Commit Graph

313 Commits (e7ec7a08aae0afb1064d1bf26a9cd6fe1e64d516)

Author SHA1 Message Date
Daniel Golle 083ef3fefe ramips: add support for Mercury MAC1200R v2
MT7628AN + MT7612E, 8MB SPI flash, 64MB DDR RAM
reset button GPIO is still missing (anyone?)
bootloader password is 'slp'

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2016-09-09 02:38:06 +02:00
Mathias Kresin bcd2113a32 ramips: TEW-691GR: fix switch and wireless
Due to the missing phy-mode setting, the switch wasn't initialised.

The wireless requires an eeprom to work. Use the same mac addresses as
the stock firmware.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:47:25 +02:00
Mathias Kresin a7c6cf5182 ramips: TEW-692GR: fix switch and wireless
The AR8327 initvals were not copied to the DTS during the switch from
mach file to device tree and broke the switch on the device.

The former used PORT6 related initvals were wrong and have been
corrected.

The phy mode setting for the switch was missing in the DTS as well.

The wireless requires an eeprom to work. The dual band wireless chips
have both bands enabled by default but only one band per chip is
working.

The stock firmware uses the following mac addresses:

LAN:    AA:BB:CC:DD:EE:E4
WAN:    AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
5 GHz:  AA:BB:CC:DD:EE:E8

Assuming the mac address range :E4 to :E8 is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:

LAN:    AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
WAN:    AA:BB:CC:DD:EE:E5
5 GHz:  AA:BB:CC:DD:EE:E8

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-20 11:45:45 +02:00
Chuanhong Guo 0f73801f4f ramips: Add support for Thunder Timecloud
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2016-08-10 03:04:08 +02:00
Jimmy Zhong 2b1f4945b1 ramips: Add support for TEW-714TRU
Signed-off-by: Jimmy Zhong <mb300sd@mb300sd.net>
2016-08-10 03:03:50 +02:00
P.Wassi 686617ae39 ramips: Rename TP-Link Archer C50 LEDs
Rename LEDs in TP-Link Archer C50 from [manufacturer name]
to [board name] ("tp-link" -> "c50")

Signed-off-by: P.Wassi <p.wassi@gmx.at>
2016-07-26 08:39:36 +02:00
P.Wassi dbf107cd2b ramips: Improve TP-Link Archer C20i support
Improve / finalise TP-Link Archer C20i support.

Signed-off-by: P.Wassi <p.wassi@gmx.at>
2016-07-26 08:39:36 +02:00
P.Wassi 525b9edc8a ramips: unify etc/board.d/01_leds configuration
Introduce an optional parameter at the local set_usb_led and
set_wifi_led function such that they can take a triggering
device. If no parameter is passed, behaviour is unchanged.
Signed-off-by: P.Wassi <p.wassi@gmx.at>
2016-07-24 06:38:30 +02:00
Michael Lee 0d5277f73f ramips: dch-m225 don't have ethernet. default enable wifi
Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-24 06:38:30 +02:00
Paul Wassi 104114fe00 ramips: remove indentation in etc/board.d/01_leds
Remove indentation at end of line in base-files/etc/board.d/01_leds
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-07-24 06:38:29 +02:00
Michael Lee c3e420f28c ramips: Add support for D-Link DCH-M225
D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash,
3.5mm audio out support. but no ethernet and usb ports.
so you must default enable wifi.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-07-11 14:19:47 +02:00
L. D. Pinney cf8c77be6b ramips: Add support for the NixCore X1 Module
The NixCore X1 is a Ralink/MediaTek rt5350 WiFi Module.

http://nixcores.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Drew Gaylo <drew@nixcores.com>
2016-07-11 14:19:47 +02:00
John Crispin eca1021e5c ramips: fix buffalo wmr-300 lan port
Signed-off-by: John Crispin <john@phrozen.org>
2016-07-05 22:59:14 +02:00
Matthias Schiffer 0a0caa2656
ramips: set correct LAN/WAN MAC addresses on DIR-860L B1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Matthias Schiffer 103ed00cfb
ramips: add button support and make LEDs known to userspace for DIR-860L B1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Matthias Schiffer fa9811814a
ramips: fix fixseama call on first boot
Commit "kernel: mtdsplit: calculate kernel partition precisely for Seama"
changed the kernel partition to only contain the kernel itself and not
the Seama header. Adjust the fixseama call to match what is used on
brcm53xx.

