Switches failsafe mode interface from WAN to LAN ports.
Tested on TL-WR940Nv6.0 and TL-WR940Nv6.1
Signed-off-by: Joachim Fünfer <joachim.fuenfer@stusta.net>
This corrects the PLL value for 10 Mbit/s links on the OCEDO Raccoon.
Prior to this patch, 10 Mbit/s links would not transmit data.
It is worth mentioning that the vendor firmware used the same PLL
settings and 10Mbit/s was also not working there.
All other link-modes are working correctly without any packet loss.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit fixes following script error in syslog:
cat: can't open '/sys/devices/platform/ehci-platform/usb1/1-1/1-1.2/1-1.2:1.4/ieee80211/phy*/name': No such file or directory
sh: add: unknown operand
sh: add: unknown operand
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[commit subject and message tweaks]
Upstream has renamed UPROBE_EVENT to UPROBE_EVENTS in the following
commit:
commit 6b0b7551428e4caae1e2c023a529465a9a9ae2d4
Author: Anton Blanchard <anton@samba.org>
Date: Thu Feb 16 17:00:50 2017 +1100
perf/core: Rename CONFIG_[UK]PROBE_EVENT to CONFIG_[UK]PROBE_EVENTS
We have uses of CONFIG_UPROBE_EVENT and CONFIG_KPROBE_EVENT as
well as CONFIG_UPROBE_EVENTS and CONFIG_KPROBE_EVENTS.
Consistently use the plurals.
So I'm changing it to this plural option in order to make kconfig happy
and stop asking about it if kernel is compiled with verbose logging:
Enable uprobes-based dynamic events (UPROBE_EVENTS) [Y/n/?] (NEW)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
No target is using kernel 3.18 anymore, remove all the generic
support for kernel 3.18.
The removed packages are depending on kernel 3.18 only and are not used on
any recent kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 4.1, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target adds an alternative mmc driver using a patch.
Within this patch, a definition got renamed upstream.
Change it to fix following compile error:
CC drivers/mmc/host/bcm2835-mmc.o
In file included from ./include/linux/kernel.h:14:0,
from ./include/linux/delay.h:22,
from drivers/mmc/host/bcm2835-mmc.c:25:
drivers/mmc/host/bcm2835-mmc.c: In function 'bcm2835_mmc_dumpregs':
drivers/mmc/host/bcm2835-mmc.c:254:27: error: 'SDHCI_ACMD12_ERR' undeclared (first use in this function); did you mean 'SDHCI_CMD_CRC'?
bcm2835_mmc_readw(host, SDHCI_ACMD12_ERR),
^
./include/linux/printk.h:137:18: note: in definition of macro 'no_printk'
printk(fmt, ##__VA_ARGS__); \
^~~~~~~~~~~
drivers/mmc/host/bcm2835-mmc.c:253:2: note: in expansion of macro 'pr_debug'
pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
^~~~~~~~
drivers/mmc/host/bcm2835-mmc.c:254:27: note: each undeclared identifier is reported only once for each function it appears in
bcm2835_mmc_readw(host, SDHCI_ACMD12_ERR),
^
./include/linux/printk.h:137:18: note: in definition of macro 'no_printk'
printk(fmt, ##__VA_ARGS__); \
^~~~~~~~~~~
drivers/mmc/host/bcm2835-mmc.c:253:2: note: in expansion of macro 'pr_debug'
pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
^~~~~~~~
scripts/Makefile.build:326: recipe for target 'drivers/mmc/host/bcm2835-mmc.o' failed
make[8]: *** [drivers/mmc/host/bcm2835-mmc.o] Error 1
Upstream commit:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.14.114&id=45fd8679ea86bffb352132a1df4917c3d11375aa
Fixes: b765f4be40 ("kernel: bump 4.14 to 4.14.114")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Since ct->proto.tcp.last_win isn't updated when nf_ct_tcp_no_window_check is
enabled, the retransmission timeout check needs to be bypassed.
Based on patch by Rob Mosher
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The option is at the moment enabled for x86/64. The selection chain
should be
config RETPOLINE
select STACK_VALIDATION if HAVE_STACK_VALIDATION
config x86
select HAVE_STACK_VALIDATION if X86_64
cryptdev-linux:
make[4]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10'
make -C /store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.113 M=/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10 ARCH=x86 CROSS_COMPILE=x86_64-openwrt-linux-musl- modules
make[5]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.113'
make[6]: *** No rule to make target '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10/ioctl.o', needed by '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10/cryptodev.o'. Stop.
Makefile:1533: recipe for target '_module_/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10' failed
Open vSwitch intree kmods
make[7]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux'
make -C /store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.111 ARCH=x86 M=/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux modules
make[8]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.111'
make[9]: *** No rule to make target 'tools/objtool/objtool', needed by '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux/actions.o'. Stop.
Makefile:1533: recipe for target '_module_/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux' failed
make[8]: *** [_module_/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux] Error 2
make[8]: Leaving directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.111'
Reference: builddeb: include objtool binary in headers package, https://patchwork.kernel.org/patch/9014071/
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Refreshed all patches.
New symbols:
- CONFIG_LDISC_AUTOLOAD
- CONFIG_PPC_BARRIER_NOSPEC
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This patch fixes disfunctional WLAN LED on TP-Link W8970. The LED was
reported working in the CC release[1], but doesn't work anymore in 18.06.2.
1. 420cb24d41
Tested-by: Damian Janarek <dzanar18@o2.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Both targets have their own idea of how to use ehci-fsl.
This patch reverts part of commit
68b8d3b079 ("kernel: usb: add FSL EHCI package") and moves
ehci-fsl back into kmod-usb2, while also making it hopefully
useable for the mpc85xx target.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The current mpc85xx build is failing because the
TL-WDR4900v1 kernel image no longer fits into the
partition. Extending the kernel is not possible
without updating u-boot's kernel loader commands.
This patch disables the WDR4900v1 until the kernel
image size issue is fixed so the buildbot can still
compile the Sophos RED 15w Rev.1 . Installing the
WDR4900v1 images would cause the routers to get
bricked.
For the discussion, please go to:
<https://github.com/openwrt/openwrt/pull/1773>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently it's not possible to use perf on ath79 due to genirq flags
mismatch happening on static virtual IRQ 13 which is used for
performance counters hardware IRQ 5.
On TP-Link Archer C7v5:
CPU0
2: 0 MIPS 2 ath9k
4: 318 MIPS 4 19000000.eth
7: 55034 MIPS 7 timer
8: 1236 MISC 3 ttyS0
12: 0 INTC 1 ehci_hcd:usb1
13: 0 gpio-ath79 2 keys
14: 0 gpio-ath79 5 keys
15: 31 AR724X PCI 1 ath10k_pci
$ perf top
genirq: Flags mismatch irq 13. 00014c83 (mips_perf_pmu) vs. 00002003 (keys)
On TP-Link Archer C7v4:
CPU0
4: 0 MIPS 4 19000000.eth
5: 7135 MIPS 5 1a000000.eth
7: 98379 MIPS 7 timer
8: 30 MISC 3 ttyS0
12: 90028 INTC 0 ath9k
13: 5520 INTC 1 ehci_hcd:usb1
14: 4623 INTC 2 ehci_hcd:usb2
15: 32844 AR724X PCI 1 ath10k_pci
16: 0 gpio-ath79 16 keys
23: 0 gpio-ath79 23 keys
$ perf top
genirq: Flags mismatch irq 13. 00014c80 (mips_perf_pmu) vs. 00000080 (ehci_hcd:usb1)
This problem is happening, because currently statically assigned virtual
IRQ 13 for performance counters is not claimed during the initialization
of MIPS PMU during the bootup, so the IRQ subsystem doesn't know, that
this interrupt isn't available for further use.
