Patch reverts 43332 which seems to cause issues with VLAN functionality.
Add a specific check to check whether ANEG is still enabled and re-enable
it if necessary. Disable generic phy soft reset for kernel >=3.16.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43356
We should make sure that also for ar8216 hw gets initialized.
For ar8216 hw_init is a dummy currently. The hw_init used for ar8236
should be generic enough to be usable with ar8216 too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43334
Move the PHY fixup call to the PHY init loop.
Use ar8xxx_has_gige in the PHY init instead of passing the gigE
capability via function parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43333
Kernel 3.14 introduced a switch reset in phy_init_hw in drivers/net/phy
causing BMCR_ANENABLE to get cleared.
Due to the fact that ar8xxx_phy_config_aneg does nothing for
PHY 0 autonegatiation support remains disabled.
This can cause ports to operate at 10MBit/half-duplex only.
Fix this by calling genphy_config_aneg for PHY 0 too as
genphy_config_aneg sets BMCR_ANENABLE if it's not yet set.
Fixes: ticket 17800
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43332
PHY init code in the switch-specific hw_init functions is mainly
identical. Factor it out into a generic ar8xxx_phy_init function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43331
Move phy fixup code from the chip-specific hw_init functions into a
fixup_phys callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43330
Currently there is a fixed 1000ms wait time after the switch was reset.
Most if not all switches need much less time to perform a reset.
Therefore replace the fixed wait time with polling for BMCR_RESET to
be cleared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43329
All supported switches have 5 PHYs. Currently partially 5 is hardcoded
and partially switch-specific constants exist.
Replace them with a global constant.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43328
Without this patch the UBIFS driver is unable to attach to the mtd
storage and mount the root FS.
Fixes a kernel panic with Netgear WNDR4300/3700v4 devices.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
SVN-Revision: 43287
The patch adding AR8216_PHY_LEDS was not ported to more recent kernel
versions.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43139
Some changes from the header file were not ported from older kernel.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43137
The select SYS_HAS_DMA_OPS in CPU_CAVIUM_OCTEON was from the kernel
patch in 3.13, but it is only included in kernel 3.14 and not in 3.13
and 3.18, add it again.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43134
OpenWRT patch 255-lib80211_kconfig_hacks gives user possiblity to select
LIB80211 dependant settings (LIB80211_CRYPT_*) without having LIB80211
selected which is wrong.
My patch changes OpenWRT patch so LIB80211 is vissible and all
LIB80211_CRYPT_* options selects LIB80211 automatically.
Signed-off-by: Tomasz Wasiak <tjwasiak@gmail.com>
SVN-Revision: 43112
Boards that have more than one swconfig enabled switch will show the devices in
reverse order when call swconfig list. Fix this by using list_add_tail().
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43106
All platforms which are using 3.10.x at the moment are upgraded.
Changelogs:
https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.50https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.51https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.52https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.53https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.54https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.55https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.56https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.57https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.58
A new symbol 'X86_16BIT' appeared in 3.10.52 with commit 34273f41d57ee8d854dcd2a1d754cbb546cb548f
("x86-espfix-make-it-possible-to-disable-16-bit-support.patch")
I defaults to 'unset', but it's worth a discussion to enable it
("turn off support for any 16-bit software").
Also removed the patch 0db3db45f5bd6df4bdc03bbd5dec672e16164c4e
("fix build failure on memcpy() in decompress.c")
and is obsolete by commit 29593fd5a8149462ed6fad0d522234facdaee6c8 upstream.
