1a71f07d00
generate uboot environment data in target
...
With this patch it is possible to generate uboot environment config file
inside lantiq target. Currently it is only supporting GIGASX76X board.
uboot environment config is used by fw_printenv fw_setenv tools.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 30537
2012-02-14 19:07:11 +00:00
7416a5f0aa
fix compile error in previous commit
...
SVN-Revision: 30534
2012-02-14 19:07:05 +00:00
cd1a204365
Support booting the Speedport W502V using BRN-BOOT.
...
While the disadvantage is less available flash space, it's easy and
safe to flash without opening the device.
Going back to the original firmware is also possible.
This patch add two firmware utilities, mkbrncmdline and mkbrnboot.
mkbrncmdline patches the uncompressed kernel so the registeres a0 to
a3 are initialized and the memory size is passed in.
mkbrnboot takes the lzma compressed kernel and squashfs images and
creates a firmware image that can be flashed using the BRN-BOOT
recovery kernel, which is booted by holding both buttons when
powering up the device and will listen on http://192.168.2.1 .
The firmware file from bin/lantiq/ to use is
openwrt-lantiq-danube-ARV4525PW-BRNDTW502-brnImage
The BRN-BOOT recovery kernel does size-check the image, so if it's
too big to fit into flash it will complain accordingly.
A second patch is needed to make the wired network interface work
since there is no u-boot to pre-initialise it.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 30532
2012-02-14 17:48:04 +00:00
02a01a16c7
ramips: extract eeprom for the PCIe wlan module on the RT-N56U
...
SVN-Revision: 30529
2012-02-14 17:32:45 +00:00
43d1a2c3ab
ramips: rt3883: enable PCI on the RT-N56U board
...
SVN-Revision: 30528
2012-02-14 17:32:44 +00:00
784be92e39
ramips: rt3883: add PCI support
...
SVN-Revision: 30527
2012-02-14 17:32:42 +00:00
10f00dc48b
ramips: rt3883: sync 2.6.39 config
...
SVN-Revision: 30526
2012-02-14 17:32:41 +00:00
ed79921fe5
ramips: use SoC specific irq.h
...
SVN-Revision: 30525
2012-02-14 17:32:40 +00:00
0b07769898
fixes irq locking in ethernet driver
...
SVN-Revision: 30522
2012-02-14 15:05:58 +00:00
55bf39e98c
fixes gpio_export patch
...
SVN-Revision: 30521
2012-02-14 15:05:57 +00:00
976d3eb854
add annex selection support to ltq_dsl package
...
SVN-Revision: 30518
2012-02-14 15:05:49 +00:00
9a0e17857e
ar71xx: add profile and build image for the TP-Link TL-WR842N/ND v1 boards
...
SVN-Revision: 30508
2012-02-13 17:11:58 +00:00
1c57a22aae
ar71xx: add model detection for TL-WR842N/ND
...
SVN-Revision: 30507
2012-02-13 17:11:57 +00:00
e16916480d
update to 3.2
...
SVN-Revision: 30503
2012-02-13 16:05:30 +00:00
7bed2e2225
fix titan gpio register size
...
SVN-Revision: 30502
2012-02-13 16:05:27 +00:00
8d5dfa75e6
ramips: rt3883: update package list in the default profile
...
SVN-Revision: 30499
2012-02-13 15:18:05 +00:00
99c019fb0d
ramips: add preliminary support for the Asus RT-N56U board
...
SVN-Revision: 30498
2012-02-13 15:18:04 +00:00
97e641a0e6
ramips: raeth: enable MDIO code for RT3883
...
SVN-Revision: 30497
2012-02-13 15:18:03 +00:00
e532fa5fd4
ramips: add preliminary support for the RT3662/RT3883 SoCs
...
SVN-Revision: 30495
2012-02-13 15:17:59 +00:00
4a0dc3a32a
add support for 3.2
...
SVN-Revision: 30492
2012-02-13 12:36:34 +00:00
30408f1cc4
brcm47xx: deactivate CONFIG_NO_HZ as it seams not to be needed.
...
SVN-Revision: 30488
2012-02-12 22:41:20 +00:00
e7bd7f7e85
brcm47xx: activate config bug to show warnings
...
SVN-Revision: 30487
2012-02-12 22:40:01 +00:00
22ec8b4839
ramips: use GENERIC_{4,8}M image template for WR5123GN
...
SVN-Revision: 30483
2012-02-12 18:04:47 +00:00
b7f129e19b
ramips: rt305x: pass MTD partition map to the ALL0256N via cmdline
...
SVN-Revision: 30482
2012-02-12 18:04:46 +00:00
fa21aef5ab
brcm47xx: refresh patches
...
SVN-Revision: 30481
2012-02-12 16:45:27 +00:00
838c363886
brcm47xx: update usb driver for brcm47xx.
...
SVN-Revision: 30480
2012-02-12 16:38:10 +00:00
a287c60a61
ramips: add initial support for 3.2
...
SVN-Revision: 30476
2012-02-12 12:52:14 +00:00
388013b0ce
ramips: include 'linux/module.h' in the ramips_spi driver
...
SVN-Revision: 30475
2012-02-12 12:52:13 +00:00
faae4235c4
ramips: rt288x: remove per-board physmap_flash_data instances
...
SVN-Revision: 30474
2012-02-12 12:52:12 +00:00
3502e2b93f
ramips: rt305x: remove per-board physmap_flash_data instances
...
SVN-Revision: 30473
2012-02-12 12:52:10 +00:00
143e861708
enable another l2 cache errate on newer kernels
...
SVN-Revision: 30472
2012-02-12 11:22:08 +00:00
3a11dcdaa8
ramips: load gpio-polled keys module
...
SVN-Revision: 30463
2012-02-11 20:37:34 +00:00
323ece9474
ramips: remove yet another CONFIG_MTD_PARTITION ifdef
...
SVN-Revision: 30462
2012-02-11 19:37:11 +00:00
32b9e8c750
ramips: use gpio-keys-polled instead of gpio-buttons
...
SVN-Revision: 30461
2012-02-11 19:37:06 +00:00
8ce80f7454
add some missing symbols
...
SVN-Revision: 30460
2012-02-11 18:38:28 +00:00
80b40497de
ramips: add MIPS platform file
...
SVN-Revision: 30459
2012-02-11 18:16:11 +00:00
80a535ba58
generic/2.6.39: refresh patches
...
SVN-Revision: 30458
2012-02-11 18:16:08 +00:00
440a7fbc3b
refresh patches to -rc3
...
SVN-Revision: 30456
2012-02-11 17:43:06 +00:00
4e1b870f3e
ramips: add MDIO bus support for RT288X
...
SVN-Revision: 30455
2012-02-11 16:49:56 +00:00
0ace4636db
rename 3.1 patches directory as it will be used for newer kernels as well
...
SVN-Revision: 30454
2012-02-11 15:59:23 +00:00
1fb5ff4e04
rename 2.6.39 patches directory
...
SVN-Revision: 30453
2012-02-11 15:58:14 +00:00
34a9ccf544
ramips: fix Belkin F5D8235-v2 VLAN setup
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 30452
2012-02-11 15:31:18 +00:00
8916c02b47
ramips: raeth: make debugging messages configurable
...
SVN-Revision: 30450
2012-02-11 15:12:10 +00:00
aac3ad4c0e
ramips: raeth: use device pointer in DMA API calls
...
SVN-Revision: 30449
2012-02-11 15:12:08 +00:00
1fd8724e94
ramips: raeth: add netdev pointer to private structure
...
SVN-Revision: 30448
2012-02-11 15:12:06 +00:00
c6fa11d00f
ramips: raeth: cleanup DMA API usage in ramips_eth_hard_start_xmit
...
SVN-Revision: 30447
2012-02-11 15:12:05 +00:00
2d055f130e
ramips: raeth: unmap rx DMA address in ramips_cleanup_dma
...
SVN-Revision: 30446
2012-02-11 15:12:04 +00:00
7bd7ddcf4e
ramips: raeth: add rx_dma array to store the DMA address of the rx packets
...
SVN-Revision: 30445
2012-02-11 15:12:02 +00:00
647af823d9
ramips: raeth: use dma_addr_t for the descriptors
...
SVN-Revision: 30444
2012-02-11 15:12:01 +00:00
df5892d1f1
ramips: raeth: unmap DMA memory when a packet is received
...
SVN-Revision: 30443
2012-02-11 15:11:56 +00:00
617954ca5d
ramips: raeth: add a temporary pktlen variable
...
SVN-Revision: 30442
2012-02-11 15:11:55 +00:00
d1d492eaf9
ramips: raeth: protect macro parameters
...
SVN-Revision: 30441
2012-02-11 15:11:50 +00:00
8250692359
ramips: raeth: indicate dropped packets in stats
...
SVN-Revision: 30440
2012-02-11 15:11:49 +00:00
c67adbbddb
ramips: raeth: use the NUM_TX_DESC for the tx_skb array
...
SVN-Revision: 30439
2012-02-11 15:11:47 +00:00
a2c8789578
ramips: use uncached address in detect_mem_size
...
SVN-Revision: 30438
2012-02-11 15:11:45 +00:00
ba4c9b3a8f
ramips: rt305x: remove CONFIG_MTD_PARTITION ifdefery from machine files
...
SVN-Revision: 30437
2012-02-11 15:11:43 +00:00
f2dd67dc09
ramips: rt288x: remove CONFIG_MTD_PARTITION ifdefery from machine files
...
SVN-Revision: 30436
2012-02-11 15:11:41 +00:00
d6b9f88743
ramips: refresh patches
...
SVN-Revision: 30435
2012-02-11 15:11:40 +00:00
9cde29f1a7
ramips: rt305x: add support for Accton WR6202 / SMCWBR11S-3GN
...
This patch adds support for the Accton WR6202 Mini 3G broadband router.
Full details for this device are available at
http://www.awbnetworks.com/products03.php?Fullkey=19 .
This device is identical to the SMCWBR11S-3GN:
http://www.smc-asia.com/products03.php?Fullkey=210
It's also worth noting that this board has a GPIO line to control the
power to the USB port.
[juhosg:
- fix checkpatch warnings,
- reorder Kconfig entry,
- merge the sysupgrade patch,
- add GPL header]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 30434
2012-02-11 15:11:36 +00:00
59b474732c
ramips: rt305x: merge duplicated mac address setup
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 30433
2012-02-11 15:11:34 +00:00
7298ef2456
ramips: rt305x: add profile for the Belkin f5d8235v2
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 30432
2012-02-11 15:11:32 +00:00
295a154f2f
brcm47xx: print the chip id and rev found by ssb and bcma
...
SVN-Revision: 30428
2012-02-10 22:42:43 +00:00
3708227f96
ar71xx: zero partition parser data in m25p80
...
Ths fixes parsing of RedBoot partitions.
SVN-Revision: 30427
2012-02-10 20:19:06 +00:00
0430194cc3
ramips: fix compiler warning in prom.c
...
SVN-Revision: 30424
2012-02-10 17:38:46 +00:00
4e332227d0
brcm47xx: update bcm5354 support patch
...
SVN-Revision: 30423
2012-02-10 17:22:26 +00:00
6c07149c2d
ar71xx: fix platform description
...
SVN-Revision: 30419
2012-02-10 15:27:49 +00:00
724211aa0d
generic: fix yaffs2 build warnings on 3.3
...
SVN-Revision: 30418
2012-02-10 15:21:43 +00:00
766999085a
ar71xx: ag71xx: add BQL support
...
It will be usable only from linux-3.3.
Based on a patch by Dave Taht <dave.taht@bufferbloat.net>
SVN-Revision: 30417
2012-02-10 14:56:47 +00:00
fc069f030b
ar71xx: add dummy DQL helper functions for 3.2
...
SVN-Revision: 30416
2012-02-10 14:56:44 +00:00
32a18a05f8
ar71xx: add preliminary support for 3.3
...
SVN-Revision: 30410
2012-02-10 11:53:56 +00:00
512df38f5c
ar71xx: disable DDR flush for ethernet on AR934x, it is no longer necessary
...
SVN-Revision: 30409
2012-02-10 11:46:37 +00:00
61f48beadd
ar71xx: fix db120 board detection
...
SVN-Revision: 30408
2012-02-10 11:46:31 +00:00
73b9a8bf9b
ar71xx: allow to build ag71xx w/o PCI support enabled
...
SVN-Revision: 30407
2012-02-10 11:46:10 +00:00
fe0c7aac66
ar71xx: merge 3.2 fixes
...
SVN-Revision: 30406
2012-02-10 08:19:33 +00:00
d72bde99cd
ar71xx: merge files-3.2 to files
...
SVN-Revision: 30405
2012-02-10 08:19:31 +00:00
81b7aaefbe
ar71xx: nuke 2.6.39 support
...
SVN-Revision: 30404
2012-02-10 08:19:28 +00:00
650d777f3d
ar71xx: switch to 3.2.5
...
SVN-Revision: 30403
2012-02-10 08:19:27 +00:00
abeab97efc
ar71xx: refresh 3.2 patches
...
SVN-Revision: 30402
2012-02-10 08:19:25 +00:00
6959317691
kernel: update linux 3.2 to 3.2.5
...
SVN-Revision: 30401
2012-02-10 08:19:23 +00:00
f754063159
ar71xx: 3.2: remove stray semicolons from the PCI fixup patch
...
SVN-Revision: 30400
2012-02-09 21:19:57 +00:00
848dedeb8b
ar71xx: fix ar934x usb reset handling on 3.2
...
SVN-Revision: 30399
2012-02-09 20:39:41 +00:00
31a0451cee
generic: fix kexec build error for MIPS with gcc-4.6-linaro
...
SVN-Revision: 30395
2012-02-09 14:06:44 +00:00
841f0f23b3
generic: 3.3: add missing config symbols
...
SVN-Revision: 30393
2012-02-09 08:07:52 +00:00
098ca08e94
generic: 3.3: fix yaffs2 build error
...
SVN-Revision: 30392
2012-02-09 08:07:50 +00:00
09c45f50d4
ar71xx: 3.2: get rid of an unused variable in ath79_spi.c
...
SVN-Revision: 30391
2012-02-08 20:47:58 +00:00
c126bed503
ar71xx: 3.2: fix AHB clock name in rb4xx_spi
...
SVN-Revision: 30390
2012-02-08 20:47:56 +00:00
32194001ed
generic: fix yaffs2 build error on 3.2
...
SVN-Revision: 30389
2012-02-08 20:47:54 +00:00
fb53d25fa4
add more missing config symbols
...
SVN-Revision: 30386
2012-02-08 17:35:40 +00:00
81f15f5026
ar71xx: add profile and build image for the TEW-673GRU board
...
SVN-Revision: 30377
2012-02-08 16:26:27 +00:00
48e85cd47b
ar71xx: add support for the TRENDNet TEW-673GRU board
...
SVN-Revision: 30376
2012-02-08 16:26:25 +00:00
b91a542247
select GENERIC_ATOMIC64 implementation to fix xfs related build errors
...
SVN-Revision: 30371
2012-02-08 10:34:21 +00:00
bd8683ac93
add audio and display features
...
SVN-Revision: 30370
2012-02-08 10:21:48 +00:00
f35c4a3266
8139cp: backport patches to make driver stable again
...
List of patches that Jo-Philipp groveled out of git.
Redux: defuzzed.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 30366
2012-02-07 21:56:51 +00:00
834be6c1fe
alix2, geos: Adjust CFLAGS
...
