Build all geode platform drivers into the kernel
Remove kmod-* packages for these drivers
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44809 3c298f89-4303-0410-b956-a3cf2f4a3e73
Eliminates excessive skb copying when bridging from LAN to WLAN on
ramips.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44797 3c298f89-4303-0410-b956-a3cf2f4a3e73
While the switch positions aren't explicitly labeled as on and off, we've heard
complaints about them being wrong. This patch changes the handling to match the
stock firmware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44795 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch allows AP148 to boot from NOR flash.
As we're using a FIT image as kernel (which includes kernel bin + DTB)
we enable the MTD_SPLIT_FIT_FW kernel option, which will detect the FIT
image and automatically split the "firmware" partition into 2 MTD parts
(kernel + rootfs).
The rootfs will then be parsed and split between rootfs + rootfs_data,
as usual.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44794 3c298f89-4303-0410-b956-a3cf2f4a3e73
Only one bootargs is really needed: the tty port. All the other
information will use the OpenWrt mechanisms.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44793 3c298f89-4303-0410-b956-a3cf2f4a3e73
If this option is enabled, the FIT image format will be detected and
split by the mtdsplit code. Detection is based upon the FDT magic, which
will trigger the parsing and detection of the rootfs, ending-up in the
creation of the 2 new partitions.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44792 3c298f89-4303-0410-b956-a3cf2f4a3e73
My previous patch regarding the Hornet-UB board
(commit: beed4d82d6a0154b0cd5f7b84e2180215ace6718) actually
causes the WPS led state to be inverted. Practically this meant
that value 0 in /sys/class/led/alfa:blue:wps/brightness would
turn the LED on and any positive value (1-255) would turn it off.
The above of course is confusing and hence reverting this value
back to the way it was before beed4d82d6a0154b0cd5f7b84e2180215ace6718.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44791 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will now actually enable the mib counters instead of enabling rx/tx for
the first switch port.
Reported-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44788 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix the module path for linux 3.18+.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44785 3c298f89-4303-0410-b956-a3cf2f4a3e73
copied target/linux/x86/config-3.14 and target/linux/x86/patches-3.14 to
3.18 equivalents and then tweaked until it built.
Tested on alix2, soekris net4826 and soekris net4521.
Still having trouble with net4826 booting from Grub, alix2 and net4521
are fine.
Signed-off-by: Russell Senior <russell@personaltelco.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44758 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move first 3 patches to 0xx numbers range to denote that this is
backported code and they should be removed when we update
kernel to version >= 3.19
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44732 3c298f89-4303-0410-b956-a3cf2f4a3e73
To finally sync code with upsream cleanup registers headers, and update
several comments and kernel config symbols descriptions. No functional
changes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44731 3c298f89-4303-0410-b956-a3cf2f4a3e73
Cleanup board patch by moving code to specific patches, and factor out
leds to separate patch. No functional changes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44729 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move GPIO patches behind PCI patch, since they are not yet merged
upstream.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44728 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rework MISC and PCI IRQ controllers code to use IRQ domains and bitops.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44727 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make register names more consistent, mostly add appropriate prefix
(AR5312_ or AR2315_) or _BASE suffix. Also add macro to simplify mask
and shift operation.
No functional changes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44726 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are no external users (last one was PCI driver) for these headers,
so move them to arch directory. Few macroses from ar231x.h header moved
to devices.h and file was removed.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44724 3c298f89-4303-0410-b956-a3cf2f4a3e73
Honestly remap main SoC MMR mem and use accessor functions to
interact with registers. Now registers defined relatively to base
address (e.g. SDRAM controller base address).
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44723 3c298f89-4303-0410-b956-a3cf2f4a3e73
AFAIK, no one AR2315+ chip (AR2315, AR2316, AR2317, AR2318) does not
contain IR block, so remove IR registers definitions. Also remove few
unused macroses.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44722 3c298f89-4303-0410-b956-a3cf2f4a3e73
Pass PCI IRQ and I/O memory ranges via platform device resources, this
change makes PCI controller driver independed from arch headers, so
also remove few includes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44721 3c298f89-4303-0410-b956-a3cf2f4a3e73
Honestly remap PCI controller MMR and use accessor functions to interact
with registers.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44720 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add container and place all context specific variables and structure to
it.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44719 3c298f89-4303-0410-b956-a3cf2f4a3e73
Put AR2315_PCI_HOST_SDRAM_BASEADDR macro to DMA header, since this is
arbitrary value and not some hw specific constant. Also this relocation
decouples dma from HW specific header.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44716 3c298f89-4303-0410-b956-a3cf2f4a3e73
Do not use prom_init() callback, do memory initialization in
plat_mem_setup() callback and move serial port configuration to
arch_initcall stage.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44715 3c298f89-4303-0410-b956-a3cf2f4a3e73
No functional changes, just change functions order in source file.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44714 3c298f89-4303-0410-b956-a3cf2f4a3e73
Check SoC family (AR5312+ or AR2315+) before call instead of checking it
inside the called function. Also convert ar{5312,2315}_init_device()
function to void, since they both return zero and nobody care about
return value.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44713 3c298f89-4303-0410-b956-a3cf2f4a3e73
Sync functions, variables and enums names with upstream. Mostly replace
'ar231x_' prefix by 'ath25_'.
