Commit Graph

191 Commits (d2329f88f376e1e55d6d0377a27514681568a915)

Author SHA1 Message Date
Gabor Juhos 99a12119ca ar71xx: fix tl-wa901nd buttons code
This patch fixes the code of the buttons for TP-Link WA901ND.

Signed-off-by: Rocco Folino <lordzen@autistici.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37696
2013-08-05 09:09:39 +00:00
Gabor Juhos 6d8163505e ar71xx: add kernel support for the Netgear WNR612 v2 board
Netgear WNR612 v2:
 - cpu Atheros AR7240 (Python) @400MHz
 - flash 4MB
 - ram 32MB
 - ethernet 10/100: 1xwan + 2xlan (only two)
 - radio AR9285

[juhosg: use a separate kernel patch]

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3876/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37575
2013-07-28 10:23:36 +00:00
Gabor Juhos c5029c2ebf ar71xx: add kernel support for the TP-LINK TL-WR710N v1 board
Small router sold in EU: AR9330@400MHz, 1x USB2.0,
2x ethernet, 8MB flash, 32MB ram, one led, one button.

See: http://galeria.tech-blog.pl/TP-Link_TL-WR710N-EU/

[juhosg: use a separate kernel patch]

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3873/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37572
2013-07-28 10:23:32 +00:00
Gabor Juhos b49dc036e8 ar71xx: TEW632BRP has buttons 'active low', fix board config
Looks like trunk@37090 has changed the logic that determines
if router's button was pressed. This resulted in TEW632BRP
always booting into failsafe mode because it detected pressed
button (which was not pressed).

Measure with voltmeter has shown that buttons on this router
are actually active-low. This patch reflects this fact in
board configuration and fixes 'load info failsafe mode' issue.

Note: it looks like Trendnet TEW632BRP and a close relative
to TEW-652BRP V1.0 and D-Link DIR-615C1, so same problem may
exist on those routers as well. This patch doesn't affect
routers other than 632BRP and unfortunately I do not have
hardware to test this issue with other routers.

This patch fixes #13893 and is tested on actuall Trendnet
TEW632BRP.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37569
2013-07-28 10:23:22 +00:00
Gabor Juhos ec7fe3fab7 ar71xx: add kernel support for the TL-MR10U board
Based on andelf's patch:
http://andelf.diandian.com/post/2013-05-22/40050677370

[juhosg: extend WR703N code to handle the TL-MR10U
instead of adding a separate mach-tl-mr10u file]]

Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3840/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37547
2013-07-26 07:31:57 +00:00
Felix Fietkau 25d910a78f ar71xx: use uimage split for WZR-HP-G300NH2
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 37295
2013-07-14 14:05:31 +00:00
Felix Fietkau 6bff456212 ar71xx: enable uimage split for wzr-hp-ag300h/wzr-600dhp
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 37294
2013-07-14 14:05:27 +00:00
Felix Fietkau fbde376c53 ar71xx: use uimage split for WZR-HP-G300NH
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 37293
2013-07-14 14:05:23 +00:00
Felix Fietkau a7c5f6708b ar71xx: use uimage split for WZR-HP-G450H
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 37292
2013-07-14 14:05:19 +00:00
John Crispin 39531131a9 ar71xx: add carambola2 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 37260
2013-07-11 21:16:53 +00:00
Gabor Juhos e61a77a05c ar71xx: disable JTAG on TL-WR841N-v8/MR3420v2
It also fixes USB Power on MR3420v2.

Signed-off-by: Dmytro <dioptimizer@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37194
2013-07-08 08:40:21 +00:00
Gabor Juhos ca02639d17 ar71xx: fix for wrong eth0 mac assignment on Netgear WNDAP360
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 37192
2013-07-08 08:40:18 +00:00
Luka Perkov c9926f77b4 ar71xx: Buffalo WZR-HP-AG300H (600DHP) change button type
switch buttons should be declared as switch so the failsafe shell is not
triggered by accident in procd