Clone of CFLAGS change from r30013 into Geos and Alix platforms.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 30353
2012-02-07 13:00:47 +00:00
e430c864f4
kernel: add a recent upstream commit (post-3.3) to the ssb update patch, required for the next mac80211 update
...
SVN-Revision: 30345
2012-02-07 11:28:06 +00:00
42ec97097e
generic: Enable HPET, HID and AT keyboard support
...
SVN-Revision: 30309
2012-02-05 17:56:04 +00:00
b5ff8b85d6
generic: Add missing and remove unused config symbols
...
SVN-Revision: 30133
2012-02-04 20:45:17 +00:00
778e5d4fa5
brcm63xx: add support for linux 3.3
...
SVN-Revision: 30027
2012-02-04 10:17:27 +00:00
49874a57f1
kernel: fix netfilter layer7 compilation in 3.3
...
SVN-Revision: 30026
2012-02-04 10:17:14 +00:00
d6afe712ab
x86: make alix platform patch apply to 3.3
...
Based on a patch from Philip Prindeville.
While at it, also refresh the patches.
SVN-Revision: 30025
2012-02-03 20:17:00 +00:00
c433bfb571
disable additional PATA drivers in global 3.2 and 3.3 config, remove redundant symbols from alix2 config
...
SVN-Revision: 30024
2012-02-03 19:47:55 +00:00
40867f1b68
x86: trivial -- add missing CONFIG_GEOS symbol to top-level So that builds don't stall in x86 prompting for this symbol. [From Philip Prindeville, via http://patchwork.openwrt.org/patch/1828/ ]
...
SVN-Revision: 30023
2012-02-03 19:21:41 +00:00
79a3fdb9da
geos: backport driver from linux-next to 3.2 and 3.3 The Geos driver is in linux-next and will be out in 3.4. It builds fine against 3.2.2 and 3.3-rc2. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
...
SVN-Revision: 30022
2012-02-03 18:16:27 +00:00
25d605ab0e
net5501: backport drivers from linux-next Backport net5501 platform driver from 3.4. Remove vestiges of old (pre-2.6.30) leds-net5501.c driver. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
...
SVN-Revision: 30021
2012-02-03 18:14:02 +00:00
7a36f3d2ff
x86: move additional oddball PATA drivers These should only be enabled in the generic image, as they bloat all of the other targets. Also add symbols for NET5501, ALIX, and GEOS which were added backported to 3.2 and 3.3. Restore PC speaker to Geos target. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
...
SVN-Revision: 30019
2012-02-03 18:02:57 +00:00
d13c3cd073
net5501: adjust CFLAGS and package selection ( #10893 ) This patches the CFLAGS for Geode LX CPUs for 4.3 and new GGC versions. This creates more compatible code and allowed me to boot my system first time with no troubles. Also, the missing kmod is added in.
...
SVN-Revision: 30013
2012-02-03 14:19:29 +00:00
d9ff9c44ee
ar71xx: add usb on the pb92 board
...
SVN-Revision: 30007
2012-02-03 09:44:51 +00:00
f99bf6517c
x86: add 3.3 generic symbols
...
Copy x86/config-3.2 to x86/config-3.3 and add additional symbols (for 3.3-rc2).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 30002
2012-02-02 21:01:59 +00:00
b6be49429b
alix2: backport platform driver updates from linux-next Add patches to x86/patches-3.2 and x86/patches-3.3 (update will appear in 3.4). [Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1817/ ]
...
SVN-Revision: 30001
2012-02-02 19:26:32 +00:00
7a9e4ffe8e
alix2, geos, net5501: remove kmod-ledtrig-netfilter, its not used by any standard system facility
...
SVN-Revision: 30000
2012-02-02 19:11:52 +00:00
bf8bb9b661
alix2, goes, net5501: clean up default packages Remove packages which are dependencies of other packages Remove packages which are part of the default package list Remove DSL specific packages from net5501 Remove bridge package, we use the busybox applet Replace hostapd with wpad
...
SVN-Revision: 29999
2012-02-02 19:06:22 +00:00
047ba1e12e
alix2, net5501: bump both subtargets to Linux 3.2.2 to align with the rest
...
SVN-Revision: 29998
2012-02-02 19:00:40 +00:00
1ae5715f2e
geos: add missing files from previous commit
...
SVN-Revision: 29997
2012-02-02 18:59:51 +00:00
a1258ccaba
geos: backport Geos driver from linux-next Backport of linux-next driver. Driver adds support for LEDS and S/W button. Add hotplug script for button actions. Add Openwrt system config for LEDS triggers. Add updated kernel .config for 3.2 symbols. [Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1816/ ]
...
SVN-Revision: 29996
2012-02-02 18:58:20 +00:00
415a375eaa
geos: cleanup GPIO driver name In 3.1, the old drivers/char/ entry for the CS5535 GPIO driver went obsolete. Make Geos use a recent kernel and remove this ambiguity. [Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1815/ ]
...
SVN-Revision: 29995
2012-02-02 18:44:35 +00:00
5523eca4e5
net5501: correct net5501 h/w configuration Bump to version 3.2. Simplify and correct kernel config (based on x86/config-3.2). Designate eth0 as wan interface, and bridge eth1/eth2/eth3. Add heartbeat LED trigger. Use correct CS5535 GPIO driver. Use correct USB drivers (OHCI not UHCI). Add MSR and HW clock support. Add GPIO mask definition. Add correct SATA drivers. Add LED triggers. [Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1802/ ]
...
SVN-Revision: 29994
2012-02-02 18:41:10 +00:00
eca9950f63
kernel: add preliminary support for linux 3.3
...
Based on 3.3-rc2
SVN-Revision: 29986
2012-02-02 08:23:54 +00:00
3310df6b52
alix2: correct h/w configuration Bump to version 3.2. Simplify and correct kernel config (based on x86/config-3.2). Drop obsolete CS5535 GPIO driver.
...
[Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1804/ ]
SVN-Revision: 29981
2012-02-01 15:31:23 +00:00
41bd6bd282
ar71xx: fix ethernet LEDs on the WHR-{G301N,HP-G300N,HP-GN} boards
...
SVN-Revision: 29978
2012-01-31 20:49:34 +00:00
c315ce403b
ar71xx: merge DIR-600 A1 and DIR-615 E4 support
...
SVN-Revision: 29976
2012-01-31 18:37:29 +00:00
dd47afc197
ar71xx: fix ethernet LEDs on the DIR-600-A1 board
...
SVN-Revision: 29975
2012-01-31 18:37:24 +00:00
8200f0c61a
ar71xx: unify LED names on D-Link boards
...
SVN-Revision: 29974
2012-01-31 18:37:15 +00:00
faeca86e50
ar71xx: support for D-LINK DIR-615 rev. E4
...
This patch adds support for D-LINK DIR-615 E4 board. It's mostly based
on the existing support for DIR-600 A1, with some changes in the leds
configuration.
It's an updated version of the patch that reliably works on my hw for
about a year (it was built from trunk on Jan 2011). When I decided to
update the firmware and checked for the current support for that device,
I also found previously posted patches by Alexey Loukianov that
mentioned some stability issues. I'm not sure where could be the
difference, the patches are very similar except the wmac led pin number
- I was using 1, and those patches used 17.
[juhosg: add 3.2 support]
Signed-off-by: Vadim Girlin <vadimgirlin@gmail.com>
SVN-Revision: 29973
2012-01-31 18:37:09 +00:00
97e4ddd012
ar71xx: add support for TP-Link TL-MR11U
...
Adds support for TL-MR11U, a portable router with very similar
hardware to the TL-WR703N and TL-MR3020, but with an onboard
2000mAh battery.
Tested, working:
All interfaces (Ethernet, 802.11n, USB)
WPS & Reset switches (Power appears to be a hardware slider)
Ethernet, Wifi, 3G LEDs (Power & charging LEDs hardware controlled)
Sysupgrade
[juhosg: fix indentations to use TABs instead of spaces, fix 3.2 patch
breakage]
Signed-off-by: Simon Taylor <simon.taylor.uk@gmail.com>
SVN-Revision: 29972
2012-01-31 18:37:01 +00:00
8766f32b8c
ar71xx: compress kernel binaries in Image/Prepare stage
...
The lzma compressed kernel is used by one of the loaders.
SVN-Revision: 29971
2012-01-31 18:36:54 +00:00
d5d37febb4
ar71xx: use dynamically allocated partitions in wrt160nl_part
...
SVN-Revision: 29970
2012-01-31 18:36:51 +00:00
44ed690cb3
ramips: change vlan_config for the ALFA W502U board
...
This change moves the WAN port into a separate VLAN.
SVN-Revision: 29969
2012-01-31 18:34:10 +00:00
b3568b10c2
kernel: update linux 3.2 to 3.2.2
...
SVN-Revision: 29967
2012-01-31 09:44:00 +00:00
1015fab0d7
kernel: update linux 3.1 to 3.1.10
...
SVN-Revision: 29966
2012-01-31 09:43:57 +00:00
e67f4477bb
kernel: update linux 3.0 to 3.0.18
...
SVN-Revision: 29965
2012-01-31 09:43:53 +00:00
882eddbf92
build 96348R images
...
SVN-Revision: 29960
2012-01-30 21:12:32 +00:00
0700644b16
remove support for 2.6.39
...
SVN-Revision: 29959
2012-01-30 21:12:28 +00:00
038fc8eac3
bump to 3.0.17
...
SVN-Revision: 29958
2012-01-30 21:12:25 +00:00
8100658a30
add missing config symbols
...
Thanks KanjiMonster
SVN-Revision: 29955
2012-01-30 10:53:20 +00:00
0501ea063b
fix gpiommc build failure with 3.2
...
SVN-Revision: 29954
2012-01-30 10:53:16 +00:00
55b5e15bff
create a config-3.2 for upcoming changes, rebase config-default to 2.6.39
...
SVN-Revision: 29953
2012-01-30 02:13:37 +00:00
8c4813b75e
add default and Sim.One profiles
...
SVN-Revision: 29942
2012-01-29 15:00:36 +00:00
0bb50678de
add 3.2 support
...
SVN-Revision: 29941
2012-01-29 15:00:33 +00:00
e82f06639e
add another 3.2 framebuffer symbol
...
SVN-Revision: 29940
2012-01-29 15:00:29 +00:00
ad808cf7e6
add support for 3.2 kernel
...
SVN-Revision: 29939
2012-01-29 15:00:25 +00:00
eeb00634a7
add support for the Atheros AP113 reference board
...
This reference board is equipped with:
- AR7242 SoC
- AR9580 on-board Wi-Fi
- AR8316 switch
SVN-Revision: 29935
2012-01-28 13:19:49 +00:00
405a0f3905
refresh 3.2 patches
...
SVN-Revision: 29934
2012-01-28 13:19:43 +00:00
d1c07b3657
brcm47xx: add fix for cardbus host controller
...
These devices have two devices on the bus, the host controller itself and the device.
SVN-Revision: 29923
2012-01-27 20:10:51 +00:00
b9b768b8d3
ar71xx: use 64k block size for WZR-HP-AG300H
...
SVN-Revision: 29917
2012-01-27 10:42:41 +00:00
ac8116739a
ar71xx: fix sysupgrade image building of atheros boards after r29899
...
SVN-Revision: 29916
2012-01-27 07:51:09 +00:00
013fe76b36
ar71xx: create the temporary directory before building initramfs images
...
Thanks to Florian for reporting.
SVN-Revision: 29915
2012-01-26 21:28:34 +00:00
a5538a18d4
ar71xx: create a profile and build images for Compex WPE72
...
[juhosg: remove ath9k from the the profile package list, build WPE72
image with the Default profile as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 29914
2012-01-26 17:01:44 +00:00
e1e84badaa
ar71xx: add support for Compex WPE72/WPE72NX
...
This patch adds support for Compex WPE72 bare board and Compex WPE72NX
Indoor Access Point.
[juhosg: add support to 3.2 as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 29912
2012-01-26 17:01:41 +00:00
1c4f6b4308
generic: add WPE72 ID to myloader.h
...
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 29911
2012-01-26 17:01:38 +00:00
b3fdd931d1
ramips: add support for Sitecom WL-341v3 and other Sercomm IP1006RRv2 boards
...
This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 29910
2012-01-26 10:44:23 +00:00
038d4e0d77
ar71xx: TL-MR3020: fix board detection, fix missing mandatory package and modify LED behaviour
...
This patch fixes the board detection of the TL-MR3020.
The LED behaviour has also been modified:
* The WPS LED is the diag LED now.
* A netdev trigger for the LAN LED has been added.
The profile of the TL-MR3020 has been updated because the needed package
"kmod-ledtrig-usbdev" was missing which resulted in a non-working usbdev
trigger for the 3G/USB LED.
[juhosg: the board name changes has been removed, and the kernel files
has been changed instead.]
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29905
2012-01-25 07:44:45 +00:00
c11ac55b29
ar71xx: TL-MR3020: fix GPIO polarity for button and switch
...
This patch fixes the GPIO polarity for the button and the sliding
switch. The buttons are not active low. "Pressed" and "Released"
events are wrong without the patch.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29904
2012-01-25 07:44:43 +00:00
4f3d6c9ae9
ar71xx: use the lzma loader on the Planex boards
...
SVN-Revision: 29900
2012-01-24 20:12:10 +00:00
5fa9768cee
ar71xx: rename Sysupgrade/{KR,RK} to Sysupgrade/{KR,RK}uImage
...
SVN-Revision: 29899
2012-01-24 20:12:08 +00:00
095c236694
ar71xx: fix the AP/Router LED definitons on MZK-W300NH
...
SVN-Revision: 29897
2012-01-24 18:40:38 +00:00
23e1b451dc
ar71xx: preset WLAN LED config on MZK-W300NH
...
SVN-Revision: 29896
2012-01-24 18:40:36 +00:00
23836d5908
ar71xx: remove hardcoded MTD layout from planex files
...
SVN-Revision: 29895
2012-01-24 18:40:34 +00:00
859c915077
ar71xx: pass mtdlayout to Planex boards via command line
...
SVN-Revision: 29894
2012-01-24 18:40:33 +00:00
6ad9bf8d17
ar71xx: remove an unused header file
...
SVN-Revision: 29893
2012-01-24 18:40:31 +00:00
02e77c6ae1
ramips: generate sysupgrade image for the ALL0256N
...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29884
2012-01-24 11:48:48 +00:00
944c8aacdb
ramips: add user-space support for ALL0256N
...
This adds uci-defaults and sysupgrade support for the ALL0256N.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29883
2012-01-24 11:48:47 +00:00
1932a7205c
ramips: add kernel support for ALL0256N
...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29882
2012-01-24 11:48:45 +00:00
17bb003891
ar71xx: nuke fs_all variable in image/Makefile
...
SVN-Revision: 29880
2012-01-24 09:47:25 +00:00
1fb88e2541
ar71xx: create interim kernel files in a separate dir
...
This reduces the size of the ImageBuilder tarball a lot.
SVN-Revision: 29879
2012-01-24 09:47:23 +00:00
a43e2f508f
ar71xx: prebuild all loaders in Image/Prepare stage
...
SVN-Revision: 29878
2012-01-24 09:47:22 +00:00
9cf1d4e06e
ramips: scripts updates
...
