Commit Graph

1116 Commits (184c92e7fb9e9cde71e38caf47b99ee3291fdc8e)

Author SHA1 Message Date
John Crispin 2c72ffc154 ar71xx: add support for Netgear WNR2000v4
Signed-off-by: Michaël Burtin <mburtin@gmail.com>

SVN-Revision: 43173
2014-11-03 20:20:56 +00:00
Felix Fietkau a1837135e0 ar71xx: add support for buffalo WZR-450HP2
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43026
2014-10-22 11:02:18 +00:00
John Crispin 6e46fc8a38 wr1043nd-v2: Change .code of the wi-fi button to KEY_RFKILL
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.

Signed-off-by: Josef Gajdusek <atx@atx.name>

SVN-Revision: 42922
2014-10-14 19:01:21 +00:00
John Crispin 99c238ff15 ar71xx: Fix LED definitions for the DRAGINO2 board
This patch fixes LED definitions for the DRAGINO2 board.

1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 42897
2014-10-14 10:33:07 +00:00
John Crispin e2c3c2280c ar71xx: fix reset button gpio for OM2P/OM2P-HS
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".

Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 42782
2014-10-06 04:51:51 +00:00
John Crispin 7dbbdfb61f ar71xx: add qihoo 360 c301 router support
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.

This patch adds its initial support.

v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 42552
2014-09-15 10:19:38 +00:00
Felix Fietkau 60b81acd60 ath79: dev-eth: Don't advertise 1gbit in link code word on ar9331
While the AR9331 has a gigabit MAC towards the internal switch, the
integrated PHYs however are only 100-base-tx capable.  The existing code
however advertieses gigabit capability in the link status word.  If you
attach such a PHY to a gigabit capable switch on the remote end, with
some probability it attempts to negotiate gigabit and fails, falling
baco to the AR9331 assuming a 10mbit half-duplex link.  This has been
observed quite frequently with the Carambola2 and gigabit capable
switches.

In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
for both AR9331 ethernet ports. This is most likely wrong. Despite the
two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
100base-T PHY via MII. The has_gbit attribute is used in the ethernet
driver to determine the supported link modes.

So either pdata->has_gbit is not set to 1 anymore, or the ethernet
driver needs to be modified to determine the advertised link code word
on another criteria than pdata->has_gbit.  This patch implements the
former solution.

Signed-off-by: Harald Welte <laforge@gnumonks.org>

SVN-Revision: 42432
2014-09-07 09:45:32 +00:00
John Crispin 67cf439237 ar71xx: use ETH_ALEN for consistency
Signed-off-by: Forest Crossman <cyrozap@gmail.com>

SVN-Revision: 42280
2014-08-25 06:35:58 +00:00
John Crispin e5e1c03354 ar71xx: TL-WR1043N/ND v2: Fix MAC address of WMAC
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 42193
2014-08-18 13:10:00 +00:00
John Crispin 2c67682192 ar71xx: Fix 2.4G WiFi LED of the OpenMesh MR600 board
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 42184
2014-08-18 13:09:14 +00:00
Imre Kaloz ecba34a3ee add support for the NC-LINK SMART-300
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 42130
2014-08-11 11:44:51 +00:00
Felix Fietkau e41a0cafff ar71xx: add linux 3.14 support
Signed-off-by: Zhao, Gang <gang.zhao.42@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42038
2014-08-07 12:40:53 +00:00
Felix Fietkau b855faecc0 ar71xx: update Carambola2 platform data
Change list:
 * Remove button info on GPIO12, there is no button there.
 * Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.

Tested building for carambola2 target.

Signed-off-by: Mantas Pucka <mantas@8devices.com>

SVN-Revision: 41993
2014-08-04 14:46:52 +00:00
John Crispin e7ec79821a ar71xx: oolite: the buttons are not active_low
this caused factory resets when reboot was pressed

Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41932
2014-08-01 11:19:34 +00:00
Imre Kaloz dc628f2e08 add support for the archer c5
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41814
2014-07-23 12:47:25 +00:00
John Crispin a440524f85 ar71xx: Fix GL.iNet WLAN LED
LED script expects WLAN LED to be "gl-connect:red:wlan".

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 41793
2014-07-21 19:26:46 +00:00
John Crispin eae9b2541a ar71xx: split wndr4300 and wndr3700v4 into 2 seperate mips machines
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41788
2014-07-21 18:41:52 +00:00
John Crispin f424994cbc ar71xx: add kernel support for the OpenMesh OM5P board
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 41769
2014-07-20 17:30:32 +00:00
Gabor Juhos aff3127956 ar71xx: add kernel support for the EnGenius EAP300 v2 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41658
2014-07-14 21:30:26 +00:00
Gabor Juhos 51c892053a ar71xx: add kernel support for the Tube2H board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41649
2014-07-14 16:03:34 +00:00
Gabor Juhos 907bd5345e ar71xx: fix ALFA NETWORK's name
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41643
2014-07-14 11:10:00 +00:00
Gabor Juhos 0bec90b830 ar71xx: add kernel support for the EnGenius ESR900
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5714/
[juhosg:
  - drop nvram.c modifications,
  - create a separate kernel patch,
  - use ath79_setup_qca955x_eth_cfg helper,
  - merge esr900_{010,common}_setup functions,
  - statically init AR8327 pad configurations,
  - use pr_err instead of printk]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41640
2014-07-14 10:25:51 +00:00
Gabor Juhos 26b39cc580 ar71xx: use ath79_setup_qca955x_eth_cfg helper for QCA955x based boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41627
2014-07-13 19:44:00 +00:00
Gabor Juhos 16d45d5531 ar71xx: add kernel support for EnGenius ESR1750
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5840/
[juhosg:
  - fix coding style in mach-esr1750.c,
  - rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41624
2014-07-13 19:43:57 +00:00
Gabor Juhos ee3dfafaf1 ar71xx: add a helper function for setting up ETH_CFG register on QCA955x
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5839/
[juhosg: fix coding style]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41623
2014-07-13 19:43:56 +00:00
Gabor Juhos a46c7d055c ar71xx: allow ath79_nvram_parse_mac_addr parsing mac with quotes
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5838/
[juhosg:
  - fix coding style,
  - check the first and the last character of the MAC string
    instead of using the strchr() function]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41622
2014-07-13 19:43:54 +00:00
Gabor Juhos 9801351c84 ar71xx: add kernel support for GL-Inet V1 boards/routers
The GL-Connect GL.iNet v1 router is basically a TP-Link TL-WR703N with
more DRAM/Flash, 2x Ethernet ports and console/GPIO header in the same
small form-factor:
<http://www.gl-inet.com/w/?lang=en>

Moreover, the manufacturer is promoting the OpenWrt usage to replace
the original firmware and proposing patches against both AA and trunk:
<http://www.gl-inet.com/w/?p=398&lang=en>

This is a clean up of the original manufacturer GPLv2 patch by alzhao,
proposed to the list by Mark Janssen.

Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5273/
[juhosg:
  - remove user-space and image generation support, will be included
    from other patches,
  - fix coding style and drop superfluous comment in mach-gl-inet.c,
  - rename and refresh kernel patch,
  - adjust subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41618
2014-07-13 18:21:04 +00:00
John Crispin 9e26031a88 ar71xx: add support for TP-LINK TL-WA860RE v1
New router/repeater from TP-LINK

- CPU: Atheros AR9341-DL3A (AP123)
- Flash: 4MB
- Ram: 32MB

Similar to TL-WA850RE.

Changes: rename file after r41596

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 41598
2014-07-13 10:03:41 +00:00
John Crispin 42a37b2a89 ar71xx: added support for TL-WA830RE V2
Corrected patch ath79 insted of auth79. Sorry.

Signed-off-by: Fredrik Jonson <fredrik@famjonson.se>

SVN-Revision: 41596
2014-07-13 07:12:22 +00:00
John Crispin 3519322e62 ar71xx: Add support for MikroTik RouterBOARD SXT Lite
This patch adds support for the MikroTik RouterBOARD SXT Lite.

The new RB911L series is also supported as a result.

v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41450
2014-07-01 13:38:30 +00:00
John Crispin 23a9bfc655 ar71xx: r41348 is missing these files
sorry, the downside when applying patches with patch

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41350
2014-06-26 13:47:35 +00:00
John Crispin 680e0c09f3 ar71xx: WNDAP360 adding wifi LED support
I added WIFI LED support (so now AP blinks nicely), I removed WPS
button GPIO (as it doesn't exist) and changed GPIO for reset button.

Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>

SVN-Revision: 40976
2014-06-02 15:02:54 +00:00
John Crispin 05b73eb22f ar71xx: add kernel support for HiWiFi HC6361.
This board manufactured by HiWiFi has the following features.

 - Atheros 9331 SoC.
 - 16MB flash and 64MB RAM.
 - 4GB eMMC storage via SK6226 USB 2.0 controller.
 - 2 LAN and 1 WAN ethernet ports with LEDs on them.
 - 3 blue LEDs on the front panel.
 - 1 button labeled as "reset".
 - Powered by a USB cable.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 40973
2014-06-02 14:56:24 +00:00
John Crispin 60ec05fdcb ar71xx: add support for dlink dir-615-e1
Dlink dir-615-e1 can use dir-600-a1's image, but the image can't be
uploaded through dlink's normal firmware update web page.

Add profile for dir-615-e1 so the generated image can be uploaded
through the firmware update web page.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>

SVN-Revision: 40969
2014-06-02 14:43:35 +00:00
John Crispin c9f15772a1 ar71xx: add kernel support for the OpenMesh OM2P-HSv2
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 40961
2014-06-02 13:21:26 +00:00
John Crispin ef5f37a08d ar71xx: add kernel support for the OpenMesh OM2Pv2 board
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 40955
2014-06-02 13:20:52 +00:00
Felix Fietkau 83dc560621 ar71xx: fix typo in tl-wr710n mac setup (fixes #16469)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 40840
2014-05-24 08:01:33 +00:00
Gabor Juhos 1374e5a721 ar71xx: rb91x: fix ethernet packet loss issues
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.

Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40509
2014-04-13 20:41:52 +00:00
Gabor Juhos a5e398abad ar71xx: add kernel support for ZyXEL NBG 6716
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot

Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
  - rename and refresh kernel patch,
  - fix a few typos,
  - change button key codes,
  - use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40499
2014-04-13 08:29:05 +00:00
Gabor Juhos 4149ab5193 ar71xx: wndr4300: indicate WNDR3700v4 in the kernel support files
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40479
2014-04-12 19:58:23 +00:00
Gabor Juhos 7b85e2e527 ar71xx: wndr4300: enable 5V power for the USB port
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.

Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40478
2014-04-12 19:58:20 +00:00
Gabor Juhos ed72141fd4 ar71xx: wndr4300: use KEY_RFKILL code for the Wireless button
Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40477
2014-04-12 17:53:34 +00:00
Gabor Juhos 4fe71cedfe ar71xx: wndr4300: add LED for 2.4Ghz wifi interface
Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40475
2014-04-12 17:42:35 +00:00
Gabor Juhos db123a8a21 ar71xx: wndr4300: select GPIO_OUT functionality for LED GPIOs
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40474
2014-04-12 17:42:34 +00:00
Gabor Juhos 9b7b57aeb4 ar71xx: wndr4300: change 'orange' to 'amber' in LED color names
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.

Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40473
2014-04-12 17:42:33 +00:00
Felix Fietkau 7131a104f5 ar71xx: add support for the TP-LINK TL-WR841N/ND v9
Everything seems to be working fine. Potential issues:

* VLAN port IDs are reversed with regard to the numbers on the case.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 40400
2014-04-07 08:00:02 +00:00
Felix Fietkau f80f0c7d22 ar71xx: add support for QCA953x SoC
I don't have access to the specs, so I'm not sure about every detail, but I
haven't seen any problems with my test system, a TL-WR841N v9. It looks pretty
much like a QCA955x without PCI, a little twist in the clock calculation and
a AR9331-compatible switch.

Features not yet supported:

* EHCI (my test system doesn't have USB)
* ? (I have no idea if the QCA953x has any other features I don't know about
that aren't used by the TL-WR841N v9)

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 40399
2014-04-07 07:59:45 +00:00
Gabor Juhos 5256bbdc56 ar71xx: add kernel support for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
 - use a separate patch for kernel changes,
 - reorder Kconfig and Makefile entries,
 - change function and variable names to be lowercase only
   and fix misaligned tabs in mach-gs-oolite.c,
   ... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40032
2014-03-27 06:36:46 +00:00
Gabor Juhos 47dfbb5bc6 ar71xx: rb95x: use correct SPI flash address
The flash address passed to rb_init_info() is bogus,
use the predefined AR71XX_SPI_BASE macro instead.

Compile tested only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39891
2014-03-12 12:52:39 +00:00
Gabor Juhos 25e870eed6 ar71xx: ar934x_nfc: fix memory initialization bug
sizeof(array_from_function_definition) gives back the size of the pointer.
sizeof(type)  * array_size   should be used in memset.

Signed-off-by: David Völgyes <david.volgyes@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4950/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39890
2014-03-12 12:52:36 +00:00
Gabor Juhos da2f3c1448 ar71xx: rb91x: register GPIO LEDs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39704
2014-02-23 08:11:53 +00:00
Gabor Juhos 14d95026b2 ar71xx: rb91x: add SPI device for the serial shift register
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.

Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39703
2014-02-23 08:11:52 +00:00
Gabor Juhos 3d906ac6ac ar71xx: rb91x-nand: rewrite to use GPIO API
Rewrite tha rb91x-nand driver to use GPIO API to
modify the NAND control lines.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39700
2014-02-23 07:19:32 +00:00
Gabor Juhos 8fea668cb7 ar71xx: rb91x: register a gpio-latch platform device
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39699
2014-02-22 18:05:32 +00:00
Gabor Juhos 4e0309630b ar71xx: rb91x: fix pll_1000 value for eth0 to avoid packet loss
When the RB91x device uses a GbE link the connection
suffers from packet loss:

  root@OpenWrt:/# ping 192.168.1.254 -s 65507 -c 20 -q
  PING 192.168.1.254 (192.168.1.254): 65507 data bytes

  --- 192.168.1.254 ping statistics ---
  20 packets transmitted, 9 packets received, 55% packet loss
  round-trip min/avg/max = 4.570/4.815/4.999 ms

Using a different PLL value fixes the issue.

  root@OpenWrt:/# ping 192.168.1.254 -s 65507 -c 100 -q
  PING 192.168.1.254 (192.168.1.254): 65507 data bytes

  --- 192.168.1.254 ping statistics ---
  100 packets transmitted, 100 packets received, 0% packet loss
  round-trip min/avg/max = 4.449/5.413/13.870 ms

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39642
2014-02-20 17:07:56 +00:00
Gabor Juhos d19b868b12 ar71xx: Add support for MikroTik RB951Ui-2HnD
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result.  I have cleaned up this patch.

When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.

This patch applies cleanly to SVN 39392.

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
  - drop the 'rb951ui_wlan_init' function and rework the code to
    use the recently introduced rb95x_wlan_init function instead,
  - fix GPIO number of the port5 LED,
  - rename LEDs according to the standard LED naming conventions,
    and use 'rb' prefix in the names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39641
2014-02-20 17:07:51 +00:00
Gabor Juhos db0e6e264d ar71xx: add kernel support for the TP-Link TL-WDR4900 v2.0 board
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4848/
[juhosg:
  - rename and refresh kernel patch,
  - merge the board setup code into mach-archer-c7.c and drop
    mach-tl-wdr49000-v2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39635
2014-02-19 12:15:32 +00:00
Gabor Juhos 3b8c51771d ar71xx: wpe72: set active_low flag for the reset button
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39401
2014-01-26 14:55:34 +00:00
Gabor Juhos b503dc026e ar71xx: wp543: set active_low flag for the buttons
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39400
2014-01-26 14:55:32 +00:00
Gabor Juhos 50f38063cd ar71xx: archer c7: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39395
2014-01-25 11:16:59 +00:00
Gabor Juhos f85231257e ar71xx: fix bad RX sensitivity on newer TL-WDR4300 boards
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.

Setup the GPIOs of the external LNAs to fix the issue.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39392
2014-01-24 17:40:17 +00:00
Gabor Juhos b629009eaa ar71xx: wp543: use KEY_RESET code for the sw4 button
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39374
2014-01-23 12:23:08 +00:00
Gabor Juhos 0b599c51cc ar71xx: mynet-n750: define LEDs connected to the AR8327 switch
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4743/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39361
2014-01-21 17:17:42 +00:00
Gabor Juhos 506b40b628 ar71xx: tl-wr1043nd-v2: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39346
2014-01-20 10:23:06 +00:00
Gabor Juhos c17cfab560 ar71xx: tl-wdr4300: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39345
2014-01-20 10:23:05 +00:00
Gabor Juhos 4c54635106 ar71xx: rb2011: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39341
2014-01-20 10:23:01 +00:00
Gabor Juhos b4dc45e07d ar71xx: rb2011: fix eth5 LED
The eth5 LED on the RB2011 is not working because the
LED control rule is missing. Fix it.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39335
2014-01-20 10:22:49 +00:00
Gabor Juhos c977d49a29 ar71xx: my net n750: simplify LNA GPIO setup
Use the ath79_wmac_set_ext_lna_gpio helper instead
of exporting the GPIOs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39217
2014-01-10 09:37:59 +00:00
Gabor Juhos cc3beb9c76 ar71xx: my net n600: simplify LNA GPIO setup
Use the ath79_wmac_set_ext_lna_gpio helper instead
of exporting the GPIOs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39216
2014-01-10 09:37:58 +00:00
Gabor Juhos 32aef686f7 ar71xx: Fix WD My Net N600 weak signal issue
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.

Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Patchwork: http://patchwork.openwrt.org/patch/4689/
[juhosg:
  - remove the GPIO LED changes, the My Net N600 has no yellow LEDs at all,
  - change subject and update the commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39214
2014-01-10 09:07:12 +00:00
Gabor Juhos 01727717f7 ar71xx: Fix WD My Net N750 weak signal issue
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.

Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4688/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39213
2014-01-10 09:07:11 +00:00
Gabor Juhos 05f8604e2e ar71xx: fix max frame length of the QCA955x SoCs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39161
2013-12-23 17:05:23 +00:00
Gabor Juhos 76f37c5d46 ar71xx: don't set builtin_switch flag for QCA9558
It makes no sense, the SoC has no built-in switch.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39160
2013-12-23 17:05:21 +00:00
Gabor Juhos f2cd3399f7 ar71xx: allow to use large ethernet frames on AR934x SoCs
The hardware supports large ethernet frames. Override
the maximum frame length and packet lenght mask in the
platform data to allow to use large MTU on the ethernet
interfaces.

Limit the feature to AR934x SoCs for now. It should work
on some other SoCs as well, but those has not been tested
yet.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39149
2013-12-20 11:41:23 +00:00
Gabor Juhos 2c4e3cf33a ar71xx: ag71xx: get max_frame_len and desc_pktlen_mask from platform data
This will allow to use SoC specific values for both.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39145
2013-12-20 11:41:17 +00:00
Gabor Juhos 1ebf211340 ar71xx: fix WD My Net N750 switch led cfg
Now that the switch is working correctly I had the chance to actually
test the LED config.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4616/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39129
2013-12-17 22:14:12 +00:00
Gabor Juhos c72313fd98 ar71xx: implement switch fix for WD My Net N750
The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.

This fix implements just that.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39128
2013-12-17 22:14:11 +00:00
Gabor Juhos 8b712436f3 ar71xx: implement callback in mdio reset
This enables us to add fixups to the board specific code for boards that
require special treatment of PHYs on mdio bus reset.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
http://patchwork.openwrt.org/patch/4614/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39127
2013-12-17 22:14:10 +00:00
Gabor Juhos ba860e4c3a ar71xx: make ag71xx_mdio_platform_data visible
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39126
2013-12-17 22:14:07 +00:00
Gabor Juhos 5237a50089 ar71xx: add initial support for the Mikrotik RB911G/RB912UAG boards
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39102
2013-12-16 18:08:51 +00:00
Gabor Juhos d7a0184446 ar71xx: rb2011: use board name from the hardware config
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39096
2013-12-16 12:41:48 +00:00
Gabor Juhos 26ca95fefa ar71xx: rb2011: simplify setup code
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39095
2013-12-16 10:28:42 +00:00
Gabor Juhos 59b6cf1e70 ar71xx: rb2011: use the new RouterBOOT helpers
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39094
2013-12-16 10:28:41 +00:00
Gabor Juhos 627651dfca ar71xx: rb95x: use the rb_get_wlan_data helper
Also remove unused RB_* defines.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39092
2013-12-16 10:11:02 +00:00
Gabor Juhos 16565ec94b ar71xx: add some RouterBOOT specific helper functions
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39091
2013-12-16 10:11:01 +00:00
Gabor Juhos 728c2c6cff ar71xx: rb95x: nuke rb95x_gpio_init
Set up the chipselect GPIO directly in rb95x_nand_init
instead.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39087
2013-12-16 08:17:40 +00:00
Gabor Juhos 3dc1cbb167 ar71xx: add kernel support for WD My Net N750
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: use a separate patch for kernel changes]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39077
2013-12-16 07:16:42 +00:00
Gabor Juhos fd393c0b05 ar71xx: add kernel support for the TL-WA901ND v3 board
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39073
2013-12-15 21:34:18 +00:00
Gabor Juhos 9ce06f2ac8 ar71xx: move TL-WA801ND v2 setup code
The TL-WA801ND v2 board has only one LAN port which makes
it more similar to the TL-WR[78]50RE devices. Move the
board setup code into the mach-tl-wax50re.c file.

Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39072
2013-12-15 21:34:17 +00:00
Gabor Juhos 40f081ad08 ar71xx: refactor TL-WAx50RE setup code
This way it is a bit easier to add other TP-LINK devices based on the
Atheros AP123 reference board with one LAN port.

Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39071
2013-12-15 21:34:15 +00:00
Gabor Juhos e3e559fd52 ar71xx: add kernel support for the TL-WA801ND v2 board
Patch to add kernel support for the TP-LINK WA801ND v2

Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4500/
[juhosg:
  - the TL-WA801ND v2 does not have a sliding switch, it uses a push button
    for WPS instead. Use the tl_mr3420v2_gpio_keys array to reflect that,
  - rename kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39063
2013-12-15 20:39:10 +00:00
Felix Fietkau 7a260c3620 ath9k: merge initval and tx gain table updates, calibration fixes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39001
2013-12-08 14:48:30 +00:00
Gabor Juhos bc2d7b8193 ar71xx: add kernel support for the TL-WR1043ND v2 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38955
2013-11-29 20:51:12 +00:00
Gabor Juhos 981e3b354a ar71xx: improve support for the My Net Wi-Fi Range Extender device
This patch improves support for the device considerably.

1. The wifi didn't work in the initial release. This was because
the WMAC of the AR9340 is not connected to the antennas.
(However, it can pick up wifi signals, if they are strong enough!)
Instead there's a dedicated AR9300 chip on the same board, which
works.

2. Ethernet throughput is improved. iperf shows that the hardware
can sustain more than 200Mbit/s and no longer drops any packages
when the link is under load.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4461/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38949
2013-11-29 20:18:44 +00:00
Gabor Juhos af4873e41c ar71xx: Kernel support update tl-wr842n_v2 added missing usb led
Just a small oversight my part, added the support for the USB led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>

Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4425/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38946
2013-11-29 20:18:40 +00:00
Gabor Juhos 625cf61c5b ar71xx: Add kernel support for the WR842N/ND v2
Patch to add kernel support for the TP-LINK WR842N/ND v2

Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4352/
[juhosg: refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38813
2013-11-15 10:11:20 +00:00
Gabor Juhos 25756c61bc ar71xx: Use KEY_RESTART key code for the reset button on WD My Net N600 boards
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38720
2013-11-11 08:10:02 +00:00
Gabor Juhos 79163c8919 ar71xx: Add kernel support for the TP-Link WA750RE / WA850RE range extender
Patch to add kernel support for the TP-LINK WA750RE and the WA850RE
range extender

Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
[juhosg: rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38717
2013-11-11 08:04:46 +00:00
Gabor Juhos ece1323ed4 ar71xx: add kernel support for the My Net Wi-Fi Range Extender device
This patch adds a new device definition for a
Western Digital device. The hardware seems to
be based on Qualcomm Atheros DB120 design.

Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[juhosg: refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38686
2013-11-07 22:31:52 +00:00
Gabor Juhos ef8306cfd2 ar71xx: add kernel support for BHU Networks BXU2000n-2 A1 board
BXU2000n-2 A1 is a BHU Networks WLAN board, use ar9341 chip.

Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
[juhosg:
  - rename and refresh kernel patch,
  - fix some checkpatch warnings and adjust whitespaces in
    mach-bhu-bxu2000n2-a.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38591
2013-10-30 06:50:57 +00:00
Gabor Juhos 22b5040c64 ar71xx: add kernel support for the Sitecom WLR-8100 wireless router
- unsure about copyright message
  - based on AP136-010

Patchwork: http://patchwork.openwrt.org/patch/4147/
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
[juhosg: rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38589
2013-10-30 06:50:54 +00:00
Gabor Juhos 7074bb286d ar71xx: add kernel support for DRAGINO2
This patch adds support for DRAGINO2 board (used by
Meshpotato v2). Most of the files included can be
found in the official svn repository provided by the
company [1]. I have just adapt it to the last OpenWrt
trunk revision (Fri Oct 4 10:49:47 2013).

 1. http://svn.dragino.com/dragino2

Patchwork: http://patchwork.openwrt.org/patch/4234/
Signed-off-by: Pau Escrich <p4u@dabax.net>
[juhosg:
 - rename and refresh kernel patch,
 - fix checkpatch warnings in  mach-dragino2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38587
2013-10-30 06:50:52 +00:00
Gabor Juhos 68e13de37d ar71xx: fix WLAN 5 GHz LED init on dir-825-c1
Fixes the 5 GHz LED.

The same function has no effect on the 2.4 GHz LED at all, so we might
as well remove it.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38482
2013-10-20 15:59:04 +00:00
Gabor Juhos f8aef84e49 ar71xx: improve kernel support for the TL-MR3040 v2
This patch adds support for the hardware slide switch on
the TL-MR3040 v2.

Signed-off-by: Mads Hansen <d@taba.se>
[juhosg: use EV_SW instead of EV_KEY]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38190
2013-09-25 18:42:10 +00:00
Gabor Juhos 8b920136a0 ar71xx: add kernel support for the TEW-732BR board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38131
2013-09-23 09:49:01 +00:00
Gabor Juhos d661af0b77 ar71xx: vanity changes for dir-825-c1
This patch

- changes the color names from orange to amber
- changes the name of GPIO 13 from WIFI_BGN (wifi_bgn) to WLAN_2G
  (wlan2g) to be more consistent with the other routers' files
- changes the descriptions of the hardware keys to be a tad more
  explicit

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4081/
[juhosg: update the LED migration script as well]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38105
2013-09-21 16:08:44 +00:00
Gabor Juhos 0a813e9e3c ar71xx: use netgear prefix for WNDAP360 LED names
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38102
2013-09-21 15:55:55 +00:00
Gabor Juhos d0fe16cedf ar71xx: use netgear prefix for WNR612 v2 LED names
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38101
2013-09-21 15:55:54 +00:00
Gabor Juhos ae7d14f701 ar71xx: use netgear prefix for WNR2200 LED names
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38100
2013-09-21 15:55:52 +00:00
Gabor Juhos 87f7ac6b4e ar71xx: use netgear prefix for WNR2000 LED names
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38099
2013-09-21 15:55:51 +00:00
Gabor Juhos e33ccdc295 ar71xx: use netgear prefix for WNDR3700 LED names
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38098
2013-09-21 15:55:50 +00:00
Gabor Juhos 10ed605a89 ar71xx: let HW switch control WAN LED on dir-825-c1
Enable GPIO 20. This hands off control of the blue planet led to the
integrated switch. Consequently, remove the led configuration for the
blue planet led.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4080/
[juhosg: whitespace fixup]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38096
2013-09-21 14:56:24 +00:00
Gabor Juhos 50f4732438 ar71xx: fix LAN LEDs for dir-825-c1
This patches fixes the lan led configuration. The new configuration is
identical to the one in mach-db120.c and it works. The previous one
didn't work at all.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38094
2013-09-21 12:04:45 +00:00
Gabor Juhos 1dd33c4d6c ar71xx: tew-712br: use ath79_parse_ascii_mac helper
Remove the local MAC address parser function and use
the generic one instead.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38090
2013-09-20 16:41:36 +00:00
Gabor Juhos cb18e38996 ar71xx: tew-673gru: use ath79_parse_ascii_mac helper
Remove the local MAC address parser function and use
the generic one instead.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38089
2013-09-20 16:41:34 +00:00
Gabor Juhos a98df83f5f ar71xx: dir-825-c1: use ath79_parse_ascii_mac helper
Remove the local MAC address parser function and use
the generic one instead.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38088
2013-09-20 16:41:33 +00:00
Gabor Juhos 710314990a ar71xx: dir-825-b1: use ath79_parse_ascii_mac helper
Remove the local MAC address parser function and use
the generic one instead.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38087
2013-09-20 16:41:32 +00:00
Gabor Juhos 2a777a272c ar71xx: dir-505-a1: use ath79_parse_ascii_mac helper
Remove the local MAC address parser function and use
the generic one instead.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38086
2013-09-20 16:41:31 +00:00
Gabor Juhos e312a917d3 ar71xx: rename ath79_parse_mac_addr to ath79_parse_ascii_mac
Rename the function and extend it in order to make it
usable from board setup code.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38085
2013-09-20 16:41:30 +00:00
Gabor Juhos 9a2e94476a ar71xx: add kernel support for the WD My Net N600 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38072
2013-09-19 22:36:39 +00:00
Gabor Juhos 9200807877 ar71xx: wndr4300: enable HW ECC mode for the NAND controller
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38071
2013-09-19 18:43:43 +00:00
Gabor Juhos 83915a8d78 ar71xx: add ath79_nfc_set_ecc_mode helper
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38070
2013-09-19 18:43:42 +00:00
Gabor Juhos e3e31835ae ar71xx: add kernel support for TP-Link TL-MR13U
This patch adds support for TP-Link TL-MR13U router with built-in 10AH
rechargeable battery.

The patch is based on kamwanlai's patch:
https://forum.openwrt.org/viewtopic.php?pid=206746#p206746

Updated to accommodate recent changes introduced with:
ar71xx: remove fs_* variables from image/Makefile

Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4063/
[juhosg:
  - refresh and rename rename 930-add-tl-mr13u-support.patch =>
    625-MIPS-ath79-add-tl-mr13u-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38063
2013-09-19 17:52:41 +00:00
Gabor Juhos 5e23012c77 ar71xx: wnr2200: fix a typo in a LED name
Reported-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38062
2013-09-19 17:52:40 +00:00
Gabor Juhos 49ed06e36f ar71xx: add kernel support for Netgear WNR2200 wireless router
This patch adds OpenWRT support for the Netgear WNR2200 (N300)
wireless router with USB.