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 37131
2013-07-02 10:45:32 +00:00
Gabor Juhos 5bb2e8030d ar71xx: add support for WIFI button on tp-link tl-mr3220v2
The TP-LINK TL-MR3220 v2 has a button on the left side
labeled "WIFI". This is GPIO 24. This patch adds the
support for this button.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36848
2013-06-04 13:25:54 +00:00
Gabor Juhos da66ea52ec ar71xx: register USB port for RB2011U* devices
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36801
2013-05-30 17:38:31 +00:00
Gabor Juhos 151dca0935 ar71xx: make the SFP port usable on RB2011*S boards
The port 6 of the switch is connected to the SFP
cage on the RB2011*S boards. Add a helper function
to correctly initialize the switch configuration
data on those boards to make the SFP port usable.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36799
2013-05-30 17:38:28 +00:00
Gabor Juhos 3467b17e69 ar71xx: rb2011: add switch led control values
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36796
2013-05-30 17:38:21 +00:00
Gabor Juhos 4cf6e53ccc ar71xx: rb2011: update RGMII RX/TX delay values
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36795
2013-05-30 17:38:20 +00:00
Gabor Juhos 6da63a8793 ar71xx: rb2011: move NAND nCE init to rb2011_nand_init
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36794
2013-05-30 17:38:17 +00:00
Gabor Juhos d6554bf66a ar71xx: add kernel support for the RB2011UAS
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36792
2013-05-30 17:38:13 +00:00
Gabor Juhos 91d7c3efc1 ar71xx: add kernel support for the TP-LINK Archer C7 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36788
2013-05-30 16:23:07 +00:00
Gabor Juhos 93ce462b7e ar71xx: set eth0 mac address to match bottom label of the OM2P LC
Signed-off-by: marek@open-mesh.com
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36723
2013-05-26 16:02:29 +00:00
Felix Fietkau 144cfb65a4 ar71xx: add hard_cfg offset detection for rb2011 support - fixes wlan on some newer devices
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 36631
2013-05-13 19:13:33 +00:00
Gabor Juhos 10b3ca5ccb ar71xx: add kernel support for Netgear WNDAP360
Here is corrected version (only thing not working are wifi LEDs).

[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]

Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36578
2013-05-08 17:03:34 +00:00
Gabor Juhos 9b3c0d11a2 ar71xx: Add Netgear WNR2000v3 support
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.

Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36459
2013-04-26 17:00:52 +00:00
Gabor Juhos 5c11773f8a ar71xx: add kernel support for TPLINK WR720N v3
Add support for TPLINK WR720N v3 which has 4MB flash,
32MB ram, 2 ethernet interfaces, 1 USB 2.0 port.

The patch is mostly a modification from mach-tl-wr703n.c.
GPIO numbers for the slider switch is from mach-tl-mr3020n.c.

Tested on my device and they worked fine.

Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36456
2013-04-26 17:00:48 +00:00
Gabor Juhos f7da2127ab ar71xx: fix ethernet LEDs on the TL-WDR3500
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36122
2013-03-25 06:40:03 +00:00
Gabor Juhos cd5cca4ba8 ar71xx: fix USB power GPIO on the TL-WDR3500
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36119
2013-03-24 19:23:47 +00:00
Gabor Juhos 4daefc9480 ar71xx: remove numeric suffix of the TL-WDR3500 USB LED
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36118
2013-03-24 19:23:45 +00:00
Gabor Juhos 35d41db979 ar71xx: rw2458n - Use eeprom (art) from wifi card
Use eeprom (art) from included wifi card, not hard coded in flash.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36037
2013-03-15 14:35:50 +00:00
Gabor Juhos 8deffcba7e ar71xx: Error fix in Kernel for MR3420v2 Ethernet Switch configuration
Error in using another MDIO (AP123 platform using only one GE1 device
for eth0 and eth1) for the router mr3420v2.
?onfirmed: https://forum.openwrt.org/viewtopic.php?pid=194779#p194779

Routers in this sense are the same and the only difference is: USB
port, USB led, instead of the GPIO-switch we have GPIO-button.

