This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite <leitec@staticky.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43153 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add patches for getting the IRQ number for a device of the bcma bus
that were send for upstream inclusion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43148 3c298f89-4303-0410-b956-a3cf2f4a3e73
This makes it possible to activate early printk.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43145 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds a kernel config for kernel 3.18
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43140 3c298f89-4303-0410-b956-a3cf2f4a3e73
The patch adding AR8216_PHY_LEDS was not ported to more recent kernel
versions.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43139 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some changes from the header file were not ported from older kernel.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43137 3c298f89-4303-0410-b956-a3cf2f4a3e73
The select SYS_HAS_DMA_OPS in CPU_CAVIUM_OCTEON was from the kernel
patch in 3.13, but it is only included in kernel 3.14 and not in 3.13
and 3.18, add it again.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43134 3c298f89-4303-0410-b956-a3cf2f4a3e73
Apply patch for kernel 3.10 from r43112 also in 3.12, 3.14 and 3.18.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43133 3c298f89-4303-0410-b956-a3cf2f4a3e73
this caused a crash on boot
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43120 3c298f89-4303-0410-b956-a3cf2f4a3e73
some bootloaders (linksys e1700) set wonky hw trap values. reset this upon boot to make all ports work.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43117 3c298f89-4303-0410-b956-a3cf2f4a3e73
latest mt7530 silicon seems to have a different phy id.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43113 3c298f89-4303-0410-b956-a3cf2f4a3e73
OpenWRT patch 255-lib80211_kconfig_hacks gives user possiblity to select
LIB80211 dependant settings (LIB80211_CRYPT_*) without having LIB80211
selected which is wrong.
My patch changes OpenWRT patch so LIB80211 is vissible and all
LIB80211_CRYPT_* options selects LIB80211 automatically.
Signed-off-by: Tomasz Wasiak <tjwasiak@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43112 3c298f89-4303-0410-b956-a3cf2f4a3e73
Change list:
* add tx scatter gather function.
* add software rx vlan offload to let GRO work.
* add jumbo frame support. because use build_skb so max MTU is 3812.
* enable hardware tx vlan.
* enable GRO and remove LRO. because it can improve performance and can work on forwarding.
* enable/fix tx padding function.
* let napi handle tx clean up.
* support ethtool operation. now support message level, hardware status and coalesce.
* ethtool support use mdio to get phy status only on mt7620. need modify dts file and add phy info to support it.
Notes:
* build and test on rt2880, rt3052, rt3352, rt3662, rt5350 and mt7620a.
* TCP NAT performance improve. test with netperf.
- rt2880(gigabit) from 5x to 12x Mbps.
- rt3x5x from 6x to 94 Mbps.
- rt5250 from 5x to 8x Mbps.
- rt3662(gigabit) from 6x to 42x Mbps with GRO. 23x Mbps without GRO. 66x Mbps with jumbo frame.
- mt7620 still 94Mbps.
* TSO function not tested. because i don't have mt7620 with eco >= 5. and the hardware don't support to set MSS. it will have problem.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43108 3c298f89-4303-0410-b956-a3cf2f4a3e73
Boards that have more than one swconfig enabled switch will show the devices in
reverse order when call swconfig list. Fix this by using list_add_tail().
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43106 3c298f89-4303-0410-b956-a3cf2f4a3e73
0x8100000c vs 0x810000c0 int he pvc register this caused the cascade with an external mt7530 to fail.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43104 3c298f89-4303-0410-b956-a3cf2f4a3e73
(Reposted due to an issue with the patchwork server during original submission)
Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)
Signed-off-by: Gareth Bryan <gareth@mx9.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43102 3c298f89-4303-0410-b956-a3cf2f4a3e73
lantiq_dsl.sh didn't work with VDSL chipsets for now, fix that by
detecting whether vdsl_cpe_control or dsl_cpe_control should be used.
