60d5abbc27
ar71xx: ag71xx: make ring sizes configurable via ethtool
...
SVN-Revision: 27041
2011-05-31 22:53:10 +00:00
7a2651f633
ar71xx: ag71xx: prepare to make ring sizes configurable
...
SVN-Revision: 27040
2011-05-31 22:53:09 +00:00
669aba3871
ar71xx: ag71xx: nuke unused AG71XX_TX_FIFO_LEN define
...
Reported-by: Dave Täht <dave.taht@gmail.com>
SVN-Revision: 27039
2011-05-31 22:53:07 +00:00
2b5402d128
ar71xx: only enable the rx engine after the link is up, fixes a race condition that got rx stuck when the interface is brought up during lots of inbound traffic (thx, matteo)
...
SVN-Revision: 27035
2011-05-30 23:08:01 +00:00
0ebc93831f
ar71xx: disable flow control for ar724x, it can get stuck in a loop of continously sending MAC pause frames
...
SVN-Revision: 27034
2011-05-30 23:07:57 +00:00
17e257925f
ar71xx: don't probe the LAN PHY
...
SVN-Revision: 26924
2011-05-17 11:15:24 +00:00
4deecea26b
ar71xx: detect link on LAN ports
...
SVN-Revision: 26922
2011-05-17 11:12:56 +00:00
2ea528d1d0
ar71xx: add link detection on Ubiquiti devices WAN port
...
SVN-Revision: 26891
2011-05-14 23:31:50 +00:00
c0c2e18452
use correct macros and frame size in ag71xx
...
SVN-Revision: 26890
2011-05-14 23:10:06 +00:00
99d1d4f795
ar71xx: cosmetic fixes
...
SVN-Revision: 26889
2011-05-14 23:08:00 +00:00
9b5036a29d
ar71xx: populate LED3 on the JA76PF board
...
Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>
SVN-Revision: 26862
2011-05-08 21:38:51 +00:00
869f3cb718
ar71xx: remove superfluous fifo_cfg overrides
...
SVN-Revision: 26859
2011-05-08 21:38:46 +00:00
5d77f370d6
ar71xx: ag71xx: make switch register access atomic
...
Reading of the PHY registers occasionally returns with bogus values
under heavy load. This misleads the PHY driver and thus causes false
link/speed change notifications which leads to performance loss.
This is easily noticable during an iperf session:
...
[ 3] 52.0-53.0 sec 11.3 MBytes 94.4 Mbits/sec
[ 3] 53.0-54.0 sec 11.4 MBytes 95.4 Mbits/sec
eth1: link down
br-lan: port 2(eth1) entering forwarding state
eth1: link up (100Mbps/Full duplex)
br-lan: port 2(eth1) entering forwarding state
br-lan: port 2(eth1) entering forwarding state
[ 3] 54.0-55.0 sec 6.75 MBytes 56.6 Mbits/sec
[ 3] 55.0-56.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 56.0-57.0 sec 10.5 MBytes 88.1 Mbits/sec
...
[ 3] 169.0-170.0 sec 11.4 MBytes 95.4 Mbits/sec
[ 3] 170.0-171.0 sec 11.4 MBytes 95.4 Mbits/sec
eth1: link up (10Mbps/Half duplex)
[ 3] 171.0-172.0 sec 7.63 MBytes 64.0 Mbits/sec
[ 3] 172.0-173.0 sec 9.38 MBytes 78.6 Mbits/sec
eth1: link up (100Mbps/Full duplex)
[ 3] 173.0-174.0 sec 11.3 MBytes 94.4 Mbits/sec
[ 3] 174.0-175.0 sec 11.4 MBytes 95.4 Mbits/sec
SVN-Revision: 26856
2011-05-08 16:32:53 +00:00
3711658281
ar71xx: ag71xx: fix section mismatch warnings
...
The function __devinit ag71xx_probe() references
a function __devexit ag71xx_phy_disconnect().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
ag71xx_phy_disconnect() so it may be used outside an exit section.
The function ag71xx_phy_disconnect() references a function in an exit
section.
Often the function ag71xx_ar7240_cleanup() has valid usage outside the
exit section
and the fix is to remove the __devexit annotation of
ag71xx_ar7240_cleanup.