So this patch fixes the issue by simply booking hardware IRQ 5 for MIPS PMU.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Reverting this commit as I've missed the fact, that the button is
already present in the included DTSI file.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or
Vocore2.
Specification:
CPU: MT7628 580 MHz. MIPS 24K
RAM: 64 MB
Flash: 8 MB
WIFI: 802.11n/g/b 20/40 MHz
USB: 1x Port USB 2.0
Ethernet: 5 Port ethernet switch
UART: 2x
Installation: Use the installed uboot Bootloader. Connect a serial cable
to serialport 0. Turn power on. Choose the option: "Load system code
then write to Flash via TFTP". Choose the local device IP and the TFTP
server IP and the file name of the system image. After if the
Bootloader will copy the image to the local flash.
Notes: The I2C Kernel module work not correctly. You can send and
receive data. But the command i2cdetect doesn’t work. FS#845
Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com>
[commit subject and message touches, DTS whitespace fixes, wifi LED
rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses,
removed i2c kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: MediaTek MT7628NN
RAM: 64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED: Power - WLAN
BTN: Reset
UART: 115200 8N1
TX and RX are labled on the board as pads next to the SoC
Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
Note: The ethernet port is by default WAN. So you need to connect to
the router via WiFi
2. Navigate to the Update tab on the left side.
3. Select "Local Update"
4. Upload the OpenWrt sysupgrade image.
Note: Make sure you select not to preserve the configuration.
Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
Wait for the LED to flash 5 times.
2. Assign yourself a static IPv4 in 192.168.1.0/24
3. Upload the OpenWrt sysupgrade image at 192.168.1.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link TL-WDR 4900 have u-boot with read-only env.
Boot command read only 0x29F000 data from flash.
Bigger images causes crc error. It can't be changed.
This patch add kernel size checking.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [utilize KERNEL_SIZE]
Remove wireless and USB packages from the device-specific package
selection as they are already selected by the target itself.
Signed-off-by: David Bauer <mail@david-bauer.net>
This removes USB support from the compiled kernel. Because of this, the
kernel is just small enough for the TP-Link WDR4900 to boot the
resulting kernel.
This is necessary to support the WDR4900 in the upcoming 19.xx release.
In the long run, this should be fixed with a second stage bootloader, as
the vendor bootloader only loads the first 2684k bytes.
Signed-off-by: David Bauer <mail@david-bauer.net>
I-O DATA ETG3-R is a wired router. So wireless-related packages are
unnecessary and remove those packages from default configuration to
reduce flash usage.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This adds support for the TP-Link WR842N v3 which is already supported on ar71xx
target (0b45bec22c).
Specification:
* SoC: QCA9533 ver 2 rev 0
* 16 MB Flash (gd25q128)
* 64 MB RAM
* 1 WAN 10/100 MBit/s (blue connector)
* 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors)
* Atheros AR9531 (2,4GHz, two fixed antennas)
* USB
* Reset / WPS button
* WiFi button (rf kill)
* 8 green leds; 1 red/green led
* serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed)
Installation:
* flash via vendor WebUI (the filename must not exceed certain length)
* sysupgrade from installed OpenWrt (also ar71xx)
Thanks to Holger Drefs for providing the hardware
Tested-by: @kofec (github)
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
Instead of assigning I2C pins as GPIOs by default, leave it up to the
user whether to install kmod-i2c-mt7621 and use them for hardware I2C
instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.
Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A
Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Remove Netgear-specific image build variables which are set to the same
value.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[reordering of variables, removed stray newline]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This device shares the network config with v4, thus the WAN MAC
also needs to be fixed the same way. However, the partition
where the MAC address resides has been changed.
Based on: https://github.com/openwrt/openwrt/pull/1726
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These devices share the network config with C7v4, thus the WAN MAC
also needs to be fixed the same way. However, the partition
where the MAC address resides has been changed.
Based on: https://github.com/openwrt/openwrt/pull/1726
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The GPIO for the reset button for the Archer C7v5 changed from
ar71xx to ath79. An investigation based on tests revealed
that the A7v5 responds on "11", while the C7v5 responds on
"5" as set for ar71xx.
Thus, we just define this in the DTS files instead of in the
common DTSI.
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Definition is split here without obvious reason. Just merge it
(and align order to that from C7 v4).
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal
2x2 MIMO antennas. It can be supplied via a USB connector or via PoE.
There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an
optional PoE passthrough from the first LAN port to the WAN port.
SoC: Qualcomm / Atheros QCA9533-BL3A
RAM: 64 MB DDR2
Flash: 16 MB SPI NOR
Ethernet: 4x 10/100 Mbps (1 WAN + 3 LAN)
LEDS: 1x via a SPI controller (not yet supported)
Buttons: 1x Reset
Serial: 1x (only RX and TX); 115200 baud, 8N1
Missing points:
- LED not yet supported
- Factory upgrade via web IF or TFTP recovery not yet supported
(Needs RSA signed images, for details see PR#1958)
The serial port is on a four pin connextor labeled J1 and located
between Ethernet and USB connector. The pinout is:
1. 3V3 (out)
2. Rx (in)
3. Tx (out)
4. GND
Upgrading via serial port / U-Boot:
- Connect the serial port via a level converter
- Power the system and stop U-Boot with pressing any key when `Hit any
key to stop autoboot` is displayed. Note: Pressing space multiple
times untill U-Boot reaches that location works well.
- Connect a PC with the IP 192.168.1.100 (or some other in that net)
running a TFTP-Server to one of the LAN ports. Copy the sysupgrade
image to the server.
- Set the U-Boot server IP with
setenv serverip 192.168.1.100
- Load the flash image to RAM with
tftpboot 0x81000000 sysupgrade.bin
- Erase the flash with
erase 0x9f050000 0x9ffaffff
- Write the new flash content with
cp 0x81000000 0x9f050000 ${filesize}
- Reset the device with
reset
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
[removed full stop in subject and added lockdown note to commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SOC: Qualcomm Atheros QCA9558
RAM: 128MB
FLASH: 16MB (Macronix MX25L12845EMI-10G)
WLAN1: QCA9558 2.4GHz 802.11bgn 3SS
WLAN2: QCA9880 5GHz 802.11ac 3SS
LED: Power, LAN1, LAN2, 2.4GHz, 5GHz
Serial:Next to SPI Flash,
Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3)
The Serial setting is 115200-8-N-1
INSTALLATION:
1. Serve an OpenWrt ramdisk image named "ursus.bin".
Set your IP-address to 192.168.100.8/24.
2. Connect to the serial. Power up the device and interrupt
the boot process.
3. Set the correct bootcmd with
> setenv bootcmd run bootcmd_1
> saveenv
4. Run
> tftpboot 0x81000000 ursus.bin
> bootm 0x81000000
5. Wait for OpenWrt to boot up.
6. Transfer OpenWrt sysupdate image and flash via sysupgrade.
Signed-off-by: Markus Scheck <markus.scheck1@gmail.com>
Tested-by: David Bauer <mail@david-bauer.net>
[whitespace fix, renamed LED labels and SoC type fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In ar71xx we check for stuck DMA on devices which fall in the is_ar724x
SoC group (ar724x, ar933x, ar934x, qca9533, tp9343, qca955x, qca956x).
