c674c874b7
ag71xx: close a race between the phy state machine and link state
...
A fast stop/start cycle could leave the ag71xx interrupts and tx engine
disabled when using a phy driver with a fixed link and the start/stop
happens between two phy state machine polls.
Prevent this by always forcing the link down on stop regardless of phy
state and having a phy connected.
SVN-Revision: 28380
2011-10-08 11:37:14 +00:00
6ac4156136
ar71xx: fix MAC addresses on the DIR-825-B1 board
...
Patch-by: Lukas Kuna
SVN-Revision: 28295
2011-09-23 19:56:39 +00:00
733399600f
ar71xx: add support for the TP-Link TL-WR703N v1 board
...
Based on a patch by dongyuqi <729650915@qq.com>
SVN-Revision: 28277
2011-09-21 11:47:53 +00:00
d3617ac7d3
ar71xx: add AR933x specific USB setup function
...
SVN-Revision: 28276
2011-09-21 11:47:51 +00:00
91340d8af7
ar71xx: add ar71xx_device_reset_rmw helper
...
SVN-Revision: 28275
2011-09-21 11:47:50 +00:00
079e746fc4
ar71xx: remove 'default [yn]' from machine Kconfig entries
...
SVN-Revision: 28273
2011-09-21 11:47:47 +00:00
73dac07c44
ar71xx: sort AR71XX_MACH_* entries
...
SVN-Revision: 28272
2011-09-21 11:47:45 +00:00
1bdf65f580
ar71xx: fix register range check for DMA stuck checks (thx, Frédéric Moulins)
...
SVN-Revision: 28213
2011-09-11 17:44:12 +00:00
65d809ef19
ar71xx: do not count normal interrupts as spurious ( fixes #10037 )
...
SVN-Revision: 28182
2011-09-06 05:38:23 +00:00
cd2c68501c
ar71xx: fix ethernet PLL setting on ar7242
...
SVN-Revision: 28124
2011-08-29 21:23:46 +00:00
12c84f8eeb
ar71xx: add some code to detect DMA stuck conditions on ar7240
...
SVN-Revision: 27975
2011-08-13 22:30:14 +00:00
85ccc74e1b
ar71xx: on ar724x only reset the link status in the restart handler, the fast reset takes care of DMA stuck issues
...
SVN-Revision: 27973
2011-08-13 21:49:46 +00:00
d26bb6c59c
ar71xx: adjust the mtd layout of tew-632brp and dir-615c to match the image layout ( fixes #9922 )
...
SVN-Revision: 27959
2011-08-11 13:52:40 +00:00
4b75394056
ar71xx: fix ethernet FIFO state corruption on ar7240
...
When starting/stopping DMA sometimes the FIFO state gets corrupted,
leading to wildly fluctuating latencies or packet data corruption.
Fix this by issuing a fast MAC reset as soon as the link is detected
as up. Fixes #9689 , #9405
SVN-Revision: 27896
2011-08-04 17:36:31 +00:00
d2aeca6b6d
ag71xx: fix memory corruption issues on ar7240 on ethernet start/stop
...
When the DMA engine state gets corrupted due to a hardware issues, it
often won't stop rx until a full reset is issued. In that case the hardware
must keep a valid descriptor, otherwise it will write to random places in
system RAM, triggering random crashes. To fix this, keep a dummy descriptor
without a buffer that keeps the DMA engine in a sane state until the reset
is done
SVN-Revision: 27895
2011-08-04 17:36:27 +00:00
500c3a1475
ar71xx: fix MAC/MDIO reset mask handling
...
SVN-Revision: 27894
2011-08-04 17:36:23 +00:00
e18ceb1dac
ar71xx: merge WZR-HP-G301NH support into WZR-HP-G300NH
...
Now that we can use a generic name for the switch there is no need for a
separate image for the WZR-HP-G301NH.
Update the default network config and remove the extra image.
SVN-Revision: 27814
2011-07-28 11:57:51 +00:00
9e4113b493
ar71xx: autodetect rtl8366s/rtl8366rb on wzr-hp-g300nh
...
SVN-Revision: 27756
2011-07-24 14:40:35 +00:00
1afe8a0726
rtl8366: unify rtl8366s and rtl8366rb platform data
...
SVN-Revision: 27754
2011-07-24 14:40:23 +00:00
9105dad418
ar71xx: enable the usb power regulator on the wzr-hp-ag300h through gpio 2 ( #9684 )
...
SVN-Revision: 27739
2011-07-24 08:02:20 +00:00
c7173a211d
ar71xx: reinitialize global switch settings after reset on ar7240
...
SVN-Revision: 27705
2011-07-20 14:39:47 +00:00
ca473833c4
ar71xx: configure address aging on ar7240
...
SVN-Revision: 27704
2011-07-20 14:39:42 +00:00
fefc79f3cb
ar71xx: reset the phy in the ethernet init on ar724x
...
SVN-Revision: 27703
2011-07-20 12:04:34 +00:00
005fe5d1fd
ar71xx: make sure that rx and interrupts are disabled before issuing the hardware reset
...
SVN-Revision: 27702
2011-07-20 12:04:29 +00:00
e7ab000008
ar71xx: increase the delay after the ethernet MAC reset
...
