Thanks to Jonas Gorski for the help.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35567 3c298f89-4303-0410-b956-a3cf2f4a3e73
Accessing the AR8xxx switches via the name of the
attached ethernet device is not possible since
r35560. Change the uci-defaults script to use
switchX names in switch configurations.
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35561 3c298f89-4303-0410-b956-a3cf2f4a3e73
A small cosmetic fix to show the HW model name correctly in LuCI.
Patch-by: Amir Sagie <openwrt-devel@taproot.org.il>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35365 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also fix the default network configuration
according to the new setup.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34854 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will be used on other boards as well.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34234 3c298f89-4303-0410-b956-a3cf2f4a3e73
The original TP-Link firmware images can be flashed via
the sysupgrade command, however those may contain a
bootloader. Flashing such an image via sysupgrade
bricks the board, and it can't be recovered without
a serial console.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33944 3c298f89-4303-0410-b956-a3cf2f4a3e73
With these images, it is possible to use the 'unused'
partition of the flash. The 'fat' images can be installed
with the sysupgrade command. When a 'fat' image is
installed from a regular one, the platform specific
sysupgrade script copies the calibration data to the
end of the flash. Likewise, when a regular image is
installed from the 'fat' version the sysupgrade script
copies the calibration data back to the original location.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33540 3c298f89-4303-0410-b956-a3cf2f4a3e73
It should be implemmented in a cleaner way.
This reverts the following commits:
[ar71xx] dir-825-b1: Fix wholeflash images
[ar71xx] dir825b1: Add image for DIR-825-B1 that uses the whole flash"
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33459 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds preliminary support for the Mikrotik RB2011L.
The NAND flash is not yet supported, so only the initramfs
kernel can be used for now.
[juhosg: remove unnecessary PCI/USB related stuff, the board
does not use that, update commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33344 3c298f89-4303-0410-b956-a3cf2f4a3e73
An improved LED support for Buffalo WZR-HP-AG300H.
There will be two new packages to go with this patch
(ar922x-led-fix-hotplug and ar922x-led-fix-init).
These packages essentially perform the same task of
disabling "JTAG over GPIO pins" function which is
currently required for LEDs on AR922x emac GPIO to work,
and are both considered a temporary fix that circumvent
this problem.
[juhosg: add the hotplug script from the proposed
ar922x-led-fix-hotplug package to ar71xx/base-files]
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33294 3c298f89-4303-0410-b956-a3cf2f4a3e73
For the pure convenience of having a correctly named
image and system name in /proc/cpuinfo , until we can
do that by having system names in DTS...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33224 3c298f89-4303-0410-b956-a3cf2f4a3e73
The TL-WDR3600 is identical to the TL-WDR4300 with the exception that is has
only two antennas.
[juhosg: remove the custom machine type, change the board name instead]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33219 3c298f89-4303-0410-b956-a3cf2f4a3e73
Here is the uci-defaults version of the led support for
the Buffalo WLAE-AG300N.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32932 3c298f89-4303-0410-b956-a3cf2f4a3e73
The patch set for Buffalo WLAE-AG300N initial support.
There is another patch for wireless led support that
is posted separately.
Note on serial console:
This unit has buffalo standard 4 pin console, but the unit may not power
on if some console apparatus is connected. This is probably due to some
electronic interaction between the unit's electronic power switch circuit
and the serial console apparatus. If this happens, it is required to power
on the unit without the console, then quickly (re-)attach it.
[juhosg: fix coding style]
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32931 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch helps properly detect a WNDRMAC device. Before this
patch the model is detected as "NETGEAR ?????????N".
Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32453 3c298f89-4303-0410-b956-a3cf2f4a3e73
Support for TP-Link TL-MR3040. Power LED not working - always on red, after
start should be green.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31845 3c298f89-4303-0410-b956-a3cf2f4a3e73
On TP-Link TL-WR741ND version 4, the WLAN LED must be configured to work.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31461 3c298f89-4303-0410-b956-a3cf2f4a3e73
Great collaboration on these two fantastic routers on the openwrt forum:
https://forum.openwrt.org/viewtopic.php?id=32320
Above all kudos to aryufan. Well done and thank you everyone else who
contributed.
To-Do: LED for wlan is not yet activated
To-Do: TxPower over 20dBm (RB751U) or 22dBm (RB751G) are not accepted by
the router
Signed-off-by: Hanno Schupp <hanno.schupp@gmail.com>
[juhosg: fix line wrapped patch, fix checkpatch errors, add missing
kernel patches]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31208 3c298f89-4303-0410-b956-a3cf2f4a3e73
Support status led in diag.sh for RB750
Patch from: Evangelos Arkalis <arkalis.e@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31207 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for D-LINK DIR-615 E4 board. It's mostly based
on the existing support for DIR-600 A1, with some changes in the leds
configuration.
It's an updated version of the patch that reliably works on my hw for
about a year (it was built from trunk on Jan 2011). When I decided to
update the firmware and checked for the current support for that device,
I also found previously posted patches by Alexey Loukianov that
mentioned some stability issues. I'm not sure where could be the
difference, the patches are very similar except the wmac led pin number
- I was using 1, and those patches used 17.
[juhosg: add 3.2 support]
Signed-off-by: Vadim Girlin <vadimgirlin@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29973 3c298f89-4303-0410-b956-a3cf2f4a3e73
Adds support for TL-MR11U, a portable router with very similar
hardware to the TL-WR703N and TL-MR3020, but with an onboard
2000mAh battery.
Tested, working:
All interfaces (Ethernet, 802.11n, USB)
WPS & Reset switches (Power appears to be a hardware slider)
Ethernet, Wifi, 3G LEDs (Power & charging LEDs hardware controlled)
Sysupgrade
[juhosg: fix indentations to use TABs instead of spaces, fix 3.2 patch
breakage]
Signed-off-by: Simon Taylor <simon.taylor.uk@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29972 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for Compex WPE72 bare board and Compex WPE72NX
Indoor Access Point.
[juhosg: add support to 3.2 as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29912 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch fixes the board detection of the TL-MR3020.
The LED behaviour has also been modified:
* The WPS LED is the diag LED now.
* A netdev trigger for the LAN LED has been added.
The profile of the TL-MR3020 has been updated because the needed package
"kmod-ledtrig-usbdev" was missing which resulted in a non-working usbdev
trigger for the 3G/USB LED.
[juhosg: the board name changes has been removed, and the kernel files
has been changed instead.]
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29905 3c298f89-4303-0410-b956-a3cf2f4a3e73
Luka Perkov
Gabor Juhos
Jo-Philipp Wich
Mirko Vogt
Daniel Dickinson
Felix Fietkau
Florian Fainelli