Instead of using xargs to pass a huge number of files to
script/ipkg-remove, which will usually pick only one, use a more
restrictive wildcard so that, currently, at the most 325 files are
examined, instead of up to over 2,300. The 325-file package is python,
which is picking up python3* ipks. It is about to be removed.
Runner-up is ddns-scripts with 7 files.
This makes a second run of make package/luci/compile go from
real 16.40s; user 17.42s; sys 2.73s
to
real 10.71s; user 9.51s; sys 1.27s
There is a caveat though: if one were to remove the ABI_VERSION of a
package that ends in a digit [0-9], then the old package ipk will not be
removed from the bin directory by make package/abc2/clean.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The wildcard call to clean up luci package (luci*) can pick up over
2,300 files when the full tree is built. Running make package/luci/clean
or a second run of make package/luci/compile would fail with an
'Argument list too long' error.
To avoid that, a maybe_use_xargs function was created that runs the
command straight as usual if the number of arguments is < 512, or saves
the list in a temporary file and feeds it to xargs otherwise.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Instead of calling $(wildcard) to check if the removal list is empty,
then calling it again to actually remove the files, define a function so
that the arguments are expanded only once when it gets called.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Fixes following warnings:
In target/toolchain/files/wrapper.sh line 18:
REALNAME=$(readlink -f $0)
^-- SC2086: Double quote to prevent globbing and word splitting.
--
In target/toolchain/files/wrapper.sh line 20:
REALNAME_BASE=$(basename $REALNAME)
^-------^ SC2086: Double quote to prevent globbing and word splitting.
--
In target/toolchain/files/wrapper.sh line 21:
REALNAME_DIR=$(dirname $REALNAME)
^-------^ SC2086: Double quote to prevent globbing and word splitting.
--
In target/toolchain/files/wrapper.sh line 74:
exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin $GCC_SYSROOT_FLAGS $TARGET_FUNDAMENTAL_CFLAGS $TARGET_ROOTFS_CFLAGS "$@"
^-----------------------^ SC2086: Double quote to prevent globbing and word splitting.
--
In target/toolchain/files/wrapper.sh line 77:
exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin $LD_SYSROOT_FLAGS $TARGET_FUNDAMENTAL_LDFLAGS "$@"
^-----------------------^ SC2086: Double quote to prevent globbing and word splitting.
--
In target/toolchain/files/wrapper.sh line 80:
exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin $TARGET_FUNDAMENTAL_ASFLAGS "$@"
^-----------------------^ SC2086: Double quote to prevent globbing and word splitting.
--
In target/toolchain/files/wrapper.sh line 83:
exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin "$@"
^-----------------------^ SC2086: Double quote to prevent globbing and word splitting.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Zram is only strictly dependent on lzo, not lz4. Break this dependency and
make the lz4 module visible in the configuration, in order for the user to
have the choice of enabling/disabling it, if (s)he sees fit.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The block-mount swapon implementation doesn't support discard, so make zram-swap
depend only on the default BusyBox implementation or, when unavailable, on the
one present in the swap-utils package.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The clock_gettime(CLOCK_MONOTONIC) syscall exists for so long that the first
kernel version to support it is not even specified in the man page [1]. Let's
enable it on BusyBox by default. Otherwise, gettimeofday will be used instead,
which will give wrong results if the date/time is reset (time moving backwards).
[1] https://linux.die.net/man/2/clock_gettime
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
CMake is less error prone that autotools and also compiles faster.
Fixed license information.
Added pkgconfig file to InstallDev so that packages that use it can
find lzo.
Before:
time make package/lzo/compile -j 12
________________________________________________________
Executed in 20.87 secs fish external
usr time 26.95 secs 0.00 micros 26.95 secs
sys time 5.49 secs 305.00 micros 5.49 secs
After:
time make package/lzo/compile -j 12
________________________________________________________
Executed in 13.22 secs fish external
usr time 19.59 secs 328.00 micros 19.59 secs
sys time 4.03 secs 10.00 micros 4.03 secs
Time output is with fish shell. make clean was ran before both attempts.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
f4e9bf73ac5c examples/lua: attempt to highlight some traps
53b9a2123fc6 lua/uloop: fd_add: use absolute indices for arguments
c0941d3289fc lua/uloop: make get_sock_fd capable of absolute addresses
161c25960ba2 lua/uloop: fd_add() better args checking
Signed-off-by: Petr Štetiar <ynezz@true.cz>
At this point in v5.4 kernel we cannot use dwc2_readl() and
dwc2_writel() since they rely on the value hsotg->needs_byte_swap
which cannot be obtained before the controller wakes up.