In this patch:
* rename Argus leds to avoid underscores
* rename Belkin F5D8235 v1 leds from f5d8234 to f5d8235
* remove Belkin F5D8235 v1 status led defined as storage led (it was
defined as usb led earlier, just in wrong place) - it should have
router led as in v2
* add Argus, Sparklan and Belkin F5D8235 v2 status leds
* add Belkin F5D8235 v1 and v2 usb leds
* fix Belkin F5D8235 v2 network config generation and mac address axtraction
* fix Sparklan board identification
* add Sparklan usb led (this board doesn't have usb connector by
default and the led is hidden also but if you are going to solder
the connector then you'll see the led too)
* add Sparklan network config generation and mac address extraction
* fix empty string test in network script and...
* ...sort case entries by the first board in the list
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29871
2012-01-23 10:23:32 +00:00
44517a3789
ar71xx: 3.2: fix build errors if PCI is not enabled
...
SVN-Revision: 29870
2012-01-23 08:52:21 +00:00
778db0a13d
ar71xx: fix compiler warning if PCI is not enabled
...
SVN-Revision: 29869
2012-01-23 08:52:18 +00:00
af015f956c
ar71xx: add initial support for 3.2
...
Tested on the following boards:
ALFA AP96
TL-MR3220 v1
TL-WR1043ND v1
TL-WR2543ND v1
TL-WR703N v1
TL-WR741ND v1
TL-WR741ND v4
WNDR3700 v1
WZR-HP-G300NH
SVN-Revision: 29868
2012-01-22 22:38:19 +00:00
386cbfe45b
ar71xx: move arch specific files to files-2.6.39
...
SVN-Revision: 29867
2012-01-22 22:38:11 +00:00
7b7427e52c
ar71xx: build ALFA AP96 images with default profile as well
...
SVN-Revision: 29866
2012-01-22 22:33:15 +00:00
dd49cca9d6
generic: 3.2: allow to build myloader mtd parser for ATH79
...
SVN-Revision: 29860
2012-01-22 18:43:39 +00:00
9be1b91644
generic: allow to build myloader mtd parser for 3.2+
...
SVN-Revision: 29858
2012-01-22 18:36:49 +00:00
809fe38e41
ramips fix f5d8235-v1 diag LED support
...
SVN-Revision: 29857
2012-01-22 18:11:39 +00:00
e7dee3aeed
ar71xx: wrt160nl_part: include module.h and fix compiler warnings
...
SVN-Revision: 29856
2012-01-22 17:55:38 +00:00
a7d344565b
ar71xx: tplinkpart: include module.h
...
SVN-Revision: 29855
2012-01-22 17:55:36 +00:00
6c2638c5e2
ar71xx: rename vsc7385 spi driver
...
SVN-Revision: 29853
2012-01-22 13:51:57 +00:00
bb16739db9
ar71xx: rename ap81 spi driver
...
SVN-Revision: 29852
2012-01-22 13:51:56 +00:00
5ef8b922fa
ar71xx: rename rb4xx spi drivers
...
SVN-Revision: 29851
2012-01-22 13:51:54 +00:00
aad175d5b6
ar71xx: rename the nxp_74hc153 driver
...
SVN-Revision: 29850
2012-01-22 13:51:52 +00:00
ef1c53b7b7
ar71xx: change board id of the UniFi board
...
SVN-Revision: 29849
2012-01-22 13:51:50 +00:00
f90e578903
ar71xx: include linux/module.h in the micrel phy driver
...
SVN-Revision: 29848
2012-01-22 13:51:49 +00:00
e9d8deaaed
ramips: add sysled and sysupgrade to wr512-3gn
...
Patch from #10035 .
SVN-Revision: 29847
2012-01-22 13:43:23 +00:00
8e662f28fe
generic: 3.2: don't disable lockdep for OOT modules
...
SVN-Revision: 29846
2012-01-22 09:57:39 +00:00
4625c9b5a4
generic: rtl8366: add rtl8366_smi_write_reg_noack helper
...
After issuing a soft reset on the RT8366{S,RB}
switch, waiting for the last acknowlegement fails
in rtl8366_smi_write_reg. Add a _noack version of
the function and use that for issuing a soft reset.
SVN-Revision: 29844
2012-01-21 22:44:09 +00:00
26d4e1876c
brcm47xx: add support for pcie host controller on bcma based SoCs.
...
This also adds minimal support for the BCMA43224 pcie wireless card.
SVN-Revision: 29843
2012-01-21 22:39:20 +00:00
557cf076b4
ramips: sysupgrade for ESR-9753
...
This patch add sysupgrade for Engenius ESR-9753
Signed-off-by: Artur Wronowski <arteqw@gmail.com>
SVN-Revision: 29824
2012-01-20 10:49:26 +00:00
aa8f9171f2
kernel: fix OCF for linux 3.2
...
Add skb_frag_page from 3.2 to OCF for 3.1 and earlier and use it.
SVN-Revision: 29818
2012-01-19 19:51:54 +00:00
fc512193a0
add missing kernel symbols
...
SVN-Revision: 29790
2012-01-19 01:57:22 +00:00
2fc3fe1d09
Make the grub timeout configurable on x86 targets
...
Signed-off-by: Justus Winter <4winter@informatik.uni-hamburg.de>
SVN-Revision: 29786
2012-01-19 01:14:45 +00:00
095f7f2da3
x86/config-3.2: add linux-3.2 symbols for x86
...
The following symbols are missing for x86, in sorted order.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 29783
2012-01-19 00:31:39 +00:00
dbfeb5d158
fix thinko in 102-ehci_hcd_ignore_oc patch
...
SVN-Revision: 29773
2012-01-18 07:56:02 +00:00
49eb3fd845
gigaset 76x
...
* fixes leds
* adds all leds found on the sx763 board
* removes board_config from flash layout because wireless data is stored in kernel (ath5k)
* fix button handling
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 29763
2012-01-17 12:10:35 +00:00
a2708d11e8
ramips: Rework ramips_eth to not require irqsave locking anymore
...
Previously the tx housekeeping was done in a spin_lock_irqsave critical
section which causes irqs to be disabled during that time. Since the
housekeeping is already prepared to be scheduled as a tasklet process
the housekeeping only in softirq context and revise the locking between
the tx path and the housekeeping tasklet by using a normal spin_lock
which in most situations will be a NOP anyway.
This makes sure that interrupts are only disabled for a short time
since in the worst case the housekeeping might have to free up to 256
skbs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 29762
2012-01-17 11:23:11 +00:00
034cf5643f
brcm47xx: add support for kernel 3.2
...
SVN-Revision: 29756
2012-01-15 21:18:34 +00:00
c3d134af12
brcm47xx: run kernel_oldconfig
...
SVN-Revision: 29755
2012-01-15 14:53:32 +00:00
f9e41adc80
add support for OMAP4 based boards, starting with the PandaBoard
...
SVN-Revision: 29753
2012-01-14 23:02:56 +00:00
6274648199
fixup arm xz support with recent changes
...
SVN-Revision: 29750
2012-01-14 22:55:04 +00:00
e65195c246
add missing symbols
...
SVN-Revision: 29749
2012-01-14 22:53:28 +00:00
b0479e2ca2
kernel: disable bridge igmp snooping in 3.2 as well
...
SVN-Revision: 29747
2012-01-14 14:57:03 +00:00
66895b7115
kernel: disable bridge igmp snooping by default to avoid multicast issues
...
SVN-Revision: 29744
2012-01-14 13:50:25 +00:00
9eb73ee6b7
kernel: ppc40x: ppc44x: add missing kernel config symbol
...
SVN-Revision: 29742
2012-01-14 12:04:17 +00:00
d5bc3a994b
brcm47xx: update usb driver
...
Add workarround for BCM5357 and BCM4749.
This patch contains the following fixes from George Kashperko:
* separate subroutines for controller initialization workarounds -
following CodingStyle recommendations;
* __devinit __devexit __devinitconst annotations for CONFIG_HOTPLUG;
* fix leak in ssb_hcd_create_pdev/bcma_hcd_create_pdev - as hci_res being
kmalloc'ed is never freed anywhere while platform_device_add_resources
will kmemdup resources right away;
* fix compilation error in ssb_hcd_resume - it will fail as soon as
CONFIG_PM is selected.
SVN-Revision: 29734
2012-01-13 20:11:23 +00:00
9d497cb132
rtl8366: fix rtl8366_smi_detect() after r29677
...
SVN-Revision: 29732
2012-01-13 19:17:58 +00:00
3883e71097
brcm63xx: add support for linux 3.2
...
SVN-Revision: 29731
2012-01-13 14:59:50 +00:00
1bc0abb058
kernel: add support for linux 3.2.1
...
SVN-Revision: 29730
2012-01-13 14:55:07 +00:00
f3f1075655
kernel: backport overlayfs v11 to 3.0 and 2.6.39
...
Should fix whiteout issues and missing files when using extroot.
SVN-Revision: 29727
2012-01-13 14:42:53 +00:00
c560444a58
kernel: update linux 3.1 to 3.1.9
...
SVN-Revision: 29726
2012-01-13 14:38:28 +00:00
e49d3e1d5b
kernel: update linux 3.0 to 3.0.17
...
SVN-Revision: 29725
2012-01-13 14:10:44 +00:00
e87bb77966
ar8216: use vlan configuration for connecting ports (forced to be untagged) even with vlan_enable=0, but keep them isolated before the switch has been configured this makes enable_vlan=0 practical for vlan passthrough
...
SVN-Revision: 29719
2012-01-12 10:15:11 +00:00
c33e016fa5
ar8216: do not strip vlan tags when running with vlan_enable=0
...
SVN-Revision: 29718
2012-01-12 10:15:08 +00:00
fbf81c8e79
ar71xx: move irq_to_gpio and gpio_to_irq into gpio.c
...
SVN-Revision: 29713
2012-01-11 18:00:50 +00:00
034b7f0ef5
Remove invalid LED GPIO from GW6200 board definition. GPIO 35 isn't intended to control ethernet LED (the led behaviour is a side effect) and using the gpio as an led causes kernel panics.
...
SVN-Revision: 29712
2012-01-11 13:47:48 +00:00
67f62cf5cf
ar71xx: disable ath79 in order to get rid of Kconfig warnings
...
SVN-Revision: 29711
2012-01-11 09:14:19 +00:00
88d8cdd503
ar71xx: pb44_spi: add shutdown handler
...
This allows to access the flash from a kexec'd kernel.
SVN-Revision: 29710
2012-01-11 09:14:18 +00:00
e1b7995aef
ar71xx: pb44_spi: call pb44_spi_{en,dis}able from probe/remove
...
SVN-Revision: 29709
2012-01-11 09:14:17 +00:00
67444c7795
ar71xx: pb44_spi: introduce pb44_spi_{en,dis}able helpers
...
SVN-Revision: 29708
2012-01-11 09:14:15 +00:00
0f566a376c
ar71xx: ar71xx_spi: add shutdown handler
...
This allows to access the flash from a kexec'd kernel.
SVN-Revision: 29707
2012-01-11 09:14:14 +00:00
09a6e3f662
ar71xx: ar71xx_spi: save and restore regs from probe/remove
...
SVN-Revision: 29706
2012-01-11 09:14:13 +00:00
714a9bd641
ar71xx: ar71xx_wdt: add shutdown handler
...
SVN-Revision: 29705
2012-01-11 09:14:11 +00:00
9727256330
ar71xx: refresh patches
...
SVN-Revision: 29683
2012-01-07 19:36:43 +00:00
4edff7d3ef
ar71xx: add a profile and build images for the TL-WR2543N/ND
...
SVN-Revision: 29682
2012-01-07 19:36:42 +00:00
a1dcbc66a6
ar71xx: add initial support for the TL-WR2543N/ND board
...
The WLAN LEDs are not working yet.
SVN-Revision: 29680
2012-01-07 19:36:35 +00:00
a56bdeff9d
ar71xx: allow to specify max read size for m25p80
...
Reading from the flash chip on the TL-WR2543ND seems buggy.
If the SPI flash driver tries to read too much data in one
SPI transfer, the flash chip returns bogus values. This can
be caused by a buggy flash chip on my board, or it can
be a bug in our SPI driver.
Add a workaround to the m25p80 driver until I find out the
root cause of the problem. The patch allows to specify the
maximum numner of bytes which can be read safely withint
one SPI transfer.
SVN-Revision: 29679
2012-01-07 19:36:33 +00:00
8b567fb508
generic: add driver for the RTL8367R/M switches
...
SVN-Revision: 29678
2012-01-07 19:36:31 +00:00
87fb92ee03
generic: rtl8366: preparing for RTL8367 support
...
* make clock delay configurable
* make read,write commands configurable
* use u16 for member and untag fields
SVN-Revision: 29677
2012-01-07 19:36:30 +00:00
43196813d7
generic: rtl8366_smi: add timeout message
...
SVN-Revision: 29676
2012-01-07 19:36:25 +00:00
67b2814842
ar71xx: local mac support on the wndr3700
...
The wndr3700 at least has no eth0 mac address and usually leverages
the first wireless device's mac when in a bridged scenario. If,
however, you want to route, and not bridge the interfaces, you
need a unique mac address for it.
This patch sets the local bit on the mac address pulled from the
wireless chip and uses the resulting address for eth0.
Patch-by: Dave Taht <dave.taht@gmail.com>
SVN-Revision: 29675
2012-01-07 17:24:44 +00:00
6c74274c8d
generic: improve MIPS kexec support
...
It is based on patches from the linux-longsoon-community git tree:
http://dev.lemote.com/cgit/linux-loongson-community.git/
Now the kernel can use the command line parameter from kexec-tools.
Runtime tested on ar71xx with 2.6.39.4 (the wathdog must be stopped
before executing the new kernel). Compile tested with lantiq (3.1.4)
and brcm47xx (3.0.12).
SVN-Revision: 29674
2012-01-07 16:29:16 +00:00
f638c6207b
ar71xx: fix sysupgrade on the TL-WR841N/ND v7 boards
...
SVN-Revision: 29672
2012-01-06 15:54:59 +00:00
1e848b17ad
ar71xx: add support for Redwave RW2458N
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 29669
2012-01-06 07:20:59 +00:00
84cd8a5ee0
ar71xx: fix RB-750 network configuration
...
SVN-Revision: 29668
2012-01-06 07:20:54 +00:00
8eb0b7ab3d
ar71xx: fix sections mismatch warnings in the nand drivers
...
SVN-Revision: 29667
2012-01-05 18:08:33 +00:00
232eb83f74
ar71xx: fix LED configuration on the RB-750
...
SVN-Revision: 29666
2012-01-05 18:08:28 +00:00
d65c6fe720
ar71xx: create profile and build image for the ALFA AP96 board
...
SVN-Revision: 29663
2012-01-04 21:13:57 +00:00
b8f0d86115
ar71xx: add inital support for the ALFA Network AP96 board
...
The microSD slot and the Real Time Clock is not working yet.
The miniPCIe interface is not tested due to the lack of a
suitable card.
SVN-Revision: 29662
2012-01-04 21:13:54 +00:00
807e046193
ar71xx: specify console kernel parameter for the Compex boards
...
SVN-Revision: 29660
2012-01-04 17:30:59 +00:00
923f3e3752
ar71xx: allow to use the command line hack on compex devices
...
SVN-Revision: 29659
2012-01-04 17:30:58 +00:00
2f53f82203
ar71xx: use the TL-MR3x20 code for the TL-WR841N/ND v7
...
