Commit Graph

1294 Commits (20b069c440c1061bda64808018be9254cea7f220)

Author SHA1 Message Date
Felix Fietkau 2067f7f1de ar71xx: use page fragment API in the ethernet driver
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48578
2016-01-31 12:29:34 +00:00
Felix Fietkau 2530640f07 ar71xx: add support for linux 4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48563
2016-01-30 13:19:53 +00:00
Felix Fietkau e5b5cce442 ar71xx: fix a few include errors
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48562
2016-01-30 13:19:37 +00:00
John Crispin 9d4e076966 ar71xx: fix AR8337 switch initialization on dLAN pro 1200+ WiFi ac
unswap ports 0/6 (broken by 17b8dcd63100a6b9e35199882f38bdc2be640777)

Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 48357
2016-01-19 10:16:11 +00:00
John Crispin ed72c5f846 ar71xx: add support for Netgear WPN824N
Add support for Netgear WPN824N.
Hardware specs:
  * AR7240, 4 LAN ports, 1 WAN port
  * AR9285 WLAN
  * 32 MB RAM
  * 4 MB Flash
  * 16 LEDs (LAN, WAN and Power/Status contain two LEDs for dual color
    effect)
  * 3 Buttons (not supported)

Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>

SVN-Revision: 48356
2016-01-19 10:16:04 +00:00
Felix Fietkau 5c5c60fec4 ar71xx: fix ethernet MAC reset on DMA hang
Fully reset the chip like on a full up/down, but without the PHY
statemachine restart.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48228
2016-01-13 16:22:16 +00:00
Felix Fietkau cf2cf43717 ar71xx: extend ethernet DMA stuck check to all ar724x (and newer) chips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48227
2016-01-13 16:22:05 +00:00
Felix Fietkau 826cfa5773 ar71xx: fix ap152 support
- ethernet gigabit pll
- switch configuration
- sysupgrade

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 48187
2016-01-10 17:19:34 +00:00
John Crispin 9242d27b4a V2 ar71xx : Add Support for the Bitmain Antrouter R1
This patch adds support for the Bitmain Antrouter R1

http://wiki.openwrt.org/toh/bitmain/r1

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 48058
2016-01-01 21:21:13 +00:00
John Crispin 772f9d4e32 ar71xx: Add support for AirTight Networks C-55
This patch is to add support for the AirTight Networks C-55 Access Point

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47973
2015-12-23 14:43:35 +00:00
Felix Fietkau 814d70b2fd ar8216: rework/fix AR8337 MAC swap handling
In r45970 the MAC swap handling was made opt-in, however some boards
have been forgotten during the conversion. Since the reference design
uses this MAC swapping, and pretty much all known boards using this chip
seem to do so too, enabling the swapping is a more reasonable default
than leaving it disabled.

Change the code to still allow boards to opt-out of this.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47956
2015-12-20 14:25:45 +00:00
Felix Fietkau 3fa85af5ad ar71xx: Add ath79_register_m25p80_large to support >16MB SPI chips
The following patch is to add ath79_register_m25p80_large, which sets
is_flash to false to support bit banging. This is needed on some 32MB+
SPI chips, such as the S25FL256S1

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47952
2015-12-19 11:32:20 +00:00
Felix Fietkau 3f184882e8 ar71xx: Kernel board definition for PowerCloud CR5000
Kernel part of support for the PowerCloud Systems CR5000.  The
    CR5000 is a dual-band 802.11n wireless router with 8MB flash,
    64 MB RAM, (unused in stock firmware) USB 2.0 port, and five
    port gigabit ethernet switch.  The CR5000 was sold as hardware for
    the Skydog cloud-managed router service.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47940
2015-12-19 11:27:32 +00:00
Felix Fietkau eef3b7acfb ar71xx: Kernel board definition for PowerCloud CR3000
Kernel part of support for PowerCloud CR3000.  The CR3000 is
    a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM,
    a four port fast ethernet switch, and a fast ethernet wan port which
    was sold by PowerCloud Systems as hardware for the Skydog
    cloud-managed router service.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47939
2015-12-19 11:27:25 +00:00
Felix Fietkau 4cc541756d ar71xx: Kernel board definition for PowerCloud CAP324
Kernel part of support for PowerCloud CAP324 Cloud AP.
    The CAP324 Cloud AP was a device sold by PowerCloud Systems as hardware for
    the CloudCommand service for 'cloud' based managment of large numbers
    access points.