SVN-Revision: 27701
2011-07-20 12:04:25 +00:00
255dcaa3a6
ar71xx: fix an unused variable warning
...
SVN-Revision: 27700
2011-07-20 12:04:20 +00:00
f3d693c0ee
ar71xx: do not reset the hardware on transmit timeout - this would mess up the up the PHY state
...
SVN-Revision: 27568
2011-07-09 06:30:13 +00:00
2806c75c07
ag71xx: keep the rx engine stopped while the link is not up, should hopefully fix stability issues from #9405
...
SVN-Revision: 27567
2011-07-09 06:29:46 +00:00
f9e4619b97
ar71xx: remove CONFIG_MTD_CONCAT ifdefs from the WZR-HP-AG300H code
...
The config option has been removed in 2.6.39.
SVN-Revision: 27320
2011-06-30 12:15:33 +00:00
d98476c6bd
ar71xx: merge 2.6.39 patches
...
Also remove the old UART driver for ar933x.
SVN-Revision: 27314
2011-06-29 08:57:37 +00:00
6627574e57
ar71xx: add 2.6.39 support
...
SVN-Revision: 27310
2011-06-29 08:57:32 +00:00
1e138098cd
ar71xx: remove ar71xx_gpio_irq_set_type
...
SVN-Revision: 27309
2011-06-29 08:57:30 +00:00
055e317ed8
ar71xx: add separate handlers for IP3 interrupts
...
SVN-Revision: 27308
2011-06-29 08:57:29 +00:00
59bff8bf18
ar71xx: use separate handlers for IP2 interrupts
...
SVN-Revision: 27307
2011-06-29 08:57:28 +00:00
9d6af600e1
ar71xx: remove useless irq_desc.status initializations
...
SVN-Revision: 27306
2011-06-29 08:57:27 +00:00
ed7f41792a
ar71xx: bring up secondary radio on wzr-hp-ag300h ( fixes #9608 )
...
SVN-Revision: 27282
2011-06-25 13:48:47 +00:00
e6af77a1c8
ar71xx: cleanup AR933X UART driver
...
SVN-Revision: 27222
2011-06-19 13:17:51 +00:00
066e04d497
ar71xx: fix uart clock frequency for AR933X
...
SVN-Revision: 27221
2011-06-19 13:17:50 +00:00
b7e016ba42
ar71xx: use ar933x_uart.h in the AR933X serial driver
...
SVN-Revision: 27166
2011-06-13 08:12:40 +00:00
b58ede16a5
ar71xx: update early_printk code
...
SVN-Revision: 27165
2011-06-13 08:12:38 +00:00
13363d9129
ar71xx: setup wdt_clock for AR913X to avoid a kernel bug
...
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 27102
2011-06-04 12:30:10 +00:00
ae2cbfa1e8
ar71xx: select the internal antenna by default on the ZCN-1523H boards
...
SVN-Revision: 27101
2011-06-04 12:30:09 +00:00
31dd60689e
Revert "ar71xx: only enable the rx engine after the link is up..."
...
It messes up the DMA state when the link goes down
SVN-Revision: 27088
2011-06-01 18:15:43 +00:00
750af1522b
ar71xx: init external_reset for AR933X
...
SVN-Revision: 27083
2011-06-01 13:12:30 +00:00
af4cae4498
ar71xx: add external_reset field to ath9k_platform_data
...
SVN-Revision: 27082
2011-06-01 13:12:28 +00:00
f0c7b93e5d
ar71xx: init get_mac_revision on AR9330 rev 1
...
SVN-Revision: 27081
2011-06-01 13:12:27 +00:00
1a54e33c17
ar71xx: add get_mac_revision to ath9k_platform_data
...
SVN-Revision: 27080
2011-06-01 13:12:26 +00:00
34ff32a6eb
ar71xx: export SoC revision
...
SVN-Revision: 27079
2011-06-01 13:12:24 +00:00
4f06b8263a
ar71xx: add kernel support for the buffalo wzr-hp-ag300h
...
SVN-Revision: 27075
2011-06-01 02:23:26 +00:00
f332dbd7be
ar71xx: add support for the AP121/AP121-MINI reference boards
...
SVN-Revision: 27067
2011-05-31 22:53:43 +00:00
8beff081eb
ar71xx: register UART for the AR933X SoCs
...
SVN-Revision: 27066
2011-05-31 22:53:42 +00:00
b460bc6f12
ar71xx: add serial driver for the AR933X UART
...
SVN-Revision: 27065
2011-05-31 22:53:40 +00:00
c34e0cbc4c
ar71xx: add WMAC initialization code for the AR933X SoCs
...
SVN-Revision: 27064
2011-05-31 22:53:39 +00:00
e8a0aaf9a2
ar71xx: add ethernet initialization for the AR933X SoCs
...
SVN-Revision: 27063
2011-05-31 22:53:37 +00:00
e0a0f3796a
ar71xx: enable USB support for the AR933x SoCs
...
SVN-Revision: 27062
2011-05-31 22:53:36 +00:00
677c80ee17
ar71xx: add AR933x specific glue for ar71xx_device{start,stop}
...