included in kernel 3.10.56
compile tested on all platforms with:
make tools/install
make toolchain/install
make target/linux/compile
user@box:~/user/openwrt$ cat /tmp/log.txt
[Wed Oct 22 00:36:02 CEST 2014] ./smoketest.sh: ar71xx - OK
[Wed Oct 22 00:53:22 CEST 2014] ./smoketest.sh: ar7 - OK
[Wed Oct 22 01:08:27 CEST 2014] ./smoketest.sh: au1000 - OK
[Wed Oct 22 01:21:43 CEST 2014] ./smoketest.sh: avr32 - OK
[Wed Oct 22 01:37:47 CEST 2014] ./smoketest.sh: cns21xx - OK
[Wed Oct 22 01:52:05 CEST 2014] ./smoketest.sh: cns3xxx - OK
[Wed Oct 22 02:10:23 CEST 2014] ./smoketest.sh: gemini - OK
[Wed Oct 22 02:29:07 CEST 2014] ./smoketest.sh: ixp4xx - OK
[Wed Oct 22 02:44:01 CEST 2014] ./smoketest.sh: malta - OK
[Wed Oct 22 02:55:57 CEST 2014] ./smoketest.sh: mpc85xx - OK
[Wed Oct 22 03:07:56 CEST 2014] ./smoketest.sh: orion - OK
[Wed Oct 22 03:24:30 CEST 2014] ./smoketest.sh: ppc40x - OK
[Wed Oct 22 03:40:19 CEST 2014] ./smoketest.sh: ppc44x - OK
[Wed Oct 22 03:55:29 CEST 2014] ./smoketest.sh: realview - OK
[Wed Oct 22 04:09:47 CEST 2014] ./smoketest.sh: sparc - OK
[Wed Oct 22 04:23:37 CEST 2014] ./smoketest.sh: x86 - OK
[Wed Oct 22 04:35:56 CEST 2014] ./smoketest.sh: xburst - OK
run tested on x86, au1000, ar71xx, mpc85xx and brcm47xx
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43049
This is required due to 306-mips_mem_functions_performance.patch, just
add a memmove() implementation to satisfy the lzma2 decompressor code.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43036
This enables dedicated "rootfs" splitter by default. We still keep
CONFIG_MTD_SPLIT_SQUASHFS_ROOT, so the old (built-in) splitter will be
used as a fallback in case of problems.
Once we decide the dedicated partitioner works stable, we should remove
the old one completely.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42805
This allows tagged and untagged traffic together on the same port on ar8327
switch devices.
I looked at the first attempt to do this in r40777 (ar71xx: Fix tagged+untagged
operation on AR8327N (#12181)). I also set the vlan and port egress policies
like that change. But I change vlan_tagged in an less intrusive way. The
tagged/untagged decision is now based on the following rules:
- if vid != pvid then traffic is always tagged
- if vid == pvid then vlan_tagged stores if the traffic should be tagged
Tested on TP-Link WDR-3600 (ar8327N).
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
SVN-Revision: 42653
This moves ingress, egress policy and pvid decisions to setup_port methods.
They arenow device type dependent.
This allows policy changes on only one device type which is needed to allow
tagged + untagged operation on ar8327.
Tested on TP-LINK WDR-3600 (ar8327N).
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
SVN-Revision: 42652
Upstream bcma patch:
bcma: use separated function to initialize bus on SoC
was backported incompletely. I missed arch code change.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42603
We used separated patch for patches that were sent but not accepted yet.
It has changed now, so let's use the standard patch file for them.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42535
This series of patches ports back some fixes of the ad799x driver, which were
commited between 3.10 and 3.15.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 42523
There are pretty many OpenWrt patches against mtd subsystem resulting
in a bit of mess and growing maintenance cost.
My idea is to use an extra "mtdsplit" directory with OpenWrt specific
files (including Kconfig).
This is the first step to achieve this. This patch adds a "mtdsplit"
directory with Kconfig and replaces 4 patches with a single one.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42287
Upstream commit c11eede powerpc: add missing explicit OF includes for ppc was
included in 3.13 and onwards, hence making those patches obsolete.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42263
The GW16083 Ethernet Expansion Mezzanine adds the following to supported
Gateworks baseboards:
* 7-port Ethernet Switch
* 4x RJ45 ports (ENET1-4) supporing 802.11af/at PoE (with optional PoE module)
* 2x RJ45 ports or SFP module (ENET5-6) (auto-selected)
This series adds support for a phy driver that adds support for ENET5/ENET6
PHY adding initialization for those PHY's and a polling mechanism that detects
SFP insertion and configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42147
Fix IFF_NO_IP_ALIGN location which is collide with new netdev private flag
IFF_MACVLAN.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41992
This commit implements a new netfilter match "xt_id" which can be used to
attach unsigned 32bit IDs to iptables rules.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41945
This is a backport of bcma from wireless-tesing/master tag master-2014-07-29-1.