Technical details of this router can be found at
http://www.netgear.com/home/products/wirelessrouters/work-and-play/WNR2200.aspx
and http://wikidevi.com/wiki/Netgear_WNR2200

Signed-off-by: Aidan Kissane <aidankissane@googlemail.com>
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4055/
[juhosg:
  - add commit message and SoB line from the original patch
  - remove dead code from mach-wnr2200.c
  - refresh 624-MIPS-ath79-WNR2200-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 38059
2013-09-19 16:56:48 +00:00
Gabor Juhos 897c00c145 ar71xx: add wireless bgn led support for dir-825-c1
I checked the GPL code drop from D-Link and tried to get the wireless
and LAN switch LEDs to light up. I found some references in
AthSDK/www/DIR-825_C1/bsp.h as well as
AthSDK/www/DIR-825_C1/rootfs/etc/sysconfig/S2gpio.sh, but in the end I
only got the led for 2.4GHz to work. Anyway, here's the patch.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37963
2013-09-13 15:01:40 +00:00
Gabor Juhos 122a61aa49 ar71xx: configure OBS4 line on TL-WR841N-v8/MR3420v2
It also fixes USB Power on MR3420v2.

This time we took the information from the source of GPL:
http://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg18970.html
Confirmed and tested:
https://dev.openwrt.org/ticket/13201#comment:41
Thanks to oguretsagressive for testing.

Signed-off-by: Dmytro <dioptimizer@gmail.com>

SVN-Revision: 37878
2013-09-02 16:09:12 +00:00
Gabor Juhos 9af6a5a88f ar71xx: don't register USB device on WNDAP360
Apparently registering usb device on newest trunk causes
this AP not to boot...
Since there is no USB socket in that device anyway this
can be simply removed (and device boots then no problem).

[juhosg:
  - tweak subject line and description,
  - remove #include "dev-usb.h",
  - remove 'select ATH79_DEV_USB' from Kconfig]

Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37844
2013-08-27 10:48:24 +00:00
John Crispin 553a469728 ar71xx: add support for dir 505 a1
this patch is based on ...

-> https://forum.openwrt.org/viewtopic.php?pid=179902#p179902

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 37703
2013-08-05 10:41:48 +00:00
Gabor Juhos 99a12119ca ar71xx: fix tl-wa901nd buttons code
This patch fixes the code of the buttons for TP-Link WA901ND.

Signed-off-by: Rocco Folino <lordzen@autistici.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37696
2013-08-05 09:09:39 +00:00
Gabor Juhos 6d8163505e ar71xx: add kernel support for the Netgear WNR612 v2 board
Netgear WNR612 v2:
 - cpu Atheros AR7240 (Python) @400MHz
 - flash 4MB
 - ram 32MB
 - ethernet 10/100: 1xwan + 2xlan (only two)
 - radio AR9285

[juhosg: use a separate kernel patch]

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3876/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37575
2013-07-28 10:23:36 +00:00
Gabor Juhos c5029c2ebf ar71xx: add kernel support for the TP-LINK TL-WR710N v1 board
Small router sold in EU: AR9330@400MHz, 1x USB2.0,
2x ethernet, 8MB flash, 32MB ram, one led, one button.

See: http://galeria.tech-blog.pl/TP-Link_TL-WR710N-EU/

[juhosg: use a separate kernel patch]

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3873/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37572
2013-07-28 10:23:32 +00:00
Gabor Juhos b49dc036e8 ar71xx: TEW632BRP has buttons 'active low', fix board config
Looks like trunk@37090 has changed the logic that determines
if router's button was pressed. This resulted in TEW632BRP
always booting into failsafe mode because it detected pressed
button (which was not pressed).

Measure with voltmeter has shown that buttons on this router
are actually active-low. This patch reflects this fact in
board configuration and fixes 'load info failsafe mode' issue.

Note: it looks like Trendnet TEW632BRP and a close relative
to TEW-652BRP V1.0 and D-Link DIR-615C1, so same problem may
exist on those routers as well. This patch doesn't affect
routers other than 632BRP and unfortunately I do not have
hardware to test this issue with other routers.

This patch fixes #13893 and is tested on actuall Trendnet
TEW632BRP.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37569
2013-07-28 10:23:22 +00:00
Gabor Juhos ec7fe3fab7 ar71xx: add kernel support for the TL-MR10U board
Based on andelf's patch:
http://andelf.diandian.com/post/2013-05-22/40050677370

[juhosg: extend WR703N code to handle the TL-MR10U
instead of adding a separate mach-tl-mr10u file]]

Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3840/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37547
2013-07-26 07:31:57 +00:00
Felix Fietkau 25d910a78f ar71xx: use uimage split for WZR-HP-G300NH2
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 37295
2013-07-14 14:05:31 +00:00
Felix Fietkau 6bff456212 ar71xx: enable uimage split for wzr-hp-ag300h/wzr-600dhp
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 37294
2013-07-14 14:05:27 +00:00
Felix Fietkau fbde376c53 ar71xx: use uimage split for WZR-HP-G300NH
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 37293
2013-07-14 14:05:23 +00:00
Felix Fietkau a7c5f6708b ar71xx: use uimage split for WZR-HP-G450H
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 37292
2013-07-14 14:05:19 +00:00
John Crispin 39531131a9 ar71xx: add carambola2 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 37260
2013-07-11 21:16:53 +00:00
Gabor Juhos e61a77a05c ar71xx: disable JTAG on TL-WR841N-v8/MR3420v2
It also fixes USB Power on MR3420v2.

Signed-off-by: Dmytro <dioptimizer@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37194
2013-07-08 08:40:21 +00:00
Gabor Juhos ca02639d17 ar71xx: fix for wrong eth0 mac assignment on Netgear WNDAP360
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37192
2013-07-08 08:40:18 +00:00
Luka Perkov c9926f77b4 ar71xx: Buffalo WZR-HP-AG300H (600DHP) change button type
switch buttons should be declared as switch so the failsafe shell is not
triggered by accident in procd

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 37131
2013-07-02 10:45:32 +00:00
Gabor Juhos 5bb2e8030d ar71xx: add support for WIFI button on tp-link tl-mr3220v2
The TP-LINK TL-MR3220 v2 has a button on the left side
labeled "WIFI". This is GPIO 24. This patch adds the
support for this button.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36848
2013-06-04 13:25:54 +00:00
Gabor Juhos da66ea52ec ar71xx: register USB port for RB2011U* devices
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36801
2013-05-30 17:38:31 +00:00
Gabor Juhos 151dca0935 ar71xx: make the SFP port usable on RB2011*S boards
The port 6 of the switch is connected to the SFP
cage on the RB2011*S boards. Add a helper function
to correctly initialize the switch configuration
data on those boards to make the SFP port usable.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36799
2013-05-30 17:38:28 +00:00
Gabor Juhos 3467b17e69 ar71xx: rb2011: add switch led control values
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36796
2013-05-30 17:38:21 +00:00
Gabor Juhos 4cf6e53ccc ar71xx: rb2011: update RGMII RX/TX delay values
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36795
2013-05-30 17:38:20 +00:00
Gabor Juhos 6da63a8793 ar71xx: rb2011: move NAND nCE init to rb2011_nand_init
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36794
2013-05-30 17:38:17 +00:00
Gabor Juhos d6554bf66a ar71xx: add kernel support for the RB2011UAS
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36792
2013-05-30 17:38:13 +00:00
Gabor Juhos 91d7c3efc1 ar71xx: add kernel support for the TP-LINK Archer C7 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36788
2013-05-30 16:23:07 +00:00
Gabor Juhos 93ce462b7e ar71xx: set eth0 mac address to match bottom label of the OM2P LC
Signed-off-by: marek@open-mesh.com
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36723
2013-05-26 16:02:29 +00:00
Felix Fietkau 144cfb65a4 ar71xx: add hard_cfg offset detection for rb2011 support - fixes wlan on some newer devices
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 36631
2013-05-13 19:13:33 +00:00
Gabor Juhos 10b3ca5ccb ar71xx: add kernel support for Netgear WNDAP360
Here is corrected version (only thing not working are wifi LEDs).

[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]

Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36578
2013-05-08 17:03:34 +00:00
Gabor Juhos 9b3c0d11a2 ar71xx: Add Netgear WNR2000v3 support
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.

Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36459
2013-04-26 17:00:52 +00:00
Gabor Juhos 5c11773f8a ar71xx: add kernel support for TPLINK WR720N v3
Add support for TPLINK WR720N v3 which has 4MB flash,
32MB ram, 2 ethernet interfaces, 1 USB 2.0 port.

The patch is mostly a modification from mach-tl-wr703n.c.
GPIO numbers for the slider switch is from mach-tl-mr3020n.c.

Tested on my device and they worked fine.

Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36456
2013-04-26 17:00:48 +00:00
Gabor Juhos f7da2127ab ar71xx: fix ethernet LEDs on the TL-WDR3500
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36122
2013-03-25 06:40:03 +00:00
Gabor Juhos cd5cca4ba8 ar71xx: fix USB power GPIO on the TL-WDR3500
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36119
2013-03-24 19:23:47 +00:00
Gabor Juhos 4daefc9480 ar71xx: remove numeric suffix of the TL-WDR3500 USB LED
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36118
2013-03-24 19:23:45 +00:00
Gabor Juhos 35d41db979 ar71xx: rw2458n - Use eeprom (art) from wifi card
Use eeprom (art) from included wifi card, not hard coded in flash.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36037
2013-03-15 14:35:50 +00:00
Gabor Juhos 8deffcba7e ar71xx: Error fix in Kernel for MR3420v2 Ethernet Switch configuration
Error in using another MDIO (AP123 platform using only one GE1 device
for eth0 and eth1) for the router mr3420v2.
?onfirmed: https://forum.openwrt.org/viewtopic.php?pid=194779#p194779

Routers in this sense are the same and the only difference is: USB
port, USB led, instead of the GPIO-switch we have GPIO-button.

Signed-off-by: Dmytro <dioptimizer@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36036
2013-03-15 14:35:48 +00:00
Gabor Juhos 14ca5fc98b ar71xx: om2p-hs: use correct bit mask to disable JTAG functionality
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35966
2013-03-11 19:52:54 +00:00
Gabor Juhos 902dd27383 ar71xx: add kernel support for MR3420v2
[juhosg: use gpio_request_one to enable the USB power]

Patch-by: Dmytro <dioptimizer@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@opewrt.org>

SVN-Revision: 35961
2013-03-11 15:55:20 +00:00
Gabor Juhos 5c5e1c0a9d ar71xx: enabling control GPIO14 and GPIO15 on MR3040/MR11U
LAN1 and LAN2 LEDs not present (it pulled to ground via
resistors) on MR3040 and MR11U devices. This little patch
enabling ability to control GPIO14 and GPIO15.

