TP-Link TL-WDR4900 v2 only has one combined WPS/Reset button, so
don't set up an RFKILL for this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 25127f58b4)
In ar71xx there is only one combined mach file for Archer C5/C7 and
TL-WDR4900 v2. This one uses the same LED struct for all devices,
defining "green" LEDs for them. However, WDR4900 uses blue front
LEDs, while only C5/C7 uses green ones. Despite, in base-files
WDR4900 is actually set up with "blue" for the mentioned LEDs.
Thus, this patch creates a separate LED struct for WDR4900, so the
LEDs can be set up correctly. Despite, the wlan5g LED is removed as
it is controlled by ath9k chip for WDR4900 (in contrast to C5/C7).
Note: While front LEDs are blue, USB LEDs (on the back) are green,
so colors are mixed intentionally for the WDR4900 v2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 93f2bcc35e)
The stock firmware and bootloader only accept uImage with names that
match certain patterns. This patch enables OpenWrt installation from
stock firmware without having to reflash the bootloader or access the
UART console.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 19800ac095)
[backported]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MAC address setup of the TL-WDR4900 v2 is different from the
C5/C7. This aligns ar71xx with the setup in ath79:
wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a9d3084b83)
As discussed in 1d18a14a90 ("ath79: really fix TP-Link Archer C7
v2 MAC address"), stock firmware MAC address assignment is
actually as follows:
wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1
This has never been fixed for ar71xx, so let's do it now.
Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned
to basemac-1 before ...
Fixes: FS#408
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a021268032)
Update WLAN LED colour identifier for both interfaces on Archer C7
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit 65762cdd22)
[backported to 18.06]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move system LED board definitions of Archer C5/C7 to reflect
actual system LED colour used
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
(cherry picked from commit a73934fc9a)
The two ASUS WL-330N and WL-330N3G had the reset keycode
assigned to the WPS button. This patch changes both devices
to use KEY_WPS_BUTTON in the hopes that this fixes unwanted
restarts/ unexpected behavior from the users point of view.
[dropped RG21S]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit ad65d9d7b2)
Commit 60f41c6c9e ("ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES
of CY-SWR1100") added stray | during backport which caused build
breakage on the buildbots:
bash: -c: line 0: syntax error near unexpected token `|'
bash: -c: line 0: `echo kmod-usb-core kmod-usb-ledtrig-usbport kmod-usb-ohci kmod-usb2 swconfig | | mkhash md5 | head -c 8'
Fixes: 60f41c6c9e ("ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit a1ff175dbf)
CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing
in default images. This commit adds it.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[changed commit title, backported to 19.07]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 261c746631)
Ethernet MAC address setup has been broken since c3e420f28c. Restore
original setting.
Fixes: c3e420f28c ("ramips: Add support for D-Link DCH-M225")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 7231c1edd9)
[backported due to base-files split]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This will have GIT ignore patches in root directory, as created
when using "git format-patch".
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 2c54135598)
Fix the error that tl-wdr3320-v2 can't upgrade firmware via web
interface by using magic_ver="0200" for this device.
Signed-off-by: 南浦月 <nanpuyue@gmail.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 0ff2385a92)
Force prereq again in SDK in order to fix GCC and Python dangling
symlinks:
staging_dir/host/bin/g++ -> /builder/ath79_generic/ccache_cxx.sh
staging_dir/host/bin/gcc -> /builder/ath79_generic/ccache_cc.sh
staging_dir/host/bin/python -> /usr/bin/python3.5
staging_dir/host/bin/python3 -> /usr/bin/python3.5
Ref: FS#2424
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 200f2666fb)
When switching from master branch to 19.07 or older, we need to ensure
that Python symlink in staging bin directory points to Python 2.
We can't rely completly just on SetupHostCommand as its executed only in
cases when the $(STAGING_DIR_HOST)/bin/python doesn't already exist, so
we need to remove it before running SetupHostCommand.
