Note that the Alix6 uses GPIO 27 to disable wireless transmit (W_DIS#), whereas on all other versions this is used to actuate the speaker.
GPIO 1 : SIM select (Alix6)
GPIO 6 : LED1
GPIO 25 : LED2
GPIO 27 : LED3 or RFKILL (Alix6)
GPIO 24 : Soft switch 1
No kernel version bump. Added i2c-scx200-acb for lm-sensors support.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26879 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add the required board definition, default config and image generation for
the T-Home Speedport W 303V Typ B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26878 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add two helpers for generating correctly tagged images for the T-Home
Speedport W 303V Typ B as well as xor'd ones as required by CFE.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26877 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rename the DSL-274xB rev C2's board ID to "AW4139" to match the one used
for the rev C3 (same hardware) and add a fixup for C2. Also generate
images for C3.
While we are at it, rename the LEDs to conform to the Linux LED naming
conventions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26876 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make the fixup board ID independent from the image name to allow using
the same board ID for similar devices.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26874 3c298f89-4303-0410-b956-a3cf2f4a3e73
package/kernel/modules/other.mk is getting big enough that putting the LEDs stuff into its own file makes sense.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26868 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds 802.1Q VLAN support for the ADM6996M chip.
The driver is loaded for both the FC and M model. It will detect which of the
two chips is connected. The FC model is initialised, but no further
functionality is offered.
The PHY driver will always report "100 Mbit/s, link up", for both the M and FC
models. This reflects the fact that the link between switch chip and Ethernet
MAC is always on[1].
Further documentation can be found in the kernel's
Documentation/networking/adm6996.txt
Signed-of-By: Peter Lebbing <peter@digitalbrains.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26865 3c298f89-4303-0410-b956-a3cf2f4a3e73
2000::/3 space, so a default route of ::/0 is more correct.
Thanks Dave Taht
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26857 3c298f89-4303-0410-b956-a3cf2f4a3e73
The function __devinit ag71xx_probe() references
a function __devexit ag71xx_phy_disconnect().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
ag71xx_phy_disconnect() so it may be used outside an exit section.
The function ag71xx_phy_disconnect() references a function in an exit
section.
Often the function ag71xx_ar7240_cleanup() has valid usage outside the
exit section
and the fix is to remove the __devexit annotation of
ag71xx_ar7240_cleanup.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26855 3c298f89-4303-0410-b956-a3cf2f4a3e73
kmod-crypto-ipsec bundles some otherwise unprovided kernel crypto
modules that are useful for IPSEC. This is an alternative to breaking
these modules out into kmod-crypto-wq (crypto_wq.ko), kmod-crypto-rng
(rng.ko and krng.ko), and kmod-crypto-iv (eseqiv.ko and chainiv.ko).
Signed-off-by: Lars Hjersted <lars@hjersted.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26814 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add kmod-crypto-iv as a dependency for kmod-ipsec. Also remove the
extraneous kmod-crypto-core dependency to eliminate recursion.
Signed-off-by: Lars Hjersted <lars@hjersted.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26813 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds kmod-crypto-wq, kmod-crypto-rng, and kmod-crypto-iv
packages. These packages provide some missing kernel crypto modules
which are required for IPSEC. The strongswan4, ipsec-tools, and possibly
other IPSEC packages do not work properly without these modules.
NOTE: The KCONFIG associated with each of these modules gets selected
whenever CRYPTO_MANAGER (kmod-crypto-manager) is selected so these
modules are already being built.
Signed-off-by: Lars Hjersted <lars@hjersted.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26812 3c298f89-4303-0410-b956-a3cf2f4a3e73
The via-sata and gpio-nsc modules are both unneeded on the Geos platform.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26811 3c298f89-4303-0410-b956-a3cf2f4a3e73
Two examples of potentially useful configurations (commented out, of course):
(a) map the ssh service running on the firewall to 22001 externally, without modifying the configuration of the daemon itself. this allows port 22 on the WAN side to then be port-forwarded to a
LAN-based machine if desired, or if not, simply obscures the port from external attack.
(b) allow IPsec/ESP and ISAKMP (UDP-based key exchange) to happen by default. useful for most modern VPN clients you might have on your WAN.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26805 3c298f89-4303-0410-b956-a3cf2f4a3e73
Daniel Dickinson
Florian Fainelli
John Crispin
Gabor Juhos
Travis Kemen
Jo-Philipp Wich
Hauke Mehrtens
Alexandros C. Couloumbis
Felix Fietkau