This chipset has at least 8 usable ports, e.g. Netgear R8000 has ports
5, 7 and 8 connected to Ethernet interfaces:
vlan1ports=0 1 2 3 5 7 8*
vlan2ports=4 8u
Port 6 seems to be always disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45676 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since the kernel/rootfs split handling was modified 2 years ago by r37283 (
https://dev.openwrt.org/changeset/37283 ) and by the subsequent checkins,
users have seen rather scary mtd errors in the log at every boot. The message
ends "-- forcing read-only", which looks a bit error-like. That error has
been mentioned in some forum threads, when users have noticed this message
instead of some actual error.
[ 2.940000] 0x000000070000-0x000000ff0000 : "firmware"
[ 2.970000] 2 netgear-fw partitions found on MTD device firmware
[ 2.970000] 0x000000070000-0x000000188440 : "kernel"
[ 2.980000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 2.990000] 0x000000188440-0x000000ff0000 : "rootfs"
The patch removes the rather useless warning message.
signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45669 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change adds PCIe support to IPQ806x based platforms. The driver is
actually cherry-picked from the following LKML thread:
*https://lwn.net/Articles/643086/ (patches 110-111)
We also add here an additional fix to support multiple PCI controllers
on the same platform (patch 112), and to patch the ap148 & dbs149 DTS
files (patch 113).
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45663 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change enable zImage+appended dtb support in ipq806x kernel
options. The zImage will now be generated as part of the kernel
binaries. Platforms which do not have DT support enabled in U-boot
can now make use of it by generating zImage files and appending dtb
to it.
It is not used yet but it is done as a stepping stone for early IPQ806x
platforms, which did not include DT support in U-boot.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45662 3c298f89-4303-0410-b956-a3cf2f4a3e73
ARCH_QCOM is using the ARCH_MULTIPLATFORM option, as now recommended
on most ARM architectures. This automatically calculate ZRELADDR by
masking PHYS_OFFSET with 0xf8000000.
On IPQ806x though, the first ~20MB of RAM is reserved for the hardware.
In newer bootloader, when DT is used, this is not a problem, we just
reserve this memory in the device tree. But if the bootloader doesn't
have DT support, then ATAGS have to be used. In this case, the ARM
decompressor will position the kernel in this low mem, which will not be
in the RAM section mapped by the bootloader, which means the kernel will
freeze in the middle of the boot process trying to map the memory.
As a work around, this patch allows disabling AUTO_ZRELADDR when
ARCH_QCOM is selected. It makes the zImage usage possible on bootloaders
which don't support device-tree, which is the case on certain early
IPQ806x based designs.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45661 3c298f89-4303-0410-b956-a3cf2f4a3e73
This option has been added in kernel 3.17. It shows-up only when both
ARCH_QCOM and CRYPTO are enabled. So we'll disable these two by default
to avoid stalling the build when these conditions are met.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45658 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add Support for the Seagate GoflexHome <http://wiki.openwrt.org/toh/seagate/goflexhome>
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45647 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are 2 images missing: TLWR2543 TLWR1043V2 which have special properties.
v2: set correct DEVICE_PROFILES for all images.
v2: migrate TP-LINK TL-WR710N v2 which was committed after v1.
v2: split very very long line `TARGET_DEVICES +=` into smaller parts
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45643 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45640 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45639 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45638 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45637 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45636 3c298f89-4303-0410-b956-a3cf2f4a3e73
Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45635 3c298f89-4303-0410-b956-a3cf2f4a3e73
Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45634 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861
I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
2) must init GMAC0 before GMAC1
That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.
An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.
2) Possible consequence of no longer explicitly setting ethernet duplex/speed.
Review: With this patch, my ethernet and wireless works.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45633 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45632 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45631 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45630 3c298f89-4303-0410-b956-a3cf2f4a3e73
It has been broken since the new ath10k firmware introduced in r44656.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45624 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also refresh one patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45601 3c298f89-4303-0410-b956-a3cf2f4a3e73
This also changes the MAC address to one of the adresses actually used by the
stock firmware on one of the ethernet interfaces.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45599 3c298f89-4303-0410-b956-a3cf2f4a3e73
This will make these files much more maintainable.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45597 3c298f89-4303-0410-b956-a3cf2f4a3e73
Moved board to the right magic case.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45588 3c298f89-4303-0410-b956-a3cf2f4a3e73
INET_LRO deprecated and there are exactly two drivers using it, neither
being included in any of the targets enabling INET_LRO. At the same time
both drivers needing it select it.
