According to the ticket #18152 it also uses NAND with 0x20000 erase size
and 0x800 page size.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43008 3c298f89-4303-0410-b956-a3cf2f4a3e73
The wpa_psk_file option offers the possibility to use a different WPA-PSK key for each client. The directive points to a file with the following syntax:
mac_address wpa_passphrase_or_hex_key
Example:
00:11:22:33:44:55 passphrase_for_client_1
00:11:22:33:44:67 passphrase_for_client_2
00:11:22:33:44:89 0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef
So it is possible to specify both ASCII passphrases and raw 64-chars hex keys.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43001 3c298f89-4303-0410-b956-a3cf2f4a3e73
the submitted patch was bogus
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42994 3c298f89-4303-0410-b956-a3cf2f4a3e73
Only support Linux at the moment.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42988 3c298f89-4303-0410-b956-a3cf2f4a3e73
[base-files] failsafe-mode: print short help on commandline
Like mentioned in ticket https://dev.openwrt.org/ticket/11911
this should make the IRC much quieter. Failsafe is somehow
special and even experienced users are helpless, because they
are not used to this seldom situation. Also: likely you have
no internet access in this mode, so you cannot use the wiki.
a failsafe-session now looks like this:
first we see from 'package/base-files/files/bin/login.sh' the hint:
=== IMPORTANT ============================
Use 'passwd' to set your login password
this will disable telnet and enable SSH
------------------------------------------
after this the /etc/banner ("OpenWrt - wireless freedom")
and then the new text:
================= FAILSAFE MODE active ================
special commands:
* firstboot reset settings to factory defaults
* mount_root mount root-partition with config files
after mount_root:
* passwd change root's password
* /etc/config directory with config files
for more help see:
http://wiki.openwrt.org/doc/howto/generic.failsafe
=======================================================
this supersedes the old patches:
http://patchwork.openwrt.org/patch/3337/http://patchwork.openwrt.org/patch/3553/
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42985 3c298f89-4303-0410-b956-a3cf2f4a3e73
SENSORS_VEXPRESS is masked by HWMON
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42984 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix sysupgrade to determine the correct boot block device to use if
/proc/cmdline contains a PARTUUID root.
Change the preinit move_config() hook to use the UUID scanning code
from sysupgrade in order to avoid code duplication.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42968 3c298f89-4303-0410-b956-a3cf2f4a3e73
Enable the required squashfs and block2mtd support in the kernel in order
to be able to actually boot them.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42967 3c298f89-4303-0410-b956-a3cf2f4a3e73
If the underlying block device is a USB device it might require some
time to settle, observed when booting a squashfs image from sd card
on an Alix APU board.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42966 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Makefile for binutils creates a broken symlink to "binutils-linaro" in
"trunk/build_dir/toolchain-<target>_gcc-4.9-linaro_uClibc-0.9.33.2".
Modify the Makefile to point the symlink to the correct directory.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42954 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rafał Miłecki
Felix Fietkau
John Crispin
Imre Kaloz
Jo-Philipp Wich