPB=100, EBC=100 MHz)
     32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory
Board: Apollo-3G - APM82181 Board, 1*SATA
DRAM:  256 MB (2x NT5TU64M16GG-AC)
FLASH: 512 kB (SST 39VF040)
Ethernet: 1xRGMII - 1 Gbit - Broadcom PHY BCM54610

WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!

The MyBook Live Duo additionally features a 1x USB 2.0 host port
and can support a second hard-drive.

This target produces two images for a target.
 1. ext4 image
    The extracted/raw image can be directly installed on
    the internal HDD via "dd if=img.ext4 of=/dev/sdX".

    This can either be done in place with the stock MyBook Live
    firmware via ssh. Or by removing the HDD and writing the image
    with a different PC.

    The the compressed images are useful for sysupgrade.

 2. recovery.tar image for TFTP and Serial.

    extract the recovery.tar to a TFTP server directory.

    On the MyBook Live (Duo) serial port - Hit Enter during u-boot and insert:
    # setenv serverip 192.168.1.254; setenv ipaddr 192.168.1.1; run net_self

    Where 192.168.1.254 is your TFTP server.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-07-22 09:48:12 +02:00
Christian Lamparter d37d16488c apm821xx: sata_dwc_460ex: backport fixes and cleanups from 4.7
This patch fixes the sata_dwc_460ex SATA driver which is used
by the SATA controllers in the MyBook Live Series and WNDR4700.

The code was backported from the upstream kernel.
It can be dropped completely on 4.7+.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-07-22 09:48:12 +02:00
Christian Lamparter ea91ee13a7 apm821xx: dw_dmac: backport fixes and cleanups from 4.7
This patch fixes the dw_dmac dma engine which is used
by the SATA controllers in the MyBook Live Series and WNDR4700.

The code was backported from the upstream kernel.
It can be dropped completely on 4.7+.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-07-22 09:48:12 +02:00
Chris Blake a57d6e2d47 apm821xx: add support for the Cisco Meraki MR24
This patch adds support for the Cisco Meraki MR24 Access point
to the apm821xx target.

Board:		MR24 - Meraki MR24 Cloud Managed Access Point
CPU:		APM82181 SoC 800 MHz (PLB=200 OPB=100 EBC=100)
Flash size:	32MiB
RAM Size:	128MiB
Wireless:	Atheros AR9380 5.0GHz + Atheros AR9380 2.4GHz
Ethernet ports:	1x Gigabit Atheros AR8035

WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!

For flashing instructions, visit:
<https://github.com/riptidewave93/Openwrt-MR24/blob/master/README.md#flashing>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-07-22 09:48:12 +02:00
Chris Blake 3827ce2c3d apm821xx: add support for the apm821xx device target
This adds a new target for PowerPC APM82181 and APM82161
(464-based) boards, as well as adds support for the booke-wdt
watchdog package.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-07-22 09:48:12 +02:00
Christian Lamparter 39f3408732 ppc4xx: remove booke-wdt watchdog package
This patch gets rid of the booke watchdog kmod package.
Instead the affected boards will enable it in their
kernel configs.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-07-22 09:48:12 +02:00
Mathias Kresin e6a7e6ed25 lantiq: fix image creation of P2812HNUF3 & BTHOMEHUBV3A
Both devices were converted to the new image build code but still using
the LegacyDevice define. Therefore an image isn't created for the
mentioned devices.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-07-22 09:46:44 +02:00
Felix Fietkau d22fc1973c kernel: enable CONFIG_SND_PROC_FS by default (FS#54)
Some user space code relies on it

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-21 15:33:50 +02:00
Felix Fietkau c6c81351b7 ar71xx: add missing profile for the nand subtarget (FS#56)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-21 13:58:47 +02:00
Felix Fietkau 16209710d9 ar71xx: fix WNDR4300v1 / WNDR3700v4 build (FS#56)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-21 13:52:12 +02:00
Felix Fietkau ad323881df ar71xx: fix more image build code whitespace/tab issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-21 13:49:01 +02:00
Felix Fietkau 3d8c8d5e05 ar71xx: fix tab vs whitespace issue in image building code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-21 13:29:04 +02:00
Felix Fietkau 4d0f4f5e52 ar71xx: remove obsolete MultiProfile template code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-21 13:29:04 +02:00
Felix Fietkau 32727c409e mvebu: switch to the new image build code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-21 13:29:04 +02:00
Rafał Miłecki 60d2620253 kernel: update bcma backporting changes up to 4.8
This allows building bcm47xxsflash on ARM.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-07-20 13:42:42 +02:00
Rafał Miłecki d12e276cb0 kernel: backport patch for MTD_BCM47XXSFLASH dependency
This is required to update bcma without build breakage. One of bcma
patches changes BCMA_SFLASH dependency.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-07-20 13:00:14 +02:00
Felix Fietkau 7a175e2d44 ipq806x: clean up redundant initialization of core device image variables
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau cd243b1090 cns3xxx: remove obsolete jffs2 image build code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau eceb6b924a x86: remove obsolete reference to $(PROFILE)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau 2b4d21a3e6 mxs: unconditionally install kernel images/dtb files into rootfs (needed by boards)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau 650afe412b kirkwood: remove obsolete code for including kernel/dtb in rootfs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau edea59fd99 omap: remove obsolete code for including kernel/dtb in rootfs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau 1625e57772 omap: remove obsolete kernel version support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau 0538bbdc4d kirkwood: remove obsolete ubinize.cfg file
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau 5d4b044955 kirkwood: clean up redundant variables in the image building code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau cfd1ef4b90 kirkwood: get rid of useless ubifs/ubi option variables
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau ab92f57684 lantiq: convert remaining xway NAND devices to new image build code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau f12e964733 lantiq: convert AVM xrx200 devices to new image build code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau bdfed2a2c3 lantiq: convert simple xrx200 devices to new image build code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau 22c0206044 lantiq: add image build template for NAND devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau 8058e4778b lantiq: simplify image building code
Specifying the device profile in PROFILES is unnecessary, and for all
devices the DEVICE_PROFILE variable matched the device name.
Get rid of this useless variable and set DEVICE_DTS to $(1)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau cc88df1a38 lantiq: fix building NAND images in default config
Remove remaining references to $(PROFILE)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau ceee47ba64 lantiq: disable jffs2 support on xrx200
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau 5a92e049d5 kernel: remove obsolete patch adding usb_find_device_by_name
ledtrig-usbdev does not need it anymore

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Rafał Miłecki 5ea8756766 ledtrig-usbdev: use upstream function for iterating USB devices
This will allow us to drop LEDE patch adding usb_find_device_by_name.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-07-20 10:13:50 +02:00
Jo-Philipp Wich e633a1b48f ar71xx: fix default network config of WZR-HP-G300NH and CR3000
The network defaults for the WZR-HP-G300NH and CR3000 models wrongly set the
lan interface to a vlan tagged device while the switch was set up in untagged
mode, leading to broken lan side ethernet connectivity by default.