SVN-Revision: 26855
2011-05-08 13:30:36 +00:00
ef53029870
ar71xx: ag71xx: fix build error if debugfs is enabled
...
SVN-Revision: 26854
2011-05-08 13:30:26 +00:00
8b67d748cb
ar71xx: ag71xx: add debugfs entry for [rt]x_ring
...
SVN-Revision: 26845
2011-05-07 12:40:34 +00:00
2166432ba0
ar71xx: ag71xx: add timestamps to ag71xx_buf
...
SVN-Revision: 26844
2011-05-07 12:40:28 +00:00
896e1d1ab4
ar71xx: ag71xx: use dynamically allocated buffer for napi_stats
...
SVN-Revision: 26843
2011-05-07 12:40:26 +00:00
a6708d20d1
ar71xx: ag71xx: use debugfs_remove_recursive
...
SVN-Revision: 26842
2011-05-07 12:40:25 +00:00
c39e5b9360
ar71xx: override wmac device name for the AR934x SoCs
...
SVN-Revision: 26840
2011-05-07 09:23:32 +00:00
cbc75a9c70
ar71xx: use the ar8316 switch driver on the PB92 board and add a matching default network config
...
SVN-Revision: 26779
2011-04-28 21:27:42 +00:00
36aecb08b8
ar71xx: fix MDIO access on ar7242 (based on a patch by Jess Zhu)
...
SVN-Revision: 26777
2011-04-28 19:30:49 +00:00
fa9f45f345
ar71xx: fix build error w/o CONFIG_PCI
...
SVN-Revision: 26606
2011-04-12 13:14:56 +00:00
e193547733
ar71xx: use the gpio_keys_polled driver instead of gpio_buttons
...
SVN-Revision: 26603
2011-04-12 09:29:21 +00:00
54ede24829
ar71xx: Add support for WZR-HP-G301NH
...
Add support for the Buffalo WZR-HP-G301NH. The only difference between it
and the WZR-HP-G00NH is that it has a RTL8366RB instead of a RTL8366S.
Since we don't do runtime detection of the switch, we need a separate
machine definition for it.
While we are at it, also rename the profile to reflect that it now is for
more than one device.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26601
2011-04-12 09:29:10 +00:00
ef4c1d49a6
ar71xx: merge dev-ar9{13,34}x-wmac into dev-ar9xxx-wmac
...
SVN-Revision: 26595
2011-04-11 17:37:08 +00:00
4711dea8ff
ar71xx: fix AR934X_WMAC_SIZE
...
SVN-Revision: 26594
2011-04-11 17:37:03 +00:00
8586e61b00
ar71xx: fix section mismatch
...
SVN-Revision: 26562
2011-04-09 18:47:55 +00:00
a8bf5e3cdb
ar71xx: rename ar934x_ref_freq to ar71xx_ref_freq
...
Also initialize that for each SoC and print its value along with the
other frequencies.
SVN-Revision: 26561
2011-04-09 18:47:52 +00:00
5573d6eb28
ar71xx: show the SoC type earlier
...
SVN-Revision: 26560
2011-04-09 18:47:50 +00:00
ab4c3b3a1c
ar71xx: cleanup SoC detection code
...
SVN-Revision: 26559
2011-04-09 18:47:49 +00:00
3310c70702
ar71xx: Fix mac address offset for AR934x
...