    The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
    and 128MB RAM and single gigabit ethernet port.  It can be powered via PoE
    or a power adaptor.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47938
2015-12-19 11:27:19 +00:00
John Crispin 1f71f2220d ar71xx: add support for TRENDnet TEW-823DRU
Add support for TRENDnet TEW-823DRU:
- cpu: QCA9558 @720MHz
- flash: 16MB
- ram: 256MB
- 4+1 RJ45 100/1000Mbps
- wifi:  QCA9558 (bgn) and QCA9880-BR4A (ac)
- 1x USB 2.0

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 47927
2015-12-17 09:30:05 +00:00
Felix Fietkau 6505dc3367 ar71xx: clean up ethernet tx queue after reset, wake queues when done - fixes hangs reported in #18922
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47892
2015-12-14 20:22:09 +00:00
John Crispin abc84551c0 ar71xx: add support for Cisco's MR18
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47878
2015-12-12 06:42:29 +00:00
Felix Fietkau 0b6271faf4 ar71xx: reorganize target patches/files to make it possible to add boards without adding patch files
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47874
2015-12-11 21:12:14 +00:00
Felix Fietkau 0186d4c2c2 ar71xx: on wnr2200, revert the mac0/mac1, the ethernet interfaces are swapped. use MAC1 for wlan
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47873
2015-12-11 21:12:04 +00:00
Felix Fietkau 6e12ef7430 ar71xx: fix MAC address swapping on WNR2200 and fix the WLAN MAC address
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47871
2015-12-11 19:21:59 +00:00
John Crispin 1dada3fc3c ar71xx: add LED driver NU801
The MR18 uses a 3-channel 16-bit PWM Constant Current Driver
for its status LED.

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47848
2015-12-11 15:04:57 +00:00
John Crispin eb8ff56684 ar71xx: Add support for Wallys DR344
This patch is for Wallys DR344 support under OpenWRT

Signed-off-by: Philippe Duchein <wireless-dev@duchein.net>

SVN-Revision: 47847
2015-12-11 15:04:47 +00:00
John Crispin 1a092ce0e0 ar71xx: add GL-Domino Pi support V3
This is the patch for GL-Domino Pi V3. Updated against the latest trunk.

Signed-off-by: alzhao<alzhao@gmail.com>

SVN-Revision: 47622
2015-11-24 18:30:50 +00:00
John Crispin a04c3e73a3 ar71xx: add GL-AR300 support V3
This is the patch for GL-AR300 V3, tested against the latest trunk.

Signed-off-by: alzhao<alzhao@gmail.com>

SVN-Revision: 47621
2015-11-24 18:30:19 +00:00
John Crispin 72093bd528 ar71xx: add GL-AR150 support V3
This is the 3rd version. Modified against the latest trunk.

Signed-off-by: alzhao<alzhao@gmail.com>

SVN-Revision: 47620
2015-11-24 18:29:59 +00:00
John Crispin 99fd9a7041 ar71xx: add support for the devolo dLAN Hotspot
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 47554
2015-11-21 21:24:18 +00:00
Hauke Mehrtens fa137d51f5 ar71xx: add Arduino Yun
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
7e2976fa83

The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.

Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47451
2015-11-10 23:13:09 +00:00
Felix Fietkau 7f75961e38 ar71xx: add support for TP-LINK TL-WR941ND v6 (international version)
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.