These models are based on the AP99 reference board,
and uses the AR7241 SoC.
SVN-Revision: 29658
2012-01-04 17:30:57 +00:00
301b1b4f92
ar71xx: show correct model name on TL-WA701N/ND boards
...
SVN-Revision: 29657
2012-01-04 17:30:55 +00:00
ac68f0d8fa
ar71xx: add profile and build image for the TL-WA701N/ND boards
...
SVN-Revision: 29656
2012-01-04 17:30:54 +00:00
72019009c7
ar71xx: fix network configuration for the TL-WA901N/ND boards
...
SVN-Revision: 29654
2012-01-04 17:30:52 +00:00
90bfef9ec9
ar71xx: allow to use LAN LED on the TL-WA901N/ND boards
...
SVN-Revision: 29653
2012-01-04 17:30:50 +00:00
5eb502d9c1
ar71xx: add default LED configuration for the TL-MR3020
...
Also use the system LED for diagnostic.
SVN-Revision: 29652
2012-01-04 17:30:49 +00:00
1045c83527
ar71xx: add support for TP-Link TL-MR3020
...
This patch adds support for the TP-Link device TL-MR3020 which is very
similiar to the TL-WR703N.
The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions.
Only four LEDs can be controlled via GPIO. The power LED is connected to
the power supply.
The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals
of the sliding switch have been mapped to BTN_0 and BTN_1.
I have also setup a wiki page with details here:
http://wiki.openwrt.org/toh/tp-link/tl-mr3020
USB is working and has been tested with USB mass storage and USB UMTS
stick.
Wifi also seems to work.
Ethernet is working too.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29651
2012-01-04 17:30:47 +00:00
88223f87d1
ar71xx: use the new om-watchdog package for OM2P
...
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
SVN-Revision: 29648
2012-01-04 17:30:41 +00:00
a788f199c9
remove current RTSP support
...
SVN-Revision: 29643
2012-01-04 00:29:29 +00:00
237282ae8c
backport upstream commit e1738bd9cecc5c867b0e2996470c1ff20f66ba79 to affected kernels ( #9802 ) commit 8efa88540635 (sch_sfq: avoid giving spurious NET_XMIT_CN signals) forgot to call qdisc_tree_decrease_qlen() to signal upper levels that a packet (from another flow) was dropped, leading to various problems.
...
SVN-Revision: 29642
2012-01-03 23:08:15 +00:00
8854c90119
ar71xx: add profile and build factory image for the Hornet-UB board
...
SVN-Revision: 29637
2012-01-01 19:30:29 +00:00
1d3de89f3c
ar71xx: build images for the ALFA Network N2/N5 boards
...
SVN-Revision: 29636
2012-01-01 19:30:28 +00:00
1e68f10b87
ar71xx: add support for the ALFA Network N2/N5 boards
...
SVN-Revision: 29635
2012-01-01 19:30:25 +00:00
5c067db8a7
ar71xx: define LAN/WAN LEDs for the TL-WR741N/ND boards
...
SVN-Revision: 29631
2011-12-31 15:02:46 +00:00
fff02e6ea8
ar71xx: enable SWCONFIG_LEDS
...
SVN-Revision: 29630
2011-12-31 15:02:40 +00:00
5fa65cba6e
kernel: swconfig: introduce a generic switch LED trigger
...
SVN-Revision: 29627
2011-12-31 15:02:30 +00:00
8c2482f76e
ar71xx: ag71xx: implement get_port_{link,stats} callbacks
...
SVN-Revision: 29626
2011-12-31 15:02:26 +00:00
975355a2b1
kernel: swconfig: add get_port_{link,stats} callbacks
...
SVN-Revision: 29625
2011-12-31 15:02:24 +00:00
557009bbdb
ar71xx: fix LEDs on the WRT400N
...
SVN-Revision: 29624
2011-12-31 13:54:11 +00:00
244c322d25
ramips: rt288x: add support for the Belkin F5D8235-4 v1 board
...
Patch-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 29617
2011-12-28 08:43:43 +00:00
f50b02b559
ramips: rt288x: change base address and window size of flash bank 0
...
SVN-Revision: 29616
2011-12-28 08:43:36 +00:00
98437278c4
ramips: rt305x: add support for the ALFA Networks W502U (R36) board
...
SVN-Revision: 29615
2011-12-28 08:43:32 +00:00
76dacee995
ar71xx: enable sysupgrade support for airrouter
...
Works for me! ;-)
Patch-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 29614
2011-12-27 16:59:43 +00:00
c6ee919b2a
ar71xx: fix sysupgrade on PB42/PB44 boards
...
SVN-Revision: 29613
2011-12-27 16:57:01 +00:00
723d8dd74f
ramips: rt288x: add support for the Buffalo WLI-TX4-AG300N board
...
SVN-Revision: 29612
2011-12-27 16:56:30 +00:00
9fa33ceee2
add missing config symbol
...
SVN-Revision: 29610
2011-12-25 13:33:18 +00:00
11125d68ed
brcm47xx: fix usb on more recent bcma based devices.
...
SVN-Revision: 29605
2011-12-23 17:21:52 +00:00
7b1e525b56
ramips: initial support for Sitecom WL-351 v1 002
...
This add support for the Sitecom WL-351 v1 002.
In principle the Engenius ESR9850 should also work with this, but I
don't have the hardware to test it.
Since an external gigabit switch (RTL8366RB) is used,
I had to modify the ramips_esw driver to add a 'bypass' mode, which
just configures it to not filter the vlan tags.
Also two initialization words (FCT2 and FPA2) are set to different
values by u-boot than what the driver is using and it only seems to
work correctly when they not overridden by the driver, so I
added them to the platform specific data as reg_initval_fct2 and
reg_initval_fpa2.
With this wired lan works as expected, however I'm still having some
trouble with the wireless lan:
It only works after I rmmod & re-insmod rt2800pci and then
reconfigure it in the webinterface, but not directly after
rebooting.
The symptom of this is wpad saying:
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: associated (aid 1)
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> WPA: pairwise key handshake completed (RSN)
Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: authenticated
But wpa_supplicant on the client saying:
Authentication with <wl351mac> timed out.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 29604
2011-12-23 14:27:16 +00:00
2cb946f5b4
ramips: add support for the Senao/EnGenius ESR-9753 board
...
Signed-off-by: Artur Wronowski <arteqw@gmail.com>
SVN-Revision: 29603
2011-12-23 14:27:10 +00:00
03bce34384
ramips: define firmware partition for Omnima MiniEMBWiFi
...
Patch-by: Ivan Ignjatic <ivan@omnima.co.uk>
SVN-Revision: 29602
2011-12-23 14:27:05 +00:00
db0a1db257
ar71xx: set a reserved bit that resets to 1 when writing the address table control register on the ar7240 switch (should fix #10547 )
...
SVN-Revision: 29598
2011-12-22 05:43:53 +00:00
8799627ef0
ar71xx: add default network config for buffalo WZR-HP-G300NH2 and WZR-HP-G450H
...
Thanks netprince for reporting and testing.
SVN-Revision: 29595
2011-12-21 19:32:40 +00:00
ebefe1eb3a
the mach file of the WZR-HP-G300NH2 accidentally claimed the mach id of the WZR-HP-AG300H, correct the id ( #10649 )
...
SVN-Revision: 29593
2011-12-21 01:27:48 +00:00
0cd03df3b1
brcm47xx: remove patch starting adding brcm4716 to ssb
...
brcm4716 is supported by bcma now we do not need this patch
SVN-Revision: 29576
2011-12-19 23:55:20 +00:00
5b8686c303
brcm47xx: add new usb driver for bcma bus and replace ssb usb driver.
...
This new usb driver uses an extra device so the ehci and the ohci driver are not depending on ech other any more.
SVN-Revision: 29575
2011-12-19 23:39:13 +00:00
1aa5a61754
kernel: update bcma and ssb to version master-2011-12-16 from wireless-testing
...
SVN-Revision: 29574
2011-12-19 23:33:03 +00:00
91d0ef6f19
brcm47xx: remove support for kernel 2.6.39
...
There are problems with the patches for kernel 2.6.39 and I do not want to support two different sets of patches.
SVN-Revision: 29573
2011-12-19 23:26:15 +00:00
11013ad947
ar71xx: add missing wireless led changes for wzr-hp-g300nh2
...
SVN-Revision: 29568
2011-12-19 09:04:15 +00:00
0cc056cb7e
ar71xx: add support for the wzr-hp-g300nh2
...
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
SVN-Revision: 29567
2011-12-18 22:20:17 +00:00
5a0a2b2f1b
ar71xx: use 64kraw template on more TP-Link boards
...
SVN-Revision: 29561
2011-12-17 18:49:55 +00:00
67c7980290
ar71xx: connect GMAC0 to the internal switch on DB120
...
Because the external switch has no driver yet, connect GMAC0
to the PHY4 of the internal switch for now. This allows to
use the DB120 board as a router with 4LAN+1WAN ports.
SVN-Revision: 29557
2011-12-15 22:25:38 +00:00
5bbd416e38
ar71xx: add defines for the AR934X GMAC interface
...
SVN-Revision: 29556
2011-12-15 22:25:36 +00:00
e47a8c2bb2
ar71xx: fix GMAC1 interface speed on the DB120 board
...
SVN-Revision: 29555
2011-12-15 22:25:35 +00:00
36bc2c2c80
ar71xx: ag71xx: fix switch port setup for AR934X
...
SVN-Revision: 29554
2011-12-15 22:25:32 +00:00
00667c3846
ar71xx: ag71xx: allow to connect PHY4 to the CPU on AR934X
...
SVN-Revision: 29553
2011-12-15 22:25:30 +00:00
0540970345
ar71xx: ag71xx: setup switch interface mode on AR934X
...
SVN-Revision: 29552
2011-12-15 22:25:29 +00:00
44014110b8
ar71xx: ag71xx: detect the built-in switch of the AR934X SoCs
...
SVN-Revision: 29551
2011-12-15 22:25:28 +00:00
e2a546d475
ar71xx: allow to attach the internal switch for AR934x
...
SVN-Revision: 29550
2011-12-15 22:25:22 +00:00
9ae65588d8
ar71xx: introduce ar71xx_switch_data
...
SVN-Revision: 29549
2011-12-15 22:25:11 +00:00
bfe747b7d9
ar71xx: build images for TL-WR741N/ND v2
...
SVN-Revision: 29548
2011-12-15 22:03:48 +00:00
aefff26624
ar71x: use raw squashfs images for TP-Link boards
...
SVN-Revision: 29547
2011-12-15 22:03:46 +00:00
d5bd28ffae
ar71xx: create a template for using unpadded squashfs images
...
SVN-Revision: 29546
2011-12-15 22:03:45 +00:00
dbc4fa4b5b
ar71xx: put squash image right after the kernel on TP-Link boards
...
SVN-Revision: 29545
2011-12-15 22:03:44 +00:00
850be54b72
ar71xx: tplinkpart: allow to detect JFFS2 as well
...
SVN-Revision: 29543
2011-12-15 22:03:40 +00:00
b7d7481b07
ar71xx: ag71xx: check PHY IDs before accessing the switch registers
...
SVN-Revision: 29541
2011-12-15 13:25:23 +00:00
0655552860
ar71xx: ag71xx: don't use port 4 of the switch, it is not connected on ar724x
...
SVN-Revision: 29540
2011-12-15 13:25:21 +00:00
204fc6bed5
ar71xx: ag71xx: nuke ar7240sw_init
...
SVN-Revision: 29539
2011-12-15 13:25:20 +00:00
d1f7783612
ar71xx: fix mac addresses on jjPlus devices
...
SVN-Revision: 29538
2011-12-15 13:25:18 +00:00
d3058b8f8c
ar71xx: build image for the Hornet-UB board
...
SVN-Revision: 29536
2011-12-14 20:54:11 +00:00
b9c5cb5c9a
ar71xx: add support for ALFA Network's Hornet-UB board
...
SVN-Revision: 29535
2011-12-14 20:54:10 +00:00
66c8cc0f6d
ar71xx: add GPIO function bit defines for AR933X
...
SVN-Revision: 29534
2011-12-14 20:54:07 +00:00
0c38d36488
ramips: add support for Omnima MiniEMBWiFi board
...
This patch adds support for the Omnima MiniEMBWiFi
Ralink RT3050F based board.
Based on a patch by Ivan Ignjatic <ivan at omnima.co.uk>
SVN-Revision: 29533
2011-12-14 20:51:26 +00:00
7076d74b21
ar71xx: fix gpio count for ar7241/ar7242
...
SVN-Revision: 29532
2011-12-14 20:47:24 +00:00
b878f4a927
ar71xx: register extra leds behind the wireless mac on wzr-hp-g450h
...
SVN-Revision: 29531
2011-12-14 20:21:42 +00:00
e3017bc05e
ath9k: add support for registering extra leds connected to the wmac gpio lines
...
SVN-Revision: 29530
2011-12-14 20:21:36 +00:00
d2717d3d47
ar71xx: get rid of squashfs-4k images
...
SVN-Revision: 29522
2011-12-13 20:41:24 +00:00
5afedc67e2
generic: disable 'small sector' erase in m25p80 driver
...
This fixes the issues with the jffs2 images on various boards. Using
JFFS2 on devices with 4KiB erase sectors is not safe:
http://lists.infradead.org/pipermail/linux-mtd/2011-June/036591.html
SVN-Revision: 29521
2011-12-13 20:41:22 +00:00
4a441570ca
kernel: move linux/ath9k_platform.h to generic files so that it can be reused from other targets
...
SVN-Revision: 29516
2011-12-13 15:14:59 +00:00
3806671fe5
ar71xx: fix wireless led on wzr-hp-g450h
...
SVN-Revision: 29515
2011-12-13 15:00:43 +00:00
2dd7dfb1c9
ar71xx: enable AR9341 support at setup.c
...
Patch-by: dyq <729650915@qq.com>
SVN-Revision: 29514
2011-12-13 14:59:43 +00:00
058998acdb
ar71xx: Build images for Netgear WNDRMAC and WNDRMACv2
...
The WNDRMAC is a WNDR3700v2 (64MB RAM, 16MB flash) in a white case. The
WNDRMACv2 is a WNDR3800 (128MB RAM, 16MB flash) in a WNDRMAC case.
The WNDRMAC case doesn't have "holes" or labels for the 2.4GHz LED or
switch ports 2-4. The stock firmware uses a single LED (in the 5GHz
position) to indicate the status of both radios, and a single LED (in the
switch port 1 position) to indicate the status of all LAN ports. The
"missing" LEDs are present on the board, and easily shine through the
case. Unlike the stock firmware, OpenWrt will use these "hidden" LEDs.
I've tested the WNDRMACv2 image. I don't have a v1 WNDRMAC, but assume
that this is sufficient to build a fully-functional image.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29513
2011-12-13 14:59:40 +00:00
48f9717371
ar71xx: add gpios and usb for wzr-hp-g450h
...
SVN-Revision: 29509
2011-12-13 13:33:44 +00:00
4ca2d86493
ar71xx: use RedBoot parser on PB44
...
SVN-Revision: 29501
2011-12-11 15:52:47 +00:00
934eef78ca
convert to gpiolib
...
Signed-off-by: karlp@tweak.net.au
SVN-Revision: 29486
2011-12-09 07:52:10 +00:00
6e69765559
ar71xx: fix WNDR3x00 factory image generation
...