For kernel < 3.10 this only adds the header changes needed by more
recent b43 versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41899
This is a backport of bcma and ssb from wireless-tesing/master tag
master-2014-07-22.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41804
This fixes error erasing partial mtd partition which does not start on
eraseblock boundary and allows using fconfig to configure redboot on
devices such as the Gateworks Cambria.
Signed-off-by: Maciej Skrzypek <maciej.skrzypek@flytronic.pl>
SVN-Revision: 41733
Declare inline placeholder when usb_hcd_amd_remote_wakeup_quirk() not
compiled due CONFIG_PCI_DISABLE_COMMON_QUIRKS.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41702
Since kernel 3.11, the third parameter passed to notifier_call()
is of type struct netdev_notifier_info. This patch fixes an oops
when setting a netdev LED trigger.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 41552
According to the thread https://forum.openwrt.org/viewtopic.php?id=48281
b53 uses GPIO 7:
[ 4.470000] b53_common: [DBG] b53_switch_reset_gpio using 7
and causes device to self-reboot. GPIO 8 was found in CFE boot log:
"Reset switch via GPIO 8 ..."
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41526
This patch deactivates the statistics, adds a missing lock
initialization and fixes a waring.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41511
Spotted by several buildbots.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Patchwork: http://patchwork.openwrt.org/patch/5768/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41391
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41351
A modified version of 552-ubifs-respect-silent-mount-flag.patch has
been merged upstream. Replace the patch in OpenWrt with the version
which has been merged.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41218
Similar to the rootfs hacks on NOR flash devices, this series
introduces support for auto-attaching (ubi device), auto-creating
(ubiblock device) and mounting the "rootfs" (ubifs or squashfs)
volume.
This is needed so OpenWrt can start without relying on the bootloader
to pass the ubi.mtd, ubi.block, rootfs and rootfstype parameters, but
instead auto-detect the root filesystem according to a simple convention.
OpenWrt-specific:
490-ubi-auto-attach-mtd-device-named-ubi-or-data-on-boot.patch
491-ubi-auto-create-ubiblock-device-for-rootfs.patch
492-try-auto-mounting-ubi0-rootfs-in-init-do_mounts.c.patch
493-ubi-set-ROOT_DEV-to-ubiblock-rootfs-if-unset.patch
sent upstream:
552-ubifs-respect-silent-mount-flag.patch
http://lists.infradead.org/pipermail/linux-mtd/2014-May/053893.html
v2: actually retry with MS_RDONLY when mounting read-only ubifs root
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41119
It was augmented by CONFIG_USB_GADGET...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40986
550-ubifs-symlink-xattr-support.patch contains a reference to the
by now obsolete config symbol CONFIG_UBIFS_FS_XATTR which leads to
the functionality originally added by the patch in r30794 being
left-out during compile since commit 1bdcc63112a0
("UBIFS: remove xattr Kconnfig option") in v3.5.
Fix this by removing the #ifdef from all affected kernels as XATTR
support is now always enabled for UBIFS as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 40864
Revert the tagged + untagged rework for now due to regressions in
vlan setup on certain AR83xx switches.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 40842
Replace the global "vlan_tagged" variable with an array storing the
tagging state per vlan.
The code was taken from #12181, tested and cleaned up by Saverio Proto
with additional bug fixes supplied by Álvaro Fernández.
Tested-by: Jo-Philipp Wich <jow@openwrt.org>
Signed-off-by: Saverio Proto <zioproto@gmail.com>
Signed-off-by: Álvaro Fernández <noltari@gmail.com>
SVN-Revision: 40777
Function register_mtd_parser always returned 0 (at least since v3.3)
before being changed to return void in v3.14-rc1~65^2~93 (mtd: make
register_mtd_parser return void), so it's not needed to check the
return value of this function. Also add __init flag to caller.
This fix compile errors in 3.14 kernel like:
drivers/mtd/mtdsplit_seama.c: In function 'mtdsplit_seama_init':
drivers/mtd/mtdsplit_seama.c:99:2: error: void value not ignored as it ought to be
return register_mtd_parser(&mtdsplit_seama_parser);
^
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
SVN-Revision: 40731
With gcc-4.8 I get a compile error with kernel 3.3.
This patch fixes this problem by backporting a patch from a more recent kernel version.