Signed-off-by: Dmytro <dioptimizer@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 36036
2013-03-15 14:35:48 +00:00
Gabor Juhos 14ca5fc98b ar71xx: om2p-hs: use correct bit mask to disable JTAG functionality
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35966
2013-03-11 19:52:54 +00:00
Gabor Juhos 902dd27383 ar71xx: add kernel support for MR3420v2
[juhosg: use gpio_request_one to enable the USB power]

Patch-by: Dmytro <dioptimizer@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@opewrt.org>

SVN-Revision: 35961
2013-03-11 15:55:20 +00:00
Gabor Juhos 5c5e1c0a9d ar71xx: enabling control GPIO14 and GPIO15 on MR3040/MR11U
LAN1 and LAN2 LEDs not present (it pulled to ground via
resistors) on MR3040 and MR11U devices. This little patch
enabling ability to control GPIO14 and GPIO15.

Patch-by: Dmytro <dioptimizer@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3439/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35960
2013-03-11 15:55:19 +00:00
Gabor Juhos a7525f5f5d ar71xx: add kernel support for dir-835-a1
[juhosg:
  - remove custom mdio bus info and platform data for ar8327, clear the
    .led_cfg field from dir835a1_setup instead,
  - remove arguments of dir835c1_generic_setup function, register the
    LEDs directly from the board specific setup instead]

Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Patchwork: http://patchwork.openwrt.org/patch/3426/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35957
2013-03-11 15:55:13 +00:00
Gabor Juhos 1d55249d7c ar71xx: use backported QCA955x patches
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35878
2013-03-04 11:48:15 +00:00
Luka Perkov a5ebfc79ba ar71xx: rework changes from r35840
Signed-off-by: Luka Perkov <luka@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35865
2013-03-03 21:59:34 +00:00
Gabor Juhos 4491da2bd4 ar71xx: update MAC address assignment for dir-825-c1
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35855
2013-03-03 12:47:37 +00:00
Gabor Juhos 200aa6db83 ar71xx: fixes leds for dir-825-c1
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35854
2013-03-03 12:47:33 +00:00
Luka Perkov 107e0c6d1f ar71xx: add support for Buffalo WZR 600DHP
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 35840
2013-03-01 13:46:01 +00:00
Gabor Juhos bcac3c5569 ar71xx: fix MAC address assignment on the DIR-825-Bx boards
Use the same MAC addresses as the original firmware.

Based on a patch from #10421.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Tested-by: Gabor Varga <vargagab@gmail.com>

SVN-Revision: 35730
2013-02-21 17:58:21 +00:00
Gabor Juhos 4341b11f3e ar71xx: remove __dev{init,exit} annotations from kernel files
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35687
2013-02-19 20:52:06 +00:00
Gabor Juhos 7a709573d7 ar71xx: add kernel support for the Mikrotik RB951G board
This is platform definition for the RB951G device. It's mostly rework
of RB2011UAS patchset with network taken from the RB751 patches.
The main difference is the flash layout used by this device.

[juhosg:
  - remove dead code from mach-rb951g
  - add "-2HnD" suffix to the machine name
  - use a separate 615-MIPS-ath79-RB951G-support.patch]

Patchwork: http://patchwork.openwrt.org/patch/3257/
Signed-off-by: Kamil Trzcinski <ayufan@ayufan.eu>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35633
2013-02-17 10:08:35 +00:00
Jonas Gorski f07a33afc2 ar71xx: register the micro sd card reader on RB493G
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 35535
2013-02-10 12:31:38 +00:00
Gabor Juhos 6ff973bdda ar71xx: Routerboard 751 Mac Address Offset Fix
We utilize many Routerboard 751's and discovered that our latest batch
of RB751's would not initialize the wireless radio. We have determined
Mikrotik has changed where the mac address was located inside hardconfig.
As such we utilize "routerboot_find_tag" to find the location of the mac
address. We should remove "RB751_MAC_ADDRESS_OFFSET" as it is ambiguous
by machine manufacturing date. The newer batch of RB751's that we received
had a RB751_MAC_ADDRESS_OFFSET 0x10.

Signed-off-by: Davey Hutchison <dhutchison@bluemesh.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35519
2013-02-08 09:34:53 +00:00
Gabor Juhos 7c87d28054 ar71xx: fixes whitespaces for dir-825-c1
Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35455
2013-02-02 15:02:19 +00:00
Gabor Juhos 31af0dc186 ar71xx: fix mac address calculation on the OpenMesh MR600
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35446
2013-02-02 08:47:41 +00:00
Gabor Juhos 8837d3a49b ar71xx: add kernel support for the OpenMesh MR600v2
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35428
2013-02-01 15:50:42 +00:00
Gabor Juhos fe3db74276 ar71xx: remove unused OpenMesh MR6000 platform code
Signed-off-by: Marek Lindner <marek@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35426
2013-02-01 15:50:37 +00:00
Gabor Juhos 5bd02ca895 ar71xx: add kernel support for the TL-WDR3500 board
WDR3500 is similar to WDR3600 except it doesn't have gigabit ethernet,
and has only 1 USB port.

