Commit Graph

41376 Commits (0e9e8d832321ba7b99f9f7b6152245c542153cbd)

Author SHA1 Message Date
Mathias Kresin 0e9e8d8323 kernel: dwc2: add support for host mode external vbus supply
Backport patch adding support for the vbus-supply devicetree property,
which allows to specific GPIOs (via fixed regulators) to enable
vbus/usb power.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin 0b62fe5ed8 lantiq: complete AVM FRITZ!Box 3370 support
Rename the image and use a compatible string which indicates that only
hardware revision 2 and higher is supported.

It allows to use the wireless LED, as HWRev 1 uses GPIO#39 for the
wireless LED and starting with HWRev 2 GPIO#35 is used for the wireless
LED and GPIO#39 for IFX_GPIO_MODULE_EXTPHY_MDIO.

The HWREV can be checked by connecting to the fritzbox right after power
on via ftp:

  ftp> quote GETENV HWSubRevision

Within the same HW revision 5 of the Fritz!Box 3370 different NAND flash
chips are used. Usually it isn't a big deal but depending on the used
NAND flash chip, the ECC calculation is done different (and incompatible
of course).

Boards with a Micron MT29F1G08ABADA NAND flash chip are using the NAND
chip to calculate the ECC (on-die). Boards with a Hynix HY27UF081G2M NAND
flash chip are doing the ECC calculation in software.

Supporting both with a single DTS isn't possible. It might be possible
to add a patch selecting the ECC mode dynamicaly based on the found NAND
flash chip. But such a patch has no chance to get accepted upstream and
most likely need to be touched with every kernel update.

Instead two images are created. One for Micron NAND flash chip and one
for Hynix NAND flash chip. So far no pattern is known to identify the
used flash chip without opening the box.

Add the power off GPIO. At least EVA version 2186 sets/keeps the GPIO as
input, which will cause a reboot 30sec after power on. For boards with
EVA version 2186 the installation is tricky as it has to be finished
within the 30sec time frame.

The EVA version can be checked by connecting to the fritzbox right after
power on via ftp:

  ftp> quote GETENV urlader-version

The ath9k eeprom/caldata is at a different and offset and stored in
reverse order (from the last byte to the beginning) on the flash.
Reverse the bits to bring the data into the format expected by the
ath9k driver.

Since the ath9k eeprom is stored in reverse order on flash, we can not
use the mac address from the on flash eeprom. Get the MAC address from
the tffs instead.

Within the same HW revision 5 of the Fritz!Box 3370 both version of the
vr9 SoC are used. During preparation of kernel 4.14 support, all
devicetree source files were changed to load the vr9 v1.1 and vr9 v1.2
gphy firmware, which fixed the embedded phys for boards using the
version 1.2 of the vr9 SoC.

While at it, add a trigger to make use of the LAN LED. Setup the
build-in switch and add a hint for LuCI two show the ports in order
matching the labels on the case

Add support for the second USB port and provide the volatage GPIOs. Use
GPIO#21 as PCIe reset pin. The lan led is connected to GPIO#38.

Name the rootfs partition ubi and remove the mtd/rootfs related kernel
bootargs to use the OpenWrt autoprobing based on the partition name.

Enable sysupgrade support to allow an upgrade from a running system.
Since sysupgrade wasn't supported till now, drop image build code which
was added to allow a sysupgrade from earlier OpenWrt versions.

Build images that allow an (initial) installation via EVA bootloader.

To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote SETENV linux_fs_start 0
  ftp> quote MEDIA FLSH
  ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-kernel.bin mtd1
  ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-filesystem.bin mtd0

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin d7b7483343 lantiq: switch to kernel 4.14
Use kernel 4.14 by default.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin 0678cc850c ltq-xdsl-app: start after led script
During handshake we are highjack and reset a LED to the configured trigger
afterwards. ltq-xdsl-app need to start after the LED init script, to
ensure that the LED init script doesn't re-highjack the LED we are
currently using for handshake indication.

Drop the comment about the atm dependency. The dependency was fixed quite
some time ago by using hotplug scripts for br2684ctl.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Hans Dedecker 0ed9281fda curl: bump to 7.60.0
Refresh patches; remove 320-mbedtls_dont_use_deprecated_sha256_function
patch as upstream fixed

For changes in version 2.60 see https://curl.haxx.se/changes.html#7_60_0

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-05-16 14:36:22 +02:00
Kevin Darbyshire-Bryant afbb3d20f2 kmod-sched-cake: bump to latest 20180515
Following changes as part of the kernel
upstreaming attempts.  And fix a slight fsck up
when calculating overheads for GSO packets.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-05-16 08:40:55 +02:00
Hans Dedecker ac70ac3532 ebtables: update to latest git 2018-05-15
66a9701 ebtables: Fix build errors and warnings
9fff3d5 include: Fix musl libc compatibility
b1cdae8 extensions: Add string filter to ebtables

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-05-15 14:31:11 +02:00
Felix Fietkau 14ff1278ee mt76: update to the latest version
b2ecc52 mt76x2: fix avg_rssi estimation
fd58b28 mt76x2: add a polling delay in mt76x2_mac_stop routine
a78673d mt76: fix sending encrypted broadcast packets for secondary interfaces
e87f925 mt76x2: apply coverage class on slot time too

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-15 13:19:45 +02:00
John Crispin 7e15e21766 Revert "ramips: mmc: Sync with staging drivers"
This reverts commit 2d401925b9.

