This patch adds support for the amcc,usb-otg-405ex device
which is found in all APM82181 SoCs.
Note: The system can't use the generic "snps,dwc2" compatible
because of the special ahbcfg configuration. The default
GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang
when the USB and SATA is used concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
As specified by e0229a16b0 if the VR9
based router provides FXS ports and they should enabled then the
following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M
By adding mem= parameter a pci device stop working correctly. The
pci-lantiq.c module use get_num_physpages() to compute dynamically the
memory amount of the board.
The mem= make the module to compute in the wrong way the BAR11MASK, so
in this situation the mask is misaligned with the dma area that the
hardware expects.
This patch is a port of what legacy ifxmips_pci.c does.
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
This adds support for "channels" command which displays more details
about channels. It includes e.g. info about available widths.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The latest stock firmwares for US and EU regions have started checking the
region code.
Tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some builders have troubles cloning the boot-wrapper-aarch64.git repository so
provide a mirror checksum to allow downloading from sources.lede-project.org
instead.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
A firmware compiled with BUSYBOX_CONFIG_ARP should also use by default the
arp binary from busybox. Otherwise the extra functionality the user
requested can only be used when running arp with the path to the binary.
Signed-off-by: Marek Lindner <marek.lindner@open-mesh.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Assign an unused MAC addresses to the 2.4GHz wifi interface as it was
originally planed but not possible.
The MAC address numbering of the TEW-691GR changes to the following
pattern:
LAN: AA:BB:CC:DD:EE:0C
WIFI: AA:BB:CC:DD:EE:0D
WAN: AA:BB:CC:DD:EE:0F
The MAC address numbering of the TEW-692GR changes to the following
pattern:
LAN: AA:BB:CC:DD:EE:e4
WAN: AA:BB:CC:DD:EE:e5
2.4GHz: AA:BB:CC:DD:EE:e7
5 GHz: AA:BB:CC:DD:EE:e8
Set the label and compatible string for the TEW-692GR PCIe wireless
according to the the PCI binding documentation.
Use the wifi@0,0 label and the pci0,0 compatible string since the PCI
vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the ralink,mtd-eeprom instead of invoking the userspace firmware
loader.
Set the label and compatible string according to the the PCI binding
documentation.
Use the wifi@0,0 label and the pci0,0 compatible string in case the
PCI vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).
This commit might fixes the PCIe wireless for the Buffalo WHR-600D.
This board was mentioned in the board 10-rt2x00-eeprom firmware hotplug
script but never had the correct eeprom name set to trigger the
firmware from flash extraction.
Use the usual eeprom for the soc wmac of the Dovado Tiny AC.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set a device specific wireless mac address for ARV7506PW11, VGV7519 and
VGV7510KW22. The one from the EEPROM is a generic one and the same on
all boards.
Use the wifi@0,0 label and the pci0,0 compatible string for the
ARV7519PW and ARV7525PW since the pci vendor and device id is unknown.
It should work anyway since the compatible string isn't evaluated
(yet).
Signed-off-by: Mathias Kresin <dev@kresin.me>
Backport upstream accepted patch which allows to override the EEPROM
mac address with one from device tree.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The patch 615-rt2x00-fix_20mhz_clk.patch fixes code introduced by
611-rt2x00-rf_vals-rt3352-xtal20.patch and makes the the platform data
property clk_is_20mhz obsolete.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit 519a199cbc.
Multiple users have reported building failures on ARM architectures, e.g.:
In file included from defs.h:42:0,
from process.c:37:
process.c:51:22: error: 'struct user_regs' has no member named 'ARM_r0'
#define uoff(member) offsetof(struct user, member)
^
./linux/arm/userent.h:1:3: note: in expansion of macro 'uoff'
{ uoff(regs.ARM_r0), "r0" },
^
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update to latest Git head in order to import several fixes and enhancements.
- Disable drop invalid by default (FS#73, FS#154)
Instead of dropping packets with conntrack state INVALID, only allow streams
with explicit NEW or UNTRACKED conntrack state.
This change gives user defined rules the chance to accept traffic like ICMPv6
multicast which would be filtered away by the very early ctstate INVALID drop
rule otherwise.
The old behaviour can be restored by explicitely setting "drop_invalid" to 1
in the global firewall config section.
- Fix re-initialization of loadable iptables extensions on musl (FS#31)
Since musl does not implement actual dlclose() semantics, it is impossible to
re-run initializers on subsequent dlopen() calls.