We should use readl() and writel() to wake up the controller before
calling dwc2_check_core_endianness().
Fixes: 6be0da90a1 ("ramips: refresh patches")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed Fixes: tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Quoting part of original message from eefb5f741015 commit in
linux-firmware repository:
This adds the "minifw" version of the EIP197 firmware, which the inside-
secure driver will use as a fallback if the original full-featured
firmware cannot be found. This allows for using the inside-secure driver
and hardware without access to "official" firmware only available under
NDA.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Firmware is binary blob, so there are barely any NULL terminated strings
expected, so we should probably convert all chars into u8 types, and
after that it's clear, that using strcpy doesn't make sense anymore.
This is rather theoretical stuff, but `uint8_t name[PART_NAME_LENGTH]`
means, that you can supply PART_NAME_LENGTH sized name, not
PART_NAME_LENGTH-1 name when NULL terminated.
Ref: https://github.com/openwrt/openwrt/pull/2274
Fixes: 04cb651376 ("firmware-utils: mkfwimage: fix more errors reported by gcc-6/7/9")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Compared to GCC 9:
870-ppc_no_crtsavres.patch changes moved to another file following upstream
881-no_tm_section.patch keep the tm section disabled
patches refreshed to apply cleanly
See https://gcc.gnu.org/gcc-10/porting_to.html for more info
Compiled and run tested on x86_64
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
Add needed config changes and tarball hash for new GCC version.
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
[added missing commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The block index of u-boot-env changed from mtd1 to mtd3 after upgrading kernel to 5.4.
This patch search the mtd block by label name, work as expect when perform a clean flash.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
At this moment Linksys EA8500 uses only eth0.
This patch change switch registers, which allow to use eth1 as lan
and eth0 as wan. The method work with similar Linksys EA7500V1
and it work with EA8500.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Brian Onn <brian.a.onn@gmail.com>
Tested-by: Adrian Panella <ianchi74@outlook.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This replaces deprecated backticks by more versatile $(...) syntax.
This does not touch lib/upgrade/nand.sh, as there replacement is
not trivial.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
3034eaf jail: use linux/capability.h instead of sys/capability.h
Fixes: b6e440a0f5 ("procd: update to git HEAD")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The support for this device's Marvell MV88E6060 switch has been
reported to be broken with kernels 4.19/5.4 (see bug report).
Since this a 4/32 device and it has been confirmed to be working
with stable 19.07 release (kernel 4.14), and since fixing it does
not seem trivial, let's just disable it in master.
Fixes: FS#2524
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Make sure RF5592 is set for RT5592 chip which apparently sometimes
doesn't have RF defined (but always comes with RF5592).
This patch was originally submitted on linux-wireless by
Tom Psyborg <pozega.tomislav@gmail.com> but got rejected.
Turns out the patch is actually needed.
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds support for the Netgear R6020, aka Netgear AC750.
The R6020 appears to be the same hardware as the Netgear R6080,
aka Netgear AC1000, but it has a slightly different flash layout,
and no USB ports.
Specification:
SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB
MAC addresses based on vendor firmware:
LAN *:88 0x4
WAN *:89
WLAN2 *:88 0x4
WLAN5 *:8a 0x8004
The factory partition might have been corrupted beforehand. However,
the comparison of vendor firmware and OpenWrt still allowed to retrieve
a meaningful assignment that also matches the other similar devices.
Installation:
Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6020, and power the R6020 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6020-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6020. After flashing has finished,
power cycle the R6020, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
[slightly extend commit message, fix whitespaces in DTS, align From:
with Signed-off-by]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes the gphy LED pins for Zyxel P-2812 devices. The have
been accidentally altered during a tidy-up operation (see Fixes:
below).