Also add missing quotes around shell string comparision.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43101 3c298f89-4303-0410-b956-a3cf2f4a3e73
This SoC does not have a vfpv3 FPU.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43098 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds initial support for kernel 3.18.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43097 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are still many options missing.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43096 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch 060 we had in repo was never sent/accepted.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43091 3c298f89-4303-0410-b956-a3cf2f4a3e73
This works around a bootloader issue where every device
has the same lan/wan-mac 00:04:9f:ef:01:01 - with this patch
we read the macs from config-partition during initial network
setup. We have 9 valid macs stored in the partition, the
1st two are used for the radios, 3 and 4 are now used for WAN/LAN.
on an already setup / running device we can get the real macs with
. /lib/functions.sh
. /lib/functions/system.sh
echo "LAN = $(mtd_get_mac_binary config 338)"
echo "WAN = $(mtd_get_mac_binary config 344)"
see:
https://dev.openwrt.org/ticket/14714
from the ticket / user klondike:
U-Boot passed this commit ecd1a09b81http://u-boot.10912.n7.nabble.com/U-Boot-PATCH-mpc83xx-remove-hardcoded-network-addresses-from-config-files-td44372.html
I suppose to prevent this particular issue, but the WDR4900 may be using an old bootloader still affected.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
I have been checking the contents of the dtb on the flash, this particular bit is quite revealing:
ethernet@b0000 {
#address-cells = <0x1>;
#size-cells = <0x1>;
device_type = "network";
model = "eTSEC";
compatible = "fsl,etsec2";
fsl,num_rx_queues = <0x8>;
fsl,num_tx_queues = <0x8>;
local-mac-address = [00 00 00 00 00 00];
^^^^^^^^^^^^^^^^^
interrupt-parent = <0x2>;
phy-handle = <0x3>;
phy-connection-type = "rgmii-id";
ptimer-handle = <0x4>;
queue-group@0 {
#address-cells = <0x1>;
#size-cells = <0x1>;
reg = <0xb0000 0x1000>;
rx-bit-map = <0xff>;
tx-bit-map = <0xff>;
interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
};
};
I also have been checking the live device map to find this:
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b0000/local-mac-address
00000000 00 04 9f ef 01 01 |......|
00000006
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b1000/local-mac-address
*
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b2000/local-mac-address
*
My conclussion is that U-Boot most likely finds the device and (as no valid MAC-address is provided)
falls back to the default MAC provided by the old code, the kernel then receives thee modified
device map from U-Boot and assumes this is the correct MAC for the device despite it obviously isn't.
This can be seen at
target/linux/mpc85xx/patches-3.10/140-powerpc-85xx-tl-wdr4900-v1-support.patch
The enetaddr is filled up by using the device tree data by the process_boot_dtb
function and used by the platform_fixups function to set the eth0 address
(by calling dt_fixup_mac_address_by_alias("ethernet0", enetaddr); ).
But instead we should be used the device address which to my understanding is
provided in the mtd.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43074 3c298f89-4303-0410-b956-a3cf2f4a3e73
The existance of this new board has been confirmed and tested by the guy on this commit
76fdd8e638
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43072 3c298f89-4303-0410-b956-a3cf2f4a3e73
All platforms which are using 3.10.x at the moment are upgraded.
Changelogs:
https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.50https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.51https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.52https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.53https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.54https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.55https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.56https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.57https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.58
A new symbol 'X86_16BIT' appeared in 3.10.52 with commit 34273f41d57ee8d854dcd2a1d754cbb546cb548f
("x86-espfix-make-it-possible-to-disable-16-bit-support.patch")
I defaults to 'unset', but it's worth a discussion to enable it
("turn off support for any 16-bit software").