Factory images for WNDR3700v2 and WNDR3800 should contain these model IDs
for the device: field in their DNI tags, not WNDR3700.
This regressed in r29434, which redid WNDR3x00 model detection. The sixth
parameter to Image/Build/Netgear is only used as the -B argument to
mkdniimg, which is used to set the device: field. In r29434, this was
erroneously changed to be WNDR3700 for all models. The tools to flash
factory images (U-Boot's TFTP server and the factory software's upgrade
utility) may refuse to honor images with incorrect device: fields in their
DNI tags.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29473
2011-12-07 06:55:50 +00:00
8eb8a6e1e7
ar71xx: fix WNDR3x00 model detection
...
Detect the model name for /tmp/sysinfo/model based on 10 bytes at offset
56 in the art (caldata) mtd partition.
r29434 redid WNDR3x00 model detection, attempting to distinguish between
WNDR3700v2 and WNDR3800 by checking MemTotal in /proc/meminfo. However, it
contained a bug: it put the awk inside a $(...), with the result that all
WNDR3700v2 and WNDR3800 models would be reported as WNDR3800. This patch
checks the model name stored in the art partition, as is done by U-Boot
shipping on the WNDR3800. It has the likely advantage of working with
future models based on the WNDR3700 board. It also will not mis-detect
units on which people install more memory.
I have tested this patch on WNDR3700 (v1), WNDR3700v2, and WNDR3800.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29472
2011-12-07 06:55:39 +00:00
43bd4c6ad1
ramips: fix mac addresses on the DIR-300/600 boards
...
SVN-Revision: 29471
2011-12-06 20:06:08 +00:00
e33bb9ec66
linux: update 3.1 to 3.1.4
...
SVN-Revision: 29470
2011-12-06 19:50:30 +00:00
6e2ae90f4a
linux: update 3.0 to 3.0.12
...
SVN-Revision: 29469
2011-12-06 19:50:25 +00:00
c6b2b98812
ar71xx: create firmware image for the TL-WR740N/ND v4 boards
...
Based on a patch by Cristian Deluxe <djcristiandeluxe@gmail.com>
SVN-Revision: 29468
2011-12-06 16:26:44 +00:00
fbfad4e9b4
ar71xx: use hw_id, hw_rev and flash_layout with mktplinkfw
...
SVN-Revision: 29467
2011-12-06 16:26:43 +00:00
d753e08c79
ar71xx: fix TL-MR3x20 profile names in image/Makefile
...
SVN-Revision: 29463
2011-12-06 13:53:21 +00:00
62d8009cdd
ar71xx: cleanup TP-Link profiles
...
SVN-Revision: 29461
2011-12-06 10:29:25 +00:00
f7a482d382
ar71xx: add TP-Link board detection
...
SVN-Revision: 29459
2011-12-05 21:11:01 +00:00
bdc2eca7de
ar71xx: use correct mac on the lan interface on several TP-LINK devices
...
SVN-Revision: 29458
2011-12-05 21:10:58 +00:00
0103069372
ar71xx: allow to pass negative offset values for ar71xx_init_mac
...
SVN-Revision: 29457
2011-12-05 21:10:55 +00:00
ada92aee62
ar71xx: don't register PCI controller on AR934x if PCIE_RC bit is not set
...
SVN-Revision: 29456
2011-12-05 18:21:15 +00:00
c6bcf8d1d8
ar71xx: verify hardware id of firmware images on TP-Link boards
...
SVN-Revision: 29455
2011-12-05 18:11:51 +00:00
5ef6ec4a31
ramips: set mac addresses for the NBG-419N
...
Based on a patch by Nerijus Baliunas <nerijus@users.sourceforge.net>
SVN-Revision: 29454
2011-12-05 17:27:07 +00:00
750d560767
ramips: set preinit interface mac on the hw550-3g board
...
Based on a patch by Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29453
2011-12-05 17:27:06 +00:00
b5d7b359b2
ramips: use ramips_get_mac_* functions in the preinit script
...
SVN-Revision: 29452
2011-12-05 17:27:04 +00:00
4d5b940e66
ramips: move ramips_get_mac_* functions to lib/ramips.sh
...
SVN-Revision: 29451
2011-12-05 17:27:03 +00:00
cc853acb3a
ramips: add ramips_ prefix to get_mac_{binary,nvram} functions
...
SVN-Revision: 29450
2011-12-05 17:27:02 +00:00
b1137d48a4
ramips: fix network configuration setup
...
SVN-Revision: 29448
2011-12-05 16:54:48 +00:00
4dc9092f4b
ar71xx: reclaim some unused space on TP-Link boards
...
With the default OpenWrt configuration, this increases the size
of the rootfs_data partition by 384KB/128KB on the older/newer
TP-Link models.
SVN-Revision: 29447
2011-12-05 14:52:36 +00:00
3e7a6d182a
ar71xx: check squashfs signature in TP-Link mtd parser
...
SVN-Revision: 29446
2011-12-05 14:52:33 +00:00
feebf484ba
ar71xx: use the lzma-loader on TP-Link boards w/o lzma support
...
SVN-Revision: 29444
2011-12-05 14:52:28 +00:00
d42968351f
ar71xx: add lzma loader
...
SVN-Revision: 29443
2011-12-05 14:52:25 +00:00
1f809532de
ar71xx: add preliminary support for wzr-hp-g450h
...
SVN-Revision: 29441
2011-12-05 14:20:51 +00:00
d1f63f8538
ar71xx: move multi-m25p80 concat code from wzr-hp-ag300h mach code to dev-m25p80.c, other buffalo routers use it as well
...
SVN-Revision: 29440
2011-12-05 14:20:44 +00:00
4cc2b9bb06
ar71xx: rewrite WNDR3700/3800 handling
...
SVN-Revision: 29434
2011-12-05 13:03:54 +00:00
78699c2e51
add some missing wndr3800 base-files definitions
...
SVN-Revision: 29433
2011-12-05 12:56:21 +00:00
5177814ade
ar71xx: change user-space board detection
...
SVN-Revision: 29432
2011-12-05 12:56:20 +00:00
8a3a60fc64
ar71xx: allow WNDR3700 image creation to fail if kernel/rootfs too big
...
SVN-Revision: 29431
2011-12-05 12:47:53 +00:00
56c9b50006
ramips: fix argus board rootfs size
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29422
2011-12-04 15:24:57 +00:00
7cfa39f032
ar71xx: use the tp-link parser on the tp-link boards
...
Also remove static partition maps.
SVN-Revision: 29416
2011-12-03 18:13:31 +00:00
514b1167c9
ar71xx: add mtd partition parser for the TP-Link boards
...
SVN-Revision: 29415
2011-12-03 18:13:27 +00:00
fc7fb29bae
ar71xx: run the RedBoot parser only on the RedBoot based boards
...
SVN-Revision: 29414
2011-12-03 18:13:25 +00:00
9cc28d5aa0
ar71xx: run the MyLoader parser only on the WP543 board
...
SVN-Revision: 29413
2011-12-03 18:13:23 +00:00
67a0b9aada
ar71xx: run the wrt160nl parser only on the WRT160NL board
...
Also remove static mtd partition definitions.
SVN-Revision: 29412
2011-12-03 18:13:20 +00:00
c8acd6e013
ar71xx: allow to pass part_probe types to the m25p80 driver
...
SVN-Revision: 29411
2011-12-03 18:13:18 +00:00
20483faed0
ar71xx: create initramfs images for the newer TP-Link boards
...
SVN-Revision: 29410
2011-12-03 16:57:23 +00:00
9a2005e5e6
ar71xx: remove swconfig and wpad-mini from custom profiles
...
SVN-Revision: 29408
2011-12-03 16:33:41 +00:00
bc1d818610
ar71xx: add uboot-envtools to the default package list
...
SVN-Revision: 29407
2011-12-03 16:33:40 +00:00
a02a9c3f8b
ar71xx: reclaim unused space in WNDR3700/3800 images
...
Patch by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29406
2011-12-03 16:33:38 +00:00
ac82296c53
ar71xx: add a profile and build image for the OM2P board
...
[juhosg: the name of the final image has been changed to
'openwrt-ar71xx-generic-om2p-squashfs-factory.bin']
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
SVN-Revision: 29397
2011-12-01 22:49:05 +00:00
f188f1bad5
ar71xx: add support for Ubiquiti AirRouter
...
Signed-off-by: Gergely Barta <gergely.barta@printerfairkft.hu>
SVN-Revision: 29395
2011-12-01 22:49:02 +00:00
0612667c34
ar71xx: configure default led behavior for the OM2P
...
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
SVN-Revision: 29394
2011-12-01 22:48:59 +00:00
3fccc3b376
ramips: enable sysupgrade on the RT-N15 board
...
SVN-Revision: 29393
2011-12-01 22:48:58 +00:00
4b2d1c3ad3
ramips: wrap long line in platform upgrade script
...
SVN-Revision: 29392
2011-12-01 22:48:57 +00:00
d622263588
ramips: add profile for the Asus RT-N15
...
This uses previously submitted rtl8366 kernel packages.
[juhosg: The kmod-gpio-dev package has been removed from the package list.]
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29391
2011-12-01 22:48:55 +00:00
3a9e02fa41
ramips: setup default network configuration for RT-N15
...
Based on a patch by Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29390
2011-12-01 22:48:54 +00:00
fc61c107f0
ramips: rt288x: add swconfig and rtl8366{s,_smi} drivers to the default profile
...
It is needed by the RT-N15 board.
SVN-Revision: 29389
2011-12-01 22:48:53 +00:00
80221fcd2a
ramips: remove default network configuration, and generate that from uci-defaults
...
SVN-Revision: 29387
2011-12-01 22:48:51 +00:00
4f6c58adac
ramips: use /lib/functions/uci-defaults.sh
...
SVN-Revision: 29386
2011-12-01 22:48:48 +00:00
39348e387f
ar71xx: use /lib/functions/uci-defaults.sh
...
SVN-Revision: 29385
2011-12-01 22:48:47 +00:00
569d8de6d6
ramips: simplify uci-defaults/network script
...
SVN-Revision: 29383
2011-12-01 22:48:45 +00:00
66c9a351dd
ramips: setup mac and network interfaces from separate functions
...
SVN-Revision: 29382
2011-12-01 22:48:43 +00:00
62d18e9f9a
ramips: fix Asus RT-N15 board support
...
Fix Asus RT-N15 flash partitions and make an image.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29381
2011-12-01 22:48:42 +00:00
2dd79d55c7
ramips: Sparklan wcr-150gn board fixes
...
* Fix partition sizes.
* Add buttons and leds.
* Register usb.
* Remove unnecessary stuff from image Makefile
* Fix rt2x00 eeprom extract.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29380
2011-12-01 22:48:41 +00:00
7c678e7511
ramips: fix package name of kmod-input-gpio-buttons
...
Based on a patch from Omnima Limited.
SVN-Revision: 29379
2011-12-01 22:48:39 +00:00
2ed38b24a8
ramips: move kmod-rt2800-pci to DEFAULT_PACKAGES
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29378
2011-12-01 22:48:38 +00:00
295e04084c
ramips: setup bc2 mac addresses from the generic network script
...
SVN-Revision: 29377
2011-12-01 22:48:37 +00:00
02f95d4fb3
ramips: combine network setup for all boards in one file
...
Inspired by the patch from Roman Yeryomin. Thanks, Roman!
This removes unnecessary duplication and simplifies network setup for new
boards. It would be a one line change most likely.
[juhosg: setup lan and wan interfaces for unspecified rt3x0x based boards
in order to avoid regression]
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
SVN-Revision: 29376
2011-12-01 22:48:35 +00:00
88cb7ae104
omap24xx: bump to 3.1.3
...
SVN-Revision: 29349
2011-11-28 12:46:18 +00:00
bf7316424c
lantiq: bump to 3.1.3
...
SVN-Revision: 29348
2011-11-28 10:22:58 +00:00
5e83009a52
targets: fix CONFIG_USB_STORAGE_* inconsistency
...
* all options were switched from bool to tristate in 2.6.30
* add/change/move them to generic, disabled by default
* remove extinct CONFIG_USB_STORAGE_DPCM dropped in 2.6.29, merged with CONFIG_USB_STORAGE_SDDR09
* remove extinct CONFIG_USB_STORAGE_SIERRA option in 2.6
* cleanup ordering
SVN-Revision: 29337
2011-11-25 20:47:44 +00:00
f20797306a
ar71xx: modify phy mask of the WP543 board
...
This fixes ethernet on newer boards. Based on a patch from #9702 .
SVN-Revision: 29328
2011-11-24 20:09:43 +00:00
c20d7378e5
ar71xx: fix wndr3800 machine name
...
This fixes the machine name in /proc/cpuinfo and luci status page machine name.
Signed-off-by: Petri Rosenström <petri.rosenstrom@gmail.com>
SVN-Revision: 29326
2011-11-24 20:09:38 +00:00
600b6efc41
ar71xx: copy atheros initramfs images to the image directory
...
SVN-Revision: 29325
2011-11-24 20:09:35 +00:00
d97cf76790
ar71xx: specify mtd layout in command line for the DB120 board
...
SVN-Revision: 29324
2011-11-24 20:09:32 +00:00
9389593db9
lantiq: drop 009-MIPS-make-oprofile-use-cp0_perfcount_irq-if-it-is-se.patch
...
This patch is/was a duplicate of generic/patches-3.1/307-mips_oprofile_fix.patch
SVN-Revision: 29294
2011-11-23 12:22:15 +00:00
4982ca983c
lantiq: * fixes ath5k eeprom handling * fixes sx76x * adds sx76x to userland api * minor style cleanups
...
Signed-of-by: Andrej Vlašić <andrej.vlasic0@gmail.com>
SVN-Revision: 29292
2011-11-22 18:50:51 +00:00
718907b661
don't package gpioctl by default
...
SVN-Revision: 29288
2011-11-21 16:36:39 +00:00
c33f21ae95
target/uml: export atomic64_* functions on 32-bit x86
...
SVN-Revision: 29287
2011-11-21 14:28:33 +00:00
9990523a0f
ar71xx: set GE0 phy_mask for AR933x
...
SVN-Revision: 29274
2011-11-20 11:30:10 +00:00
b5739aabd9
fix D-Link DSL-2650U image generation
...
SVN-Revision: 29266
2011-11-19 21:34:51 +00:00
8bac0df4ae
linux: update 3.0 to 3.0.9
...
SVN-Revision: 29264
2011-11-19 18:39:12 +00:00
ae90aa4efd
build images for D-Link DSL-2650U ( #9003 )
...
SVN-Revision: 29238
2011-11-18 10:37:03 +00:00
0b86c2648a
omap24xx: Fix cbus nested IRQ acking
...
SVN-Revision: 29237
2011-11-17 22:31:27 +00:00
df2810831c
omap24xx: Fix initialization of software IRQ mask
...
SVN-Revision: 29236
2011-11-17 21:02:00 +00:00
3f92f7dd90
omap24xx: Update 3.1 config
...
SVN-Revision: 29234
2011-11-17 19:35:57 +00:00
4793be2df9
omap24xx: Some retu/tahvo IRQ fixes
...
SVN-Revision: 29233
2011-11-17 18:06:19 +00:00
630bafc5dd
omap24xx: Add basic kexec fixes.
...
SVN-Revision: 29232
2011-11-17 14:57:34 +00:00
06c986984e
omap24xx: Add workaround for omapfb locking bug.