This is a cherry-pick of 3b68fb57c9
with python3 instead of python2
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 799de7c641)
Here is a way to break your build env without this patch:
1) have python point to python3, and no python2
2) start the build, SetupHostCommand will create a symlink
./staging_dir/host/bin/python -> /usr/bin/python
3) build fails on scons because it can't find any python2
4) install python2 and restart the build
5) the build fails on wireless-regdb compile because python is python3 instead of python
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 785d4f3efd)
New Docker based buildslaves install just bare minimum of packages, thus
not having bsdmainutils package installed which provides `hexdump`
utility, leading to the following build breakage on buildbots:
ubinize-image.sh: 12: /builder/scripts/ubinize-image.sh: hexdump: not found
So this patch simply replaces `hexdump` with `od` utility provided by
coreutils package, which should be likely available.
Co-authored-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c6d41c320c)
The kconfig symbol is an invisible one since its introduction. It is
not supposed to be enabled on its own.
Resolves FS#1821
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(cherry picked from commit 4bf9bec361)
Refreshed all patches.
Altered patches:
- 804-crypto-support-layerscape.patch
Compile-tested on: ar71xx
Runtime-tested on: ar71xx
Compiling target layerscape before this patch shows that it's broken.
Fixing it is out-of-scope for bumping the kernel and will
be done in a later patch.
The altered patch is a sample change which leaves the target
exactly as it was before this bump.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Even with squashfs brcm2708 requires ROOTFS_PART_SIZE because the overlay
exists as a loopback device on the space not used by squashfs in the root
partition. Also for ext4 (the other fs option) ROOTFS_PART_SIZE is required,
so use feature flag rootfs-part to enable it.
Fixes FS#2166
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
(cherry picked from commit 3bb44f4299)
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This applies to kernel 4.10 and newer.
See 8db4c5be88
The above commit added to kernel 4.10 added new dependency
for building the NETFILTER_XT_MATCH_SOCKET (xt_socket.ko)
module. The NF_SOCKET_IPVx options (both of them) need to
be enabled in order to build the NETFILTER_XT_MATCH_SOCKET
module. Without the change the module is not built.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
(cherry picked from commit 66e875a070)
(required for fixing FS#2531)
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The nf_socket.ko module was split in commit 8db4c5be88f ("netfilter:
move socket lookup infrastructure to nf_socket_ipv{4,6}.c") into a
common, n IPv4 and an IPv6 part.
The nf_tproxy.ko module was split in commit 45ca4e0cf27 ("netfilter:
Libify xt_TPROXY") into a common, an IPv4 and an IPv6 part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 89806545cc)
(required for fixing FS#2531)
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
001-Fix-compiler_state_t.ai-usage-when-INET6-is-not-defi.patch dropped due to upstream
002-Add-missing-compiler_state_t-parameter.patch dropped due to upstream
202-protocol_api.patch dropped due to implemented upstream by another way
upstream commit: 55c690f6f8
and renamed via: 697b1f7e9b
ead is the only user who use the protocol api, we have to use the new api since libpcap 1.9.0
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
This patch removes a typo (extra "0") so that the 'cpu-alert6'
step is triggered once the system reaches 85°C.
Note: Unless the WNDR4700 is placed in an hot oven, the
hardware-monitor will never reach this value.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
$(board_name) was providing content on "boardtype" (and optionally
"boardnum") NVRAM values. That function requires & expects more specific
and detailed model name extracted from the /proc/cpuinfo.
Fixes: f12a32630f ("treewide: use the generic board_name function")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Koen Vandeputte
Adrian Schmutzler
Sungbo Eo
Tomislav Požega
Rafał Miłecki
Christian Lamparter
Petr Štetiar
南浦月
Michal Cieslakiewicz
Etienne Champetier
Jo-Philipp Wich
Yousong Zhou
Daniel F. Dickinson
Oldřich Jedlička
Hauke Mehrtens
DENG Qingfang
Syrone Wong