So just disable it for everyone.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45584 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was a remnant of an old version.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45583 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some devices have unsorted ports which may lead to broken config.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45575 3c298f89-4303-0410-b956-a3cf2f4a3e73
I still need to test following patch before backporting:
bgmac: leave interrupts disabled as long as there is work to do
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45571 3c298f89-4303-0410-b956-a3cf2f4a3e73
Linux 4.0 was released on 2014-04-12
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45559 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix the led naming and gpios.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45558 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hopefully the last missing board.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45557 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the XW version of the Rocket M series devices
manufactured by Ubiquiti, based on the Atheros AR9342 SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45553 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are some rare devices without NAND, like Netgear EX6200 or
TP-LINK Archer C8.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45545 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is needed as prepare_generic_squashfs generates more data (in our
case 0x40004 B) and it's complex for sysupgrade to extract UBI image out
of TRX.
Signed-off-by: Dan Haab <dhaab@luxul.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45541 3c298f89-4303-0410-b956-a3cf2f4a3e73
TP-Link TL-WR710n v2 looks like v1, but has less memory (4MB).
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45538 3c298f89-4303-0410-b956-a3cf2f4a3e73
DB149 is a IPQ8064 based platform. This patch adds the init scripts to
detect it, configure the network accordingly, and generate a flashable
image for it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45537 3c298f89-4303-0410-b956-a3cf2f4a3e73
DB149 is an IPQ806x based development platform. This patch adds the dts
files to support it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45536 3c298f89-4303-0410-b956-a3cf2f4a3e73
Certain IPQ806x based platforms are making use of this PHY. So we'll
enable it so it gets detected as such.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45535 3c298f89-4303-0410-b956-a3cf2f4a3e73
-removed symbol because it should be handled by wpan.mk
-add missing FAKEHARD symbol (this symbol is removed in Kernel 4.0)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45530 3c298f89-4303-0410-b956-a3cf2f4a3e73
It was reported that OM5P-AN needs not only a delay setting of 1 for RXD/RDV
but 2. These was found when testing with a NetGear GS752TP POE switch with a
cable length of 50ft and 250ft.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45524 3c298f89-4303-0410-b956-a3cf2f4a3e73
The ETH_RXDV_DELAY (17:16) and ETH_RXD_DELAY (15:14) are currently not cleared
by the function ath79_setup_ar934x_eth_cfg. Clearing these in the
ath79_setup_ar934x_eth_cfg may cause problems on some hardware because they
rely on the preset value by the bootloader.
Instead another function is introduced which also works on ETH_CFG on AR934x.
It can be used to safely clear and set ETH_RXDV_DELAY and ETH_RXD_DELAY on
machines which require special settings.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45523 3c298f89-4303-0410-b956-a3cf2f4a3e73
The commit r38948 ("ag71xx: add F1E specific feature bit definitions to AR934X
register file") introduced definitions for some bits in the RDV/RXD part of the
ETH_CFG register of AR934x. These are incomplete because ETH_RXDV_DELAY is
specified as 17:16 and ETH_RXD_DELAY is specified 15:14. The original commit
only specified the lower bits. The upper bits also have to be unset when the
lower bits should only be set.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45522 3c298f89-4303-0410-b956-a3cf2f4a3e73
The tx/rx delay bits in the ETH_XMII_CONTROL register have to be unset when the
enable_rgmii_rx_delay/enable_rgmii_tx_delay will be set in the AT803x PHY.
Othwise the throughput in gigabit mode is heavily reduced.
Signed-off-by: Sven Eckelmann <sven@open-mesh.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45521 3c298f89-4303-0410-b956-a3cf2f4a3e73
Profile definitions need to be checked and fixed before this patch can
be applied again.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45511 3c298f89-4303-0410-b956-a3cf2f4a3e73
Refresh patches to remove the trailing whitespaces caused by an old
diffutils version on osx.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45506 3c298f89-4303-0410-b956-a3cf2f4a3e73
This should rather be done by passing appropriate platform_data/OF, but
should suffice for now.
Fixes e.g. GbE ports on BCM963268BU_P300.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45505 3c298f89-4303-0410-b956-a3cf2f4a3e73
At least the third rgmii port is available on 63169, so assume all are
available. Simplifies cpu vs. variant handling.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45504 3c298f89-4303-0410-b956-a3cf2f4a3e73
The new building code included the rootfs twice when building tplink initramfs images.
To make it more readable move initramfs into an own build step
Build/mktplinkfw-initramfs.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45491 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are 2 images missing: TLWR2543 TLWR1043V2 which have special properties
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45490 3c298f89-4303-0410-b956-a3cf2f4a3e73
The new image size is verified by a running tplink device and checked
against mktplinkfw source code.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45488 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rafał Miłecki
Felix Fietkau
Luka Perkov
Imre Kaloz
Jonas Gorski
Florian Fainelli
John Crispin
Jo-Philipp Wich