The firewall3 executable now intercepts the extension registration calls
instead in order to be able to re-call them when needed.
This also allowed us to switch to libxtables' builtin extension loader as a
positive side-effect.
- Fix masquerade rules for multiple negated IP addresses (FS#248)
When building MASQUERADE rules for zones which specify multiple negated
addresses in masq_src or masq_dest, emit -j RETURN rules which jump out of
the masquerading chain instead of creating multiple rules with inverted "-s"
arguments.
- Tag own rules using comments
Instead of relying on the nonstandard xt_id match, use the xt_comment match
to mark own rules. Existing comments are prefixed with "!fw3: " while
uncommented rules are marked with a sole "!fw3" string.
This allows removing the xt_id match entirely in a later commit.
- Make missing ubus connection nonfatal
Technically, firewall3 is able to operate without ubus just fine as long as
the zones are declared using "option device" or "option subnet" instead of
"option network" so do not abort execution if ubus could not be connected or
of no network namespace is exported in ubus.
This allows running firewall3 on ordinary Linux systems.
- Fix conntrack requirement detection for indirectly connected zones
The current code fails to apply the conntrack requirement flag recursively to
zones, leading to stray NOTRACK rules which break conntrack based traffic
policing.
Change the implementation to iteratively reapply the conntrack fixup logic
until no more zones had been changed in order to ensure that all directly and
indirectly connected zones receive the conntrack requirement flag.
- Add support for iptables 1.6.x
Adds support for the xtables version 11 api in order to allow building
against iptables 1.6.x
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
"This release fixes a few minor bugs, including a
(non-security-impacting) buffer overflow fix ported
from upstream cjson."
<http://software.es.net/iperf/news.html#iperf-3-1-4-released>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
So far we were displaying "local" which could be misinterpreted. It
wasn't possible e.g. to say if src-link feed was initialized or not.
Hopefully "X" makes (a bit) more sense.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Most of the lantiq devices with ralink wifi have the EEPROM stored
in big endian byte order in flash, but the driver expects the EEPROM to
be in little endian.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The ralink,mtd-eeprom device tree property doesn't require the
ralink,eeprom property to work.
Rework the error handling and user notification as well. Do not log an
error if the mtd-eeprom parameter isn't used. It could be intentional
and should not scare the user.
Check if the number of bytes read from the mtd devices matches the
requested number of bytes.
In case of an mtd read error, give a hint to the user which partition
was tried to read from.
In case everything is fine, notify the user as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Call the rt2x00lib_get_eeprom_file_name only once and from the function
where the EEPROM filename is required.
Error only out if an EEPROM file is mandatory. Use the
REQUIRE_EEPROM_FILE bit to determine if it is mandatory.
Do not set the REQUIRE_EEPROM_FILE bit while requesting an EEPROM file.
It should be (and is) set before requesting an EEPROM file.
Do not redirect users to upstream while using a function of a custom
patch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Because the WAN port is handled by the internal AR8327N switch, the
device should use swconfig_leds trigger to handle the link activity
of the WAN LED. This has the added bonus that the WAN LED will now
go dark if there's no ethernet cable connected to the WAN port.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adds the mac address of the DNS requestor to DNS queries which
are forwarded upstream and can be used to do filtering by the
upstream servers. This only works if the requestor is on the
same subnet as the dnsmasq server
The addmac parameter can hold the following values:
0 : mac address is not added
1 : mac address is added in binary format
base64 : mac address is added base64 encoded
text: : mac address is added in human readable format
as hex and colons
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
moving comgt and its modules to WWAN submenu to join uqmi as both are tools for WWAN modems.
I replaced the link with comgt's ubuntu manpage because the old link isn't working anymore.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
If a package nonshared status is changed, a stale .ipk file might still
be present in the old package directory. Remove the .ipk file from all
package directories when building a new one (or explicitly running
clean)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Package the driver for the DS1374 chip present on the T4240RDB.
Signed-off-by: Florian Larysch <fl@n621.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [fix missing symbol]
For Huawei devices like E3372 proper command for set lte mode is:
AT^SYSCFGEX="03",3fffffff,2,4,7fffffffffffffff,,
Eval is required for proper quotation.