CC arch/mips/mm/page.o
arch/mips/mm/page.c:89:6: error: 'clear_page' alias in between function and variable is not supported
void clear_page(void *page) __attribute__((alias("clear_page_array")));
^
arch/mips/mm/page.c:84:12: error: 'clear_page_array' aliased declaration [-Werror]
static u32 clear_page_array[0x120 / 4];
^
arch/mips/mm/page.c:108:6: error: 'copy_page' alias in between function and variable is not supported
void copy_page(void *to, void *from) __attribute__((alias("copy_page_array")));
^
arch/mips/mm/page.c:102:12: error: 'copy_page_array' aliased declaration [-Werror]
static u32 copy_page_array[0x540 / 4];
^
arch/mips/mm/page.c:108:6: error: 'copy_page' alias in between function and variable is not supported
void copy_page(void *to, void *from) __attribute__((alias("copy_page_array")));
^
arch/mips/mm/page.c:102:12: error: 'copy_page_array' aliased declaration [-Werror]
static u32 copy_page_array[0x540 / 4];
^
arch/mips/mm/page.c:89:6: error: 'clear_page' alias in between function and variable is not supported
void clear_page(void *page) __attribute__((alias("clear_page_array")));
^
arch/mips/mm/page.c:84:12: error: 'clear_page_array' aliased declaration [-Werror]
static u32 clear_page_array[0x120 / 4];
^
cc1: all warnings being treated as errors
make[7]: *** [arch/mips/mm/page.o] Error 1
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 40619
r40587 added some kernel config options, on which these two ones depend.
This fixes the build of the buildbots.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 40588
This patch adds port status information and MIB counters to the ADM6996
switch driver.
The driver supports also the older ADM6996L-variant, but I'm not able to
test this patch on that chip. According to the datasheet the same
registers exist there as well, so I think it should work, but any
feedback is appreciated.
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40542
This bgmac patch was an attempt to fix/workaround bug reported in
https://dev.openwrt.org/ticket/7198 noticed on WNR3500L.
Patch assumed length reported by the hardware was 0 and was trying to
read it until getting a different value. This was actually the opposite.
Lenghts were some invalid & huge values that resulted in skb_over_panic.
For example:
skbuff: skb_over_panic: text:83b21074 len:57222 (...)
skbuff: skb_over_panic: text:87af1024 len:43226 (...)
skbuff: skb_over_panic: text:87af5024 len:8739 (...)
So instead of that not-working patch checking for 0, write a new one
checking for huge values. In case something like that happens, dump
hardware state and drop the packet.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 40424
Export the ubi_num and vol_id into the sysfs record of the gluebi-
emulated mtd device. Previously userspace didn't have a way to
map gluebi-emulated devices back to their corresponding ubi volumes.
SVN-Revision: 40306
If the CPU port is not forced up, the link, at least on this board, is lost after
changes are applied. This makes sure that the link is restored. Regression tests
should confirm it doesn't break other boards.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40305
- hide port pvid - vlan index relation
- switch initialises with vlans disabled so port isolation is not used
- remove special treatment of cpu port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40304
Changes to:
- show the correct "enable_vlan" value under "Global attributes"
- show tagged ports under "Vlan: ports"
- use get_port_link method to report link status
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40303
Patch 642-bridge_port_isolate.patch needs to be updated
for kernels 3.12, 3.13 and 3.14 as the define for BR_ISOLATE_MODE
conflicts with BR_LEARNING
Signed-off-by: Jonas Eymann <j.eymann@gmx.net>
SVN-Revision: 39955
Now that GCC 4.8 is the default, make sure that we have the relevant
memset fixes to avoid nasty kernel crashes.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39902
This is a backport of code to improve the quality of fq_codel
hashing for 3.10 for some encapsulated protocols.
Not needed in 3.11 and later.
Patch-by: Dave Taht <dave.taht@bufferbloat.net>
Patchwork: http://patchwork.openwrt.org/patch/4902/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39640
This adds empty definitions for the PCI quirks functions when they
should not be included in the kernel.
This is based on a patch by Daniel <daniel@makrotopia.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39534
The int brnf_call_ebtables in the header should be extern, otherwise
every object file gets its own int and they will conflict when linking
the binary.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39533
Since the yaffs code update (r39084), it is not
possible to install OpenWrt on RouterBoards with
small-page NAND chips. Fix the yaffs code to make
it work again.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39409
Use the 'swconfig_trig_set_brightness' function to set
the brightness value of the LED when the link goes down.
