This patch adds support for the Omnima MiniPlug RT5350 based board, 8MB SPI flash
Signed-off-by: Ivan Ignjatic<ivan@omnima.co.uk>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42200 3c298f89-4303-0410-b956-a3cf2f4a3e73
Switch in Edimax 3G-6200n also require full switch reset, not only vlan definitions. Tested on Edimax 3G-6200n.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42194 3c298f89-4303-0410-b956-a3cf2f4a3e73
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42193 3c298f89-4303-0410-b956-a3cf2f4a3e73
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42184 3c298f89-4303-0410-b956-a3cf2f4a3e73
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42180 3c298f89-4303-0410-b956-a3cf2f4a3e73
Due to TCP connections not working when VLAN is disabled, this is
needed to get failsafe functional.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42179 3c298f89-4303-0410-b956-a3cf2f4a3e73
According to the pcb tracing results[1] by anton.rad[2] MPR-A1s expose
6 unused GPIOs, only one of them working as configured in the current
DTS. This patch enables GPIO22-26.
Tested on hardware.
[1] http://i.imgur.com/kHVW2Ox.jpg
[2] https://forum.openwrt.org/viewtopic.php?pid=222698#p222698
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42178 3c298f89-4303-0410-b956-a3cf2f4a3e73
The conversion was not 100% correct and leads to u-boot failing to
verify the CRC, revert that change for now.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42170 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch is causing more harm than good on most AR7 routers out there,
better have no manageable switch rather than no ethernet connection, at
least for now.
Fixes#16523, #5927
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42168 3c298f89-4303-0410-b956-a3cf2f4a3e73
we should check for ssb here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42164 3c298f89-4303-0410-b956-a3cf2f4a3e73
The GW5520 is a small form-factor single-board computer with the following
features:
* 70x100mm form-factor
* IMX6DL 800MHz SoC (IMX6Q optional)
* 512MB 32bit DDR3 SDRAM (up to 2GB optional)
* 256MB NAND FLASH (up to 2GB optional)
* Gateworks System Controller
* 2x front-panel Intel i210 GbE adapters with passive PoE support
* 2x MiniPCIe sockets with USB support
* 2x front-panel USB
* 1x rear-panel full-size HDMI connector
* 1x front-panel bi-color user LED
* 1x front-panel user pushbutton
* 1x rear-panel barrel jack for power
* 1x Application connector with:
* 2x TTL level UARTs
* 10x TTL level Digital IO
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42148 3c298f89-4303-0410-b956-a3cf2f4a3e73
The GW16083 Ethernet Expansion Mezzanine adds the following to supported
Gateworks baseboards:
* 7-port Ethernet Switch
* 4x RJ45 ports (ENET1-4) supporing 802.11af/at PoE (with optional PoE module)
* 2x RJ45 ports or SFP module (ENET5-6) (auto-selected)
This series adds support for a phy driver that adds support for ENET5/ENET6
PHY adding initialization for those PHY's and a polling mechanism that detects
SFP insertion and configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42147 3c298f89-4303-0410-b956-a3cf2f4a3e73
The GW16082 miniPCI Expansion Mezzanine has the INTA/B/C/D IRQ's reversed
from the PCI standard. This will soon be resolved in the bootloader via
devicetree, but in the meantime this will work around the issue.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42146 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now it is possible to use b43 wifi.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42143 3c298f89-4303-0410-b956-a3cf2f4a3e73
bcma does not support this card and b43 hangs when probing this card.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42142 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now that we migrated all users to dtb based detection, we can drop the
board fixup code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42129 3c298f89-4303-0410-b956-a3cf2f4a3e73
This splits up neufbox 4 for now into two images, one for each OEM.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42128 3c298f89-4303-0410-b956-a3cf2f4a3e73
This requires individual images for each board version for now.
Linux partition was shrunk to ensure writing thewrong image won't
erase wifi calibration data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42126 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use appended dtb for board detection for bcm96328avng.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42124 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add the required nodes to the dtsi files and code to prevent double
registration from the board support code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42123 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a helper for building images with dtb appended kernels.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42122 3c298f89-4303-0410-b956-a3cf2f4a3e73
In preparation for switching to dtb based board identification, add
support for building lzma-loader and lzma cfe kernels with dtb
appended.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42121 3c298f89-4303-0410-b956-a3cf2f4a3e73
Allow appending a dtb blob to the binary and use it for identifying the
board. Fall back to nvram based identification in case of no dtb passed.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42119 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make it less likely for quilt/patch to put boards into the "wrong"
section.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42117 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42088 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42083 3c298f89-4303-0410-b956-a3cf2f4a3e73
This allows dynamic voltage and frequency scaling to work for IMX6DL CPU's.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42072 3c298f89-4303-0410-b956-a3cf2f4a3e73
In r41578 this was added in order to make default images bootable for the BB
release. We need more generic approach for this.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42071 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is still not working.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42054 3c298f89-4303-0410-b956-a3cf2f4a3e73
Apparently this is a fairly common refurb unit of the 3800 series now,
with merely the recognition string changed in the boot loader.