Also removed the patch 0db3db45f5bd6df4bdc03bbd5dec672e16164c4e
("fix build failure on memcpy() in decompress.c")
and is obsolete by commit 29593fd5a8149462ed6fad0d522234facdaee6c8 upstream.
included in kernel 3.10.56
compile tested on all platforms with:
make tools/install
make toolchain/install
make target/linux/compile
user@box:~/user/openwrt$ cat /tmp/log.txt
[Wed Oct 22 00:36:02 CEST 2014] ./smoketest.sh: ar71xx - OK
[Wed Oct 22 00:53:22 CEST 2014] ./smoketest.sh: ar7 - OK
[Wed Oct 22 01:08:27 CEST 2014] ./smoketest.sh: au1000 - OK
[Wed Oct 22 01:21:43 CEST 2014] ./smoketest.sh: avr32 - OK
[Wed Oct 22 01:37:47 CEST 2014] ./smoketest.sh: cns21xx - OK
[Wed Oct 22 01:52:05 CEST 2014] ./smoketest.sh: cns3xxx - OK
[Wed Oct 22 02:10:23 CEST 2014] ./smoketest.sh: gemini - OK
[Wed Oct 22 02:29:07 CEST 2014] ./smoketest.sh: ixp4xx - OK
[Wed Oct 22 02:44:01 CEST 2014] ./smoketest.sh: malta - OK
[Wed Oct 22 02:55:57 CEST 2014] ./smoketest.sh: mpc85xx - OK
[Wed Oct 22 03:07:56 CEST 2014] ./smoketest.sh: orion - OK
[Wed Oct 22 03:24:30 CEST 2014] ./smoketest.sh: ppc40x - OK
[Wed Oct 22 03:40:19 CEST 2014] ./smoketest.sh: ppc44x - OK
[Wed Oct 22 03:55:29 CEST 2014] ./smoketest.sh: realview - OK
[Wed Oct 22 04:09:47 CEST 2014] ./smoketest.sh: sparc - OK
[Wed Oct 22 04:23:37 CEST 2014] ./smoketest.sh: x86 - OK
[Wed Oct 22 04:35:56 CEST 2014] ./smoketest.sh: xburst - OK
run tested on x86, au1000, ar71xx, mpc85xx and brcm47xx
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43049 3c298f89-4303-0410-b956-a3cf2f4a3e73
replace all occurences of LINUX_VERSION with the cleaner
approach. future kernel upgrades must mostly touch only
one file. the only platform left is netlogic, because it
uses a intermediate kernel 3.14.16
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43047 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for Broadcom/Netlogic XLR/XLP support
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43037 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is required due to 306-mips_mem_functions_performance.patch, just
add a memmove() implementation to satisfy the lzma2 decompressor code.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43036 3c298f89-4303-0410-b956-a3cf2f4a3e73
According to the ticket #18152 it also uses NAND with 0x20000 erase size
and 0x800 page size.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43008 3c298f89-4303-0410-b956-a3cf2f4a3e73
SENSORS_VEXPRESS is masked by HWMON
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42984 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix sysupgrade to determine the correct boot block device to use if
/proc/cmdline contains a PARTUUID root.
Change the preinit move_config() hook to use the UUID scanning code
from sysupgrade in order to avoid code duplication.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42968 3c298f89-4303-0410-b956-a3cf2f4a3e73
Enable the required squashfs and block2mtd support in the kernel in order
to be able to actually boot them.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42967 3c298f89-4303-0410-b956-a3cf2f4a3e73
If the underlying block device is a USB device it might require some
time to settle, observed when booting a squashfs image from sd card
on an Alix APU board.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42966 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix the move_config() procedure to properly find the corresponding disk if
the rootfs was mounted by PARTUUID instead of a device node.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42946 3c298f89-4303-0410-b956-a3cf2f4a3e73
This kmod is required by the Alix APU 1D4 to be reachable after
installing an x86-64 image.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42945 3c298f89-4303-0410-b956-a3cf2f4a3e73
We still don't have a smart sysupgrade method, but at least we can use
UBI which provides some protection for rootfs (SquashFS).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42941 3c298f89-4303-0410-b956-a3cf2f4a3e73
UBI requires PEBs to be formatted (with a valid UBI header) or empty
(0xFF), however CFE doesn't clear blocks after flashing the image. To
workaround this problem, teach UBI to recognize EOF mark in a similar
way JFFS2 handles that in OpenWrt.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42940 3c298f89-4303-0410-b956-a3cf2f4a3e73
This could be used on NAND devices once we get UBI working.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42938 3c298f89-4303-0410-b956-a3cf2f4a3e73
This will allow us to add proper support for NAND one day.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42937 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change configures grub to mount the rootfs by PARTUUID instead of the
device path if CONFIG_TARGET_ROOTFS_PARTNAME is unset.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42936 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.