Patch-by: Dmytro <dioptimizer@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3439/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35960
2013-03-11 15:55:19 +00:00
Gabor Juhos a7525f5f5d ar71xx: add kernel support for dir-835-a1
[juhosg:
  - remove custom mdio bus info and platform data for ar8327, clear the
    .led_cfg field from dir835a1_setup instead,
  - remove arguments of dir835c1_generic_setup function, register the
    LEDs directly from the board specific setup instead]

Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Patchwork: http://patchwork.openwrt.org/patch/3426/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35957
2013-03-11 15:55:13 +00:00
Gabor Juhos 1d55249d7c ar71xx: use backported QCA955x patches
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35878
2013-03-04 11:48:15 +00:00
Luka Perkov a5ebfc79ba ar71xx: rework changes from r35840
Signed-off-by: Luka Perkov <luka@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35865
2013-03-03 21:59:34 +00:00
Gabor Juhos 4491da2bd4 ar71xx: update MAC address assignment for dir-825-c1
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35855
2013-03-03 12:47:37 +00:00
Gabor Juhos 200aa6db83 ar71xx: fixes leds for dir-825-c1
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35854
2013-03-03 12:47:33 +00:00
Luka Perkov 107e0c6d1f ar71xx: add support for Buffalo WZR 600DHP
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 35840
2013-03-01 13:46:01 +00:00
Gabor Juhos bcac3c5569 ar71xx: fix MAC address assignment on the DIR-825-Bx boards
Use the same MAC addresses as the original firmware.

Based on a patch from #10421.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Tested-by: Gabor Varga <vargagab@gmail.com>

SVN-Revision: 35730
2013-02-21 17:58:21 +00:00
Gabor Juhos 4341b11f3e ar71xx: remove __dev{init,exit} annotations from kernel files
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35687
2013-02-19 20:52:06 +00:00
Gabor Juhos 7a709573d7 ar71xx: add kernel support for the Mikrotik RB951G board
This is platform definition for the RB951G device. It's mostly rework
of RB2011UAS patchset with network taken from the RB751 patches.
The main difference is the flash layout used by this device.

[juhosg:
  - remove dead code from mach-rb951g
  - add "-2HnD" suffix to the machine name
  - use a separate 615-MIPS-ath79-RB951G-support.patch]

Patchwork: http://patchwork.openwrt.org/patch/3257/
Signed-off-by: Kamil Trzcinski <ayufan@ayufan.eu>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35633
2013-02-17 10:08:35 +00:00
Jonas Gorski f07a33afc2 ar71xx: register the micro sd card reader on RB493G
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 35535
2013-02-10 12:31:38 +00:00
Gabor Juhos 6ff973bdda ar71xx: Routerboard 751 Mac Address Offset Fix
We utilize many Routerboard 751's and discovered that our latest batch
of RB751's would not initialize the wireless radio. We have determined
Mikrotik has changed where the mac address was located inside hardconfig.
As such we utilize "routerboot_find_tag" to find the location of the mac
address. We should remove "RB751_MAC_ADDRESS_OFFSET" as it is ambiguous
by machine manufacturing date. The newer batch of RB751's that we received
had a RB751_MAC_ADDRESS_OFFSET 0x10.

Signed-off-by: Davey Hutchison <dhutchison@bluemesh.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35519
2013-02-08 09:34:53 +00:00
Gabor Juhos 7c87d28054 ar71xx: fixes whitespaces for dir-825-c1
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35455
2013-02-02 15:02:19 +00:00
Gabor Juhos 31af0dc186 ar71xx: fix mac address calculation on the OpenMesh MR600
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35446
2013-02-02 08:47:41 +00:00
Gabor Juhos 8837d3a49b ar71xx: add kernel support for the OpenMesh MR600v2
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35428
2013-02-01 15:50:42 +00:00
Gabor Juhos fe3db74276 ar71xx: remove unused OpenMesh MR6000 platform code
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35426
2013-02-01 15:50:37 +00:00
Gabor Juhos 5bd02ca895 ar71xx: add kernel support for the TL-WDR3500 board
WDR3500 is similar to WDR3600 except it doesn't have gigabit ethernet,
and has only 1 USB port.

Pending issues:

  * Leds are not working at all (except power and wlan_5g)
  * LAN switch ethernet ports are reversed with respect to case label.

  [Label] -> soft device
  [LAN1] -> eth0.4
  [LAN2] -> eth0.3
  [LAN3] -> eth0.2
  [LAN4] -> eth0.1

Based on http://patchwork.openwrt.org/patch/3208/

Thanks-to: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35423
2013-02-01 15:50:29 +00:00
Gabor Juhos 800da21cb1 ar71xx: add kernel support for dir-825-c1
[juhosg:
 - remove unused GPIO stuff
 - use a separate kernel patch for machine integration]

Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35401
2013-01-29 22:50:50 +00:00
Gabor Juhos 5ca187570f ar71xx: add kernel support for Atheros AP132 Reference Board
Based on http://patchwork.openwrt.org/patch/3162/

Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35395
2013-01-29 19:12:30 +00:00
Gabor Juhos 8a9d92f125 ar71xx: fix ethernet device registration for the QCA9556 SoC
Based on http://patchwork.openwrt.org/patch/3162/

Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35394
2013-01-29 19:12:28 +00:00
Gabor Juhos df15e5cd61 ar71xx: enable fast flash read on dual-flash devices
This improves flash read speed on various Buffalo units.

mtd_speedtest results on the WZR-HP-AG300H:

                          old         new        delta
eraseblock read speed:  726 KiB/s   2068 KiB/s   +184.85%
page read speed:        699 KiB/s   1973 KiB/s   +182.26%
2 page read speed:      711 KiB/s   2043 KiB/s   +187.34%

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35392
2013-01-29 19:12:25 +00:00
Gabor Juhos ba4de984b9 ar71xx: disable PHY_SWAP and PHY_ADDR_SWAP bits on TL-WR703N/MR3020/MR3040/MR11U boards
The PHY_SWAP and PHY_ADDR_SWAP bits are initialized
differently by different versions of the bootloader.
This leads to broken ethernet connection with OpenWrt
on some boards.

Turn both SWAP bits OFF on these boards to make it
consistent regardless of the bootloader used.

Based on a patch by Michel Stempin <michel.stempin@wanadoo.fr>.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35037
2013-01-07 14:30:37 +00:00
Gabor Juhos 66efec6783 ar71xx: allow to register the NAND flash controller on the QCA955x
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34945
2013-01-01 13:10:36 +00:00
Gabor Juhos 5dec87afef ar71xx: fix ethernet device registration for QCA9558
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34853
2012-12-22 12:12:48 +00:00
Gabor Juhos 4085a5773d ar71xx: fixup allowed PHY interface types for QCA9558
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34851
2012-12-22 12:12:44 +00:00
Gabor Juhos f01a786825 ar71xx: don't assign any MII bus device on QCA9558 by default
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34850
2012-12-22 12:12:43 +00:00
Gabor Juhos a0b31f97bb generic: ar8216: rename cpuport_cfg to port0_cfg in ar8327_platform_data
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34846
2012-12-22 12:12:35 +00:00
Gabor Juhos 0767605d17 ar71xx: add kernel support for the TL-MR3220 v2
Based on the following patch:
http://patchwork.openwrt.org/patch/3043/

[juhosg:
 - remove custom LED and button arrays
 - use separate machine specific patch
 - update Kconfig]

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34779
2012-12-19 08:50:35 +00:00
Gabor Juhos bc82db7d78 ar71xx: add kernel support for the NETGEAR WNDR4300
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34647
2012-12-12 16:49:49 +00:00
Gabor Juhos 75b71f4a74 ar71xx: add ap91_pci_init_simple helper
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34646
2012-12-12 16:49:48 +00:00
Gabor Juhos 1f7ae58a2c ar71xx: ar934x_nfc: allow to control DMA data swap via platform data
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34588
2012-12-10 10:38:07 +00:00
Gabor Juhos d44d954dec ar71xx: add kernel support for the RB435G board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34239
2012-11-18 10:18:01 +00:00
Gabor Juhos d62bddc620 ar71xx: update PCI IRQ map for RB4xx devices
Should fix #12269.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34238
2012-11-18 09:51:04 +00:00
Gabor Juhos 8d4857d677 ar71xx: add kernel support for the OpenMesh MR600 board
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34231
2012-11-18 09:32:33 +00:00
Gabor Juhos 91bab828aa ar71xx: add support for TP-Link TL-WA7510N
It is mostly the same as TL-WA901N. WLAN and LAN
are working. LAN LED is working. WLAN signal
strength LEDs are not working yet.

http://wiki.openwrt.org/toh/tp-link/tl-wa7510n?s[]=wa7510n

[juhosg:
  - cleanup commit message
  - move non kernel related stuff into separate changes
  - rename and refresh 615-MIPS-ath79-TL-WA7510N-v1-support patch
  - merge WA7510N support into the mach-tl-wa901nd.c file
  - add 3.6 support]

Signed-off-by: Stefan Helmert <helst_listen@aol.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34187
2012-11-13 14:48:00 +00:00
Gabor Juhos f2528b1792 ar71xx: use gpio_request_one instead of ath79_set_usb_power_gpio
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34087
2012-11-05 13:23:27 +00:00
Gabor Juhos ed35253f4c ar71xx: don't use the unknown LED on the ZCN-1523-5 board
According to #12421, GPIO 1 controls the power
output on the unused lines of the LAN2 port.
Remove the LED definition in order to prevent
possible permanent hardware damage.

If someone needs that, the power-out feature can
be controlled via the GPIO sysfs interface.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34076
2012-11-04 22:08:54 +00:00
Gabor Juhos 7228a91a3b ar71xx: fix link speed between AR7242 and AR8327 on the RB750GL/RB751G boards
The default pll_1000 value had to be changed
in order to make it working.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33993
2012-10-29 17:24:30 +00:00
Gabor Juhos d54c9653e9 ar71xx: add support for the Senao CAP4200AG board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33956
2012-10-27 08:55:38 +00:00
Gabor Juhos f1f388d527 ar71xx: rw2458n - fix flash parts
See #12338. Redwave rw2458 has uboot, not redboot.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33867
2012-10-19 18:32:49 +00:00
Gabor Juhos 31387947c8 ar71xx: use the ath79_set_ar934x_eth_cfg helper in machine setup routines
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33818
2012-10-17 18:27:47 +00:00
Gabor Juhos 5ffc08e3dc ar71xx: add a helper function for setting up ETH_CFG register on AR934x
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33817
2012-10-17 18:27:45 +00:00
Gabor Juhos c5a32cfc92 ar71xx: add support for the OpenMesh OM2P-HS board
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33800
2012-10-17 08:26:01 +00:00
Gabor Juhos 196c6c5b45 ar71xx: add support for the TL-WR841N/ND v8 board
SVN-Revision: 33621
2012-10-04 20:16:03 +00:00
Gabor Juhos 170cd7a19a ar71xx: avoid possible NULL pointer dereference in ath79_init_{,local}_mac
SVN-Revision: 33575
2012-09-27 20:05:42 +00:00
Gabor Juhos e7b1949d87 ar71xx: automatically find WLAN calibration data on TEW-673GRU
SVN-Revision: 33539
2012-09-25 12:57:40 +00:00
Gabor Juhos 8ed8e51e74 ar71xx: automatically find WLAN calibration data on DIR-825-B1
SVN-Revision: 33538
2012-09-25 12:57:38 +00:00
Gabor Juhos e70ad61e44 ar71xx: use different machtype and setup for the TL-MR3040
Should fix #12211. Compile tested only.