Signed-off-by: John Crispin <john@phrozen.org>
2018-05-15 12:42:40 +02:00
Wei Yongjun 87c254c87e staging: mt7621-eth: fix return value check in mt7621_gsw_probe()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: f079b6406348 ("staging: mt7621-eth: add gigabit switch driver (GSW)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-15 06:46:08 +02:00
Wei Yongjun edec251870 staging: mt7621-eth: fix return value check in mtk_connect_phy_node()
In case of error, the function of_phy_connect() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.

Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-15 06:45:53 +02:00
Wei Yongjun c4ae54dfab staging: mt7621-eth: fix return value check in mtk_probe()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-15 06:45:34 +02:00
Rosen Penev e07baec9fa ramips: pci: sync with staging driver
This is an amagalmation of two upstream commits dealing with whitespace
and dead code removal. I'm synching instead of having two separate commits
as they go out of order compared to previous commits here.

Tested on GnuBee PC1.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-15 06:45:07 +02:00
Rosen Penev 2d401925b9 ramips: mmc: Sync with staging drivers
Mostly whitespace cleanups. Some unneeded code was removed.

MMC init was also moved to the probe function as in
6069bdd087

The cleanup commits are over 100, making it hard to do them individually.

Tested on GnuBee PC1 with an SD card being used as swap.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-15 06:44:48 +02:00
Toke Høiland-Jørgensen 50913b77e4 wireguard: Add support for ip6prefix config option
This makes it easier to distribute prefixes over a wireguard tunnel
interface, by simply setting the ip6prefix option in uci (just like with
other protocols).

Obviously, routing etc needs to be setup properly for things to work; this
just adds the config option so the prefix can be assigned to other
interfaces.

Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
2018-05-15 06:41:38 +02:00
David Woodhouse 4424a9ff20 linux-firmware: Add firmware for usb-serial-ti-usb
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2018-05-15 06:39:46 +02:00
Matthias Badaire a0685deec4 ramips: Add i2c support for mt7620n
I2c is supported on mt7620n like on mt7620a when checking the datasheet

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-15 06:39:46 +02:00
Alberto Bursi e09d4c850d kirkwood: support for buttons in Audi and Viper
Both these devices have a wps and a reset button on
GPIO pins, which need kmod-gpio-button-hotplug
package to work.

Add this package to their default package config.

Troubleshooted and tested on a Viper.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-05-15 06:39:37 +02:00
Johann Neuhauser c15dfbeea0 ath79: fix gmac compatible in ar9330.dtsi and ag71xx_setup_gmac_933x
1. compatible property in node gmac was wrong

2. ag71xx_setup_gmac_933x should use np of gmac-config and
   not the pointer to gmac. gmac is only used for the reg address.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-05-15 06:38:07 +02:00
Daniel Golle 96f4792fdb mac80211: refactor non-{sae,dfs} mesh initialization
Refactor mesh initialization into a separate function, do some cleaning
on the way to make the code more readable.
Changes:
 * Move iw mesh setup to new mac80211_setup_mesh()
 * fallback on 'ssid' parameter in case 'mesh_id' isn't set
 * move setting of freq variable to shared code as it is needed for
   both, the wpa_supplicant and the iw based setup.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-05-15 02:05:56 +02:00
Sven Eckelmann ba5ec6b77c hostapd: fix VHT80 for encrypted mesh channel settings
The max_oper_chwidth settings was parsed incorrectly for big endian system.
This prevented the system to switch to VHT80 (or VHT160). Instead they were
mapped to:

* HT20:   20MHz
* VHT20:  20MHz
* HT40:   40MHz
* VHT40:  40MHz
* VHT80:  40MHz
* VHT160: 40MHz

This happened because each max_oper_chwidth setting in the config file was
parsed as "0" instead of the actual value.

Fixes: a4322eba2b ("hostapd: fix encrypted mesh channel settings")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-05-14 19:07:37 +02:00
Sven Eckelmann 547042398a mac80211: Re-enable encrypted 11s meshpoint
The commit 574e4377fa ("mac80211: properly setup mesh interface") uses
the variable $wpa to decide whether encrypted meshpoint is requested by the
user or not. But the variable $wpa will only be set correctly after the
function wireless_vif_parse_encryption is called.