...
SVN-Revision: 29201
2011-11-16 22:34:38 +00:00
0f03e17bd0
Revert r29193
...
SVN-Revision: 29195
2011-11-16 19:03:23 +00:00
93f02b1ba0
omap24xx: Set platform specific optimization flags
...
SVN-Revision: 29194
2011-11-16 19:02:12 +00:00
b058e97af4
n810: Add xmodmap to profile
...
SVN-Revision: 29193
2011-11-16 19:01:19 +00:00
8d66465b08
include bridge and 8021q modules by default
...
SVN-Revision: 29164
2011-11-15 22:24:22 +00:00
bbe96f13a6
lantiq: add runtime generation of /etc/config/network
...
SVN-Revision: 29161
2011-11-15 18:21:00 +00:00
79a4642b40
lantiq: fix falcon build breakage
...
dev-wifi-rt2x00 fails to build on falcon due to missing pci
SVN-Revision: 29129
2011-11-14 18:55:58 +00:00
f27548448b
ar71xx: fix USB LED on the DB120 board
...
SVN-Revision: 29126
2011-11-14 17:43:15 +00:00
6ebbb1329d
ar71xx: add a function for selecting output signal on a given GPIO pin
...
SVN-Revision: 29125
2011-11-14 17:43:14 +00:00
0c1d3617d7
ar71xx: fix GPIO function handling on AR934x
...
SVN-Revision: 29124
2011-11-14 17:43:13 +00:00
aa0c8c4885
ar71xx: add AR71XX_ prefix to GPIO_REG_* defines
...
SVN-Revision: 29123
2011-11-14 17:43:11 +00:00
62a7795afd
ar71xx: merge nand scan patch
...
SVN-Revision: 29122
2011-11-14 17:43:10 +00:00
12dae96097
ar71xx: fix a compiler warning
...
SVN-Revision: 29110
2011-11-14 13:07:47 +00:00
5ae0fd802c
ar71xx: fix GPIO count for AR934x
...
SVN-Revision: 29109
2011-11-14 13:07:45 +00:00
e52269364a
ar71xx: flush DDR writeback buffers for WMAC and PCIe on AR934X
...
SVN-Revision: 29108
2011-11-14 11:49:53 +00:00
3104d70552
ar71xx: use a dummy irq chip for WMAC and PCIe irq hadling
...
SVN-Revision: 29107
2011-11-14 11:49:51 +00:00
42e8ae09b5
ar71xx: add AR934X_RESET_REG_PCIE_WMAC_INT_STATUS defines
...
SVN-Revision: 29106
2011-11-14 11:49:49 +00:00
c15caea360
ar71xx: add an irq parameter for ar724x_pcibios_init
...
SVN-Revision: 29105
2011-11-14 11:49:47 +00:00
cf90b24bb9
ar71xx: remove hardwired interface parameters from mach-* files
...
SVN-Revision: 29103
2011-11-14 07:38:09 +00:00
defc79cb40
ar71xx: force hardwired interface parameters in ar71xx_add_device_eth
...
SVN-Revision: 29102
2011-11-14 07:38:07 +00:00
6f4bc1ce37
ar71xx: use if-else instead of conditional operators in ar71xx_add_device_eth
...
SVN-Revision: 29101
2011-11-14 07:38:05 +00:00
7f787707de
build images for Pirelli A226M ( #10409 )
...
SVN-Revision: 29045
2011-11-13 19:19:22 +00:00
5dc2098448
register uart0 on DWV-S0 boards ( #10409 )
...
SVN-Revision: 29044
2011-11-13 19:19:18 +00:00
56a96ba876
refresh 3.0 patches
...
SVN-Revision: 29043
2011-11-13 19:19:14 +00:00
54da5cf11f
refresh 2.6.39 patches
...
SVN-Revision: 29042
2011-11-13 19:19:10 +00:00
717a4391d7
rename 456-board_DWV-S0_ehci.patch to 456-board_DWV-S0_fixes.patch
...
SVN-Revision: 29041
2011-11-13 19:19:05 +00:00
c093c9df34
fix typo, load ip17xx switch module
...
SVN-Revision: 29039
2011-11-13 18:41:26 +00:00
368bbc510b
ar71xx: enable has_gbit flag on AR724{0,1}
...
SVN-Revision: 29026
2011-11-13 17:36:36 +00:00
15d7016c9f
ar71xx: fixup onboard PCIe chip registration on the DB120 board
...
SVN-Revision: 29022
2011-11-13 12:48:03 +00:00
f623066e60
ar71xx: drop DB120_WMAC_MAC_OFFSET, it is not needed
...
SVN-Revision: 29021
2011-11-13 12:48:01 +00:00
d2316b2a45
ar71xx: ag71xx: add support for getting switch port link status
...
SVN-Revision: 29017
2011-11-13 11:27:04 +00:00
d0db89133c
ar71xx: remove mii_ctrl resources of the ethernet devices
...
SVN-Revision: 29016
2011-11-13 11:27:03 +00:00
34015ed6e8
ar71xx: ag71xx: remove unused mii_ctrl field from struct ag71xx
...
SVN-Revision: 29015
2011-11-13 11:27:01 +00:00
2d882cff23
ar71xx: ag71xx: remove unused mii_cfg related functions and defines
...
SVN-Revision: 29014
2011-11-13 11:27:00 +00:00
538a9493b9
ar71xx: set MII interface speed from the set_speed callbacks
...
SVN-Revision: 29013
2011-11-13 11:26:59 +00:00
93cd46be13
ar71xx: rename set_pll callback to set_speed in ag71xx_platform_data
...
Also rename the corresponding callback functions.
SVN-Revision: 29012
2011-11-13 11:26:57 +00:00
9579bb4267
ar71xx: ag71xx: remove MII interface setup code
...
SVN-Revision: 29011
2011-11-13 11:26:56 +00:00
da64ce8603
ar71xx: configure MII interface type from ar71xx_setup_phy_if_mode
...
SVN-Revision: 29010
2011-11-13 11:26:54 +00:00
0112153a0e
ar71xx: fix occasional kernel hangs during boot on AR934x
...
The patch taken from the linux-mips mailing list.
The Kernel hangs occasionally during boot after
"Calibrating delay loop..". This is caused by the
c0_compare_int_usable() routine in cevt-r4k.c
returning false which causes the system to disable
the timer and hang later. The false return happens
because the routine is using a series of four calls
to irq_disable_hazard() as a delay while it waits
for the timer changes to propagate to the cp0 cause
register. On newer MIPS cores, like the 74K, the
series of irq_disable_hazard() calls turn into ehb
instructions and can take as little as a few clock
ticks for all 4 instructions. This is not enough of
a delay, so the routine thinks the timer is not
working.
This fix uses up to a max number of cycle counter
ticks for the delay and uses back_to_back_c0_hazard()
instead of irq_disable_hazard() to handle the hazard
condition between cp0 writes and cp0 reads.
SVN-Revision: 29009
2011-11-13 11:26:52 +00:00
1afc76ea13
ar71xx: refresh kernel patches
...
SVN-Revision: 29008
2011-11-13 11:26:51 +00:00
d8acb75009
linux: update 3.1 to 3.1.1
...
SVN-Revision: 29007
2011-11-13 10:48:05 +00:00
a8797d0de6
lantiq: add uci-defaults code for handling leds
...
SVN-Revision: 29004
2011-11-12 23:40:21 +00:00
832e02cd77
lantiq: add /lib/lantiq.sh and make hotplug handlers use it
...
SVN-Revision: 29003
2011-11-12 23:40:16 +00:00
5dcbbf0160
lantiq: rename leds
...
SVN-Revision: 29002
2011-11-12 23:40:12 +00:00
d84b7596d9
lantiq: split compat headers out of bsp header patch
...
SVN-Revision: 29001
2011-11-12 23:40:07 +00:00
2cff80f015
lantiq: adds hotplug handler for loading rt2x00 firmware
...
SVN-Revision: 29000
2011-11-12 23:40:01 +00:00
3660c51c40
lantiq: adds hotplug handler for handling buttons and makes w303v work with it
...
SVN-Revision: 28999
2011-11-12 23:39:56 +00:00
4248705108
lantiq: cleanup default package selection
...
SVN-Revision: 28998
2011-11-12 23:39:51 +00:00
eb20ab87e6
lantiq: w303v has its rt2860 eep on the nor flash. tell compat-wireless how to use it
...
SVN-Revision: 28994
2011-11-12 18:41:15 +00:00
bbfaaeffd6
kernel: ar8216: add support for the AR8236 switch
...
SVN-Revision: 28993
2011-11-12 14:09:52 +00:00
ecb3690d0a
kernel: ar8216: move port vlan setup into a separate function
...
SVN-Revision: 28992
2011-11-12 14:09:50 +00:00
5ad763075e
ar71xx: use the button for WPS control on the DB120
...
SVN-Revision: 28990
2011-11-12 12:50:20 +00:00
4555be2bec
ar71xx: register the second ethernet interface on the DB120 board
...
SVN-Revision: 28989
2011-11-12 12:50:19 +00:00
368c6605a0
ar71xx: implement SoC specific phy interface setup
...
SVN-Revision: 28988
2011-11-12 12:50:18 +00:00
21d317b9cc
ar71xx: move phy interface setup into a separate function
...
SVN-Revision: 28987
2011-11-12 12:50:16 +00:00
aff0c84ffa
ar71xx: register both MDIO bus on the DB120 board
...
SVN-Revision: 28986
2011-11-12 12:09:59 +00:00
b144249108
ar71xx: add AR934X specific MDIO registration code
...
SVN-Revision: 28985
2011-11-12 12:09:56 +00:00
f835106c8c
ar71xx: add a secondary mdio bus
...
SVN-Revision: 28984
2011-11-12 12:09:54 +00:00
90a42da270
ar71xx: rename ar71xx_mdio_* structures to ar71xx_mdio0_*
...
SVN-Revision: 28983
2011-11-12 12:09:50 +00:00
9daa2149fd
ar71xx: add an id argument to ar71xx_add_device_mdio
...
SVN-Revision: 28982
2011-11-12 12:09:48 +00:00
b07b687aec
ar71xx: pass netdev and miidev pointer to ar71xx_add_device_dsa
...
SVN-Revision: 28981
2011-11-12 12:09:42 +00:00
a9216bb76e
ar71xx: add AR934x specific USB setup
...
SVN-Revision: 28980
2011-11-12 10:54:20 +00:00
346e44105a
ar71xx: register the first ethernet interface on the DB120 board
...
SVN-Revision: 28979
2011-11-12 10:54:18 +00:00
b1ba5e2f3d
ar71xx: allow to register ethernet interfaces for AR934X
...
SVN-Revision: 28978
2011-11-12 10:54:17 +00:00
2f9e535e89
ar71xx: ag71xx: use fixed link parameters if the mii bus is not registered
...
SVN-Revision: 28977
2011-11-12 10:54:16 +00:00
e962b07c8b
ar71xx: add AR934X specific bootstrap and reset register bits
...
SVN-Revision: 28976
2011-11-12 10:54:15 +00:00
d461fdd519
ar71xx: add diag support for the DB120 board
...
SVN-Revision: 28975
2011-11-12 10:54:10 +00:00
d8db8e94c8
ar71xx: fix GPIO direction setup for AR934x
...
SVN-Revision: 28974
2011-11-12 10:54:09 +00:00
43e993e5f5
ar71xx: fix AR934X clock frequency calculation
...
SVN-Revision: 28973
2011-11-12 10:54:08 +00:00
8687fc3e41
ar71xx: generate ubootenv from uci-defaults instead of providing defconfig
...
I noticed most of /etc/defconfig was replaced by /etc/uci-defaults, which is
indeed much nicer. So I moved over ubootenv from having a defconfig-entry to
also be generated from uci-defaults.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28971
2011-11-12 10:54:04 +00:00
fda4ee22a0
lantiq: improve falcon package selection
...
SVN-Revision: 28962
2011-11-11 21:59:11 +00:00
e1dc73be90
lantiq: fix breakage introduced in 3.1 bump
...
SVN-Revision: 28961
2011-11-11 21:59:01 +00:00
be49daffc8
base-files, target: assign name to system timeserver section, makes it easier to set servers on the cli
...
SVN-Revision: 28933
2011-11-10 12:16:41 +00:00
f53128f79b
target: linux: mtd: fix MTDREFRESH to an arbitrary high number
...
To make the ioctl number "stable", use an arbitrary high number to prevent
conflicts with new mtd ioctls that would push MTDREFRESH's number.
Also make mtd use the in-kernel mtd headers.
SVN-Revision: 28893
2011-11-09 21:16:36 +00:00
7a2efd8c28
ar71xx: remove dead code
...
SVN-Revision: 28851
2011-11-08 00:33:20 +00:00
94309039b7
ar71xx: on ar7240, exclude ports from their own port vlan destination mask
...
SVN-Revision: 28850
2011-11-08 00:33:15 +00:00
b06efd636a
kernel: add a top level menuconfig option for enabling lockdep
...
SVN-Revision: 28848
2011-11-08 00:32:57 +00:00
87704b8078
ar71xx: create TL-WA901ND network config from uci-defaults
...
SVN-Revision: 28833
2011-11-07 21:44:24 +00:00
09fdfa444f
ar71xx: create ALL0258N network config from uci-defaults
...
SVN-Revision: 28832
2011-11-07 21:44:23 +00:00
63348f5fed
ar71xx: create NBG{460N,550N,550NH} network config from uci-defaults
...
SVN-Revision: 28831
2011-11-07 21:44:20 +00:00
c3692c8331
ar71xx: create WZR-HP-G300NH network config from uci-defaults
...
SVN-Revision: 28830
2011-11-07 21:44:17 +00:00
ee1a07a11d
ar71xx: create RB-493G network config from uci-defaults
...
SVN-Revision: 28829
2011-11-07 21:44:12 +00:00
d82d063d81
ar71xx: create TL-WR1043ND network config from uci-defaults
...
SVN-Revision: 28828
2011-11-07 21:44:11 +00:00
68be590894
ar71xx: create WRT160NL network config from uci-defaults
...
SVN-Revision: 28827
2011-11-07 21:44:09 +00:00
83901e47c9
ar71xx: create PB92 network config from uci-defaults
...
SVN-Revision: 28826
2011-11-07 21:44:08 +00:00
22ab9fc9ad
ar71xx: create DIR-825-B1 network config from uci-defaults
...
SVN-Revision: 28825
2011-11-07 21:44:07 +00:00
e866ba5753
ar71xx: create TL-WR{841N-v1,941ND} network config from uci-defaults
...
SVN-Revision: 28824
2011-11-07 21:44:03 +00:00
9298c7afe5
ar71xx: create RB-450 network config from uci-defaults
...
SVN-Revision: 28823
2011-11-07 21:44:02 +00:00
ac256f97bd
ar71xx: create RB-450G, RouterStation Pro network config from uci-defaults
...
SVN-Revision: 28822
2011-11-07 21:44:01 +00:00
944ac3f6cf
ar71xx: create RB-433{,U} network config from uci defaults
...
SVN-Revision: 28821
2011-11-07 21:43:58 +00:00
6e8390ae6c
ar71xx: create even more network configs from the uci-defaults script
...
Create the default network configuration dynamically for the
AR724x/AR9331 boards. Some other boards are using the same
configuration, so convert those as well.