This ensures that the last brighness value is saved into
a local variable which is used to track the actual LED
status.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39402
This reverts r38197.
The automatically created firmware partition includes
the partition_table partition. Apart from the partition
table, this partition contains sensitive data on some
Compex devices which data can be destroyed when the
firmware partition gets modified. Revert the change to
prevent that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39382
The HIFN driver is a PCI driver, thus requires PCI support to be enabled
to compile. Therefore let it depend on PCI..
Should fix mvebu builds.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39357
The PHY always says there is no link
Instead of doing this dma sync a mdelay does the same trick and it is as unreliable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39202
This updates the bgmac backport patch to the current upstream version
and adds some more patches mostly for BCM4707.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 39165
Without it in some occasions oops is shown on network restart. Problem was
noticed on imx6 targed.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 39134
Use the latest version of the yaffs code. Fetched from the
yaffs2 git tree and it is based on the following commit:
commit bc76682d93955cfb33051beb503ad9f8a5450578
Merge: 3a8580e ffa781d
Author: Charles Manning <cdhmanning@gmail.com>
Date: Thu Jul 11 17:46:25 2013 +1200
Merge branch 'master' of ssh://www.aleph1.co.uk/home/aleph1/git/yaffs2
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39084
This patch enables jumbo frames on AR8327 switch by default.
I have tested it on TP-Link TL-WDR3600.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39076
Linaro GCC 4.6-2013.05 incorrectly pads the arpt_arp structure on
at least the ar71xx target, resulting in a two bytes shorter struct
in the kernel compared to what arptables userspace expects.
When comparing sizeof(struct arpt_arp) in kernel and userspace, the
former yields 162 byte, while the latter is 164 byte.
As a consequence, the subsequent target_offset and next_offset
members of the parent arpt_entry structure contain invalid values
when processed by the arptables binary, leading to bad memory
accesses in the populate_cache() procedure, subsequently causing a
segfault.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 38999
This patch is needed to use the switch inside the Sitecom WLR-8100;
it was unusable and detected as Generic-Phy before.
since ar8337 is behaving like ar8327
generally do the same thing
see: https://forum.openwrt.org/viewtopic.php?pid=214218#p214218
forward-ported to trunk
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4469/
[juhosg: merge chip_is_ar83[23]7 statements in ar8xxx_phy_config_init]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38952
get_cycles() is used in some places as one part of the seed for the
kernel PRNG.
This backports the following commit from mainline linux kernel:
9c9b415c50bc298ac61412dff856eae2f54889ee
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38834
The BCM5365 needs a shift of 7 bits and not 6 bits like the BCM5325 for
the untagged ports.
Thank you Russell for reporting this and testing the patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38793
This adds some more code for bgmac core rev 4 and it now restarts all
cores when initializing the first one on BCM4708. I am just able to
send under 100 packages and then DMA TX does not work any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38714
This pci ID is used by sprom less BCM4313 devices.
This is a backport from the mainline kernel.
This is part of #13551.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38713
This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.
The GPIO bit banging protocol implementation was copied from the old
switch driver and adapted to this driver and changed to the mainline
kernel GPIO interface.
The ADM6996L is different from the ADM6996M which is supported, for
both specs are available in the Internet.
This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38698
The current code only allows to automatically set
root device on MTD partitions. Move the code to MTD
core to allow to use it with all MTD devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38643
Upstream commit c655bc6896b94ee0223393f26155c6daf1e2d148 changed number of
arguments in nf_ct_iterate_cleanup() function.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 38547
Upstream commit 9ddebc46 ("MIPS: OCTEON: Rename Kconfig
CAVIUM_OCTEON_REFERENCE_BOARD to CAVIUM_OCTEON_SOC") renamed a Kconfig
symbol, thus making all MIPS builds ask for this specific Kconfig
symbol, add it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 38535
Based on 'kernel: update x86 generic to 3.10.13' patch
from http://patchwork.openwrt.org/patch/4129/
Signed-off-by: Ulrich Weber <uw@xyne.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38498
Commit r37470 did not add a default conig for the ARM_ERRATA symbols for kernel 3.3.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38352
The bgmac driver will be used on the brcm47xx and the bcm53xx target.