This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 47420
2015-11-08 20:39:18 +00:00
Felix Fietkau ae7e7239b8 ar71xx: Add support for ZyXEL NBG6616.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>

SVN-Revision: 47405
2015-11-07 12:51:39 +00:00
John Crispin 632c92094a ar71xx: Bitmain Antminer S1/S3 set GPIO for USB Power
Antminers using the stock bootloader will not hash without this GPIO set.
Applies to DD and CC

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 47261
2015-10-26 09:01:28 +00:00
John Crispin fb152a810c ar71xx: Send power to USB port on WNR2200
This patch fixes ticket #15267 by enabling power on the
WNR2200's USB port. At present, the USB port on the WNR2200
is non-functional due to it not receiving power.

This patch defines an additional GPIO pin, but none of the
current GPIO definitions have been modified.

Signed-off-by: Riley Baird <BM-2cVqnDuYbAU5do2DfJTrN7ZbAJ246S4XiX@bitmessage.ch>

SVN-Revision: 47236
2015-10-19 18:18:12 +00:00
John Crispin 8d8a937272 ar71xx: Add Gainstrong MiniBox v1.0 support to trunk
This patch supersedes the v1 from September 17th.

Bumping the patch version - the MiniBox profile showed up under M, but
since it's called 'Gainstrong MiniBox v1.0' now it looks out of place.
Renamed the profile to gs-minibox-v1.mk to fix that.

The following patch adds support for the Gainstrong MiniBox into trunk
(or 'Designated Driver' :D ).

Fixed items:

- Inverted LED polarity (OOLITE seems to suffer from the same problem).
- Changed uppercase MINIBOX_V1_ prefix as requested.
- Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor).
- Mention the vendor (Gainstrong) in code headers.

Compiles fine, has been confirmed working by owners on 15.05.

Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c,
the MiniBox images build fine without, so I'm wondering: do I need to add
it in there as well? Any added benefit?

Thank you

Signed-off by: Stijn Segers <francesco.borromini@inventati.org>

SVN-Revision: 47234
2015-10-19 17:55:25 +00:00
John Crispin 257e76a3df ar71xx: Bitmain Antminer S1 & S3 cleanup
Sets the LEDs to boardname:color:led-name
Sets the LAN to eth0
Other corrections such as the Machine Name and HWIDs
v2 corrects the profile names in the Makefile and changes tabs to spaces
in the Makefile 'define Device/' like the other devices.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 47221
2015-10-19 10:10:02 +00:00
Felix Fietkau 896d3e3e13 ar71xx: Add WeIO Board Support
Add support for WeIO board (http://we-io.net).
This board is based on Carambola2 board form 8Devices.

Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org> [some cleanups]

SVN-Revision: 47036
2015-09-24 09:08:47 +00:00
John Crispin ac75fc8d98 ar71xx: add support for ap152 reference board
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46972
2015-09-16 08:33:14 +00:00
John Crispin f6607a4bec ath79: dev-eth: fix QCA9561 set phy interface mode and mask
QCA9563 and QCA9561 are two series of Qualcomm SoC Dragonfly. The only different
is QCA9563 w/o internal switch. It has one GMAC with SGMII interface. But they
have the same device ID(0x1150). So they share the same codes.

Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46971
2015-09-16 08:33:04 +00:00
John Crispin 0dbced8a48 ar71xx: add TP-LINK TL-WDR3320 v2 support
This patch adds support for TP-LINK TL-WDR3320 v2.

This router uses a chinese version 2 firmware header,.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 46934
2015-09-14 20:12:16 +00:00
John Crispin aba20334a4 ar71xx: add kernel support for the OpenMesh MR1750 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46926
2015-09-14 20:10:43 +00:00
Felix Fietkau 2ce833060a target: ar71xx: add support for COMFAST CF-E316N v2 board
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 46852
2015-09-11 16:31:35 +00:00
John Crispin af60c367b7 ar71xx: add support for TP-Link TL-WDR6500 v2
Signed-off-by: Weijie Gao <hackpascal@gmail.com>

This patch adds support for TP-Link TL-WDR6500 v2.

The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.

