Increase the Kernel partition to address the issue discussed here
https://forum.openwrt.org/t/cpe610-v1-sysupgrade-bin-missing-too-big/39637/5
Switch Back to the okli Loader to support increased partition size
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [add <> for e-mail]
TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- Based on the same underlying hardware as the TP-Link CPE510
- Power, LAN, WLAN5G green LEDs
- 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
The first version of this script allowed just 4Mb factory images.
With this patch is possible to set the maximum size of the payload.
For an 8Mb flash, the corresponding maxsize is:
8 * 1024 * 1024 - 5 * 64 * 1024 = 8388608 - 327680 = 8060928
If the -m argument is not set, the default maximum size will be
used for backward compatibility.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
This reverts commit 0111b86f1d as it
breaks on Linux distributions without ed support
./fix-libmath_h: line 1: ed: command not found
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This commit adds the partition layout used by the TP-Link Archer D50
and probably by the TP-Link Archer D7 to mktplinkfw2.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Extended mksenaofw to support new "capwap" header structure.
This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5
firmware.
Note that the factory image format changes for 3.1 and later firmware,
and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the
factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware
will refuse the factory_35.bin file.
Flashing from the Engenius 3.1.0 firmware with the factory_35.bin
firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW")
is only intended as part of the upgrade path to 3.5.5 firmware.
Modified ipq40xx image Makefile to appropriately invoke mksenaofw
with new parameters to configure the capwap header.
Note that there is currently no method to return to factory firmware,
so this is a one-way street.
Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is
to navigate to 192.168.1.1 on the stock firmware and navigate to the
firmware menu. Then copy the URL you have for that page, something like
http://192.168.1.1/cgi-bin/luci/;stok=12345abcdef/admin/system/flashops
and replace the trailing /admin/system/flashops with just /easyflashops
You should then be presented with a simple "Firmware Upgrade" page.
On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox.
Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin,
click "Upgrade" and on the following page select "Proceed".
Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to
use the stock firmware update menu. Choose the
openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click
"Upload" and "Proceed".
The device should then flash the OpenWrt firmware and reboot. Note
that this resets the device to a default configuration with Wi-Fi
disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2
acting as a LAN port with a DHCP server on 192.168.1.x (AP is at
192.168.1.1)
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[sorry, for unfixing the 80-lines eyesores.]
This patch enable gnu99 mode for the nec-enc utility which
fixes the following build-breaking errors on some older
architectures.
nec-enc.c: In function ‘xor_data’:
nec-enc.c:34:2: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < len; i++) {
^~~
nec-enc.c:34:2: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 to compile your code
nec-enc.c: In function ‘main’:
nec-enc.c:101:3: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < n; i++) {
^~~
Spotted-By: Buildbot
Fixes: fac27643f0 ("firmware-utils: add nec-enc")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
nec-enc provides firmware encoding/decoding with model specific key
for NEC devices.
known devices:
- Aterm WF1200CR
- Aterm WG1200CR
- Aterm WG2600HS
usage:
nec-enc -i infile -o outfile -k key
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[checkpatch fixes, marked usage as noreturn, added static function,
moved buf* from stack to the global data segment]
I made a similar change to this here:
https://github.com/openwrt/packages/pull/8159
However, it turns out this did not fix the problem as the problem has to
do with tools/xz and not the xz package. The error is the same and causes
linking errors as can be seen above.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This provides board configuraion tables for various Tegra boards needed
by cbootimage tool to create flashable bootloader images.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tegra BCT and bootable flash image generator/compiler
>From documentation:
This project provides a tool which compiles BCT (Boot Configuration
Table) images to place into the boot flash of a Tegra-based device.
The tool will either:
a) Compile a textual representation of a BCT into a binary image.
b) Generate an entire boot image from a previously compiled BCT and a
bootloader binary.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Specifications:
* SoC: Qualcomm Atheros QCA9533 (650MHz)
* RAM: 64MB
* Storage: 8 MB SPI NOR
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI or TFTP
To get to TFTP recovery just hold reset button while powering
on for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Thanks to robimarko for the work inside the ar71xx tree.