Fix the issue by emitting untagged interfaces, consistent with the switch
setting on the device.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-20 00:21:48 +02:00
Zhao Gang d963ddf042 ar71xx: add support for gl-ar300m
This add initial support for gl-ar300m router.
Product page: http://www.gl-inet.com/ar300m/

Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
2016-07-20 00:21:48 +02:00
Florian Klink 4221288db7 x86/generic: enable CONFIG_SATA_VIA
This enables support for VIA SATA.
2016-07-19 14:26:32 +02:00
Daniel Golle 022698c6c9 kernel: backport cosmetic UBIFS patches to kernel 4.1
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-07-19 00:31:34 +02:00
Daniel Golle fc90851df0 kernel: backport yet another cosmetic ubifs patch
On UBI-enabled devices using squashfs as their rootfs an error
message like
UBIFS error (ubi0:3 pid 1): init_constants_early: too few LEBs (12), min. is 17
was thrown while probe-mounting the rootfs which later on succeeds and
thus shouldn't alert the user.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-07-19 00:31:27 +02:00
Daniel Golle f082d94235 oxnas: add kmod-ledtrig-timer to default package set
It is needed for preinit/failsafe indications to work.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-07-18 20:05:15 +02:00
Daniel Golle 8880497382 oxnas: use DHCP by default on ethernet interface (lan)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-07-18 19:37:43 +02:00
Daniel Golle b05125c775 oxnas: sync kernel config-4.1 with changes made to config-4.4
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-07-18 18:59:53 +02:00
Daniel Golle caf36d199d oxnas: add DTB for Akitio devices in patches-4.1
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-07-18 18:45:03 +02:00
Daniel Golle c5ec5e1f7f oxnas: revert to kernel 4.1
A bug resulting in the NAND not being detected by newer kernels has
kept me sleepless for months and yet I wasn't able to discover the
cause.
Bring back patches and files for 4.1 until this has been resolved.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-07-18 18:35:32 +02:00
Josh Bendavid 9780b2dd93 ipq806x: add patch for kernel compiler flags
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
2016-07-17 17:29:12 +02:00
Josh Bendavid 15bcda4be6 ipq806x: change compiler flags to arm cortex-a15
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
2016-07-17 17:29:12 +02:00
Jo-Philipp Wich b051ac76e8 ramips: mt7621: add missing kernel symbol
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-16 13:59:12 +02:00
Stephen Walker 900da27c91 ar71xx: add software transmit timestamp support
Add software transmit timestamp and ethtool (-T) timestamp support

Signed-off-by: Stephen Walker <stephendwalker+github@gmail.com>
2016-07-15 14:19:32 +02:00
Felix Fietkau a176168a85 ar71xx: define wmac reset function for QCA955x
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-15 14:19:06 +02:00
Felix Fietkau 8e2764ce9b image.mk: clean up redundant code related to DEVICE_DTS
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-15 14:14:11 +02:00
Rafał Miłecki c940ccedd8 bcm53xx: image: don't suppress "mv" command echoing
We call all commands normally, with standard echoing. It's useful for
debugging with V=s. Don't make lzma compression an exception, it's a bit
confusing this way.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-07-14 11:31:26 +02:00
Felix Fietkau b3b797076e bcm53xx: simplify image building code
Use append-ubi template for ubinize, remove mkfs override

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-14 10:27:45 +02:00
Felix Fietkau dbc416b6ec bcm53xx: remove duplicate template data from the image makefile
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-14 10:27:30 +02:00
Felix Fietkau e0ed6ec667 image: clean up UBI related device variable definitions
Move UBI related variable export to core, since the variables are used
by a core Build/ template

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-14 10:27:30 +02:00
Felix Fietkau 1729a089fe ipq806x: remove obsolete UBINIZE_OPTS variables
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-14 10:27:30 +02:00
Piotr Dymacz d2c9b169b3 ar71xx: add support for jjPlus JWAP230
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers

Default configuration:

- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space

Flash instruction (do it under U-Boot, using RS232):

1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
Piotr Dymacz 2923b334e5 kernel/mtd: add support for EON EN25Q128
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
Piotr Dymacz e767980eb8 ar71xx: add support for Wallys DR531
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers

Default configuration:

- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
Felix Fietkau 70cf8c3048 ar71xx: fix build error when initramfs is disabled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-13 18:41:25 +02:00
Hauke Mehrtens efa1960abb kernel: update kernel 4.4 to version 4.4.15
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-07-13 15:39:15 +02:00
Felix Fietkau d6b3b44d97 ar71xx: fix a legacy image porting issue
Get rid of remaining IMAGE_PROFILE references and move template calls
the right place

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-13 13:59:24 +02:00
Lucian Cristian 2ea76bdf04 x64: add legacy IDE, fix VirtualBox bug #84 and Fujitsu Futro S550-2
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2016-07-12 15:44:34 +02:00
Alexey Brodkin 4ebb1950be kernel: Add upstream fix for module loading
Instead of disabling unwinding entirely this upstream patch
just disables generation of async unwind tables.

Once the patch in question lands in stable 4.4 tree this change
essentially must be removed (otherwise patch application will fail).

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2016-07-11 14:19:47 +02:00
Alexey Brodkin 697ee80388 Revert "linux: arc: disable kernel unwinding to fix modules loading"
This reverts commit acd41539d6.

There's a fix in upstream that will at some point land in 4.4 stable as
well so we'll get rid of this hack and with the next commit will apply
upstream fix.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2016-07-11 14:19:47 +02:00
Alexey Brodkin 055ba75f92 linux/archs38: Add wireless AP capabilities similarly to axs101
Now when ath9k-htc USB dongle works with axs103 in OHCI mode
quite fine adding corresponding features to default configuration.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2016-07-11 14:19:47 +02:00
Daniel Dickinson a775c5db46 ar71xx: Fix PowerCloud CAP324 No Cloud title
CAP324 nocloud was missing (No-Cloud) in description

Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
2016-07-11 14:19:47 +02:00
Michael Lee 9062c4fe99 ramips: modify audio kernel module and add dma options
* add gdma and hsdma kernel modules
* i2s support all ramips targets except rt288x
* i2s need gdma to transfer data
* add simple audio kernel module. it support device tree binding

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
Michael Lee c3e420f28c ramips: Add support for D-Link DCH-M225
D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash,
3.5mm audio out support. but no ethernet and usb ports.
so you must default enable wifi.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
Michael Lee 36d98e6c7a ramips: add MT7620 pinmux bits for mdio as refclk
The MT7620 uses a 2 bit wide configuration of the mdio.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
Michael Lee 0460e9ffca ramips: enable MTD_SPLIT_SEAMA_FW for mt7620
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
L. D. Pinney cf8c77be6b ramips: Add support for the NixCore X1 Module
The NixCore X1 is a Ralink/MediaTek rt5350 WiFi Module.

http://nixcores.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Drew Gaylo <drew@nixcores.com>
2016-07-11 14:19:47 +02:00
Rene Treffer 8876575601 ramips: fix partition size for RT5350F-OLINUXINO
The partition size is wrong, leading to out-of-disk-space even on no/moderate use.

Upstream fix from vendor: 2f25eb57ed
Suggested fix for openwrt: https://dev.openwrt.org/ticket/20321

Signed-off-by: Rene Treffer <treffer@measite.de>
2016-07-11 14:19:47 +02:00
John Crispin 252f751611 ramips: fix usb phy initialisation
this broke usb20 device detection.