SVN-Revision: 46663
2015-08-17 06:24:04 +00:00
John Crispin a2b38ebf77 ar71xx: add 64kb bootloader mtd parser for tplinkpart
Signed-off-by: Weijie Gao <hackpascal@gmail.com>

This patch adds flash layout parser for TP-Link firmwares which have a 64kb
bootloader.

This is used for TP-Link TL-WDR6500 v2.

SVN-Revision: 46662
2015-08-17 06:23:49 +00:00
John Crispin 4463bc017b ar71xx: Add support for Black Swift
Add support for the Black Swift board:
http://www.black-swift.com/

Took relevant parts and slightly adapted from:
https://github.com/blackswift/openwrt/blob/master/bsb.patch

Signed-off-by: Bruno Randolf <br1@einfach.org>

SVN-Revision: 46651
2015-08-17 06:16:54 +00:00
John Crispin 5cd49bb067 ar71xx: add support for Onion Omega
This patch adds support for the Onion Omega.

https://onion.io/omega

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Boken Lin <bl@onion.io>
Tested-by: Jacky Huang <huangfangcheng@163.com>

SVN-Revision: 46458
2015-07-24 09:09:49 +00:00
John Crispin b98205c946 ar71xx: Add support for AP147-010 reference board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46457
2015-07-24 09:09:42 +00:00
Felix Fietkau 38dbf49b61 ar71xx: remove the use of the obsolete IRQF_DISABLED flag in the NAND flash driver (fixes #20125)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46433
2015-07-20 06:01:18 +00:00
Felix Fietkau d26e8d9439 Revert "ar71xx: Add support for Cisco-Linksys WAP4410N" (r46250)
The commit is incomplete, it does not even build the mach-* file

This reverts commit 6e6adcf7a197b1802cb728ddcccf05f890ca0574

SVN-Revision: 46425
2015-07-19 17:58:27 +00:00
John Crispin 1eccdb4fd4 ar71xx: add support for the devolo dLAN pro 1200+ WiFi ac
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 46342
2015-07-14 07:37:03 +00:00
John Crispin 02984a6e09 ar71xx: add support for the devolo dLAN pro 500 Wireless+
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 46338
2015-07-14 07:32:33 +00:00
John Crispin e8161f4764 ar71xx: compex wpe72 add space to include statement
Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46284
2015-07-09 07:04:14 +00:00
John Crispin 8a1cca04ca ar71xx: compex wpj531 register usb support
Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46283
2015-07-09 07:03:54 +00:00
John Crispin 3802ce01a9 ar71xx: compex wpj531 fix setting mac address on ethernet
Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46282
2015-07-09 07:01:55 +00:00
John Crispin 4b28adc066 ar71xx: compex wpj531 fix ethernet registration
In fb6f62e97733312053ab593fcf68eea47a21169e several settings
are set on the ethernet device, but they are not working.

Fix Ethernet by setting the right values.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46281
2015-07-09 06:59:18 +00:00
John Crispin 3b14473968 ar71xx: ag71xx remove IRQF_DISABLED
no-op since 2.6.35
removed in Kernel 4.1
see https://lwn.net/Articles/380931/

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>

SVN-Revision: 46280
2015-07-09 06:57:39 +00:00
John Crispin 08790c5ee8 ar71xx: Add support for Cisco-Linksys WAP4410N
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.

Signed-off-by: Ryan A Young <rayoung@utexas.edu>

SVN-Revision: 46250
2015-07-07 18:06:39 +00:00
John Crispin d535218230 ar71xx: add support for D-Link DIR-615 rev. Ix board
Based on trunk r46212.

