Only support Linux at the moment.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42988 3c298f89-4303-0410-b956-a3cf2f4a3e73
[base-files] failsafe-mode: print short help on commandline
Like mentioned in ticket https://dev.openwrt.org/ticket/11911
this should make the IRC much quieter. Failsafe is somehow
special and even experienced users are helpless, because they
are not used to this seldom situation. Also: likely you have
no internet access in this mode, so you cannot use the wiki.
a failsafe-session now looks like this:
first we see from 'package/base-files/files/bin/login.sh' the hint:
=== IMPORTANT ============================
Use 'passwd' to set your login password
this will disable telnet and enable SSH
------------------------------------------
after this the /etc/banner ("OpenWrt - wireless freedom")
and then the new text:
================= FAILSAFE MODE active ================
special commands:
* firstboot reset settings to factory defaults
* mount_root mount root-partition with config files
after mount_root:
* passwd change root's password
* /etc/config directory with config files
for more help see:
http://wiki.openwrt.org/doc/howto/generic.failsafe
=======================================================
this supersedes the old patches:
http://patchwork.openwrt.org/patch/3337/http://patchwork.openwrt.org/patch/3553/
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42985 3c298f89-4303-0410-b956-a3cf2f4a3e73
SENSORS_VEXPRESS is masked by HWMON
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42984 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix sysupgrade to determine the correct boot block device to use if
/proc/cmdline contains a PARTUUID root.
Change the preinit move_config() hook to use the UUID scanning code
from sysupgrade in order to avoid code duplication.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42968 3c298f89-4303-0410-b956-a3cf2f4a3e73
Enable the required squashfs and block2mtd support in the kernel in order
to be able to actually boot them.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42967 3c298f89-4303-0410-b956-a3cf2f4a3e73
If the underlying block device is a USB device it might require some
time to settle, observed when booting a squashfs image from sd card
on an Alix APU board.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42966 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Makefile for binutils creates a broken symlink to "binutils-linaro" in
"trunk/build_dir/toolchain-<target>_gcc-4.9-linaro_uClibc-0.9.33.2".
Modify the Makefile to point the symlink to the correct directory.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42954 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix the move_config() procedure to properly find the corresponding disk if
the rootfs was mounted by PARTUUID instead of a device node.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42946 3c298f89-4303-0410-b956-a3cf2f4a3e73
This kmod is required by the Alix APU 1D4 to be reachable after
installing an x86-64 image.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42945 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Rewrite ndp proxy using kernel proxying
* Aid flash-renumbering in hybrid DHCPv6-mode
* Unicast RAs to RS senders
* Add support for router address
Signed-off-by: Steven Barth <steven@midlink.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42944 3c298f89-4303-0410-b956-a3cf2f4a3e73
We still don't have a smart sysupgrade method, but at least we can use
UBI which provides some protection for rootfs (SquashFS).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42941 3c298f89-4303-0410-b956-a3cf2f4a3e73
UBI requires PEBs to be formatted (with a valid UBI header) or empty
(0xFF), however CFE doesn't clear blocks after flashing the image. To
workaround this problem, teach UBI to recognize EOF mark in a similar
way JFFS2 handles that in OpenWrt.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42940 3c298f89-4303-0410-b956-a3cf2f4a3e73
This could be used on NAND devices once we get UBI working.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42938 3c298f89-4303-0410-b956-a3cf2f4a3e73
This will allow us to add proper support for NAND one day.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42937 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change configures grub to mount the rootfs by PARTUUID instead of the
device path if CONFIG_TARGET_ROOTFS_PARTNAME is unset.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42936 3c298f89-4303-0410-b956-a3cf2f4a3e73
- Add current buildroot scm url as base feed to feeds.conf
- Prefer feeds.conf over feeds.conf.default when generating the SDK feeds.conf.default
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42935 3c298f89-4303-0410-b956-a3cf2f4a3e73
- Consider not installed feeds as well
- Add option to decide whether to comment disabled feeds
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42931 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Felix Fietkau
Jo-Philipp Wich
Steven Barth
Rafał Miłecki