Signed-off-by: Josef Gajdusek <atx@atx.name>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42922 3c298f89-4303-0410-b956-a3cf2f4a3e73
The installation process on nand-based boards using ubi
like the BTHOMEHUBV2B makes use of a ramdisk image, so it
makes sense to generate this by default.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42920 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently JFFS2 end-of-filesystem marker 0xdeadc0de is included the
computation of image's MD5 checksum as part of the seama header. But
OpenWrt will erase blocks including and after the marker thus
invalidating the checksum after the first boot.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42915 3c298f89-4303-0410-b956-a3cf2f4a3e73
Qihoo C301 has 2 flash chips of which one is used as primary and the
other is used as backup. OEM U-Boot will try to boot an activeregion N
with imageNstatus=0 and imageNtrynum <= imagemaxtry. If such a region
is found, bootloader will try to increment imageNtrynum and boot it.
This patch tries to reset imageNtrynum after each successful boot (if
the boot process reaches the execution of /etc/init.d/done).
root@OpenWrt:/# hexdump -C -n 128 /dev/mtdblock9
00000000 9e f3 63 91 61 63 74 69 76 65 72 65 67 69 6f 6e |..c.activeregion|
00000010 3d 31 00 69 6d 61 67 65 31 73 74 61 74 75 73 3d |=1.image1status=|
00000020 30 00 69 6d 61 67 65 32 73 74 61 74 75 73 3d 30 |0.image2status=0|
00000030 00 69 6d 61 67 65 32 74 72 79 6e 75 6d 3d 30 00 |.image2trynum=0.|
00000040 69 6d 61 67 65 6d 61 78 74 72 79 3d 33 00 69 6d |imagemaxtry=3.im|
00000050 61 67 65 31 74 72 79 6e 75 6d 3d 30 00 00 00 00 |age1trynum=0....|
00000060 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42914 3c298f89-4303-0410-b956-a3cf2f4a3e73
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42911 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch fixes LED definitions for the DRAGINO2 board.
1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42897 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change makes the profile of WDR4900 more consistent with other router
specific profiles.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42896 3c298f89-4303-0410-b956-a3cf2f4a3e73
This way we will get logs if case of hang/crash in bcma or related code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42894 3c298f89-4303-0410-b956-a3cf2f4a3e73
Error reported by buildbot:
Package kmod-at91-adc is missing dependencies for the following libraries:
input-core.ko
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42893 3c298f89-4303-0410-b956-a3cf2f4a3e73
7Links PX-4885 (clones) can also be purchased with 8MB flash.
Creating images for these routers, use dtsi for common part
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42892 3c298f89-4303-0410-b956-a3cf2f4a3e73
DT file doesn't include any GPIOs yet, but let's add it as we got some
interest in this device on IRC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42864 3c298f89-4303-0410-b956-a3cf2f4a3e73
Let's generate a simple TRX file as we can't get encrypted one.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42863 3c298f89-4303-0410-b956-a3cf2f4a3e73
This allows IPv6 to set up without IPv4 being up thus
IPv6-only or IPv6+DS-Lite working with the default config.
