Commit Graph

13273 Commits (3b701e8023138fda298617f95dbab0e52cca0e55)

Author SHA1 Message Date
Felix Fietkau f35da063bc targets: remove useless quotes around KERNELNAME
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42780
2014-10-05 20:17:19 +00:00
Zoltan Herpai fbbce1c8d8 sunxi: re-add rootfs build when no profile is set, fixes #17980, thanks.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42775
2014-10-05 17:32:36 +00:00
Jonas Gorski 14ebb012a4 brcm63xx: fix wrong fixups pointer
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42756
2014-10-03 11:03:58 +00:00
Rafał Miłecki 7436b17075 bcm53xx: build R6250 firmware with "Other Regions" region
This prevents vendor firmware from warning about incompatible region.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42754
2014-10-03 10:40:12 +00:00
Felix Fietkau 156b296b20 ar8216: set the pvid based on runtime state instead of port number to fix learning with enable_vlan = 0
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42753
2014-10-02 20:00:41 +00:00
Rafał Miłecki 66922082ed bcm53xx: early support for Netgear R6300 V2
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42743
2014-10-02 19:30:08 +00:00
Jonas Gorski 2fa8a656a6 brcm63xx: update spw500v sprom to values from gpl tarball
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42740
2014-10-02 12:26:36 +00:00
Jonas Gorski 60cb45427e brcm63xx: reorder some patches according to their upstream state
The irq rewrite was accepted upstream.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42739
2014-10-02 12:26:19 +00:00
Jonas Gorski 57214b00ae brcm63xx: Add DT support for 96368MVWG
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42738
2014-10-02 12:26:07 +00:00
Jonas Gorski 477826ef31 brcm63xx: Add DT support for 96368MVNgr
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42737
2014-10-02 12:25:57 +00:00
Jonas Gorski cdea47cbc3 brcm63xx: Add DT support for 96358VW2
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42736
2014-10-02 12:25:41 +00:00
Jonas Gorski 80db30b508 brcm63xx: Add DT support for 96358VW
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42735
2014-10-02 12:25:36 +00:00
Jonas Gorski e7ade47fba brcm63xx: Add DT support for 96338W
Renamed of_board_id to convention.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42734
2014-10-02 12:25:27 +00:00
Jonas Gorski d9194da882 brcm63xx: Add DT support for 96338GW
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42733
2014-10-02 12:25:22 +00:00
Jonas Gorski 73f576dff2 brcm63xx: Add DT support for 96348R
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42732
2014-10-02 12:25:13 +00:00
Jonas Gorski 35cf1adfc6 brcm63xx: Add DT support for 96348GW-11
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42731
2014-10-02 12:25:07 +00:00
Jonas Gorski eaee4e3eb7 brcm63xx: Add DT support for 96348GW-10
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42730
2014-10-02 12:25:01 +00:00
Jonas Gorski 73d59ed675 brcm63xx: Add DT support for 96348GW
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42729
2014-10-02 12:24:39 +00:00
Jonas Gorski 99ecfbf702 brcm63xx: Add DT support for 96345GW2
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42728
2014-10-02 12:24:34 +00:00
Jonas Gorski a950e2fce8 brcm63xx: Add DT support for 963281TAN
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42727
2014-10-02 12:24:29 +00:00
Jonas Gorski ddcc29290c brcm63xx: fix brcm63xx fallback typo
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42726
2014-10-02 12:24:14 +00:00
Rafał Miłecki 28301ea0b1 bcm53xx: early buttons support (without interrupts)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42718
2014-10-02 12:05:58 +00:00
Rafał Miłecki bd12c49473 bcm53xx: backport bcma RFC patch that fixes LEDs
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42717
2014-10-02 10:42:30 +00:00
Rafał Miłecki 01ab343779 bcm53xx: support devices with more (13+) partitions
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42716
2014-10-02 09:51:54 +00:00
Rafał Miłecki bbae0f7df0 bcm53xx: select LEDs support by default
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42715
2014-10-02 05:54:18 +00:00
Rafał Miłecki 1421516e65 bcm53xx: add BCM5301X patches sent upstream (bus and R6250 LEDs)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42711
2014-10-01 13:38:50 +00:00
Rafał Miłecki 59b965194d kernel: update bcma to the tag master-2014-09-30 (wireless-next)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42710
2014-10-01 13:37:36 +00:00
Rafał Miłecki 26e85084b5 bcm53xx: rename BCM5301X DTS patch to match upstream order
SVN-Revision: 42708
2014-10-01 07:59:03 +00:00
Zoltan Herpai 175aad61d4 sunxi: add profile for Olimex A13 SOM
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42693
2014-09-28 23:21:59 +00:00
Hauke Mehrtens a6616a6e48 bcm53xx: activate some workarounds for errors in the Cortex-A9
BCM4708 uses a Cortex-A9 rev r3p0 and a L2C-310 rev r3p2.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42690
2014-09-28 18:03:33 +00:00
Felix Fietkau 61f960071d ar71xx: revert accidental kernel upgrade
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42687
2014-09-27 20:54:12 +00:00
Felix Fietkau 3e833dcf90 ar71xx: add wmac callback for reading soc revision on ar934x
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42685
2014-09-27 20:52:05 +00:00
Felix Fietkau 84d81d5844 ar71xx: refresh 3.14 kernel patches
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42684
2014-09-27 20:51:49 +00:00
Florian Fainelli 54a18b3fe8 brcm2708: switch to 3.14
Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42681
2014-09-27 19:11:55 +00:00
Florian Fainelli 3f5cc1882b brcm2708: add 3.14 support
Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42680
2014-09-27 19:11:37 +00:00
Florian Fainelli 04c0ef5263 kernel: add missing CONFIG_BACKLIGHT_GPIO to 3.14
Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42679
2014-09-27 19:11:06 +00:00
Florian Fainelli 6918ea2484 brcm2708: update 3.10 patches with raspberrypi/rpi-3.10.y of 27 Apr. 2014
Update the 3.10 rasperry patches by rebasing raspberry/rpi-3.10-y
against linux-stable/v3.10.49.

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42678
2014-09-27 19:10:51 +00:00
Rafał Miłecki 71a03fb168 kernel: merge two mtdpart.c patches
It does not make sense to add some code and remove is 4 patches later.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42673
2014-09-27 09:44:24 +00:00
Rafał Miłecki 8e525a43b4 kernel: update bcma to the tag master-2014-09-26 (wireless-next)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42672
2014-09-27 07:49:48 +00:00
Florian Fainelli e5ef34ba02 realview: add protocol argument to ucidef_set_interface_raw
Now that ucidef_set_interface_raw() has been updated to take a protocol
argument, use that.

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42666
2014-09-25 19:09:17 +00:00
Rafał Miłecki 747fd7871c bcm53xx: add a patch that fixes booting problems
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42659
2014-09-24 21:08:17 +00:00
Felix Fietkau 38a8f5ae63 ar71xx: ar8216: tagged+untagged on ar8327 (#12181)
This allows tagged and untagged traffic together on the same port on ar8327
switch devices.

I looked at the first attempt to do this in r40777 (ar71xx: Fix tagged+untagged
operation on AR8327N (#12181)). I also set the vlan and port egress policies
like that change. But I change vlan_tagged in an less intrusive way. The
tagged/untagged decision is now based on the following rules:
- if vid != pvid then traffic is always tagged
- if vid == pvid then vlan_tagged stores if the traffic should be tagged

Tested on TP-Link WDR-3600 (ar8327N).

Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>

SVN-Revision: 42653
2014-09-23 10:19:58 +00:00
Felix Fietkau 1c675ee9be ar71xx: ar8216: move policies, pvid to setup_port
This moves ingress, egress policy and pvid decisions to setup_port methods.
They arenow device type dependent.

This allows policy changes on only one device type which is needed to allow
tagged + untagged operation on ar8327.

Tested on TP-LINK WDR-3600 (ar8327N).

Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>

SVN-Revision: 42652
2014-09-23 10:18:38 +00:00
Zoltan Herpai 9c43ea9a8b mxs: remove 3.13
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42651
2014-09-23 06:42:29 +00:00
Zoltan Herpai 5105e10608 mxs: disable mmc debugging
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42650
2014-09-23 06:38:58 +00:00
Rafał Miłecki f036f5801f bcm53xx: image: use IMG_PREFIX for chk images
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42649
2014-09-22 18:11:09 +00:00
Rafał Miłecki 23a07c6d18 bcm53xx: image: make filesystem a suffix for TRX files
This makes TRX files more /compatible/ with firmware files (e.g. CHK).
This will allow us to put some TRX files in BIN_DIR if we need to.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42646
2014-09-22 09:16:20 +00:00
Rafał Miłecki fd515112db bcm53xx: image: document arguments of various functions
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42645
2014-09-22 08:37:18 +00:00
Rafał Miłecki 5f7be0ebf4 bcm53xx: image: rework Makefile and merge some functions
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42644
2014-09-22 08:04:26 +00:00
Zoltan Herpai 144c9992a2 sunxi: enable GPIO_SYSFS
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42643
2014-09-22 06:15:45 +00:00
Hauke Mehrtens 182e1dbcd4 bcm53xx: activate vfpv3 support
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42642
2014-09-21 21:58:29 +00:00
Hauke Mehrtens 47aefcc563 bcm53xx: add nand flash driver
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42641
2014-09-21 21:58:02 +00:00
Hauke Mehrtens 2c6e0e0ae0 bcm53xx: update patches adding bcma support
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42640
2014-09-21 21:57:17 +00:00
Hauke Mehrtens c977fad4fd bcm53xx: add fixtrx
Without running fixtrx the image will not boot at the second time,
because the CRC the boot loader check is invalid at that time.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42639
2014-09-21 21:56:31 +00:00
Rafał Miłecki 223a309c3c bcm53xx: add support for GPIOs
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42638
2014-09-21 21:18:30 +00:00
Rafał Miłecki 2468f9201f bcm53xx: rename console fixing patch
This squeezes BCM5301X patches.

SVN-Revision: 42637
2014-09-21 21:02:38 +00:00
Zoltan Herpai 158336df6c sunxi: add AXP209 to pcDuino3
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42636
2014-09-21 20:31:18 +00:00
Zoltan Herpai aaa430b434 sunxi: enable AXP209 on BananaPi as well
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42635
2014-09-21 17:46:50 +00:00
Zoltan Herpai 6f3abd92c5 sunxi: enable AXP209 regulator
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42634
2014-09-21 17:45:20 +00:00
Zoltan Herpai aa0848bba2 sunxi: add sunxi-ir module
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42631
2014-09-21 16:28:06 +00:00
Zoltan Herpai e6d53c1366 sunxi: add support for infra receiver on A20, along with IR-related backports from 3.15
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42630
2014-09-21 16:25:45 +00:00
Zoltan Herpai e02dd2f19c kernel: add missing symbols for 3.14
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42629
2014-09-21 16:24:28 +00:00
Zoltan Herpai cc60fad010 sunxi: remove 3.13 support
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42628
2014-09-21 15:42:36 +00:00
John Crispin d4cc995c53 ramips: D-Link DIR-810L. Add support for SoC 2.4 GHz wireless and fix leds naming
SVN-Revision: 42619
2014-09-19 11:07:08 +00:00
John Crispin d731d14362 lantiq: set 3.14 as default
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42618
2014-09-19 10:52:47 +00:00
John Crispin 4ef1237545 ralink: drop dwc_otg support. dwc2 seems stable
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42617
2014-09-19 10:52:37 +00:00
Zoltan Herpai 3dc7dc9cde sunxi: update gmac with adding correct regulators on bananapi
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42616
2014-09-19 00:13:49 +00:00
Zoltan Herpai 384ef8ece1 sunxi: backport late clock fixes from 3.15
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42615
2014-09-19 00:12:53 +00:00
Zoltan Herpai 3a22a37f1a sunxi: update dts for pcduino3 and bananapi with regulators
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42608
2014-09-17 23:45:08 +00:00
Zoltan Herpai 46d7c59487 sunxi: add usb ohci support
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42607
2014-09-17 23:34:10 +00:00
Zoltan Herpai 240f04765f sunxi: add default interface for bananaPi
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42606
2014-09-17 23:15:30 +00:00
Zoltan Herpai 4aafe1bc4d sunxi: add missing symbol for arch timer
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42605
2014-09-17 23:12:50 +00:00
Rafał Miłecki da74f722e1 kernel: fix backport of bcma init patch
Upstream bcma patch:
bcma: use separated function to initialize bus on SoC
was backported incompletely. I missed arch code change.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42603
2014-09-17 21:25:36 +00:00
Jo-Philipp Wich 057e518224 sdk: predefine kernel version magic
Kernel modules which are built using the SDK do not have access
to the .vermagic file in the Linux build dir, therefore the
generated .ipk metadata depends on kernel versions like
'3.10.49-1-unknown' which are not satisfiable by the kernel
meta package in the image.

Fix this problem by substituting 'unknown' with the current
version magic in include/kernel.mk when packing the SDK.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 42590
2014-09-17 10:25:47 +00:00
Zoltan Herpai 4bf83f89e0 sunxi: add arm arch timer support
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42589
2014-09-17 10:15:05 +00:00
Hauke Mehrtens 150224d91e kernel: add missing config option
This missing option was found by the build bots.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42583
2014-09-16 21:39:24 +00:00
John Crispin 944820584a Lantiq: fix build warning from dsl_fs script
fix inclusion of functions.sh in dsl_fs init script

without this, the following error is seen during build:
./etc/init.d/dsl_fs: line 4: /lib/functions.sh: No such file or directory

Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>

SVN-Revision: 42575
2014-09-16 14:53:06 +00:00
John Crispin 3dd93e8336 lantiq: move the lantiq,switch property into the interface node
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42574
2014-09-16 14:53:01 +00:00
John Crispin 44249f71a8 postinst trigger: the new postinst trigger broke IB
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42571
2014-09-16 11:56:19 +00:00
Zoltan Herpai 78726df7bd sunxi: add new watchdog compats to reboot code in 3.14
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42558
2014-09-15 21:05:00 +00:00
Zoltan Herpai 8ef9dec08f sunxi: update profile of A13-OLinuXino to match uboot boardname, required for sdcard image
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42557
2014-09-15 19:37:23 +00:00
John Crispin 7dbbdfb61f ar71xx: add qihoo 360 c301 router support
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.

This patch adds its initial support.

v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 42552
2014-09-15 10:19:38 +00:00
John Crispin b520e9b8d4 lantiq: fix switch init on vr9 SoC (3.10)
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42551
2014-09-15 10:19:27 +00:00
John Crispin 32f47538b9 lantiq: fix switch init on vr9 SoC
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42550
2014-09-15 10:19:20 +00:00
John Crispin cb37fe5ca5 ar71xx: add board support for ubnt loco m xw
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 42549
2014-09-15 10:19:14 +00:00
John Crispin 2c4c6d135b ar71xx: refactor ubnt xw board setup
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 42548
2014-09-15 10:19:01 +00:00
John Crispin f16f310306 lantiq: add default switch setup to td8970
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42544
2014-09-15 10:18:37 +00:00
Hauke Mehrtens 9434dfee87 bcm53xx: fix early serial console
This device actually has a 8250 serial with a shift of 0.
Tested this on a BCM4708.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42538
2014-09-14 19:22:49 +00:00
Rafał Miłecki 7cd532623e kernel: update bcma to the tag master-2014-09-11 (wireless-next)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42537
2014-09-14 17:31:13 +00:00
Hauke Mehrtens f032f66318 kernel: add missing config option
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42536
2014-09-14 15:00:33 +00:00
Rafał Miłecki a9d06501b2 kernel: move bcma patches pushed to wireless-next
We used separated patch for patches that were sent but not accepted yet.
It has changed now, so let's use the standard patch file for them.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42535
2014-09-14 14:58:13 +00:00
Zoltan Herpai fb985d741f sunxi: add sdcard image generation support when board profile is selected
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42534
2014-09-14 13:47:42 +00:00
Zoltan Herpai e3cc78e9d8 sunxi: rename pcduino profile to match uboot boardname in prep for the sdcard generator
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42533
2014-09-14 13:09:22 +00:00
Hauke Mehrtens 61d02a8df4 kernel: add missing config option
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42532
2014-09-14 12:06:59 +00:00
Hauke Mehrtens d56a44040d kernel: do not deactivate CONFIG_BLK_DEV
CONFIG_BLK_DEV does not activate any functionality, but many code, but
makes it possible to activate other options. Deactivating this breaks
the build of kmod-zram.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42528
2014-09-13 22:10:00 +00:00
Hauke Mehrtens eb35b82275 kernel: add missing config options
These missing option were found by the build bots.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42527
2014-09-13 21:25:21 +00:00
Hauke Mehrtens 9a428dd8d5 kernel: Backport essential fixes for ad799x
This series of patches ports back some fixes of the ad799x driver, which were
commited between 3.10 and 3.15.

Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>

SVN-Revision: 42523
2014-09-13 20:34:44 +00:00
Hauke Mehrtens 180ee041fa bcm53xx: select nvram package by default
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42522
2014-09-13 20:28:44 +00:00
John Crispin 80ff3af16f atheros: refresh config
Remove symbols that are now placed in the generic config.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42513
2014-09-12 06:54:16 +00:00
John Crispin cb5902d603 atheros: convert AR2315 GPIO code to platform driver
Convert gpiolib realization to platform driver and move to the
appropriate subdirectory. Misc GPIO interrupt acknowledgement placed
to the MISC IRQ handler since in fact we can detect only one GPIO state
change.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42512
2014-09-12 06:54:10 +00:00
John Crispin a8799105d7 atheros: convert AR5312 GPIO code to platform driver
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42511
2014-09-12 06:54:05 +00:00
John Crispin 0e86c116cb atheros: rework chained interrupts handling
Call generic_handle_irq() instead of do_IRQ() for chained interrupts,
remove XXX_NONE interrupts and call spurious_interrupt() when an interrupt
is unexpected.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42510
2014-09-12 06:53:58 +00:00
John Crispin d780abcbbc atheros: convert gpio.h to stub
Implement to_irq() handler for AR2315 GPIO chip and convert custom
gpio.h header to stub.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42509
2014-09-12 06:53:53 +00:00
John Crispin 6f874d84d5 atheros: rename SoCs config symbols
Rename config symbols to be consistent with other SoCs config symbols
supported by MIPS arch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42508
2014-09-12 06:53:48 +00:00
John Crispin 413736e5f8 atheros: add AR2316 and AR2318 SoCs detection
Tested with AR2315, AR2316 and AR2317 SoCs, not tested with AR2318 but
changes seems correct: revision is one more than AR2317.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42507
2014-09-12 06:53:43 +00:00
John Crispin c883854f7e atheros: ar2315-pci: convert to platform driver
Convert the PCI controller support code to platform driver and move it to
appropriate subdirectory.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42506
2014-09-12 06:53:33 +00:00
John Crispin 4156c9734a atheros: ar2315-pci: rename configuration symbol
Rename configuration symbol to be consistent with other MIPS machines.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42505
2014-09-12 06:53:27 +00:00
John Crispin fb4196ec2a atheros: ar2315-pci: update DMA offset macroses
Remove duplicated macroses, which define DMA offset (SDRAM baseaddress).