This fixes failing to boot a second time after flashing the factory image
on the affected devices.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2016-06-30 17:12:38 +02:00
Roger Pueyo Centelles 5fba0f0c0c ramips: add suport for ZBT APE522II
The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has
64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with
802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac
MT7612E-based 5 GHz radio.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-06-22 19:32:06 +02:00
Henryk Heisig 75af981239 ramips/base-files: Add support for Archer C50
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-13 22:51:43 +02:00
Michael Lee 9a4935687d ramips: add support for DuZun DM06
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.

Signed-off-by: Michael Lee <igvtee@gmail.com>
2016-06-13 22:51:43 +02:00
Yuan Chenmang b38296f2f6 ramips: add Widora-NEO board support
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.

Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-01 12:52:28 +02:00
Cezary Jackiewicz af1e70b4a7 ramips: Add status led for Xiaomi MiWiFi Nano
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-23 22:43:37 +02:00
Cezary Jackiewicz 2965430999 ramips: cleanup for Hame MPR-A2
- disable all ethernet ports except port 0 on MPR-A2

Port 0 is the only ethernet port on this router, so disable all other PHYs in order to save power.

- don't use a VLAN for the single ethernet port of the MPR-A2

Like A5-V11, this router only has one ethernet port.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-23 11:03:23 +02:00
Felix Fietkau 5166732a4e ramips: use green power LED as status indicator for Buffalo WSR-1166 and WSR-600
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-21 15:16:37 +02:00
Andrew Yong 8c9b8d70b1 ramips: add status led for ZBT-WE826
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-05-12 03:29:36 +02:00
Andrew Yong 374cae9e6f ramips: add initial support for SamKnows SK-WB8
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-05-12 03:29:35 +02:00
Vittorio Gambaletta (VittGam) 1570277094 ramips: Fix alphabetical sorting for 02_network
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2016-05-10 10:43:13 +02:00
Vittorio Gambaletta (VittGam) 39f035fdc7 ramips: Don't use a VLAN for the single ethernet port of the A5-V11.
This router only has one ethernet port, so a VLAN is useless here, now that the rt3050 TCP bug that happened without VLANs has been fixed for a very long time.

Add this router to the VLAN-less config that is used by other single-port routers.

Also fix MAC address detection code since this router has no WAN port.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2016-05-10 10:43:13 +02:00
Vittorio Gambaletta (VittGam) ffb7bf7672 ramips: Fix network for routers without VLANs on eth0.
Some routers only have one port, so eth0 is used without VLANs for them.

Revision r47720 introduced some changes, but wrongly confused "enable" with "reset".

VLANs need to be disabled for those routers, and the switch may be reset.

Fix this, by explicitly disabling VLANs instead of resetting the switch for these routers.

Also merge duplicate configuration for the "m2m".

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2016-05-10 10:43:12 +02:00
blogic 6b0425a187 ramips: add support for Planex MZK-EX750NP.
add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49268
2016-05-10 10:43:12 +02:00
John Crispin dc92917409 image / basefiles: make console password configurable
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
Signed-off-by: John Crispin <john@phrozen.org>
2016-04-18 21:53:07 +02:00
John Crispin cb049e71cd ramips: Add support for the Netgear WNDR3700v5
https://wiki.openwrt.org/toh/netgear/wndr3700

wndr3700v5 uses the single-core dual thread MediaTek MT7621S SoC.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49247
2016-04-26 11:43:53 +00:00
John Crispin 279eeeb744 ramips: add support for Planex MZK-EX300NP
MZK-EX300NP is MT7620A based wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49235
2016-04-26 11:43:06 +00:00
John Crispin e55d86ef32 ramips: add support for Planex CS-QR10
CS-QR10 is MT7620A based IP Camera.