In ath79 we're currently performing this check only for devices with
ar7240 SoC, so this patch tries to sync the dma stuck checking behavior
with what is being done in ar71xx.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It was reported, that latest ar71xx builds have broken networking on
TP-Link TL-WPA8630 and Nanostation M5 XW devices and that by reverting
the offending commit, everything is back to normal.
Fixes: d3506d1 ("ar71xx: ag71xx: fix compile error when enabling debug")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART: 1 UART on PCB marked as J1 with 115200 8N1 config
LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
UART connection details
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions using recovery method over TFTP
1. Unplug the ethernet cable from the router.
2. Using paper clip press and hold the router's reset button. Make sure
you can feel it depressed by the paper clip. Do not release the button
until step 4.
3. While keeping the reset button pressed in, plug the ethernet cable
back into the AP. Keep the reset button depressed until you see the
device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
LED2/LED4), this may take up to 25 seconds.
4. You may release the reset button, now the device should be in TFTP
transfer mode.
5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
should work.
6. Plug the PoE injector's LAN cable directly to your computer.
7. Start tftp client and issue following commands:
tftp> binary
tftp> connect 192.168.1.20
tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin
Tested only on Bullet M2HP.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is backport of the same functionality in ath79, from commit
d42a7c469 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP
recovery method")
Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:
All future airOS versions will be signed in this way and not allow
unsigned firmware to be loaded except via TFTP.
U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:
Hit any key to stop autoboot: 0
Setting default IP 192.168.1.20
Starting TFTP server...
Receiving file from 192.168.1.25:38438
Received 4981148 bytes
Firmware check failed! (1)
By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:
Received 3801500 bytes
Firmware Version: XW.ar934x.v6.0.4-42.OpenWrt-r9766+2-be42e44
Setting U-Boot environment variables
Un-Protected 1 sectors
Erasing Flash.... done
Patch provided by AREDN[3] project, tested on Bullet M2 XW.
1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds support for the following computer on modules (CoM) from
Toradex[A]:
Apalis iMX6 Quad 2GB IT - i.MX 6Quad 800MHz, 2GB DDR3, 4GB eMMC
-40° to +85° C Temp
Apalis iMX6 Quad 1GB - i.MX 6Quad 1GHz, 1GB DDR3, 4GB eMMC
0° to +70° C Temp
Apalis iMX6 Dual 1GB IT - i.MX 6Dual 800MHz, 1GB DDR3, 4GB eMMC
-40° to +85° C Temp
Apalis iMX6 Dual 512MB - i.MX 6Dual 1GHz, 512MB DDR3, 4GB eMMC
0° to +70° C Temp
I've developed and tested it on Quad 2GB IT v1.1A and Dual 512MB v1.1A
CoMs, using Ixora[B] carrier board v1.0A, but it should hopefuly work on
Eval[C] board as well.
A. https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-freescale-imx-6
B. https://www.toradex.com/products/carrier-board/ixora-carrier-board
C. https://www.toradex.com/products/carrier-board/apalis-evaluation-board
Flashing/recovery instructions:
1. Download and compile imx_loader for OpenWrt from
https://github.com/ynezz/imx_loader
2. Enter recovery mode as desribed in
https://developer.toradex.com/knowledge-base/imx-recovery-mode
3. Connect board via USB to the host computer, check that it's connected
by lsusb:
15a2:0054 Freescale Semiconductor, Inc. i.MX 6Dual/6Quad SystemOnChip
in RecoveryMode
4. Copy following OpenWrt images to imx_loader directory:
SPL
u-boot.img
u-boot-with-spl.imx
openwrt-imx6-apalis-recovery.scr
openwrt-imx6-apalis-squashfs.combined.bin
5. Run imx_usb in imx_loader directory
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add switch definition for the rtl8367b switch to the DTS/DTSi for
the Belkin F9K1109v1 that was mistakenly omitted from the initial
commit.
Fixes: 017ec068e3df (ramips: add support for Belkin F9K1109v1)
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Upstream driver has gone through a series of cleanup and was moved
from drivers/staging into drivers/spi. Backport it to replace our
messy driver.
Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de>
[LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module]
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Tian Xiao bo <peterwillcn@gmail.com>
[Newifi-D2 MediaTek MT7621 ver:1 eco:3]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Currently, tplink-safeloader definition is only used a base for
another common definition.
This patch adjusts tplink-safeloader so it can be actually used
for some targets in generic-tp-link.mk.
This patch is cosmetic except for the order of
"check-size $$$$(IMAGE_SIZE)" and "append-metadata" exchanged
for the tplink_re350k-v1 .
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [dealed with
tplink_cpe210-v2 and tplink_cpe210-v3, removed tplink-safeloader-uimage's
extra IMAGE/sysupgrade.bin rule]
Enable the USB power for the Netgear R6120. Otherwise, no power is
supplied to an attached USB device.
Signed-off-by: David Bauer <mail@david-bauer.net>
With transition from ar71xx to ath79 some of devices change their naming
of LEDs. When upgrading from ar71xx target images this will require the
user to adjust previously working configuration. This commit adds
migration script which can be used to rename old names to new ones.
With this previously working configuration will be automatically
adjusted, wihtout user intervention.
This commit adds migration case for EnGenius EPG5000, the wireless LEDs
names have changed from epg5000:blue:wlan2-g and epg5000:blue:wlan-5g to
epg5000:blue:wlan2g and epg5000:blue:wlan5g.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Hardware spec:
CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0
Flashing instructions:
Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692
to get the bootloader and unlock firmware.
0. upgrade your router with the telnet firmware via the
firmware upgrade page on the webui.
1. telnet 192.168.11.1 from your PC
2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer
it to the /tmp directory of the router.
3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader
4. turn off the power
5. Push the reset button while turning on the router and
wait until LED start blinking (~10sec.)
6. Connect Ethernet port and goto http://192.168.1.1.
7. Upload the firmware to firmware restore page in webui.
Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
This commit adds support for Linux 4.19 kernel, various cleanups
listed below.
Drop 170-cisco-hack.patch as these devices never seems to have been
supported.
Unset kernel symbols:
* CONFIG_CAVIUM_CN63XXP1=y
No supported hardware uses CN63XXP1 and it causes "slight decrease in
performance"
Source: https://cateee.net/lkddb/web-lkddb/CAVIUM_CN63XXP1.html
* CONFIG_USB_OCTEON_EHCI=y
CONFIG_USB_OCTEON_OHCI=y
Deprecated
Source: https://cateee.net/lkddb/web-lkddb/USB_OCTEON_EHCI.htmlhttps://cateee.net/lkddb/web-lkddb/USB_OCTEON_OHCI.html
Removed kernel symbols:
* # CONFIG_ARCH_HIBERNATION_POSSIBLE=y
* CONFIG_ARCH_SUSPEND_POSSIBLE=y
These are not in if you do a vanilla config of a MIPS Octeon kernel
and I can't find any references about support on this platform.
* # CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
* CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
No need to have this in by default, not defined in most other targets
* CONFIG_CRASH_CORE=y
Can't find any documentation why this should be enabled by default
* CONFIG_DEBUG_INFO=y
Set by https://github.com/openwrt/openwrt/blob/master/config/Config-kernel.in#L134
* CONFIG_DEBUG_SPINLOCK=y
No need to have this in by default
* CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=120
Already set by default
Source: https://cateee.net/lkddb/web-lkddb/DEFAULT_HUNG_TASK_TIMEOUT.html
* CONFIG_DETECT_HUNG_TASK=y
No need to have this in by default, not defined in most other targets
* CONFIG_HAVE_DEBUG_KMEMLEAK=y
No need to have this in by default, not defined in most other targets
* CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
No need to have this in by default
* CONFIG_HAVE_IDE=y
None of the supported devices have IDE
* CONFIG_HZ=250
* # CONFIG_HZ_100 is not set
* CONFIG_HZ_250=y
This is broken with generic config
* CONFIG_KALLSYMS=y
No need to have this in by default, not defined in most other targets
* CONFIG_KEXEC=y
* CONFIG_KEXEC_CORE=y
No need to have this in by default, not defined in most other targets
* CONFIG_HAVE_KVM=y
No need to have this in by default
* CONFIG_SCHED_DEBUG=y
No need to have this in by default, not defined in most other targets
* CONFIG_SYSFS_DEPRECATED=y
Deprecated symbol
Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED.html
* CONFIG_SYSFS_DEPRECATED_V2=y
Discouraged usage in general
Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED_V2.html
* CONFIG_UNINLINE_SPIN_UNLOCK=y
No need to have this in by default, not defined in most other targets
Source: https://github.com/openSUSE/kernel/blob/master/lib/Kconfig.debug#L1137
* CONFIG_ZLIB_INFLATE=y
No need to have this in by default, not defined in most other targets
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Currently sysupgrade overwrites whole disk and destroys partitions added
by user. Sync the sysupgrade code with the one present in x86 target to
remedy this behaviour.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since some boards could be also booted from other mediums than SD card,
lets make the upgrade block device autodetected.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since most of devices using SD card image to boot, use ext4 as boot
files system we can drop fat fs related packages. Also move packages
which are added repeatedly across subtargets to their default packages,
with droping the ones that are enabled in target kernel configugation.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This will allow to drop additional packages and shrink image size.
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The options are managed on a generic way by the can
kmod packages
Additionally, select can packages only for devices that
currently has CAN enabled, which is only the ZC702
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The options are managed on a generic way by video packages
Additionally, only one of the currently supported boards
has a camera interface, but it requires programming
the FPGA fabric first
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The options are managed on a generic way by the sound
kmod packages
Additionally, none of the currently supported boards have
sound support out of the box, as they require programming
the FPGA fabric first
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
It is a small form factor computer with rich amount of expansion ports.
Some hardware specs and supported features in this commit:
CPU: NVIDIA Tegra 2 @ 1GHz
RAM: 1GB DDR2-667
Storage: SDHC card slot
µSDHC card slot
USB to SATA bridge (depends on model)
1MB SPI NOR flash for bootloader (single partition)
LAN: RTL8111DL GbE
WIFI: RT3070 b/g/n with external antenna (depends on model)
RTC: EM3027 (mapped as rtc0; with battery backup)
Tegra 2 built-in (mapped as rtc1)
Sound: Analog/Digital (TLV320AIC23b; S/PDIF not tested)
Connectors: 4x USB 2.0
RS232 (mini serial)
HDMI
DVI-D (depends on model, not supported atm)
Extension connector (24 pin ZIF, 0.5mm pitch):
2X UART
SPI
JTAG (1.8V)
Other: power button with green led (not functional for early revisions
without programmed PMIC)
2x GPIO configurable green led
TrimSlice uses U-Boot placed in NOR flash. Boots Linux from any media
connected to USB, SATA or SD card inserted in slot. Can also boot from
TFTP. To run OpenWrt one needs to update U-Boot to fairly recent version
(the versions, pre-dts/dts provided by CompuLab won't suffice):
1. Boot TrimSlice into Your current linux distro,
2. Download trimslice-spi.img from u-boot-trimslice subdir,
3. Install mtd-utils,
4. Run following commands:
flash_erase /dev/mtd0 0 256
nandwrite /dev/mtd0 trimslice-spi.img
5. Poweroff, insert SD card with OpenWrt, boot and enjoy.
If by some obstacle You can't follow those instructions, it is possible
to flash U-Boot using serial console.
1. Insert FAT or EXT2/EXT3 formatted SD card with trimslice-spi.img,
2. Interrupt boot process to enter U-Boot command line,
3. Run following commands:
${fs}load mmc 0 0x04080000 trimslice-spi.img
sf probe 0
sf erase 0 0x100000
sf write 0x04080000 0x0 ${filesize}
reset
4. Poweroff, insert SD card with OpenWrt, boot and enjoy.
If something went wrong with one of above steps, there is simple
recovery option:
1. Open the µSD slot security door to access the recovery-boot button,
2. Insert SD card with OpenWrt to the front slot while unpowered,
3. Power on the TrimSlice while pressing the recovery-boot button,
4. With this it should boot straigth to OpenWrt, from there download
trimslice-spi.img and execute following commands:
mtd erase /dev/mtd0
mtd write trimslice-spi.img /dev/mtd0
5. Reboot, now it should boot straigth to OpenWrt, without pressing the
recovery-boot button, with proper U-Boot flashed.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Add U-Boot for NVIDIA Tegra based boards, with the first being CompuLab
TrimSlice. This is part of initial support for this board.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
New target introduces initial support for NVIDIA Tegra SoC based devices.
It focuses on Tegra 2 CPUs, for successors supporting NEON instruction
set the target should be split in two subtargets.
This initial commit doesn't create any device image, it's groundwork
for further additions.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
It adjusts b53 code to upstream changes from the commit 3c1bcc8614db
("net: ethernet: Convert phydev advertize and supported from u32 to link
mode").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Please note that modified code isn't currently being compiled with
kernels 4.19+ due to the dropped CONFIG_NF_CONNTRACK_IPV6 in upstream
Linux. That requires a separated fix.
This fixes:
net/netfilter/nf_conntrack_rtcache.c: In function 'nf_rtcache_get_cookie':
net/netfilter/nf_conntrack_rtcache.c:82:11: error: 'const struct rt6_info' has no member named 'rt6i_node'; did you mean 'rt6i_idev'?
if (rt->rt6i_node)
^~~~~~~~~
rt6i_idev
IPv6 structs were reworked in upstream kernel by:
commit a64efe142f5e ("net/ipv6: introduce fib6_info struct and helpers")
commit 77634cc67dc1 ("net/ipv6: Remove unused code and variables for rt6_info")
commit 93c2fb253d17 ("net/ipv6: Rename fib6_info struct elements")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
This is based on the support patch for the identical CPE210 v3
by Mario Schroen <m.schroen@web.de>.
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
* SoC: Qualcomm Atheros QCA9533 (650MHz)
* RAM: 64MB
* Storage: 8 MB SPI NOR
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI or TFTP
To get to TFTP recovery just hold reset button while powering
on for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Thanks to robimarko for the work inside the ar71xx tree.
Thanks to adrianschmutzler for deep discussion and fixes.
Signed-off-by: Mario Schroen <m.schroen@web.de>
[Split into DTS/DTSI, read-only config partition in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename, light subject touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Looks identical to the v2.
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[Rebased, adjusted for separate tplink-safeloader entry, dynamic partitioning]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is also helpful to add support in ath79.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
I've missed leading whitespace issues in the original patch, so fixing
it in this commit. Thanks to pepe2k for letting me know.
Fixes: d260813d ("ar71xx: ens202ext: Fix VLAN switch")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This adds the SPDX license identifier for the NETGEAR EX6150. It was
missed when submitting the original patch.
Signed-off-by: David Bauer <mail@david-bauer.net>
The target ENS202EXT was just recently added right before the stable
release of Openwrt 18.
It flashes fine, but the physical switch is almost impossible to use
until you have a VLAN set up. Tested on two devices.
The actual problem is that eth0 represents nothing for whatever reason.
In other words, both WAN and LAN are running from eth1. There may be an
underlying problem in the build, but for now, I assume that this is
correct and that a VLAN switch is an appropriate fix.