SVN-Revision: 33535
2012-09-24 18:45:56 +00:00
Gabor Juhos 5804b9d1b7 ar71xx: register the NAND controller device on the RB2011
SVN-Revision: 33388
2012-09-13 07:26:26 +00:00
Gabor Juhos 4fd67c3cd4 ar71xx: add device registration code for the AR934x NAND flash controller
SVN-Revision: 33387
2012-09-13 07:26:25 +00:00
Gabor Juhos aa2f4d4c8d ar71xx: add initial support for RB2011UAS-2HnD
SVN-Revision: 33349
2012-09-09 14:05:32 +00:00
Gabor Juhos 3686e18727 ar71xx: use routerboot_find_tag to find wlan data offset on RB751
SVN-Revision: 33348
2012-09-09 14:05:30 +00:00
Gabor Juhos ccabe4a1b4 ar71xx: add RouterBoot related helper routines
SVN-Revision: 33347
2012-09-09 14:05:28 +00:00
Gabor Juhos 44bf7c7cc1 ar71xx: define MTD partitions for RB2011
SVN-Revision: 33345
2012-09-09 14:05:24 +00:00
Gabor Juhos 6ae5ec16e0 ar71xx: add preliminary support for Mikrotik RB2011L
This patch adds preliminary support for the Mikrotik RB2011L.
The NAND flash is not yet supported, so only the initramfs
kernel can be used for now.

[juhosg: remove unnecessary PCI/USB related stuff, the board
does not use that, update commit message]

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

SVN-Revision: 33344
2012-09-09 14:05:22 +00:00
Gabor Juhos 94bac7366c ar71xx: use dynamic clock dividers on the 2nd MDIO of AR934x
SVN-Revision: 33343
2012-09-09 14:05:20 +00:00
Gabor Juhos 7592057774 ar71xx: add dynamic MDIO clock calculation
SVN-Revision: 33342
2012-09-09 14:05:17 +00:00
Gabor Juhos 88a5478781 ar71xx: use the RLE library for RB751
SVN-Revision: 33338
2012-09-08 17:51:56 +00:00
Gabor Juhos 11c3392b7f Revert "ar71xx: only allow RGMII mode on the 2nd ethernet MAC of the AR7240"
That was based on assumptions.

SVN-Revision: 33310
2012-08-29 10:37:55 +00:00
Gabor Juhos eb9a97a360 ar71xx: all0315n: fix ethernet according to vendor info
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33309
2012-08-29 10:37:54 +00:00
Gabor Juhos 5fdbb33db4 ar71xx: Buffalo WZR-HP-AG300H LED support
An improved LED support for Buffalo WZR-HP-AG300H.

There will be two new packages to go with this patch
(ar922x-led-fix-hotplug and ar922x-led-fix-init).
These packages essentially perform the same task of
disabling "JTAG over GPIO pins" function which is
currently required for LEDs on AR922x emac GPIO to work,
and are both considered a temporary fix that circumvent
this problem.

[juhosg: add the hotplug script from the proposed
ar922x-led-fix-hotplug package to ar71xx/base-files]

Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>

SVN-Revision: 33294
2012-08-29 10:11:55 +00:00
Gabor Juhos eebdd633e4 ar71xx: add support for the Allnet ALL0315N board
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33281
2012-08-27 14:55:31 +00:00
Gabor Juhos cca873e8e0 ar71xx: only allow RGMII mode on the 2nd ethernet MAC of the AR7240
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33280
2012-08-27 14:55:26 +00:00
Gabor Juhos 8b3d95bba9 ar71xx: add support for the TRENDnet TEW-712BR board
SVN-Revision: 33231
2012-08-22 20:09:13 +00:00
Gabor Juhos 2811d6c183 ar71xx: fix comment style in mach-tl-wr2543n.c
SVN-Revision: 33227
2012-08-22 12:42:59 +00:00
Gabor Juhos 5a694e09c8 ar71xx: add ALL0305 board alias
For the pure convenience of having a correctly named
image and system name in /proc/cpuinfo , until we can
do that by having system names in DTS...

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33224
2012-08-22 12:33:22 +00:00
Gabor Juhos 0517183b9c ar71xx: add support for TP-Link TL-WDR3600
The TL-WDR3600 is identical to the TL-WDR4300 with the exception that is has
only two antennas.

[juhosg: remove the custom machine type, change the board name instead]

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 33219
2012-08-22 09:43:18 +00:00
John Crispin 968ac3fd03 add led defintion for the WR2543 5GHz WLAN LED
Signed-off-by: Andy Leiserson <andy@leiserson.org>

SVN-Revision: 33215
2012-08-22 09:10:24 +00:00
Gabor Juhos 79a8660d67 ar71xx: init switch hw_reset on the TL-WR1043ND board
SVN-Revision: 32944
2012-08-02 09:54:28 +00:00
Gabor Juhos 563400ef10 ar71xx: ew-dorin: added router firmware generation
[juhosg: remove dead code]

Signed-off-by: embedded wireless GmbH <info@embeddedwireless.de>

SVN-Revision: 32934
2012-08-01 12:24:57 +00:00
Gabor Juhos 010aec0619 ar71xx: Buffalo WLAE-AG300N initial support
The patch set for Buffalo WLAE-AG300N initial support.

There is another patch for wireless led support that
is posted separately.

Note on serial console:
This unit has buffalo standard 4 pin console, but the unit may not power
on if some console apparatus is connected. This is probably due to some
electronic interaction between the unit's electronic power switch circuit
and the serial console apparatus. If this happens, it is required to power
on the unit without the console, then quickly (re-)attach it.

[juhosg: fix coding style]

Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>

SVN-Revision: 32931
2012-08-01 12:24:52 +00:00
Gabor Juhos 7c932579fa ar71xx: make 2.4GHz wlan LED work on the WR2543N
Because ath9k does not supports separate LEDs for
different bands yet, the 2.4GHz LED will show the
activity, even if the 5GHz band is selected.

SVN-Revision: 32615
2012-07-05 16:25:26 +00:00
Gabor Juhos 797944d3f1 ar71xx: add support for the OpenMesh OM2P-LC board
Patch-by: Marek Linder <marek@open-mesh.com>

SVN-Revision: 32611
2012-07-05 08:26:53 +00:00
Gabor Juhos d1b237b335 ar71xx: add initial support for the QCA955X SoCs
SVN-Revision: 32606
2012-07-05 08:26:47 +00:00
Gabor Juhos 86013d40d5 ar71xx: remove the built-in MTD map of the ALL0258N
Pass the mtd_layout via the kernel command line instead.
Also increase the kernel partition size to 1024k, so current kernel can fit in.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 32585
2012-07-03 15:24:01 +00:00
Gabor Juhos 8b9931fd27 ar71xx: add support for the TL-WDR4300 board
SVN-Revision: 32459
2012-06-19 11:51:17 +00:00
Gabor Juhos f509a87f2d ar71xx: remove superfluous include of asm/mach-ath79/pci.h
SVN-Revision: 32455
2012-06-19 10:13:43 +00:00
Gabor Juhos 1a1121158f ar71xx: add a common function to configure USB power GPIOs
SVN-Revision: 32454
2012-06-19 10:13:41 +00:00
Felix Fietkau 26cf21df02 ar71xx: add support for the embeddedwireless Dorin board (based on patch by embeddedwireless.de)
SVN-Revision: 32447
2012-06-19 00:22:04 +00:00
Felix Fietkau dddf321b6e ar71xx: swap the PHY address of the ethernet port of TL-MR3040/TL-MR11U similar to TL-MR3020 to fix ethernet link detection
SVN-Revision: 32336
2012-06-13 12:54:22 +00:00
Felix Fietkau 73b8805e78 ar71xx: fix PHY setup on TL-MR3020 (fixes #11572)
SVN-Revision: 32093
2012-06-06 17:24:12 +00:00
Felix Fietkau dc9675282e ar71xx: add a helper function for setting up PHY4 swapping on ar933x
SVN-Revision: 32092
2012-06-06 17:24:09 +00:00
Felix Fietkau 8039a1bbb2 ar71xx: fix MII clock settings for various chips, improves ethernet stability on AR934x
SVN-Revision: 31925
2012-05-27 21:02:41 +00:00
Gabor Juhos 013f434f5b ar71xx: fix WLAN led for RB751U-2HnD and RB751G-2HnD
Patch by Kamil Trzciński <ayufan@osk-net.pl>

SVN-Revision: 31846
2012-05-23 21:05:25 +00:00
Gabor Juhos ab897ab04e ar71xx: add support for the TP-Link TL-WR1041N v2 board
Patch-by: Vince Huang <axishero@foxmail.com>

SVN-Revision: 31608
2012-05-05 17:02:35 +00:00
Gabor Juhos 3e3a4d3d6b ar71xx: allow to disable link polling on unused PHYs
SVN-Revision: 31533
2012-04-29 18:29:24 +00:00
Gabor Juhos 408de85883 ar71xx: use ap91_pci_init for RB751{,G}
SVN-Revision: 31356
2012-04-19 21:31:48 +00:00
Gabor Juhos 0a9832b50d ar71xx: move USB device registration directly into rb751{,g}_setup
SVN-Revision: 31355
2012-04-19 21:31:43 +00:00
Gabor Juhos 78967e6640 ar71xx: add ap9x_pci_get_wmac_data helper
SVN-Revision: 31354
2012-04-19 21:31:42 +00:00
Gabor Juhos 5c9ca38e47 ar71xx: add sanity checks to decode_rle
Also use -EINVAL instead of -1.

SVN-Revision: 31353
2012-04-19 21:31:40 +00:00
Gabor Juhos e295a077ce ar71xx: initial support for Mikrotik RB751G-2HnD and RB751U-2HnD
Great collaboration on these two fantastic routers on the openwrt forum:
https://forum.openwrt.org/viewtopic.php?id=32320
Above all kudos to aryufan. Well done and thank you everyone else who
contributed.