Signed-off-by: Jaehoon You <teslamint@gmail.com>

SVN-Revision: 46248
2015-07-07 13:48:39 +00:00
John Crispin f7ffbbc5fc ar71xx: Use *_eth_cfg helper for Open Mesh MR900 boards
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46241
2015-07-07 13:47:39 +00:00
John Crispin 055663201b ar71xx: Add Support for the Bitmain Antminer S3
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner

http://wiki.openwrt.org/toh/bitmain/s3

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46236
2015-07-07 13:46:54 +00:00
John Crispin 9f2b8b3902 ar71xx: allow pci calibration fixup to work with ar9344
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 46235
2015-07-07 13:46:44 +00:00
Felix Fietkau b26077026f ar71xx: add support for ap143
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46208
2015-07-07 08:06:05 +00:00
Felix Fietkau c9e433206f ar71xx: rework patch for qca953x/956x
Patch cherry-picked from the following location:
https://www.codeaurora.org/cgit/quic/qsdk/oss/system/openwrt/commit/?h=release/coconut_ioe4531_2.0&id=5c357bf6c763e4140dddcc9a3bc5f005525a9c0e

Changelist,
    - add more register defines
    - add EHCI support
    - fix GPIO pin count to 18
    - fix chained irq disabled
    - fix GMAC0/GMAC1 initial
    - fix WMAC irq number to 47
    - merge the changes of dev-eth.c from the patch to file.

Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 46207
2015-07-07 08:05:55 +00:00
Felix Fietkau 7acbd52055 ar71xx: fix ethernet initialization on QCA953x-based boards (TP-Link TL-WR841N/ND v9, Compex WPJ531)
The initialization routines for these boards were relying on some (wrong)
defaults for the QCA953x ethernet. Make these defaults explicit to prevent
breaking them when the QCA953x defaults are fixed.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 46206
2015-07-07 08:05:50 +00:00
John Crispin be755a99d6 ar71xx: add kernel support for EnGenius EPG5000.
Signed-off-by: Christian Beier <cb@shoutrlabs.com>

SVN-Revision: 46047
2015-06-18 18:21:33 +00:00
John Crispin e85f3471ba ar71xx: add support for TL-WR720N-v4.
The hardware should be almost the same as TL-WR720N-v3.  WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>".  Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 46046
2015-06-18 18:21:23 +00:00
John Crispin 8399be545a ar71xx: add support for compex wpj531
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj531-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46045
2015-06-18 18:21:15 +00:00
John Crispin 694dd581eb ar71xx: Add Support for the Bitmain Antminer S1
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner

http://wiki.openwrt.org/toh/bitmain/s1

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>

SVN-Revision: 46044
2015-06-18 18:21:05 +00:00
Felix Fietkau a5cd02aec4 ar71xx: ar934x-nfc: allow ECC to be configured in software BCH mode
Some devices ship with NAND images that use BCH ECC. Let the driver know
about that ECC mode so that it can be selected by machine files.

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>

SVN-Revision: 46022
2015-06-18 06:37:01 +00:00
Felix Fietkau a1b8ee0307 ar71xx: return limit as number of processed frames when re-scheduling NAPI poll
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45971
2015-06-14 17:43:59 +00:00
Felix Fietkau 4a9d726200 ar8216: Fix problem with AR8337 MAC swap handling
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.

Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.

The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 45970
2015-06-14 17:43:50 +00:00
Felix Fietkau 28d8972c25 ar71xx: fix 100/10mbps ethernet link issues on mynet range extender
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.

The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.

The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.

Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 45954
2015-06-14 17:41:01 +00:00
John Crispin 66950455b7 ar71xx: Add support for the Meraki MR12 & MR16
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.

Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>

SVN-Revision: 45726
2015-05-23 15:27:22 +00:00
Luka Perkov 2a9ebfb503 ar71xx: add status led found on ew-dorin boards
Signed-off-by: Catrinel Catrinescu <cc@80211.de>