the camera and sound does not work with kernel 4.4.
 - camera chip is sn9c291.
 - sound chip is wm8960.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49234
2016-04-26 11:43:01 +00:00
John Crispin 30fbc1a4d1 ramips: Add support for ZBT WG3526
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.

v1->v2:
* Remove some references to 2626 that I had missed in the dts.

v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>

SVN-Revision: 49213
2016-04-21 19:47:08 +00:00
John Crispin 37b50fdb92 ramips: add support for ELECOM WRH-300CR
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.

it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>

SVN-Revision: 49211
2016-04-21 19:46:59 +00:00
John Crispin 890eb0c126 ramips: fix support Planex MZK-750DHP.
fix script for Planex MZK-750DHP.
modification of the GPIO definition.
add Profile.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 49205
2016-04-20 17:19:05 +00:00
John Crispin cc82da0bc1 ramips: MiWifi-Nano - change gpios to leds, add to default build group
1) Use leds to indicate:
Red - Power
Amber - Radio On
Blue - Wifi associated
2) Add profile to default build group for MT7628 subtarget

Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>

SVN-Revision: 49045
2016-03-20 14:41:33 +00:00
John Crispin 99414dbcf1 ramips: Add support for Xiaomi MiWiFi Nano
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash

Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>

v3  includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds

SVN-Revision: 49024
2016-03-16 09:26:48 +00:00
John Crispin be79629259 ramips: Add support for GL-MT750
This patch adds support for GL-MT750.
GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps.
It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support.

SVN-Revision: 48994
2016-03-10 19:12:10 +00:00
John Crispin be53e5a154 ramips: Add support for GL-MT300N
This patch adds support for GL-MT300N.
GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM,
2 LANs, USB, UART, GPIO and PoE support.

SVN-Revision: 48993
2016-03-10 19:12:04 +00:00
John Crispin 96ee39b184 ramips: Add support for GL-MT300A
This patches adds support for GL-MT300A.
GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
Two LANs, USB, UART and MMC daughter board.

SVN-Revision: 48992
2016-03-10 19:11:57 +00:00
John Crispin 1b9985cfe2 ramips: add support for Planex MZK-WDPR.
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 48968
2016-03-08 18:11:59 +00:00
John Crispin 43dd2b9965 ramips: Add JCG routers to base-files
This patch adds support for JHR-N805R, JHR-N825R and JHR-N926R to
various scripts in the base-files directory.

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48905
2016-03-04 08:33:09 +00:00
John Crispin e4dc6acd31 ramips: Incorrect file mode change
Commit d0f5ab6d95a1 ("ramips: Added support for ZBT-826 / ZBT-1026")
incorrectly changed the mode of the ramips shell scripts from 755 to 644.
I.e., they are not excutable any more and for example devices will be left
with broken configs.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>

SVN-Revision: 48893
2016-03-03 20:24:45 +00:00
John Crispin 96eb5c6fa8 ramips: Added support for ZBT-826 / ZBT-1026
Support for these MT7620-based routers: https://wiki.openwrt.org/toh/zbt/we-826
Based on Oskari’s patches found here: https://dev.openwrt.org/ticket/19996

Signed-off-by: Jamie Stuart <jamie@onebillion.org>

SVN-Revision: 48865
2016-03-01 09:17:06 +00:00
John Crispin 8b38a9450b ramips: Add support for Phicomm PSG1208
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

SVN-Revision: 48721
2016-02-15 18:45:22 +00:00
John Crispin 9f9682a79b ramips: Add support for Netgear EX2700
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.

What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48698
2016-02-12 08:29:33 +00:00
John Crispin de7dce21a3 ralink: add WRTnode2 platform and led support
Signed-off-by: xzmu <xzmu@wrtnode.com>

SVN-Revision: 48049
2016-01-01 21:19:50 +00:00
John Crispin 4e31b2e869 ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
Jo-Philipp Wich 67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00