The switch is renamed to "switch0" in newer (3.10) linux kernels.
Configure the switch using vlans by default and only configure
the physical switch ports that are present.
Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38673 3c298f89-4303-0410-b956-a3cf2f4a3e73
init no longer exists as a parameter
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38342 3c298f89-4303-0410-b956-a3cf2f4a3e73
*) can not connect to switch chip
*) only one usb port is working
*) wifi is not working
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37712 3c298f89-4303-0410-b956-a3cf2f4a3e73
based on work from Matti Laasko that he posted in the wiki
Signed-off-by: John Crispin <blogic@openwrt.or
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37704 3c298f89-4303-0410-b956-a3cf2f4a3e73
This provides a boot LED sequence suitable for devices with both red and
green LEDs for power. This assumes no "default-on" settings in the
device tree.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36899 3c298f89-4303-0410-b956-a3cf2f4a3e73
On linux 3.8 the switch is named as "switch0", but the network configuration script names it as "eth0", causing no communication over ethernet due to no proper VLAN config.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36782 3c298f89-4303-0410-b956-a3cf2f4a3e73
This requires all the preceding patches and finishes support for the
DGN3500, also removing an obsolete file.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36781 3c298f89-4303-0410-b956-a3cf2f4a3e73
This reassigns the PPPoE status to the LED that was intended to indicate
it, rather than the DSL sync light.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36777 3c298f89-4303-0410-b956-a3cf2f4a3e73
user-space support for extracting the EEPROM for the RaLink WiFi is still
missing. Besides this, it's all working.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35990 3c298f89-4303-0410-b956-a3cf2f4a3e73
WIFI eeprom:
As discussed, it is impossible for nand and spi flash platforms to have the eeprom data available from mtd. I suggested to load the eeprom from user-space. I've looked into regular firmware loading but this is only possible when using modules. I've created a sysfs entry that allows reading and writing the eeprom data to the platform data. After loading the eeprom data I rely on pci-hotplug support to disable the bogus pci device and rescan the bus (with fixups and all). Because hotplug is not available, an init script is created that performs the copy from mtd to platform data. I think it is best to eventually move the sysfs functions to dev_wifi_athxk.c file, this would get rid of the external to the ath9k platform data.
SPI flash:
It seems that the spi-xway driver is not really working. It causes my kernel to crash in all sorts of ways. I added to bitbang SPI to be able to the calibration data mention above.
I've kept the original mtd partitioning that Netgear uses.
Buttons/LED:
Both buttons are working properly. Two leds are not enabled: The red internet led is connected to the pci_gnt1 pin... I can't disable it because then DMA stops working.
The green wifi led is connected to an unknown atheros gpio.
Signed-off-by: Pieter Voorthuijsen <p.voorthuijsen at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31910 3c298f89-4303-0410-b956-a3cf2f4a3e73
The VLAN mapping on the ARV4520PW board is the following:
port on Router: | VLAN in software:
LAN 1 | 3
LAN 2 | 2
LAN 3 | 1
LAN 4 | 0
DSL | 4
So LAN4 is not VLAN4 but VLAN0 (VLAN4 is DSL port) -> set "3 2 1 0 5t" as default switch config.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31391 3c298f89-4303-0410-b956-a3cf2f4a3e73
With this patch it is possible to generate uboot environment config file
inside lantiq target. Currently it is only supporting GIGASX76X board.
uboot environment config is used by fw_printenv fw_setenv tools.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30537 3c298f89-4303-0410-b956-a3cf2f4a3e73
* fixes leds
* adds all leds found on the sx763 board
* removes board_config from flash layout because wireless data is stored in kernel (ath5k)
* fix button handling
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29763 3c298f89-4303-0410-b956-a3cf2f4a3e73
* backport 2.6.8 patches to .39 / .32.33
* remove lqtapi
* bump tapi/dsl to .39
* migrate to new ltq_ style api
* add amazon_se support
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27026 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Luka Perkov
Felix Fietkau
Steven Barth
Jo-Philipp Wich
Mirko Vogt
Gabor Juhos