No ports were available, dmesg reported:
[ 0.658577] pinctrl-xway 1e100b10.pinmux: pin io5 already requested by
1e100bb0.stp; cannot claim for 1e108000.eth
[ 0.667566] pinctrl-xway 1e100b10.pinmux: pin-5 (1e108000.eth) status -22
[ 0.685238] lantiq,xrx200-net 1e108000.eth: Error applying setting,
reverse things back
[ 0.693270] lantiq,xrx200-net: probe of 1e108000.eth failed with error -22
Fixes: FS#3188
Fixes: 660200e53d ("lantiq: dts: assign the GPHY LED pins to the
Ethernet controller node")
Suggested-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Willem van den Akker <wvdakker@wilsoft.nl>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There was a bashism in the script. This fixes the script so that it
doesn't actually require bash, and can be run with any POSIX shell as
its shebang suggests.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Enable SCSI low-level drivers on targets that don't have it already in
order to fix following build failures on few platforms:
.config:4739:warning: symbol value 'm' invalid for SCSI_LOWLEVEL
* Restart config...
* SCSI low-level drivers
SCSI low-level drivers (SCSI_LOWLEVEL) [Y/n] (NEW) aborted!
Fixes: b88f8202c4 ("kernel: add iscsi-initator support")
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch is required for pcie@2,0 in mt7623 to work. The patch was originally
added in kernel 4.14, but it has not been ported to 4.19 and later.
Fixes: FS#3217
Tested-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Since commit 298814e6be ("base-files: config_generate: split macaddr with
multiple ifaces") uci MAC address setup will create a device node for each
member iface. But this script might override the device nodes and interfere
with the MAC address setup.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Commit e53ec043ba ("kirkwood: move usb support to modules") has moved
this config symbol into generic configs, so it could be removed from
other configs.
Suggested-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Port device support for DAP-1330 from the ar71xx target to ath79.
Additionally, images are generated for the European through-socket
case variant DAP-1365. Both devices run the same vendor firmware, the
only difference being the DAP_SIGNATURE field in the factory header.
The vendor's Web UI will display a model string stored in the flash.
Specifications:
* QCA9533, 8 MiB Flash, 64 MiB RAM
* One Ethernet Port (10/100)
* Wall-plug style case (DAP-1365 with additional socket)
* LED bargraph RSSI indicator
Installation:
* Web UI: http://192.168.0.50 (or different address obtained via DHCP)
There is no password set by default
* Recovery Web UI: Keep reset button pressed during power-on
until LED starts flashing red, upgrade via http://192.168.0.50
* Some modern browsers may have problems flashing via the Web UI,
if this occurs consider booting to recovery mode and flashing via:
curl -F \
files=@openwrt-ath79-generic-dlink_dap-1330-a1-squashfs-factory.bin \
http://192.168.0.50/cgi/index
The device will use the same MAC address for both wired and wireless
interfaces, however it is stored at two different locations in the flash.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Arduino Yun is a microcontroller development board, based on Atmel
ATmega32u4 and Atheros AR9331.
Specifications:
- MCU: ATmega32U4
- SoC: AR9331
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: SoC internal
- Ethernet: 1x 10/100Mbps
- USB: 1x 2.0
- MicroSD: 1x SDHC
Notes:
- Stock firmware is based on OpenWrt AA.
- The SoC UART can be accessed only through the MCU.
YunSerialTerminal is recommended for access to serial console.
- Stock firmware uses non-standard 250000 baudrate by default.
- The MCU can be reprogrammed from the SoC with avrdude linuxgpio.
Installation:
1. Update U-Boot environment variables to adapt to new partition scheme.
> setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
> setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
> saveenv
2. Boot into stock firmware normally and perform sysupgrade with
sysupgrade image.
# sysupgrade -n -F /tmp/sysupgrade.bin
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Some devices (e.g. Arduino Yun) need bitwise operations during MAC address
setup. This commit adds generalized versions of macaddr_setbit_la(), which
are helpful when manipulating a single bit in a MAC address.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Like many boards, the Banana Pi R2 doesn't have permanant storage of
its MAC address, and we store the first random one that the kernel
generates in order to use it later and at least be consistent.
Store it in the FAT boot partition, just as the U7623 board (and others)
do.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Instead of building in a default environment which loads our environment
from the FAT partition.... just ask U-Boot to do it.
Submitted upstream at
https://patchwork.ozlabs.org/project/uboot/list/?series=184688
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Rosen Penev
Eneas U de Queiroz
Petr Štetiar
Rui Salvaterra
Alexey Dobrovolsky
Tomasz Maciej Nowak
Syrone Wong
Pawel Dembicki
Huangbin Zhan
John Audia
Adrian Schmutzler
Daniel Golle
Tim Thorpe
Willem van den Akker
David Woodhouse
Lucian Cristian
Sungbo Eo
Sebastian Schaper