No functional changes, except few 'int' -> 'unsigned' changes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44712 3c298f89-4303-0410-b956-a3cf2f4a3e73
Ethernet controller driver don't use boarddata directly, so remove
corresponding field from its platform device structure.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44710 3c298f89-4303-0410-b956-a3cf2f4a3e73
This header provides prototype for function without realization and
users.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44709 3c298f89-4303-0410-b956-a3cf2f4a3e73
This problem has existed at least since Attitude Adjustment and
is also present in trunk. Basically on the Hornet-UB board the
functionality of RESET and WPS have "switched places".
There are two tickets about the issue at dev.openwrt.org,
The solution suggested on them both is incomplete though
and introduces the following proglem:
Patching as suggested on #14136/#15282 will result in a situation
where simply pressing the RESET button on the bottom will cause
FACTORY RESET to be run. This is due to GPIO high/low state being
incorrect as a result of the above change and virtually the RESET
button is in the pressed-down state the entire time. When it is
then physically pressed, that causes the opposite, release, to be
triggered and since to the board it seemed that the button was
pressed long before it was released, the FACTORY RESET results.
The attached patch works as expected. I have verified both the
incorrect functionality as well as after fixing the issue as
described in the patch and flashing the resulting firmware to a
Hornet-UB board.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44692 3c298f89-4303-0410-b956-a3cf2f4a3e73
ralink i2c driver is not working on MT7621 platform. Porting a new drivers from MTK's source code.
Signed-off-by: daixj <fl.service@t-firefly.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44690 3c298f89-4303-0410-b956-a3cf2f4a3e73
Looks like the BCM53012 has a similar problem to the BCM53011.
Signed-off-by: Ian Kent <raven@themaw.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44680 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix thinko' in the bcm47xx sprom driver.
Signed-off-by: Ian Kent <raven@themaw.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44679 3c298f89-4303-0410-b956-a3cf2f4a3e73
danube needs to be added
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44677 3c298f89-4303-0410-b956-a3cf2f4a3e73
Here the device tree entry for ifxhcd is listed as compatible with one
supported in dwc2 (after patching the dwc driver appropriately).
A second entry is added to support the second core of the hcd. This
entry is listed to be compatible with only dwc2. Done this way there
should be backwards support for both hcd drivers (ltq-hcd and dwc2)
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44676 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.
This patch is necessary to access dwc2 registers correctly on big
endian systems such as the mips based SoCs made by Lantiq. Then dwc2
can be used to replace ifx-hcd driver for Lantiq platforms found e.g.
in OpenWrt.
The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44675 3c298f89-4303-0410-b956-a3cf2f4a3e73
Lantiq driver does not work with autodetected fifo sizes so use ones
from original ltq-hcd driver in dwc2. Other values can be
autodetected.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44674 3c298f89-4303-0410-b956-a3cf2f4a3e73
Port gpio code from original ltq-hcd driver to dwc2.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44673 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add VR9 specific usb initialization bits from ltq-hcd to platform
initialization.
This patch is more of a proof-of-concept than production quality
since the initialization registers are different on other lantiq
platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44672 3c298f89-4303-0410-b956-a3cf2f4a3e73
Previously, the generated images for the My Net Wi-fi Range Extender
wouldn't always work (and panic) due to the fixed mtd offsets and
sizes for the kernel and rootfs. This patch fixes the problem by
utilizing the shared Cybertan's partition parser to recalculate
the mtd partitions for every image dynamically everytime.