SVN-Revision: 27061
2011-05-31 22:53:35 +00:00
88c45e3130
ar71xx: the watchdog uses the reference clock on the AR933x SoCs
...
SVN-Revision: 27060
2011-05-31 22:53:34 +00:00
7acbacab8c
ar71xx: add AR933x specific glue code for IRQ initialization
...
SVN-Revision: 27059
2011-05-31 22:53:32 +00:00
e6fde61bec
ar71xx: don't register 8250 UART on the AR933x SoCs
...
SVN-Revision: 27058
2011-05-31 22:53:31 +00:00
8f7541a044
ar71xx: enable GPIO support for the AR933x SoCs
...
SVN-Revision: 27057
2011-05-31 22:53:30 +00:00
e11b9c8371
ar71xx: add AR933x specific frequency initialization code
...
SVN-Revision: 27056
2011-05-31 22:53:29 +00:00
0bf4478d37
ar71xx: add AR933x specific early_printk support
...
SVN-Revision: 27055
2011-05-31 22:53:27 +00:00
6b3ca9ef0b
ar71xx: add preliminary support for the Atheros AR933x SoCs
...
SVN-Revision: 27054
2011-05-31 22:53:26 +00:00
0677e16248
ar71xx: Fix header offset for newer WRT160NL models
...
Newer WRT160NLs have a flash chip with 4K erase blocks instead of 64K,
resulting in miscalculated partition sizes.
Since the actual sizes did not change, hardcode them to their current
sizes, and make sure they are at least one erase block big (in case Cisco
decides to start to use chips with 128K erase blocks).
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 27049
2011-05-31 22:53:20 +00:00
be97e2a043
ar71xx: add SOC_AR{71XX,724X,913X,934X} config symbols
...
SVN-Revision: 27048
2011-05-31 22:53:19 +00:00
5d5f72415e
ar71xx: initialize is_clk_25mhz field for AR9340 WMAC
...
SVN-Revision: 27045
2011-05-31 22:53:15 +00:00
f7b3c3dfd1
ar71xx: sync ath9k_platform_data.h with compat-wireless
...
SVN-Revision: 27044
2011-05-31 22:53:14 +00:00
60d5abbc27
ar71xx: ag71xx: make ring sizes configurable via ethtool
...
SVN-Revision: 27041
2011-05-31 22:53:10 +00:00
7a2651f633
ar71xx: ag71xx: prepare to make ring sizes configurable
...
SVN-Revision: 27040
2011-05-31 22:53:09 +00:00
669aba3871
ar71xx: ag71xx: nuke unused AG71XX_TX_FIFO_LEN define
...
Reported-by: Dave Täht <dave.taht@gmail.com>
SVN-Revision: 27039
2011-05-31 22:53:07 +00:00
2b5402d128
ar71xx: only enable the rx engine after the link is up, fixes a race condition that got rx stuck when the interface is brought up during lots of inbound traffic (thx, matteo)
...
SVN-Revision: 27035
2011-05-30 23:08:01 +00:00
0ebc93831f
ar71xx: disable flow control for ar724x, it can get stuck in a loop of continously sending MAC pause frames
...
SVN-Revision: 27034
2011-05-30 23:07:57 +00:00
17e257925f
ar71xx: don't probe the LAN PHY
...
SVN-Revision: 26924
2011-05-17 11:15:24 +00:00
4deecea26b
ar71xx: detect link on LAN ports
...
SVN-Revision: 26922
2011-05-17 11:12:56 +00:00
2ea528d1d0
ar71xx: add link detection on Ubiquiti devices WAN port
...
SVN-Revision: 26891
2011-05-14 23:31:50 +00:00
c0c2e18452
use correct macros and frame size in ag71xx
...
SVN-Revision: 26890
2011-05-14 23:10:06 +00:00
99d1d4f795
ar71xx: cosmetic fixes
...
SVN-Revision: 26889
2011-05-14 23:08:00 +00:00
9b5036a29d
ar71xx: populate LED3 on the JA76PF board
...
Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>
SVN-Revision: 26862
2011-05-08 21:38:51 +00:00
869f3cb718
ar71xx: remove superfluous fifo_cfg overrides
...
SVN-Revision: 26859
2011-05-08 21:38:46 +00:00
5d77f370d6
ar71xx: ag71xx: make switch register access atomic
...
Reading of the PHY registers occasionally returns with bogus values
under heavy load. This misleads the PHY driver and thus causes false
link/speed change notifications which leads to performance loss.
This is easily noticable during an iperf session:
...
[ 3] 52.0-53.0 sec 11.3 MBytes 94.4 Mbits/sec
[ 3] 53.0-54.0 sec 11.4 MBytes 95.4 Mbits/sec
eth1: link down
br-lan: port 2(eth1) entering forwarding state
eth1: link up (100Mbps/Full duplex)
br-lan: port 2(eth1) entering forwarding state
br-lan: port 2(eth1) entering forwarding state
[ 3] 54.0-55.0 sec 6.75 MBytes 56.6 Mbits/sec
[ 3] 55.0-56.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 56.0-57.0 sec 10.5 MBytes 88.1 Mbits/sec
...