Also, it's virtually impossible to get the switch running right through
LuCI. It is one thing to get a switch to appear, but attempting to
configure it breaks the whole thing. The VLAN has to be set up
perfectly, otherwise, interfaces will not start up, and one is forced to
reset settings, OR, the new LuCI feature kicks in and reverses any
steps. It is extremely difficult to determine which virtual ports
correspond to which physical ethernet ports without being able to set up
the switch in LuCI.
Temporary Workaround: followed directions here
[openwrt/luci#867](https://github.com/openwrt/luci/issues/867)
Reviewed-by: Marty Plummer <hanetzer@startmail.com>
Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[commit author fix, subject fix, message text wrap]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The specific flash chip used (W25Q256FVEM) accepts 50MHz for read
requests and higher for others. 104MHz for fast reads. ramips seems to
be limited to 80MHz based on testing with higher values (no speedup).
Based on upstream commit: 97738374a310b9116f9c33832737e517226d3722
time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s
[test done with backported upstream v4.19 driver[1], for numbers on
stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI
frequency to 80MHz` commit message]
1. https://github.com/openwrt/openwrt/pull/1578
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[expanded note about spi driver version]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The flash chip on the board (Spansion S25FL256SAIF00) is rated to
support at least 50MHz for normal read requests according to the
datasheet. 133MHz for fast reads. However, ramips seems to be limited to
80MHz.
>From testing this, higher values do not improve speeds.
time dd if=/dev/mtdblock3 of=/dev/null bs=64k from
42.82s to 14.09s.
boot speed is also faster:
[ 66.884087] procd: - init - vs
[ 48.976049] procd: - init -
Since spi speed was requested:
[ 3.538884] spi-mt7621 1e000b00.spi: sys_freq: 225000000
CPU is 900MHz:
[ 0.000000] CPU Clock: 900MHz
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[fixed commit message by adding missing 0 in the spi-mt7621 clock output]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7621
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: MediaTek MT7662E bgn 2SS
WiFi: MediaTek MT7662E nac 2SS
BTN: ON/OFF - Reset - WPS - AP/Extender toggle
LED: - Arrow Right (blue)
- Arrow Left (blue)
- WiFi 1 (red/green)
- WiFi 2 (red/green)
- Power (green/amber)
- WPS (Green)
UART: UART is present as Pads on the backside of the PCB. They are
located on the other side of the Ethernet port.
3.3V - GND - TX - RX / 57600-8N1
3.3V is the nearest one to the antenna connectors
Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).
You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash
Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Device specification:
- SoC: RT5350F
- CPU Frequency: 360 MHz
- Flash Chip: Winbond 25Q32 (4096 KiB)
- RAM: 32768 KiB
- 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
- 1x external, non-detachable antenna
- UART (J1) header on PCB (57800 8n1)
- Wireless: SoC-intergated: 2.4GHz 802.11bgn
- USB: None
- 3x LED, 2x button
Flash instruction:
1. Configure PC with static IP 192.168.1.2/24 and start TFTP server.
2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin"
to "kstart_recovery.bin" and place it in TFTP server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
4. Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Vladimir Kot <vova28rus@gmail.com>
[fixed git commit author and whitespace issues in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The WIZnet WizFi630S board is in the miniPCIe form factor.
SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)
Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1). Then get the
sysupgrade image from a tftp server.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This refreshes the current kernel configuration to remove unneeded
options, add some automatically added ones and reorders them. The normal
build did this automatically, so the builds already used this
configuration.
CONFIG_HW_RANDOM_OMAP is explicitly activated for the cortexa72
subtarget because it has an inside-secure,safexcel-eip76 IP core.
This was done with this command on the cortexa9 subtarget:
make kernel_oldconfig
and this one on the other subtargets:
make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds a ChromiumOS 3.18 patch [0] that fixes memory
allocation issues under memory pressure by keeping track
of missed allocs and rectify the omission at a later date.
It also adds ethtool counters for memory allocation
failures accounting so this can be verified.
[0] <d4e1e4ce68>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Some broken ISPs (e.g. Comcast) send DHCPv6 packets with hop limit=0.
This trips up the TTL=0 check in the PPE if enabled.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
COMFAST CF-E5/E7 is a outdoor 4G LTE AP with PoE support, based on
Qualcomm/Atheros QCA9531.
Short specification:
2x 10/100 Mbps Ethernet, with 24v PoE support
64 MB of RAM (DDR2)
16 MB of FLASH (SPI)
2T2R 2.4 GHz, 802.11b/g/n
built-in 1x 3 dBi antennas
output power (max): 80 mW (19 dBm)
Qucetel EC20 LTE MODULE(1x external detachable antenna)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[commit subject fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds support for TP-Link TL-WR710N v1 router.
CPU: Atheros AR9331 400MHz
RAM: 32MB
FLASH: 8MiB
PORTS: 1 Port 100/10 LAN (connected to a switch), 1 Port 100/10 WAN
WiFi: Atheros AR9331 1x2:1 bgn
USB: ChipIdea HDRC USB2.0
LED: SYS
BTN: Reset
Sysupgrade from `ar71xx` works without glitches.
Network interfaces assigned for LAN and WAN ports are `eth1` and `eth0`
respectively, what's consistent with `ar71xx` target. Wireless radio
path is automatically upgraded from `platform/ar933x_wmac` to
`platform/ahb/18100000.wmac`.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
This adds support for the Chinese version of TL-WR941N v7.
It uses QCA9558+AR8236 while the international version
uses TP9343 instead.
Specification:
- SoC: Qualcomm Atheros QCA9558
- Flash: 4 MB
- RAM: 64 MB
- Ethernet: Atheros AR8236 with 5 FE ports
Flash instruction:
Upload the generated factory firmware on web interface.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This allows users to specify a shorter mib poll interval so that the
swconfig leds could behave normal with current get_port_stats()
implementation.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This applies to ar8216 and ar8236. QCA's newer U-boot will enable
the switch mdio master for FE switches which makes phy inaccessible
from CPU mdio. (e.g. on TP-Link TL-WR941N v7 Chinese version which
uses QCA9558+AR8236.) For these devices PHY probing is broken and
mdio device probing is a must. We also need to disable switch mdio
master in driver for later PHY initialization.
Do a soft reset during hw_init so that mdio master can be disabled
and expose PHYs to CPU mdio for later PHY accessing.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
ar8xxx_mib_capture will update mib counters for all ports. Current
code only update one port at a time and the data for other ports
are lost.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Partially reverts commit eff3549c58.
AR7240 and AR9341 have buggy hardware switch LED trigger. The AR7240
one doesn't blink and the blinking of port0/port5 is reversed on
AR9341 if we swap PHY0 and PHY4. (Only blinking is reversed, which
means LED for PHY0 will lit when PHY0 is link up and will blink when
PHY4 has active link and vice versa.) On these two chips a software
swconfig LED trigger is required.
This commit adds swconfig port stats back but:
1. move checking of mib_t/rxb_id into ar8xxx_chip since we can't
distinguish ar7240sw and ar8216 using only chip id.
2. don't update mib counter in get_port_stat. This function is called
every 0.01s and this capturing procedure will take up a lot of CPU.
We already have a mib_work_func updating mib counters every 2s so
return the saved counter instead of fetching new data. The blinking
rate will be weird but it should solve the previously mentioned CPU
time problem.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This builtin switch is a bugless ar8216 with different mib counters
and gigabit cpu port.
Atheros uses the same device ID and it's impossible to distinguish
the standalone one and the builtin one. So we add support to mdio
device probe only.