Signed-off-by: Steven Barth <steven@midlink.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42848 3c298f89-4303-0410-b956-a3cf2f4a3e73
Have gpio driver adopt irqdomain support so that there are
non-overlapping allocations of irq numbers mapped to gpio's.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42844 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch originally failed to combine INTA/B/C/D onto a single ARM CPU
interrupt. Instead, it mapped INTA/B/C and excluded D. This patch
corrects the issue by mapping all four interrupts to the single ARM CPU
interrupt. The original intent of the patch still holds as the newer PCB
take advantage of isolated interrupts. This fix only applies to older
PCB's that do not route INTA/B/C/D to unique external ARM CPU
interrupts.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42830 3c298f89-4303-0410-b956-a3cf2f4a3e73
also fixes a GPIO related regression from the upgrade to 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42829 3c298f89-4303-0410-b956-a3cf2f4a3e73
This will simplify removing it in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42828 3c298f89-4303-0410-b956-a3cf2f4a3e73
This board is EOL, we should not bother anymore with it.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42825 3c298f89-4303-0410-b956-a3cf2f4a3e73
Looks like the targets are Ubiquiti routers which don't come with any wireless cards.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42810 3c298f89-4303-0410-b956-a3cf2f4a3e73
the driver did not handle all states correctly causing a deadlock of the i2c hw block.
Signed-off-by: Ing.Michele Mogioni <michele.mogioni@unimc.it>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42807 3c298f89-4303-0410-b956-a3cf2f4a3e73
This enables dedicated "rootfs" splitter by default. We still keep
CONFIG_MTD_SPLIT_SQUASHFS_ROOT, so the old (built-in) splitter will be
used as a fallback in case of problems.
Once we decide the dedicated partitioner works stable, we should remove
the old one completely.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42805 3c298f89-4303-0410-b956-a3cf2f4a3e73
We want to remove that old (built-in) splitter at some point.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42804 3c298f89-4303-0410-b956-a3cf2f4a3e73
make the notify script aware of this.
https://dev.openwrt.org/ticket/18005
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42798 3c298f89-4303-0410-b956-a3cf2f4a3e73
[ ] conditions should use = instead of == for string equality.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42796 3c298f89-4303-0410-b956-a3cf2f4a3e73
All TP-LINK machine names begin with "TP-LINK", so there's no need to check for
more specific model names. This also allows adding new models like the Archer
series more easily.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42795 3c298f89-4303-0410-b956-a3cf2f4a3e73
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.
Signed-off-by: Ron Curry <wingspinner@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42785 3c298f89-4303-0410-b956-a3cf2f4a3e73
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".
Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42782 3c298f89-4303-0410-b956-a3cf2f4a3e73
The irq rewrite was accepted upstream.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42739 3c298f89-4303-0410-b956-a3cf2f4a3e73
It does not make sense to add some code and remove is 4 patches later.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42673 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now that ucidef_set_interface_raw() has been updated to take a protocol
argument, use that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42666 3c298f89-4303-0410-b956-a3cf2f4a3e73
This allows tagged and untagged traffic together on the same port on ar8327
switch devices.
I looked at the first attempt to do this in r40777 (ar71xx: Fix tagged+untagged
operation on AR8327N (#12181)). I also set the vlan and port egress policies
like that change. But I change vlan_tagged in an less intrusive way. The
tagged/untagged decision is now based on the following rules:
- if vid != pvid then traffic is always tagged
- if vid == pvid then vlan_tagged stores if the traffic should be tagged
Tested on TP-Link WDR-3600 (ar8327N).
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42653 3c298f89-4303-0410-b956-a3cf2f4a3e73
This moves ingress, egress policy and pvid decisions to setup_port methods.
They arenow device type dependent.
This allows policy changes on only one device type which is needed to allow
tagged + untagged operation on ar8327.
Tested on TP-LINK WDR-3600 (ar8327N).
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42652 3c298f89-4303-0410-b956-a3cf2f4a3e73
This makes TRX files more /compatible/ with firmware files (e.g. CHK).