[ 3] 169.0-170.0 sec 11.4 MBytes 95.4 Mbits/sec
[ 3] 170.0-171.0 sec 11.4 MBytes 95.4 Mbits/sec
eth1: link up (10Mbps/Half duplex)
[ 3] 171.0-172.0 sec 7.63 MBytes 64.0 Mbits/sec
[ 3] 172.0-173.0 sec 9.38 MBytes 78.6 Mbits/sec
eth1: link up (100Mbps/Full duplex)
[ 3] 173.0-174.0 sec 11.3 MBytes 94.4 Mbits/sec
[ 3] 174.0-175.0 sec 11.4 MBytes 95.4 Mbits/sec
SVN-Revision: 26856
2011-05-08 16:32:53 +00:00
3711658281
ar71xx: ag71xx: fix section mismatch warnings
...
The function __devinit ag71xx_probe() references
a function __devexit ag71xx_phy_disconnect().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
ag71xx_phy_disconnect() so it may be used outside an exit section.
The function ag71xx_phy_disconnect() references a function in an exit
section.
Often the function ag71xx_ar7240_cleanup() has valid usage outside the
exit section
and the fix is to remove the __devexit annotation of
ag71xx_ar7240_cleanup.
SVN-Revision: 26855
2011-05-08 13:30:36 +00:00
ef53029870
ar71xx: ag71xx: fix build error if debugfs is enabled
...
SVN-Revision: 26854
2011-05-08 13:30:26 +00:00
8b67d748cb
ar71xx: ag71xx: add debugfs entry for [rt]x_ring
...
SVN-Revision: 26845
2011-05-07 12:40:34 +00:00
2166432ba0
ar71xx: ag71xx: add timestamps to ag71xx_buf
...
SVN-Revision: 26844
2011-05-07 12:40:28 +00:00
896e1d1ab4
ar71xx: ag71xx: use dynamically allocated buffer for napi_stats
...
SVN-Revision: 26843
2011-05-07 12:40:26 +00:00
a6708d20d1
ar71xx: ag71xx: use debugfs_remove_recursive
...
SVN-Revision: 26842
2011-05-07 12:40:25 +00:00
c39e5b9360
ar71xx: override wmac device name for the AR934x SoCs
...
SVN-Revision: 26840
2011-05-07 09:23:32 +00:00
cbc75a9c70
ar71xx: use the ar8316 switch driver on the PB92 board and add a matching default network config
...
SVN-Revision: 26779
2011-04-28 21:27:42 +00:00
36aecb08b8
ar71xx: fix MDIO access on ar7242 (based on a patch by Jess Zhu)
...
SVN-Revision: 26777
2011-04-28 19:30:49 +00:00
fa9f45f345
ar71xx: fix build error w/o CONFIG_PCI
...
SVN-Revision: 26606
2011-04-12 13:14:56 +00:00
e193547733
ar71xx: use the gpio_keys_polled driver instead of gpio_buttons
...
SVN-Revision: 26603
2011-04-12 09:29:21 +00:00
54ede24829
ar71xx: Add support for WZR-HP-G301NH
...
Add support for the Buffalo WZR-HP-G301NH. The only difference between it
and the WZR-HP-G00NH is that it has a RTL8366RB instead of a RTL8366S.
Since we don't do runtime detection of the switch, we need a separate
machine definition for it.
While we are at it, also rename the profile to reflect that it now is for
more than one device.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26601
2011-04-12 09:29:10 +00:00
ef4c1d49a6
ar71xx: merge dev-ar9{13,34}x-wmac into dev-ar9xxx-wmac
...
SVN-Revision: 26595
2011-04-11 17:37:08 +00:00
4711dea8ff
ar71xx: fix AR934X_WMAC_SIZE
...
SVN-Revision: 26594
2011-04-11 17:37:03 +00:00
8586e61b00
ar71xx: fix section mismatch
...
SVN-Revision: 26562
2011-04-09 18:47:55 +00:00
a8bf5e3cdb
ar71xx: rename ar934x_ref_freq to ar71xx_ref_freq
...
Also initialize that for each SoC and print its value along with the
other frequencies.
SVN-Revision: 26561
2011-04-09 18:47:52 +00:00
5573d6eb28
ar71xx: show the SoC type earlier
...
SVN-Revision: 26560
2011-04-09 18:47:50 +00:00
ab4c3b3a1c
ar71xx: cleanup SoC detection code
...
SVN-Revision: 26559
2011-04-09 18:47:49 +00:00
3310c70702
ar71xx: Fix mac address offset for AR934x
...