Signed-off-by: John Crispin <john@phrozen.org>
2016-07-11 14:19:46 +02:00
Yousong Zhou 09907170dd ar71xx: base-files: remove the now unneeded 09_fix-seama-header
It was intended as a workaround when jffs2 eof mark was included in the
checksum calculation in seama header.  When qihoo-c301 support was
introduced the board name was not inserted into the case list (because I
was not aware of it's existence), but the issue was fixed by excluding
the jffs2 marker as part of the checksum data

Now we are at it, drop it.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2016-07-11 13:26:36 +02:00
Yousong Zhou 8d0ec3e672 ar71xx: image: fix typo in MTDPARTS def for qihoo-c301
Reported-by: Syrone Wong <wong.syrone@gmail.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2016-07-11 13:26:35 +02:00
Yousong Zhou 6d6db4ff7b ar71xx: image: seama: fix making factory and sysupgrade image
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2016-07-11 13:26:34 +02:00
Álvaro Fernández Rojas 20402106a3 brcm2708: update linux 4.4 patches to latest version
As usual these patches were extracted and rebased from the raspberry pi repo:
https://github.com/raspberrypi/linux/tree/rpi-4.4.y

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-07-09 16:29:18 +02:00
Jonas Gorski eae812ddb6 brcm63xx: fix image generation with offsets/blocksizes != 64K
Defer the CFE_EXTRAs evaluation to allow overriden BLOCK_SIZE and
IMAGE_OFFSET take effect, and replace the unused IMAGE_SIZE with
IMAGE_OFFSET in DEVICE_VARS.

This fixes image generation for targets using different offsets or
blocksizes.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-07-09 13:41:53 +02:00
Jonas Gorski 0bed85bbca brcm63xx: fix CVG834G compatible string
The CVG834G claimed to be a BCM6348, but is actually BCM3368. Since we
don't test against it, this was harmless.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-07-09 13:41:50 +02:00
Felix Fietkau fac693441f bcm53xx: fix kernel config after USB2 PHY driver backport
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-08 13:45:36 +02:00
Rafał Miłecki 1692c71564 bcm53xx: use upstream fix simplifying USB power GPIO usage
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-07-07 15:07:02 +02:00
Rafał Miłecki c74c227e5b bcm53xx: backport driver for Northstar's USB 2.0 PHY
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-07-07 14:50:17 +02:00
Rafał Miłecki e71fffed64 bcm53xx: backport BCM5301x patches from 2016-07-06
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-07-07 13:54:55 +02:00
Felix Fietkau 201dbb9fe8 ramips: fix build error in ubnt-erx initramfs factory image
Build initramfs kernel image, but skip factory image if initramfs size
is too big.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-06 10:12:37 +02:00
Alexey Brodkin aba6de38d2 usb: Remove annoying warning about bogus URB
When USB Wi-Fi dongle based on Atheros AR9271 is connected to OHCI
(USB 1.1) controller following warnings flood debug console:
------------------------>8---------------------------
usb 1-1: new full-speed USB device number 2 using ohci-platform
usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested
usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008
------------[ cut here ]------------
WARNING: CPU: 0 PID: 4 at drivers/usb/core/urb.c:450
usb_submit_urb+0x162/0x404
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
Modules linked in:
CPU: 0 PID: 4 Comm: kworker/0:0 Not tainted 4.6.3 #10
Workqueue: events request_firmware_work_func

Stack Trace:
  arc_unwind_core.constprop.1+0x94/0x10c
---[ end trace 2249b79eac9991d1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 4 at drivers/usb/core/urb.c:450 usb_submit_urb+0x162/0x404
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
Modules linked in:
CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G        W       4.6.3 #10
Workqueue: events request_firmware_work_func

Stack Trace:
  arc_unwind_core.constprop.1+0x94/0x10c
---[ end trace 2249b79eac9991d2 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 4 at drivers/usb/core/urb.c:450 usb_submit_urb+0x162/0x404
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
Modules linked in:
CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G        W       4.6.3 #10
Workqueue: events request_firmware_work_func

Stack Trace:
  arc_unwind_core.constprop.1+0x94/0x10c
---[ end trace 2249b79eac9991d3 ]---

...
------------------------>8---------------------------

With removed warning Wi-Fi dongle works properly.

Even though this is not the best solution it gets us a working Wireless
AP. Anyways new discussion was started in linux-usb mailing list to find
a proper solution instead of that hack.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2016-07-05 22:59:14 +02:00
Alexey Brodkin 2005732ea7 linux/archs38: Disable USB 2.0
As of today USB 2.0 (AKA EHCI) doesn't work on axs103 board
and so there's no reason to build corresponding software for it.

Once USB 2.0 gets fixed on axs103 thi patch might be reverted.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2016-07-05 22:59:14 +02:00
Ben Mulvihill 1cc092f72b lantiq: mac address setting on BTHOMEHUBV3A
Rename uboot environment partition on BT Home Hub 3A so that mac address
setting works correctly.

Also, the mac address field in the ath9k calibration data is not used,
and should not be referenced in the dts.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
2016-07-05 22:59:14 +02:00
Sergey Sergeev 17ee6bb8f3 tools: add kernel2minor utility for Mikrotik devices
This patch adds support of Mikrotik yaffs2 filesystem image for kernel file
and tools/kernel2minor package.
We neede this to boot kernel through RouterBoot on new Mikrotik NOR flash devices.

Signed-off-by: Sergey Sergeev <adron@yapic.net>
2016-07-05 22:59:14 +02:00
John Crispin eca1021e5c ramips: fix buffalo wmr-300 lan port
Signed-off-by: John Crispin <john@phrozen.org>
2016-07-05 22:59:14 +02:00
John Crispin 8fe69e4d42 ar71xx: fix nand device profile
Signed-off-by: John Crispin <john@phrozen.org>
2016-07-05 22:59:14 +02:00
John Crispin 2c9073282d ramips: fix MT7621 gsw handling
based on https://forum.openwrt.org/viewtopic.php?pid=323671#p323671

Signed-off-by: John Crispin <john@phrozen.org>
2016-07-05 22:59:13 +02:00
John Crispin 69a626b441 ramips: fix mt7621 SoC detection
Signed-off-by: John Crispin <john@phrozen.org>
2016-07-05 22:59:13 +02:00
Rafał Miłecki eaf0d22421 bcm53xx: calculate Seama MD5 using content of kernel partition
We don't want checksum to cover any part of UBI as even its part with
SquashFS may be changed due to e.g. flash wearing.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-07-04 12:32:12 +02:00
Rafał Miłecki 3c014dc306 Revert "bcm53xx: use uncompressed zImages"
This reverts commit b3be33f135.

CFE is known to fail in some non-standard cases, e.g. when using kernel
or format different that what was tested by Broadcom. This kernel change
triggered some problem with booting OpenWrt kernel stored in Seama.

As long as Seama checksum was covering enough data, it was working fine.
We need to change it however, because calculating MD5 over part of UBI
containing SquashFS is unsafe. UBI may move PEBs depending on flash
wearing level which would break CFE booting the image.