Reported-by: Pascal Paradis <peparadis@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44665 3c298f89-4303-0410-b956-a3cf2f4a3e73
By removing the NL16 signature check, the parser can be
utilized by other devices like the WD My Net Wi-fi Range
Extender.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44664 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch renames the partition parser from
wrt160nl to more generic cybertan.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44663 3c298f89-4303-0410-b956-a3cf2f4a3e73
405-mtd-tp-link-partition-parser.patch was updating the
WRT160NL's partition parser Kconfig. This patch moves the
relevant change into the right file:
404-mtd-wrt160nl-trx-parser.patch
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44662 3c298f89-4303-0410-b956-a3cf2f4a3e73
ath10k is loaded before ath9k, so the 5GHz adapter becomes phy0.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44659 3c298f89-4303-0410-b956-a3cf2f4a3e73
This commit re-adds a patch from 3.14 that is required for UBI block
devices with an EOF marker to be successfully mounted.
Signed-off-by: Oliver Smith <oliver@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44658 3c298f89-4303-0410-b956-a3cf2f4a3e73
gpio api has changed. the remove call no longer returns a value.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44650 3c298f89-4303-0410-b956-a3cf2f4a3e73
Please also backport to Barrier Breaker (this same patch applies there too).
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44647 3c298f89-4303-0410-b956-a3cf2f4a3e73
OpenWrt can be flashed with following uboot commands:
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj558-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44620 3c298f89-4303-0410-b956-a3cf2f4a3e73
This will allow ipq806x to support multiple kernel version more easily.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44616 3c298f89-4303-0410-b956-a3cf2f4a3e73
KERNFS symbol is selected by SYSFS, so place it in generic config.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44615 3c298f89-4303-0410-b956-a3cf2f4a3e73
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44614 3c298f89-4303-0410-b956-a3cf2f4a3e73
HAMRADIO enabled in all generic configs, but no one platform directly
use related drivers/protocols. This symbol is only used for kmod-ax25
package modules. Furthermore, half of platforms explicitly disables
this symbol, what silently disables build of modules for kmod-ax25
package.
So disable HAMRADIO by-default in generic config, add it to kmod-ax25
package and remove it from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44613 3c298f89-4303-0410-b956-a3cf2f4a3e73
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44612 3c298f89-4303-0410-b956-a3cf2f4a3e73
CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled
in generic config, so we don't need this symbol in platform specific
configurations.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44611 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now bcma provides IRQ domain we don't have to poll anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44596 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes several issues in the network stack.
Full changelog:
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.8
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44593 3c298f89-4303-0410-b956-a3cf2f4a3e73
Tested by Jonas on WP54g, thank you!
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44588 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most devices have only 16 MiB of RAM, this will allow them to boot
without OOM.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44587 3c298f89-4303-0410-b956-a3cf2f4a3e73
The driver code for supporting these subtargets was already removed a while ago,
so
the current images wont actually boot.
It is also quite unlikely that there are any users of them at this point, so
remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44586 3c298f89-4303-0410-b956-a3cf2f4a3e73
The flag is experimental and requires toolchain support, which we don't
provide. Also neither target has an FPU so it becomes meaningless
without the FPU emulator enabled.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44584 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44583 3c298f89-4303-0410-b956-a3cf2f4a3e73
Saves us pulling in the input system, shaving off a few kb from image
sizes.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44582 3c298f89-4303-0410-b956-a3cf2f4a3e73
Linux commit d75b1ade567ffab ("net: less interrupt masking in NAPI")
chose the samantics of the napi poll return value, which caused napi to
not resume interrups/polling anymore.
Fix the return value to restore expected behaviour.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44576 3c298f89-4303-0410-b956-a3cf2f4a3e73
Legacy probe passed the IRQSTAT registers instead of the IRQMASK
registers causing all register accesses to be offset by 16 bytes.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44575 3c298f89-4303-0410-b956-a3cf2f4a3e73
The driver expected data then dir, but both dts and legacy code passed
dir then data. Fix this by making the driver expect the registers in
ascending order, i.e. dir then data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44574 3c298f89-4303-0410-b956-a3cf2f4a3e73
For bcm63xx integrated switches, broadcom changed the data endianess
to match the system endianess. But this only applies to within one word,
which causes 48/64 bit values to be still split into their "litte endian"
groups.
E.g. 48 bit values (with 5 being the most significant byte) aligned
0x00 ..01 or 0123
0x04 2345 45..
will become
0x00 ..10 resp. 3210
0x04 5432 54..