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
SVN-Revision: 26557
2011-04-09 18:47:42 +00:00
8f889f9250
ar71xx: add DB120 board specific PCI initialization
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26523
2011-04-07 20:53:41 +00:00
a0c3d49064
ar71xx: register WMAC device on the DB120 board
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26522
2011-04-07 20:53:37 +00:00
428888faec
ar71xx: add support for the built-in WMAC of the AR934x
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26521
2011-04-07 20:53:34 +00:00
14b42c44ec
ar71xx: add initial support for the Atheros DB120 board
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26518
2011-04-07 20:53:19 +00:00
2b064bb398
ar71xx: add support for the watchdog of the AR934x SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26516
2011-04-07 20:53:10 +00:00
e4555809c7
ar71xx: enable PCI for the AR934[24] SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26515
2011-04-07 20:53:05 +00:00
4f395745af
ar71xx: enable USB support for the AR934x SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26514
2011-04-07 20:53:03 +00:00
25693b4769
ar71xx: enable GPIO support for the AR934x SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26513
2011-04-07 20:53:00 +00:00
334a5ec36e
ar71xx: add AR934x specific glue for ar7100_device{start,stop}
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26512
2011-04-07 20:52:57 +00:00
ccd3ebd309
ar71xx: add AR934x specific UART clock initialization
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26511
2011-04-07 20:52:53 +00:00
91470edada
ar71xx: add AR934x specific glue for IRQ initialization
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26510
2011-04-07 20:52:49 +00:00
3b209880bc
ar71xx: add initial support for the AR934x SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26509
2011-04-07 20:52:45 +00:00
98c78c13db
ar71xx: enable access to the WAN port PHY on a few devices, adds WAN link detection
...
SVN-Revision: 26394
2011-04-02 00:47:33 +00:00
41ee4a283c
ar71xx: only allow internal access to the ar7240 switch, export the MDIO bus behind the switch instead
...
SVN-Revision: 26393
2011-04-02 00:47:29 +00:00
acbb3e50e7
ar71xx: frequent ethernet mac resets upset the MDIO bus on ar7240, so do not run them on every device open, only on tx timeouts
...
SVN-Revision: 26392
2011-04-02 00:47:25 +00:00
8eb616de82
ar71xx: add support for the TP-Link TL-WA901ND v2 board
...
Patch-by: Jonathan Benett <jbscience87@gmail.com>
SVN-Revision: 26119
2011-03-13 15:08:31 +00:00
5bddd70a37
Revert "ar71xx: add missing gpio_set_debounce function" - wrong target
...
SVN-Revision: 25854
2011-03-03 16:21:23 +00:00
57a14f4e15
ar71xx: add missing gpio_set_debounce function
...
SVN-Revision: 25848
2011-03-03 10:33:35 +00:00
256169cbd0
ar71xx: add rtl8366s initvals for the DIR-825 board
...
SVN-Revision: 25121
2011-01-26 20:35:47 +00:00
67c3e0bf7e
ar71xx: add support for the WNDR3700v2 board
...
Based on a patch by Mark Mentovai <mark@moxienet.com>
SVN-Revision: 25118
2011-01-26 20:35:42 +00:00
18ed5bca9b
fix null pointer access in mach-dir-600-a1.c machine setup ( #8671 )
...
SVN-Revision: 25043
2011-01-18 18:04:50 +00:00
b67bbfe287
ar71xx: fix wlan LED on the TL-WR741 board
...
* Patch from #8630
SVN-Revision: 24963
2011-01-11 08:20:47 +00:00
dd53effe15
ar71xx: fix wrong names of the WPS LED/button
...
Reported-by: Nuno Gonçalves
SVN-Revision: 24961
2011-01-10 18:15:47 +00:00
23a6173099
ar71xx: use gpio_*_cansleep calls in the rb4xx NAND driver
...
SVN-Revision: 24944
2011-01-09 09:29:45 +00:00
0de8689b70
ar71xx: use spinlock in ar71xx_device_{start,stop}
...
SVN-Revision: 24929
2011-01-08 11:28:32 +00:00
6acfae9379
ar71xx: enable ar7240 switch support on the UBNT NanoStation M Fixes broadcast frames on the second ethernet MAC
...
Signed-off-by: Alexander Couzens <lynxis@c-base.org>
SVN-Revision: 24723
2010-12-19 11:56:42 +00:00
cafe08a1b2
ar71xx: remove stray semicolons
...
SVN-Revision: 24651
2010-12-17 17:57:20 +00:00
01c76bf128
ar71xx: fix WLAN LEDs on the DIR-825 board
...
SVN-Revision: 24650
2010-12-17 17:10:21 +00:00
c1d3a23d19
ar71xx: add helper function to setup ath9k LED/GPIO on the AP94 based boards
...
SVN-Revision: 24649
2010-12-17 17:10:19 +00:00
8390b7dc9b
ar71xx: UBNT Secondary MAC address duplicate fix
...
There is Secondary MAC address duplicate problem with some UBNT
RouterStation and RouterStation Pro HW batches as Primary MAC addresses
are not increased by 2 per device in board data. Fix is to use 'Locally
Administrated bit' for Secondary MAC address instead of increasing
Primary MAC addresses by 1 which could overlap with other device
Primary MAC address.
Signed-off-by: Kestutis Barkauskas<keba@devint.net>
SVN-Revision: 24643
2010-12-17 17:10:01 +00:00
a2a5598c00
ar71xx: add wlan led for the TL-WR941ND
...
SVN-Revision: 24612
2010-12-15 19:55:50 +00:00
e421d2575f
ar71xx: UBNT M-Series MAC address fix
...
UBNT M-Series devices have 2 MAC addresses in board data.