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42504
2014-09-12 06:53:21 +00:00
John Crispin 94efeaa51f atheros: ar2315-pci: update host bridge resources
It seems that the PCI controller does not support I/O ports, so remove
the ports range. Also correct the beginning of the memory range and its
size.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42503
2014-09-12 06:53:15 +00:00
John Crispin 78c914ffe5 atheros: ar2315-pci: rework the configuration access code
Use __raw_{read,write}l accessors and use Abort interrupt to detect a
configuration space read/write errors. The second change improves errors
detection, what improves the device presence detection and helps us to
avoid following (and similar) errors:

pci 0000:00:00.2: ignoring class 0x7e0200 (doesn't match header type 02)
pci 0000:00:00.2: bridge configuration invalid ([bus 03-90]), reconfiguring
pci 0000:00:00.2: not setting up bridge for bus 0000:01

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42502
2014-09-12 06:53:09 +00:00
John Crispin dbdd8906ac atheros: ar2315-pci: rework interrupt handling
Add PCI IRQ controller to facilitate interrupt handling, move interrupts
initialization to the IRQ controller initialization from
pcibios_plat_dev_init() callback.

Also remove odd PCI dev configuration manipulation from pcibios_plat_dev_init()
callback.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42501
2014-09-12 06:53:00 +00:00
John Crispin 0f645cbd83 atheros: ar2315-pci: rework host controller initialization
Explicitly configure PCI host controller, and do not expose it to PCI
subsystem. The PCI host controller acts as a usual PCI device connected
to the bus, but its configuration as a usual PCI device is senseless,
since the host controller provide access to _internal_ memory space for
_external_ device.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42500
2014-09-12 06:52:55 +00:00
John Crispin 37d2445fcb atheros: ar2315-pci: cosmetic changes
- add comment, which briefly describes PCI controller features and
   Fonera 2.0g schematics.
 - rename several functions and structures, to make it clear that this
   code only for AR2315 chips.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42499
2014-09-12 06:52:51 +00:00
John Crispin 1e6af86ff9 atheros: ar2315-pci: remove odd locking in PCI config space access function
Caller (generic PCI code) already do proper locking so no need to add
another one here.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42498
2014-09-12 06:52:46 +00:00
John Crispin 09f38a3f76 atheros: remove odd ATHEROS_AR2315 config symbol dependencies
Remove options which already selected by ATHEROS_AR231X on which
ATHEROS_AR2315 depends.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42497
2014-09-12 06:52:42 +00:00
John Crispin 2e9deed90a atheros: various space related changes
- remove odd blank lines
 - remove odd spaces after casts
 - fix alignment

 No functional changes.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42496
2014-09-12 06:52:36 +00:00
John Crispin d34c3e0674 atheros: rework and cleanup board initialization
- remove odd flags and branching
  - add __init mark
  - make shorter variables names
  - returns true or false from boolean functions
  - unwrap short function declarations
  - unwrap quoted string
  - rename macroses with names in CamelCase

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42495
2014-09-12 06:52:26 +00:00
John Crispin 98b6a56b3c atheros: update ether addresses handling
- use ether_foo() routines to work with addresses
 - use ETH_ALEN inplace of magic '6'

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42494
2014-09-12 06:52:21 +00:00
John Crispin bdc1357e7b atheros: remove useless includes
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42493
2014-09-12 06:52:14 +00:00
John Crispin 300021d6c4 atheros: ar231x-eth: remove useless IOCTL handlers
These IOCTLs handled in the core now.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42492
2014-09-12 06:52:07 +00:00
John Crispin a28fd0dfd0 atheros: ar2315-spiflash: use mutex inplace of spinlock
Use mutex inplace of spinlock to make code simple, also call
mutex_{lock,unlock} explicitly to avoid sparse warning about context
imbalance.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42491
2014-09-12 06:52:00 +00:00
John Crispin ffa6091eef atheros: ar2315-spiflash: update initialization
- fill module metadata
  - remove odd module_{init,exit}

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42490
2014-09-12 06:51:51 +00:00
John Crispin 7a4cf9adfd atheros: ar2315-spiflash: use devm_* API to simplify the code
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42489
2014-09-12 06:51:46 +00:00
John Crispin f9e46af383 atheros: remove useless return
Remove useless void function return.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42488
2014-09-12 06:51:39 +00:00
John Crispin 9055970e92 atheros: remove FSF mailing address
Remove FSF mailing address as suggested by checkpach and place license
URL.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42487
2014-09-12 06:51:33 +00:00
John Crispin 7aaaef6b4a atheros: add blank line after declarations
as suggested by checkpach.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42486
2014-09-12 06:51:26 +00:00
John Crispin 5b4e53f59f atheros: use static keywork for local code
Make PCI IRQ handler and several structures static as suggested by
sparse.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42485
2014-09-12 06:51:10 +00:00
John Crispin 9b5f1a4f33 atheros: use NULL instead of plain integer
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42484
2014-09-12 06:51:05 +00:00
John Crispin d4113b1055 atheros: add missing include
Missing this headers cause several sparse "symbol 'foo' was not
declared. Should it be static?" warnings.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42483
2014-09-12 06:50:58 +00:00
John Crispin 60922d0013 atheros: avoid extern prototypes
Avoid using of extern prototypes as suggested by checkpatch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 42482
2014-09-12 06:50:53 +00:00
John Crispin 17cf9c4593 ralink: drop 3.10 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42481
2014-09-12 06:50:46 +00:00
John Crispin 18b5d72d83 lantiq: update 3.14 patches
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42476
2014-09-11 17:49:57 +00:00
Luka Perkov 02629d8f87 kernel: update 3.14 to 3.14.18
Targets were build tested and patches are refreshed.

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42463
2014-09-10 21:40:19 +00:00
Felix Fietkau c772d71d05 atheros: enable the low_mem flag to better deal with 16M RAM devices
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42460
2014-09-10 13:50:10 +00:00
Felix Fietkau 1961f8cdb7 ar71xx: ack completed tx descriptors only after the full frame has been completed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42457
2014-09-10 12:56:24 +00:00
Luka Perkov 9ccacbaa40 imx6: fix image build for Generic profile.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 42455
2014-09-09 21:15:49 +00:00
Hauke Mehrtens 54cd991725 kernel: drop 3.9 support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42452
2014-09-08 19:55:36 +00:00
Hauke Mehrtens eea3a89a6a gemini: drop kernel 3.9 support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42451
2014-09-08 19:55:00 +00:00
Hauke Mehrtens d0d537a039 gemini: switch to kernel 3.10
This switches to kernel 3.10 that was prepared by Hauke in r41531 :
    gemini: add support for kernel 3.10

    This is compile tested only, please run test and report back.

I've simply checked if it still compiles, unfortunately we didn't get
any feedback for this target.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42450
2014-09-08 19:54:22 +00:00
Hauke Mehrtens a446681bc6 omap: add kernel 3.14 support
It has been compile-tested only so far. Please give it a try.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42449
2014-09-08 19:53:01 +00:00
Hauke Mehrtens 8313b329c6 kernel: add bcma patches sent upstream but not pushed yet
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42448
2014-09-08 19:50:53 +00:00
Hauke Mehrtens e030c50502 kernel: update bcma to the version from wireless-testing master-2014-09-04 tag
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42447
2014-09-08 19:50:11 +00:00
John Crispin 4662c3b847 ralink: dwc_otg->dwc2
the old dwc_otg driver is starting to fall apart and fails on newer 3g
modems and some storage devices. switch to the upstream dwc2 driver which
is no longer in staging/.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42446
2014-09-08 17:33:16 +00:00
John Crispin bdba024c7b ralink: add dwc2 device_reset() call
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42445
2014-09-08 17:32:52 +00:00
John Crispin a4eae94a9c lantiq: add ath9k led pin support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42437
2014-09-08 14:29:18 +00:00
Zoltan Herpai d4a2aa4f92 sunxi: re-add lradc driver in 3.14
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42436
2014-09-08 07:50:03 +00:00
Felix Fietkau 60b81acd60 ath79: dev-eth: Don't advertise 1gbit in link code word on ar9331
While the AR9331 has a gigabit MAC towards the internal switch, the
integrated PHYs however are only 100-base-tx capable.  The existing code
however advertieses gigabit capability in the link status word.  If you
attach such a PHY to a gigabit capable switch on the remote end, with
some probability it attempts to negotiate gigabit and fails, falling
baco to the AR9331 assuming a 10mbit half-duplex link.  This has been
observed quite frequently with the Carambola2 and gigabit capable
switches.

In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
for both AR9331 ethernet ports. This is most likely wrong. Despite the
two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
100base-T PHY via MII. The has_gbit attribute is used in the ethernet
driver to determine the supported link modes.

So either pdata->has_gbit is not set to 1 anymore, or the ethernet
driver needs to be modified to determine the advertised link code word
on another criteria than pdata->has_gbit.  This patch implements the
former solution.

Signed-off-by: Harald Welte <laforge@gnumonks.org>

SVN-Revision: 42432
2014-09-07 09:45:32 +00:00
Felix Fietkau 60eeadd0ba ar71xx: re-enable descriptor splitting on ar716x after the previous bugfixes (#13072)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42429
2014-09-06 17:51:48 +00:00
Felix Fietkau 2da2317fed ar71xx: fix off-by-one error in packet descriptor splitting (patch from #13072)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42428
2014-09-06 17:51:44 +00:00
Felix Fietkau 05dd36a980 ar71xx: on ar716x, split ethernet packets in 512 byte chunks instead of 256 (improves performance) (patch from #13072)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42427
2014-09-06 17:51:39 +00:00
Felix Fietkau efa2159e17 atheros: remove linux 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42426
2014-09-06 17:51:35 +00:00
Zoltan Herpai 044bf28357 sunxi: bump kernel to 3.14.16
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42425
2014-09-06 15:59:06 +00:00
Zoltan Herpai b217763e41 sunxi: update pcDuino3 profile to the new u-boot
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42424
2014-09-06 15:57:08 +00:00
Zoltan Herpai 6833e90f0c sunxi: update Bananapi profile to the new u-boot
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42423
2014-09-06 15:23:30 +00:00
Nicolas Thill 4ea085316e uml: bump to 3.14.16
Signed-off-by: Nicolas Thill <nico@openwrt.org>

SVN-Revision: 42421
2014-09-05 22:02:09 +00:00
Florian Fainelli d2a420fa22 at91: build images for AT91SAMA5D3XPLAINED
Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42418
2014-09-03 03:11:25 +00:00
Florian Fainelli 7175e520e1 at91: add SAMA5D3 subtarget
Add a subtarget for Atmel's SAMA5D3 Cortex-A5 based SoCs.

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42417
2014-09-03 03:11:11 +00:00
Florian Fainelli 00c0f4f27a at91: move legacy Kconfig options to subtarget
Some Kconfig options are only relevant for the legacy platforms, move
them where they belong

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42416
2014-09-03 03:10:59 +00:00
Florian Fainelli 640579bf49 at91: switch to 3.14
We need a new kernel version to support Cortex-A5 based platforms such
as SAMA5GD3.

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42415
2014-09-03 03:10:47 +00:00
Florian Fainelli 892d571d07 at91: add 3.14 support
Add support for Linux 3.14 for the Atmel's AT91 platform.

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42414
2014-09-03 03:10:18 +00:00
Florian Fainelli 035f68e858 at91: move 3.10 specific files and patches
In preparation for adding 3.14 kernel support, move files and patches to
a separate per-version directory since some of them will have
incompatible changes (e.g: dts)

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42413
2014-09-03 03:09:51 +00:00
Florian Fainelli 132676f1ac at91: add Kconfig symbol for CONFIG_USB_ATMEL_USBA
Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42412
2014-09-03 03:09:36 +00:00
Florian Fainelli 5efbc41cbb at91: fix typo on Calao
Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42410
2014-09-03 03:09:14 +00:00
Florian Fainelli c2b92f9ef4 at91: create a legacy subtarget
In preparation for adding SAMA5D3 support, move the legacy ARMv5 based
platforms to a separate subtarget.

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42408
2014-09-03 03:08:51 +00:00
Felix Fietkau 366007c3d8 omap: remove 3.12 kernel patches
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42401
2014-09-02 17:00:46 +00:00
Felix Fietkau 1839d1b912 cns3xxx: support isolated PCI interrupts on newer Laguna PCBs
The cns3xxx uses irq61 for pcie0_intr which in the case of a PCIe-to-PCI
bridge ends up combining INTA/B/C/D on a single ARM CPU interrupt. This is
not optimal when you have multiple cores. To overcome this limitation an
enhancement was made on newer Laguna PCB's that support miniPCI cards
to route the INTA/B/C/D signals to unique external ARM CPU interrupts which
can help balance CPU core utilization and in some cases increase overall
system performance or responsiveness.

For more details see:
 http://trac.gateworks.com/wiki/multicoreprocessing#PCIInterruptsteering

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 42400
2014-09-02 16:44:40 +00:00
Felix Fietkau 734f7609b9 sdk: keep $(STAGING_DIR)/usr/bin, at least curl needs it
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42397
2014-09-01 22:34:37 +00:00
Felix Fietkau 7632358add imagebuilder: remove postinst files before generating image
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42339
2014-08-31 11:06:31 +00:00
John Crispin f11bd56f31 ipx806x: bump to 3.14.16
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42336
2014-08-30 09:59:30 +00:00
John Crispin 4d96ccd87a target: set myself as maintainer
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42335
2014-08-30 09:59:18 +00:00
John Crispin 3c1f6e358d ipq806x: Add support for IPQ806x chip family
Patches are generated using the "format-patch" command from the
following location:
*https://www.codeaurora.org/cgit/quic/kernel/galak-msm/log/?h=apq_ipq_base
*rev=0771849495b4128cac2faf7d49c85c729fc48b20
Patches numbered 76/77/102/103 have already been integrated in 3.14.12,
so they're not in this list.

All these patches are either integrated are pending integration into
kernel.org, therefore these patches should go away once the kernel
gets upgraded to 3.16.

Support is currently limited to AP148 board but can be extended to other
platforms in the future.

These changes do not cover ethernet connectivity.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 42334
2014-08-30 09:32:58 +00:00
Felix Fietkau 926f000b99 ar71xx: disable ethernet descriptor splitting for now, as it seems to cause tx hangs in some setups
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42333
2014-08-30 09:11:41 +00:00
Florian Fainelli a5a309142c kirkwood: fix typos on DEBUG_LL_UART_*
We were prompted for which DEBUG_LL_UART implementation we want, fix the
typos such that the build continues.

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42332
2014-08-30 00:32:05 +00:00
Felix Fietkau 4ff324191f ar71xx: select m25p80 support instead of spi support where used by mach files (#17699)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42331
2014-08-29 21:10:39 +00:00
Felix Fietkau 2c680151e4 ar71xx: split packets into multiple descriptors on ar716x
This improves performance when doing concurrent rx/tx on a single
ethernet MAC, e.g. when routing between VLANs.

Fixes #13072

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42328
2014-08-29 19:42:08 +00:00
John Crispin d1f8b9bd76 ralink: DIR-645 picks up incorrect MAC address in DTS file
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42321
2014-08-28 09:19:56 +00:00
John Crispin 254b2670e1 ar71xx: add Support for RB2011UiAS-2HnD
SVN-Revision: 42317
2014-08-28 06:27:45 +00:00
John Crispin e47fbcbf1d lantiq: BTHOMEHUBV2B use bigger mtd partition for kernel
The bb-rc3 image for the BTHOMEHUBV2B is too big for its
mtd partition. This patch corrects the partition sizes in
the device tree. This patch should really go in before
bb-final, otherwise the BTHOMEHUBV2B images won't be useable.
I do apologise for not spotting this straight away.

Many thanks,

Ben

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 42316
2014-08-28 06:27:41 +00:00
John Crispin 24a6617585 ramips: unbreak i2c for 3.14
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42315
2014-08-28 06:05:36 +00:00
Luka Perkov 0d165a244d kirkwood: refresh kernel config
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42314
2014-08-27 17:14:09 +00:00
Zoltan Herpai f10f009609 sunxi: initial 3.14 patchset
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42313
2014-08-27 12:09:46 +00:00
John Crispin 1349ebb5ba ralink: set 3.14 as default
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42305
2014-08-26 13:12:12 +00:00
Felix Fietkau 315e567ab2 target/toolchain: strip files, leave out the initial gcc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42302
2014-08-26 12:32:51 +00:00
Luka Perkov 20f48d27ea imx6: refresh patches
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42297
2014-08-25 21:50:49 +00:00
Luka Perkov 89d908e9f1 kernel: 3.14: refresh patches
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42296
2014-08-25 21:50:48 +00:00
Luka Perkov b13e12819b kernel: 3.14: backport for igb driver resolving a driver crash
Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 42295
2014-08-25 21:50:47 +00:00
Luka Perkov eb75d320d1 imx6: kernel: backport upstream fix for IMX6DL 800MHz speed grade
A previous backported patch that adds freq/voltage operating points for the
IMX6DL processor can cause hang/crash (general instability) on IMX6DL
processors in the industrial/automative speed grades as they don't support
1GHz operation.