SVN-Revision: 28820
2011-11-07 21:43:56 +00:00
b62560413a
ar71xx: create more network configs from the uci-defaults script
...
Create the default network configuration dynamically for the boards with
swapped eth0, eth1 interfaces.
SVN-Revision: 28819
2011-11-07 21:43:54 +00:00
6c92b26bac
ar71xx: create a bunch of network configs from the uci-defaults script
...
Create the default network configuration dynamically for the boards with
a single ethernet interface.
SVN-Revision: 28818
2011-11-07 21:43:52 +00:00
0a8e5dbf7b
ar71xx: create generic network config from an uci-defaults script
...
SVN-Revision: 28817
2011-11-07 21:43:51 +00:00
54c034ae7a
ar71xx: remove AP81 defconfig, it is the same as the generic config
...
SVN-Revision: 28816
2011-11-07 21:34:33 +00:00
5b6cc3eb9f
ar71xx: change generated Buffalo firmware versions
...
With version 1.76 the upgrade may fail with newer Buffalo firmwares with
a message like this:
"You can not update the firmware because the firmware version is earlier
than 1.82. Please use 1.82 or later version for firmware update."
SVN-Revision: 28815
2011-11-07 21:34:32 +00:00
cc2cf8f3d5
update 3.1 patches
...
SVN-Revision: 28814
2011-11-07 21:13:13 +00:00
c4bc2552a3
update arm mach-types
...
SVN-Revision: 28813
2011-11-07 21:12:26 +00:00
eb9ef60e2d
ar71xx: enable sysupgrade on the WHR-G301N and WHR-HP-GN boards
...
SVN-Revision: 28812
2011-11-07 20:25:00 +00:00
8456840d82
ar71xx: wrap long lines in the upgrade script
...
SVN-Revision: 28811
2011-11-07 20:24:59 +00:00
c60baf78ce
ar71xx: fix WHR-HP-G300N firmware partition offset
...
SVN-Revision: 28810
2011-11-07 20:24:57 +00:00
b27254a2c5
ar71xx: add default network configuration for the WHR-HP-GN
...
SVN-Revision: 28807
2011-11-07 13:32:43 +00:00
034b2b7cde
ar71xx: build image for the Buffalo WHR-HP-GN
...
SVN-Revision: 28806
2011-11-07 12:59:11 +00:00
a801d620a7
ar71xx: add support for the Buffalo WHR-HP-GN board
...
SVN-Revision: 28805
2011-11-07 12:59:10 +00:00
0d9ae0a036
ar71xx: build image for the Buffalo WHR-G301N
...
SVN-Revision: 28804
2011-11-07 12:59:08 +00:00
4509af17ed
ar71xx: add support for the Buffalo WHR-G301N board
...
SVN-Revision: 28803
2011-11-07 12:59:07 +00:00
63784ea2bc
ar71xx: fix WHR-HP-G300N image generation
...
SVN-Revision: 28802
2011-11-07 12:59:05 +00:00
b3b21cb3bf
ar71xx: enable WHR-HP-G300N support in kernel config
...
SVN-Revision: 28801
2011-11-07 12:59:04 +00:00
4aace1e2e3
ar71xx: fix WHR-HP-G300N MTD partitions
...
SVN-Revision: 28800
2011-11-07 12:59:03 +00:00
05ce57c005
omap24xx: Add cbus tahvo locking fix.
...
SVN-Revision: 28767
2011-11-05 16:10:18 +00:00
6288ac7ed4
omap24xx: Fix n810bm compilation
...
SVN-Revision: 28766
2011-11-05 16:01:53 +00:00
297ac9a7f1
kernel: swconfig: add a missing unlock in error path
...
SVN-Revision: 28753
2011-11-04 14:38:31 +00:00
d6f02b62d4
add timeserver config to target specific system configs as well
...
SVN-Revision: 28750
2011-11-04 12:53:35 +00:00
82bd0a43f1
kernel: merge regression fixes for the netfilter patches to the 3.1 kernel patches (patch by tripolar)
...
SVN-Revision: 28734
2011-11-03 20:02:31 +00:00
95d36d3efe
lantiq: remove obseleted folder. we use 3.1 now
...
SVN-Revision: 28728
2011-11-03 16:33:27 +00:00
ea36ad76bc
lantiq: bump to 3.1
...
SVN-Revision: 28721
2011-11-03 15:15:52 +00:00
4c985724af
ar71xx: add missing AR71XX_MACH_TL_WR741ND_V4
...
SVN-Revision: 28709
2011-11-01 14:38:12 +00:00
fc8adbb854
ar71xx: build image for the TL-WR741ND v4 board
...
SVN-Revision: 28708
2011-11-01 11:20:55 +00:00
91f08d47c2
ar71xx: add initial support for the TL-WR741ND v4 board
...
The ethernet port LEDs are not working yet.
SVN-Revision: 28706
2011-11-01 11:20:52 +00:00
21e651c9a1
ar71xx: add AR933X GMAC register defines
...
SVN-Revision: 28705
2011-11-01 11:20:50 +00:00
43e2e2e4ef
ar71xx: combine LEDs setup in one file
...
SVN-Revision: 28704
2011-11-01 11:20:49 +00:00
f372620ffa
ar71xx: unify LED names on Planex boards
...
SVN-Revision: 28703
2011-11-01 11:20:47 +00:00
66ab406d5a
ar71xx: unify LED names on Buffalo boards
...
SVN-Revision: 28702
2011-11-01 11:20:46 +00:00
e7586959df
ar71xx: unify LED names on TP-Link boards
...
SVN-Revision: 28701
2011-11-01 11:20:44 +00:00
3a7b12a27d
ar71xx/all0258n: sysupgrade support
...
U-Boot on the ALL0258N needs offset, size and md5 for kernel and rootfs to be
stored in the U-Boot environment.
If the checksums don't match during boot, a failsafe-system is booted instead.
This patch adds a board-specific sysupgrade hack for the all0258n which
calculates and updates the checksums for the U-Boot environment.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28700
2011-11-01 09:23:32 +00:00
f40557a692
ar71xx/all0258n: add default config
...
This adds default network and uboot-env settings for the ALL0258N.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28699
2011-11-01 09:23:31 +00:00
06d9653b36
ar71xx: remove default network config of the mzk-w04nu board as well
...
It works with the generic config.
SVN-Revision: 28695
2011-11-01 09:23:25 +00:00
693c777eaf
ar71xx: remove LED setup of nonexistent interfaces on RB750
...
SVN-Revision: 28693
2011-10-31 14:26:56 +00:00
2bcd612e72
ar71xx: remove default network config of the wnr2000 board
...
It is the same as the generic configuration.
SVN-Revision: 28692
2011-10-31 14:26:51 +00:00
17ccd4aec4
rt305x: Create factory image for Fonera 2.0n
...
SVN-Revision: 28689
2011-10-31 09:23:44 +00:00
29958120a2
omap24xx: Default to linux-3.1
...
SVN-Revision: 28687
2011-10-30 22:42:00 +00:00
c00fd42353
omap24xx: Fix n810 LCD initialization
...
SVN-Revision: 28685
2011-10-30 20:31:45 +00:00
f37c24d35f
omap24xx: Fix n810 boot
...
SVN-Revision: 28683
2011-10-30 18:46:45 +00:00
39b3bfcf6a
ar71xx/sysupgrade: use $magic_long instead of $magic when comparing with a 32-bit value
...
Aparently $magic_long was meant here instead of $magic when comparing with
32-bit values.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28678
2011-10-30 13:06:30 +00:00
fd0e6e1452
omap24xx: Refresh 3.1 config
...
SVN-Revision: 28677
2011-10-29 22:52:44 +00:00
ba9ee13744
omap24xx: Refresh 3.1 patches
...
SVN-Revision: 28676
2011-10-29 22:52:07 +00:00
e184bfe6f0
Fix tusb patch
...
SVN-Revision: 28675
2011-10-29 22:33:59 +00:00
a3db2f2055
omap24xx: Fix MUSB compile
...
SVN-Revision: 28674
2011-10-29 22:26:27 +00:00
5dde93038f
omap24xx: Add n800 touchscreen and keypad drivers. Thanks to Marat Radchenko.
...
SVN-Revision: 28673
2011-10-29 20:35:36 +00:00
7d123a86e3
omap24xx: Add 3.1 patchset.
...
SVN-Revision: 28672
2011-10-29 19:02:50 +00:00
415814f051
ar71xx: fix typos in image/Makefile
...
SVN-Revision: 28618
2011-10-27 07:54:52 +00:00
1646346798
ar71xx: add initial support for the OpenMesh OM2P board
...
Based on a patch by Marek Lindner <marek@open-mesh.com>
SVN-Revision: 28617
2011-10-27 07:54:51 +00:00
d02f22fea1
ar71xx/all0258n: fix partition layout
...
A miscalculation in the original patch makes OpenWrt destroy the failsafe image.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28615
2011-10-27 07:54:47 +00:00
f15f6bc76f
Update my email address
...
SVN-Revision: 28603
2011-10-26 14:54:26 +00:00
b17bfe4f68
x86: disable crashlog, ioremap of RAM does not work properly here
...
SVN-Revision: 28599
2011-10-26 11:49:25 +00:00
4a70cace09
ar71xx: create image for the WNDR3800
...
This adds support for the Netgear WNDR3800, it is almost the same as
the WNDR3700v2. It just has more RAM so the hd_id had to be adjusted.
Signed-off-by: Petri Rosenström <petri.rosenstrom@gmail.com>
SVN-Revision: 28597
2011-10-26 06:12:47 +00:00
3d1d93cb0c
target: remove CONFIG_IDE_PROC_FS support as well
...
SVN-Revision: 28586
2011-10-25 16:40:06 +00:00
de7cae82e9
brcm47xx: revert accidentially added EARLY_PRINTK symbol from previous commit
...
SVN-Revision: 28585
2011-10-25 16:19:52 +00:00
a9e64493d8
target: globally disable BSD process accounting
...
SVN-Revision: 28584
2011-10-25 16:18:36 +00:00
ee8077f0fe
ramips: Support for NexAira BC2
...
The preconfiguration of the USB LED has benn move to the
/etc/uci-defaults/leds script. [juhosg]
Signed-off-by: Adam Porter <porter.adam at gmail.com>
SVN-Revision: 28571
2011-10-24 21:49:36 +00:00
18452a753b
ramips: fix switch-port assignment for HW550-3G
...
WAN is on swtich port 0 for Aztech HW550-3G.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28570
2011-10-24 21:49:32 +00:00
68a01c0180
ramips: combine led setup for all boards in one file
...
This removes unnecessary duplication and simplifies led setup for new
boards. It would be a one line change most likely.
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
SVN-Revision: 28569
2011-10-24 21:49:31 +00:00
c8b9086ac5
ar71xx: build image for the Buffalo WHR-HP-G300N
...
Based on a patch by Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 28568
2011-10-24 21:49:29 +00:00
9d51cda2db
ar71xx: Buffalo WHR-HP-G300N kernel support
...
The initial support for the Buffalo WHR-HP-G300N box.
The code was confirmed to boot and run, but not tested in depth.
Known problem: iw phy phy0 info shows:
Coverage class: 0 (up to 0m)
Available Antennas: TX 0 RX 0
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 28567
2011-10-24 21:49:26 +00:00
0ab6be2ba3
ar71xx: build image for the Allnet ALL0258N board
...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28565
2011-10-24 21:49:23 +00:00
d96e321bd1
ar71xx: add kernel support for the Allnet ALL0258N board
...
This patchs adds support for the Allnet ALL0258N outdoor AP/bridge.
The ALL0258N is based on the AR7240 SoC paired with an AR9285 radio,
it got 8MB of NOR and 32MB SDRAM.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28564
2011-10-24 21:49:21 +00:00
ef41e0a61c
ar71xx: don't override CONFIG_FSNOTIFY
...
SVN-Revision: 28563
2011-10-24 21:49:18 +00:00
b61de9c865
base-files: make sure inittab-console-fixup returns with success ( #10275 )
...
SVN-Revision: 28562
2011-10-24 21:35:43 +00:00
b0d9bccafc
x86: allow VDI & VMDK images for all subtargets ( closes : #10255 )
...
SVN-Revision: 28518
2011-10-22 13:09:15 +00:00
40d088446f
linux: generic: refresh patches for 3.1-rc10
...
Hopefully the last one and identical to final.
SVN-Revision: 28492
2011-10-20 10:32:44 +00:00
a136b67604
linux: ar71xx: add support for Mikrotik Routerboard RB493G
...
SVN-Revision: 28423
2011-10-11 23:05:16 +00:00
03f91068d1
ar71xx: add a workaround for ar8316 not always driving the TA bit to low
...
AR8316 behind a GPIO bitbanged MDIO bus fails to drive the turnaround bit
to low despite returning a valid value. Ignore it and just use the
returned value anyway.
SVN-Revision: 28422
2011-10-11 23:05:13 +00:00
b7a2a74823
ar8216: use mdiobus_{read,write} to ensure proper locking
...
SVN-Revision: 28421
2011-10-11 23:05:10 +00:00
0a866293bd
* update patches to 3.0
...
* add basic vr9 support
* backport 3.1 fixes
* backport 3.2 queue (falcon)
SVN-Revision: 28405
2011-10-10 15:13:46 +00:00
c674c874b7
ag71xx: close a race between the phy state machine and link state
...
A fast stop/start cycle could leave the ag71xx interrupts and tx engine
disabled when using a phy driver with a fixed link and the start/stop
happens between two phy state machine polls.
Prevent this by always forcing the link down on stop regardless of phy
state and having a phy connected.
SVN-Revision: 28380
2011-10-08 11:37:14 +00:00
ce5e1abbb7
add IDs for Huawai K3770, K3771, K4510 and K4511 to option driver
...
SVN-Revision: 28376
2011-10-06 18:23:16 +00:00
829ae01f16
add missing kernel config symbols
...
SVN-Revision: 28363
2011-10-04 09:15:37 +00:00
b0345ef184
Was specifying input-polled-keys and not input-keys-polled as the module name. Philip Prindeville - 2011-10-03 03:58:17
...
SVN-Revision: 28357
2011-10-03 04:39:54 +00:00
c0a625ffbf
Add patch for linux-3.0 as well.
...
Fix typo from previous submission with input-keys-polled.
Philip Prindeville - 2011-10-03 01:44:55
SVN-Revision: 28356
2011-10-03 03:09:20 +00:00
7e372b6dcf
New x86 platform specific symbol needed for 3.1-rc3.
2011-10-03 03:06:29 +00:00
541aa8e38e
A lot of these options get set automatically when Geode is selected.
...
Don't make the config more complicated than it needs to be.
Philip Prindeville - 2011-08-29 03:15:27
SVN-Revision: 28353
2011-10-03 03:02:42 +00:00
3802769ea1
add vlan definitions for Siemens SE505v2
...
Hi,
this patch adds the correct vlan definitions for the Siemens SE505v2. It
applies to trunk as well as backfire (please apply here too). On
backfire this also patches brcm-2,4, because brcm47xx base-files is just
symlinked to brcm-2.4.
It also fixes two whitespace issues.
Tested with brcm47xx on both trunk and backfire branch and works as
expected.
Signed-off-by: Manuel Munz <freifunk@somakoma.de>
SVN-Revision: 28336
2011-09-30 12:55:33 +00:00
aecc73de77
The enable function was using the global timeout variable for local operations. This resulted in the value of the global variable being corrupted, thus breaking the code.