Pending issues:

  * Leds are not working at all (except power and wlan_5g)
  * LAN switch ethernet ports are reversed with respect to case label.

  [Label] -> soft device
  [LAN1] -> eth0.4
  [LAN2] -> eth0.3
  [LAN3] -> eth0.2
  [LAN4] -> eth0.1

Based on http://patchwork.openwrt.org/patch/3208/

Thanks-to: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35423
2013-02-01 15:50:29 +00:00
Gabor Juhos 800da21cb1 ar71xx: add kernel support for dir-825-c1
[juhosg:
 - remove unused GPIO stuff
 - use a separate kernel patch for machine integration]

Signed-off-by: Alexander Stadler <sa.maillists@univie.ac.at>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35401
2013-01-29 22:50:50 +00:00
Gabor Juhos 5ca187570f ar71xx: add kernel support for Atheros AP132 Reference Board
Based on http://patchwork.openwrt.org/patch/3162/

Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35395
2013-01-29 19:12:30 +00:00
Gabor Juhos 8a9d92f125 ar71xx: fix ethernet device registration for the QCA9556 SoC
Based on http://patchwork.openwrt.org/patch/3162/

Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35394
2013-01-29 19:12:28 +00:00
Gabor Juhos df15e5cd61 ar71xx: enable fast flash read on dual-flash devices
This improves flash read speed on various Buffalo units.

mtd_speedtest results on the WZR-HP-AG300H:

                          old         new        delta
eraseblock read speed:  726 KiB/s   2068 KiB/s   +184.85%
page read speed:        699 KiB/s   1973 KiB/s   +182.26%
2 page read speed:      711 KiB/s   2043 KiB/s   +187.34%

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35392
2013-01-29 19:12:25 +00:00
Gabor Juhos ba4de984b9 ar71xx: disable PHY_SWAP and PHY_ADDR_SWAP bits on TL-WR703N/MR3020/MR3040/MR11U boards
The PHY_SWAP and PHY_ADDR_SWAP bits are initialized
differently by different versions of the bootloader.
This leads to broken ethernet connection with OpenWrt
on some boards.

Turn both SWAP bits OFF on these boards to make it
consistent regardless of the bootloader used.

Based on a patch by Michel Stempin <michel.stempin@wanadoo.fr>.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 35037
2013-01-07 14:30:37 +00:00
Gabor Juhos 66efec6783 ar71xx: allow to register the NAND flash controller on the QCA955x
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34945
2013-01-01 13:10:36 +00:00
Gabor Juhos 5dec87afef ar71xx: fix ethernet device registration for QCA9558
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34853
2012-12-22 12:12:48 +00:00
Gabor Juhos 4085a5773d ar71xx: fixup allowed PHY interface types for QCA9558
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34851
2012-12-22 12:12:44 +00:00
Gabor Juhos f01a786825 ar71xx: don't assign any MII bus device on QCA9558 by default
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34850
2012-12-22 12:12:43 +00:00
Gabor Juhos a0b31f97bb generic: ar8216: rename cpuport_cfg to port0_cfg in ar8327_platform_data
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34846
2012-12-22 12:12:35 +00:00
Gabor Juhos 0767605d17 ar71xx: add kernel support for the TL-MR3220 v2
Based on the following patch:
http://patchwork.openwrt.org/patch/3043/

[juhosg:
 - remove custom LED and button arrays
 - use separate machine specific patch
 - update Kconfig]