Fix is to use both entries from board data instead of one entry.
Signed-off-by: Kestutis Barkauskas<keba@devint.net>
SVN-Revision: 24611
2010-12-15 19:55:47 +00:00
6c1ace2f28
ar71xx: init the LED pin for ath9k on the TL-MR3[24]20 boards
...
SVN-Revision: 24569
2010-12-14 18:01:04 +00:00
a7750dae90
ar71xx: add helper function to setup LED pin and GPIO on the AP91 based boards
...
SVN-Revision: 24568
2010-12-14 18:01:00 +00:00
9f38f9bf76
ar71xx: add missing files for the JA76PF board
...
SVN-Revision: 24444
2010-12-10 19:55:28 +00:00
b680f088ba
ar71xx: add support for the jjPlus JA79PF
...
Patch-by: Cezary Jackiewicz
SVN-Revision: 24440
2010-12-10 17:57:51 +00:00
5b0c83edd9
ar71xx: add support for the TP-LINK TL-MR3220 v1 board
...
SVN-Revision: 24439
2010-12-10 17:57:48 +00:00
8067f3f3cc
ar71xx: work around a PCI controller bug which causes reads to the PCI_COMMAND register to return bogus values - properly fixes ath9k module reload issues
...
SVN-Revision: 24236
2010-12-04 01:32:15 +00:00
9971dfe059
ar71xx: D-Link DIR-825 B1 eth1 MAC address is garbage
...
r22700 contained a copy-and-paste error that set eth0's MAC address
twice and never set eth1's.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 24036
2010-11-19 07:24:00 +00:00
920a34c0ce
ar71xx: drivers/ar71xx_wdt: fix size argument passed to copy_to_user()
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23983
2010-11-12 18:52:45 +00:00
3106aea40b
ar71xx: drivers/ag71xx: remove deprecated usage of IRQF_SAMPLE_RANDOM
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23982
2010-11-12 18:52:28 +00:00
30ef7d55fc
ar71xx: use pr_* functions in drivers
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23981
2010-11-12 18:52:12 +00:00
fddf3b8dac
ar71xx: drivers/rb4xx_nand: remove C++ comment usage
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23980
2010-11-12 18:51:55 +00:00
f4d5c885e4
ar71xx: return statements does not need parenthesis
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23979
2010-11-12 18:51:38 +00:00
e244e1c7cd
ar71xx: fix inline attribute location
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23978
2010-11-12 18:51:21 +00:00
acd8ad4de5
ar71xx: wrap long lines
...
(build errors has been fixed - juhosg)
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23977
2010-11-12 18:51:04 +00:00
eef802855a
ar71xx: fix trailing statements location
...
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23976
2010-11-12 18:50:47 +00:00
500fac1735
ar71xx: fix whitespaces nits
...
(build error has been fixed - juhosg)
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
SVN-Revision: 23975
2010-11-12 18:50:29 +00:00
20b2a4417a
Add support for Ubiquiti UniFi AP
...
SVN-Revision: 23904
2010-11-06 21:08:48 +00:00
91b6c63adc
ar71xx: Set eth1 MAC address from EEPROM for WNDR3700
...
The WNDR3700's art/caldata partition contains three MAC addresses at
offsets 0, 6, and 12, used for eth0/wlan0 (shared), eth1, and wlan1,
respectively. The existing code configures eth1's MAC address by adding
1 to eth0's instead of using the value stored in the EEPROM. This patch
causes the stored value to be used directly. (On my WNDR3700s, the three
stored addresses are all sequential anyway.)
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 23876
2010-11-04 18:46:07 +00:00
fc28e1cd7d
ar71xx: fix the wndr3700 antenna group setting for the first wireless chip (thx, Mark Mentovai)
...
SVN-Revision: 23875
2010-11-04 18:39:49 +00:00
b4e2c09b46
ar71xx: improve the wndr3700 quirks - move most of the code out of ath9k and instead allow the platform device to specify gpio overrides - fixes 5ghz signal strength issues
...
SVN-Revision: 23822
2010-11-03 14:55:53 +00:00
f056c054b9
ar71xx: the ar7240 dsa driver is no longer used, remove it.
...
SVN-Revision: 23577
2010-10-21 18:42:28 +00:00
9e2d1a194d
ar71xx: use the new ar7240 switch driver for tl-wa901nd as well
...
SVN-Revision: 23576
2010-10-21 18:42:22 +00:00
6656450c6d
ar71xx: fix more section mismatches
...
SVN-Revision: 23575
2010-10-21 18:42:16 +00:00
8858d90afe
ar71xx: improve 2.6.36 compatibility. also, instead of adding a forward port patch to the 2.6.36 patches, add a backport patch to 2.6.32
...
SVN-Revision: 23574
2010-10-21 18:42:11 +00:00
a680385396
remove remaining references to dev-ap91-eth.h, patch by Stijn Tintel
...
SVN-Revision: 23451
2010-10-14 23:08:10 +00:00
fc035b3cb6
ar71xx: remove dev-ap91-eth.c. switch its only user (RB-750) to the new switch driver
...