This adds another backported patch from mainline that uses IMX6 fuse settings
to properly remove invalid operating points for the particular CPU grade used.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 42294
2014-08-25 21:50:43 +00:00
John Crispin 0c14bea523 ralink: the mt7620 evb has a usb port
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42293
2014-08-25 16:31:13 +00:00
John Crispin d3d9d55cde ralink: a few 3.14 related fixes
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42292
2014-08-25 16:31:09 +00:00
John Crispin 843fc45e27 ralink: fix mt7620 ohci 3.14
the ohci phy was not reset properly

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42291
2014-08-25 16:31:05 +00:00
John Crispin ca737049d2 ralink: fix mt7620 ohci 3.10
the ohci phy was not reset properly

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42290
2014-08-25 16:31:01 +00:00
John Crispin 3d00a1109e ralink: mt7620 has obchi/ehci and not dwc2
fix the default package selection

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42289
2014-08-25 16:30:57 +00:00
John Crispin c9813699b6 kernel: add own Kconfig for OpenWrt mtdsplit drivers
There are pretty many OpenWrt patches against mtd subsystem resulting
in a bit of mess and growing maintenance cost.
My idea is to use an extra "mtdsplit" directory with OpenWrt specific
files (including Kconfig).
This is the first step to achieve this. This patch adds a "mtdsplit"
directory with Kconfig and replaces 4 patches with a single one.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42287
2014-08-25 16:30:44 +00:00
John Crispin 67cf439237 ar71xx: use ETH_ALEN for consistency
Signed-off-by: Forest Crossman <cyrozap@gmail.com>

SVN-Revision: 42280
2014-08-25 06:35:58 +00:00
John Crispin 79c04e1897 ar71xx: enable sysupgrade for the EnGenius ESR900
Signed-off-by: Forest Crossman <cyrozap@gmail.com>

SVN-Revision: 42279
2014-08-25 06:35:54 +00:00
John Crispin fdc41e2fd7 ramips: enable second SPI for VoCore
This patch enables the second SPI as spidev and also fixes some typos.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42277
2014-08-25 06:35:46 +00:00
John Crispin a3fd3dc796 ramips: second spi device on rt5350
This is based on Jon Smirl's patch with the following changes:
- Set CS polarity as low by default.
- Add support for changing CS polarity.
- Add support for changing LSB/MSB.
- Add support for changing SPI mode.
- Fix indentations.

I tested it on a VoCore. Works fine connected to a second flash, but fails to detect MMC/SD cards due to SPI clock speed.

Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42276
2014-08-25 06:35:42 +00:00
Hauke Mehrtens 823659f458 bcm53xx: update bcma device tree intergeneration and fix nvram parsing
This fixes lots of sparse and checkpatch errors and extends the
documentation.

This also fixes a problem in the nvram parser, it now detects the
correct nvram on my Netgear R6250.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42272
2014-08-24 15:57:49 +00:00
Florian Fainelli fcfd0cec76 kernel: remove obsolete 322-ppc4xx-crypto-compile-fix.patch patches
Upstream commit c11eede powerpc: add missing explicit OF includes for ppc was
included in 3.13 and onwards, hence making those patches obsolete.

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42263
2014-08-23 02:42:03 +00:00
Hauke Mehrtens cc3545d165 bcm53xx: add bcm53xxspiflash driver for SPI flashes
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42260
2014-08-21 21:11:04 +00:00
Hauke Mehrtens b118879cc3 bcm53xx: backport more spi-nor patches
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42259
2014-08-21 21:10:29 +00:00
Jonas Gorski 51e1f1476f brcm63xx: Add DT support for P870HW-51a
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: fix nvram partition offset]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42248
2014-08-21 11:28:59 +00:00
Jonas Gorski b339304425 brcm63xx: Add DT support for HG553
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: fix linux partition length]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42247
2014-08-21 11:28:54 +00:00
Jonas Gorski 2f09960e46 brcm63xx: Add DT support for HG520v
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: fix nvram partition offset]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42246
2014-08-21 11:28:46 +00:00
Jonas Gorski 7bc83fdd13 brcm63xx: Add DT support for A4001N
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42245
2014-08-21 11:28:43 +00:00
Jonas Gorski a180c80f23 brcm63xx: Add DT support for A4001N1
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42244
2014-08-21 11:28:40 +00:00
Jonas Gorski 83651bad85 brcm63xx: Add DT support for WAP-5813n
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: make linux partition writable]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42243
2014-08-21 11:28:37 +00:00
Jonas Gorski 7b2d74a156 brcm63xx: Add DT support for VR-3025un
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: make linux partition writable]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42242
2014-08-21 11:28:34 +00:00
Jonas Gorski 42bbf7bcb3 brcm63xx: Add DT support for VR-3025u
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: make linux partition writable]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42241
2014-08-21 11:28:32 +00:00
Jonas Gorski 2936cacdfc brcm63xx: Add DT support for AR-5387un
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42240
2014-08-21 11:28:28 +00:00
Jonas Gorski b97aa0b4fd brcm63xx: Add DT support for AR-5381u
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42239
2014-08-21 11:28:18 +00:00
Jonas Gorski 1891b08f00 brcm63xx: Add DT support for CT-6373
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: make linux partition writable]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42238
2014-08-21 11:28:14 +00:00
Jonas Gorski e490cc7e14 brcm63xx: Add DT support for CT-5365
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: make linux partition writable]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42237
2014-08-21 11:28:10 +00:00
Jonas Gorski e46d57b3af brcm63xx: use DT for partitions on SPW500V
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42236
2014-08-21 11:28:01 +00:00
Jonas Gorski 84001352fd brcm63xx: dts: fix spelling of "bank-width"
Fixes pflash registration through DT for 6338/6345/6348.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42235
2014-08-21 11:27:56 +00:00
Jonas Gorski 33e2a51d4d brcm63xx: dsl-274xb-c: linux partition should not be read-only
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42234
2014-08-21 11:27:44 +00:00
John Crispin e9e519a147 ramips: fix OMNI-PLUG.dts
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42232
2014-08-21 06:41:27 +00:00
Hauke Mehrtens f66a0912f7 bcm53xx: add SPI controller driver
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42223
2014-08-19 20:14:06 +00:00
Hauke Mehrtens bcb36cd494 bcm53xx: backport spi nor code form kernel v3.17-rc1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42222
2014-08-19 20:12:36 +00:00
Hauke Mehrtens a8bdf2f1e0 kernel: update bcma to code from v3.17-rc1
This is needed for some new patches.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42221
2014-08-19 20:06:24 +00:00
Hauke Mehrtens 4a9acacf53 kernel: 3.14: update bcm47xxpart
It it used by brcm47xx and bcm53xx targets, so put patches in generic.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42212
2014-08-18 21:57:54 +00:00
Jonas Gorski 770ba9d40f brcm63xx: enable fallback sprom for Speedport W500 V
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42211
2014-08-18 21:50:45 +00:00
Jonas Gorski ddbff6a198 brcm63xx: tag images/dtbs with profiles
This prevents generating every supported image, except for de "Default" profile.
Also fixes Neufbox 6 image generation.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42210
2014-08-18 21:50:42 +00:00
Jonas Gorski 3db93a3351 brcm63xx: add profiles for DTB supported devices
Remove generic profiles and add profiles for each DTB supported device.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42209
2014-08-18 21:50:40 +00:00
Jonas Gorski 84ea696e03 brcm63xx: move generic profiles to top dir and remove smp profiles
Use generic profiles for brcm63xx instead of having similar profiles for
each subtarget.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42208
2014-08-18 21:50:37 +00:00
Jonas Gorski 4e708346cd brcm63xx: simplify HG556a image generation
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42207
2014-08-18 21:50:34 +00:00
Jonas Gorski 29e4d82dbb brcm63xx: fix HG556a boards and remove fallback board
This changes board info to match the Wiki
http://wiki.openwrt.org/toh/huawei/hg556a, removes the no longer needed
fallback board and fixes HG556 Ralink eeprom extraction.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: rename partitions instead]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42206
2014-08-18 21:50:29 +00:00
Hauke Mehrtens 09739f8ba5 brcm47xx: image: build alternative TRX using less optimized LZMA
There is a group of devices that lzma-loader doesn't work with. They
simply hang at "Starting program at 0x80001000" which is really hard to
debug and we didn't find any solution for this for years.

Broadcom doesn't use lzma-loader on these devices anyway. They decided
to drop lzma-loader and use less optimal LZMA compression that can be
handled by CFE itself (it doesn't use dictionary).

So support these devices we will need kernel compressed with different
parameters and trx without a loader.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42205
2014-08-18 21:00:55 +00:00
Hauke Mehrtens 32b3f9cdc6 brcm47xx/bcm53xx: improve description
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42204
2014-08-18 20:29:26 +00:00
Hauke Mehrtens 76866d42ac bcm53xx: remove kernel 3.10
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42203
2014-08-18 20:28:53 +00:00
Hauke Mehrtens ade7d7ba8c brcm47xx: update to kernel 3.14
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42202
2014-08-18 20:28:21 +00:00
John Crispin ff3ea02772 ramips: add omni plug leds
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42201
2014-08-18 16:09:21 +00:00
John Crispin d04cab8dfc ramips: Add support for Omnima MiniPlug
This patch adds support for the Omnima MiniPlug RT5350 based board, 8MB SPI flash

Signed-off-by: Ivan Ignjatic<ivan@omnima.co.uk>

SVN-Revision: 42200
2014-08-18 16:06:48 +00:00
John Crispin be6bbc7975 ramips: fix switch config for Edimax 3G-6200n
Switch in Edimax 3G-6200n also require full switch reset, not only vlan definitions. Tested on Edimax 3G-6200n.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 42194
2014-08-18 13:10:04 +00:00
John Crispin e5e1c03354 ar71xx: TL-WR1043N/ND v2: Fix MAC address of WMAC
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 42193
2014-08-18 13:10:00 +00:00
John Crispin 60bf96e3a0 ralink: clean up HAME profiles, remove unnecessary packages.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 42192
2014-08-18 13:09:46 +00:00
John Crispin a62e8bd145 ramips: add mpr-a1 to default profile
Add hame mpr-a1 to default ramips profile.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 42191
2014-08-18 13:09:43 +00:00
John Crispin bb9a23aca2 ramips: Hame: change LED name mpr-x -> hame
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 42190
2014-08-18 13:09:39 +00:00
John Crispin 5d9b1e7ec1 ar71xx: build factory image for EnGenius ESR900 and ESR1750
Signed-off-by: Forest Crossman <cyrozap@gmail.com>

SVN-Revision: 42189
2014-08-18 13:09:34 +00:00
John Crispin 12b73579e4 lantiq: update to 3.14
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42188
2014-08-18 13:09:30 +00:00
John Crispin 860e01d7c4 octeon: update to 3.14
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42187
2014-08-18 13:09:24 +00:00
John Crispin 0fc4383d69 ramips: make use of the new board detection layer
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42186
2014-08-18 13:09:20 +00:00
John Crispin 2c67682192 ar71xx: Fix 2.4G WiFi LED of the OpenMesh MR600 board
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 42184
2014-08-18 13:09:14 +00:00
John Crispin b796ff6ef3 lantiq: generate unique ARV7519RW22 firmware
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42183
2014-08-18 13:09:11 +00:00
John Crispin c2668207de lantiq: add support for xrx200 firmware depending on soc type
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42182
2014-08-18 13:09:08 +00:00
John Crispin db2e450ab5 lantiq: export soc type
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42181
2014-08-18 13:08:59 +00:00
John Crispin 5f71dbb005 lantiq: improve ARV7519RW22 support
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42180
2014-08-18 13:08:56 +00:00
John Crispin 3a9752bbd2 ramips: add a workaround to fix failsafe on RT5350
Due to TCP connections not working when VLAN is disabled, this is
needed to get failsafe functional.

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 42179
2014-08-18 13:08:52 +00:00
John Crispin f80312613d ramips: enable additional GPIOs on HAME MPR-A1
According to the pcb tracing results[1] by anton.rad[2] MPR-A1s expose
6 unused GPIOs, only one of them working as configured in the current
DTS. This patch enables GPIO22-26.

Tested on hardware.

[1] http://i.imgur.com/kHVW2Ox.jpg
[2] https://forum.openwrt.org/viewtopic.php?pid=222698#p222698

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 42178
2014-08-18 13:08:48 +00:00
John Crispin 340f87a20f ar71xx: changed the EnGenius ESR900 mtdparts to match that of the ESR1750 since they have the same flash layout
Signed-off-by: Forest Crossman <cyrozap@gmail.com>

SVN-Revision: 42177
2014-08-18 13:08:45 +00:00
John Crispin bf1e92f526 ralink: add back the gpio_export_named() patch for 3.14
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42176
2014-08-18 13:08:33 +00:00
Florian Fainelli 4147bca9ac adm8668: revert changeset 34554
The conversion was not 100% correct and leads to u-boot failing to
verify the CRC, revert that change for now.

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42170
2014-08-16 18:09:31 +00:00
Florian Fainelli 21fde478d9 ar7: remove 972-cpmac_fixup patch
This patch is causing more harm than good on most AR7 routers out there,
better have no manageable switch rather than no ethernet connection, at
least for now.

Fixes #16523, #5927

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 42168
2014-08-16 17:32:46 +00:00
Hauke Mehrtens ba0b904d0b brcm47xx: image: update list of Netgear WNR* firmwares
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42165
2014-08-14 21:22:17 +00:00
Hauke Mehrtens 254b4df66f brcm47xx: fix brcm47xx.legacy build
we should check for ssb here.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42164
2014-08-14 21:21:27 +00:00
Luka Perkov 24696a06ad imx6: update kernel config
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42149
2014-08-11 20:35:15 +00:00
Luka Perkov fa8e8d262e imx6: kernel: add GW5520 support
The GW5520 is a small form-factor single-board computer with the following
features:
 * 70x100mm form-factor
 * IMX6DL 800MHz SoC (IMX6Q optional)
 * 512MB 32bit DDR3 SDRAM (up to 2GB optional)
 * 256MB NAND FLASH (up to 2GB optional)
 * Gateworks System Controller
 * 2x front-panel Intel i210 GbE adapters with passive PoE support
 * 2x MiniPCIe sockets with USB support
 * 2x front-panel USB
 * 1x rear-panel full-size HDMI connector
 * 1x front-panel bi-color user LED
 * 1x front-panel user pushbutton
 * 1x rear-panel barrel jack for power
 * 1x Application connector with:
  * 2x TTL level UARTs
  * 10x TTL level Digital IO

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 42148
2014-08-11 20:35:13 +00:00
Luka Perkov dcacd65281 imx6: kernel: add GW16083 Ethernet Expansion Mezzanine support
The GW16083 Ethernet Expansion Mezzanine adds the following to supported
Gateworks baseboards:
 * 7-port Ethernet Switch
  * 4x RJ45 ports (ENET1-4) supporing 802.11af/at PoE (with optional PoE module)
  * 2x RJ45 ports or SFP module (ENET5-6) (auto-selected)