These are only the patches already applied in current net-next/master
branch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38288
Add a new kernel config option for generic firmware partition
split support and change the uImage split support to depend on
the new option. Aslo rename the MTD_UIMAGE_SPLIT_NAME option to
MTD_SPLIT_FIRMWARE_NAME to make it more generic.
The patch is in preparation for multiple firmware format
support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38002
Separate OpenWrt specific MTD options from the mainline
option by moving those into a new submenu in the kernel
configuration interface.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37997
The revision is stored in a different register than it is in other
Broadcom switches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37995
These switches are integrated in some recent BCM53XX and BCM47XX SoCs
like the BCM53572.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37994
The Linksys wrt310n v1 does not have a robo_reset config variable in
nvram, but GPIO Pin 8 is the pin needed for resetting the external
switch, Linksys hard coded it into their source code.
Thank you Devastator for testing.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37988
- change patch numbers to group the related stuff together,
- add mtd prefix where it is missing,
- use hyphens in the patch names
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37974
The skb is usually started by a padding which allows the protocols in the
network stack to add their headers in front of the payload. The skb can be
reallocated in case the preallocated padding is not large enough. This can for
example happen in the function __skb_cow which will check the requested extra
headroom and allocate more buffer when the requested headroom is bigger than
the available one. The extra buffer is aligned again to the multiple of the
NET_SKB_PAD of the target architecture.
The macro used to create the multiple of the NET_SKB_PAD is written in a way
which allows only values power two as alignment parameter. The currently used
value of 48 bytes can not be written as n ** 2 but as 2 ** 4 + 2 ** 5. The
extra buffer is therefore not always the multiple of 48 but can be 16, 64, 80,
128, 144 and so on. The generated values are also not monotonic (48 requested
bytes are mapped to 80 allocated bytes and 49 requested bytes are mapped to 64
allocated bytes).
These unexpected small values result in more reallocations of the buffer. This
was noticed prominently during tests between two QCA9558 720 MHz devices which
were connected via ethernet to PCs and had a HT40 802.11n 3x3 link between each
other. The throughput PC-to-PC during iperf TCP runs increased reliable from
186 Mibit/s to 214 Mibit/s in one direction and from 195 Mibit/s to 220 Mibit/s
in the other direction. This is a performance increase of ~14% just by reducing
the amount of reallocations.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 37948
Currently, the module causes an oops at least on rt5350. These patches
have been accepted upstream at:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net.git
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 37931
BCM5365 (and probably other older variants) use a different phy id, so
the phy driver never attached for them.
Fix this by adding the appropriate phy id to the fixup and the phy
driver.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37906
b53_no_ops has no elements and b53_port_ops has one element, this makes
the code access some random memory when trying to access the mib
counter functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37895
The myloader partition parser code uses ifdef wrappers
to make the code usable on kernels below version 3.2.
All targets are using kernel 3.3 at least so the wraper
is not needed. Remove that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37880
The 'Warning: unable to open an initial console' message
indicates an error in the rootfs. Remove the patch which
hides the warning.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37848
Linux expects that the /dev/console node is present
in the rootfs image. Create the node in initramfs,
in order to make std{in,out,err} usable even in early
init process.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37846
Fixes the following build error on ramips/rt3883:
arch/mips/pci/pci-rt3883.c:488:3: error: implicit declaration of function \
'of_pci_get_devfn' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Although the function is only used by the PCI driver
of the RT3883 SoC but at the moment but it might be
useful for other targets as well.
Signed-off-by: Michael Lee <igvtee@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37826
vsnprintf returns the number of chars that would have been written, not
the actual number of chars written. This can lead to crashlog_buf->len
being too big which in turn can lead to get_maxlen() returning negative
numbers. The length argument of kmsg_dump_get_buffer will be casted to
a size_t which makes a negative input a big positive number allowing
kmsg_dump_get_buffer to write out of bounds.
Fix this by using vscnprintf which returns the actually written number
of chars.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 37820
The patch in question has been accepted upstream in commit:
55bf75b7dd8ec875d048824f3cdecf8254e292e5
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37807
Felix Fietkau
John Crispin
Imre Kaloz
Hauke Mehrtens
Rafał Miłecki
Zoltan Herpai
Florian Fainelli
Steven Barth
Luka Perkov
Jo-Philipp Wich
Gabor Juhos
Jonas Gorski
Nicolas Thill