For some reason this kernel change was breaking CFE. Calculating MD5
over 0x47ffc0 B data or less (there is 0x40 B long header) was stopping
booting process at:
Starting program at 0x00008000

As our kernel is usually 0x3fffc0 B it was affected by this problem.

Reverting this change fixes sysupgrade (which already uses kernel size
for MD5 calculation) and will allow us to adjust "fixseama" command call
on the first boot.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-07-04 12:32:12 +02:00
Felix Fietkau 39a229ed4b ipq806x: enable ath10k firmware for 988x, 99x0 and 9984 by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-04 11:41:32 +02:00
John Crispin d09f0045ea ramips: fix up switch settings for Sitecom WL-351 v1 002
Pinmux for rgmii needs to be set to rgmii, not gpio.
Hide the ESW switch on boot (using new rgmii esw devicetree attribute).
Also add a Sitecom-specific profile, since the image needs to include
the rtl8366 kernel driver.

Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
2016-07-03 08:00:26 +02:00
Felix Fietkau e892472b1e x86: enable kmod-igb on 64-bit by default
It is used on APU2 devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-03 19:43:18 +02:00
Felix Fietkau d5ee23ee27 x86: stop relying on hexdump for image build signature
Use perl to generate random number instead.
See https://github.com/freifunk-gluon/gluon/issues/811

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-03 18:39:11 +02:00
Felix Fietkau de165b66be imx6: fix redundant PROFILES overrides in image makefile
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-02 19:34:19 +02:00
Felix Fietkau 7e7a31e682 imx6: fix build breakage introduced in 9e41c3f54e
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-02 19:34:19 +02:00
Felix Fietkau 61d82e7b02 imx6: fix image makefile indentation for Device/ sections
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-02 19:34:19 +02:00
Hauke Mehrtens 1d15a96b29 kernel: fix build of kmod-udptunnel4 and kmod-udptunnel6
The kernel config option CONFIG_NET_UDP_TUNNEL is not visible and can
not directly be activated. When kmod-udptunnel4 or kmod-udptunnel6 are
build these packages could be empty when no other kernel module selects
CONFIG_NET_UDP_TUNNEL.

Reported-by: Baptiste Jonglez <baptiste@bitsofnetworks.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-07-02 18:35:58 +02:00
Sergey Sergeev c312cef223 ar71xx: spi-rb4xx fix.
In new kernels we should use clk_prepare_enable instead of clk_enable
since clk_enable does not make proper initialization that leads
to rise WARN_ON messages and not working spi bus on the device.

Signed-off-by: Sergey Sergeev <adron@yapic.net>
2016-07-02 10:16:17 +02:00
Felix Fietkau f9e7ffe73b ar71xx: prevent spurious ethernet resets from dma hang check false positives
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-02 10:30:58 +02:00
daniel f576ff05a1 kernel: Fix ipv6 mc snooping if bridge has no ipv6 address
This patch is a backport for current LEDE 4.4 Kernels.
It is already upstream, for linux-next and stable.
The initial commit message is below:

The bridge is falsly dropping ipv6 mulitcast packets if there is:
 1. No ipv6 address assigned on the brigde.
 2. No external mld querier present.
 3. The internal querier enabled.

When the bridge fails to build mld queries, because it has no
ipv6 address, it slilently returns, but keeps the local querier enabled.
This specific case causes confusing packet loss.

Ipv6 multicast snooping can only work if:
 a) An external querier is present
 OR
 b) The bridge has an ipv6 address an is capable of sending own queries

Otherwise it has to forward/flood the ipv6 multicast traffic,
because snooping cannot work.

This patch fixes the issue by adding a flag to the bridge struct that
indicates that there is currently no ipv6 address assinged to the bridge
and returns a false state for the local querier in
__br_multicast_querier_exists().

Special thanks to Linus Lüssing.

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
2016-06-30 22:48:39 +02:00
Yousong Zhou 559a7d1177 ar71xx: seama: fix making factory images
rootfs part needs to be aligned to erase block size which is passed as
the 6th argument to Image/Build/Seama  and is now 65536 since commit
commit 5119ee9 "ar71xx: fix bogus hardcoded kernel image size for Seama
images (fixes #20585)", but $(($(6) - 64)) still assumes that the
argument is a limit on kernel partition size, i.e. 1310720, so the
generated factory image is wrong in that the kernel will fail to find
the rootfs (FlySpray link at [1])

This patch will workaround it with the following steps

1. Calculate the required space for seama header and META data in step 5
2. Pre-padding 64 bytes to lzma-compressed loader
3. Generate correctly padded image-$(2).tmp
4. Strip out the padding
5. Seal it with seama utility

While at it convert seama to new build method

[1] FS#35 - mynet-n750 factory images don't find root partition,
    https://bugs.lede-project.org/index.php?do=details&task_id=35

Reported-by: Steven Haigh <netwiz@crc.id.au>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2016-06-30 22:48:39 +02:00
Yousong Zhou ea284d704b ar71xx: image: unify indentation with 2 whitespaces
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2016-06-30 22:48:39 +02:00
Yousong Zhou e3cf2cc1c6 ar71xx: image: remove duplicate IMAGES definition
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2016-06-30 22:48:39 +02:00
Yousong Zhou 11cbe29833 ar71xx: hiwifi-hc6361: move packages selection to generic.mk
Remove kmod-crypto-deflate and kmod-ledtrig-gpio as the device works the
same by default without them

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2016-06-30 22:48:39 +02:00
John Crispin 2dc9beddc0 ramips: disable the WP pin on the SDK mmc driver
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-30 22:48:39 +02:00
John Crispin 81add8f753 ramips: fix pinmux typo
Reported-by: Joy Kicer <joykicer@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-30 22:48:39 +02:00
Daniel Dickinson e408abd7fb kernel: Add option to make using filesystem ACL support the default
This adds a configuration options that allows to make filesystem ACL support
the default in the kernel, except for old nfs.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
2016-06-30 22:48:39 +02:00
Matthias Schiffer 0a0caa2656
ramips: set correct LAN/WAN MAC addresses on DIR-860L B1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Matthias Schiffer 103ed00cfb
ramips: add button support and make LEDs known to userspace for DIR-860L B1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Matthias Schiffer fa9811814a
ramips: fix fixseama call on first boot
Commit "kernel: mtdsplit: calculate kernel partition precisely for Seama"
changed the kernel partition to only contain the kernel itself and not
the Seama header. Adjust the fixseama call to match what is used on
brcm53xx.

This fixes failing to boot a second time after flashing the factory image
on the affected devices.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Jo-Philipp Wich 6ee66ae075 ar71xx: further legacy image build fixes
- Add missing macro to trigger the generation of 64k padded squashfs images
- Revert Zcomax image generation to use the prepared 64k squashfs image

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-27 15:15:49 +02:00
Felix Fietkau 2270fc5947 Revert "lantiq: enable SMP for XRX200"
This reverts commit cc3bfdb62f.