This switch doesn't have buggy vlan tag so it's not needed to enable
atheros header. This commit changed ar8216_setup_port so that it can
be reused for this switch.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Atheros FE switches have a builtin mdio master available for PHY
accessing and on ar724x/ar933x builtin switches this mdio master
is the only way of accessing PHYs.
After this patch if there is phy_read/phy_write method available
in ar8xxx_chip we register a separated mdio bus for accessing PHYs.
Still adds support for mdio device probing only since this isn't
needed for those switches registered using PHY probing.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
ar8229 is the builtin switch in ar934x and later chips. There is
also a standalone version available and their registers/functions
are the same.
This commit added support for the builtin ar8229. The only thing
missing for standalone ar8229 should be phy modes. Since I don't
have a router using that, this commit doesn't add support for
other phy modes.
Only add its support for mdio-device probing method because the
current PHY probing can't return 1G speed when it's a FE switch.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
ar8xxx_id_chip is used to determine current ar8xxx_chip using switch
id and this isn't needed during mdiodev probing.
Move it out of ar8xxx_probe_switch so that we can skip it.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
for mdio-device probing we still need to read chip id but ar8xxx_chip
can be determined using drvdata. We can't distinguish the buggy
standalone ar8216 and the builtin ar8216 in ar724x/ar933x using chip
id.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The following patches are dropped because they are merged upstream:
-0001-tty-serial-drop-QCA-pecific-SoC-symbols.patch
-0006-usb-drop-deprecated-symbols.patch
-0009-MIPS-ath79-add-lots-of-missing-registers.patch
-0010-MIPS-ath79-add-support-for-QCA953x-QCA956x-TP9343.patch
-0014-MIPS-ath79-finetune-cpu-overrides.patch
-0015-MIPS-ath79-enable-uart-during-early_prink.patch
-0016-MIPS-ath79-get-PCIe-controller-out-of-reset.patch
This patch is dropped due to the introduction of spi-mem framework:
-461-spi-ath79-add-fast-flash-read.patch
Thank to Michael Marley @mamarley for his work on this patch:
-910-unaligned_access_hacks.patch
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[synchronized kernel config with make kernel_oldconfig]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
linux 4.19 doesn't accept a NULL device for these functions.
It also complains that the device struct in net_device doesn't have
a dma_mask set.
Pass the device struct from platform_device for these functions.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Kernel newer than 4.15 dropped "data" field and used from_timer
to cast out the parent struct pointer for current timer.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The DIR-510L Wireless Router are based on the MT7620A SoC.
Specification:
-MediaTek MT7620A (580 Mhz)
-128 MB of RAM
-16 MB of FLASH
-802.11bgn radio
-1x 10/100 Mbps Ethernet
-2x internal, non-detachable antennas
-UART (J3) header on PCB (57600 8n1)
-1x bi-color LED (GPIO-controlled), 2x button
-JBOOT bootloader
Known issues:
-Ethernet port is used as LAN
-No communication with charger IC. (uart bitbang needed)
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed whitespace issue in 10-rt2x00-eeprom]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Some boards with JBOOT have partiton between bootloader
and kernel image. This patch add possibility to change kernel
partition start address.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
clk_get_rate returns the current clock rate in Hz for a clock source so
if we divide it by 1M, then we get frequency in MHz and not kHz.
Signed-off-by: Qin Wei <support@vocore.io>
[added missing commit message, and fixed author with SoB from PR message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The PCIe DWC host controller is now using MSI
(Message-signaled-interrupts) by default.
While ath9k itself does support MSI here, a lot of wlan adapters do not.
Avoid non-functioning cards by simply continue to disable MSI for now.
This can be done by appending "pci=nomsi" to the boot cmdline.
Also an extra fix needs to be backported which avoids MSI initialization
which prevented legacy IRQ's init from taking over.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The DWC host controller symbols are now depending on a few others
Fixes: ca1b93f038 ("imx6: add support for kernel 4.19")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware
almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation
AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi
indicators, the fifth LED is used as an ethernet link/activity indicator.
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
WLAN: QCA988X
Ports: 1x GbE
Flashing procedure is identical to the NanoStation AC loco and can be performed
either via serial or the factory firmware upgrade.
Serial flashing:
1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Flashing through factory firmware:
1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version.
2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot
Thanks to @cybermaus for testing!
Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com>
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
The Mikrotik RouterBOARD SXT 2nD r3 is an outdoor WiFi AP / CPE
with a single 2.4 GHz radio and a 100 Mbps Ethernet port.
The device similar to the SXT 2nD r2, but it has SPI NOR flash instead
of NAND flash.
Hardware
--------
CPU: Atheros AR9344 (600 MHz)
RAM: 64 MiB
FLASH: 16 MiB SPI NOR W25Q128
ETH: 1x 100 Mbps Atheros AG71xx
WiFi: 2T2R 802.11b/g/n (ath9k)
Power: Passive PoE 8-30 V
Installation instructions:
1. Boot openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf using a
DHCP+TFTP server.
2. Erase the "firmware" partition using the mtd command. This should
no longer be required once this patch is merged.
3. Use sysupgrade to install to flash. The file
openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin
should be used.
Signed-off-by: Xavier Douville <github@douville.org>
ath10k_pci driver crashes once loaded and causes boot loops on this
device as 5GHz radio QCA9880-AR1A shipped with this router is broken.
It's not possible to fix this problem in software, miniPCIe radio has to
be replaced.
We could've probably fixed crashing of the ath10k driver by reverting
following upstream commit:
commit 1a7fecb766c83dace747f42b25bbb544b00a0163
Author: Michal Kazior <michal.kazior@tieto.com>
Date: Sat Jan 24 12:14:48 2015 +0200
ath10k: reset chip before reading chip_id in probe
but it's not worth the effort as it wouldn't make that 5GHz radio usable
anyway. So it seems more convenient to just remove the crashing driver
and provide bootable images, as I believe, that a router that is working
but degraded is better than a router that will not work.
For details please see discussions in PR[1] and in FS#1743[2].
1. https://github.com/openwrt/openwrt/pull/1349
2. https://bugs.openwrt.org/index.php?do=details&task_id=1743
Signed-off-by: Aubrey McIntosh, PhD <aubrey.mcintosh@utexas.edu>
[subject and commit message tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The port labled as "LAN" is eth1.
That's different from the -lite variant,
where the only existing port eth0 is used as LAN
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.
This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.
This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Rosen Penev <rosenp@gmail.com>
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware
--------
CPU: Qualcomm IPQ4018
RAM: 256M
FLASH: 32M SPI NOR W25Q256
ETH: QCA8075
WiFi2: IPQ4018 2T2R 2SS b/g/n
WiFi5: IPQ4018 2T2R 2SS n/ac
LED: - Power amber
- LAN1(PoE) green
- LAN2 green
- Wi-Fi 2.4GHz green
- Wi-Fi 5GHz green
BTN: - WPS
UART: 115200n8 3.3V J1
VCC(1) - GND(2) - TX(3) - RX(4)
Added basic support to get the device up and running for a sysupgrade
image only.
There is currently no way back to factory firmware, so this is a one-way
street to OpenWRT.