This will allow us to put some TRX files in BIN_DIR if we need to.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42646 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without running fixtrx the image will not boot at the second time,
because the CRC the boot loader check is invalid at that time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42639 3c298f89-4303-0410-b956-a3cf2f4a3e73
Upstream bcma patch:
bcma: use separated function to initialize bus on SoC
was backported incompletely. I missed arch code change.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42603 3c298f89-4303-0410-b956-a3cf2f4a3e73
This missing option was found by the build bots.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42583 3c298f89-4303-0410-b956-a3cf2f4a3e73
fix inclusion of functions.sh in dsl_fs init script
without this, the following error is seen during build:
./etc/init.d/dsl_fs: line 4: /lib/functions.sh: No such file or directory
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42575 3c298f89-4303-0410-b956-a3cf2f4a3e73
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.
This patch adds its initial support.
v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42552 3c298f89-4303-0410-b956-a3cf2f4a3e73
This device actually has a 8250 serial with a shift of 0.
Tested this on a BCM4708.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42538 3c298f89-4303-0410-b956-a3cf2f4a3e73
We used separated patch for patches that were sent but not accepted yet.
It has changed now, so let's use the standard patch file for them.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42535 3c298f89-4303-0410-b956-a3cf2f4a3e73
CONFIG_BLK_DEV does not activate any functionality, but many code, but
makes it possible to activate other options. Deactivating this breaks
the build of kmod-zram.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42528 3c298f89-4303-0410-b956-a3cf2f4a3e73
These missing option were found by the build bots.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42527 3c298f89-4303-0410-b956-a3cf2f4a3e73
This series of patches ports back some fixes of the ad799x driver, which were
commited between 3.10 and 3.15.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42523 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove symbols that are now placed in the generic config.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42513 3c298f89-4303-0410-b956-a3cf2f4a3e73
Convert gpiolib realization to platform driver and move to the
appropriate subdirectory. Misc GPIO interrupt acknowledgement placed
to the MISC IRQ handler since in fact we can detect only one GPIO state
change.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42512 3c298f89-4303-0410-b956-a3cf2f4a3e73
Call generic_handle_irq() instead of do_IRQ() for chained interrupts,
remove XXX_NONE interrupts and call spurious_interrupt() when an interrupt
is unexpected.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42510 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rename config symbols to be consistent with other SoCs config symbols
supported by MIPS arch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42508 3c298f89-4303-0410-b956-a3cf2f4a3e73
Tested with AR2315, AR2316 and AR2317 SoCs, not tested with AR2318 but
changes seems correct: revision is one more than AR2317.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42507 3c298f89-4303-0410-b956-a3cf2f4a3e73
Convert the PCI controller support code to platform driver and move it to
appropriate subdirectory.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42506 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rename configuration symbol to be consistent with other MIPS machines.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42505 3c298f89-4303-0410-b956-a3cf2f4a3e73
It seems that the PCI controller does not support I/O ports, so remove
the ports range. Also correct the beginning of the memory range and its
size.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42503 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use __raw_{read,write}l accessors and use Abort interrupt to detect a
configuration space read/write errors. The second change improves errors
detection, what improves the device presence detection and helps us to
avoid following (and similar) errors:
pci 0000:00:00.2: ignoring class 0x7e0200 (doesn't match header type 02)
pci 0000:00:00.2: bridge configuration invalid ([bus 03-90]), reconfiguring
pci 0000:00:00.2: not setting up bridge for bus 0000:01
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42502 3c298f89-4303-0410-b956-a3cf2f4a3e73
Explicitly configure PCI host controller, and do not expose it to PCI
subsystem. The PCI host controller acts as a usual PCI device connected
to the bus, but its configuration as a usual PCI device is senseless,
since the host controller provide access to _internal_ memory space for
_external_ device.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42500 3c298f89-4303-0410-b956-a3cf2f4a3e73
- add comment, which briefly describes PCI controller features and
Fonera 2.0g schematics.