Apparently the ethernet driver is not SMP safe, as reported in
https://bugs.lede-project.org/index.php?do=details&task_id=27

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-27 13:06:56 +02:00
Felix Fietkau be08fdd007 ar71xx: disable pdata->use_flow_control for QCA9558
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-27 12:12:40 +02:00
Felix Fietkau 75b2105cd3 ar71xx: rename ethernet pdata->builtin_switch to use_flow_control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-27 12:12:40 +02:00
Jo-Philipp Wich 8d1218ca73 ar71xx: merge profiles into image building code
- Remove old style device profiles and convert them to device definitions
  within the image building code

- Fix the legacy build macros for the changed eval depth in the legacy
  image build wrapper

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-27 11:10:15 +02:00
Hauke Mehrtens dc140e00a9 kernel: fix missing break in ubi auto-mounting patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-27 08:10:36 +02:00
Hauke Mehrtens 459a8afff1 kernel: remove igb: Fix Null-pointer dereference patch
This patch is already included in the Linux mainline kernel since
v3.15, remove it from LEDE, see the lines directly before this patch.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-26 18:47:29 +02:00
Hauke Mehrtens bf32177a1d kernel: remove full cache flush in fuse_copy_do() for MIPS
This patch was introduced in commit r16412 for the brcm47xx target only
and then moved to generic in commit r32395. It was initially added
because of ticket #5186 and should fix some problems with fuse file
systems and MIPS caches. The commit comment in r32395 says that this a
generic problem in MIPS CPUs, but does not name any specifics about
that. There was a fix added to kernel 2.6.21 in commit commit
7575a49f20 "[MIPS] Implement flush_anon_page()." that should fix this
problem, but that was already available before both commits were done
to OpenWrt.

I just tested fuse with ntfs.3g without this patch on a BCM4704
(BMIPS3300 V0.6) SoC and haven't seen any problems. Someone reported
that removing this patch improves some fuse operations by 5 times on
some modern MIPS cores.
My test was only a simple "dd if=/dev/zero of=/mnt/zero bs=5000" to an
USB stick.

This patch removes the patch to OpenWrt, because I assume that it is
not needed any more and Felix, the orginal author, also thinks so.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-26 18:22:23 +02:00
Hauke Mehrtens 2abb02419d kernel: remove one of two patches deactivating broken vdso support on mips
The patch target/linux/generic/patches-4.4/206-mips-disable-vdso.patch
should be sufficient.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-26 18:22:23 +02:00
Hauke Mehrtens 84d489f64f kernel: update to version 4.4.14
Changelog: https://cdn.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.4.14

Some manual changes to target/linux/generic/patches-4.4/610-
netfilter_match_bypass_default_checks.patch were needed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-26 18:20:37 +02:00
Felix Fietkau 3bf3512673 Revert "ar71xx: prevent spurious ethernet resets from dma hang check false positives"
This reverts commit 3d58d7f053.
2016-06-26 16:53:11 +02:00
Felix Fietkau 3d58d7f053 ar71xx: prevent spurious ethernet resets from dma hang check false positives
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-26 11:21:17 +02:00
Felix Fietkau 26b8db2537 ar71xx: enable flow control for ethernet MACs with built-in switch
Should fix LAN speed issues on some devices. This is an updated version
of the previously reverted commit with the same name.
It improves the check for MACs connected to a built-in switch

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-26 11:21:17 +02:00
John Crispin 3874773503 Revert "ar71xx: fix legacy image building"
This reverts commit 59e98b27c9.

and

Revert "ar71xx: merge profiles into image building code"

This reverts commit 636089ead6.

these are still causing issues

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-23 19:33:31 +02:00
Jo-Philipp Wich 59e98b27c9 ar71xx: fix legacy image building
After the conversion from legacy device profiles to the newer profile
information embedded in the image building code, the legacy recipes got
triggered twice with different eval depths, leading to shell syntax errors
when processing certain images.

The double processing was caused by the remaining Image/Build macro in
legacy.mk which serves as main entry point for the new style image build code
in conjunction with the newly introduced LegacyDevice/* macros which caused
the legacy image build fallback code to kick in.

In order to fix the issue, rework all legacy macros to work under the legacy
image build wrapper and remove the Image/Build macro of legacy.mk to prevent
legacy profiles getting executed in the context of the new build code.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-24 13:43:40 +02:00
John Crispin 636089ead6 ar71xx: merge profiles into image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-22 19:32:06 +02:00
Roger Pueyo Centelles 5fba0f0c0c ramips: add suport for ZBT APE522II
The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has
64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with
802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac
MT7612E-based 5 GHz radio.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-06-22 19:32:06 +02:00
Adrian Panella 184087f4f1 ipq806x: enable ieee80211 phy hotplug and patch macaddress
Calibration data for QCA99x0 in this device has bogus macaddress.
The data cannot be modified directly, as it breaks checksum control.
Instead change the macaddress from phy add hotplug event.

Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-06-22 19:32:06 +02:00
Hauke Mehrtens f97ad870e1 squashfs4: use upstream xz compression header format
In the upstream kernel and the upstream squashfs4 tools the xz
compression header looks the following:
struct disk_comp_opts {
        __le32 dictionary_size;
        __le32 flags;
};

We added some other members and also moved some existing members. Place
the members which are already in upstream header at the same position
as in that kernel and add our own at the end. The kernel should not
have a problem when there are some additional members and just ignore
them.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-22 19:32:06 +02:00
Mathias Kresin f080cfab72 lantiq: fix network in failsafe
So far the network in failsafe is setup only for one board. Use the
eth0 interface as lan interface for all boards for now.

If a board has its lan interface(s) on another eth, a special
handling based on the board name can be added.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-06-22 19:32:06 +02:00
Alexey Brodkin acd41539d6 linux: arc: disable kernel unwinding to fix modules loading
With update of binutils for ARC (this is now based on upstream 2.26)
we noticed issues with loadable kernel modules.

Something like that was happening:
--------------------->8-------------------
mbcache: unknown relocation: 49
insmod: can't insert './mbcache.ko': invalid module format
--------------------->8-------------------

More details could be found in that discussion in binutils mailing list:
http://thread.gmane.org/gmane.comp.gnu.binutils/74662

As of now the simplest work-around is to disable in-kernel unwinder
for now. That will at least allow us to use modules again.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: John Crispin <john@phrozen.org>
2016-06-22 19:32:06 +02:00
Sven Eckelmann 776613eeba ipq806x: Fix typo in Qualcomm device names
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-06-22 19:32:06 +02:00
Oswald Buddenhagen 9759fde40a lantiq: add support for ARV7506PW11 (Alice/O2 IAD 4421)
Ethernet, ADSL2+ and LEDs are fully functional.

Supporting the two TAE ports and SIP gateway was not attempted.

The WiFi is unreliable, due to experimental support for rt35xx family
devices by the rt2800pci driver.

Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
[rebase to LEDE HEAD]
[switch to normal image instead of brnboot image]
[remove not required pinmux child nodes keys, leds, ebu, exin, pci_in and pci_out]
[remove switch_rst pinmux child node (no support for hw reset in driver/setting a default GPIO value in DT]
[enable usage of the wireless LED]
[fixup mac address configuration]
Sgned-off-by: Mathias Kresin <dev@kresin.me>
2016-06-22 19:32:06 +02:00
Yousong Zhou b67066b8fa ar71xx: hiwifi-hc6361: lift size limit on kernel and rootfs parts
The patch has been run-tested and the relevant dmsg logs are as the
following

    [    0.762447] Creating 5 MTD partitions on "spi0.0":
    [    0.767217] 0x000000000000-0x000000010000 : "u-boot"
    [    0.775139] 0x000000010000-0x000000020000 : "bdinfo"
    [    0.781014] 0x000000020000-0x000000fe0000 : "firmware"
    [    0.810558] 2 uimage-fw partitions found on MTD device firmware
    [    0.815043] 0x000000020000-0x000000170000 : "kernel"
    [    0.821925] 0x000000170000-0x000000fe0000 : "rootfs"
    [    0.827587] mtd: device 4 (rootfs) set to be root filesystem
    [    0.831937] 1 squashfs-split partitions found on MTD device rootfs
    [    0.837983] 0x0000005c0000-0x000000fe0000 : "rootfs_data"
    [    0.845621] 0x000000fe0000-0x000000ff0000 : "backup"
    [    0.851445] 0x000000ff0000-0x000001000000 : "art"

While at it, convert to new build method

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2016-06-22 19:32:06 +02:00
Ben Whitten b7baaaf782 kernel: Move append-dtb to common image-commands
This build step is used by various targets, move it to a common section.

Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
2016-06-22 19:32:06 +02:00
Daniel Gimpelevich 34fdfbf328 lantiq: Slow down SPI flash on the DGN3500
The bootloader uses 30 MHz as the SPI frequency for flash on the Germany and
North America models, and 50 MHz for it on the worldwide model, but the Lantiq
SPI driver in OpenWrt and LEDE may access the flash differently such that
writes are capped at 20 MHz, leading to read errors reported on the worldwide
model at 30 MHz.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Acked-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2016-06-22 19:32:06 +02:00
John Crispin f054e82bdc lantiq: remove gr7000 support
this seems to have never worked as the wrong SoC is selected

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-22 19:32:06 +02:00
Pavel Kubelun 823242185b ipq806x: add initial support for Netgear R7800
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-06-22 19:32:06 +02:00
Pavel Kubelun 9bf3ddcb2a ipq806x: move ath10k firmware selection into device profiles
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-06-22 19:32:06 +02:00
Pavel Kubelun 4cd67a4f21 ipq806x: move smb208 nodes into a regulator subnode
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-06-22 19:32:05 +02:00
Hauke Mehrtens 84b3d92180 lantiq: make EASY80920 work with both chip versions
The EASY80920 is available with the A1X and the A2X chip version
depending on the board version. Add both firmware versions to device
tree and make the driver load the correct version depending on the chip
version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-21 21:58:59 +02:00
Hauke Mehrtens 7f5b8cc376 lantiq: use new partition layout for EASY80920NAND
This matches the EASY80920NAND boards with UGW.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-21 21:58:59 +02:00
Hauke Mehrtens 8bfa230e9f lantiq: build fullimage.img for EASY80920NAND
This image format is used by Lantiq's / Intel's UGW version 6.1 to 7.1.
These images can be flashed onto a board with the SoC vendor boot
loader as a replacement for the vendor firmware.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-21 21:58:59 +02:00
Hauke Mehrtens ecdfbeae85 lantiq: remove patch adding support for building without reset controller
The lantiq kernel arch code selects CONFIG_RESET_CONTROLLER always, so
it is always selected when the lantiq target is build. we do not need
support for unselected CONFIG_RESET_CONTROLLER option.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-21 21:58:59 +02:00
Álvaro Fernández Rojas 63cb2fb88d brcm2708: properly detect the Raspberry Pi Zero
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-21 20:17:38 +02:00
Álvaro Fernández Rojas a95d64a269 brcm63xx: simplify block size and image offset options
Instead of having CFE_EXTRAS for every device that need specific block sizes
and image offset, let's define a couple of vars which can be customized for
each device.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-21 16:42:47 +02:00
Álvaro Fernández Rojas 13253fbcbd brcm63xx: add sysupgrade images
Some devices require padded images in order to prevent CFE from flashing them
to the wrong offset.
For small flashes (4/8) this is no big deal, but for larger flashes (16/32) this
implies 8 and 16 MB images, which is way too large and some devices aren't
capable of flashing them through sysupgrade.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-21 16:42:44 +02:00
Ben Mulvihill 7df43d88ec lantiq: fix typo in new image generation
Fix typo in commit a6f7536a73
(new image generation)

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
2016-06-21 13:49:54 +02:00
Jonas Gorski d61d82e3d3 brcm63xx: merge DSL-274X-F1 profiles
The only difference is a field in the image tag header, so just define
two images for it instead of treating them as separate devices.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-06-21 09:23:22 +02:00
Jonas Gorski a89f5e795a brcm63xx: move the bootargs into the dtb files
Instead of using a fixed commandline, allow one per device.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-06-21 09:23:22 +02:00
Jonas Gorski 80403e4558 brcm63xx: use upstreamed compatible name for the periph intc
This makes the eventual migration to bmips easier, as dts files
will require less changes.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-06-21 09:23:22 +02:00
Daniel Gonzalez 29444e4754 brcm63xx: fix external IRQs
External IRQs are currently broken, fix the BCM6345_EXT_IRQ driver.

Since the adoption of the new driver irq-bcm6345-ext, in Chaos Calmer,
external IRQs don't work. It seems there were some minor errors at the initial
development of the driver.

This patch fixes the ticket https://dev.openwrt.org/ticket/21613

Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-06-21 09:23:21 +02:00
Álvaro Fernández Rojas 6b5f6d6601 brcm63xx: fix single profile selection
Fixes commit c6990347.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-06-21 09:23:21 +02:00
Rafał Miłecki a180f90518 bcm53xx: backport BCM5301X patches for SRAB
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-06-20 23:07:31 +02:00
Rafał Miłecki 65a22d84ad kernel: backport bgmac changes from net-next
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-06-20 23:07:31 +02:00
Rafał Miłecki 4bd0edba1e kernel: rename bgmac patches that went into the same kernel
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-06-20 23:07:31 +02:00
Michael Lee 81913e4996 ramips: remove duplicate i2c dts info
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-20 11:45:44 +02:00
Michael Lee 60ccfbbad0 ramips: update i2c drivers
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
  so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
  it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
  it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
  not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
  names. and the hardware don't support error status. so i remove it.
  but the logic is the same.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-20 11:45:44 +02:00
Josh Bendavid 66ffd0ddf9 ipq806x: fix MAC_POWER_SEL switch configuration
Fixes instability/corruption on the ethernet interface connected to port0 on the switch.

Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
2016-06-20 11:45:44 +02:00
Mathias Kresin 153b3f05d4 lantiq: BTHOMEHUBV5A - use the power event code for the restart button
The restart event code is used in LEDE to trigger a factory reset on
long press as well.

By using the power event code, the restart functionality can be used
without being prone to trigger a factory reset.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-06-20 11:45:44 +02:00
Mathias Kresin 551c9c8300 lantiq: diag - switch off the power led on failsafe
This patch is a follow up to commit 4cf3fd4 "add support for indicating
the boot state using three leds".

At the time of writing the patch, I wasn't aware that it's possible to
switch info failsafe after boot (factory reset).