Install from factory condition is convoluted, and may brick your device:
1) Enable SSH and disable the CLI on the factory device from the web user
interface (Management->Advanced)
2) Reboot the device
3) Override the default, limited SSH shell:
a) Get into the ssh shell:
ssh admin@192.168.1.1 /bin/sh --login
b) Change the dropbear script to disable the limited shell. At the
empty command prompt type:
sed -i '/login_ssh/s/^/#/g’ dropbear
/etc/init.d/dropbear restart
exit
4) ssh in to a (now-) normal OpenWRT SSH session
5) Flash your built image
a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
admin@192.168.1.1:/tmp/
b) ssh admin@192.168.1.1
c) sysupgrade -n
/tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
6) After flash completes (it may say "Upgrade failed" followed by
"Upgrade completed") and device reboots, log in to newly flashed
system. Note you will now need to ssh as root rather than admin.
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
[whitespace fixes, reordered partitions, removed rng node from 4.14,
fixed 901-arm-boot-add-dts-files.patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Eric has reported on OpenWrt's bug tracking system[1], that he's not
able to use USB devices on his WNDR3400v2 device after the boot, until
he turns on GPIO #21 manually through sysfs.
1. https://bugs.openwrt.org/index.php?do=details&task_id=2170
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Andrey has reported on OpenWrt's bug tracking system[1], that he
currently can't use ar93xx_uart as pure serial UART without console
(CONFIG_SERIAL_8250_CONSOLE and CONFIG_SERIAL_AR933X_CONSOLE undefined),
because compilation ends with following error:
ar933x_uart.c: In function 'ar933x_uart_console_write':
ar933x_uart.c:550:14: error: 'struct uart_port' has no
member named 'sysrq'
1. https://bugs.openwrt.org/index.php?do=details&task_id=2152
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Building tda1997x fails now unless V4L2_FWNODE is selected:
drivers/media/i2c/tda1997x.o: in function `tda1997x_parse_dt'
undefined reference to `v4l2_fwnode_endpoint_parse'
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This patch increases available space from 20MB to 86MB.
Netgrear OEM firmware contains a 'netgear' partition followed 'ubi',
which can be used in openwrt for larger ubi space. (similar to
Netgear R7800).
original author (notmyrealhandle) tested this on R7500v2 and point that
OEM firmware can auto rebuild this partition (if used by openwrt).
Author: notmyrealhandle<22336358+notmyrealhandle@users.noreply.github.com>
Signed-off-by: Wang Xin-yu (王昕宇) <comicfans44@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [minor touch-ups]
Support for the Nanostation M (XW) was added in 40530c8eb with board
name "nanostation-m-xw". The current image for the "Nanostation M"
uses "nano-m" as the board name.
This commit renames it to the full product name as it's used by all
other boards. The legacy boardname of the ar71xx target is added
via SUPPORTED_DEVICES to ease switching to ath79 target.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[touch-ups on the commit message, removed subject remains]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
To be able to configure pwms the pwm driver needs to know the number off
cells in the "pwms" property. For this platform this is 2.
Signed-off-by: Micke Prag <micke.prag@telldus.se>
jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.
Specification
SoC: Atheros AR7161
RAM: 64 MB DDR
Flash: 16 MB SPI NOR
Ethernet: 2x 10/100/1000 Mbps AR8316
LAN (CN11), WAN/PoE (CN6 - close to power barrel
connector, 48 V)
MiniPCI: 2x
LEDS: 4x, which 3 are GPIO controlled
Buttons: 2x GPIO controlled
Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial: 1x (only RX and TX are wired)
baud: 115200, parity: none, flow control: none
Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.
Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
process and enter RedBoot (bootloader) command line by pressing
Ctrl+C,
4. Enter following commands (replace variable accordingly),
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_adress>
(confirm storing the value by inputting y and pressing Enter)
reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.
Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_address>
(confirm storing the value by inputting y and pressing Enter)
ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
load -r -b 0x80060000 <openwrt_initramfs_image_name>
exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
is ready for configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
In PR [1] introducing initial support for Ubiquiti RouterStation boards,
Mathias Kresin suggested to replace the combined sysupgrade image with
tarball generated by sysupgrade-tar.sh. This would simplify deployment
of sysupgrade as the kernel size (needed to update FIS partition) could
be simply calculated on the fly instead of reading value from combined
image header. Unfortunately this would break sysupgrade compatibility
between ar71xx image and ath79 image. Therefore this commit creates
migration path to use new sysuprade image, it adds code to accept both
of them at this moment. The plan is to keep it until new stable version
is released. Then the image recipe should be changed to new format and
compatibility code for old image removed.
1. https://github.com/openwrt/openwrt/pull/1237
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
When upgrading from ar71xx target images to ath79 based ones, the
integrated wireless interface changes its sysfs path. Therefore the
previous enabled wireless interface will be disabled, which can cause
false complains about it not working. This commit adds hotplug event
which migrates to new path and will keep the wrireless interface
enabled after upgrade.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Align the LEDs deffinition with MACH file present in ar71xx target which
has the correct LED functions and colors adescription.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
It is unused by default and upstream is trying to remove it as it has
negative effects when the driver is under load. Upstream explanation:
netpoll: avoid capture effects for NAPI drivers
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC).
This capture, showing one ksoftirqd eating all cycles
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller() :
Most NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev(
uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Although the amount of data read here is smaller than for the
caldata, there still might be some speed gain compared to reading
bytewise. And there is no harm ...
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.
This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.
This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.
Speed comparison @ TP-Link TL-WDR4300 (just manually) results
in a time reduction by three orders of magnitude (99.9 %).
> time dd if=/dev/mtd3 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096
4096+0 records in
4096+0 records out
real 0m 15.85s
user 0m 0.06s
sys 0m 13.28s
> time dd if=/dev/mtd3 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes
1+0 records in
1+0 records out
real 0m 0.02s
user 0m 0.00s
sys 0m 0.02s
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.
This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.
This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.
Speed comparison @ UBNT AC-Mesh (just manually) results
in a time reduction by three orders of magnitude (99.9 %).
> time dd if=/dev/mtd6 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096
4096+0 records in
4096+0 records out
real 0m 16.84s
user 0m 0.07s
sys 0m 13.54s
> time dd if=/dev/mtd6 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes
1+0 records in
1+0 records out
real 0m 0.02s
user 0m 0.00s
sys 0m 0.02s
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Rosen Penev <rosenp@gmail.com>
We currently generate a kernel that boots from the harddrive
in the DIR-685. That's not how we usually do things, so
let's augment it to boot from flash and mount the rootfs
using squashfs and JFFS2 like everyone else.
Partition splitting only work when the partitions are
inside of a "partitions" node which is why we have a patch
like this (submitted upstream).
Another patch drops the rootfs arguments and renames the
firmware partition while adding the compatible "wrg"
to it so the WRGG parser will kick in.
Factory image was tested by bravely reflashing the DIR-685
from stock firmware using the web UI and the serial console
boot loader.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WRGG images exist in both big and little endian variants,
as can be seen from the image generator in
tools/firmware-utils/src/mkwrggimg.c, you either pass
the "-b" flag or not. The D-Link DIR-685 is using little
endian images so we need to support splitting these.
Detect endianness like this: if the kernel entity size
gets silly big (bigger than the flash memory) we are
probably using the wrong endianness.
Example: my kernel of 0x0067ff64 was switched around by
wrong endianness and detected as 0x64ff67a0 (the actual
size in swapped endianness + header 0xa0).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band
wireless router.
Specification
SoC: Qualcomm Atheros QCA9558
RAM: 256 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 5x 10/100/1000 Mbps QCA8337N
USB: 1x 2.0
LEDS: 4x GPIO controlled
Buttons: 2x GPIO controlled
UART: 4 pin header, starting count from white triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Tools > Firmware,
4. Select OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
is ready for configuration.