This series adds support for a phy driver that adds support for ENET5/ENET6
PHY adding initialization for those PHY's and a polling mechanism that detects
SFP insertion and configuration.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 42147
2014-08-11 20:35:10 +00:00
Luka Perkov 9d826428b7 imx6: kernel: add GW16082 miniPCI Expansion Mezzanine support
The GW16082 miniPCI Expansion Mezzanine has the INTA/B/C/D IRQ's reversed
from the PCI standard. This will soon be resolved in the bootloader via
devicetree, but in the meantime this will work around the issue.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 42146
2014-08-11 20:35:06 +00:00
Luka Perkov e47c4d7014 imx6: kernel: fix occasional link failure
Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 42145
2014-08-11 20:35:04 +00:00
Luka Perkov fe5d39d66c imx6: kernel: backport an upstream pci hang fix
Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 42144
2014-08-11 20:35:02 +00:00
Hauke Mehrtens 3c3b3dd41d bcm53xx: add b43 wifi support
Now it is possible to use b43 wifi.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42143
2014-08-11 20:25:26 +00:00
Hauke Mehrtens 1d14e7ef1b bcm53xx: remove BCM4360 from PCI ids
bcma does not support this card and b43 hangs when probing this card.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42142
2014-08-11 20:24:45 +00:00
Imre Kaloz ecba34a3ee add support for the NC-LINK SMART-300
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 42130
2014-08-11 11:44:51 +00:00
Jonas Gorski 43029544e2 brcm63xx: remove now obsolete board fixup code
Now that we migrated all users to dtb based detection, we can drop the
board fixup code.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42129
2014-08-11 11:37:26 +00:00
Jonas Gorski 74ec41ef59 brcm63xx: use dtb board detection for neufbox 4
This splits up neufbox 4 for now into two images, one for each OEM.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42128
2014-08-11 11:37:21 +00:00
Jonas Gorski 862f7fccb0 brcm63xx: use dtb board detection for NB6
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42127
2014-08-11 11:37:17 +00:00
Jonas Gorski 52b0935efe brcm63xx: use dtb board detection for HW556
This requires individual images for each board version for now.
Linux partition was shrunk to ensure writing thewrong image won't
erase wifi calibration data.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42126
2014-08-11 11:37:14 +00:00
Jonas Gorski 0aa242fe20 brcm63xx: replace CFEFIXUP usage with dtb based detection
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42125
2014-08-11 11:37:09 +00:00
Jonas Gorski f22bab1017 brcm63xx: move bcm96328avng to dtb detection
Use appended dtb for board detection for bcm96328avng.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42124
2014-08-11 11:37:04 +00:00
Jonas Gorski 9c6287d6a1 brcm63xx: add support for registering parallel flash through dtb
Add the required nodes to the dtsi files and code to prevent double
registration from the board support code.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42123
2014-08-11 11:37:01 +00:00
Jonas Gorski 79057c7255 brcm63xx: add helpers for building cfe images with dtb
Add a helper for building images with dtb appended kernels.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42122
2014-08-11 11:36:59 +00:00
Jonas Gorski aa572fccb5 brcm63xx: add support for attaching dtbs to lzma kernels
In preparation for switching to dtb based board identification, add
support for building lzma-loader and lzma cfe kernels with dtb
appended.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42121
2014-08-11 11:36:55 +00:00
Jonas Gorski 0343c0288e brcm63xx: add empty dtsi files for each of the supported SoCs
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42120
2014-08-11 11:36:53 +00:00
Jonas Gorski de8e3f2f86 brcm63xx: add and enable support for loading an appended dtb
Allow appending a dtb blob to the binary and use it for identifying the
board. Fall back to nvram based identification in case of no dtb passed.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42119
2014-08-11 11:36:48 +00:00
Jonas Gorski b61f57a5c7 brcm63xx: correctly export fallback sprom for brcm-wl
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42118
2014-08-11 11:36:41 +00:00
Jonas Gorski 97d0ed4faa brcm63xx: make board patch context less ambiguous
Make it less likely for quilt/patch to put boards into the "wrong"
section.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42117
2014-08-11 11:36:38 +00:00
Jonas Gorski a06013e9b7 brcm63xx: fix board patches offsets
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo fix 553-boards_probe_switch.patch]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42116
2014-08-11 11:36:30 +00:00
Luka Perkov a7840a0306 kernel: 3.14: refresh patches
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42113
2014-08-11 09:21:05 +00:00
Jonas Gorski 48318b52af brcm63xx: Add fallback sprom for A4001N
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42110
2014-08-10 12:22:15 +00:00
Jonas Gorski f30102c6c2 brcm63xx: Add fallback sprom for HG520v
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42109
2014-08-10 12:22:12 +00:00
Jonas Gorski e07dc84b24 brcm63xx: Add fallback sprom for P870HW-51a
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42108
2014-08-10 12:22:10 +00:00
Jonas Gorski 568a15adb3 brcm63xx: Add fallback sprom for VR-3025un
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42107
2014-08-10 12:22:08 +00:00
Jonas Gorski d3af37fdfb brcm63xx: Add fallback sprom for VR-3025u
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42106
2014-08-10 12:22:05 +00:00
Jonas Gorski 6eb9375da4 brcm63xx: Add fallback sprom for WAP-5813n
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42105
2014-08-10 12:22:02 +00:00
Jonas Gorski 061f738087 brcm63xx: Add fallback sprom for AR-5381u
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42104
2014-08-10 12:21:59 +00:00
Jonas Gorski 23df30ca4a brcm63xx: Add fallback sprom for AR-5387un
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42103
2014-08-10 12:21:55 +00:00
Jonas Gorski d1f731866b brcm63xx: Add fallback sprom for A4001N1
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42102
2014-08-10 12:21:52 +00:00
Jonas Gorski 312a7f9883 brcm63xx: Add fallback sprom for CT6373
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42101
2014-08-10 12:21:48 +00:00
Jonas Gorski 8240f6ad54 brcm63xx: Add fallback sprom for CT5365
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42100
2014-08-10 12:21:44 +00:00
Jonas Gorski a299702df0 brcm63xx: Add fallback sprom for CT5361_CT5621
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42099
2014-08-10 12:21:39 +00:00
Jonas Gorski a166e05188 brcm63xx: Add fallback sprom for Huawei HG553
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42098
2014-08-10 12:21:34 +00:00
Jonas Gorski 02e78b9bd8 brcm63xx: Fix fallback sprom il0mac
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 42097
2014-08-10 12:21:30 +00:00
Jo-Philipp Wich 0cf7cba67b netfilter: consider reply direction on selective flushing
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 42095
2014-08-10 10:15:22 +00:00
Jo-Philipp Wich f1b40f9304 netfilter: fix calls to nf_ct_iterate_cleanup() with Linux >= 3.13
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 42093
2014-08-10 09:21:14 +00:00
Jo-Philipp Wich 56be9f4a9a netfilter: support /proc conntrack flushing of specific ip addresses
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 42092
2014-08-09 14:36:10 +00:00
Hauke Mehrtens 47bab2b654 brcm47xx: fix reboot problem on BCM4705/BCM4785
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.

Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42088
2014-08-08 23:10:16 +00:00
Hauke Mehrtens 81c2466381 brcm47xx: fix reboot problem on BCM4705/BCM4785
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.

Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42083
2014-08-08 22:52:28 +00:00
Luka Perkov 97f26cad16 imx6: update upstream patch
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42081
2014-08-08 16:11:57 +00:00
Luka Perkov 7116b091eb kirkwood: drop 3.10 support
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42077
2014-08-08 13:55:30 +00:00
Luka Perkov f767d83b67 kirkwood: switch to 3.14
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42076
2014-08-08 13:55:29 +00:00
Luka Perkov c84876702b imx6: drop 3.10 support
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42075
2014-08-08 13:38:31 +00:00
Luka Perkov 4c2c390a23 imx6: switch to 3.14
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42074
2014-08-08 13:38:30 +00:00
Luka Perkov 60fe58100c imx6: update upstream patches
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42073
2014-08-08 13:38:29 +00:00
Luka Perkov d5f94a4122 imx6: backport IMX6DL DVFS support from 3.15
This allows dynamic voltage and frequency scaling to work for IMX6DL CPU's.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 42072
2014-08-08 13:38:27 +00:00
Luka Perkov 2b6d364a2d imx6: drop ventana kernel/rootfs hack
In r41578 this was added in order to make default images bootable for the BB
release. We need more generic approach for this.

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42071
2014-08-08 13:38:25 +00:00
Luka Perkov dd8d729096 kernel: update 3.14 to 3.14.16
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 42070
2014-08-08 13:38:22 +00:00
Hauke Mehrtens c371e6de02 brcm47xx: activate high mem for mips74k in the config
It is still not working.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 42054
2014-08-07 20:22:00 +00:00
Hauke Mehrtens 4ec288bfa4 brcm47xx: 3.14: backport MIPS patches for early HIGHMEM support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42053
2014-08-07 20:21:11 +00:00
Hauke Mehrtens dc38211cff brcm47xx: 3.10: backport MIPS patches for early HIGHMEM support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 42052
2014-08-07 20:20:38 +00:00
Felix Fietkau 053a3a4aaf kernel: add a patch to allow disabling processing of the netfilter "filter" table for established connection packets
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42046
2014-08-07 18:59:22 +00:00
Felix Fietkau 3e64341eac kernel: improve ipv4 netfilter optimization patch
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42045
2014-08-07 18:59:18 +00:00
Felix Fietkau ad876993d3 ar71xx: port missing ath79 machine entry for wndr3700 v4 to 3.14
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42044
2014-08-07 18:59:15 +00:00
John Crispin bc67bd2295 ralink: add 3.14 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42040
2014-08-07 14:41:19 +00:00
Felix Fietkau e41a0cafff ar71xx: add linux 3.14 support
Signed-off-by: Zhao, Gang <gang.zhao.42@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42038
2014-08-07 12:40:53 +00:00
Felix Fietkau f75f9606ad kernel: add a few more generic config symbols for 3.14
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42037
2014-08-07 12:40:47 +00:00
John Crispin 997ca19fd2 ralink: revert r37163
https://dev.openwrt.org/ticket/17071

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42036
2014-08-07 12:38:20 +00:00
John Crispin d8833ce163 octeon: add missing gpio_to_irq()
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42028
2014-08-07 09:54:07 +00:00
Steven Barth e7be51a0fd ar71xx: Add support for the WNDR3800CH
Apparently this is a fairly common refurb unit of the 3800 series now,
with merely the recognition string changed in the boot loader.

Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>

SVN-Revision: 42023
2014-08-07 05:14:26 +00:00
Jo-Philipp Wich a720dd209f build: introduce per feed repository support
This changeset implements a new menuconfig option to generate separate
repositories for each enabled package feed instead of one monolithic one.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 42002
2014-08-05 11:24:24 +00:00
Felix Fietkau 30ec58a217 atheros: switch kernel version to 3.14
After several tests, 3.14 kernel seems run fine.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41997
2014-08-04 20:54:57 +00:00
Felix Fietkau 930c0c24a7 atheros: add 3.14 configuration
Created on basis of 3.10 config. Remove few obsolete symbols and add new
upstream symbols. New symbols left in its default state.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41996
2014-08-04 20:54:53 +00:00
Felix Fietkau 5b9d4fd80a atheros: copy 3.10 patches to 3.14 and refresh them
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41995
2014-08-04 20:54:49 +00:00
Felix Fietkau 005f8ed563 atheros: refresh config-3.10
Refresh 3.10 kernel configuration, particulary correct AR2315_WDT symbol
position.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41994
2014-08-04 20:54:39 +00:00
Felix Fietkau b855faecc0 ar71xx: update Carambola2 platform data
Change list:
 * Remove button info on GPIO12, there is no button there.
 * Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.

Tested building for carambola2 target.

Signed-off-by: Mantas Pucka <mantas@8devices.com>

SVN-Revision: 41993
2014-08-04 14:46:52 +00:00
Felix Fietkau e6083fc8b1 kernel/3.1{3, 4}: fix IFF_NO_IP_ALIGN flag location
Fix IFF_NO_IP_ALIGN location which is collide with new netdev private flag
IFF_MACVLAN.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41992
2014-08-04 06:15:14 +00:00
John Crispin 17b8d9c976 ramips: add profile for easyacc wizard8800
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41986
2014-08-03 14:31:18 +00:00
John Crispin 058a5c85ef firmware-utils: made mkdir615h1 work for all Senao-produced devices as mksenaofw and cleaned up some of its formatting
Signed-off-by: Forest Crossman <cyrozap@gmail.com>

SVN-Revision: 41962
2014-08-03 11:13:58 +00:00
John Crispin 04e4ff282a ramips:support Lenovo AC1200 Wireless router
Lenovo AC1200 series has two types, Y1 and Y1S.
Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port.

Signed-off-by: Lintel <lintel.huang@gmail.com>

SVN-Revision: 41961
2014-08-03 11:13:52 +00:00
Felix Fietkau fe295cd178 kernel: when using --gc-sections, add --sort-section=name to get a more stable sorting order
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41951
2014-08-02 18:50:55 +00:00
Felix Fietkau 428539a3a2 kernel: add a small xfrm related performance optimization
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41950
2014-08-02 18:50:50 +00:00
Zoltan Herpai 06fdad1c12 mxs: - bump target to 3.14.14 - update dcp module
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 41949
2014-08-02 11:29:11 +00:00
Zoltan Herpai 15facdb2fa mxs: add 3.14 config and patches
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 41948
2014-08-02 11:20:01 +00:00
Zoltan Herpai 639a1f375b mxs: remote 3.12 patches and configs
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 41947
2014-08-02 11:18:00 +00:00
Jo-Philipp Wich baa7c211f5 netfilter: introduce xt_id match
This commit implements a new netfilter match "xt_id" which can be used to
attach unsigned 32bit IDs to iptables rules.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 41945
2014-08-01 22:49:47 +00:00
Jonas Gorski 930e3e7ca3 brcm63xx: add preliminary support for D-Link DSL-2751B E1
Mostly works except for USB led. Flashing not tested yet. Mostly
as an example for the sprom fixup code.

Fixup values taken from GPL tarball by comparing bcm43217_map.c
with the struct in sprom.c.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41944
2014-08-01 21:56:46 +00:00
Jonas Gorski 76746026b3 brcm63xx: rework fallback sprom support
Rework fallback sprom support by providing different sproms for
different chips. Also make it optional to use.

This likely causes sprom fallback support to break on a few boards.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41942
2014-08-01 21:56:38 +00:00
Jonas Gorski faa51b307c brcm63xx: switch to 3.14
Now that BB is branched off, we can now switch to 3.14 and start
breaking stuff again.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41941
2014-08-01 21:56:35 +00:00
Jonas Gorski 701e2a38fe brcm63xx: add working lzma-loader and use it for initramfs
Add a working lzma loader and use it for generating initramfs kernels
to allow easily netbooting elf kernels on devices with a 4 MiB CFE
size limit.

Based on ar71xx's lzma-loader.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41940
2014-08-01 21:56:31 +00:00
John Crispin 21845cb45d ramips: Add support for VoCore
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 41939
2014-08-01 20:51:24 +00:00
John Crispin 7d9bac5247 ramips: Add support for SPI_CS1 pinmux
This patch adds support for setting SPI_CS1 as Chip Select, Watchdog reset output and GPIO#27.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 41938
2014-08-01 20:51:14 +00:00
John Crispin 9efd7ebd34 ramips: add support for easyacc wizard8800
Signed-off-by: Sebastian Wendel <s.wendel@sourceindex.de>

SVN-Revision: 41936
2014-08-01 11:19:50 +00:00
John Crispin c6674722b9 ramips: Fix LEDs on the Kingston MLW221
LED Fix up for the Kingston Mobilelite Wireless (MLW-221)

http://wiki.openwrt.org/toh/kingston/mlw221

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 41933
2014-08-01 11:19:39 +00:00
John Crispin e7ec79821a ar71xx: oolite: the buttons are not active_low
this caused factory resets when reboot was pressed

Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41932
2014-08-01 11:19:34 +00:00
John Crispin 6ce44430c9 ar71xx: add RTC feature flag to ar71xx/nand
without this the build for NBG6716 fails due to missing packages

https://dev.openwrt.org/ticket/17325

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41930
2014-08-01 10:32:55 +00:00
Felix Fietkau 8dac6739f8 cns3xxx: add myself as maintainer
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41928
2014-08-01 09:23:50 +00:00
Felix Fietkau 2d5de51451 cns3xxx: fix building initramfs and non-initramfs together
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41922
2014-08-01 07:10:00 +00:00
Felix Fietkau 3c7cd63b72 cns3xxx: update to linux 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41917
2014-07-31 23:40:49 +00:00
Felix Fietkau 6944689e96 orion: fix 3.10 kernel minor version
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41916
2014-07-31 23:40:44 +00:00
Felix Fietkau 0426643bd5 cns3xxx: fix initramfs build
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41915
2014-07-31 23:40:40 +00:00
Hauke Mehrtens 69c403c234 bcm53xx: update to kernel 3.14
Use kernel 3.14 by default and refresh the patches

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41913
2014-07-31 21:44:41 +00:00
Hauke Mehrtens 350765676e bcm53xx: add restart support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41912
2014-07-31 21:43:40 +00:00
Hauke Mehrtens f7b3b7db7d brcm47xx: 3.14: update MIPS patches with versions sent upstream
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41911
2014-07-31 21:42:59 +00:00
Hauke Mehrtens 3a82681e4f brcm47xx: 3.10: update MIPS patches with versions sent upstream
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41910
2014-07-31 21:40:38 +00:00
Hauke Mehrtens 2b32939040 kernel: refresh patches
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41909
2014-07-31 21:33:58 +00:00
Hauke Mehrtens b1df24f00e kernel: update bcma to version master-2014-07-29-1
This is a backport of bcma from wireless-tesing/master tag master-2014-07-29-1.

For kernel < 3.10 this only adds the header changes needed by more
recent b43 versions.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41899
2014-07-30 18:54:10 +00:00
Luka Perkov f548b18353 kernel: update 3.14 to 3.14.14
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41898
2014-07-30 15:44:44 +00:00
Felix Fietkau 980e9b5fc2 atheros: remove linux 3.8 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41874
2014-07-29 10:23:59 +00:00
Jonas Gorski b723119385 brcm63xx: replace nvram_buf with a properly initialized array
Use an empty nvram_header to tell wl that there is no nvram buf.
wl else might try to allocate huge amount of memory because the
bcm63xx's nvram does not match the expected structure and contains
random values.

Fixes the following warning on load of wl:

[    9.152000] WARNING: at mm/slab_common.c:377 kmalloc_slab+0x4c/0xc0()
[    9.160000] Modules linked in: wl(P+) wl_glue ipv6 gpio_keys_polled input_polldev button_hotplug input_core
[    9.168000] CPU: 0 PID: 366 Comm: kmodloader Tainted: P             3.10.49 #1
[    9.176000] Stack : 00000000 00000000 00000000 00000000 8034b77a 00000042 81ac9af0 c02e0000
[    9.176000]    8028bf70 802df31b 0000016e 8034af28 81ac9af0 c02e0000 c02e0000 81b39810
[    9.176000]    0000002d 8002c9d4 00000003 8002a3c8 802937a0 c02e0000 8028e528 81ab398c
[    9.176000]    00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    9.176000]    00000000 00000000 00000000 00000000 00000000 00000000 00000000 81ab3918
[    9.176000]    ...
[    9.212000] Call Trace:
[    9.216000] [<800224b8>] show_stack+0x48/0x70
[    9.220000] [<8002a538>] warn_slowpath_common+0x78/0xa8
[    9.224000] [<8002a5f0>] warn_slowpath_null+0x18/0x24
[    9.228000] [<8008145c>] kmalloc_slab+0x4c/0xc0
[    9.236000] [<80097258>] __kmalloc+0x20/0x10c
[    9.240000] [<80e23b90>] osl_malloc+0x24/0x6c [wl]
[    9.244000] [<80e15288>] nvram_init+0x54/0x164 [wl]
[    9.252000] [<80e08668>] si_pci_fixcfg+0x60c/0x9e8 [wl]
[    9.256000]
[    9.260000] ---[ end trace b5c4dbb046cf3c83 ]---

Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41861
2014-07-28 15:31:37 +00:00
John Crispin c21a20cd78 lantiq: fix dgn3500 and td8970 wifi
ath9k failed to come up due to a bad mac addr

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41860
2014-07-28 15:26:41 +00:00
John Crispin 6fb04ff871 ramips: correct typo ubsphy -> usbphy
This appears to be a typo.

Signed-off-by: Russell Senior <russell@personaltelco.net>

SVN-Revision: 41859
2014-07-28 15:26:36 +00:00
John Crispin 6f6dc62ca2 ramips: fix mode switch gpio for AsiaRF AWM eval board
Fix a typo: gpio 21 is already used for the WPS led.  Gpio 20 is the
right one (tested) for the mode switch.  Confirmed that
/sys/kernel/debug/gpio state followed the position of the switch.

