The Ubiquiti PowerBeam 5AC Gen 2 (PBE-5AC-Gen2) is an outdoor 802.11ac
5 GHz bridge with a radio feed and a dish antenna. The device is
hardware-compatible with the LiteBeam AC Gen2, plus the 4 extra LEDs.
Specifications:
- SoC: Qualcomm Atheros AR9342 rev 2
- RAM: 64 MB DDR2
- Flash: 16 MB SPI NOR (mx25l12805d)
- Ethernet: 1x 10/100/1000 Mbps Atheros 8035, 24 Vdc PoE-in
- WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff
- WiFi 2.4 GHz: Atheros AR9340 (SoC-based)
- Buttons: 1x (reset)
- LEDs: 1x power, 1x Ethernet, 4x RSSI via GPIO. All blue.
- UART: not tested
Installation from stock airOS firmware:
- Follow instructions for WA-type Ubiquiti devices on OpenWrt wiki
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[changed device name in commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In rt3883 subtarget, several devices add swconfig to their DEVICE_PACKAGES.
This is redundant as the package is already provided via DEFAULT_PACKAGES.
Remove the redundant inclusions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These definitions are not required since swconfig is selected for
the target anyway and kmod-swconfig is pulled as dependency by
kmod-switch-rtl8366rb.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit 8f6334eb94 ("ramips: explicitly disable built-in switch when needed")
did not fix rt288x and rt3883 devices. This patch deals with them.
While at it, consolidate duplicate cases in interface setup.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Three of the I-O DATA devices with NAND flash share a lot of
variables. Create a common definition for them to reduce duplicate
code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes following compile error:
```
CC drivers/net/ethernet/mediatek/mtk_eth_soc.o
drivers/net/ethernet/mediatek/mtk_eth_soc.c:70:5: error: conflicting types for 'mtk_m32'
u32 mtk_m32(struct mtk_eth *eth, u32 mask, u32 set, unsigned reg)
^~~~~~~
In file included from drivers/net/ethernet/mediatek/mtk_eth_soc.c:25:
drivers/net/ethernet/mediatek/mtk_eth_soc.h:964:6: note: previous declaration of 'mtk_m32' was here
void mtk_m32(struct mtk_eth *eth, u32 clear, u32 set, unsigned reg);
^~~~~~~
```
which caused by 5.4.34 mainlining of mtk_m32 function.
Fixes: faf668be35 ("kernel: bump 5.4 to 5.4.34")
Signed-off-by: Yong-hyu, Ban <perillamint@quendi.moe>
bef8f8a5966d mt76: mt7615: remove a stray if statement
89bd7199487f mt76: remove variable 'val' set but not used
ee8ac234b84e mt76: mt7615: introduce mt7615_mcu_fill_msg
4999db4668f0 mt76: mt7615: introduce mt7615_mcu_wait_response
8ce6e40eba03 mt76: mt7615: cleanup fw queue just for mmio devices
9d1d2ee9add3 mt76: mt7615: introduce mt7615_init_device routine
7fbd2a57cea4 mt76: always init to 0 mcu messages
3b277cf18d95 mt76: mt7615: introduce mt7615_mcu_send_message routine
2a4132a55a4f mt76: mt7615: add mt7615_mcu_ops data structure
9ba71749a122 mt76: mt7615: move mt7615_mcu_set_bmc to mt7615_mcu_ops
2e991f3e8cdd mt76: mt7615: move mt7615_mcu_set_sta in mt7615_mcu_ops
56852057cb90 mt76: mt7615: rely on skb API for mt7615_mcu_set_eeprom
642ecd978887 mt76: mt7615: rework mt7615_mcu_set_bss_info using skb APIs
2b0810af4a52 mt76: mt7615: move more mcu commands in mt7615_mcu_ops data structure
7a6285e63d88 mt76: mt7615: introduce MCU_FW_PREFIX for fw mcu commands
e536b42ebc7d mt76: mt7615: introduce mt7615_register_map
fccbdb628ffd mt76: mt7615: add mt7663e support to mt7615_reg_map
d42244e9255c mt76: mt7615: add mt7663e support to mt7615_{driver,firmware}_own