Fixes: 574e4377fa ("mac80211: properly setup mesh interface")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-05-14 18:37:44 +02:00
Michael Gray bfbdeeb3de mvebu: add support for WRT32X (venom)
Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM
with a different flash layout and boots zImage rather than uImage.

Specification:
- Marvell Armada 385 88F6820 (2x 1.8GHz)
- 256MB of Flash
- 512MB of RAM
- 2.4GHz (bgn) and 5GHz (an+ac wave 2)
- 4x 1Gbps LAN + 1x 1Gbps WAN
- 1x USB 3.0 and 1x USB 2.0/eSATA (combo port)

Flash instruction:
Apply factory image via web-gui.

Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-05-14 17:20:10 +02:00
John Crispin e1a9485b0e firewall3: update to latest git HEAD
b45e162 helpers: fix the set_helper in the rule structure
f742ba7 helpers.conf: support also tcp in the CT sip helper
08b2c61 helpers: make the proto field as a list rather than one option

Signed-off-by: John Crispin <john@phrozen.org>
2018-05-14 16:24:10 +02:00
Linus Walleij 1f56417e6b gemini: Augment DIR-685 device tree for RTL8366RB
This makes the ethernet and RTL8366RB come up on the
D-Link DIR-685.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-14 16:24:10 +02:00
Linus Walleij 3b48111df9 gemini: create zImage for DIR-685
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-14 16:24:09 +02:00
NeilBrown edea934799 ramips: remove unnecessary resource details.
These resources are extracted from devicetree, so they aren't
needed here.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:24:07 +02:00
NeilBrown 1f78625714 ramips: remove conditional compilation.
Code currently defines:

and then compiles code only if they are defined.
We might want to disable some of these via devicetree one
day, but for now just remove the #defines and the
conditions - all the code for different ports is
easy to identify.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:24:04 +02:00
NeilBrown 5f7396ebef ramips: improve interrupt mapping
As the Interrupts for the PCI adapters are listed in
devicetree we shouldn't need to have them explicit in the code.

The simplest way to do this is to use of_irq_parse_and_map_pci()
and specify an interrupt-map which identifies the different
PCI hosts by bus/slot numbers.
This has the advantage that the hwirq number are mapped to virq
numbers for us, so the ugly hack can go.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:23:59 +02:00
Christian Lütke-Stetzkamp 2ad4daf579 ramips: Remove redundant owner assignment
Remove the owner assignment form the platform driver as
platform_driver_register() already initializes the owner.
Found using coccinelle.

Signed-off-by: Christian Lütke-Stetzkamp <christian@lkamp.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:23:36 +02:00
Rosen Penev a098a78a33 ramips: Move PCI driver to files directory
This will make it easier to port upstream code.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-14 15:55:17 +02:00
Daniel Golle 574e4377fa mac80211: properly setup mesh interface
Setup wpa_supplicant for encrypted mesh or when using DFS channels and
adjust interface setup to pass fixed frequency for mesh mode.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-05-14 09:48:58 +02:00
Daniel Golle 6e0fa4a76d hostapd: fix mesh+AP
Fix encrypted (or DFS) AP+MESH interface combination in a way similar
to how it's done for AP+STA and fix netifd shell script.
Refresh patches while at it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-05-14 09:48:58 +02:00
Jo-Philipp Wich 6aaeec666d rpcd: update to lastest HEAD
8206219 uci: fix memory leak in rpc_uci_replace_savedir()
10f7878 exec: close stdout and stderr streams on child signal
92d0d75 uci: use correct sort index when reordering sections

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-14 07:16:47 +02:00
Kevin Darbyshire-Bryant 89c5e32c3e wireguard: bump to 0.0.20180513
6b4a340 version: bump snapshot
faa2103 compat: don't clear header bits on RHEL
4014532 compat: handle RHEL 7.5's recent backports
66589bc queueing: preserve pfmemalloc header bit
37f114a chacha20poly1305: make gcc 8.1 happy
926caae socket: use skb_put_data
724d979 wg-quick: preliminary support for go implementation
c454c26 allowedips: simplify arithmetic
71d44be allowedips: produce better assembly with unsigned arithmetic
5e3532e allowedips: use native endian on lookup
856f105 allowedips: add selftest for allowedips_walk_by_peer
41df6d2 embeddable-wg-library: zero attribute padding
9a1bea6 keygen-html: add zip file example
f182b1a qemu: retry on 404 in wget for kernel.org race

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-05-14 10:41:21 +08:00
Jo-Philipp Wich aadca035bc at91: sama5d4: fix bad mkubifs options
Drop the "-x lzo" compression type override from MKUBIFS_OPTS since we
do not support it in mkfs.ubifs. Attempting to use LZO compression results
in "Error: bad compressor name".