Signed-off-by: Russell Senior <russell@personaltelco.net>

SVN-Revision: 41858
2014-07-28 15:26:32 +00:00
John Crispin 636f2b83e6 ramips: add ethernet macaddr to dts for AWM003-EVB
Follows the pattern of http://patchwork.openwrt.org/patch/5970/

Signed-off-by: Russell Senior <russell@personaltelco.net>

SVN-Revision: 41857
2014-07-28 15:26:23 +00:00
Jonas Gorski 042fb8eb57 brcm63xx: 3.14: fix ath9k_pci_fixup
Since kernel commit 928bea964827 ("PCI: Delay enabling bridges until
they're needed"), pci fixups are run with bridges (e.g. the pcie port)
disabled.

This causses hangs when ath9k_pci_fixup tries to manually enable the
device to apply the register fixups.

Fix this by enabling any parent bridges before trying to access the
device itself.

Fixes boot on DSL-274XB rev F1.

Reported-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41856
2014-07-28 11:12:25 +00:00
John Crispin 3836d40a8a lantiq: fix dgn3500 ethernet
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41854
2014-07-28 08:06:40 +00:00
Jonas Gorski 1cb1041c55 brcm63xx: Add support for ADB P.DG A4001N
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41852
2014-07-27 17:44:59 +00:00
Jonas Gorski 3209fb968e brcm63xx: Add support for Huawei HG520v
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41851
2014-07-27 17:44:56 +00:00
Jonas Gorski c27cb6e0fd brcm63xx: Add support for ZyXEL P870HW-51a v2
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41850
2014-07-27 17:44:53 +00:00
Jonas Gorski b26139eb3f brcm63xx: Add support for Comtrend VR-3025un
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41848
2014-07-27 17:44:48 +00:00
Jonas Gorski a669d2c528 brcm63xx: Add support for Comtrend VR-3025u
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41847
2014-07-27 17:44:45 +00:00
John Crispin 8c57e2d888 octeon: enable usb and gpio
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41846
2014-07-27 14:52:18 +00:00
John Crispin 43ee42bd05 octeon: add gpio driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41845
2014-07-27 14:52:12 +00:00
John Crispin 13445d2576 octeon: add detection for edgerouter and edgerouter-pro
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41844
2014-07-27 14:52:07 +00:00
John Crispin 694295e7be octeon: fix usb support on edge router pro
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41842
2014-07-26 20:36:32 +00:00
John Crispin 5b4abf87d7 ramips: add support for Kingston MLW221
This patch adds support for the Kingston Mobilelite Wireless (MLW-221)

http://wiki.openwrt.org/toh/kingston/mlw221

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 41841
2014-07-26 20:36:22 +00:00
John Crispin b77e92e020 ramips: ethernet mac cleanup
Compile tested all subtargets and profiles.
Unfortunately I don't own any board affected by these changes, so no run tests.

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41839
2014-07-26 20:36:09 +00:00
John Crispin 443aee86bf ramips: fix vlan configuration for asiarf avm003
The earlier r41797 change was missing this part, to enable the right
vlan configuration.

Signed-off-by: Russell Senior <russell@personaltelco.net>

SVN-Revision: 41838
2014-07-26 20:36:01 +00:00
John Crispin 08fb5fb326 ramips: fix sysupgrade for asiarf awm003
Since the earlier r41797 change, the board_name for awm003 has been
miscalculated, and sysupgrade has been broken.  This seems to fix it.

Signed-off-by: Russell Senior <russell@personaltelco.net>

SVN-Revision: 41837
2014-07-26 20:35:46 +00:00
Hauke Mehrtens 7a3b3b9d73 brcm47xx: don't create named switch_vlan sections
It doesn't seem to be used anywhere, it's incompatible with other
targets and can be confusing. People may think they need to update
section name every time they change VLAN ID (well, even I was doing
that).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41835
2014-07-26 12:33:48 +00:00
Hauke Mehrtens 009e36806b kernel: remove kernel 3.6
kernel 3.6 is not used by any target any more, remove it.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41834
2014-07-26 12:23:56 +00:00
John Crispin caa671d873 imagebuilder: fix typo that copied grub to the wrong folder
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41824
2014-07-24 15:46:12 +00:00
Felix Fietkau ea76a0b78e kernel: annotate bridge multicast backport patch with upstream commits
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41819
2014-07-24 09:19:37 +00:00
Felix Fietkau dd7650f67c kernel: backport upstream bridge multicast snooping fixes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41817
2014-07-24 09:12:59 +00:00
Imre Kaloz dc628f2e08 add support for the archer c5
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41814
2014-07-23 12:47:25 +00:00
Imre Kaloz 039fe23f8e refresh patches
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41812
2014-07-23 11:46:42 +00:00
John Crispin 0b5b8de818 ramips: fix gpio mapping on MZK-750DHP
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41811
2014-07-23 07:49:54 +00:00
John Crispin e5d4e5dee3 ramips: fix missing inclusion of system.sh for mtd_get_mac_binary and friends.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 41810
2014-07-23 07:49:50 +00:00
John Crispin 3bb8589787 ar71xx: fix LED configuration for HiWiFi-HC6361.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 41809
2014-07-23 07:46:07 +00:00
Hauke Mehrtens 0d3690a202 kernel: update bcma and ssb to version master-2014-07-22
This is a backport of bcma and ssb from wireless-tesing/master tag
master-2014-07-22.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41804
2014-07-22 21:40:41 +00:00
John Crispin 2c356c4bb7 ramips: add a profile for AWM003
same as AWM002 but with 64mb RAM

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41797
2014-07-22 09:58:21 +00:00
John Crispin 4f5081c911 ar71xx: fix WAN MAC setup on dir-825-c1
Changeset 38690 broke the WAN MAC setup. Here's the fix.

Signed-off-by: Sebastian Kemper <sebastian_ml <at> gmx.net>

SVN-Revision: 41795
2014-07-21 19:26:54 +00:00
John Crispin 6dd7875412 ar71xx: Register reset button on UBNT AirGW
The airGateway has a reset button connected to GPIO 12, so we should use it.

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>

SVN-Revision: 41794
2014-07-21 19:26:50 +00:00
John Crispin a440524f85 ar71xx: Fix GL.iNet WLAN LED
LED script expects WLAN LED to be "gl-connect:red:wlan".

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 41793
2014-07-21 19:26:46 +00:00
John Crispin 8295b1f7f2 target/linux/*/image/Makefile: eliminate more LINUX_DIR users
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41792
2014-07-21 18:42:11 +00:00
John Crispin 7d8f187201 target/linux/*/image/Makefile: use new dts path variable
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41791
2014-07-21 18:42:06 +00:00
John Crispin 941dab02d5 imagebuilder: copy dts folder
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41790
2014-07-21 18:42:00 +00:00
John Crispin eae9b2541a ar71xx: split wndr4300 and wndr3700v4 into 2 seperate mips machines
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41788
2014-07-21 18:41:52 +00:00
John Crispin 2b48ee80f9 kernel: refresh 3.10 patches
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41777
2014-07-20 17:31:15 +00:00
John Crispin ba63338d3f kernel: update to 3.10.49 Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41776
2014-07-20 17:31:11 +00:00
John Crispin 34c9bc0596 ar71xx: create profile and build image for the OpenMesh OM5P board
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 41775
2014-07-20 17:31:05 +00:00
John Crispin f68665ac1d ar71xx: enable sysupgrade for the OpenMesh OM5P
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 41772
2014-07-20 17:30:52 +00:00
John Crispin e50abb5d53 ar71xx: add user-space support for the OpenMesh OM5P
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 41770
2014-07-20 17:30:44 +00:00
John Crispin f424994cbc ar71xx: add kernel support for the OpenMesh OM5P board
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 41769
2014-07-20 17:30:32 +00:00
John Crispin 4d22954db0 ramips: fix mac address partitions on ASL-26555
ASL-26555 16MB: caldata is present on uboot-env and devdata, but the proper one seems to be the devdata, since mac address corresponds to Amper, the real manufacturer, meanwhile the caldata on  uboot-env corresponds to D-Link.
ASL-26555 8MB: caldata is only present on uboot-env, but its mac address corresponds to Alpha, the real manufacturer.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 41768
2014-07-20 17:30:28 +00:00
John Crispin 7388053ba3 ar71xx: add RB91x boards to uci-defaults 02_network
The default case in 02_network is inappropriate for the MikroTik RouterBOARD 91x boards because they do not have a WAN port, so don't bother setting the non-existent eth1 interface as the WAN port.

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>

SVN-Revision: 41767
2014-07-20 17:30:24 +00:00
John Crispin d19530c693 ar71xx: Add UBNT airGateway support
This patch adds support for the Ubiquiti Networks airGateway.

Based in part on code posted by David Hutchison <dhutchison@bluemesh.net> on openwrt-devel:
  https://lists.openwrt.org/pipermail/openwrt-devel/2013-December/023035.html

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>

SVN-Revision: 41766
2014-07-20 17:30:17 +00:00
Hauke Mehrtens e23f27b72d orion: Update kernel to 3.10.44
Update the kernel of the orion target to version 3.10.44.
Refresh orion config and patches to match the changes in the kernel

Tested on WRT350N-v2 device.

Signed-off-by: Maarten Bezemer <maarten.bezemer@gmail.com>
[run make kernel_oldconfig, fold a01-dt2-fixes-for-3.3.patch into dt2-setup.c,
 make dt2-setup.c compile, fix harddisk subprofile]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41765
2014-07-20 09:42:14 +00:00
Felix Fietkau c718d0b10c x86: remove the arbitrary limitation of vmware/virtualbox images to ext4, select TARGET_IMAGES_PAD instead
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41763
2014-07-20 08:18:50 +00:00
Imre Kaloz 7e2c4d5732 extract and fixup the board.bin on the archer
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41757
2014-07-19 13:20:14 +00:00
Hauke Mehrtens 6f6b8feae6 pxa: add support for kernel 3.10
This is compile tested only, please run test and report back.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41737
2014-07-18 20:45:49 +00:00
Hauke Mehrtens 5a331a91aa cobalt: add support for kernel 3.10
This is compile tested only, please run test and report back.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41736
2014-07-18 19:03:16 +00:00
Felix Fietkau 1d232f354a kernel: mtd: allow partial block erase
This fixes error erasing partial mtd partition which does not start on
eraseblock boundary and allows using fconfig to configure redboot on
devices such as the Gateworks Cambria.

Signed-off-by: Maciej Skrzypek <maciej.skrzypek@flytronic.pl>

SVN-Revision: 41733
2014-07-18 14:36:38 +00:00
Hauke Mehrtens 7435b628c6 brcm47xx: fix switch detection with kernel 3.14
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41706
2014-07-17 20:34:18 +00:00
Felix Fietkau daae0b7c93 kernel/3.1{3, 4}: fix AMD USB HDC wakeup quirk disabling
Declare inline placeholder when usb_hcd_amd_remote_wakeup_quirk() not
compiled due CONFIG_PCI_DISABLE_COMMON_QUIRKS.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41702
2014-07-17 16:44:04 +00:00
Felix Fietkau 5e0bd41bbe atheros: update macroses names
Use AR2315_ prefix for macroses specific to AR2315/AR2316/AR2317 chips,
use AR5312_ prefix for macroses specific to AR5312/AR2312/AR2313 chips,
and use AR231X_ prefix for common macroses.

This patch should not cause any functional changes, only make clear
which macros is common and which macros is specific.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41701
2014-07-17 16:36:55 +00:00
Felix Fietkau 04f3012fba atheros[uart]: pass only physical I/O mem address to 8250 driver
Pass only physical address to 8250 serial port driver and set flag to
remap I/O memory inside the driver. Also fix AR5312 UART base address
definition, which seems specified already mapped.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41700
2014-07-17 16:36:52 +00:00
Felix Fietkau e744878636 atheros[uart]: use 32-bit aligned I/O
Use 32-bit aligned I/O and update base UART address (remove +3 offset).

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41699
2014-07-17 16:36:49 +00:00
Felix Fietkau 572b532e6a atheros[ar231x-eth]: pass PHY I/O memory via device resources
Pass PHY I/O memory region via platform resources and remap them
unconditionally.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41698
2014-07-17 16:36:46 +00:00
Felix Fietkau 9041410017 atheros[ar231x-eth]: pass phys address of I/O memory via platform res
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41697
2014-07-17 16:36:43 +00:00
Felix Fietkau a145d0410b atheros: simplify gpiolib realization
Each SoCs generation has own independent gpiolib realization, so we
have no reason to keep these realizations in semiuniversal form.
Following modifications are made:
 * Remove valid_mask field
 * Remove ar231x_gpio_chip structure
 * Rename AR2315_GPIO_CR to AR2315_GPIO_DIR
 * Fix count of AR5312 GPIOs
 * Simplify gpio_chip methods realization

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41696
2014-07-17 16:36:39 +00:00
Felix Fietkau 82e4cde1ce atheros: use irq_set_chained_handler()
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41695
2014-07-17 16:36:36 +00:00
Felix Fietkau 0a785ebb7d atheros: simplify AR2315 misc IRQ (un)masking
Currently AR5312 misc IRQ numbers are used for AR2315+ chips, what cause
us to use switch-case to map IRQ number to ISR bit. Introduce AR2315
specific misc IRQs set and simplify interrupt (un)mask operation.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41694
2014-07-17 16:36:33 +00:00
Felix Fietkau d29b61b5f0 atheros: rename some interrupt control handlers
Rename interrupt control handlers to be consistent with operation names
and add IRQ chips names.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41693
2014-07-17 16:36:30 +00:00
Felix Fietkau fceb7f7045 atheros: move AR2315 misc IRQ dispatching to separate function
Align code with AR5312 realization.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41692
2014-07-17 16:36:26 +00:00
Felix Fietkau 5c030111a9 atheros: pass UART IRQ number via function argument
UART IRQ number could be different for different SoCs, so make them
configurable.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41691
2014-07-17 16:36:23 +00:00
Felix Fietkau e819113e2e atheros[ar231x-eth]: move driver to atheros subdirectory
Move driver code to respective vendor subdirectory and fix config
symbol name.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41690
2014-07-17 16:36:19 +00:00
Felix Fietkau 6be418e3e1 atheros[ar231x-eth]: update MAC and PHY reset method
Pass reset_set and reset_clear callback functions pointers via
platform_data instead of reset register address.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41689
2014-07-17 16:36:16 +00:00
Felix Fietkau 4f05d696ad atheros[ar2315-wdt]: update I/O handling
* Pass iomem and IRQ via platform device resources
 * Remap iomem and use iowrite32 accessor function

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41688
2014-07-17 16:36:13 +00:00
Felix Fietkau 5ea0cff89c atheros[ar2315-wdt]: update interrupt handling
Acknowledge watchdog interrupt in arch irq dispatcher and remove odd
watchdog enable call from probe function.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41687
2014-07-17 16:36:10 +00:00
Felix Fietkau d0f9972f1c atheros: use correct address space and pointer type for register access
Make sparse happy :)

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41686
2014-07-17 16:36:07 +00:00
Felix Fietkau 579481b4f5 atheros[ar2315-wdt]: rename config symbol
Rename config symbol to AR2315_WDT to avoid confusion with other Atheros
SoCs.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41685
2014-07-17 16:36:03 +00:00
Felix Fietkau 5e76534b23 atheros[ar2315-wdt]: update initialization
* update driver id to be consistent with other ar231x drivers
 * remove odd module_{init,exit}
 * add module metadata (description, name, etc.)

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41684
2014-07-17 16:35:59 +00:00
John Crispin f44d3f9980 ramips: soc wmac eeprom cleanup
Move eeprom extraction from scripts to dts files.
Additionally there are few other changes like:
- whitespace fixes
- add partition labels where needed
- BR6524N board doesn't exist (lost in translation?)
- fix Edimax 3g-6200nl model
- add wmac eeprom to dts for Asus RT-N14U board

Compile tested all subtargets and their profiles.
Run tested on:
- Asus RT-N15
- Asus RT-N14U
- Buffalo WHR-600D
- Argus ATP52B
- Sparklan WCR-150GN

Few problems noted:
- many boards didn't have wmac eeprom information defined at all
- several boards don't have any patitions defined (see FIXME comments in dts)

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41680
2014-07-17 10:55:31 +00:00
Hauke Mehrtens d8e47a92b1 ep93xx: add support for kernel 3.10
This is compile tested only, please run test and report back.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41679
2014-07-16 21:29:16 +00:00
Hauke Mehrtens d84579def5 kernel: add CONFIG_I2C_AU1550 config option
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41678
2014-07-16 20:45:20 +00:00
John Crispin 4beb468f11 lantiq: fix board_id/boardname for VGV7519
Signed-off-by: Eddi De Pieri <eddi@depieri.net>

SVN-Revision: 41672
2014-07-16 11:36:02 +00:00
Felix Fietkau 6c7de7abca au1000: remove linux 3.6 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41670
2014-07-16 06:55:19 +00:00
Hauke Mehrtens a36ca743d6 au1000: update to kernel 3.10.44
This was tested by Bruno Randolf on au1000 (MTX-1)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41669
2014-07-15 22:03:10 +00:00
Hauke Mehrtens 1636bc6704 brcm47xx: remove kmod-bgmac from profile
bgmac will be compiled into the kernel since r41594.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41667
2014-07-15 21:57:13 +00:00
Hauke Mehrtens f5955c2e6b brcm47xx: fix LEDs on WRT54GL 1.1
Ticket: #17062
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41666
2014-07-15 21:54:38 +00:00
Hauke Mehrtens 6f417d5b4b brcm47xx: fix special board handling for some devices
Some devices were renamed when converted from diag to in kernel board detection and it was not changed in netconfig. Devices not in the
kernel board detection are removed now.

