Power LED is not active low, and ppp-fail is red, not green.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39294 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was not supposed to be committed, remove it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39293 3c298f89-4303-0410-b956-a3cf2f4a3e73
Enable the use of the USB gadget device at the board level so we can use
bcm63xx_udc on this board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39292 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also fixing a build warning due to a misplaced parenthesis in the
previous submission.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39291 3c298f89-4303-0410-b956-a3cf2f4a3e73
The wimax key will be used as a generic wwan key starting with Linux
3.13. The brcm47xx target uses this key for the 3g buttons. Also remove
the ifdef around KEY_WPS_BUTTON, this is in the kernel for a long time
now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39290 3c298f89-4303-0410-b956-a3cf2f4a3e73
This will select the correct dependencies also for more recent kernel versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39289 3c298f89-4303-0410-b956-a3cf2f4a3e73
Introduced by ("netifd: add wireless configuration support and port mac80211 to
the new framework")
Reported-by: René van Weert <r.vanweert@sowifi.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39288 3c298f89-4303-0410-b956-a3cf2f4a3e73
Very similar to the BCM96318REF board except for the name and the
SDRAM/DDR configuration which is totally transparent for us.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39286 3c298f89-4303-0410-b956-a3cf2f4a3e73
The devmem applet allows poking at HW registers and as such is a
valuable tool to have to avoid recompiling kernels or resorting to
external HW adapters to modify HW behavior.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39285 3c298f89-4303-0410-b956-a3cf2f4a3e73
BCM6318 support is usable enough to be enabled by default, turn it on.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39284 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add basic support for the BCM96318REF board which is comprised of:
- HS-SPI flash support
- Ethernet switch support
- USB slave device support
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39283 3c298f89-4303-0410-b956-a3cf2f4a3e73
Provide clock toggling for the USB host and slave controller as well as
for the Ethernet Switch. The bcm63xx_enetsw driver is changed not to use
request_mem_region() as the Roboswitch register overlaps with the
Roboswitch IUDMA channels, hence making the driver return -EBUSY. A
future fix might be to use variable size RSET_ENETSW sizes depending on
the chip we are targetting.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39282 3c298f89-4303-0410-b956-a3cf2f4a3e73
While adding support for BCM6345 Ethernet, some changes in the macros
ENETDMA{C,S} where introduced which now make the bcm63xx USB gadget
driver fail to build. Fix this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39279 3c298f89-4303-0410-b956-a3cf2f4a3e73
A missing condition check in dev-hsspi.c prevented the controller from
being registered on 6318 where it is fully functional.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39278 3c298f89-4303-0410-b956-a3cf2f4a3e73
varid might both unused and unitialized when building for e.g: bcm6318,
fix these two warnings turned into errors.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39277 3c298f89-4303-0410-b956-a3cf2f4a3e73
BCM63XX's ohci controller does not need the frame number shift, but that
was guarded with a PPC symbol. Fix this by making the no-fix generally
available.
This is a regression from the previous conversion to ohci platform driver.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39274 3c298f89-4303-0410-b956-a3cf2f4a3e73
CFE seems to leave the SPI flash mapping in an invalid state after
loading the kernel on some reference boards, so fix it up on boot.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39273 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add inital support for BCM6318, but keep it disabled for now until
most things are supported.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39272 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add initial support for the BCM63268 family of SoCs, but keep it
disabled for now as most things don't work yet.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39271 3c298f89-4303-0410-b956-a3cf2f4a3e73
The low PCIe window on BCM6328 and BCM6362 is actually only 1 MiB big,
not 16 MiB.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39270 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some SoCs have variants which are mostly the same, but use a different
chip id (or not). Add code for detecting them and handling them as
their standard counterparts.
This adds support for e.g. BCM6369.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39269 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the non runtime detect code since its effectiveness is dubious
and almost never used.
Also update affinity patches to work on top of it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39268 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update bmips cleanup patches with upstream submission and backport a few
bmips fixes.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39267 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes generic SPI flash accesses on BCM6358/BCM6368. BCM6338 still needs
additional fixes for M25P80, so it remains broken for now.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39266 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes e.g. SPI flash access on BCM6358/BCM6368. Transfers < 256 bytes
are not affected.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39265 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update the HSSPI driver with the upstream submitted one that has a
workaround for the auto cs down issue.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39264 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are no generic patches for kernel 3.7 any more, remove this stuff.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39262 3c298f89-4303-0410-b956-a3cf2f4a3e73
This driver will soon be removed completely and the scripts are already
using the new API.
This also removes bcm57xx_init() which restarts the switch and is now
done by b53.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39257 3c298f89-4303-0410-b956-a3cf2f4a3e73
Instead of looking into the proc entry provided by broadcom-diag use
the board info from /proc/cpuinfo to get the board we are on.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39256 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the new led api also on brcm47xx.
The led for failsafe indication is searched for.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39255 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the code used on the old switch driver.
The Ethernet drive is loaded as a module and needs some time to get up
therefor we added some wait function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39254 3c298f89-4303-0410-b956-a3cf2f4a3e73
This makes brcm47xx target use the default gpio led and button driver
and not broadcom-diag any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39253 3c298f89-4303-0410-b956-a3cf2f4a3e73
This backports some patches from linux upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39249 3c298f89-4303-0410-b956-a3cf2f4a3e73
This helps to avoid high order alloction failures.
Closes#14702.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39247 3c298f89-4303-0410-b956-a3cf2f4a3e73
Luka Perkov
Zoltan HERPAI
Florian Fainelli
Hauke Mehrtens
John Crispin
Jonas Gorski
Gabor Juhos