Likewise for 64 bit values.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44568 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now that all gpio users without named gpios use DT, we do not need
to fix the gpio controller bases anymore.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44567 3c298f89-4303-0410-b956-a3cf2f4a3e73
Register buttons and leds through DT for all available dts,
and remove them from the board files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: remove leds/buttons from board files
fix wrong led polarities for dsl-274xb-c2, cpva642, p870hw
comment out spi-gpio and associated leds]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44566 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a generic mmio gpio controller based driver and probe it
through device tree.
Use aliases for base calculation until we converted all users to
device tree or named gpios.
Convert bcm63xx_enet's ephy-reset gpio to use a named gpio.
While at it, remove the duplicate reset gpio defintion for livebox.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44565 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a dtsi for bcm3368, add a dts and profile for cvg834g, and convert
it to use ImageDTB. Since HCS requires more arguments, enhance the max
arguments of the call.
The image name is intentionally left blank to prevent non-initramfs
images to be built, as they currently contain no rootfs and consequently
won't work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44561 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most 16 MiB RAM devices don't even load elf kernels, so it's safe to
assume we have at least 32 MB RAM. This fixes tftp booting with the
default package set as this already produces an uncompressed
kernel > 8 MiB.
New limit is 8 MiB compressed / 24 MiB compressed.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44558 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the need for the header file to be exported - we don't need most
of it anyway; all we care about are the offset of the rootfs length and
header crc fields.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44557 3c298f89-4303-0410-b956-a3cf2f4a3e73
We do not need to align the start of read only rootfs's to erase blocks.
This allows us to write the squashfs rootfs directly behind the kernel,
potentially freeing up one erase block.
We still need to align for jffs2, so add a flag for imagetag to
optionally align the rootfs start.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44556 3c298f89-4303-0410-b956-a3cf2f4a3e73
We do not use the result, so no need to call it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44555 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for TP-Link TL-WA7210n[0]
[0] http://www.tplink.com/en/products/details/?model=TL-WA7210N
Signed-off-by: Hendrik Frenzel <hfrenzel@scunc.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44526 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds the GMAC entries in the ipq806x dtsi file as well as in the
ap148 specific dts file.
This also adds the MDIO change as well.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44520 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change is fixing the issues observed when booting from NOR flash
with SMP enabled.
Error logs below:
building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of
xref (0 dead, 0 orphan) found.
m25p80 spi32766.0: SPI transfer failed: -110
spi_master spi32766: failed to transfer one message from queue
jffs2: Write of 873 bytes at 0x019001e8 failed. returned 0, retlen 792
Patch is cherry-picked from here:
https://www.codeaurora.org/cgit/quic/qsdk/oss/kernel/linux-msm/commit/drivers/spi/spi-qup.c?h=coconut_20140924&id=4faba89e3ffbb1c5f6232651375b9b3212b50f02
More details in the patch file.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44518 3c298f89-4303-0410-b956-a3cf2f4a3e73
It took very little to make the TL-WDR4900 work under 3.19:
- config is the same as for 3.18
- only patch 210 had to be refreshed, the other patches are
the same as for 3.18
- in /etc/config/wireless the path options need to be prefixed
with "platform/" ('platform/ffe09000.pci/...')
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44517 3c298f89-4303-0410-b956-a3cf2f4a3e73
This sets 'enable_vlan' and thus uses 802.1q
VLANs, but without tagging on either interface.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44509 3c298f89-4303-0410-b956-a3cf2f4a3e73
Toggles the LA bit on the WAN interface.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44508 3c298f89-4303-0410-b956-a3cf2f4a3e73
ipq806x target has been upgraded to 3.14. There is no need to maintain
this file anymore.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44505 3c298f89-4303-0410-b956-a3cf2f4a3e73
The watchdog driver already registers a restart notifier, we just have
to enable it in the config and in the DT to fix the "reboot" command.
This is done by integratin the following patch-set:
https://lkml.org/lkml/2015/2/20/610
I'm copy-pasting the description below:
qcom-wdt is currently assuming the presence of a dedicated node in DT
to gets its configuration. However, on msm architecture, the watchdog is
usually part of the timer block. So this patch-set is changing the driver
and slightly enhancing the timer DT bindings to provide the relevant clocks
and interrupts.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44504 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some bootloaders seem to trigger the watchdog during the boot process,
therefore the lack of watchdog driver trigger a reboot a few seconds
after boot. So we'll enable it here to avoid it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44503 3c298f89-4303-0410-b956-a3cf2f4a3e73
MPIC timers are enabled in the config, however a devicetree clock setting
is missing causing the following error:
/soc@ffe00000/timer@41100: cannot get timer frequency.