This should close: #17111, #16968, #13202

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41663
2014-07-14 22:16:19 +00:00
Hauke Mehrtens 7dbea92a9c brcm47xx: improve board detection for some devices
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41662
2014-07-14 22:03:59 +00:00
Gabor Juhos 2adff1734f ar71xx: add profile and build image for the EnGenius EAP300 v2 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41661
2014-07-14 21:30:30 +00:00
Gabor Juhos 54206fb0ce ar71xx: add user-space support for the EnGenius EAP300 v2 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41659
2014-07-14 21:30:28 +00:00
Gabor Juhos aff3127956 ar71xx: add kernel support for the EnGenius EAP300 v2 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41658
2014-07-14 21:30:26 +00:00
John Crispin 85cacfd753 lantiq: vgv7519 add missing wps label to dts
Signed-off-by: Eddi De Pieri <eddi@depieri.net>

SVN-Revision: 41655
2014-07-14 18:43:02 +00:00
John Crispin 74db9511dc ramips: basic support for Planex MZK-750DHP
some gpios are still missing.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41654
2014-07-14 17:10:39 +00:00
John Crispin e33584f6b8 ramips: squelch mdio debugging info on rt2880 ethernet
Use pr_debug rather than pr_info since it is only relevant
for debugging.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 41653
2014-07-14 17:05:40 +00:00
Gabor Juhos 495aef39f4 ar71xx: add profile and build image for the Tube2H board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41652
2014-07-14 16:03:37 +00:00
Gabor Juhos f27f2fec4f ar71xx: add user-space support for the Tube2H board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41650
2014-07-14 16:03:35 +00:00
Gabor Juhos 51c892053a ar71xx: add kernel support for the Tube2H board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41649
2014-07-14 16:03:34 +00:00
Imre Kaloz d7ae7bae57 mark the default WRT1900AC image "factory"
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41648
2014-07-14 15:02:38 +00:00
Imre Kaloz 6f5a9debed handle sysupgrade tar files on the WRT1900AC
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41647
2014-07-14 15:00:36 +00:00
Gabor Juhos 907bd5345e ar71xx: fix ALFA NETWORK's name
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41643
2014-07-14 11:10:00 +00:00
Gabor Juhos fec2596282 ar71xx: add profile and build image for the EnGenius ESR900
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5715/
[juhosg: change subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41642
2014-07-14 10:25:53 +00:00
Gabor Juhos 50c554a475 ar71xx: add user-space support for the EnGenius ESR900
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5716/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41641
2014-07-14 10:25:51 +00:00
Gabor Juhos 0bec90b830 ar71xx: add kernel support for the EnGenius ESR900
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5714/
[juhosg:
  - drop nvram.c modifications,
  - create a separate kernel patch,
  - use ath79_setup_qca955x_eth_cfg helper,
  - merge esr900_{010,common}_setup functions,
  - statically init AR8327 pad configurations,
  - use pr_err instead of printk]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41640
2014-07-14 10:25:51 +00:00
John Crispin c8bde9da4a lantiq: detect board in preinit state
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41638
2014-07-14 07:38:52 +00:00
John Crispin e503eeb465 ar71xx: add support for nanostation m xw
SVN-Revision: 41636
2014-07-14 07:38:43 +00:00
John Crispin de5fd0a189 ar8216: add new phyid 0x004dd043 (ar8326)
Used in ubiquity nanostation xw boards

SVN-Revision: 41635
2014-07-14 07:38:39 +00:00
John Crispin 76ba6846a2 ramips: fix port mapping and extract wmac eeprom on ZBT-WA05 board
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41634
2014-07-14 07:38:32 +00:00
John Crispin 8c577d9fde ramips: extract mac address from flash on WHR-600D board
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41633
2014-07-14 07:38:28 +00:00
John Crispin 4af1b51ec3 ramips: extract default lan_mac from eth0
The default case of ramips_setup_macs() is useful when mtd-mac-address is defined in dts.
But lan_mac is not set by default, this results in lan and wan having the same mac.

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41632
2014-07-14 07:38:23 +00:00
Imre Kaloz 1d11ffa4f2 use the full boardname for the wrt1900ac image
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41631
2014-07-13 22:15:03 +00:00
Imre Kaloz 81d85a717a add sysupgrade support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41630
2014-07-13 22:12:56 +00:00
Imre Kaloz 88121f229c update wrt1900ac dts
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41629
2014-07-13 22:11:43 +00:00
Gabor Juhos 26b39cc580 ar71xx: use ath79_setup_qca955x_eth_cfg helper for QCA955x based boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41627
2014-07-13 19:44:00 +00:00
Gabor Juhos c4c25e741e ar71xx: add profile and build image for EnGenius ESR1750
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5840/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41626
2014-07-13 19:43:59 +00:00
Gabor Juhos 2d6542242a ar71xx: add user-space support for EnGenius ESR1750
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5840/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41625
2014-07-13 19:43:58 +00:00
Gabor Juhos 16d45d5531 ar71xx: add kernel support for EnGenius ESR1750
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5840/
[juhosg:
  - fix coding style in mach-esr1750.c,
  - rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41624
2014-07-13 19:43:57 +00:00
Gabor Juhos ee3dfafaf1 ar71xx: add a helper function for setting up ETH_CFG register on QCA955x
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5839/
[juhosg: fix coding style]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41623
2014-07-13 19:43:56 +00:00
Gabor Juhos a46c7d055c ar71xx: allow ath79_nvram_parse_mac_addr parsing mac with quotes
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5838/
[juhosg:
  - fix coding style,
  - check the first and the last character of the MAC string
    instead of using the strchr() function]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41622
2014-07-13 19:43:54 +00:00
Gabor Juhos a749d8163f ar71xx: add profile and build image for GL.iNet v1
Patch is based on http://patchwork.openwrt.org/patch/5273/.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5653/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41621
2014-07-13 18:21:09 +00:00
Gabor Juhos 6991725a1e ar71xx: add user-space support for GL.iNet v1
Patch is based on http://patchwork.openwrt.org/patch/5273/.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5652/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41619
2014-07-13 18:21:06 +00:00
Gabor Juhos 9801351c84 ar71xx: add kernel support for GL-Inet V1 boards/routers
The GL-Connect GL.iNet v1 router is basically a TP-Link TL-WR703N with
more DRAM/Flash, 2x Ethernet ports and console/GPIO header in the same
small form-factor:
<http://www.gl-inet.com/w/?lang=en>

Moreover, the manufacturer is promoting the OpenWrt usage to replace
the original firmware and proposing patches against both AA and trunk:
<http://www.gl-inet.com/w/?p=398&lang=en>

This is a clean up of the original manufacturer GPLv2 patch by alzhao,
proposed to the list by Mark Janssen.

Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5273/
[juhosg:
  - remove user-space and image generation support, will be included
    from other patches,
  - fix coding style and drop superfluous comment in mach-gl-inet.c,
  - rename and refresh kernel patch,
  - adjust subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41618
2014-07-13 18:21:04 +00:00
Gabor Juhos 0ffe21c792 ar71xx: Support for Mikrotik RB2011UiAS
The RB2011UiAS is almost exactly the same as the RB2011UAS, which is
already supported. Hardware-wise, it adds a passive power injector on
Eth10. Software-wise, Routerboot passes a different board name on the
kernel command line. Hence the need for a patch.

Not yet working:

* touchscreen: doesn't work on RB2011UAS either. The touchscreen itself
  seems to be driven by an ADS7843-compatible IC, but figuring out which
  GPIO pins it's connected to is work for the future.
* control of power injector: remains off. Probably also GPIO-controlled.

Signed-off-by: Soren Harward <stharward@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5841/
[juhosg: rename and refresh the kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41617
2014-07-13 16:25:58 +00:00
Gabor Juhos f089f0db34 ar71xx: select correct Kconfig symbol in the Mikrotik SXT Lite patch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41616
2014-07-13 16:25:57 +00:00
Gabor Juhos 68871def8d ar71xx: refresh patches
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41615
2014-07-13 16:25:56 +00:00
Gabor Juhos d0ad8c00b6 kernel: sort Kconfig options in kernel configs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41614
2014-07-13 16:25:54 +00:00
John Crispin 9e26031a88 ar71xx: add support for TP-LINK TL-WA860RE v1
New router/repeater from TP-LINK

- CPU: Atheros AR9341-DL3A (AP123)
- Flash: 4MB
- Ram: 32MB

Similar to TL-WA850RE.

Changes: rename file after r41596

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 41598
2014-07-13 10:03:41 +00:00
John Crispin 42a37b2a89 ar71xx: added support for TL-WA830RE V2
Corrected patch ath79 insted of auth79. Sorry.

Signed-off-by: Fredrik Jonson <fredrik@famjonson.se>

SVN-Revision: 41596
2014-07-13 07:12:22 +00:00
Hauke Mehrtens ba54356d49 brcm47xx: deactivate ssb and old phy code for new devices
This deactivates ssb and G-PHY code in b43 for the mips74k profile in
brcm47xx.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41594
2014-07-12 15:39:31 +00:00
Jonas Gorski 2b6403722b brcm63xx: update irq affinity code to latest version
Reduces code size a bit and sets affinity to boot cpu by default.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41591
2014-07-12 12:31:47 +00:00
Jonas Gorski ba9d2f397a brcm63xx: base-files: order board names alphabetically
Restore alphatetical order in uci-defaults scripts and brcm63xx.sh

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41590
2014-07-12 12:31:45 +00:00
Jonas Gorski 44e187fd66 brcm63xx: Use leds script for Huawei HG556a and improve profile
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41589
2014-07-12 12:31:43 +00:00
Jonas Gorski e5cadabb58 brcm63xx: Fix HW553 support
- adsl and lan leds are swapped.
- internetkey is labeled as hspa.
- enable status led and reset button for failsafe.
- use new leds script.
- fix switch configuration.
- remove enet0 from board_info.
- add profile.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41588
2014-07-12 12:31:39 +00:00
Jonas Gorski beb25f96eb brcm63xx: Use model name for Comtrend AR-5381u
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41587
2014-07-12 12:31:35 +00:00
Jonas Gorski c9b2e96909 brcm63xx: Use model name for Comtrend AR-5387un
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41586
2014-07-12 12:31:33 +00:00
Jonas Gorski aee666d8f9 brcm63xx: Use model name for ADB P.DG A4001N1
This patch also makes use of the new leds script.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41585
2014-07-12 12:31:30 +00:00
John Crispin ba3988fb16 ramips: add support for WR8305RT board
Signed-off-by: Jorge Vargas <jorge.vargas@sosvia.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41584
2014-07-12 06:54:03 +00:00
John Crispin 91e2f1e9a6 brcm2708: Use uci-defaults for network config
By using uci-defaults force_link is enabled, which fixes some link issues if ethernet cable isn't connected when LAN is initialized.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 41583
2014-07-12 06:50:21 +00:00
Luka Perkov a145a22f66 kernel: update 3.14 to 3.14.12
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41582
2014-07-11 13:28:44 +00:00
Luka Perkov 2bc22025dd kernel: remove 3.12 support since none of the targets is using it
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41581
2014-07-10 22:37:28 +00:00
John Crispin 68e8614009 imagebuilder: x86 fails to build inside the imagebuilder
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41580
2014-07-10 22:02:31 +00:00
John Crispin 03faf4618e ramips: add support for Zbtlink WA05 router
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41579
2014-07-10 22:02:28 +00:00
John Crispin f88fde9689 imx6: put kernel and dtb into rootfs by default
this will make the rc1 images boot with the default config.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41578
2014-07-10 22:02:24 +00:00
Felix Fietkau a17a58e310 ar8216: disable EEE by default on AR8327 to fix stability issues (#14597)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41577
2014-07-10 21:11:02 +00:00
Felix Fietkau f083ca9743 octeon: fix edgerouter pro ethernet device probe order
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41575
2014-07-10 20:44:03 +00:00
John Crispin 6134a3de30 target/linux/*: more dead package cleanups
found 2 more

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41574
2014-07-10 20:15:50 +00:00
Felix Fietkau 1b6dece9ea octeon: add basic board detection for UBNT EdgeRouter PRO
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41572
2014-07-10 20:14:54 +00:00
John Crispin 32e93efc73 target/linux/*: more dead package cleanups
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41571
2014-07-10 20:05:43 +00:00
Felix Fietkau 7b0ec8a5db octeon: backport a few upstream fixes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41568
2014-07-10 19:28:37 +00:00
John Crispin 332b4d556f lantiq: generate /tmp/sysinfo/lantiq_board_name if missing
Run lantiq_board_detect from lantiq_board_name and lantiq_board_model.

This was the one thing missing from r41474 for sysupgrade board
detection to work properly.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41567
2014-07-10 19:16:43 +00:00
John Crispin 03fef9a2d2 lantiq: enable SysupgradeNAND for BTHOMEHUBV2B
Enables SysupgradeNAND for BTHOMEHUBV2B.

Depends on the following patches:
http://patchwork.openwrt.org/patch/5817/
http://patchwork.openwrt.org/patch/5848/
http://patchwork.openwrt.org/patch/5851/

Many thanks everyone for your help the last couple of days.

Ben

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41566
2014-07-10 19:16:39 +00:00
John Crispin 4e35eef1d7 lantiq xway: disable gluebi and enable ubiblock
Disables gluebi and enables ubiblock on lantiq xway. Squashfs
images on nand use ubifs instead of jffs2 for the overlay.

I'll leave the equivalent patch for xrx200 to someone who has a
board to test.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41565
2014-07-10 19:16:35 +00:00
John Crispin f8f6678574 ar71xx: nbg6716: extract ath10k wifi board.bin
With help of this script the ath10k board.bin settings are loaded from
flash and saved to the ath10k firmware directory. The driver reads it
later in the boot process.

Signed-off-by: André Valentin <avalentin@marcant.net>

SVN-Revision: 41562
2014-07-10 19:16:23 +00:00
John Crispin 94802dca60 ralink: wpa does not exist, use wpad-mini instead
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41561
2014-07-10 19:16:19 +00:00
John Crispin 0f76f8a16e target/linux/*: kmod-fs-ext{2,3} RIP
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41560
2014-07-10 19:16:15 +00:00
Imre Kaloz 811d1682b8 enable handling of the wan led on the WRT1900AC
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41555
2014-07-10 10:19:06 +00:00
Felix Fietkau f98306bef4 kernel: revert an upstream linux-stable commit that is causing usb regressions on some brcm47xx and ar71xx devices
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41554
2014-07-09 10:11:23 +00:00
Luka Perkov f9c04c8722 kernel: 3.13: refresh patches
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41553
2014-07-08 23:27:45 +00:00
Luka Perkov 82abc5c1d9 kernel: ledtrig-netdev: use netdev_notifier_info
Since kernel 3.11, the third parameter passed to notifier_call()
is of type struct netdev_notifier_info. This patch fixes an oops
when setting a netdev LED trigger.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 41552
2014-07-08 23:27:44 +00:00
Luka Perkov 90b53991a0 kernel: update 3.14 to 3.14.11
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41551
2014-07-08 22:44:34 +00:00
Jonas Gorski 8630d101b7 brcm63xx: fixup patches borked by allowing too much fuzz
Move defines and board_info structs back to their proper locations so
(de-)selecting SOC support won't break the build.

Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41550
2014-07-08 12:27:55 +00:00
Hauke Mehrtens 0a5145e851 brcm47xx: make reboot a more reliable
A reboot is issued by setting the watchdog timer to a low value, when
the value is decreased from 1 to 0 by the hardware the system will
reboot. Setting this value to 1 does not work every time, it is a
little bit more reliable when setting it to 3. This timer runs with
some MHz or KHz so nobody will notice the increased waiting.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41548
2014-07-07 20:12:40 +00:00
Hauke Mehrtens f42c36ea60 brcm47xx: add buttons support for Netgear WNR3500L
Ticket: #14406

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41547
2014-07-07 19:14:22 +00:00
Hauke Mehrtens 4632347879 brcm47xx: remove unneeded images from generic target
broadcom-wl now builds in the mips74k profile, so remove these chips
from the generic profile.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41546
2014-07-07 17:47:24 +00:00
Felix Fietkau 8a792ca2bb rb532: remove broken mark
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41544
2014-07-07 08:52:06 +00:00
Felix Fietkau 075249997f rb532: add wan interface
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41543
2014-07-07 08:52:02 +00:00
Felix Fietkau 9a4ba281f6 rb532: fix jffs2 images
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41542
2014-07-07 08:51:59 +00:00
Felix Fietkau d4158338c9 rb532: really fix squashfs images
The previous attempt (r40717) to fix squashfx made the system bootable but
overlayfs remained broken.
This enables block2mtd again using the right partition number and naming
and adds MTD_ROOTFS_SPLIT option.
However onboard rootfs partition name had to be renamed to place overlay on
CF instead of onboard NAND.

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41541
2014-07-07 08:51:55 +00:00
Hauke Mehrtens e63318d6d5 kernel: do not build kernel modules by default
No config option should be set to m in the default config, because
there is also some script needed which picks the module up into the
image and that is missing this way. Always create a kmod when building
a module.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41539
2014-07-06 22:34:24 +00:00
Hauke Mehrtens 2518f83f6e mpc83xx: add support for kernel 3.10
This is compile tested only, please run test and report back.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41538
2014-07-06 22:23:53 +00:00
Hauke Mehrtens deee38e709 mpc52xx: add support for kernel 3.10
This is compile tested only, please run test and report back.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41537
2014-07-06 22:05:09 +00:00
Hauke Mehrtens 157cf7e582 au1000: add support for kernel 3.10
This is compile tested only, please run test and report back.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41534
2014-07-06 18:20:59 +00:00
Luka Perkov 354a1042cc kernel: update 3.14 to 3.14.10
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41533
2014-07-06 18:10:49 +00:00
Jonas Gorski ce0f954947 ar7: enable the low-memory feature flag
Most ar7 devices have only 16 MiB RAM, so select low_mem to give them
a chance to work.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41532
2014-07-06 18:09:30 +00:00
Hauke Mehrtens 3f78cadedd gemini: add support for kernel 3.10
This is compile tested only, please run test and report back.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41531
2014-07-06 17:51:14 +00:00
Hauke Mehrtens 3597b7d456 brcm47xx: image: legacy: take over old devices images
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41530
2014-07-06 17:21:37 +00:00
Hauke Mehrtens 0eb3c26e7d brcm47xx: image: mips74k: take over some device images
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41529
2014-07-06 17:14:29 +00:00
Hauke Mehrtens c3b3df1da8 brcm47xx: image: prepare for using mips74k subtarget
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41528
2014-07-06 17:14:06 +00:00
Hauke Mehrtens df8741f92b brcm47xx: fix bcm4705 rebooting when initializing the switch.
When the Ethernet controller is powered down and someone wants to
access the mdio bus like the witch driver (b53) the system crashed if
PCI_D3hot was set before. This patch deactivates this power sawing mode
when a switch driver is in use.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41527
2014-07-06 13:45:43 +00:00
Hauke Mehrtens ed0dc1c97e b53: hardcode reset GPIO for Linksys WRT300N 1.1
According to the thread https://forum.openwrt.org/viewtopic.php?id=48281
b53 uses GPIO 7:
[    4.470000] b53_common: [DBG] b53_switch_reset_gpio using 7
and causes device to self-reboot. GPIO 8 was found in CFE boot log:
"Reset switch via GPIO 8 ..."