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42023 3c298f89-4303-0410-b956-a3cf2f4a3e73
This changeset implements a new menuconfig option to generate separate
repositories for each enabled package feed instead of one monolithic one.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42002 3c298f89-4303-0410-b956-a3cf2f4a3e73
After several tests, 3.14 kernel seems run fine.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41997 3c298f89-4303-0410-b956-a3cf2f4a3e73
Created on basis of 3.10 config. Remove few obsolete symbols and add new
upstream symbols. New symbols left in its default state.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41996 3c298f89-4303-0410-b956-a3cf2f4a3e73
Change list:
* Remove button info on GPIO12, there is no button there.
* Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.
Tested building for carambola2 target.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41993 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix IFF_NO_IP_ALIGN location which is collide with new netdev private flag
IFF_MACVLAN.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41992 3c298f89-4303-0410-b956-a3cf2f4a3e73
Lenovo AC1200 series has two types, Y1 and Y1S.
Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port.
Signed-off-by: Lintel <lintel.huang@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41961 3c298f89-4303-0410-b956-a3cf2f4a3e73
This commit implements a new netfilter match "xt_id" which can be used to
attach unsigned 32bit IDs to iptables rules.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41945 3c298f89-4303-0410-b956-a3cf2f4a3e73
Mostly works except for USB led. Flashing not tested yet. Mostly
as an example for the sprom fixup code.
Fixup values taken from GPL tarball by comparing bcm43217_map.c
with the struct in sprom.c.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41944 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rework fallback sprom support by providing different sproms for
different chips. Also make it optional to use.
This likely causes sprom fallback support to break on a few boards.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41942 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now that BB is branched off, we can now switch to 3.14 and start
breaking stuff again.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41941 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a working lzma loader and use it for generating initramfs kernels
to allow easily netbooting elf kernels on devices with a 4 MiB CFE
size limit.
Based on ar71xx's lzma-loader.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41940 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41939 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for setting SPI_CS1 as Chip Select, Watchdog reset output and GPIO#27.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41938 3c298f89-4303-0410-b956-a3cf2f4a3e73
LED Fix up for the Kingston Mobilelite Wireless (MLW-221)
http://wiki.openwrt.org/toh/kingston/mlw221
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41933 3c298f89-4303-0410-b956-a3cf2f4a3e73
this caused factory resets when reboot was pressed
Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41932 3c298f89-4303-0410-b956-a3cf2f4a3e73
without this the build for NBG6716 fails due to missing packages
https://dev.openwrt.org/ticket/17325
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41930 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use kernel 3.14 by default and refresh the patches
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41913 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is a backport of bcma from wireless-tesing/master tag master-2014-07-29-1.
For kernel < 3.10 this only adds the header changes needed by more
recent b43 versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41899 3c298f89-4303-0410-b956-a3cf2f4a3e73
ath9k failed to come up due to a bad mac addr
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41860 3c298f89-4303-0410-b956-a3cf2f4a3e73
This appears to be a typo.
Signed-off-by: Russell Senior <russell@personaltelco.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41859 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix a typo: gpio 21 is already used for the WPS led. Gpio 20 is the
right one (tested) for the mode switch. Confirmed that
/sys/kernel/debug/gpio state followed the position of the switch.
Signed-off-by: Russell Senior <russell@personaltelco.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41858 3c298f89-4303-0410-b956-a3cf2f4a3e73
Follows the pattern of http://patchwork.openwrt.org/patch/5970/
Signed-off-by: Russell Senior <russell@personaltelco.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41857 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since kernel commit 928bea964827 ("PCI: Delay enabling bridges until
they're needed"), pci fixups are run with bridges (e.g. the pcie port)
disabled.
This causses hangs when ath9k_pci_fixup tries to manually enable the
device to apply the register fixups.
Fix this by enabling any parent bridges before trying to access the
device itself.
Fixes boot on DSL-274XB rev F1.
Reported-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41856 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Kingston Mobilelite Wireless (MLW-221)
http://wiki.openwrt.org/toh/kingston/mlw221
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41841 3c298f89-4303-0410-b956-a3cf2f4a3e73
Compile tested all subtargets and profiles.
Unfortunately I don't own any board affected by these changes, so no run tests.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41839 3c298f89-4303-0410-b956-a3cf2f4a3e73
The earlier r41797 change was missing this part, to enable the right
vlan configuration.
Signed-off-by: Russell Senior <russell@personaltelco.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41838 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since the earlier r41797 change, the board_name for awm003 has been
miscalculated, and sysupgrade has been broken. This seems to fix it.