Enabling the failsafe led without disabling the running led causes an
unexpected led colour on devices using a single multicolour led to
indicate the boot state.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-06-20 11:45:44 +02:00
Mathias Kresin 32012decc3 lantiq: fix build of NAND sysupgrade images
The *_UBIFS_OPTS variables need to be prefixed with DEVICE_ to match
the profile name.

The conditions need to be evaluated after the *_UBIFS_OPTS are set,
otherwise the variables are always empty.

Do not append or pass the DEVICE_ prefixed profile name to the images.
Use the name that is passed by the Image/Build/Profile/ step.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-06-20 11:45:44 +02:00
Rafał Miłecki 776b24d9aa bcm53xx: properly support sysupgrade using Seama on NAND devices
It updates kernel and then formats UBI without loosing erase counters.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-06-20 08:02:32 +02:00
Rafał Miłecki cf6d9d97fb kernel: rename B53 symbols to avoid upstream kernel conflict
In kernel 4.7 there is upstreamed b53 driver using (mostly?) the same
symbols as our b53 does. Change our symbols so both drivers can coexist
in kernel tree.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-06-20 08:00:14 +02:00
Rafał Miłecki 1aca291214 kernel: mtdsplit: calculate kernel partition precisely for Seama
So far "kernel" partition didn't contain just a kernel. It also included
Seama header and meta data. This was making kernel update complex and it
wasn't trivial to read kernel size.
Fix it by making "kernel" parition contain just a kernel image.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-06-20 07:58:29 +02:00
Daniel Golle 67475b0e31 kernel: backport cosmetic ubifs patch
Despite the MS_SILENT flag being set when probing for ubifs rootfs a
logline indicating an error is generated during boot:
UBIFS error (pid: 1): cannot open "ubi0:rootfs", error -19
This leads to confusion and there shouldn't be lines containing
the word 'error' twice in a bootlog if actually everything is fine
(just the rootfs happens to be something else than ubifs)

The patch added has been submitted and was accepted upstream, see:
http://lists.infradead.org/pipermail/linux-mtd/2016-June/068056.html
http://patchwork.ozlabs.org/patch/637491

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-06-18 19:14:05 +02:00
Felix Fietkau 982108f7e5 lantiq: clean up / fix LegacyDevice template handling
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-17 20:23:11 +02:00
Felix Fietkau f4c59a204e lantiq: get rid of ifneq() checks inside command templates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-17 20:23:11 +02:00
John Crispin 9a0381f969 lantiq: small fix for legacy profile builds
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-17 20:11:24 +02:00
Jo-Philipp Wich ff4a804669 octeon: fix image build
The generic sysupgrade image attempted to use the wrong filesystem type due
to premature variable interpolation leading to the following error on the
buildbot system:

    cp: cannot stat `.../root.squashfs': No such file or directory
    make[4]: *** [.../tmp/lede-octeon-generic-ext4-sysupgrade.tar] Error 1

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-17 17:42:46 +02:00
John Crispin e81020c317 medaitek: convert the NAND target to UBI
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-17 04:13:08 +02:00
David Pinilla Caparrós bbbe9932e3 ar71xx: WDR4300: Fixed default VLAN order
Reordered the VLANs so the LAN ports are set to VLAN 1 and the WAN port is set to VLAN 2, as in the other routers in the config file. Moreover, this model had this VLAN mapping in OpenWRT Chaos Calmer. It seems that the VLAN were switched when fixing a bug in the port mapping ( OpenWRT changeset 47799 )

Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
2016-06-17 04:13:07 +02:00
John Crispin b180f24a3b Revert "ramips: update i2c drivers"
This reverts commit d8202a8409.

the commit broke I2C on various boards.

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-17 04:13:07 +02:00
Adrian Panella 0ddcbee261 ipq806x: activate ATAG DTB mangle and EA8500 rootblock in dts
The command-line arguments provided by the boot loader will be
appended to a new device tree property: bootloader-args.
If there is a property "append-rootblock" in DT under /chosen
and a root= option in bootloaders command line it will be parsed
and added to DT bootargs with the form: <append-rootblock>XX.
Only command line ATAG will be processed, the rest of the ATAGs
sent by bootloader will be ignored.
This is usefull in dual boot systems, to get the current root partition
without afecting the rest of the system.

Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-06-17 04:13:07 +02:00
Koen Vandeputte f532191c1c cns3xxx: fix RX softIRQ loop
Already reschedule when 1 or more frames came in.

Checking for a full queue could produce a re-schedule loop as
the checked RX ring location could contain undefined values
depending on activity in previous loops.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2016-06-17 04:13:07 +02:00
John Crispin 137b1ac5e8 netlogic: R.I.P
I asked florian and he is ok with this. i think no one apart from him has
access to these boards.

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-17 04:13:07 +02:00
John Crispin a6f7536a73 lantiq: convert remaining legacy targets to the new image generation code
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-17 04:13:07 +02:00
Alexander Couzens c2e0c41842 Revert "ar71xx/cpe510: use second wifi calibration table"
Using the high power table can damage the device in some cases.

This reverts commit bf27ac019c.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-06-16 21:11:24 -07:00
Felix Fietkau a285f1895b Revert "lantiq: Use correct macaddr generating logic for the DGN3500"
This reverts commit 492964e741, which
makes no sense. /etc/board.d cannot be used for system init stuff.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-15 18:40:48 +02:00
John Crispin 9fc250a481 realview: sync kernel config file
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-15 15:58:05 +02:00
Felix Fietkau 3a75777e86 lantiq: refresh patches
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-15 14:36:47 +02:00
Felix Fietkau ad76366d7d kernel: refresh patches
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-15 14:36:47 +02:00
Felix Fietkau be74158102 kernel: replace SMP cacheflush fix with some patches from linux-mti.git
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-15 14:36:47 +02:00
Felix Fietkau b3be33f135 bcm53xx: use uncompressed zImages
The boot loader expects LZMA compressed kernel images

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-15 14:36:47 +02:00
Felix Fietkau e6d3899ddc kernel: add support for uncompressed zImage on ARM
This can be used to prevent double compression for platforms where the
boot loader already expects compressed images.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-15 14:36:47 +02:00
Felix Fietkau af1791964d kernel: add common config symbols
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-15 14:36:47 +02:00
Felix Fietkau f27c70ff8c bcm53xx: refresh kernel config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-15 14:36:47 +02:00
Jo-Philipp Wich 14e2f4f6d1 ipq806x: add missing kernel config symbol
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-15 13:20:39 +02:00
Rujun Wang 1830c31632 mvebu: Configure status LED for WRT1900ACS
Signed-off-by: Rujun Wang <chinawrj@gmail.com>
2016-06-15 12:58:23 +02:00
John Crispin 24cd658a9d realview: bump to v4.4
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-15 11:49:02 +02:00
John Crispin f77a56d18a octeon: export the FILESYSTEMS variable during image generation
squashfs will be used for all images if this is not done

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-15 10:14:34 +02:00
John Crispin 7992633e63 octeon: Ignore MEM boot param when too small
Cisco RV0XX u-boot sets MEM=2048 as boot param. We assume that at least
4MB (mem_alloc_size) of ram is needed to run linux on cavium boards, so
if mem < 4M - ignore it and set default value

Signed-off-by: Michał Osowiecki <michal.osowiecki@gmail.com>
2016-06-14 13:30:11 +02:00
Josh Bendavid 9361285a41 ipq806x: restore old stmmac dma patch which is still needed to fix data corruption
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
2016-06-14 13:28:41 +02:00
Josh Bendavid e13b6322cd Revert "ipq806x: add mangle bootargs options in config-4.4"
This reverts commit 53147c2237.