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41526
2014-07-06 11:40:51 +00:00
Hauke Mehrtens ce3fb94567 cns21xx: make patch apply again
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41522
2014-07-05 23:36:05 +00:00
Hauke Mehrtens 7f2f585c13 kernel: add missing config options
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41521
2014-07-05 23:35:36 +00:00
Hauke Mehrtens 356663cdc8 brcm47xx: add LEDs for Netgear WNR3500L
https://dev.openwrt.org/ticket/14406

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41520
2014-07-05 23:25:26 +00:00
Hauke Mehrtens 8e4efd42d9 brcm47xx: make it possible to unregister the adm switch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41517
2014-07-05 21:35:15 +00:00
Hauke Mehrtens 03e2310a38 brcm47xx: fix LEDs on WRTSL54GS
https://dev.openwrt.org/ticket/16991

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41516
2014-07-05 19:40:15 +00:00
Hauke Mehrtens 77dee19ab4 brcm47xx: increase fallback mac addresses by one
Now the mac address is increased by two for the first fallback mac
address. It could be that the address increased should be used for the
wan port.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41515
2014-07-05 19:36:49 +00:00
Hauke Mehrtens 3fff38f93a brcm47xx: do not use mac addresses with 00:90:4C prefix, prevent mac address collisions.
The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used
all devices from the same series are sharing the same mac address.
To prevent mac address collisions we replace them with a mac address
based on the base address.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41513
2014-07-05 15:04:50 +00:00
Hauke Mehrtens 163fe41c75 brcm47xx: get switch name from swconfig first
Without this patch the switch config for the adm switch did not worked,
because hey are not names eth0.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41512
2014-07-05 12:15:03 +00:00
Hauke Mehrtens 286ff7e322 adm6996: the GPIO interface for the adm6996l does not support switch statistics.
This patch deactivates the statistics, adds a missing lock
initialization and fixes a waring.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41511
2014-07-05 12:13:56 +00:00
John Crispin 2abbe82a5a ar71xx/rb532: move rc32434-fix-broken-pci.patch to the correct target
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41507
2014-07-04 08:28:40 +00:00
Jonas Gorski ffae660fbd brcm63xx: disable AUDIT
Reduces kernel size by about 24k (6k compressed).

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41506
2014-07-04 08:23:19 +00:00
John Crispin 49845f855a ar71xx: MIPS: RC32434: fix broken PCI resource initialization
https://patchwork.linux-mips.org/patch/6940/

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41505
2014-07-04 06:33:00 +00:00
Hauke Mehrtens 3f64bb8f8f brcm47xx: add LEDs for Asus RT-N15U and update RT-N66U
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41501
2014-07-03 21:41:33 +00:00
Hauke Mehrtens 9467896172 brcm47xx: migrate basic network settings from old releases
Old OpenWrt releases were using network configs that are not valid
anymore. They were specifying ports tagging in a different way (or were
not tagging CPU at all) and were using VID 0 which is a reserved value.

Modifying network configuration to apply all needed changes would be
pretty tricky. Script /etc/init.d/netconfig that generates new config is
quite complex itself.
So instead let's save the most important settings, regenerate config
from the scratch and restore values. This should work for 99% of users.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41500
2014-07-03 21:40:59 +00:00
Hauke Mehrtens 30a900cab8 kernel: add missing config option
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41499
2014-07-03 20:22:33 +00:00
Florian Fainelli f68f14cc30 realview: set LAN interface to be in DHCP
Realview is mostly used as a QEMU development platform, which will provide a
built-in DHCP server to NAT or bridge the connection outside of the emulated
environment.

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 41495
2014-07-03 17:19:10 +00:00
Florian Fainelli 8f4167ccbf realview: disable SWP emulation
This is not needed since our toolchain produces the expected binaries for the
target CPU.

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 41494
2014-07-03 17:18:58 +00:00
Hauke Mehrtens 5996160a66 brcm47xx: add CONFIG_LEDS_GPIO_REGISTER
CONFIG_LEDS_GPIO_REGISTER is selected by the bcm47xx arch code.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41488
2014-07-02 22:07:46 +00:00
Hauke Mehrtens f95fc5b2d5 brcm47xx: refresh patches
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41487
2014-07-02 22:03:03 +00:00
Hauke Mehrtens ba1b49dbab brcm47xx: backport BCM47XX Linksys WRT54G series patches
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41486
2014-07-02 21:54:59 +00:00
John Crispin b4e46a807c kernel: disable CONFIG_IRQ_ALL_CPUS by default
this fixes the mpc85xx build error

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41477
2014-07-02 18:52:36 +00:00
John Crispin bbfb3baaed ramips: add missing rt3352 usb phy node to dts
Signed-off-by: michael <igvtee@gmail.com>

SVN-Revision: 41476
2014-07-02 16:37:30 +00:00
John Crispin 62287e589d ramips: fix target rt5350 only have 28 gpios
Signed-off-by: michael <igvtee@gmail.com>

SVN-Revision: 41475
2014-07-02 16:37:26 +00:00
John Crispin 1179d4f924 lantiq: UbinizeImage instead of lantiq-specific ubinize.cfg files
New make target in lantiq to use UbinizeImage and SysupgradeNand.
Only enabled for BTHOMEHUBV2B for the moment but should be useable
for other lantiq nand boards.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41474
2014-07-02 16:37:23 +00:00
John Crispin e2915c6981 lantiq: add support for /tmp/sysinfo
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41472
2014-07-02 16:33:11 +00:00
John Crispin 80e3282739 ralink: make xhci platform depend on mt7621
this broke CONFIG_ALL builds for mt7620

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41471
2014-07-02 14:32:43 +00:00
John Crispin cad9e554b1 ar71xx: add missing config symbol
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41455
2014-07-02 08:00:44 +00:00
John Crispin 313db9d0ee lantiq: fix missing symbols
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41454
2014-07-02 07:43:32 +00:00
John Crispin 3d81a4ef82 ralink: add Wansview NCS601W IP Camera
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41453
2014-07-02 07:42:44 +00:00
John Crispin c749b310ed ralink: register wifi firmware for WRTnode
After r41444 wifi working on WRTnode. Tested.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41452
2014-07-01 18:17:55 +00:00
John Crispin 3519322e62 ar71xx: Add support for MikroTik RouterBOARD SXT Lite
This patch adds support for the MikroTik RouterBOARD SXT Lite.

The new RB911L series is also supported as a result.

v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41450
2014-07-01 13:38:30 +00:00
John Crispin 5f31f01853 lantiq: Enable LANTIQ_PHY and LANTIQ_XRX200 only in XRX200 subtarget
Enable LANTIQ_PHY and LANTIQ_XRX200 only in XRX200 subtarget.

These drivers are not needed for ASE, Danube and AR9.
As side effect PHY11G and PHY22F firmwares are not included in the
kernel image, which saves 64 KB.

Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41449
2014-07-01 13:18:38 +00:00
John Crispin 9c84f72f85 ramips: set default vid of each vlan, so it won't need be set explicitly.
Signed-off-by: Xiongfei Guo <xfguo@credosemi.com>

SVN-Revision: 41448
2014-07-01 13:18:27 +00:00
John Crispin 4ddc0f9ff3 ramips: add WHR-1166 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41447
2014-07-01 10:26:42 +00:00
John Crispin 3c88de0d47 ramips: sync the WHR-600D flash layout with that of the vendor FW
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41446
2014-07-01 10:26:38 +00:00
John Crispin 2e8c6e4128 ramips: add wmac to mt7620a device tree
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41445
2014-07-01 10:26:33 +00:00
John Crispin 5f6e7e1f44 ramips: add wmac to mt7620n device tree
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41444
2014-07-01 10:26:30 +00:00
John Crispin bbd8f9c96a ramips: enable wmac clock for mt7620
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41443
2014-07-01 10:26:25 +00:00
Imre Kaloz b7b222279c set led triggers for the Linksys WRT1900AC
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41436
2014-07-01 09:45:41 +00:00
Imre Kaloz 6fa01eab80 adjust default profile, and add an evalboard one
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41435
2014-07-01 09:43:38 +00:00
Imre Kaloz 9ff59c7656 drop unneeded file
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41433
2014-07-01 09:35:22 +00:00
Jonas Gorski 2289e58252 brcm63xx: fix Livebox 1 support
The Livebox 1 support is currently broken. Fixed with this patch

Fixes:
- Redboot partitioning broken: fixed
- Replaced custom ephy reset with platform code
- USB code breaks the building process: fixed
- Led colors
- Removed unneded EHCI code since bcm6348 only has OHCI

Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: drop unneded parts since merge, fixup to apply to current head]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41424
2014-06-30 13:34:43 +00:00
Jonas Gorski dc230d9b0f brcm63xx: 3.10: backport multi-board support
There have been no reported regressions, so backport it to 3.10.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41422
2014-06-30 13:34:37 +00:00
Jonas Gorski 44ef9f7789 brcm63xx: Add support for Comtrend WAP-5813n
This adds support for Comtrend WAP-5813n.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41421
2014-06-30 13:34:34 +00:00
Jonas Gorski 439fe41813 brcm63xx: CPVA502+ board fixes
Some fixes for Telsey CPVA502+ bcm6348 routers:
- reset the external PHY (eth1) with proper platform code, not using a led definiton
- eth1 is an external phy, not a switch, deleted forced link speed
- fixed led color

Patch made for 3.14 kernel patches.

Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: also fix 3.14, refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41420
2014-06-30 13:34:28 +00:00
Luka Perkov 26b06940a9 mvebu: drop 3.10 support
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41406
2014-06-29 23:29:57 +00:00
Imre Kaloz 1cebada22b fix the WPS button's GPIO number on the mamba
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41392
2014-06-29 21:26:01 +00:00
Jonas Gorski f9aeee6a6a kernel: add missing config symbols
Spotted by several buildbots.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Patchwork: http://patchwork.openwrt.org/patch/5768/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41391
2014-06-29 18:36:39 +00:00
Imre Kaloz 6e59193e88 upgrade to Linux 3.14.9
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41388
2014-06-29 13:11:57 +00:00
Imre Kaloz 3e4932758e build firmware images for the Mamba (Linksys WRT1900AC)
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41387
2014-06-29 13:10:35 +00:00
Imre Kaloz 0bc385d064 set nand and squashfs features
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41386
2014-06-29 13:09:15 +00:00
Imre Kaloz b2e9df4de3 add uboot-envtools by default
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41385
2014-06-29 13:06:48 +00:00
Imre Kaloz 974f13988c handle the dual-firmware layout on the WRT1900AC
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41384
2014-06-29 13:03:55 +00:00
Imre Kaloz d59f68531b use the power led on the WRT1900AC for status reporting
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41383
2014-06-29 12:53:09 +00:00
Imre Kaloz 2c06f05236 fixup mac addresses on the WRT1900AC
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41382
2014-06-29 12:51:39 +00:00
Imre Kaloz f953ed4ffb automatically generate network config
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41381
2014-06-29 12:50:12 +00:00
Imre Kaloz 38f596d8f4 update mamba dts
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41379
2014-06-29 11:44:58 +00:00
Felix Fietkau 8fe75736d8 kernel: add missing config symbol
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41378
2014-06-29 11:35:07 +00:00
Felix Fietkau e736343df9 xburst: remove bogus led support override
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41373
2014-06-29 10:25:30 +00:00
John Crispin 639682dfdb x86/kvm_guest: fix out of sync config-3.10
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41372
2014-06-29 10:11:17 +00:00
Felix Fietkau a75354ef53 kernel: implement optinal multicast->unicast conversion for igmp snooping
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41367
2014-06-28 22:27:54 +00:00
Felix Fietkau 33ad14a920 kernel: enable bridge igmp snooping
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41366
2014-06-28 22:27:49 +00:00
Felix Fietkau 79c8b619e4 ar71xx: refresh patches
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41365
2014-06-28 22:27:46 +00:00
Felix Fietkau 555e876d73 xburst: remove bogus config override
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41364
2014-06-28 19:48:03 +00:00
Florian Fainelli 54c4771077 ar7: backport an upstream fixing serial console
Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 41363
2014-06-27 22:17:00 +00:00
Luka Perkov abc694b463 kernel: update 3.14 to 3.14.9
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41362
2014-06-27 21:10:02 +00:00
Imre Kaloz 4fe76889c0 update config for 3.14
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41361
2014-06-27 20:38:42 +00:00
Imre Kaloz 75083c6e68 build squashfs on ubi and SysupgradeNAND images
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41360
2014-06-27 13:00:25 +00:00
John Crispin 22c4f2475b ralink: refresh kernel patches
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41353
2014-06-26 13:47:50 +00:00
John Crispin fbf8b288e1 kernel: refresh generic patches
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41352
2014-06-26 13:47:46 +00:00
John Crispin 994e5ce2f9 kernel: update 3.10.36->3.10.44
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41351
2014-06-26 13:47:42 +00:00
John Crispin 23a9bfc655 ar71xx: r41348 is missing these files
sorry, the downside when applying patches with patch

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41350
2014-06-26 13:47:35 +00:00
John Crispin e6e6a85dc9 ar71xx: add support for EasyLink M150 and M-mini
v3 refreshes the patch on trunk@41337

This patch adds support for the EasyLink EL-M150 and M-mini

http://wiki.openwrt.org/toh/easylink/el-m150
http://wiki.openwrt.org/toh/easylink/el-m-mini

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 41348
2014-06-26 11:49:47 +00:00
John Crispin baa534a8b7 ar71xx: nbg6716: Enable procd nand sysupgrage
This enables the procd nand upgrade for ZyXEL NBG 6716. Also the ubi config
is cleaned up to match the wndr4300.

Signed-off-by: André Valentin <avalentin@marcant.net>

SVN-Revision: 41346
2014-06-26 11:43:38 +00:00
John Crispin 975728813a ralink: fix up WRTNode vs WRTNODE in the dts file
https://dev.openwrt.org/ticket/16899

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41343
2014-06-26 11:43:26 +00:00
Luka Perkov cb3d5242ca mvebu: drop preinit script
The /lib/mvebu.sh script can now handle this task.

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41341
2014-06-26 10:21:32 +00:00
Luka Perkov fa0b9bccea imx6: move imx6.sh to /lib/ for consistency
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41339
2014-06-26 10:14:13 +00:00
Luka Perkov a54f4320f9 kirkwood: move kirkwood.sh to /lib/ for consistency
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41338
2014-06-26 10:13:47 +00:00
Luka Perkov 8416523dba kirkwood: base-files: use /lib/functions/kirkwood.sh
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41336
2014-06-24 18:18:53 +00:00
Luka Perkov e6aea925d3 kirkwood: base-files: add script to detect board name and populate /tmp/sysinfo
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41335
2014-06-24 18:18:51 +00:00
John Crispin 1bb3e5c40a ar71xx: fix wndr3700v4 image header
https://dev.openwrt.org/ticket/16840

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41333
2014-06-24 18:14:23 +00:00
John Crispin fcb8eb5d7d ar71xx: remove old jffs2 marker from image generation on nand targets
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41332
2014-06-24 18:14:18 +00:00
John Crispin 021e728962 ralink: Update MT7530 switch driver.
- Support set VLAN ID of each vlan.
- Support untag feature.
- Replace register address with C MACRO.
- There are 8 ports for MT7530 actually.

Signed-off-by: Xiongfei Guo <xfguo@credosemi.com>

SVN-Revision: 41331
2014-06-24 18:14:14 +00:00
John Crispin 0708bda7c6 mpc83xx: add missing kernelnames into Makefile
add missing kernelnames to Makefile because those files are needed in 'target/linux/mpc83xx/image/Makefile'. Without them a compilation for mpc83xx is not possible - the buildbot stops with the error "No such file or directory"

Signed-off-by: Claudio Thomas <ct@xmodus-systems.de>

SVN-Revision: 41330
2014-06-24 18:14:09 +00:00
John Crispin 22a35a7b11 SysupgradeNAND: include rootfs-type in image name
also add quotes to paths

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 41326
2014-06-24 18:13:51 +00:00
John Crispin bcc7374d7d atheros[ar2315-spiflash]: remove duplicated definitions
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41325
2014-06-24 18:13:47 +00:00
John Crispin 78bdfeb30b atheros[ar2315-spiflash]: update driver id
Make id more specific and consistent with others platform drivers.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41324
2014-06-24 18:13:43 +00:00
John Crispin 69e02dadf1 atheros[ar2315-spiflash]: make local variables and functions static
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41323
2014-06-24 18:13:39 +00:00
John Crispin cef87d67f9 atheros[ar2315-spiflash]: I/O fixes
Directly use ioread/iowrite functions to avoid odd dependency. And
carefully annotate I/O memory pointers.

Singed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41322
2014-06-24 18:13:35 +00:00
John Crispin cce27e3b95 atheros[ar2315-spiflash]: make spiflash header local
We do not need global access to it, so move it from arch include to the
mtd subdir.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41321
2014-06-24 18:13:31 +00:00
John Crispin 08a9fcb0ef atheros[ar2315-spiflash]: pass I/O mem regions via resources
Pass I/O memory regions (flash read and MMR) via platform device
resources array and use them inside spiflash driver.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41320
2014-06-24 18:13:27 +00:00
John Crispin 1dab970e8b atheros[ar231x-pci]: do not touch iomem_resource ranges
Moving the start of IO mem to 0x10000000 leads to allocation conflict
with SPI flash memory region, which starts at 0x08000000.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41319
2014-06-24 18:13:22 +00:00
John Crispin 79b4598a7f atheros[ar2315-spiflash]: print detected flash size
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41318
2014-06-24 18:13:17 +00:00
John Crispin 8e3b055b2a atheros[ar2315]: don't detect flash size during board initialization
We should not detect actual flash size during board initialization to
find board config at the end of the flash, just use large enough mapping
size (currently 128 mbit). If mapping size is larger than the actual
flash size, than flash will simply be mapped multiple times. This change
simplifies code by removing duplication and saves about 200 bytes of
uncompressed kernel :)

Tested with Ubnt LS2 board equipped with STM 25p32v6p NOR flash (32 mbit).