/soc@ffe00000/timer@42100: cannot get timer frequency.
This patch adds the missing clock and avoids the error.
It's a functional copy of this code
do_fixup_by_compat_u32(blob, "fsl,mpic",
"clock-frequency", get_bus_freq(0), 1);
in arch/powerpc/cpu/mpc85xx/fdt.c in the u-boot code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44501 3c298f89-4303-0410-b956-a3cf2f4a3e73
Defaulting to disabled, based on the value of
the (old?) CONFIG_RALINK_USBPHY
Signed-off-by: Claudio Leite <leitec@staticky.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44500 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thanks to Bruno Randolf for testing and Manuel Lauss for providing a fix.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44487 3c298f89-4303-0410-b956-a3cf2f4a3e73
The firware md5sum check never worked due to missing dollar signs.
Also suppress
`md5sum: can't open '/lib/firmware/ath10k/QCA988X/hw2.0/firmware-3.bin'`
error on any board not using ath10k.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44486 3c298f89-4303-0410-b956-a3cf2f4a3e73
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44470 3c298f89-4303-0410-b956-a3cf2f4a3e73
To choose whether bulid or not RT288x PCIe bus driver, CONFIG_SOC_RT2880 is wrong.
Here is its fix, and enables PCIe bus driver for some targets which have 2nd WiFi chipset via PCIe bus.
signed-off-by: ngc@ff.iij4u.or.jp
————
————
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44469 3c298f89-4303-0410-b956-a3cf2f4a3e73
- according to imx6 Makefile and u-Boot documentation is itb
and probably should not be changed
- this fixes build error if CONFIG_TARGET_ROOTFS_INCLUDE_FIT is set
(missing .itb file)
- use DTS_DIR (like in imx6 Makefile)
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44468 3c298f89-4303-0410-b956-a3cf2f4a3e73
The current pxa3xx_nand driver doesn't support sub-page writing,
so the VID header offset must be specified explicitly.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44455 3c298f89-4303-0410-b956-a3cf2f4a3e73
oops, accidently moved instead of copied them
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44454 3c298f89-4303-0410-b956-a3cf2f4a3e73
ZyXEL NBG6716 "rfkill" is a switch, not a button.
Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44453 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some Lantiq SoCs are not able to use buffered writes properly with
Intel command set flash due to the way NOR addresses on EBU are
manipulated. This patch disables buffered writes on those devices.
The only device affected at the moment is ARV4510PW, others use
AMD/Fujitsu command set.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44451 3c298f89-4303-0410-b956-a3cf2f4a3e73
For targets with NO_XIP ltq_mtd->map[i].phys equals -1 and devm_ioremap fails.
Fix this by using pdev->resource[i].start instead.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44450 3c298f89-4303-0410-b956-a3cf2f4a3e73
procd gets last console from cmdline, so swapping tty1 (framebuffer) and ttyAMA0 (uart) is enough to force procd output via uart
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44448 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thank you Dimitri for testing this.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44430 3c298f89-4303-0410-b956-a3cf2f4a3e73
- Allow --command-line parameters of kexec-tools be parsed and used by
the kernel.
- For malta machine, mark kernel code and kernel data segments as
"System RAM" instead of "reserved" in /proc/iomem, otherwise
kexec-tools will complain that program segments in ELF kernel file
are invalid.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44429 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds corrected profile and build image for the TL-MR12U board.
Unfortunately i cannot test the factory image since i can't find anywhere
the original chinese firmware but
the generated openwrt-ar71xx-generic-tl-mr12u-v1-squashfs-sysupgrade.bin
worked just fine over a modified mr3040 factory image i managed to modify
to initially flash the mr12u from the original firmware.
Proper kernel support probably should be added since cat /proc/cpuinfo shows
MR13U.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44427 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds user-space support for the TL-MR12U board based on the mr13u patches.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44426 3c298f89-4303-0410-b956-a3cf2f4a3e73
ZyXEL NBG6716 add missing GPIO USB power on/off
Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44425 3c298f89-4303-0410-b956-a3cf2f4a3e73
We obviously can't use sizeof(*buf) which is always 1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44424 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add GoFlex Net "Board Name" , set and cleanup network default and LEDs.
Remove kmod-rtc-marvell from default packages, as the GoFlex net does not have a RTC.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44422 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Felix Fietkau
Jonas Gorski
Rafał Miłecki
Imre Kaloz
Luka Perkov
Lars-Peter Clausen
Jo-Philipp Wich
Nicolas Thill