aebbe088127f mt76: mt7615: add mt7663e support to mt7615_mcu_set_eeprom
28e22d07f892 mt76: mt7615: introduce mt7615_eeprom_parse_hw_band_cap routine
167428592647 mt76: mt7615: introduce mt7615_init_mac_chain routine
23ca7acfc856 mt76: mt7615: introduce uni cmd command types
c4171728cf70 mt76: mt7615: introduce set_bmc and st_sta for uni commands
9e5c76d2310a mt76: mt7615: add more uni mcu commands
779b2cebc147 mt76: mt7615: introduce set_ba uni command
21ee7da00f0a mt76: mt7615: get rid of sta_rec_wtbl data structure
2097f74f664c mt76: mt7615: introduce mt7663e support
8e9cd01228d0 mt7615: sync Kconfig with upstream
3b4f93840950 mt76: add memory barrier to DMA queue kick
8d301ace8ed7 mt76: mt7615: fix mt7663e firmware struct endianness
9bc1850ce711 mt76: mt7615: fix endianness in unified command
a1b9b7d94aa0 mt76: mt7615: add missing declaration in mt7615.h
6e4b2a709fe7 mt76: sync Makefile with upstream
258dfb6afb30 mt76: mt76x02u: Add support for newer versions of the XBox One wifi adapter
9c3d84b62cc0 mt76: mt76x2u: introduce Mercury UD13 support
ea8ea71933ca mt76: mt76x0: pci: add mt7610 PCI ID
9d555f82d329 mt76: mt7615: modify mt7615_ampdu_stat_read for each phy
8bd26d6c3172 mt76: mt7615: enable aggr_stats for both phy
1315afa511e0 mt76: mt7615: cleanup mib related defines and structs
072b50c61e0e mt76: mt7615: add more useful Tx mib counters
b23ff3e9343a mt76: mt7663: fix mt7615_mac_cca_stats_reset routine
294abe47c9b2 mt76: mt7663: enable nf estimation
d2d7bf2243f6 mt76: mt7615: make scs configurable per phy
908a2cfab88f mt76: mt7663: disable RDD commands
eaef0a268b95 mt76: mt7615: add ethool support to mt7663 driver
96e07ef1113d mt76: mt7615: introduce mt7615_mcu_set_channel_domain mcu command
67182f36e3be mt76: mt7663: keep Rx filters as the default
e6a3f3ffe53a mt76: mt7615: introduce hw scan support
12ecd5ba2146 mt76: mt7615: introduce scheduled scan support
f6ab0bee3172 mt76: mt7615: introduce BSS absence event
f208a9430044 mt76: mt7615: introduce rlm tlv in bss_info mcu command
ea4f4d216dbe mt76: mt7615: remove unnecessary register operations
72c9380e70f9 mt76: add headroom and tailroom to mt76_mcu_ops data structure
63e14669e09d mt76: mt7615: introduce mt7663u support to mt7615_write_txwi
29d359ac7626 mt76: mt7615: introduce mt7615_mac_update_rate_desc routine
1f1dd2cb5b49 mt76: mt7615: introduce __mt7663_load_firmware routine
cb6dcfd3cf13 mt76: mt7615: move mt7615_mac_wtbl_addr in mac.h
d28e8e7ef912 mt76: mt76u: rely on mt7622 queue scheme for mt7663u
f78cf8957aba mt76: mt7615: rework wtbl key configuration
2829497aaaf5 mt76: mt7615: introduce mt7615_wtbl_desc data structure
02c9ec4a15e7 mt76: mt7615: add address parameter to mt7615_eeprom_init
e9c640c0a79e mt76: mt7663: correct the name of the rom patch
1e8b2fe5ab03 mt76: mt7615: do not always reset the dfs state setting the channel
ec0ea46dacf9 mt76: mt7615: Delete an error message in mt7622_wmac_probe()
d16a4698f1ac mt76: mt7615: disable merge of OTP ROM data by default
2b58998bb594 mt76: mt7615: add support for applying DC offset calibration from EEPROM
55198aafb756 mt76: mt7615: add support for applying tx DPD calibration from EEPROM
5a1eaa38d380 mt76: mt7603: disable merge of OTP ROM data by default
bf60f43b12fb mt76: mt76x2: disable merge of OTP ROM data by default
9406eb1d110f mt76: mt7615: fix endian issues in applying flash calibration data
66d00b8c9dac mt76: mt7615: fix possible division by 0 in mt7615_mac_update_mib_stats