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
SVN-Revision: 26557
2011-04-09 18:47:42 +00:00
8f889f9250
ar71xx: add DB120 board specific PCI initialization
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26523
2011-04-07 20:53:41 +00:00
a0c3d49064
ar71xx: register WMAC device on the DB120 board
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26522
2011-04-07 20:53:37 +00:00
428888faec
ar71xx: add support for the built-in WMAC of the AR934x
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26521
2011-04-07 20:53:34 +00:00
14b42c44ec
ar71xx: add initial support for the Atheros DB120 board
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26518
2011-04-07 20:53:19 +00:00
2b064bb398
ar71xx: add support for the watchdog of the AR934x SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26516
2011-04-07 20:53:10 +00:00
e4555809c7
ar71xx: enable PCI for the AR934[24] SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26515
2011-04-07 20:53:05 +00:00
4f395745af
ar71xx: enable USB support for the AR934x SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26514
2011-04-07 20:53:03 +00:00
25693b4769
ar71xx: enable GPIO support for the AR934x SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26513
2011-04-07 20:53:00 +00:00
334a5ec36e
ar71xx: add AR934x specific glue for ar7100_device{start,stop}
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26512
2011-04-07 20:52:57 +00:00
ccd3ebd309
ar71xx: add AR934x specific UART clock initialization
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26511
2011-04-07 20:52:53 +00:00
91470edada
ar71xx: add AR934x specific glue for IRQ initialization
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26510
2011-04-07 20:52:49 +00:00
3b209880bc
ar71xx: add initial support for the AR934x SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26509
2011-04-07 20:52:45 +00:00
98c78c13db
ar71xx: enable access to the WAN port PHY on a few devices, adds WAN link detection
...
SVN-Revision: 26394
2011-04-02 00:47:33 +00:00
41ee4a283c
ar71xx: only allow internal access to the ar7240 switch, export the MDIO bus behind the switch instead
...
SVN-Revision: 26393
2011-04-02 00:47:29 +00:00
acbb3e50e7
ar71xx: frequent ethernet mac resets upset the MDIO bus on ar7240, so do not run them on every device open, only on tx timeouts
...
SVN-Revision: 26392
2011-04-02 00:47:25 +00:00
8eb616de82
ar71xx: add support for the TP-Link TL-WA901ND v2 board
...
Patch-by: Jonathan Benett <jbscience87@gmail.com>
SVN-Revision: 26119
2011-03-13 15:08:31 +00:00
5bddd70a37
Revert "ar71xx: add missing gpio_set_debounce function" - wrong target
...
SVN-Revision: 25854
2011-03-03 16:21:23 +00:00
57a14f4e15
ar71xx: add missing gpio_set_debounce function
...
SVN-Revision: 25848
2011-03-03 10:33:35 +00:00
256169cbd0
ar71xx: add rtl8366s initvals for the DIR-825 board
...
SVN-Revision: 25121
2011-01-26 20:35:47 +00:00
67c3e0bf7e
ar71xx: add support for the WNDR3700v2 board
...
Based on a patch by Mark Mentovai <mark@moxienet.com>
SVN-Revision: 25118
2011-01-26 20:35:42 +00:00
18ed5bca9b
fix null pointer access in mach-dir-600-a1.c machine setup ( #8671 )
...
SVN-Revision: 25043
2011-01-18 18:04:50 +00:00
b67bbfe287
ar71xx: fix wlan LED on the TL-WR741 board
...
* Patch from #8630
SVN-Revision: 24963
2011-01-11 08:20:47 +00:00
dd53effe15
ar71xx: fix wrong names of the WPS LED/button
...
Reported-by: Nuno Gonçalves
SVN-Revision: 24961
2011-01-10 18:15:47 +00:00
23a6173099
ar71xx: use gpio_*_cansleep calls in the rb4xx NAND driver
...
SVN-Revision: 24944
2011-01-09 09:29:45 +00:00
0de8689b70
ar71xx: use spinlock in ar71xx_device_{start,stop}
...
SVN-Revision: 24929
2011-01-08 11:28:32 +00:00
6acfae9379
ar71xx: enable ar7240 switch support on the UBNT NanoStation M Fixes broadcast frames on the second ethernet MAC
...
Signed-off-by: Alexander Couzens <lynxis@c-base.org>
SVN-Revision: 24723
2010-12-19 11:56:42 +00:00
cafe08a1b2
ar71xx: remove stray semicolons
...
SVN-Revision: 24651
2010-12-17 17:57:20 +00:00
01c76bf128
ar71xx: fix WLAN LEDs on the DIR-825 board
...
SVN-Revision: 24650
2010-12-17 17:10:21 +00:00
c1d3a23d19
ar71xx: add helper function to setup ath9k LED/GPIO on the AP94 based boards
...
SVN-Revision: 24649
2010-12-17 17:10:19 +00:00
8390b7dc9b
ar71xx: UBNT Secondary MAC address duplicate fix
...