Without this fix:
Fri Nov 4 19:07:49 2016 daemon.notice netifd: Interface 'wan' is setting up now
Fri Nov 4 19:07:52 2016 daemon.notice netifd: wan (2060): sending -> AT
Fri Nov 4 19:07:52 2016 daemon.notice netifd: wan (2060): sending -> ATZ
Fri Nov 4 19:07:53 2016 daemon.notice netifd: wan (2060): sending -> ATQ0
Fri Nov 4 19:07:53 2016 daemon.notice netifd: wan (2060): sending -> ATV1
Fri Nov 4 19:07:54 2016 daemon.notice netifd: wan (2060): sending -> ATE1
Fri Nov 4 19:07:55 2016 daemon.notice netifd: wan (2060): sending -> ATS0=0
Fri Nov 4 19:07:55 2016 daemon.notice netifd: wan (2060): sending -> AT+CGDCONT=1,"IP","internet"
Fri Nov 4 19:07:57 2016 daemon.notice netifd: wan (2060): sending -> AT^SYSCFGEX=\"03\",3fffffff,2,4,7fffffffffffffff,,
Fri Nov 4 19:07:58 2016 daemon.notice netifd: wan (2060): Error running AT-command
Fri Nov 4 19:07:58 2016 daemon.notice netifd: wan (2060): Failed to set operating mode
Fri Nov 4 19:07:58 2016 daemon.notice netifd: wan (2092): Stopping network
...
With this fix:
Fri Nov 4 19:10:59 2016 daemon.notice netifd: Interface 'wan' is setting up now
Fri Nov 4 19:11:01 2016 daemon.notice netifd: wan (2539): sending -> AT
Fri Nov 4 19:11:01 2016 daemon.notice netifd: wan (2539): sending -> ATZ
Fri Nov 4 19:11:02 2016 daemon.notice netifd: wan (2539): sending -> ATQ0
Fri Nov 4 19:11:03 2016 daemon.notice netifd: wan (2539): sending -> ATV1
Fri Nov 4 19:11:03 2016 daemon.notice netifd: wan (2539): sending -> ATE1
Fri Nov 4 19:11:04 2016 daemon.notice netifd: wan (2539): sending -> ATS0=0
Fri Nov 4 19:11:05 2016 daemon.notice netifd: wan (2539): sending -> AT+CGDCONT=1,"IP","internet"
Fri Nov 4 19:11:06 2016 daemon.notice netifd: wan (2539): sending -> AT^SYSCFGEX="03",3fffffff,2,4,7fffffffffffffff,,
Fri Nov 4 19:11:07 2016 daemon.notice netifd: wan (2539): sending -> AT^NDISDUP=1,1,"internet"
Fri Nov 4 19:11:08 2016 daemon.notice netifd: wan (2539): Connected, starting DHCP on wwan0
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan' is now up
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Network device 'wwan0' link is up
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Network alias 'wwan0' link is up
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan_4' is enabled
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan_4' has link connectivity
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan_4' is setting up now
...
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
It's supposed to significantly improve performance but doesn't seem to
affect Northstar unfortunately. It seems only some other platforms were
limited because of this DMA setup mistake.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
FS#256
Fix audio not working due to unset SND_PCM_TIMER. CONFIG_SND_PCM_TIMER
is required for ALSA to work (at least for some audio devices),
otherwise applications using sound may fail. Can be reproduced by
installing "alsa-utils-tests" and running "speaker-test":
...
ALSA lib pcm_direct.c:1159:(snd1_pcm_direct_initialize_poll_fd) unable to open timer 'hw:CLASS=3,SCLASS=0,CARD=0,DEV=0,SUBDEV=0'
ALSA lib pcm_dmix.c:1106:(snd_pcm_dmix_open) unable to initialize poll_fd
Playback open error: -19,No such device
The kernel size does not increase, only the size of the kernel module
increases.
Signed-off-by: Dmitry Sutyagin <f3flight@gmail.com>
The original repo in this Makefile disappeared from the internet so use another
copy of this repository on kernel.org. Also switch from git:// to https://
while being at it.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Port 1 registers the same IO resources as port 2 in the kernel resource
tree, which is wrong.
Fix this by using it's own resources as indicated in the overview
(cns3xxx.h).
Compiled & Tested on several GW2388-4 laguna boards which utilizes all 3
ports.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Christian Lamparter
Eddi De Pieri
Rafał Miłecki
Matthias Schiffer
Jo-Philipp Wich
Marek Lindner
Mathias Kresin
Felix Fietkau
Pavel Kubelun
Henryk Heisig
Roger Pueyo Centelles
Hans Dedecker
BangLang Huang
Alberto Bursi
Christian Schoenebeck
Florian Larysch
Alexandru Ardelean
Cezary Jackiewicz
Dmitry Sutyagin
Koen Vandeputte