...
SVN-Revision: 28310
2011-09-26 10:35:51 +00:00
1ef8066bff
* remove obseleted m25p80 patch
...
SVN-Revision: 28309
2011-09-26 09:36:02 +00:00
cf59e7255d
* rebase 3.0 patches * fold some fixes into existing patches
...
SVN-Revision: 28308
2011-09-26 09:35:02 +00:00
6ac4156136
ar71xx: fix MAC addresses on the DIR-825-B1 board
...
Patch-by: Lukas Kuna
SVN-Revision: 28295
2011-09-23 19:56:39 +00:00
e45d7d7006
ar71xx: enable login only on the system console by default
...
SVN-Revision: 28294
2011-09-23 19:56:38 +00:00
5fc14dfb87
linux/generic: commit an upstream kernel 3.0 patch (fixes busubox-1.19.2 build failure)
...
SVN-Revision: 28293
2011-09-23 10:00:13 +00:00
49ac36e818
ar71xx: build images for the TP-Link TL-WR703N v1 board
...
Based on a patch by dongyuqi <729650915@qq.com>
SVN-Revision: 28279
2011-09-21 11:47:56 +00:00
733399600f
ar71xx: add support for the TP-Link TL-WR703N v1 board
...
Based on a patch by dongyuqi <729650915@qq.com>
SVN-Revision: 28277
2011-09-21 11:47:53 +00:00
d3617ac7d3
ar71xx: add AR933x specific USB setup function
...
SVN-Revision: 28276
2011-09-21 11:47:51 +00:00
91340d8af7
ar71xx: add ar71xx_device_reset_rmw helper
...
SVN-Revision: 28275
2011-09-21 11:47:50 +00:00
9fa51d5c38
ar71xx: fix copy&paste bug in WZRHPAG300H profile description
...
SVN-Revision: 28274
2011-09-21 11:47:48 +00:00
079e746fc4
ar71xx: remove 'default [yn]' from machine Kconfig entries
...
SVN-Revision: 28273
2011-09-21 11:47:47 +00:00
73dac07c44
ar71xx: sort AR71XX_MACH_* entries
...
SVN-Revision: 28272
2011-09-21 11:47:45 +00:00
ef2431c8d9
ar71xx: create image for the TP-Link TL-WR743ND v1
...
Same hardware as WR741ND but with PoE support.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 28271
2011-09-21 11:47:44 +00:00
76d0d1a837
ar71xx: create image for the TP-Link TL-WR740N v3
...
Signed-off-by: Martin Raykov <martin.raykov@gmail.com>
SVN-Revision: 28269
2011-09-21 11:47:40 +00:00
93c093057d
generic: jumbo frames support for rtl8366s
...
This patch adds the option to enable jumbo frames on the rtl8366s
switch. This is almost exactly the same as the first patch at
https://dev.openwrt.org/ticket/7977 and it has been requested
in a comment there.
I have tested this and it successfully allows devices on the switch
using jumbo frames to communicate.
Signed-off-by: Ash Hughes <ashley.hughes@blueyonder.co.uk>
SVN-Revision: 28267
2011-09-21 11:47:38 +00:00
1bdf65f580
ar71xx: fix register range check for DMA stuck checks (thx, Frédéric Moulins)
...
SVN-Revision: 28213
2011-09-11 17:44:12 +00:00
ba46c7b3c6
Xen DomU: make sure kernel is gzip compressed, pygrub cannot handle xz
...
SVN-Revision: 28197
2011-09-08 22:18:26 +00:00
65d809ef19
ar71xx: do not count normal interrupts as spurious ( fixes #10037 )
...
SVN-Revision: 28182
2011-09-06 05:38:23 +00:00
de8cabe839
ar71xx: clean up profiles, put in kmod-ath9k and wpad-mini by default ( fixes #9954 )
...
SVN-Revision: 28173
2011-09-05 18:37:48 +00:00
ed2c8bdc92
upgrade testing kernel support to 3.1
...
SVN-Revision: 28165
2011-09-04 15:06:05 +00:00
4f0b1a6602
cleanup config
...
SVN-Revision: 28164
2011-09-04 15:02:37 +00:00
0569cff6e1
refresh patches
...
SVN-Revision: 28163
2011-09-04 15:01:56 +00:00
6d17e13cde
add missing symbols
...
SVN-Revision: 28162
2011-09-04 15:01:25 +00:00
24dfe525c2
brcm47xx: fix padding of trx images, padjffs2 does not work properly on empty files by default
...
SVN-Revision: 28125
2011-08-29 21:23:51 +00:00
cd2c68501c
ar71xx: fix ethernet PLL setting on ar7242
...
SVN-Revision: 28124
2011-08-29 21:23:46 +00:00
cc037a5e27
Remove subpage align patch
...
SVN-Revision: 28086
2011-08-25 11:49:55 +00:00
21f7943561
Re-order patches, add nand sub-page alignment
...
SVN-Revision: 28084
2011-08-25 10:37:30 +00:00
cbd28ad0ec
bump to 2.6.39.4
...
Since linux gets developed on x86 more than all other hardware,
hardly makes sense to have our default x86 version be trailing
by over a year.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 28082
2011-08-25 09:35:51 +00:00
d2652dee9d
update alix2 platform driver
...
Add support for Ed Wildgoose's alix platform driver plus my
enhancement to add GPIO soft button support.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 28081
2011-08-25 09:35:45 +00:00
71adaae258
kernel: add two missing config symbols for 3.1
...
SVN-Revision: 28080
2011-08-24 11:43:25 +00:00
72e117ec79
ramips: rt305x: add support for the ZyXEL NBG-419N board
...
SVN-Revision: 28078
2011-08-22 20:41:49 +00:00
4b96d3af2a
ramips: rt305x: remove unused defines from mach-nw718.c
...
SVN-Revision: 28077
2011-08-22 20:41:48 +00:00
462ca22e9c
ramips: sort Makefile entries
...
SVN-Revision: 28076
2011-08-22 20:41:47 +00:00
d50494f3bb
ramips: sort RAMIPS_MACH_* defines
...
SVN-Revision: 28075
2011-08-22 20:41:45 +00:00
90686691ce
ramips: fix wireless firmware extraction for wr512-3gn
...
Signed-off-by: Andrew Andrianov <necromant@necromant.ath.cx>
SVN-Revision: 28073
2011-08-22 18:08:45 +00:00
f0049824b9
ramips: remove 'default [yn]' keywords from machine Kconfig entries
...
SVN-Revision: 28054
2011-08-19 15:55:12 +00:00
6720025497
ramips: rt305x: fix wr512n image generation
...
SVN-Revision: 28053
2011-08-19 15:55:11 +00:00
9085b05d9e
ramips: rt305x: support for wr512-3gn-like routers
...
Signed-off-by: Andrew Andrianov <necromant@necromant.ath.cx>
SVN-Revision: 28052
2011-08-19 15:55:10 +00:00
46b101ad0a
ramips: register usb on Belkin F5D8235 v2 and Argus ATP-52-B routers
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 28051
2011-08-19 15:55:08 +00:00
05209860da
ramips: fix wireless on Belkin F5D8235 v2
...
Fix wireless firmware extract from flash for Belkin F5D8235 v2.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 28050
2011-08-19 15:55:07 +00:00
f8ab604eb6
ramips: fix typo in default packages
...
Fix fivebytepypo - there is no such kernel module wpad-mini :)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 28049
2011-08-19 15:55:05 +00:00
048d4aca76
omap35xx: Add 3.0.3 kernel support for Gumstix
...
SVN-Revision: 28047
2011-08-19 12:00:08 +00:00
464539b074
kernel: update to version 3.0.3
...
SVN-Revision: 28043
2011-08-18 12:54:12 +00:00
ebb152295b
fix the default network configuration for the ASUS WL-330gE ( #8751 )
...
SVN-Revision: 28024
2011-08-17 03:16:59 +00:00
09b1073f9b
kernel: update kernel to version 2.6.39.4
...
SVN-Revision: 28022
2011-08-16 22:04:10 +00:00
3e94ee9642
kernel: generic: refresh patches for 3.1-rc2
...
SVN-Revision: 28021
2011-08-16 21:42:15 +00:00
ace8ce0845
ramips: use maccalc instead of hexdump + sed
...
SVN-Revision: 28007
2011-08-15 19:00:23 +00:00
bfc47ffead
ramips: rt305x: fix mac addresses on the Netcore NW718 board
...
SVN-Revision: 28006
2011-08-15 18:55:53 +00:00
17c041cd0b
ramips: add maccalc to the default package list
...
SVN-Revision: 28005
2011-08-15 18:55:52 +00:00
67e480971c
ramips: add input drivers to the default package list
...
SVN-Revision: 28003
2011-08-15 18:55:50 +00:00
35ecf12059
ramips: rt305x: make config and factory partitions read-only on the ATP-52B
...
SVN-Revision: 28002
2011-08-15 18:55:48 +00:00
75e2360ab3
ramips: add uci-defaults scripts to preconfigure USB LEDs
...
SVN-Revision: 28000
2011-08-15 14:12:00 +00:00
e1b176de82
ramips: rt305x: add some USB modules to the default profile
...
SVN-Revision: 27999
2011-08-15 14:11:58 +00:00
169d68c98c
ramips: rt305x: add dwc_otg driver
...
Based on a patch by Layne Edwards <ledwards@astrumtech.net>
SVN-Revision: 27997
2011-08-15 14:11:55 +00:00
0ca16a4600
ramips: rt305x: register the dwc_otg device on the relevant boards
...
SVN-Revision: 27996
2011-08-15 14:11:52 +00:00
addc86fdbd
ramips: rt305x: add dwc_otg platform device
...
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
SVN-Revision: 27995
2011-08-15 14:11:51 +00:00
6ef87ff5e6
ramips: sync kernel config
...
SVN-Revision: 27993
2011-08-15 14:11:48 +00:00
4ee4fc9725
ramips: load the input drivers during preinit
...
SVN-Revision: 27992
2011-08-15 14:11:47 +00:00
a3c7e71ae1
ramips: add support for Argus ATP-52B
...
[The ESW related changes has been removed - juhosg]
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 27991
2011-08-15 14:11:45 +00:00
1ebcf03789
ramips: allow to specify port layout for the switch of the RT305x/RT3350
...
Based on a patch by Roman Yeryomin <roman@advem.lv>
SVN-Revision: 27990
2011-08-15 14:11:43 +00:00
bb64fb2e58
generic: ar8216: add support for get link status
...
SVN-Revision: 27989
2011-08-15 14:11:41 +00:00
50817f6afe
kernel: disable cfi cmdset 0002 erase suspend
...
on some platforms, erase suspend leads to data corruption and lockups when write
ops collide with erase ops. this has been observed on the buffalo wzr-hp-g300nh.
rather than play whack-a-mole with a hard to reproduce issue on a variety of devices,
simply disable erase suspend, as it will usually not produce any useful gain on
the small filesystems used on embedded hardware.
SVN-Revision: 27984
2011-08-15 00:15:36 +00:00
12c84f8eeb
ar71xx: add some code to detect DMA stuck conditions on ar7240
...
SVN-Revision: 27975
2011-08-13 22:30:14 +00:00
85ccc74e1b
ar71xx: on ar724x only reset the link status in the restart handler, the fast reset takes care of DMA stuck issues
...
SVN-Revision: 27973
2011-08-13 21:49:46 +00:00
77218b0338
brcm47xx: fix flash detection on chipcommon less devices.
...
This closes #9906
Thank you for the report Kim
SVN-Revision: 27967
2011-08-12 16:37:22 +00:00
82a05d1a19
initramfs: allow preinit to enable switching from initramfs to tmpfs to allow overlayfs to be mounted on top of it
...
SVN-Revision: 27960
2011-08-11 20:32:57 +00:00
d26bb6c59c
ar71xx: adjust the mtd layout of tew-632brp and dir-615c to match the image layout ( fixes #9922 )
...
SVN-Revision: 27959
2011-08-11 13:52:40 +00:00
ce2ced7311
package more board specific modules:
...
- keyboard matrix driver
- SoC sound support
based on patch by KanjiMonster
SVN-Revision: 27957
2011-08-11 11:18:44 +00:00
f7dbf2ef04
add more missing touchscren symbols (3.0+)
...
SVN-Revision: 27956
2011-08-11 11:18:41 +00:00
11b1f687d4
disable hardware perf support to work in qemu
...
SVN-Revision: 27955
2011-08-11 11:18:37 +00:00
20de21593b
kernel: revert r27953
...
KanjiMonster did the right patch, I was just confused because of linux-3.0 and linux-2.6.30
SVN-Revision: 27954
2011-08-11 09:54:02 +00:00
409f8211e1
kernel: fix ocf patch for kernel 2.6.30
...
find_task_by_vpid is already exported by the kernel without any patches needed.
SVN-Revision: 27953
2011-08-11 09:47:36 +00:00
7304dcad2a
kernel: 2.6.30: remove bogus additional find_task_by_vpid export from OCF
...
find_task_by_vpid is already exported, thus breaking builds.
SVN-Revision: 27952
2011-08-11 09:46:30 +00:00
def60e2918
ar71xx: make ehci patch apply again
...
SVN-Revision: 27951
2011-08-10 23:02:56 +00:00
9e5ead9a51
ar71xx: fix a copy&paste bug that broke wzr-hp-g300nh and wzr-hp-ag300h images ( #9918 )
...
SVN-Revision: 27950
2011-08-10 22:24:56 +00:00
b59ab7d13b
fix ehci build on 3.0+
...
SVN-Revision: 27946
2011-08-10 11:37:25 +00:00
0e40c19b45
add ignore_oc in struct ehci_hcd
...
SVN-Revision: 27945
2011-08-10 11:37:21 +00:00
458716389c
update to 3.0.1
...
SVN-Revision: 27943
2011-08-09 13:13:22 +00:00
f124358722
add CONFIG_EARLY_PRINTK
...
SVN-Revision: 27942
2011-08-09 13:13:16 +00:00
6b5f483efa
bcm63xx: add support for linux 3.1-rc1
...
SVN-Revision: 27941
2011-08-09 12:19:49 +00:00
cf2070bd5b
linux: generic: add support for 3.1-rc1
...
SVN-Revision: 27940
2011-08-09 12:19:43 +00:00
7ef004a144
Add packages that will be relant as "There's a new Alix platform driver hitting linux-next upstream. Get ready for it in 2.6.39.4 and 3.0.
...
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>"
SVN-Revision: 27929
2011-08-08 02:33:18 +00:00
ba9e7889dd
kernel: fix another typo in the netfilter optimization patches
...
SVN-Revision: 27927
2011-08-07 21:17:18 +00:00
6f4151b7f0
kernel: add missing option
...
SVN-Revision: 27925
2011-08-06 16:46:04 +00:00
ac96ae6731
kernel: add missing checks in the netfilter optimization patch which broke some rules containing only source/destination address checks
...
SVN-Revision: 27923
2011-08-06 12:39:31 +00:00
John Crispin
Gabor Juhos
Florian Fainelli
Hauke Mehrtens
Imre Kaloz
Felix Fietkau
Jo-Philipp Wich
Vasilis Tsiligiannis
Jonas Gorski
Daniel Dickinson
Nicolas Thill
Michael Büsch
Alexandros C. Couloumbis
Hamish Guthrie