25d812dddcf8 mt76: mt7663: fix aggr range entry in debugfs
08b8bd2bc915 mt76: mt7615: disable hw/sched scan ops for non-offload firmware
8fb1cd20a776 mt76: mt7615: set hw scan limits only for firmware with offload support
05b23d7478fe mt76: mt7615: rework IRQ handling to prepare for MSI support
b92c0d576769 mt76: mt7622: fix DMA unmap length
03daa60ca69c mt76: mt7663: fix DMA unmap length
5f2f676b1f01 mt76: mt7615: enable MSI by default
5822911f8026 mt76: remove unnecessary annotations
a7035bce8517 mt76: mt7615: fix possible deadlock in mt7615_stop
d4e6e225bc06 mt76: mt7615: move core shared code in mt7615-common module
94827d2033c7 mt76: mt7615: introduce mt7663u support
36591dd35f91 mt76: mt7615: enable scs for mt7663 driver
bd80144cb5be mt76: mt7615: disable aspm by default
9dcb60b78ede mt76: mt7615: provide aid info to the mcu
6e443e89cce2 mt76: remove PS_NULLFUNC_STACK capability
ea133325faa6 mt76: mt7663: introduce 802.11 PS support in sta mode
ff3869b38cf2 mt76: mt7615: make Kconfig entry obvious for MT7663E
01fd34f3a6c5 mt76: mt7615: fix sta ampdu factor for VHT
e5adbb2077e2 mt76: fix A-MPDU density handling
d73e3a23a54e mt76: mt7615: use larger rx buffers if VHT is supported
257319e9b07d mt76: mt7615: never use an 802.11b CF-End rate on 5GHz
29a92c5606d6 mt76: mt7603: never use an 802.11b CF-End rate on 5GHz
c0b19ac97c07 mt76: mt7615: adjust timing in mt7615_mac_set_timing to match fw/hw values
1656882f2723 mt76: mt7615: do not adjust MAC timings if the device is not running
4e7ce907faf3 mt76: mt7615: fix tx status rate index calculation
8304b3866100 mt76: mt7603: fix tx status rate index calculation
722d1f47d8ba mt76: add rx queues info to mt76 debugfs
da329ef776b0 mt76: mt7615: parse mcu return code for unified commands
facf74fd506f mt76: mt7615: fix mt7615_firmware_own for mt7663e
e910787a9888 mt76: mt7615: fix max wtbl size for 7663
c9821f7d6a8c mt76: mt7615: fix mt7615_driver_own routine
e35cc532c3d2 mt76: mt7615: fix aid configuration in mt7615_mcu_wtbl_generic_tlv
b6cb91a71fe1 mt76: mt7615: rework mt7615_mac_sta_poll for usb code
b193dd8100f8 mt76: mt7663u: enable AirTimeFairness
31cffa98920f mt76: mt7615: move mcu bss upload before creating the sta
cde3716aa47e mt76: enable TDLS support
1846da5dd417 mt76: mt7615: set spatial extension index
6aaf0299730f mt76: mt7615: fix endian issues in dcoc/txdpd calibration
5de75b745cf9 mt76: mt7663: fix up BMC entry indicated to unicmd firmware
a5f394c5ca48 mt76: mt7615: add sta pointer to mt7615_mcu_add_bss_info signature
1f2f3dda76b9 mt76: mt7615: fix event report in mt7615_mcu_bss_event
c2a3cced36de mt76: mt76x0: enable MCS 8 and MCS9
1afabe78cfc5 mt76: mt7663: add the possibility to load firmware v2
5f3ccc722627 mt76: mt7663: remove check in mt7663_load_n9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The official sysupgrade images for I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.) cannot be booted normally and the
kernel panics after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Note:
These devices use Z-LOADER to read the kernel from NAND flash and boot
it. Z-LOADER cannot load and start plain lzma-loader, so additional
lzma-compression is needed.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
In several Japanese routers with MT7621 SoC, the official sysupgrade
image cannot be booted properly after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This device has trouble extracting big kernel from flash,
and supports LZMA compressed kernels only.
