20b2a4417a
Add support for Ubiquiti UniFi AP
...
SVN-Revision: 23904
2010-11-06 21:08:48 +00:00
91b6c63adc
ar71xx: Set eth1 MAC address from EEPROM for WNDR3700
...
The WNDR3700's art/caldata partition contains three MAC addresses at
offsets 0, 6, and 12, used for eth0/wlan0 (shared), eth1, and wlan1,
respectively. The existing code configures eth1's MAC address by adding
1 to eth0's instead of using the value stored in the EEPROM. This patch
causes the stored value to be used directly. (On my WNDR3700s, the three
stored addresses are all sequential anyway.)
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 23876
2010-11-04 18:46:07 +00:00
fc28e1cd7d
ar71xx: fix the wndr3700 antenna group setting for the first wireless chip (thx, Mark Mentovai)
...
SVN-Revision: 23875
2010-11-04 18:39:49 +00:00
b4e2c09b46
ar71xx: improve the wndr3700 quirks - move most of the code out of ath9k and instead allow the platform device to specify gpio overrides - fixes 5ghz signal strength issues
...
SVN-Revision: 23822
2010-11-03 14:55:53 +00:00
f056c054b9
ar71xx: the ar7240 dsa driver is no longer used, remove it.
...
SVN-Revision: 23577
2010-10-21 18:42:28 +00:00
9e2d1a194d
ar71xx: use the new ar7240 switch driver for tl-wa901nd as well
...
SVN-Revision: 23576
2010-10-21 18:42:22 +00:00
6656450c6d
ar71xx: fix more section mismatches
...
SVN-Revision: 23575
2010-10-21 18:42:16 +00:00
8858d90afe
ar71xx: improve 2.6.36 compatibility. also, instead of adding a forward port patch to the 2.6.36 patches, add a backport patch to 2.6.32
...
SVN-Revision: 23574
2010-10-21 18:42:11 +00:00
a680385396
remove remaining references to dev-ap91-eth.h, patch by Stijn Tintel
...
SVN-Revision: 23451
2010-10-14 23:08:10 +00:00
fc035b3cb6
ar71xx: remove dev-ap91-eth.c. switch its only user (RB-750) to the new switch driver
...
SVN-Revision: 23439
2010-10-14 13:41:42 +00:00
3941621dbc
ar71xx: use the new ar7240 switch driver on the DIR-600-A1 as well ( fixes #7563 )
...
SVN-Revision: 23432
2010-10-14 00:14:59 +00:00
b61a804bf7
ar71xx: increase rb4xx nand kernel partition size (patch by danimo)
...
SVN-Revision: 23293
2010-10-07 14:27:34 +00:00
697f5d0bdd
ar71xx: initial support for jjPlus JWAP003
...
Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>
(the GPIODEV code has been removed, the sysfs interface
can be used to control the GPIO lines instead - juhosg)
SVN-Revision: 23165
2010-10-01 07:09:29 +00:00
8511c6b16c
AP96: Fix LAN/WAN setup
...
LAN (eth0) is behind a switch and the fixed speed/duplex was
supposed to be for it, not WAN (eth1).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
SVN-Revision: 23147
2010-09-28 22:55:14 +00:00
32d12d5e5c
ar71xx: add support for the TL-MR3420 v1 board
...
SVN-Revision: 23136
2010-09-27 14:53:59 +00:00
b831ebdde9
ar71xx: AR724[12] requires different USB setup
...
SVN-Revision: 23135
2010-09-27 14:53:57 +00:00
cda8655910
ar71xx: use the MDIO interface of the 2nd MAC on the ar7241
...
SVN-Revision: 23132
2010-09-27 14:53:49 +00:00
b445943cdf
ar71xx: move ath9k specific PCI fixup into a separate file
...
SVN-Revision: 23131
2010-09-27 14:53:46 +00:00
4ae167959b
ar71xx: use different address in ap91_pci_fixup for the AR724[012] SoCs
...