- rename several functions and structures, to make it clear that this
code only for AR2315 chips.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42499 3c298f89-4303-0410-b956-a3cf2f4a3e73
Caller (generic PCI code) already do proper locking so no need to add
another one here.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42498 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove options which already selected by ATHEROS_AR231X on which
ATHEROS_AR2315 depends.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42497 3c298f89-4303-0410-b956-a3cf2f4a3e73
- use ether_foo() routines to work with addresses
- use ETH_ALEN inplace of magic '6'
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42494 3c298f89-4303-0410-b956-a3cf2f4a3e73
These IOCTLs handled in the core now.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42492 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use mutex inplace of spinlock to make code simple, also call
mutex_{lock,unlock} explicitly to avoid sparse warning about context
imbalance.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42491 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove FSF mailing address as suggested by checkpach and place license
URL.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42487 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make PCI IRQ handler and several structures static as suggested by
sparse.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42485 3c298f89-4303-0410-b956-a3cf2f4a3e73
Missing this headers cause several sparse "symbol 'foo' was not
declared. Should it be static?" warnings.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42483 3c298f89-4303-0410-b956-a3cf2f4a3e73
Avoid using of extern prototypes as suggested by checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42482 3c298f89-4303-0410-b956-a3cf2f4a3e73
Targets were build tested and patches are refreshed.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42463 3c298f89-4303-0410-b956-a3cf2f4a3e73
This switches to kernel 3.10 that was prepared by Hauke in r41531 :
gemini: add support for kernel 3.10
This is compile tested only, please run test and report back.
I've simply checked if it still compiles, unfortunately we didn't get
any feedback for this target.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42450 3c298f89-4303-0410-b956-a3cf2f4a3e73
It has been compile-tested only so far. Please give it a try.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42449 3c298f89-4303-0410-b956-a3cf2f4a3e73
the old dwc_otg driver is starting to fall apart and fails on newer 3g
modems and some storage devices. switch to the upstream dwc2 driver which
is no longer in staging/.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42446 3c298f89-4303-0410-b956-a3cf2f4a3e73
While the AR9331 has a gigabit MAC towards the internal switch, the
integrated PHYs however are only 100-base-tx capable. The existing code
however advertieses gigabit capability in the link status word. If you
attach such a PHY to a gigabit capable switch on the remote end, with
some probability it attempts to negotiate gigabit and fails, falling
baco to the AR9331 assuming a 10mbit half-duplex link. This has been
observed quite frequently with the Carambola2 and gigabit capable
switches.
In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
for both AR9331 ethernet ports. This is most likely wrong. Despite the
two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
100base-T PHY via MII. The has_gbit attribute is used in the ethernet
driver to determine the supported link modes.
So either pdata->has_gbit is not set to 1 anymore, or the ethernet
driver needs to be modified to determine the advertised link code word
on another criteria than pdata->has_gbit. This patch implements the
former solution.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42432 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some Kconfig options are only relevant for the legacy platforms, move
them where they belong
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42416 3c298f89-4303-0410-b956-a3cf2f4a3e73
We need a new kernel version to support Cortex-A5 based platforms such
as SAMA5GD3.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42415 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for Linux 3.14 for the Atmel's AT91 platform.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42414 3c298f89-4303-0410-b956-a3cf2f4a3e73
In preparation for adding 3.14 kernel support, move files and patches to
a separate per-version directory since some of them will have
incompatible changes (e.g: dts)
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42413 3c298f89-4303-0410-b956-a3cf2f4a3e73
In preparation for adding SAMA5D3 support, move the legacy ARMv5 based
platforms to a separate subtarget.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42408 3c298f89-4303-0410-b956-a3cf2f4a3e73
The cns3xxx uses irq61 for pcie0_intr which in the case of a PCIe-to-PCI
bridge ends up combining INTA/B/C/D on a single ARM CPU interrupt. This is
not optimal when you have multiple cores. To overcome this limitation an
enhancement was made on newer Laguna PCB's that support miniPCI cards
to route the INTA/B/C/D signals to unique external ARM CPU interrupts which
can help balance CPU core utilization and in some cases increase overall
system performance or responsiveness.