Using OpenWrt kernel loader saves us 64 KB compared to the dictionary
size limiting workaround.
Factory image sizes (commit: 5f126c541a) with "CONFIG_ALL_KMODS=y":
- original ("-d23", default): 4784188 bytes, LZMA ERROR 1
- with "-d19": 4915260, LZMA ERROR 1
- with "-d18": 4915260, diff to original: +128 KB
- with "-d17": 4980796, diff to original: +192 KB
- with this patch: 4849724, diff to original: +64 KB
To save some CPU cycle, use minimal compression ("-a0") for the LZMA
compressed uImage.
The most robust solution would use a different loader,
which reads the compressed kernel directly from the flash.
See the thread at [0] for more details!
[0] http://lists.infradead.org/pipermail/openwrt-devel/2020-April/022926.html
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[fixed identation]
Signed-off-by: David Bauer <mail@david-bauer.net>
These boards suffer from a sudden inability to establish a link on the
SGMII. Enable the workaround to fix the link when it dies.
Signed-off-by: David Bauer <mail@david-bauer.net>
ath79 does not support kernels prior to 4.19 anymore.
Remove legacy code for those kernels from the ag71xx driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
This parser was added with the target, but no device seems to use it
currently, as all partitions are specified in the device-tree.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000:
- apply alphabetic sorting in multiple files
- use armada-3720 prefix for DTS like for other devices
- fix vendor capitalization for model in DTSes
- remove trivial comment in DTS files
- use DEVICE_VENDOR/DEVICE_MODEL
- remove redundant SUPPORTED_DEVICES
- use SOC instead of DEVICE_DTS
- remove empty line at EOF
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
NAND driver was dropped in the 5.4 bump, so enable it back
Fixes: 50c6938b95 ("bcm53xx: add v5.4 support")
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
This seems to be over 10 years old. It doesn't seem to be needed anymore.
Tested on malta with uClibc (selected BROKEN).
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Upstream commit dda9f4b9ca ("f2fs: fix to skip verifying block address
for non-regular inode").
On 4.14, attempting to perform operations on a non-regular inode
residing on an f2fs filesystem, such rm-ing a device node, would fail
and lead to a warning / call trace in dmesg. This fix was already
applied to other kernels upstream - including 4.19, from which the patch
was taken.
More info at https://bugzilla.kernel.org/show_bug.cgi?id=202495.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
ftp can cause problems on some networks switch primary download location
to https and add another mirror
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
also change the download source to https and add a mirror
drop merged patches
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[Add extra changes to compile on FreeBSD, merge two patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Before, only frames with a maximum size of 1528 bytes could be
transmitted between two 802.11s nodes.
For batman-adv for instance, which adds its own header to each frame,
we typically need an MTU of at least 1532 bytes to be able to transmit
without fragmentation.
This patch now increases the maxmimum frame size from 1528 to 1656
bytes.
Tested with two ath10k devices in 802.11s mode, as well as with
batman-adv on top of 802.11s with forwarding disabled.
Fix originally found and developed by Ben Greear.
Link: https://github.com/greearb/ath10k-ct/issues/89
Link: 9e5ab25027
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Build with NO_LIBCAP=1. This is to resolve build issue.
Package perf is missing dependencies for the following libraries:
libcap.so.2
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Although gdb is supported, gdbserver is still not.
checking whether gdbserver is supported on this host... no
Build breaks as gdbserver executable is not found during packaging.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and
Belkin F7C027 does not have a USB port anyway. Just drop it.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently SUPPORTED_DEVICES only contains the old device string. Fix it by
removing the first assignment.