SVN-Revision: 45656
2015-05-10 07:47:04 +00:00
Felix Fietkau 11c588bc96 ar71xx: do general formatting on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45640
2015-05-08 12:24:30 +00:00
Felix Fietkau d4600d867c ar71xx: fix spelling, add copyright on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45639
2015-05-08 12:24:23 +00:00
Felix Fietkau b1aea59f08 ar71xx: add support for Green WAN LED on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45638
2015-05-08 12:24:17 +00:00
Felix Fietkau aa970f13a3 ar71xx: add support for green LAN LEDS for wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45637
2015-05-08 12:24:11 +00:00
Felix Fietkau 17c78d12bd ar71xx: fix amber WAN LED setting for wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45636
2015-05-08 12:24:03 +00:00
Felix Fietkau 5e1e04e505 ar71xx: make WLAN button RFKILL on wnr2000-v4
Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45635
2015-05-08 12:23:58 +00:00
Felix Fietkau b1380ebae3 ar71xx: set all buttons to be active_low on wnr2000-v4
Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45634
2015-05-08 12:23:53 +00:00
Felix Fietkau 6413f40e96 ar71xx: fix ethernet on wnr2000-v4
Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861

I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
  1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
  2) must init GMAC0 before GMAC1

That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.

An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.

2) Possible consequence of no longer explicitly setting ethernet duplex/speed.

Review: With this patch, my ethernet and wireless works.

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45633
2015-05-08 12:23:45 +00:00
Felix Fietkau a51f5cace4 ar71xx: use a common naming scheme for LEDS on wnr2000-v4
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45630
2015-05-08 12:23:27 +00:00
Luka Perkov 8084b056e2 ar71xx: fix leds and gpio on wpj344
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45589
2015-04-29 20:04:46 +00:00
Luka Perkov 9d76de9771 ar71xx: add support for compex wpj344
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45527
2015-04-20 20:47:48 +00:00
Felix Fietkau 0a4b20166d ar71xx: Increase RXD/RDV to 2 on OM5P-AN
It was reported that OM5P-AN needs not only a delay setting of 1 for RXD/RDV
but 2. These was found when testing with a NetGear GS752TP POE switch with a
cable length of 50ft and 250ft.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 45524
2015-04-20 15:01:00 +00:00
Felix Fietkau f4e6418a32 ar71xx: add a helper function to set RXDV/RXD of ETH_CFG on AR934x
The ETH_RXDV_DELAY (17:16) and ETH_RXD_DELAY (15:14) are currently not cleared
by the function ath79_setup_ar934x_eth_cfg. Clearing these in the
ath79_setup_ar934x_eth_cfg may cause problems on some hardware because they
rely on the preset value by the bootloader.

Instead another function is introduced which also works on ETH_CFG on AR934x.
It can be used to safely clear and set ETH_RXDV_DELAY and ETH_RXD_DELAY on
machines which require special settings.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 45523
2015-04-20 15:00:52 +00:00
Felix Fietkau 5c6925a23b ar71xx: Remove TX/RX delay from pll_1000 for OM5P-AN
The tx/rx delay bits in the ETH_XMII_CONTROL register have to be unset when the
enable_rgmii_rx_delay/enable_rgmii_tx_delay will be set in the AT803x PHY.
Othwise the throughput in gigabit mode is heavily reduced.

Signed-off-by: Sven Eckelmann <sven@open-mesh.org>

SVN-Revision: 45521
2015-04-20 15:00:20 +00:00
John Crispin efbdc168ff ar71xx: fix ethernet packet loss issues on OM5P-AN
The OM5P-AN boards are suffering from ethernet packet loss when booting with
some active POE setups or when switching to Fast Ethernet when previously
booted with Gigabit ethernet attached.

The cause of the problem is that the AR8035 PHYs requires special register
settings to work reliably on these boards. Enable the RGMII TX, RX delays and
disable SmartEE functionality of the AR8035 PHYs. Also enable the RXD and RDV
delay in the ETH_CFG register to fix the issue.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 45438
2015-04-14 19:00:51 +00:00
Gabor Juhos d0a6b278db ar71xx: add initial support for RB911G-5HPacD
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 45299
2015-04-07 20:04:03 +00:00
Gabor Juhos 96b006eb32 ar71xx: routerboot: export extended wlan data via sysfs
Export the data to make it accessible from user-space.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 45298
2015-04-07 20:03:43 +00:00
Gabor Juhos 76b5a9aa7d ar71xx: routerboot: add support for extended radio data
On newer Mikrotik boards, the radio calibration data
is stored differently and uses LZO compression instead
of RLE.