With this change ath9k can handle the wireless chip on the TL-WR841N v7
board which is based on the AR7241 SoC.
SVN-Revision: 23130
2010-09-27 14:53:43 +00:00
a7bb7dd99e
Add support for Atheros AP96 reference board
...
This is still preliminary and not really tested much. Anyway, this
version seems to be enough to get both wired and wireless
interfaces working. Buttons and leds are also working.
mach-ap96.c is based on mach-wndr3700.c.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
SVN-Revision: 23125
2010-09-27 08:59:53 +00:00
0c6653c6e2
ar71xx: select AR71XX_DEV_DSA when AR71XX_DEV_AP91_ETH is selected, do not select AR71XX_DEV_AP91_ETH for TL-WA901ND and TL-WR741ND
...
SVN-Revision: 22935
2010-09-05 16:17:06 +00:00
b4336a8e2d
ar71xx: add support for the Zcomax ZCN-1523H-2-8/5-16 boards
...
SVN-Revision: 22882
2010-09-03 18:14:37 +00:00
47f8fd1dde
ar71xx: rewrite SPI drivers for the RB4xx boards
...
* add a new SPI controller driver
* add SPI driver for the CPLD chip
* convert the NAND driver
* enable the mikroSD slot
* enable more LEDs
SVN-Revision: 22863
2010-08-31 20:13:47 +00:00
7bc5a672c1
ar71xx: change mac address initialization
...
SVN-Revision: 22700
2010-08-18 16:00:28 +00:00
523fcf0497
ar71xx: add a new driver for the ar7240 switch using swconfig. hooks directly into the ethernet driver, as MAC resets also require switch reinitializations and the switch is part of the cpu core anyway switch only tl-wr741nd (and other devices using this board file, such as tl-wr841nd) over to using this by default, as other devices are still untested fixes #7563
...
SVN-Revision: 22675
2010-08-16 19:21:57 +00:00
65899cfa49
ar71xx: remove the fifo cfg overrides for the ap91 ethernet code - these values have been wrong on every single device i've tested, falling back to the atheros values seems to be the right thing to do
...
SVN-Revision: 22401
2010-07-27 21:04:43 +00:00
900aaa919b
ar71xx: add support for the tp-link tl-wa901nd devices (patch by Pieter "Fate" Hollants, from #7528 , without the ethernet fifo cfg values)
...
SVN-Revision: 22353
2010-07-22 12:37:44 +00:00
bced5d7d74
ar71xx: set default values for the fifo cfg registers on AR724x
...
SVN-Revision: 22303
2010-07-20 01:54:11 +00:00
4bb11f9a39
generic: move ath5k_platform.h from ar71xx to generic files
...
SVN-Revision: 22189
2010-07-15 07:36:58 +00:00
95e09cccd8
ar71xx: in-flash macs and eeprom for mach-eap7660d
...
This adds in-flash mac-addresses and calibration data for the Senao
EAP7660D board.
Signed-off-by: Daniel Golle <daniel.golle@gmail.com>
SVN-Revision: 22187
2010-07-15 07:36:52 +00:00
a27ea45e76
ar71xx: only reinit the ethernet MAC at .open() on ar724x for now, until we've figured out what part of it causes the issue described in #7563
...
SVN-Revision: 22075
2010-07-06 12:40:07 +00:00
15b209d09f
ag71xx: reset the hardware during open(), this improves recovery from tx timeouts on ar724x considerably
...
SVN-Revision: 22055
2010-07-04 02:15:08 +00:00
89da22d1ea
ag71xx: fix a memory corruption bug that happens if you flood the interface with packets while it's being brought down fixes boot time crashes under load reported by matteo
...
SVN-Revision: 22054
2010-07-04 01:31:33 +00:00
5a28fb88a4
ar71xx: fix leds-rb750 build failure on 2.6.34
...
SVN-Revision: 22016
2010-07-01 14:49:06 +00:00
7bff9c0101
ar71xx: add support for the Senao EAP7660D board
...