For more details see:
http://trac.gateworks.com/wiki/multicoreprocessing#PCIInterruptsteering
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42400 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patches are generated using the "format-patch" command from the
following location:
*https://www.codeaurora.org/cgit/quic/kernel/galak-msm/log/?h=apq_ipq_base
*rev=0771849495b4128cac2faf7d49c85c729fc48b20
Patches numbered 76/77/102/103 have already been integrated in 3.14.12,
so they're not in this list.
All these patches are either integrated are pending integration into
kernel.org, therefore these patches should go away once the kernel
gets upgraded to 3.16.
Support is currently limited to AP148 board but can be extended to other
platforms in the future.
These changes do not cover ethernet connectivity.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42334 3c298f89-4303-0410-b956-a3cf2f4a3e73
We were prompted for which DEBUG_LL_UART implementation we want, fix the
typos such that the build continues.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42332 3c298f89-4303-0410-b956-a3cf2f4a3e73
This improves performance when doing concurrent rx/tx on a single
ethernet MAC, e.g. when routing between VLANs.
Fixes#13072
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42328 3c298f89-4303-0410-b956-a3cf2f4a3e73
The bb-rc3 image for the BTHOMEHUBV2B is too big for its
mtd partition. This patch corrects the partition sizes in
the device tree. This patch should really go in before
bb-final, otherwise the BTHOMEHUBV2B images won't be useable.
I do apologise for not spotting this straight away.
Many thanks,
Ben
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42316 3c298f89-4303-0410-b956-a3cf2f4a3e73
A previous backported patch that adds freq/voltage operating points for the
IMX6DL processor can cause hang/crash (general instability) on IMX6DL
processors in the industrial/automative speed grades as they don't support
1GHz operation.
This adds another backported patch from mainline that uses IMX6 fuse settings
to properly remove invalid operating points for the particular CPU grade used.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42294 3c298f89-4303-0410-b956-a3cf2f4a3e73
the ohci phy was not reset properly
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42291 3c298f89-4303-0410-b956-a3cf2f4a3e73
the ohci phy was not reset properly
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42290 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are pretty many OpenWrt patches against mtd subsystem resulting
in a bit of mess and growing maintenance cost.
My idea is to use an extra "mtdsplit" directory with OpenWrt specific
files (including Kconfig).
This is the first step to achieve this. This patch adds a "mtdsplit"
directory with Kconfig and replaces 4 patches with a single one.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42287 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch enables the second SPI as spidev and also fixes some typos.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42277 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is based on Jon Smirl's patch with the following changes:
- Set CS polarity as low by default.
- Add support for changing CS polarity.
- Add support for changing LSB/MSB.
- Add support for changing SPI mode.
- Fix indentations.
I tested it on a VoCore. Works fine connected to a second flash, but fails to detect MMC/SD cards due to SPI clock speed.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42276 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes lots of sparse and checkpatch errors and extends the
documentation.
This also fixes a problem in the nvram parser, it now detects the
correct nvram on my Netgear R6250.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42272 3c298f89-4303-0410-b956-a3cf2f4a3e73
Upstream commit c11eede powerpc: add missing explicit OF includes for ppc was
included in 3.13 and onwards, hence making those patches obsolete.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42263 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes pflash registration through DT for 6338/6345/6348.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42235 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Felix Fietkau
Zoltan HERPAI
Hauke Mehrtens
Rafał Miłecki
Florian Fainelli
Jo-Philipp Wich
Steven Barth
Jonas Gorski
Luka Perkov
Nicolas Thill