Update the RouterBOOT helper code to support the new
format.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 45297
2015-04-07 20:03:35 +00:00
John Crispin 17a1e18ee2 ar71xx: add kernel support for the OpenMesh OM5P-AN board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 44861
2015-03-17 09:43:19 +00:00
John Crispin 7ea781558f ar71xx: fix TP-LINK TL-WDR3600/4300 RFKILL switch positions
While the switch positions aren't explicitly labeled as on and off, we've heard
complaints about them being wrong. This patch changes the handling to match the
stock firmware.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 44795
2015-03-15 19:39:47 +00:00
John Crispin 5ca2ad1063 Fix (invert/revert) Hornet-UB WPS LED state
My previous patch regarding the Hornet-UB board
(commit: beed4d82d6a0154b0cd5f7b84e2180215ace6718) actually
causes the WPS led state to be inverted. Practically this meant
that value 0 in /sys/class/led/alfa:blue:wps/brightness would
turn the LED on and any positive value (1-255) would turn it off.

The above of course is confusing and hence reverting this value
back to the way it was before beed4d82d6a0154b0cd5f7b84e2180215ace6718.

Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>

SVN-Revision: 44791
2015-03-15 19:25:48 +00:00
John Crispin 3a1a4165b8 ar71xx: Ext LNA patch for TUBE2H and HORNET-UB targets
Signed-off-by: Christophe Prévotaux <c.prevotaux@rural-networks.com>

SVN-Revision: 44693
2015-03-12 10:06:53 +00:00
John Crispin fd82ffec00 ar71xx: Hornet UB GPIO WPS/Reset
This problem has existed at least since Attitude Adjustment and
is also present in trunk. Basically on the Hornet-UB board the
functionality of RESET and WPS have "switched places".

There are two tickets about the issue at dev.openwrt.org,
The solution suggested on them both is incomplete though
and introduces the following proglem:

Patching as suggested on #14136/#15282 will result in a situation
where simply pressing the RESET button on the bottom will cause
FACTORY RESET to be run. This is due to GPIO high/low state being
incorrect as a result of the above change and virtually the RESET
button is in the pressed-down state the entire time. When it is
then physically pressed, that causes the opposite, release, to be
triggered and since to the board it seemed that the button was
pressed long before it was released, the FACTORY RESET results.

The attached patch works as expected. I have verified both the
incorrect functionality as well as after fixing the issue as
described in the patch and flashing the resulting firmware to a
Hornet-UB board.

Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>

SVN-Revision: 44692
2015-03-12 10:06:42 +00:00
John Crispin a0c4419b0d ar71xx: improve WD's My Net Wi-fi Range Extender image creation
Previously, the generated images for the My Net Wi-fi Range Extender
wouldn't always work (and panic) due to the fixed mtd offsets and
sizes for the kernel and rootfs. This patch fixes the problem by
utilizing the shared Cybertan's partition parser to recalculate
the mtd partitions for every image dynamically everytime.

Reported-by: Pascal Paradis <peparadis@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 44665
2015-03-11 15:56:34 +00:00
John Crispin 69955cf733 ar71xx: generalize cybertan partition parser
By removing the NL16 signature check, the parser can be
utilized by other devices like the WD My Net Wi-fi Range
Extender.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 44664
2015-03-11 15:56:27 +00:00
John Crispin e5373f2761 ar71xx: rename wrt160nl's trx partition parser
This patch renames the partition parser from
wrt160nl to more generic cybertan.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 44663
2015-03-11 15:56:15 +00:00
John Crispin daf2140192 ar71xx: fix gpio-latch driver
gpio api has changed. the remove call no longer returns a value.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44650
2015-03-10 20:19:54 +00:00
Luka Perkov e04e623009 ar71xx: wpj588: add missing usb support
Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-By: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 44648
2015-03-10 16:11:39 +00:00