To-Do: LED for wlan is not yet activated
To-Do: TxPower over 20dBm (RB751U) or 22dBm (RB751G) are not accepted by
the router

Signed-off-by: Hanno Schupp <hanno.schupp@gmail.com>
[juhosg: fix line wrapped patch, fix checkpatch errors, add missing
kernel patches]

SVN-Revision: 31208
2012-04-06 06:45:07 +00:00
Gabor Juhos b77217d963 ar71xx: boost SPI flash read performance
mtd_speedtest results:
                           page read speed
                    old         new        delta
DB120            929 KiB/s   2597 KiB/s   +179.55%
TL-WR1043ND v1   754 KiB/s   2166 KiB/s   +187.27%
TL-WR703N v1     745 KiB/s   2176 KiB/s   +192.08%
TL-MR3220 v1     752 KiB/s   2154 KiB/s   +186.44%
TL-WR2543ND v1   564 KiB/s   2130 KiB/s   +277.66%
TL-WR741ND v2    525 KiB/s   1767 KiB/s   +236.57%
ALFA-AP96        702 KiB/s   1977 KiB/s   +181.62%
WNDR3700         697 KiB/s   1965 KiB/s   +181.92%

SVN-Revision: 31118
2012-03-27 19:38:17 +00:00
Gabor Juhos 6cd5fb7001 ar71xx: remove the built-in MTD map of the AP96 board
Pass the mtd_layout via the kernel command line instead.

SVN-Revision: 31112
2012-03-27 19:38:07 +00:00
Gabor Juhos 61ee283899 ar71xx: remove the built-in MTD map of the PB92 board
Pass the mtd_layout via the kernel command line instead

SVN-Revision: 31111
2012-03-27 19:38:05 +00:00
Gabor Juhos 1094dc1996 ar71xx: remove the built-in MTD map of the Zcomax devices
Pass the mtd_layout via the kernel command line instead.

SVN-Revision: 31110
2012-03-27 19:38:04 +00:00
Gabor Juhos 87e4ec687b ar71xx: remove the built-in MTD maps of several boards
We are passing the MTD layout via the kernel command line, so
it makes no sense to duplicate it in mach-* files. The patch
removes the built-in MTD maps of the following boards:

 * AP113
 * ALFA N2/N5
 * DIR-600
 * DIR-615
 * DIR-825
 * TEW-6{3,5}2BRP
 * TEW-673GRU
 * WHR-G301N
 * WHR-HP-GN
 * WHR-HP-G300N

SVN-Revision: 31108
2012-03-27 19:38:01 +00:00
Gabor Juhos f4d1e3d147 ar71xx: fix button polarity on TL-WR703N and TL-WR741N v4
SVN-Revision: 31102
2012-03-27 19:37:51 +00:00
Gabor Juhos 8a2e4b49de ar71xx: add initial support for RB750GL
SVN-Revision: 31025
2012-03-19 15:57:04 +00:00
Gabor Juhos d19f3dd512 ar71xx: make rb750_latch_change 'static void'
SVN-Revision: 31024
2012-03-19 15:57:03 +00:00
Gabor Juhos 5348f46c80 ar71xx: add latch_change field to rb750_led_platform_data
SVN-Revision: 31023
2012-03-19 15:57:01 +00:00
Gabor Juhos 8a471efe01 ar71xx: add platform data for the RB750 NAND driver
SVN-Revision: 31022
2012-03-19 15:56:59 +00:00
Gabor Juhos e9b45ebaba ar71xx: add AR934x specific interface speed setup for ge0
SVN-Revision: 31017
2012-03-19 11:11:20 +00:00
Gabor Juhos 6036151187 ar71xx: add support for the jjPlus JA76PF2 board
SVN-Revision: 30957
2012-03-16 18:00:34 +00:00
Gabor Juhos a680662391 ar71xx: change LED name prefix on the jjplus boards
SVN-Revision: 30956
2012-03-16 18:00:26 +00:00
Gabor Juhos 1c5ac02a29 ar71xx: reset the switch on AR934x before ethernet device registration
SVN-Revision: 30922
2012-03-13 17:29:33 +00:00
Gabor Juhos 66df117d1b ar71xx: use a dummy callback for interfaces with fixed speed
SVN-Revision: 30913
2012-03-12 20:38:58 +00:00
Gabor Juhos 8b2b37ae58 ar71xx: merge ar934x_bo_ddr_flush patch
SVN-Revision: 30912
2012-03-12 20:38:57 +00:00
Gabor Juhos 2d89fa7f43 ar71xx: fix WPS button polarity on TL-WR2543N
SVN-Revision: 30849
2012-03-07 19:50:53 +00:00
Gabor Juhos d72bde99cd ar71xx: merge files-3.2 to files
SVN-Revision: 30405
2012-02-10 08:19:31 +00:00
Gabor Juhos 386cbfe45b ar71xx: move arch specific files to files-2.6.39
SVN-Revision: 29867
2012-01-22 22:38:11 +00:00
Gabor Juhos ef1c53b7b7 ar71xx: change board id of the UniFi board
SVN-Revision: 29849
2012-01-22 13:51:50 +00:00
Gabor Juhos fbf81c8e79 ar71xx: move irq_to_gpio and gpio_to_irq into gpio.c
SVN-Revision: 29713
2012-01-11 18:00:50 +00:00
Gabor Juhos a1dcbc66a6 ar71xx: add initial support for the TL-WR2543N/ND board
The WLAN LEDs are not working yet.

SVN-Revision: 29680
2012-01-07 19:36:35 +00:00
Gabor Juhos 67b2814842 ar71xx: local mac support on the wndr3700
The wndr3700 at least has no eth0 mac address and usually leverages
the first wireless device's mac when in a bridged scenario. If,
however, you want to route, and not bridge the interfaces, you
need a unique mac address for it.

This patch sets the local bit on the mac address pulled from the
wireless chip and uses the resulting address for eth0.

Patch-by: Dave Taht <dave.taht@gmail.com>

SVN-Revision: 29675
2012-01-07 17:24:44 +00:00
Gabor Juhos 1e848b17ad ar71xx: add support for Redwave RW2458N
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 29669
2012-01-06 07:20:59 +00:00
Gabor Juhos b8f0d86115 ar71xx: add inital support for the ALFA Network AP96 board
The microSD slot and the Real Time Clock is not working yet.
The miniPCIe interface is not tested due to the lack of a
suitable card.

SVN-Revision: 29662
2012-01-04 21:13:54 +00:00
Gabor Juhos 923f3e3752 ar71xx: allow to use the command line hack on compex devices
SVN-Revision: 29659
2012-01-04 17:30:58 +00:00
Gabor Juhos 2f53f82203 ar71xx: use the TL-MR3x20 code for the TL-WR841N/ND v7
These models are based on the AP99 reference board,
and uses the AR7241 SoC.

SVN-Revision: 29658
2012-01-04 17:30:57 +00:00
Gabor Juhos 90bfef9ec9 ar71xx: allow to use LAN LED on the TL-WA901N/ND boards
SVN-Revision: 29653
2012-01-04 17:30:50 +00:00
Gabor Juhos 1045c83527 ar71xx: add support for TP-Link TL-MR3020
This patch adds support for the TP-Link device TL-MR3020 which is very
similiar to the TL-WR703N.
The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions.
Only four LEDs can be controlled via GPIO. The power LED is connected to
the power supply.
The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals
of the sliding switch have been mapped to BTN_0 and BTN_1.

I have also setup a wiki page with details here:
http://wiki.openwrt.org/toh/tp-link/tl-mr3020

USB is working and has been tested with USB mass storage and USB UMTS
stick.

Wifi also seems to work.

Ethernet is working too.

Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>

SVN-Revision: 29651
2012-01-04 17:30:47 +00:00
Gabor Juhos 1e68f10b87 ar71xx: add support for the ALFA Network N2/N5 boards
SVN-Revision: 29635
2012-01-01 19:30:25 +00:00
Gabor Juhos 5c067db8a7 ar71xx: define LAN/WAN LEDs for the TL-WR741N/ND boards
SVN-Revision: 29631
2011-12-31 15:02:46 +00:00
Gabor Juhos 557009bbdb ar71xx: fix LEDs on the WRT400N
SVN-Revision: 29624
2011-12-31 13:54:11 +00:00
Jo-Philipp Wich ebefe1eb3a the mach file of the WZR-HP-G300NH2 accidentally claimed the mach id of the WZR-HP-AG300H, correct the id (#10649)
SVN-Revision: 29593
2011-12-21 01:27:48 +00:00
Felix Fietkau 11013ad947 ar71xx: add missing wireless led changes for wzr-hp-g300nh2
SVN-Revision: 29568
2011-12-19 09:04:15 +00:00
Felix Fietkau 0cc056cb7e ar71xx: add support for the wzr-hp-g300nh2
Signed-off-by: Mark Deneen <mdeneen@gmail.com>

SVN-Revision: 29567
2011-12-18 22:20:17 +00:00
Gabor Juhos 67c7980290 ar71xx: connect GMAC0 to the internal switch on DB120
Because the external switch has no driver yet, connect GMAC0
to the PHY4 of the internal switch for now. This allows to
use the DB120 board as a router with 4LAN+1WAN ports.

SVN-Revision: 29557
2011-12-15 22:25:38 +00:00
Gabor Juhos 5bbd416e38 ar71xx: add defines for the AR934X GMAC interface
SVN-Revision: 29556
2011-12-15 22:25:36 +00:00
Gabor Juhos e47a8c2bb2 ar71xx: fix GMAC1 interface speed on the DB120 board
SVN-Revision: 29555
2011-12-15 22:25:35 +00:00
Gabor Juhos 00667c3846 ar71xx: ag71xx: allow to connect PHY4 to the CPU on AR934X
SVN-Revision: 29553
2011-12-15 22:25:30 +00:00
Gabor Juhos e2a546d475 ar71xx: allow to attach the internal switch for AR934x
SVN-Revision: 29550
2011-12-15 22:25:22 +00:00
Gabor Juhos 9ae65588d8 ar71xx: introduce ar71xx_switch_data
SVN-Revision: 29549
2011-12-15 22:25:11 +00:00
Gabor Juhos d1f7783612 ar71xx: fix mac addresses on jjPlus devices
SVN-Revision: 29538
2011-12-15 13:25:18 +00:00
Gabor Juhos b9c5cb5c9a ar71xx: add support for ALFA Network's Hornet-UB board
SVN-Revision: 29535
2011-12-14 20:54:10 +00:00
Gabor Juhos 66c8cc0f6d ar71xx: add GPIO function bit defines for AR933X
SVN-Revision: 29534
2011-12-14 20:54:07 +00:00
Felix Fietkau 7076d74b21 ar71xx: fix gpio count for ar7241/ar7242
SVN-Revision: 29532
2011-12-14 20:47:24 +00:00
Felix Fietkau b878f4a927 ar71xx: register extra leds behind the wireless mac on wzr-hp-g450h
SVN-Revision: 29531
2011-12-14 20:21:42 +00:00
Felix Fietkau 3806671fe5 ar71xx: fix wireless led on wzr-hp-g450h
SVN-Revision: 29515
2011-12-13 15:00:43 +00:00
Gabor Juhos 2dd7dfb1c9 ar71xx: enable AR9341 support at setup.c
Patch-by: dyq <729650915@qq.com>

SVN-Revision: 29514
2011-12-13 14:59:43 +00:00
Gabor Juhos 058998acdb ar71xx: Build images for Netgear WNDRMAC and WNDRMACv2
The WNDRMAC is a WNDR3700v2 (64MB RAM, 16MB flash) in a white case. The
WNDRMACv2 is a WNDR3800 (128MB RAM, 16MB flash) in a WNDRMAC case.

