This patch sets the cflags -mtune=34kc -mdsp only in XWAY subtarget, while the others remain with mtune=mips32r2.
Although the Danube has a Mips 24KEc core performs well with the above cflags.
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37006 3c298f89-4303-0410-b956-a3cf2f4a3e73
Set mips16 support in XWAY subtarget.
This patch is based in changeset #36600
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37005 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix EBU leds by removing req2 and gnt2 from pinmux.
Fix rfkill button gpio.
Enable reset button.
Fix power led activation status.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37004 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use platform data array for storing ath5k EEPROM instead of creating another one.
EEPROM size is 2048 words (2 bytes), so we must read 4096 bytes from flash.
No need to keep the checksum fix now that the EEPROM is loaded completely.
Add a manual eeprom swap for ath9k and keep the endian way.
Use mac-offset property retrieved from the DTS.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36901 3c298f89-4303-0410-b956-a3cf2f4a3e73
Seems the existing kernel config for 3.8 was cp'ed from 3.7; this patch
is the result of "make kernel_oldconfig" with defaults for new options.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36900 3c298f89-4303-0410-b956-a3cf2f4a3e73
This provides a boot LED sequence suitable for devices with both red and
green LEDs for power. This assumes no "default-on" settings in the
device tree.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36899 3c298f89-4303-0410-b956-a3cf2f4a3e73
submitter was informed of a endinaess swap regression and replied with "works on my board"
revert the patch and make arv7518 wifi work again
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36807 3c298f89-4303-0410-b956-a3cf2f4a3e73
The GPIO buttons of ARV752DPW are active low.
Treating them as active high caused a reboot loop as a reset-button
press is detected by gpio-button-hotplug/gpio-keys-polled on startup.
This fixes: https://dev.openwrt.org/ticket/12642
Signed-off-by: Rafael Gieschke <rafael@gieschke.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36783 3c298f89-4303-0410-b956-a3cf2f4a3e73
On linux 3.8 the switch is named as "switch0", but the network configuration script names it as "eth0", causing no communication over ethernet due to no proper VLAN config.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36782 3c298f89-4303-0410-b956-a3cf2f4a3e73
This requires all the preceding patches and finishes support for the
DGN3500, also removing an obsolete file.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36781 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch enables retrieving the wifi calibration data from an MTD
partition. It requires the previous patch.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36779 3c298f89-4303-0410-b956-a3cf2f4a3e73
This postpones the initialization of PCI and wifi until after the MTD
initialization, so that calibration data may be loaded from there.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36778 3c298f89-4303-0410-b956-a3cf2f4a3e73
This reassigns the PPPoE status to the LED that was intended to indicate
it, rather than the DSL sync light.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36777 3c298f89-4303-0410-b956-a3cf2f4a3e73
this adds basic support. the bootloader on these units is locked down.
until we have a replacement we can do basic testing with these env variables in uboot.
set update_openwrt erase 0xb0020000 0xb073ffff \;tftp 0x81000000 openwrt-lantiq-xway-VG3503J-squashfs.image\;cp.b 0x81000000 0xb0020000 \$(filesize)
set bootcmd cp.b 0xb0020000 0x80002000 0x400000\; go 0x80002000
unfortunatley the bootloader ignores the bootcmd, so autobooting is not possible yet. you need to call "run bootcmd" by hand after each power cycle.
please note that the vdsl firmware is non redistributable. you can find it in the GPL drop that BT provides.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36315 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also refresh the related generic/platform patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36039 3c298f89-4303-0410-b956-a3cf2f4a3e73
EEPROM is an actial serial EEPROM on the WiFi module, therefore we can remove
ralink_eep from the dts.
USB power-enable GPIO turned out to be GPIO #3 (found via probing/brute-force).
PCI works with default settings as long as the vendor bootloader is used.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36030 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch disables the execute-in-place (XIP) support for flash on
lantiq. This has to be disabled since the bus which flash is connected
to does not support unaligned accesses. Resolves data bus errors on
Lantiq routers with Intel command set flash.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35992 3c298f89-4303-0410-b956-a3cf2f4a3e73
user-space support for extracting the EEPROM for the RaLink WiFi is still
missing. Besides this, it's all working.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35990 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch correctly fixes USB on Lantiq ARV7518.
There was a failed attempt on fixing this on r35077 (https://dev.openwrt.org/changeset/35077/).
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35354 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add ath9k eeprom and pci fixup support (again) for linux 3.7.
On linux 3.3, the fixup forced the regdomain to 0x67, causing low TX power.
This patch only corrects checksum, the rest of the EEPROM isn't changed.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35353 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are two different versions of SMC7908A-ISP: R01 and R01A.
R01 has an internal clock for PCI, meanwhile R01A has an external clock.
This fixes: https://dev.openwrt.org/ticket/12884
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35352 3c298f89-4303-0410-b956-a3cf2f4a3e73
Tested only on the wbmr-hp-g300h, could affect/break other devices.
Signed-off-by: Sebastian Mayr <sebastian.mayr@student.uibk.ac.at>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34837 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Luka Perkov
Jonas Gorski
Gabor Juhos
Steven Barth
Felix Fietkau
Jo-Philipp Wich
Mirko Vogt