SVN-Revision: 23439
2010-10-14 13:41:42 +00:00
3941621dbc
ar71xx: use the new ar7240 switch driver on the DIR-600-A1 as well ( fixes #7563 )
...
SVN-Revision: 23432
2010-10-14 00:14:59 +00:00
b61a804bf7
ar71xx: increase rb4xx nand kernel partition size (patch by danimo)
...
SVN-Revision: 23293
2010-10-07 14:27:34 +00:00
697f5d0bdd
ar71xx: initial support for jjPlus JWAP003
...
Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>
(the GPIODEV code has been removed, the sysfs interface
can be used to control the GPIO lines instead - juhosg)
SVN-Revision: 23165
2010-10-01 07:09:29 +00:00
8511c6b16c
AP96: Fix LAN/WAN setup
...
LAN (eth0) is behind a switch and the fixed speed/duplex was
supposed to be for it, not WAN (eth1).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
SVN-Revision: 23147
2010-09-28 22:55:14 +00:00
32d12d5e5c
ar71xx: add support for the TL-MR3420 v1 board
...
SVN-Revision: 23136
2010-09-27 14:53:59 +00:00
b831ebdde9
ar71xx: AR724[12] requires different USB setup
...
SVN-Revision: 23135
2010-09-27 14:53:57 +00:00
cda8655910
ar71xx: use the MDIO interface of the 2nd MAC on the ar7241
...
SVN-Revision: 23132
2010-09-27 14:53:49 +00:00
b445943cdf
ar71xx: move ath9k specific PCI fixup into a separate file
...
SVN-Revision: 23131
2010-09-27 14:53:46 +00:00
4ae167959b
ar71xx: use different address in ap91_pci_fixup for the AR724[012] SoCs
...
With this change ath9k can handle the wireless chip on the TL-WR841N v7
board which is based on the AR7241 SoC.
SVN-Revision: 23130
2010-09-27 14:53:43 +00:00
a7bb7dd99e
Add support for Atheros AP96 reference board
...
This is still preliminary and not really tested much. Anyway, this
version seems to be enough to get both wired and wireless
interfaces working. Buttons and leds are also working.
mach-ap96.c is based on mach-wndr3700.c.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
SVN-Revision: 23125
2010-09-27 08:59:53 +00:00
0c6653c6e2
ar71xx: select AR71XX_DEV_DSA when AR71XX_DEV_AP91_ETH is selected, do not select AR71XX_DEV_AP91_ETH for TL-WA901ND and TL-WR741ND
...
SVN-Revision: 22935
2010-09-05 16:17:06 +00:00
b4336a8e2d
ar71xx: add support for the Zcomax ZCN-1523H-2-8/5-16 boards
...
SVN-Revision: 22882
2010-09-03 18:14:37 +00:00
47f8fd1dde
ar71xx: rewrite SPI drivers for the RB4xx boards
...
* add a new SPI controller driver
* add SPI driver for the CPLD chip
* convert the NAND driver
* enable the mikroSD slot
* enable more LEDs
SVN-Revision: 22863
2010-08-31 20:13:47 +00:00
7bc5a672c1
ar71xx: change mac address initialization
...
SVN-Revision: 22700
2010-08-18 16:00:28 +00:00
523fcf0497
ar71xx: add a new driver for the ar7240 switch using swconfig. hooks directly into the ethernet driver, as MAC resets also require switch reinitializations and the switch is part of the cpu core anyway switch only tl-wr741nd (and other devices using this board file, such as tl-wr841nd) over to using this by default, as other devices are still untested fixes #7563
...
SVN-Revision: 22675
2010-08-16 19:21:57 +00:00
65899cfa49
ar71xx: remove the fifo cfg overrides for the ap91 ethernet code - these values have been wrong on every single device i've tested, falling back to the atheros values seems to be the right thing to do
...
SVN-Revision: 22401
2010-07-27 21:04:43 +00:00
900aaa919b
ar71xx: add support for the tp-link tl-wa901nd devices (patch by Pieter "Fate" Hollants, from #7528 , without the ethernet fifo cfg values)
...
SVN-Revision: 22353
2010-07-22 12:37:44 +00:00
bced5d7d74
ar71xx: set default values for the fifo cfg registers on AR724x
...
SVN-Revision: 22303
2010-07-20 01:54:11 +00:00
4bb11f9a39
generic: move ath5k_platform.h from ar71xx to generic files
...
SVN-Revision: 22189
2010-07-15 07:36:58 +00:00
95e09cccd8
ar71xx: in-flash macs and eeprom for mach-eap7660d
...
This adds in-flash mac-addresses and calibration data for the Senao
EAP7660D board.
Signed-off-by: Daniel Golle <daniel.golle@gmail.com>
SVN-Revision: 22187
2010-07-15 07:36:52 +00:00
a27ea45e76
ar71xx: only reinit the ethernet MAC at .open() on ar724x for now, until we've figured out what part of it causes the issue described in #7563
...
SVN-Revision: 22075
2010-07-06 12:40:07 +00:00
15b209d09f
ag71xx: reset the hardware during open(), this improves recovery from tx timeouts on ar724x considerably
...