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41317
2014-06-24 18:13:13 +00:00
John Crispin f8893629ec atheros[ar231x-eth]: merge patch
Merge 3_10-updates.patch into the ar2313_ethernet.patch since it contains
only one ethernet driver fix.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41316
2014-06-24 18:13:09 +00:00
John Crispin d219e055be lantiq: remove deprecated jffs2_nand configuration
As far as I am aware, amongst the lantiq boards, jffs2_nand was
only used on the BTHOMEHUBV2B. Ubi-related modifications to the
device tree for that board mean that the resulting jffs2 images
no longer work, and are no longer required anyway. So I suggest
removing the related configuration, which this patch does.

If anyone else is using jffs2_nand on a lantiq target please speak
up!

Incidentally, for a jffs2 rootfs partition concatenated to the
kernel image to be recognised and mounted correctly on nand
this patch or something equivalent is required:
http://patchwork.openwrt.org/patch/5110/
It is marked as accepted in patchwork but doesn't seem to have
been committed. As far as I am concerned it too is deprecated.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41312
2014-06-24 18:12:52 +00:00
John Crispin aca708e4e6 lantiq: ubinize autoresize flag for rootfs_data
Setting this flag allows rootfs_data to expand on first boot
to fill remaining free space on nand.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41310
2014-06-24 18:12:41 +00:00
Luka Perkov 70a27a518e kernel: update 3.14 to 3.14.8
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41309
2014-06-24 12:27:36 +00:00
Jonas Gorski 43cc8c3ebe brcm63xx: allow bcm963xx and livebox support at the same time
Use the CFE_EPTSEAL to tell them apart at runtime. Added for now only
for the 3.14 until properly tested.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41296
2014-06-21 19:23:38 +00:00
Jonas Gorski 21d65bb185 brcm63xx: update variant detection patches and fix VARID shift
The variant id field shift was wrong, causing the variant detection
to fail.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 41295
2014-06-21 19:23:28 +00:00
Jonas Gorski f695fa358a brcm63xx: fix up borked patch
Fix up patch borked by quilt fuzzy application of patches.

SVN-Revision: 41294
2014-06-21 19:23:18 +00:00
Imre Kaloz e1de4e27c1 coding style cleanups, drop old kernel support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41293
2014-06-21 10:00:07 +00:00
Imre Kaloz 643a8a626d update mamba dts
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41292
2014-06-20 23:05:23 +00:00
Imre Kaloz f11de38d44 make script executable, add WRT1900AC detection
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41291
2014-06-20 22:35:09 +00:00
Imre Kaloz a241853358 define the power led for the WRT1900AC
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41288
2014-06-20 19:13:01 +00:00
John Crispin a8d532abf2 octeon: add sysupgrade support for the erlite
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41286
2014-06-20 13:41:16 +00:00
John Crispin fe79b06e6b octeon: build a sysupgrade image for erlite
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41285
2014-06-20 13:41:12 +00:00
John Crispin cf80a59dcc imx6: add sysupgrade support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41277
2014-06-19 14:13:38 +00:00
John Crispin 1a60486acb imx6: the script populating /tmp/sysinfo/ was in the wrong path
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41276
2014-06-19 14:13:34 +00:00
John Crispin e0d57509ad octeon: enable the ext4 feature
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41275
2014-06-19 14:13:30 +00:00
John Crispin e6e024f155 octeon: add basic board detection
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41274
2014-06-19 14:13:20 +00:00
John Crispin 0d5a6fd819 kernel: drop now unused ubi forced detach patch
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41272
2014-06-19 14:13:12 +00:00
John Crispin 9284956ad8 ramips: cleanup some rt305x profiles
move both asus boards to asus.mk
rename HW5503G profile to HW550-3G to match name in image/Makefile
(fixes #16599)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 41271
2014-06-19 14:13:07 +00:00
John Crispin 432f7e52db lantiq: copy rootfs-overlay.ubi to bin/lantiq
At the moment, an rootfs.ubi is copied over to bin/lantiq
but rootfs-overlay.ubi is not. This adds it.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41270
2014-06-19 14:13:04 +00:00
John Crispin 6c46a10246 lantiq: refresh patches
this adds ben's ath9k fixup

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41269
2014-06-19 14:12:59 +00:00
Florian Fainelli 43c0ad0f00 imx6: fix typo on wandboard detection
Revision r41256 introduced a typo (wandaboard => wandboard), but later
revisions expect to match on "wandboard"

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 41262
2014-06-18 16:34:23 +00:00
John Crispin efcec0faaf imx6: use /lib/imx6.sh inside the uci-defaults script
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41257
2014-06-18 10:08:16 +00:00
John Crispin 2773bdfebf imx6: add a script to detect the board name and populate /tmp/sysinfo
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41256
2014-06-18 10:08:12 +00:00
John Crispin 23cdea78d8 ar71xx: Fixes for 951Ui-2HnD board support
WAN and LAN are swapped the wrong way around.  This patch fixes that by adding the 951Ui-2HnD to ar71xx.sh and the relevant entry in 02_network.

This patch also defines the ACT LED as the status LED in diag.sh.

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41255
2014-06-18 10:08:08 +00:00
John Crispin 5aeb5c1cbc octeon: fix up the cpu flags
Signed-off-by: Martin Fäcknitz <faecknitz@hotsplots.de>

SVN-Revision: 41253
2014-06-18 10:08:01 +00:00
John Crispin 312fca5455 octeon: add 3 upstream patches that fix issues on the esr-lite
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41252
2014-06-18 10:07:57 +00:00
Luka Perkov 5e6024d526 mvebu: be consistent with kernel config file names
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41240
2014-06-17 21:04:45 +00:00
John Crispin 575127fe1c lantiq: DGN3500 (all known variants) factory and sysupgrade image building support
This patch adds factory image building for the DGN3500, all variants,
and fixes sysupgrade images to make them play nice with the sercomm
secondary boot loader.

The factory images can be used directly in the update dialog in the
interface of the stock firmware and via the special Sercomm bootmode
and a special windows flashing utility (allegedly present in the CD
that came with the device -- but it's also compatible with the NSLU2
Upgrade_207_XP utility.) The special bootmode can be activated by
turning the device on while holding the reset button pressed, then
releasing it when the power led starts blinking red and green. Please
notice that if using the 207 utility, it will always report that the
flashing failed even though it completed successfully. Just power
cycle the router manually after the utility reports the failure and
OpenWRT will boot. This same utility (despite reporting failure in
this case too) can revert a DGN3500 (any variant) to the appropriate
stock Netgear firmware.

This patch is a heavily modified version of a package I found on the
OpenWRT forum with a couple fixes and features added -- mainly the
generation of all the different image variants to support all known
models directly, atm known variants are AnnexA-WW, AnnexA-NA and
AnnexB-DE/GR.

I tested the patch successfully on my device.

Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>

SVN-Revision: 41236
2014-06-17 15:38:54 +00:00
Imre Kaloz 85812e21f9 add dummy fixup for 3.10
SVN-Revision: 41234
2014-06-17 15:14:02 +00:00
Imre Kaloz ac91824b36 build images for the WRT1900AC
SVN-Revision: 41233
2014-06-17 15:13:33 +00:00
Imre Kaloz d775e4ef00 preliminary support for the WRT1900AC (work in progress)
SVN-Revision: 41232
2014-06-17 15:13:10 +00:00
Jo-Philipp Wich 93742047af mpc85xx: fix typo in TP-Link WDR4900 profile
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 41229
2014-06-17 15:01:47 +00:00
John Crispin dc5fe5f73f ramips: RT-N56U support fixes and factory image creation
Signed-off-by: Mikko Hissa <mikko.hissa@werzek.com>

SVN-Revision: 41224
2014-06-16 18:57:20 +00:00
John Crispin 3dca5a158d procd: various cleanups to /lib/upgrade/nand.sh
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41222
2014-06-16 18:55:14 +00:00
John Crispin c5461a78d2 kernel/3.1{0, 2, 3, 4}: mtd: m25p80: add support for EON EN25QH128
This flash is used in newer Ubnt UniFi AP Pro

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41219
2014-06-16 18:55:01 +00:00
John Crispin ae8caf216f kernel: replace a ubifs patch by upstream commit
A modified version of 552-ubifs-respect-silent-mount-flag.patch has
been merged upstream. Replace the patch in OpenWrt with the version
which has been merged.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 41218
2014-06-16 18:54:57 +00:00
John Crispin 4d7ed2a8a0 ramips: fixes XDXRN502J reset button
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41217
2014-06-16 18:54:53 +00:00
John Crispin 2fe435081d ramips: add vlan configuration for asiarf awm002-evb
Without this, the ports all end up on vlan 1.  This enables a separate
WAN port that works.

Signed-off-by: Russell Senior <russell@personaltelco.net>

SVN-Revision: 41216
2014-06-16 18:54:48 +00:00
John Crispin ab390d6c05 ramips: restore AWM002-EVB profile in asiarf.mk
In a recent revision (r41177) John Crispin removed the profile for the
AsiaRF AWM002 eval board while adding another AsiaRF board.  This
patch restores AWM002 and also corrects a misspelling and an
apparently errant reference to an Allnet ALL0239-3G device.

Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Signed-off-by: Russell Senior <russell@personaltelco.net>

SVN-Revision: 41215
2014-06-16 18:54:42 +00:00
John Crispin 85ca75decd lantiq BTHOMEHUBV2B - update dts for automatic detection of ubi partition and rootfs type
This patches the BTHOMEHUB2B device tree to make use of the
new code for automatic detection of the ubi partition and the
rootfs type within it. Gets rid of the ugly alternative bootargs
lines.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 41214
2014-06-16 18:54:38 +00:00
John Crispin e6c46554bb lantiq: fixup vgv7519 usb support
https://dev.openwrt.org/ticket/16800

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41213
2014-06-16 18:54:33 +00:00
Felix Fietkau 841b730f98 kernel: fix pkt_type filter mask for packet sockets
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41178
2014-06-13 09:34:03 +00:00
John Crispin 6d213a644d ramips: add asiarf awapn2403 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41177
2014-06-13 09:16:15 +00:00
Steven Barth 285af2ff08 Update UML target to 3.10 and various improvements
Updated target to 3.10.36.
Added mconsole exec patch.
Added pseudo-random MAC patch (from NetKit).

Signed-off-by: Markus Stenberg <markus.stenberg@iki.fi>
Reviewed-by: Steven Barth <steven@midlink.org>

SVN-Revision: 41172
2014-06-12 17:57:19 +00:00
Luka Perkov f45b1a671a kernel: update 3.14 to 3.14.7
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 41150
2014-06-11 23:39:54 +00:00
Felix Fietkau 231f15c9db ramips: fix rt2x00 handling of default packages for subtargets
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41145
2014-06-11 17:01:19 +00:00
John Crispin e9f664c879 kernel: make sure the new UBIBLOCK symbol does not break builds
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41134
2014-06-11 13:00:17 +00:00
John Crispin 4096a110fb ar71xx: activate the nand sutarget
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41133
2014-06-11 13:00:12 +00:00
John Crispin fe6e2f8e1b ar71xx: fix up kernel config for the nand subtarget
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41132
2014-06-11 13:00:04 +00:00
John Crispin c973fb031e ar71xx: add sysupgrade support for wndr4300
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41131
2014-06-11 13:00:00 +00:00
John Crispin 9a0b4ab4ed ar71xx: remove the explicit ubi.mtd- paramaters and rename ubiroot to ubi
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41130
2014-06-11 12:59:57 +00:00
John Crispin ac5d5cbc79 kernel: add a NAND_SUPPORT symbol
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41122
2014-06-11 12:59:22 +00:00
John Crispin c8d472c37f kernel: backport the ubiblock patches from 3.14->3.10
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41120
2014-06-11 12:59:15 +00:00
John Crispin acbcd5f5b5 kernel: rootfs auto-mount on ubi
Similar to the rootfs hacks on NOR flash devices, this series
introduces support for auto-attaching (ubi device), auto-creating
(ubiblock device) and mounting the "rootfs" (ubifs or squashfs)
volume.
This is needed so OpenWrt can start without relying on the bootloader
to pass the ubi.mtd, ubi.block, rootfs and rootfstype parameters, but
instead auto-detect the root filesystem according to a simple convention.

OpenWrt-specific:
490-ubi-auto-attach-mtd-device-named-ubi-or-data-on-boot.patch
491-ubi-auto-create-ubiblock-device-for-rootfs.patch
492-try-auto-mounting-ubi0-rootfs-in-init-do_mounts.c.patch
493-ubi-set-ROOT_DEV-to-ubiblock-rootfs-if-unset.patch

sent upstream:
552-ubifs-respect-silent-mount-flag.patch
http://lists.infradead.org/pipermail/linux-mtd/2014-May/053893.html

v2: actually retry with MS_RDONLY when mounting read-only ubifs root

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 41119
2014-06-11 12:59:10 +00:00
John Crispin d494983d02 kernel: backport ubiblock support from 3.15
Backport ubiblock support from kernel 3.15 as well as all follow-up
fixes related to ubiblock.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

 create mode 100644 target/linux/generic/patches-3.14/040-UBI-R-O-block-driver-on-top-of-UBI-volumes.patch
 create mode 100644 target/linux/generic/patches-3.14/041-UBI-block-do-not-use-term-attach.patch
 create mode 100644 target/linux/generic/patches-3.14/042-UBI-block-Mark-init-only-symbol-as-__initdata.patch
 create mode 100644 target/linux/generic/patches-3.14/043-UBI-block-Use-u64-for-the-64-bit-dividend.patch
 create mode 100644 target/linux/generic/patches-3.14/044-UBI-rename-block-device-ioctls.patch
 create mode 100644 target/linux/generic/patches-3.14/045-UBI-block-Remove-__initdata-from-ubiblock_param_ops.patch
 create mode 100644 target/linux/generic/patches-3.14/046-UBI-avoid-workqueue-format-string-leak.patch
 create mode 100644 target/linux/generic/patches-3.14/047-UBI-make-UBI_IOCVOLCRBLK-take-a-parameter-for-future.patch

SVN-Revision: 41118
2014-06-11 12:59:06 +00:00
Felix Fietkau 75b4c400c7 atheros: fix too short msleep
Use msleep(20) instead of msleep(10) to make code closer to reality
since msleep can sleep for up to 20ms even we request shorter delay.
All updated calls are located in PCI initialization routine which is
called only once upon device boot. So there should be no performance
issues caused by more longer delay.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41096
2014-06-10 09:06:25 +00:00
Felix Fietkau e49636472d atheros: shorten lines
Wrap lines over 80 chars or make them shorter by other ways.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41095
2014-06-10 09:06:22 +00:00
Felix Fietkau a6cf23b76c atheros: constify some static structures
Constify some static structures as suggested by checkpatch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41094
2014-06-10 09:06:18 +00:00
Felix Fietkau f363db0094 atheros: avoid __FUNCTION__ usage
Use __func__ instead of gcc specific __FUNCTION__ as suggested by
checkpatch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41093
2014-06-10 09:06:14 +00:00
Felix Fietkau 70b2a81a2e atheros: trailing statements fixes
Move trailing statements to next line with indentation as suggested by
checkpatch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41092
2014-06-10 09:06:10 +00:00
Felix Fietkau 0bca3f9547 atheros: spaces fixes
Add missed spaces and remove odd space as suggested by checkpatch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41091
2014-06-10 09:06:06 +00:00
Felix Fietkau dd31da467f atheros: indent fixes
Various indent fixes suggested by checkpatch: use tabs, use same level
of indentation for switch and case, correct indentation levels.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41090
2014-06-10 09:06:03 +00:00
Felix Fietkau 66c64834f8 atheros: fix includes
Remove some unnecessary includes and use <linux/foo.h> instead of
<asm/foo.h> when it possible as suggested by checkpatch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41089
2014-06-10 09:05:58 +00:00
Felix Fietkau 90ca9a582d atheros: various printk(...) fixes
Use more particular functions dev_<level> or pr_<level>(...) insead of
direct printk(...) call. Add KERN_LEVEL to calls what missed it.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41088
2014-06-10 09:05:55 +00:00
Felix Fietkau 15a2ebbc38 atheros: various braces fixes
Fix braces location, remove unnecessary empty lines before or after code
block, remove useless braces. All cases are detected by checkpatch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41087
2014-06-10 09:05:51 +00:00
Felix Fietkau 58d70ff9b3 atheros: do not initialize statics to 0 or false
as suggested by checkpatch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41086
2014-06-10 09:05:47 +00:00
Felix Fietkau 8b4323ad31 atheros: remove trailing whitespace
as suggested by checkpatch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41085
2014-06-10 09:05:43 +00:00
Felix Fietkau 3406e402ef atheros: do not assignment in if condition
Remove assignments from if conditions as suggested by checkpatch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41084
2014-06-10 09:05:40 +00:00
Felix Fietkau 5427e47e59 atheros: remove parentheses around return values
Remove parentheses around return values since return is no a function,
as suggested by checkpatch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41083
2014-06-10 09:05:36 +00:00
Felix Fietkau 630eac6638 atheros: parenthesis around complex macroses value
Use parenthesis around complex macroses value as suggested by
checkpatch.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41082
2014-06-10 09:05:32 +00:00
Felix Fietkau cb50efa835 atheros: various comments fixes
Fix comment issues detected by checkpatch. Convert C99 // comments to
ordinary /* ... */ comments. Correct block comments style or convert
them to single line comments.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41081
2014-06-10 09:05:28 +00:00
Felix Fietkau ea9360a5c6 atheros: avoid CamelCase
Change fooBar variables names to foo_bar as suggested by checkpatch,
write few tables names in lower case and correctly place __initdata
keyword.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 41080
2014-06-10 09:05:25 +00:00