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34779
2012-12-19 08:50:35 +00:00
Gabor Juhos bc82db7d78 ar71xx: add kernel support for the NETGEAR WNDR4300
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34647
2012-12-12 16:49:49 +00:00
Gabor Juhos 75b71f4a74 ar71xx: add ap91_pci_init_simple helper
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34646
2012-12-12 16:49:48 +00:00
Gabor Juhos 1f7ae58a2c ar71xx: ar934x_nfc: allow to control DMA data swap via platform data
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34588
2012-12-10 10:38:07 +00:00
Gabor Juhos d44d954dec ar71xx: add kernel support for the RB435G board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34239
2012-11-18 10:18:01 +00:00
Gabor Juhos d62bddc620 ar71xx: update PCI IRQ map for RB4xx devices
Should fix #12269.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34238
2012-11-18 09:51:04 +00:00
Gabor Juhos 8d4857d677 ar71xx: add kernel support for the OpenMesh MR600 board
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34231
2012-11-18 09:32:33 +00:00
Gabor Juhos 91bab828aa ar71xx: add support for TP-Link TL-WA7510N
It is mostly the same as TL-WA901N. WLAN and LAN
are working. LAN LED is working. WLAN signal
strength LEDs are not working yet.

http://wiki.openwrt.org/toh/tp-link/tl-wa7510n?s[]=wa7510n

[juhosg:
  - cleanup commit message
  - move non kernel related stuff into separate changes
  - rename and refresh 615-MIPS-ath79-TL-WA7510N-v1-support patch
  - merge WA7510N support into the mach-tl-wa901nd.c file
  - add 3.6 support]

Signed-off-by: Stefan Helmert <helst_listen@aol.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34187
2012-11-13 14:48:00 +00:00
Gabor Juhos f2528b1792 ar71xx: use gpio_request_one instead of ath79_set_usb_power_gpio
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34087
2012-11-05 13:23:27 +00:00
Gabor Juhos ed35253f4c ar71xx: don't use the unknown LED on the ZCN-1523-5 board
According to #12421, GPIO 1 controls the power
output on the unused lines of the LAN2 port.
Remove the LED definition in order to prevent
possible permanent hardware damage.

If someone needs that, the power-out feature can
be controlled via the GPIO sysfs interface.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34076
2012-11-04 22:08:54 +00:00
Gabor Juhos 7228a91a3b ar71xx: fix link speed between AR7242 and AR8327 on the RB750GL/RB751G boards
The default pll_1000 value had to be changed
in order to make it working.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33993
2012-10-29 17:24:30 +00:00
Gabor Juhos d54c9653e9 ar71xx: add support for the Senao CAP4200AG board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33956
2012-10-27 08:55:38 +00:00
Gabor Juhos f1f388d527 ar71xx: rw2458n - fix flash parts
See #12338. Redwave rw2458 has uboot, not redboot.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33867
2012-10-19 18:32:49 +00:00
Gabor Juhos 31387947c8 ar71xx: use the ath79_set_ar934x_eth_cfg helper in machine setup routines
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33818
2012-10-17 18:27:47 +00:00
Gabor Juhos 5ffc08e3dc ar71xx: add a helper function for setting up ETH_CFG register on AR934x
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33817
2012-10-17 18:27:45 +00:00
Gabor Juhos c5a32cfc92 ar71xx: add support for the OpenMesh OM2P-HS board
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 33800
2012-10-17 08:26:01 +00:00
Gabor Juhos 196c6c5b45 ar71xx: add support for the TL-WR841N/ND v8 board
SVN-Revision: 33621
2012-10-04 20:16:03 +00:00
Gabor Juhos 170cd7a19a ar71xx: avoid possible NULL pointer dereference in ath79_init_{,local}_mac
SVN-Revision: 33575
2012-09-27 20:05:42 +00:00
Gabor Juhos e7b1949d87 ar71xx: automatically find WLAN calibration data on TEW-673GRU
SVN-Revision: 33539
2012-09-25 12:57:40 +00:00
Gabor Juhos 8ed8e51e74 ar71xx: automatically find WLAN calibration data on DIR-825-B1
SVN-Revision: 33538
2012-09-25 12:57:38 +00:00
Gabor Juhos e70ad61e44 ar71xx: use different machtype and setup for the TL-MR3040
Should fix #12211. Compile tested only.

