In mtd_verify(), the return value of md5sum() has been
interpreted as error if nonzero, while the function
returns number of processed bytes, which caused
mtd_verify() to always fail.
This patch fixes error checking to interpret only
negative values as errors.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44605 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now bcma provides IRQ domain we don't have to poll anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44596 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes several issues in the network stack.
Full changelog:
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.8
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44593 3c298f89-4303-0410-b956-a3cf2f4a3e73
Tested by Jonas on WP54g, thank you!
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44588 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most devices have only 16 MiB of RAM, this will allow them to boot
without OOM.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44587 3c298f89-4303-0410-b956-a3cf2f4a3e73
The driver code for supporting these subtargets was already removed a while ago,
so
the current images wont actually boot.
It is also quite unlikely that there are any users of them at this point, so
remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44586 3c298f89-4303-0410-b956-a3cf2f4a3e73
The flag is experimental and requires toolchain support, which we don't
provide. Also neither target has an FPU so it becomes meaningless
without the FPU emulator enabled.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44584 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44583 3c298f89-4303-0410-b956-a3cf2f4a3e73
Saves us pulling in the input system, shaving off a few kb from image
sizes.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44582 3c298f89-4303-0410-b956-a3cf2f4a3e73
Linux commit d75b1ade567ffab ("net: less interrupt masking in NAPI")
chose the samantics of the napi poll return value, which caused napi to
not resume interrups/polling anymore.
Fix the return value to restore expected behaviour.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44576 3c298f89-4303-0410-b956-a3cf2f4a3e73
Legacy probe passed the IRQSTAT registers instead of the IRQMASK
registers causing all register accesses to be offset by 16 bytes.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44575 3c298f89-4303-0410-b956-a3cf2f4a3e73
The driver expected data then dir, but both dts and legacy code passed
dir then data. Fix this by making the driver expect the registers in
ascending order, i.e. dir then data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44574 3c298f89-4303-0410-b956-a3cf2f4a3e73
For bcm63xx integrated switches, broadcom changed the data endianess
to match the system endianess. But this only applies to within one word,
which causes 48/64 bit values to be still split into their "litte endian"
groups.
E.g. 48 bit values (with 5 being the most significant byte) aligned
0x00 ..01 or 0123
0x04 2345 45..
will become
0x00 ..10 resp. 3210
0x04 5432 54..
Likewise for 64 bit values.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44568 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now that all gpio users without named gpios use DT, we do not need
to fix the gpio controller bases anymore.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44567 3c298f89-4303-0410-b956-a3cf2f4a3e73
Register buttons and leds through DT for all available dts,
and remove them from the board files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: remove leds/buttons from board files
fix wrong led polarities for dsl-274xb-c2, cpva642, p870hw
comment out spi-gpio and associated leds]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44566 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a generic mmio gpio controller based driver and probe it
through device tree.
Use aliases for base calculation until we converted all users to
device tree or named gpios.
Convert bcm63xx_enet's ephy-reset gpio to use a named gpio.
While at it, remove the duplicate reset gpio defintion for livebox.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44565 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a dtsi for bcm3368, add a dts and profile for cvg834g, and convert
it to use ImageDTB. Since HCS requires more arguments, enhance the max
arguments of the call.
The image name is intentionally left blank to prevent non-initramfs
images to be built, as they currently contain no rootfs and consequently
won't work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44561 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most 16 MiB RAM devices don't even load elf kernels, so it's safe to
assume we have at least 32 MB RAM. This fixes tftp booting with the
default package set as this already produces an uncompressed
kernel > 8 MiB.
New limit is 8 MiB compressed / 24 MiB compressed.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44558 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the need for the header file to be exported - we don't need most
of it anyway; all we care about are the offset of the rootfs length and
header crc fields.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44557 3c298f89-4303-0410-b956-a3cf2f4a3e73
We do not need to align the start of read only rootfs's to erase blocks.
This allows us to write the squashfs rootfs directly behind the kernel,
potentially freeing up one erase block.
We still need to align for jffs2, so add a flag for imagetag to
optionally align the rootfs start.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44556 3c298f89-4303-0410-b956-a3cf2f4a3e73
We do not use the result, so no need to call it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44555 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Rafał Miłecki
Jonas Gorski
Felix Fietkau
Michael Büsch
Lars-Peter Clausen
Jo-Philipp Wich