The WNDRMAC case doesn't have "holes" or labels for the 2.4GHz LED or
switch ports 2-4. The stock firmware uses a single LED (in the 5GHz
position) to indicate the status of both radios, and a single LED (in the
switch port 1 position) to indicate the status of all LAN ports. The
"missing" LEDs are present on the board, and easily shine through the
case. Unlike the stock firmware, OpenWrt will use these "hidden" LEDs.

I've tested the WNDRMACv2 image. I don't have a v1 WNDRMAC, but assume
that this is sufficient to build a fully-functional image.

Signed-off-by: Mark Mentovai <mark@moxienet.com>

SVN-Revision: 29513
2011-12-13 14:59:40 +00:00
Felix Fietkau 48f9717371 ar71xx: add gpios and usb for wzr-hp-g450h
SVN-Revision: 29509
2011-12-13 13:33:44 +00:00
Gabor Juhos 4ca2d86493 ar71xx: use RedBoot parser on PB44
SVN-Revision: 29501
2011-12-11 15:52:47 +00:00
Gabor Juhos bdc2eca7de ar71xx: use correct mac on the lan interface on several TP-LINK devices
SVN-Revision: 29458
2011-12-05 21:10:58 +00:00
Gabor Juhos 0103069372 ar71xx: allow to pass negative offset values for ar71xx_init_mac
SVN-Revision: 29457
2011-12-05 21:10:55 +00:00
Gabor Juhos ada92aee62 ar71xx: don't register PCI controller on AR934x if PCIE_RC bit is not set
SVN-Revision: 29456
2011-12-05 18:21:15 +00:00
Felix Fietkau 1f809532de ar71xx: add preliminary support for wzr-hp-g450h
SVN-Revision: 29441
2011-12-05 14:20:51 +00:00
Felix Fietkau d1f63f8538 ar71xx: move multi-m25p80 concat code from wzr-hp-ag300h mach code to dev-m25p80.c, other buffalo routers use it as well
SVN-Revision: 29440
2011-12-05 14:20:44 +00:00
Gabor Juhos 4cc2b9bb06 ar71xx: rewrite WNDR3700/3800 handling
SVN-Revision: 29434
2011-12-05 13:03:54 +00:00
Gabor Juhos 7cfa39f032 ar71xx: use the tp-link parser on the tp-link boards
Also remove static partition maps.

SVN-Revision: 29416
2011-12-03 18:13:31 +00:00
Gabor Juhos fc7fb29bae ar71xx: run the RedBoot parser only on the RedBoot based boards
SVN-Revision: 29414
2011-12-03 18:13:25 +00:00
Gabor Juhos 9cc28d5aa0 ar71xx: run the MyLoader parser only on the WP543 board
SVN-Revision: 29413
2011-12-03 18:13:23 +00:00
Gabor Juhos 67a0b9aada ar71xx: run the wrt160nl parser only on the WRT160NL board
Also remove static mtd partition definitions.

SVN-Revision: 29412
2011-12-03 18:13:20 +00:00
Gabor Juhos f188f1bad5 ar71xx: add support for Ubiquiti AirRouter
Signed-off-by: Gergely Barta <gergely.barta@printerfairkft.hu>

SVN-Revision: 29395
2011-12-01 22:49:02 +00:00
Gabor Juhos f20797306a ar71xx: modify phy mask of the WP543 board
This fixes ethernet on newer boards. Based on a patch from #9702.

SVN-Revision: 29328
2011-11-24 20:09:43 +00:00
Gabor Juhos c20d7378e5 ar71xx: fix wndr3800 machine name
This fixes the machine name in /proc/cpuinfo and luci status page machine name.

Signed-off-by: Petri Rosenström <petri.rosenstrom@gmail.com>

SVN-Revision: 29326
2011-11-24 20:09:38 +00:00
Gabor Juhos 9990523a0f ar71xx: set GE0 phy_mask for AR933x
SVN-Revision: 29274
2011-11-20 11:30:10 +00:00
Gabor Juhos f27548448b ar71xx: fix USB LED on the DB120 board
SVN-Revision: 29126
2011-11-14 17:43:15 +00:00
Gabor Juhos 6ebbb1329d ar71xx: add a function for selecting output signal on a given GPIO pin
SVN-Revision: 29125
2011-11-14 17:43:14 +00:00
Gabor Juhos 0c1d3617d7 ar71xx: fix GPIO function handling on AR934x
SVN-Revision: 29124
2011-11-14 17:43:13 +00:00
Gabor Juhos aa0c8c4885 ar71xx: add AR71XX_ prefix to GPIO_REG_* defines
SVN-Revision: 29123
2011-11-14 17:43:11 +00:00
Gabor Juhos 12dae96097 ar71xx: fix a compiler warning
SVN-Revision: 29110
2011-11-14 13:07:47 +00:00
Gabor Juhos 5ae0fd802c ar71xx: fix GPIO count for AR934x
SVN-Revision: 29109
2011-11-14 13:07:45 +00:00
Gabor Juhos e52269364a ar71xx: flush DDR writeback buffers for WMAC and PCIe on AR934X
SVN-Revision: 29108
2011-11-14 11:49:53 +00:00
Gabor Juhos 3104d70552 ar71xx: use a dummy irq chip for WMAC and PCIe irq hadling
SVN-Revision: 29107
2011-11-14 11:49:51 +00:00
Gabor Juhos 42e8ae09b5 ar71xx: add AR934X_RESET_REG_PCIE_WMAC_INT_STATUS defines
SVN-Revision: 29106
2011-11-14 11:49:49 +00:00
Gabor Juhos c15caea360 ar71xx: add an irq parameter for ar724x_pcibios_init
SVN-Revision: 29105
2011-11-14 11:49:47 +00:00
Gabor Juhos cf90b24bb9 ar71xx: remove hardwired interface parameters from mach-* files
SVN-Revision: 29103
2011-11-14 07:38:09 +00:00
Gabor Juhos defc79cb40 ar71xx: force hardwired interface parameters in ar71xx_add_device_eth
SVN-Revision: 29102
2011-11-14 07:38:07 +00:00
Gabor Juhos 6f4bc1ce37 ar71xx: use if-else instead of conditional operators in ar71xx_add_device_eth
SVN-Revision: 29101
2011-11-14 07:38:05 +00:00
Gabor Juhos 368bbc510b ar71xx: enable has_gbit flag on AR724{0,1}
SVN-Revision: 29026
2011-11-13 17:36:36 +00:00
Gabor Juhos 15d7016c9f ar71xx: fixup onboard PCIe chip registration on the DB120 board
SVN-Revision: 29022
2011-11-13 12:48:03 +00:00
Gabor Juhos f623066e60 ar71xx: drop DB120_WMAC_MAC_OFFSET, it is not needed
SVN-Revision: 29021
2011-11-13 12:48:01 +00:00
Gabor Juhos d0db89133c ar71xx: remove mii_ctrl resources of the ethernet devices
SVN-Revision: 29016
2011-11-13 11:27:03 +00:00
Gabor Juhos 538a9493b9 ar71xx: set MII interface speed from the set_speed callbacks
SVN-Revision: 29013
2011-11-13 11:26:59 +00:00
Gabor Juhos 93cd46be13 ar71xx: rename set_pll callback to set_speed in ag71xx_platform_data
Also rename the corresponding callback functions.

SVN-Revision: 29012
2011-11-13 11:26:57 +00:00
Gabor Juhos 9579bb4267 ar71xx: ag71xx: remove MII interface setup code
SVN-Revision: 29011
2011-11-13 11:26:56 +00:00
Gabor Juhos da64ce8603 ar71xx: configure MII interface type from ar71xx_setup_phy_if_mode
SVN-Revision: 29010
2011-11-13 11:26:54 +00:00
Gabor Juhos 5ad763075e ar71xx: use the button for WPS control on the DB120
SVN-Revision: 28990
2011-11-12 12:50:20 +00:00
Gabor Juhos 4555be2bec ar71xx: register the second ethernet interface on the DB120 board
SVN-Revision: 28989
2011-11-12 12:50:19 +00:00
Gabor Juhos 368c6605a0 ar71xx: implement SoC specific phy interface setup
SVN-Revision: 28988
2011-11-12 12:50:18 +00:00
Gabor Juhos 21d317b9cc ar71xx: move phy interface setup into a separate function
SVN-Revision: 28987
2011-11-12 12:50:16 +00:00
Gabor Juhos aff0c84ffa ar71xx: register both MDIO bus on the DB120 board
SVN-Revision: 28986
2011-11-12 12:09:59 +00:00
Gabor Juhos b144249108 ar71xx: add AR934X specific MDIO registration code
SVN-Revision: 28985
2011-11-12 12:09:56 +00:00
Gabor Juhos f835106c8c ar71xx: add a secondary mdio bus
SVN-Revision: 28984
2011-11-12 12:09:54 +00:00
Gabor Juhos 90a42da270 ar71xx: rename ar71xx_mdio_* structures to ar71xx_mdio0_*
SVN-Revision: 28983
2011-11-12 12:09:50 +00:00
Gabor Juhos 9daa2149fd ar71xx: add an id argument to ar71xx_add_device_mdio
SVN-Revision: 28982
2011-11-12 12:09:48 +00:00
Gabor Juhos b07b687aec ar71xx: pass netdev and miidev pointer to ar71xx_add_device_dsa
SVN-Revision: 28981
2011-11-12 12:09:42 +00:00
Gabor Juhos a9216bb76e ar71xx: add AR934x specific USB setup
SVN-Revision: 28980
2011-11-12 10:54:20 +00:00