There is Secondary MAC address duplicate problem with some UBNT
RouterStation and RouterStation Pro HW batches as Primary MAC addresses
are not increased by 2 per device in board data. Fix is to use 'Locally
Administrated bit' for Secondary MAC address instead of increasing
Primary MAC addresses by 1 which could overlap with other device
Primary MAC address.
Signed-off-by: Kestutis Barkauskas<keba@devint.net>
SVN-Revision: 24643
2010-12-17 17:10:01 +00:00
a2a5598c00
ar71xx: add wlan led for the TL-WR941ND
...
SVN-Revision: 24612
2010-12-15 19:55:50 +00:00
e421d2575f
ar71xx: UBNT M-Series MAC address fix
...
UBNT M-Series devices have 2 MAC addresses in board data.
Fix is to use both entries from board data instead of one entry.
Signed-off-by: Kestutis Barkauskas<keba@devint.net>
SVN-Revision: 24611
2010-12-15 19:55:47 +00:00
6c1ace2f28
ar71xx: init the LED pin for ath9k on the TL-MR3[24]20 boards
...
SVN-Revision: 24569
2010-12-14 18:01:04 +00:00
a7750dae90
ar71xx: add helper function to setup LED pin and GPIO on the AP91 based boards
...
SVN-Revision: 24568
2010-12-14 18:01:00 +00:00
9f38f9bf76
ar71xx: add missing files for the JA76PF board
...
SVN-Revision: 24444
2010-12-10 19:55:28 +00:00
b680f088ba
ar71xx: add support for the jjPlus JA79PF
...
Patch-by: Cezary Jackiewicz
SVN-Revision: 24440
2010-12-10 17:57:51 +00:00
5b0c83edd9
ar71xx: add support for the TP-LINK TL-MR3220 v1 board
...
SVN-Revision: 24439
2010-12-10 17:57:48 +00:00
8067f3f3cc
ar71xx: work around a PCI controller bug which causes reads to the PCI_COMMAND register to return bogus values - properly fixes ath9k module reload issues
...
SVN-Revision: 24236
2010-12-04 01:32:15 +00:00
9971dfe059
ar71xx: D-Link DIR-825 B1 eth1 MAC address is garbage
...
r22700 contained a copy-and-paste error that set eth0's MAC address
twice and never set eth1's.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 24036
2010-11-19 07:24:00 +00:00
920a34c0ce
ar71xx: drivers/ar71xx_wdt: fix size argument passed to copy_to_user()
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23983
2010-11-12 18:52:45 +00:00
3106aea40b
ar71xx: drivers/ag71xx: remove deprecated usage of IRQF_SAMPLE_RANDOM
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23982
2010-11-12 18:52:28 +00:00
30ef7d55fc
ar71xx: use pr_* functions in drivers
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23981
2010-11-12 18:52:12 +00:00
fddf3b8dac
ar71xx: drivers/rb4xx_nand: remove C++ comment usage
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23980
2010-11-12 18:51:55 +00:00
f4d5c885e4
ar71xx: return statements does not need parenthesis
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23979
2010-11-12 18:51:38 +00:00
e244e1c7cd
ar71xx: fix inline attribute location
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23978
2010-11-12 18:51:21 +00:00
acd8ad4de5
ar71xx: wrap long lines
...
(build errors has been fixed - juhosg)
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23977
2010-11-12 18:51:04 +00:00
eef802855a
ar71xx: fix trailing statements location
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23976
2010-11-12 18:50:47 +00:00
500fac1735
ar71xx: fix whitespaces nits
...
(build error has been fixed - juhosg)
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23975
2010-11-12 18:50:29 +00:00
20b2a4417a
Add support for Ubiquiti UniFi AP
...
SVN-Revision: 23904
2010-11-06 21:08:48 +00:00
91b6c63adc
ar71xx: Set eth1 MAC address from EEPROM for WNDR3700
...
The WNDR3700's art/caldata partition contains three MAC addresses at
offsets 0, 6, and 12, used for eth0/wlan0 (shared), eth1, and wlan1,
respectively. The existing code configures eth1's MAC address by adding
1 to eth0's instead of using the value stored in the EEPROM. This patch
causes the stored value to be used directly. (On my WNDR3700s, the three
stored addresses are all sequential anyway.)