SVN-Revision: 22055
2010-07-04 02:15:08 +00:00
89da22d1ea
ag71xx: fix a memory corruption bug that happens if you flood the interface with packets while it's being brought down fixes boot time crashes under load reported by matteo
...
SVN-Revision: 22054
2010-07-04 01:31:33 +00:00
5a28fb88a4
ar71xx: fix leds-rb750 build failure on 2.6.34
...
SVN-Revision: 22016
2010-07-01 14:49:06 +00:00
7bff9c0101
ar71xx: add support for the Senao EAP7660D board
...
This patch adds support for the Senao EAP7660D board to trunk.
Signed-off-by: Daniel Golle <daniel.golle@gmail.com>
SVN-Revision: 21837
2010-06-18 16:22:05 +00:00
08c2e29018
ar71xx: avoid duplicated 'board' parameter in kernel command line
...
SVN-Revision: 21805
2010-06-14 20:02:44 +00:00
9789f0215a
ar71xx: nuke AR71XX_MACH_UBNT_AR71XX machtype
...
SVN-Revision: 21764
2010-06-12 13:20:39 +00:00
adb0a95df1
ar71xx: fix phy_mask for the RB450
...
SVN-Revision: 21743
2010-06-09 19:48:35 +00:00
6ce447427c
ar71xx: fix build error in the rb{4xx,750}_nand drivers on 2.6.34/35
...
SVN-Revision: 21736
2010-06-09 15:31:34 +00:00
d55ebf3a8a
ar71xx: fix phy_mask on the RB433 for the IP17xx driver
...
SVN-Revision: 21728
2010-06-08 20:19:18 +00:00
90e2b1ad6b
ar71xx: fix 2.6.34 build errors
...
SVN-Revision: 21698
2010-06-07 09:18:13 +00:00
115f845e53
ar71xx: fix nbg460n mtd partitions
...
This fixes the NBG460N/550N/550NH mtd partitions.
Signed-off-by: Michael Kurz <michi.kurz@googlemail.com>
SVN-Revision: 21443
2010-05-14 08:37:58 +00:00
fca9b7ebad
ar71xx: remove config partition from the mtd map on the MZK-W300NH board
...
This space can be used to extend the rootfs_data partition.
SVN-Revision: 21173
2010-04-26 18:28:04 +00:00
77b2354fcd
ar71xx: fix firmware partition size on the MZK-W04NU board
...
SVN-Revision: 21172
2010-04-26 18:28:01 +00:00
7966004d99
ag71xx: remove rx alignment code for small packets, it seems to break ipv6 for some reason ( fixes #7236 )
...
SVN-Revision: 21166
2010-04-26 16:39:13 +00:00
9848d38aed
ar71xx: fix a wifi card stability issue
...
when we receive a pci/ahb interrupt, we need to flush pending data for dma
from the device, otherwise the tx path may get stuck if the completion flag
of the dma descriptor is not updated at the time the tx interrupt arrives.
SVN-Revision: 21143
2010-04-24 17:24:11 +00:00
10ed3b23a6
ar71xx: reduce button threshold value on the NBG460 board
...
SVN-Revision: 21076
2010-04-21 19:07:23 +00:00
9933d34770
ar71xx: use KEY_RESTART and KEY_WPS_BUTTON code for the appropriate buttons
...
SVN-Revision: 21075
2010-04-21 19:07:19 +00:00
693ea524c1
ar71xx: adding support for zyxel nbg460n/550n/550nh boards
...
This patch adds support for the zyxel nbg460n/550n/550nh routers.
Currently this only works if a second stage bootloader is also flashed,
as the used switch needs extra initialization.
Signed-off-by: Michael Kurz <michi.kurz@googlemail.com>
SVN-Revision: 20990
2010-04-18 16:24:12 +00:00
1c0e751391
ar71xx: fix up alignment handling
...
- on ar724x, rx buffers can be aligned with an offset of 2, which keeps the ip header aligned
- alignment offset is only added if the ar8216 workaround is not active and the phy driver does not advertise its own packet alignment
- ar71xx and ar91xx can not handle rx alignment offsets, however taking a hit on unaligned exceptions seems to have less overhead than re-aligning the data for large packets
- use memmove to re-align small packets, if necessary
tested on ar9132, ar7240 and ar7242 based devices without ar8216 headers
SVN-Revision: 20892
2010-04-15 23:31:17 +00:00
dd7304ec6d
ar71xx: update phy masks for the Planex boards
...
This avoids probing of the AR8216 chip on the eth0 interface.
Cc: backfire@openwrt.org
SVN-Revision: 20754
2010-04-09 08:40:14 +00:00
d6c0363884
ar71xx: make the AR8216 driver usable on the TEW-632BRP/DIR-615-Cx boards
...
Cc: backfire@openwrt.org
SVN-Revision: 20752
2010-04-09 08:40:09 +00:00
4c29a2c263
ar71xx: ag71xx: avoid unalinged accesses when using the phy specific receive functions
...
Cc: backfire@openwrt.org
SVN-Revision: 20751
2010-04-09 08:40:06 +00:00
Jonas Gorski
Gabor Juhos
Felix Fietkau
Matteo Croce
Jo-Philipp Wich
Claudio Mignanti