These config changes break booting on C2600 and probably other devices.

Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
2016-06-14 13:28:41 +02:00
John Crispin e030c31e35 octeon: convert to new image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 13:00:30 +02:00
John Crispin bfcbca3e04 mediatek/ralink: fix boardnames
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 13:00:30 +02:00
Dirk Neukirchen 93276a351c omap: remove NAMESPACES config symbols
they are available in config/Config-kernel.in

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
2016-06-14 22:57:30 -07:00
Dirk Neukirchen 0dbd0b9ecd omap: remove XFRM config symbols
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
2016-06-14 22:57:30 -07:00
Dirk Neukirchen abf23d70ac omap: remove config symbol W1
it is available as module

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
2016-06-14 22:57:30 -07:00
Dirk Neukirchen 4ff529665f omap: remove config symbol NETFILTER
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
2016-06-14 22:57:30 -07:00
Dirk Neukirchen 21738fe01e omap: remove BMP085 symbol
BMP085 is a pressure sensor and available as module

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
2016-06-14 22:57:30 -07:00
John Crispin 9233db23f3 lantiq: the io space was still not big enough for UHCI
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 08:34:05 +02:00
John Crispin 88019c6c77 lantiq: add ARV4525PW wifi led
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 06:43:02 +02:00
John Crispin 90c48dd49d lantiq: fix VG3503J loader generation
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 06:43:02 +02:00
John Crispin d5666b98fa lantiq: fix fritz7320 wifi support
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 06:43:02 +02:00
John Crispin 98d00c35e3 lantiq: fix io_space_limit
this broke uhci pci support on some arv units

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 06:43:02 +02:00
Jo-Philipp Wich 5550d98015 ramips: fix kmod-sound-mt7620 packaging
Commit 9ff8928bb9 renamed the snd-soc-mt7620-i2s
driver and dropped snd-soc-mt7620-wm8960 which selected CONFIG_SND_SOC_WM8960
breaking all ramips builds due to undefined kernel config symbols.

Rework the kmod-sound-mt7620 package to explicitely select the
CONFIG_SND_SOC_WM8960 symbols and change it to bundle the renamed .ko file.

Also remove the @BROKEN flag and exclude it on the rt288x subtarget instead.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-14 14:31:18 +02:00
Rafał Miłecki 489efcfd62 bcm53xx: refresh kernel config
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
2016-06-14 12:19:38 +02:00
Felix Fietkau 7c02ecdd35 Revert "ar71xx: enable flow control for ethernet MACs with built-in switch"
This reverts commit 1beb5bec64.

It was found to cause the WAN port to fail on some AR934x devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-14 10:45:10 +02:00
John Crispin 9b4f17593a brcm47xx: add the small_Flash feature
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:44 +02:00
John Crispin 44e6c0f916 ath25: add the small_Flash feature
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:43 +02:00
John Crispin d57990e071 lantiq: fix ARV452CQW button gpio setup
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:43 +02:00
John Crispin d5143a49b7 lantiq: add AVM image mageic to sysupgrade script
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:43 +02:00
John Crispin 239ad94165 lantiq: add xway_legacy target
due to bloat recent builds fail to fit into the flash of the old danube units

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:43 +02:00
John Crispin 2ae06f3013 lantiq: gpio-export fails to build if GPIO_SYSFS is not enabled
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:43 +02:00
Arne Zachlod f869ffdd62 ar71xx: mach-ubnt-xm.c convert patches to mach file
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2016-06-13 22:51:43 +02:00
Henryk Heisig 01fb393c67 ramips/image: Add Archer C50 to mt7620 Makefile
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
Henryk Heisig 75af981239 ramips/base-files: Add support for Archer C50
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
Henryk Heisig 1c00c09eb6 ramips/dts: Add support for Archer C50
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
John Crispin bf007a480a lantiq: Add Support for Fritz!Box 7360 SL
Signed-off-by: Sebastian Ortwein <krone@animeland.de>
Tested-by: Guido Lipke <lipkegu@gmail.com>
2016-06-13 22:51:43 +02:00
Michael Lee 9a4935687d ramips: add support for DuZun DM06
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:43 +02:00
Michael Lee 49b7421836 ramips: enable wm8960 kernel menuconfig select option
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:43 +02:00
Michael Lee 6f61990d15 ramips: add i2s clocks
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:43 +02:00
Michael Lee 921d782eb7 ramips: update i2s dtsi files
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee 9ff8928bb9 ramips: improve i2s drivers
* remove mt7620-wm8960.c use simple card and DTS to do it
* add old chips support
* add 12Mhz refclk setup. this is hard code. need use clock framework
  rewrite it
* add interrupt error status support for debug. default disable it.
  because it cause to many interrupts
* add setup bclk suport not hard code it
* add 24 bits support for mt7628. not verified
* use regmap api to control registers
* add txdma-req/rxdma-req DTS params for DMA use

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee 42bbe28cf1 ramips: add i2c clock
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee 011ce1fad6 ramips: update i2c dtsi files
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee d8202a8409 ramips: update i2c drivers
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
  so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
  it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
  it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
  not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
  names. and the hardware don't support error status. so i remove it.
  but the logic is the same.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee f36d624d88 ramips: add gdma hsdma dts info
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
Michael Lee f6fc591561 ramips: enhance dma engine support
* fix compiler error. device_control operation not support now.
* add old chips support 8 channels. new chips support 16 channels.
* add mt7621 hsdma driver. data sheet says it has two channels.
  but after test only one channel support.
* add memory to memory DMA support. i use dmatest kernel module to
  verify this function. on rt305x it will copy more data. on mt7621
  only two channels can works at the same time. these two chips
  maybe have hardware bugs. because on other chips don't have these bugs.
* use tasklet to handle remaining dma requests.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:42 +02:00
John Crispin 8cc65914df ipq806x: move dts file to the files folder
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:42 +02:00
John Crispin 46cecfd6d7 ipg806x: set v4.4 as default
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:42 +02:00
Adrian Panella 53147c2237 ipq806x: add mangle bootargs options in config-4.4
Add config options to manage dual boot partitions, using MANGLE BOOTARGS

Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-06-13 22:51:42 +02:00
Adrian Panella 3d067c0132 ipq806x: base-files: add support for Linksys EA8500
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-06-13 22:51:42 +02:00
John Crispin 2adc6468bf ipq806x: build Linksys EA8500 images
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-06-13 22:51:42 +02:00
Adrian Panella bdaf558134 ipq806x: qcom rpm fix support for smb208
In commit "regulator: qcom: Rework to single platform device" the smb208
regulator used in IPQ8064 was left out.

Add it to that new framework and update Docs and DT accordingly.

Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-06-13 22:51:42 +02:00
John Crispin 928163bad2 uboot-envtools: add ipq806x support
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-06-13 22:51:41 +02:00