The build system also appends an explicit "--compr=zlib" to the mkfs command
line, turning the "-x" flag into a no-op anyway.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-13 18:33:47 +02:00
Jo-Philipp Wich 56bd23cf52 kernel: let kmod-rtl8366-smi conditionally depend on kmod-of-mdio
We cannot depend on CONFIG_OF in the module definition context as this symbol
is not defined for OpenWrt menuconfig. Depend on the targets that appear to
need the kmod-of-mdio module instead.

The target dependency list may not be complete, it is based on the build
failures encountered by the build bots.

Fixes: dc629d9cf5 ("kernel: fix kmod-switch-rtl8366-smi dependency")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-13 18:24:38 +02:00
Rafał Miłecki 404508001e kernel: use accepted version of bcm47xxpart fix commit
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-12 23:53:44 +02:00
Rafał Miłecki 070693477a kernel: backport mtd patch for minor partitioning cleanup
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-12 23:14:07 +02:00
Felix Fietkau a3096b4b33 kernel: fix build error in flow offload code with CONFIG_NETFILTER=n
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-12 22:28:00 +02:00
Kevin Darbyshire-Bryant 066c85321e dnsmasq: bump to 2.80test2
Refresh patches and backport upstream to current HEAD:

1f1873a Log warning on very large cachesize config, instead of truncating it.
0a496f0 Do unsolicited RAs for interfaces which appear after dnsmasq startup.
e27825b Fix logging in previous.
1f60a18 Retry SERVFAIL DNSSEC queries to a different server, if possible.
a0088e8 Handle query retry on REFUSED or SERVFAIL for DNSSEC-generated queries.
34e26e1 Retry query to other servers on receipt of SERVFAIL rcode.
6b17335 Add packet-dump debugging facility.
07ed585 Add logging for DNS error returns from upstream and local configuration.
0669ee7 Fix DHCP broken-ness when --no-ping AND --dhcp-sequential-ip are set.
f84e674 Be persistent with broken-upstream-DNSSEC warnings.

Compile & run tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-05-12 22:05:07 +02:00
Rafał Miłecki 02225f5763 bcm53xx: backport the first bunch of 4.18 BCM5301X patches
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-12 15:38:55 +02:00
Jo-Philipp Wich cf7a88cf5a at91: cleanup kernel configurations
The subtarget configurations contained a lot of reduntant symbols, arbitrary
overrides and symbols set to =m.

Remove most of these redundant settings to shrink the subtarget configurations
to a manageable size.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 18:24:00 +02:00
Jo-Philipp Wich f23326eb76 at91: sama5d2: remove CONFIG_XZ_DEC override
Fixes the following error spotted by the buildbot:

    Package kmod-fs-squashfs is missing dependencies for the following libraries:
    xz_dec.ko

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 16:40:34 +02:00
Jo-Philipp Wich 0167f53b9d at91: add missing config symbols
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 16:01:26 +02:00
Jo-Philipp Wich d8c7cd9cb1 kernel: rtl8366_smi: guard of_mdiobus_register() call
Make the call to of_mdiobus_register() dependant on CONFIG_OF to avoid
pulling in an unwanted dependency on of_mdio.ko.

Fixes: 3dc523f232 kernel: add OF support to rtl8355 driver
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 15:07:56 +02:00
hux ecd954d530 dnsmasq: add specific interface procd triggers
Right now interface.update events are sent out by netifd upon interface state,
route, address (lifetime), prefix lifetime changes.
Dnsmasq is only interested in interface state changes and currently adds an
interface trigger for all the "interface.*" events.
In combination with commit 23bba9cb33, which triggers a SIGHUP signal to dnsmasq,
IPv6 address/prefix lifetime changes on the wan will trigger dnsmasq reloads which
can become frequent in case of shorter lifetimes.

To avoid frequent dnsmasq reload, this patch adds specific interface triggers.
During dnsmasq init it loops dhcp uci section; if the value of the ignore option
is set to 0, then the corresponding interface trigger is not installed.
Otherwise, if the ignore option value is 1, then procd_add_interface_trigger is
called which adds the interface trigger.

Signed-off-by: hux <xinxing.huchn@gmail.com>
2018-05-11 13:49:03 +02:00
John Crispin dc629d9cf5 kernel: fix kmod-switch-rtl8366-smi dependency
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-10 10:22:19 +02:00
Piotr Dymacz ce4d2fb5cc ar71xx: fix and improve ALFA Network Tube2H support
Fix ART offset (make it universal for 8/16 MB versions of the board) and
while at it, include also GPIO setup for h/w watchdog (EM6324QYSP5B).

Fixes: FS#1532

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-05-09 20:32:47 +02:00
John Crispin a564cfcd83 kernel: fix chipidea2 dependencies
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-09 19:55:10 +02:00