SVN-Revision: 33535
2012-09-24 18:45:56 +00:00
Gabor Juhos 5804b9d1b7 ar71xx: register the NAND controller device on the RB2011
SVN-Revision: 33388
2012-09-13 07:26:26 +00:00
Gabor Juhos 4fd67c3cd4 ar71xx: add device registration code for the AR934x NAND flash controller
SVN-Revision: 33387
2012-09-13 07:26:25 +00:00
Gabor Juhos aa2f4d4c8d ar71xx: add initial support for RB2011UAS-2HnD
SVN-Revision: 33349
2012-09-09 14:05:32 +00:00
Gabor Juhos 3686e18727 ar71xx: use routerboot_find_tag to find wlan data offset on RB751
SVN-Revision: 33348
2012-09-09 14:05:30 +00:00
Gabor Juhos ccabe4a1b4 ar71xx: add RouterBoot related helper routines
SVN-Revision: 33347
2012-09-09 14:05:28 +00:00
Gabor Juhos 44bf7c7cc1 ar71xx: define MTD partitions for RB2011
SVN-Revision: 33345
2012-09-09 14:05:24 +00:00
Gabor Juhos 6ae5ec16e0 ar71xx: add preliminary support for Mikrotik RB2011L
This patch adds preliminary support for the Mikrotik RB2011L.
The NAND flash is not yet supported, so only the initramfs
kernel can be used for now.

[juhosg: remove unnecessary PCI/USB related stuff, the board
does not use that, update commit message]

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

SVN-Revision: 33344
2012-09-09 14:05:22 +00:00
Gabor Juhos 94bac7366c ar71xx: use dynamic clock dividers on the 2nd MDIO of AR934x
SVN-Revision: 33343
2012-09-09 14:05:20 +00:00
Gabor Juhos 88a5478781 ar71xx: use the RLE library for RB751
SVN-Revision: 33338
2012-09-08 17:51:56 +00:00
Gabor Juhos 11c3392b7f Revert "ar71xx: only allow RGMII mode on the 2nd ethernet MAC of the AR7240"
That was based on assumptions.

SVN-Revision: 33310
2012-08-29 10:37:55 +00:00
Gabor Juhos eb9a97a360 ar71xx: all0315n: fix ethernet according to vendor info
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33309
2012-08-29 10:37:54 +00:00
Gabor Juhos 5fdbb33db4 ar71xx: Buffalo WZR-HP-AG300H LED support
An improved LED support for Buffalo WZR-HP-AG300H.

There will be two new packages to go with this patch
(ar922x-led-fix-hotplug and ar922x-led-fix-init).
These packages essentially perform the same task of
disabling "JTAG over GPIO pins" function which is
currently required for LEDs on AR922x emac GPIO to work,
and are both considered a temporary fix that circumvent
this problem.

[juhosg: add the hotplug script from the proposed
ar922x-led-fix-hotplug package to ar71xx/base-files]

Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>

SVN-Revision: 33294
2012-08-29 10:11:55 +00:00
Gabor Juhos eebdd633e4 ar71xx: add support for the Allnet ALL0315N board
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33281
2012-08-27 14:55:31 +00:00
Gabor Juhos cca873e8e0 ar71xx: only allow RGMII mode on the 2nd ethernet MAC of the AR7240
Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33280
2012-08-27 14:55:26 +00:00
Gabor Juhos 8b3d95bba9 ar71xx: add support for the TRENDnet TEW-712BR board
SVN-Revision: 33231
2012-08-22 20:09:13 +00:00
Gabor Juhos 2811d6c183 ar71xx: fix comment style in mach-tl-wr2543n.c
SVN-Revision: 33227
2012-08-22 12:42:59 +00:00
Gabor Juhos 5a694e09c8 ar71xx: add ALL0305 board alias
For the pure convenience of having a correctly named
image and system name in /proc/cpuinfo , until we can
do that by having system names in DTS...

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 33224
2012-08-22 12:33:22 +00:00
Gabor Juhos 0517183b9c ar71xx: add support for TP-Link TL-WDR3600
The TL-WDR3600 is identical to the TL-WDR4300 with the exception that is has
only two antennas.

[juhosg: remove the custom machine type, change the board name instead]

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 33219
2012-08-22 09:43:18 +00:00
John Crispin 968ac3fd03 add led defintion for the WR2543 5GHz WLAN LED
Signed-off-by: Andy Leiserson <andy@leiserson.org>

SVN-Revision: 33215
2012-08-22 09:10:24 +00:00