Signed-off-by: Russell Senior <russell@personaltelco.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41837 3c298f89-4303-0410-b956-a3cf2f4a3e73
It doesn't seem to be used anywhere, it's incompatible with other
targets and can be confusing. People may think they need to update
section name every time they change VLAN ID (well, even I was doing
that).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41835 3c298f89-4303-0410-b956-a3cf2f4a3e73
kernel 3.6 is not used by any target any more, remove it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41834 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is a backport of bcma and ssb from wireless-tesing/master tag
master-2014-07-22.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41804 3c298f89-4303-0410-b956-a3cf2f4a3e73
same as AWM002 but with 64mb RAM
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41797 3c298f89-4303-0410-b956-a3cf2f4a3e73
Changeset 38690 broke the WAN MAC setup. Here's the fix.
Signed-off-by: Sebastian Kemper <sebastian_ml <at> gmx.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41795 3c298f89-4303-0410-b956-a3cf2f4a3e73
The airGateway has a reset button connected to GPIO 12, so we should use it.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41794 3c298f89-4303-0410-b956-a3cf2f4a3e73
LED script expects WLAN LED to be "gl-connect:red:wlan".
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41793 3c298f89-4303-0410-b956-a3cf2f4a3e73
ASL-26555 16MB: caldata is present on uboot-env and devdata, but the proper one seems to be the devdata, since mac address corresponds to Amper, the real manufacturer, meanwhile the caldata on uboot-env corresponds to D-Link.
ASL-26555 8MB: caldata is only present on uboot-env, but its mac address corresponds to Alpha, the real manufacturer.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41768 3c298f89-4303-0410-b956-a3cf2f4a3e73
The default case in 02_network is inappropriate for the MikroTik RouterBOARD 91x boards because they do not have a WAN port, so don't bother setting the non-existent eth1 interface as the WAN port.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41767 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Ubiquiti Networks airGateway.
Based in part on code posted by David Hutchison <dhutchison@bluemesh.net> on openwrt-devel:
https://lists.openwrt.org/pipermail/openwrt-devel/2013-December/023035.html
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41766 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update the kernel of the orion target to version 3.10.44.
Refresh orion config and patches to match the changes in the kernel
Tested on WRT350N-v2 device.
Signed-off-by: Maarten Bezemer <maarten.bezemer@gmail.com>
[run make kernel_oldconfig, fold a01-dt2-fixes-for-3.3.patch into dt2-setup.c,
make dt2-setup.c compile, fix harddisk subprofile]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41765 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is compile tested only, please run test and report back.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41737 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is compile tested only, please run test and report back.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41736 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes error erasing partial mtd partition which does not start on
eraseblock boundary and allows using fconfig to configure redboot on
devices such as the Gateworks Cambria.
Signed-off-by: Maciej Skrzypek <maciej.skrzypek@flytronic.pl>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41733 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use AR2315_ prefix for macroses specific to AR2315/AR2316/AR2317 chips,
use AR5312_ prefix for macroses specific to AR5312/AR2312/AR2313 chips,
and use AR231X_ prefix for common macroses.
This patch should not cause any functional changes, only make clear
which macros is common and which macros is specific.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41701 3c298f89-4303-0410-b956-a3cf2f4a3e73
Pass only physical address to 8250 serial port driver and set flag to
remap I/O memory inside the driver. Also fix AR5312 UART base address
definition, which seems specified already mapped.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41700 3c298f89-4303-0410-b956-a3cf2f4a3e73
Pass PHY I/O memory region via platform resources and remap them
unconditionally.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41698 3c298f89-4303-0410-b956-a3cf2f4a3e73
Each SoCs generation has own independent gpiolib realization, so we
have no reason to keep these realizations in semiuniversal form.
Following modifications are made:
* Remove valid_mask field
* Remove ar231x_gpio_chip structure
* Rename AR2315_GPIO_CR to AR2315_GPIO_DIR
* Fix count of AR5312 GPIOs
* Simplify gpio_chip methods realization
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41696 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently AR5312 misc IRQ numbers are used for AR2315+ chips, what cause
us to use switch-case to map IRQ number to ISR bit. Introduce AR2315
specific misc IRQs set and simplify interrupt (un)mask operation.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41694 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rename interrupt control handlers to be consistent with operation names
and add IRQ chips names.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41693 3c298f89-4303-0410-b956-a3cf2f4a3e73
UART IRQ number could be different for different SoCs, so make them
configurable.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41691 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Pass iomem and IRQ via platform device resources
* Remap iomem and use iowrite32 accessor function
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41688 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rename config symbol to AR2315_WDT to avoid confusion with other Atheros
SoCs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41685 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Florian Fainelli
Hauke Mehrtens
Luka Perkov
Imre Kaloz
Jonas Gorski
Jo-Philipp Wich
Felix Fietkau
Steven Barth
Zoltan HERPAI