This patch adds support for the Senao EAP7660D board to trunk.
Signed-off-by: Daniel Golle <daniel.golle@gmail.com>
SVN-Revision: 21837
2010-06-18 16:22:05 +00:00
08c2e29018
ar71xx: avoid duplicated 'board' parameter in kernel command line
...
SVN-Revision: 21805
2010-06-14 20:02:44 +00:00
9789f0215a
ar71xx: nuke AR71XX_MACH_UBNT_AR71XX machtype
...
SVN-Revision: 21764
2010-06-12 13:20:39 +00:00
adb0a95df1
ar71xx: fix phy_mask for the RB450
...
SVN-Revision: 21743
2010-06-09 19:48:35 +00:00
6ce447427c
ar71xx: fix build error in the rb{4xx,750}_nand drivers on 2.6.34/35
...
SVN-Revision: 21736
2010-06-09 15:31:34 +00:00
d55ebf3a8a
ar71xx: fix phy_mask on the RB433 for the IP17xx driver
...
SVN-Revision: 21728
2010-06-08 20:19:18 +00:00
90e2b1ad6b
ar71xx: fix 2.6.34 build errors
...
SVN-Revision: 21698
2010-06-07 09:18:13 +00:00
115f845e53
ar71xx: fix nbg460n mtd partitions
...
This fixes the NBG460N/550N/550NH mtd partitions.
Signed-off-by: Michael Kurz <michi.kurz@googlemail.com>
SVN-Revision: 21443
2010-05-14 08:37:58 +00:00
fca9b7ebad
ar71xx: remove config partition from the mtd map on the MZK-W300NH board
...
This space can be used to extend the rootfs_data partition.
SVN-Revision: 21173
2010-04-26 18:28:04 +00:00
77b2354fcd
ar71xx: fix firmware partition size on the MZK-W04NU board
...
SVN-Revision: 21172
2010-04-26 18:28:01 +00:00
7966004d99
ag71xx: remove rx alignment code for small packets, it seems to break ipv6 for some reason ( fixes #7236 )
...
SVN-Revision: 21166
2010-04-26 16:39:13 +00:00
9848d38aed
ar71xx: fix a wifi card stability issue
...
when we receive a pci/ahb interrupt, we need to flush pending data for dma
from the device, otherwise the tx path may get stuck if the completion flag
of the dma descriptor is not updated at the time the tx interrupt arrives.
SVN-Revision: 21143
2010-04-24 17:24:11 +00:00
10ed3b23a6
ar71xx: reduce button threshold value on the NBG460 board
...
SVN-Revision: 21076
2010-04-21 19:07:23 +00:00
9933d34770
ar71xx: use KEY_RESTART and KEY_WPS_BUTTON code for the appropriate buttons
...
SVN-Revision: 21075
2010-04-21 19:07:19 +00:00
693ea524c1
ar71xx: adding support for zyxel nbg460n/550n/550nh boards
...
This patch adds support for the zyxel nbg460n/550n/550nh routers.
Currently this only works if a second stage bootloader is also flashed,
as the used switch needs extra initialization.
Signed-off-by: Michael Kurz <michi.kurz@googlemail.com>
SVN-Revision: 20990
2010-04-18 16:24:12 +00:00
1c0e751391
ar71xx: fix up alignment handling
...
- on ar724x, rx buffers can be aligned with an offset of 2, which keeps the ip header aligned
- alignment offset is only added if the ar8216 workaround is not active and the phy driver does not advertise its own packet alignment
- ar71xx and ar91xx can not handle rx alignment offsets, however taking a hit on unaligned exceptions seems to have less overhead than re-aligning the data for large packets
- use memmove to re-align small packets, if necessary
tested on ar9132, ar7240 and ar7242 based devices without ar8216 headers
SVN-Revision: 20892
2010-04-15 23:31:17 +00:00
Claudio Mignanti
Felix Fietkau
Jo-Philipp Wich
Gabor Juhos