At offset 0x40, signature for TL-MR10U/TL-MR11U begin
from 0x00, not 0x10/0x11.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36727 3c298f89-4303-0410-b956-a3cf2f4a3e73
MR10U is closer to MR3040 than WR703N. This changes also
enable USB power on GPIO18.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36726 3c298f89-4303-0410-b956-a3cf2f4a3e73
This allow us to increase the kernel partition size,
and ensures, that the -factory image still usable via
the original interface.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36584 3c298f89-4303-0410-b956-a3cf2f4a3e73
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36580 3c298f89-4303-0410-b956-a3cf2f4a3e73
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36579 3c298f89-4303-0410-b956-a3cf2f4a3e73
Here is corrected version (only thing not working are wifi LEDs).
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36578 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update the numbering of kernel patch for supporting
Netgear WNR2000v3 from 617 to 618.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36498 3c298f89-4303-0410-b956-a3cf2f4a3e73
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36459 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for TPLINK WR720N v3 which has 4MB flash,
32MB ram, 2 ethernet interfaces, 1 USB 2.0 port.
The patch is mostly a modification from mach-tl-wr703n.c.
GPIO numbers for the slider switch is from mach-tl-mr3020n.c.
Tested on my device and they worked fine.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36456 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also refresh the related generic/platform patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36039 3c298f89-4303-0410-b956-a3cf2f4a3e73
[juhosg: use different profile name for v1 and v2, and add
multi profile to build for both versions]
Signed-off-by: Guilhem Lettron <guilhem@lettron.fr>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36038 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use eeprom (art) from included wifi card, not hard coded in flash.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36037 3c298f89-4303-0410-b956-a3cf2f4a3e73
Error in using another MDIO (AP123 platform using only one GE1 device
for eth0 and eth1) for the router mr3420v2.
?onfirmed: https://forum.openwrt.org/viewtopic.php?pid=194779#p194779
Routers in this sense are the same and the only difference is: USB
port, USB led, instead of the GPIO-switch we have GPIO-button.
Signed-off-by: Dmytro <dioptimizer@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36036 3c298f89-4303-0410-b956-a3cf2f4a3e73
[juhosg: use gpio_request_one to enable the USB power]
Patch-by: Dmytro <dioptimizer@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@opewrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35961 3c298f89-4303-0410-b956-a3cf2f4a3e73
LAN1 and LAN2 LEDs not present (it pulled to ground via
resistors) on MR3040 and MR11U devices. This little patch
enabling ability to control GPIO14 and GPIO15.
Patch-by: Dmytro <dioptimizer@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3439/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35960 3c298f89-4303-0410-b956-a3cf2f4a3e73
[juhosg:
- remove custom mdio bus info and platform data for ar8327, clear the
.led_cfg field from dir835a1_setup instead,
- remove arguments of dir835c1_generic_setup function, register the
LEDs directly from the board specific setup instead]
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Patchwork: http://patchwork.openwrt.org/patch/3426/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35957 3c298f89-4303-0410-b956-a3cf2f4a3e73
Added support for the TP-LINK TL-WA830RE v1 Range Extender.
Based on the WA901ND v1 support. Hardware IDs checked against
original firmware. Patch was successfully tested on hardware.
Signed-off-by: Ronald Hecht <ronald.hecht@gmx.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35789 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the same MAC addresses as the original firmware.
Based on a patch from #10421.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Tested-by: Gabor Varga <vargagab@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35730 3c298f89-4303-0410-b956-a3cf2f4a3e73
Makes warnings/errors visible when building with V=w/V=1.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35719 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is platform definition for the RB951G device. It's mostly rework
of RB2011UAS patchset with network taken from the RB751 patches.
The main difference is the flash layout used by this device.
[juhosg:
- remove dead code from mach-rb951g
- add "-2HnD" suffix to the machine name
- use a separate 615-MIPS-ath79-RB951G-support.patch]
Patchwork: http://patchwork.openwrt.org/patch/3257/
Signed-off-by: Kamil Trzcinski <ayufan@ayufan.eu>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35633 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thanks to Jonas Gorski for the help.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35567 3c298f89-4303-0410-b956-a3cf2f4a3e73
Accessing the AR8xxx switches via the name of the
attached ethernet device is not possible since
r35560. Change the uci-defaults script to use
switchX names in switch configurations.
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35561 3c298f89-4303-0410-b956-a3cf2f4a3e73
We utilize many Routerboard 751's and discovered that our latest batch
of RB751's would not initialize the wireless radio. We have determined
Mikrotik has changed where the mac address was located inside hardconfig.
As such we utilize "routerboot_find_tag" to find the location of the mac
address. We should remove "RB751_MAC_ADDRESS_OFFSET" as it is ambiguous
by machine manufacturing date. The newer batch of RB751's that we received
had a RB751_MAC_ADDRESS_OFFSET 0x10.
Signed-off-by: Davey Hutchison <dhutchison@bluemesh.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35519 3c298f89-4303-0410-b956-a3cf2f4a3e73
Gabor Juhos
Felix Fietkau
Jonas Gorski
Steven Barth
John Crispin
Luka Perkov