Alternative installation
1. Prepare TFTP server with OpenWrt sysupgrade image,
2. Connect to one of LAN (yellow) ethernet ports,
3. Connect to UART port (leaving out VCC pin!),
4. Power on router,
5. When asked to enter a number 1 or 3 hit 2, this will select flashing
image from TFTP server option,
6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8),
then router ip (default is 192.168.99.9) and for last, image name
downloaded from TFTP server (default is uImageESR1200_1750),
7. After providing all information U-Boot will start flashing the image,
You can observe progress on console, it'll take few minutes and when
the Power LED will stop blinking, router is ready for configuration.
Additional information
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: aigo3d0a0tdagr
useful for creating backup of original firmware.
When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep
the old configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH: Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED: - Connect green/blue/red
- Power green
BTN: WPS/Connect
UART: 115200n8 3.3V
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ3000.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz3000.bin uboot0
> mtd write /path/to/uboot-fritz3000.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
AVM devices based on Qualcomm IPQ40xx do not store sector health
information in the OOB area. Make this check optional to support this
platform.
Signed-off-by: David Bauer <mail@david-bauer.net>
AR300M-Lite is single-Ethernet variant of the AR300M series
Its eth0 would otherwise be assigned to the WAN interface
making it unreachable firstboot or failsafe.
Installation instructions from OEM (OpenWrt variant):
* Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI),
* Do not preserve settings
* Access rebooted device via Ethernet at OpenWrt default address
Add previously missing LED defaults for all three variants;
-nand, -nor, -lite to the definitions in 01_leds
Non-lite variants thanks to Andreas Ziegler
https://patchwork.ozlabs.org/patch/1049396/
Runtime-tested: GL.iNet AR300M-Lite
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Hardware:
CPU: MediaTek MT7621AT (2x880MHz)
RAM: 512MB DDR3
FLASH: 256MB NAND
WiFi: 2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI: 5GHz 4x4 MT7615 a/n/ac (Needs driver, See Issues!)
USB: 1x 3.0
ETH: 1x WAN 10/100/1000 3x LAN 10/100/1000
LED: Power/Status
BTN: RESET
UART: 115200 8n1
Partition layout and boot:
Stock Xiaomi firmware has the MTD split into (among others)
- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)
Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.
Note uboot's tftp flash install writes the transferred
image to both kernel partitions.
Installation:
Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.
The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:
nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot
Reverting to stock:
The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.
For this we do the following:
fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot
After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.
Issues:
OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.
See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
Hardware
--------
SOC: QCA9558
RAM: 128M DDR2
Flash: 16MiB SPI-NOR
ETH: QCA8337N: 2x 10/100/1000 PoE and PoE pass-through
WiFi2: QCA9558 (bgn) 2T2R
WiFi5: 2x mPCIE with AR9582 (an) 2T2R
BTN: 1x Reset
GPIO: multiple GPIO on header, PoE passthrough enable
UART: 3.3V 115200 8N1 header on the board
WDG: ATTiny13 watchdog
JTAG: header on the board
USB: 1x connector and 1x header on the board
PoE: 10-32V input in ETH port 1, passthrough in port 2
mPCIE: 2x populated with radios (but replaceable)
OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin
using the web interface or with sysupgrade -n.
Flash from bootloader (in case failsafe does not work)
1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART
header in the board.
2. Connect an ETH cable and configure static ip addres 192.168.1.10/24
3. Turn on the device and stop the bootloader sending any key through the serial
interface.
4. Use a TFTP server to serve <your image>-sysupgrade.bin file.
5. Execute the following commands at the bootloader prompt:
ath> tftp 82000000 <your image>-sysupgrade.bin
ath> erase 0x9f050000 +$filesize
ath> cp.b 0x82000000 0x9f050000 $filesize
ath> bootm 0x9f050000
More docs
* Bootloader https://github.com/librerouterorg/u-boot
* Board details (schematics, gerbers): https://github.com/librerouterorg/board
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
This removes the 'cs-gpios' property from the AVM FRITZ!Box 7530 NAND
controller node. As pointed out by Christian Lamparter, the property is
not needed by the Qualcomm NAND controller driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch fixes a problem that was discovered during DSA
development. On the MR33, the link change events from the
external AR8035-PHY would never make it to the qca8k driver.
The issue turned out to be a misplaced memcpy that was copying
over the zero-initialized irq table, when it should have been
set to PHY_POLL. Hence this patch moves the memcpy after the
array has been initialized.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
PogoPlug Pro comes with AzureWave AW-NE762H PCIe module containing
Ralink's Rt3090 chip supported by the rt2x00 driver.
Install the driver as well as wpad-basic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range
extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros
QCA9558 + QCA9882 + AR8035 platform and is available only on US market.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x 1 Gbps Ethernet (AR8035)
- 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11)
- 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11)
- 2x U.FL connector on PCB
- 2x dual-band PCB antennas
- 1x LED, 2x dual-color LED (all driven by GPIO)
- 3x button (app config, led, reset)
- 1x mechanical on/off slide switch
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x JTAG (8-pin, 1.27 mm pitch) header on PCB
Flash instruction:
Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254,
default credentials: admin/admin).
Warning:
This device does not include any kind of recovery mechanism in U-Boot.
Vendor firmware access:
You can access vendor firmware over serial (RX line requires jumper
resistor in R306 place, near XTAL) with: root/sohoadmin credentials.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on
MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem.
Specification:
- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 1x detachable antenna (modem main)
- 1x internal antenna (modem div)
- 1x GPS passive antenna (optional)
- 5x LED (all driven by GPIO)
- 1x button (reset)
- UART (4-pin, 2.54 mm pitch) header on PCB
Other:
Default SIM slot is selected at an early stage by U-Boot, based on
'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2
(micro). U-Boot also resets the modem, using #PERST signal, before
starting kernel.
Flash instruction:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the LAN LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This disables PL010 and 8250 serial support for this platform
as both drivers are not used: the debug UART is PL011 and the
application UARTs use a dedicated MXS specific driver.
The kernel size reduction is neglectable, but it also removes
the non-working (confusing) /dev/ttyS0 and /dev/ttyS1 devices
in a running system (which generate errors when trying to use):
root@OpenWrt:~# echo "hello world" > /dev/ttyS0
ash: write error: I/O error
root@OpenWrt:~#
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Move PCIe controller outside down to SoC level to avoid resource
mapping problems.
Also add more detailed error handling when mapping registers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Joachim Fünfer
David Bauer
Rosy Song
Petr Štetiar
Hauke Mehrtens
Koen Vandeputte
Felix Fietkau
Yousong Zhou
Lucian Cristian
Christian Lamparter
Eike Feldmann
Pawel Dembicki
INAGAKI Hiroshi
Sven Roederer
Daniel Golle
Daniel Gimpelevich
Adrian Schmutzler
Christian Mauderer
Markus Scheck
Kip Porterfield
Chuanhong Guo
Tomasz Maciej Nowak
Zhao Yu
Daniel Engberg
Luis Araneda
Rafał Miłecki
Mario Schroen
Robert Marko
Michael Pratt
Rosen Penev
Vladimir Kot
Tobias Welz
Hauke Mehrtens
Ding Tengfei
Marcin Jurkowski
Qin Wei
Tobias Schramm
Xavier Douville
Aubrey McIntosh, PhD
Andreas Ziegler
Ozgur Can Leonard
Steve Glennon
Evgeniy Didin
Wang Xin-yu (王昕宇)
Micke Prag
Martin Schiller
kbuild test robot
Linus Walleij
Marius Genheimer
Jeff Kletsky
Chen Minqiang
Santiago Piccinini
Piotr Dymacz
Michael Heimpold