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 23876
2010-11-04 18:46:07 +00:00
fc28e1cd7d
ar71xx: fix the wndr3700 antenna group setting for the first wireless chip (thx, Mark Mentovai)
...
SVN-Revision: 23875
2010-11-04 18:39:49 +00:00
b4e2c09b46
ar71xx: improve the wndr3700 quirks - move most of the code out of ath9k and instead allow the platform device to specify gpio overrides - fixes 5ghz signal strength issues
...
SVN-Revision: 23822
2010-11-03 14:55:53 +00:00
f056c054b9
ar71xx: the ar7240 dsa driver is no longer used, remove it.
...
SVN-Revision: 23577
2010-10-21 18:42:28 +00:00
9e2d1a194d
ar71xx: use the new ar7240 switch driver for tl-wa901nd as well
...
SVN-Revision: 23576
2010-10-21 18:42:22 +00:00
6656450c6d
ar71xx: fix more section mismatches
...
SVN-Revision: 23575
2010-10-21 18:42:16 +00:00
8858d90afe
ar71xx: improve 2.6.36 compatibility. also, instead of adding a forward port patch to the 2.6.36 patches, add a backport patch to 2.6.32
...
SVN-Revision: 23574
2010-10-21 18:42:11 +00:00
a680385396
remove remaining references to dev-ap91-eth.h, patch by Stijn Tintel
...
SVN-Revision: 23451
2010-10-14 23:08:10 +00:00
fc035b3cb6
ar71xx: remove dev-ap91-eth.c. switch its only user (RB-750) to the new switch driver
...
SVN-Revision: 23439
2010-10-14 13:41:42 +00:00
3941621dbc
ar71xx: use the new ar7240 switch driver on the DIR-600-A1 as well ( fixes #7563 )
...
SVN-Revision: 23432
2010-10-14 00:14:59 +00:00
b61a804bf7
ar71xx: increase rb4xx nand kernel partition size (patch by danimo)
...
SVN-Revision: 23293
2010-10-07 14:27:34 +00:00
697f5d0bdd
ar71xx: initial support for jjPlus JWAP003
...
Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>
(the GPIODEV code has been removed, the sysfs interface
can be used to control the GPIO lines instead - juhosg)
SVN-Revision: 23165
2010-10-01 07:09:29 +00:00
8511c6b16c
AP96: Fix LAN/WAN setup
...
LAN (eth0) is behind a switch and the fixed speed/duplex was
supposed to be for it, not WAN (eth1).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
SVN-Revision: 23147
2010-09-28 22:55:14 +00:00
32d12d5e5c
ar71xx: add support for the TL-MR3420 v1 board
...
SVN-Revision: 23136
2010-09-27 14:53:59 +00:00
b831ebdde9
ar71xx: AR724[12] requires different USB setup
...
SVN-Revision: 23135
2010-09-27 14:53:57 +00:00
cda8655910
ar71xx: use the MDIO interface of the 2nd MAC on the ar7241
...
SVN-Revision: 23132
2010-09-27 14:53:49 +00:00
b445943cdf
ar71xx: move ath9k specific PCI fixup into a separate file
...
SVN-Revision: 23131
2010-09-27 14:53:46 +00:00
4ae167959b
ar71xx: use different address in ap91_pci_fixup for the AR724[012] SoCs
...
With this change ath9k can handle the wireless chip on the TL-WR841N v7
board which is based on the AR7241 SoC.
SVN-Revision: 23130
2010-09-27 14:53:43 +00:00
a7bb7dd99e
Add support for Atheros AP96 reference board
...
This is still preliminary and not really tested much. Anyway, this
version seems to be enough to get both wired and wireless
interfaces working. Buttons and leds are also working.
mach-ap96.c is based on mach-wndr3700.c.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
SVN-Revision: 23125
2010-09-27 08:59:53 +00:00
Gabor Juhos
Felix Fietkau
Matteo Croce
Jo-Philipp Wich
Claudio Mignanti