Fixes: c2334ad60d ("ramips/mt76x8: Synchronize Makefiles with DTS compatible")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This service file has been misplaced from the very beginning.
Fixes: dcc34574ef ("oxnas: bring in new oxnas target")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
f4d759b dhcp.c: further improve validation
Further improve input validation for CVE-2020-11752
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
cdac046 dns.c: fix input validation fix
Due to a slight foobar typo, failing to de-reference a pointer, previous
fix not quite as complete as it should have been.
Improve CVE-2020-11750 fix
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
It was reported, that after image generation rework
x86-64-generic-squashfs-rootfs.img image won't boot on XenServer x86_64
anymore:
F2FS-fs (xvda): Magic Mismatch, valid(0xf2f52010) - read(0x84289960)
F2FS-fs (xvda): Can't find valid F2FS filesystem in 1th superblock
F2FS-fs (xvda): Magic Mismatch, valid(0xf2f52010) - read(0x4e8ee223)
F2FS-fs (xvda): Can't find valid F2FS filesystem in 2th superblock
List of all partitions:
ca00 4207 xvda
driver: vbd
No filesystem could mount root, tried:
ext3
ext2
ext4
squashfs
iso9660
f2fs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(202,0)
So lets fix this by adding back padding which was introduced in commit
a17d9482f5 ("x86: image: fix small disk space in squashfs overlay").
Ref: FS#3036
Fixes: 258f070d1a ("x86: fix missing squashfs and ext4 rootfs images")
Fixes: cb007a7bf6 ("x86: switch image generation to new code")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SFP cage of this device is connected via a AT8031 phy to port 5 of the switch.
This phy act as a RGMII-to-SerDes converter.
Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus.
SFP cage also has module detect pin which is connected to I2C gpio expander.
With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port.
NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding!
This means that some SGMII modules can work and only at forced 1GBit/full-duplex!
Signed-off-by: René van Dorst <opensource@vdorst.com>
This patch is needed for clause 37 1000Base-X encoding used in many SFP modules.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: René van Dorst <opensource@vdorst.com>
Commit 0543eb1110 ("imx6: 5.4: add missing kernel perf monitor
symbol") has added missing kernel config symbol FSL_IMX8_DDR_PMU which
is exposed only when building perf, so add it back.
Fixes: 8d9b36270b ("imx6: refresh kernel config")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
e2ed964 jail: don't fail unless requirejail is set
17e7ae7 jail: don't load libpreload-seccomp.so if it doesn't exist
Fixesopenwrt/packages#11913
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some boards using a QCA9556 or QCA9558 had their machine compatible
binding incorrectly set to qca,qca9557.
Signed-off-by: David Bauer <mail@david-bauer.net>
There are at least 3 different chips in the Scorpion series of SoCs.
Rename the common DTSI to better reflect it's purpose for the whole
series.
Also rename the compatible bindings from qca,ar9557 and qca,qca9557
to qca,qca9550.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes a few minor issues (partially cosmetic) in ltq-adsl and
ltq-adsl-fw Makefiles:
- fix PKG_SOURCE_URL and switch to https
- remove non-existant FW_NAME variable
- fix package name for config inclusion
- fix config symbol for debugging
Fixes: 1d0a9d0c04 ("move ltq-adsl")
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Like for myloader.c in the previous patch,
this patch moves tplinkpart.c to the kernel patches, so the
code and the kernel includes are at the same location and
the path can be adjusted per kernel.
While at it, remove some outdated kernel version switches from
the C code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Roger Pueyo Centelles
Adrian Schmutzler
Sungbo Eo
Yong-hyu, Ban
Felix Fietkau
INAGAKI Hiroshi
Szabolcs Hubai
David Bauer
DENG Qingfang
Li Zhang
Rosen Penev
Xiaobo Tian
Matt Merhar
weidong jia
Lucian Cristian
Linus Lüssing
Yangbo Lu
Luiz Angelo Daros de Luca
Kevin Darbyshire-Bryant
Petr Štetiar
René van Dorst
Daniel Golle