Thanks to adrianschmutzler for deep discussion and fixes.
Signed-off-by: Mario Schroen <m.schroen@web.de>
[Split into DTS/DTSI, read-only config partition in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename, light subject touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is also helpful to add support in ath79.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Some boards with JBOOT have partiton between bootloader
and kernel image. This patch add possibility to change kernel
partition start address.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The cmake bump to 3.14.0 breaks build on all targets. Revert it for now.
This reverts commit a3446257a8.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update CMake to 3.14.0
Refresh patches
Remove inofficial fossies.org and replace with GitHub (link on official site)
Remote 150-C-feature-checks-Match-warnings-more-strictly.patch as it's
a no longer needed backport from upstream.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range
extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros
QCA9558 + QCA9882 + AR8035 platform and is available only on US market.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x 1 Gbps Ethernet (AR8035)
- 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11)
- 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11)
- 2x U.FL connector on PCB
- 2x dual-band PCB antennas
- 1x LED, 2x dual-color LED (all driven by GPIO)
- 3x button (app config, led, reset)
- 1x mechanical on/off slide switch
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x JTAG (8-pin, 1.27 mm pitch) header on PCB
Flash instruction:
Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254,
default credentials: admin/admin).
Warning:
This device does not include any kind of recovery mechanism in U-Boot.
Vendor firmware access:
You can access vendor firmware over serial (RX line requires jumper
resistor in R306 place, near XTAL) with: root/sohoadmin credentials.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Require the word "warning" to appear at the start of a line, after
whitespace, or after a `:`. This is the same that CTest launchers use
to match warnings. It avoids matching "warning" inside file paths.
Fixed in cmake 3.14.0.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Fixes timeouts with trying to access the FTP site.
Also remove mirror2.openwrt.org, which does not keep current tarballs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
gnu date is present in our staging_dir which means squashfskit will fail
to build. Prevent also a race condition if coreutils is build after
squashfskit.
To prevent a race condition, depend on coreutils.
Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
squashfskit is a fork of the squashfs-tools.
squashfskit creates reproducible filesystems and includes
many of the distro patches.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Paul Spooren <mail@aparcar.org>
This makes OpenWrt build an Ext2+Ext4 partitioned image
for the D-Link DNS-313 with two blank partitions, a boot
partition on /dev/sda3 and a rootfs partition on
/dev/sda4.
This uses the methods already used in apm821xx including
the tricks to convert the generated Ext2 filesystem
partition to version 1 so that the firmware bootloader
will properly recognize it.
We patch a bit around the build files to make sure we
get the rootfs size set and that genext2fs is properly
built.
Tested on the D-Link DNS-313.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Fixing and tricksing]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The firmware on the D-Link DNS-313 NAS require two blank
partitions before the boot partition. Support this if
explicitly requested with a "-n" flag.
Tested on the D-Link DNS-313.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Broken out from original patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update mpfr to 4.0.2
Use official site as last resort
Force thread-safety functionality
Refresh patches
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Fix for factory image generation, so that stock firmware will accept the
openwrt image.
Ref: https://forum.openwrt.org/t/support-for-tp-link-archer-c2-v3/15617/17
Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt>
[reword commit message, use correct order for conditions,
trim trailing whitespace]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality
Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.
Use a fixed timestamp within the zip archive to make the images
reproducible.
Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.
Beside all changes, the footer still looks wrong in compare to the
netgear update image.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the option -mt/--mtime to pass a timestamp which is used as filedate
for the containing files.
So far, it isn't used for anything written to the extra fields,
therefore requires the -X (eXclude eXtra file attributes) parameter to
be effective.
Signed-off-by: Mathias Kresin <dev@kresin.me>
One image requires a zip compressed image, so add the zip util found in
the packages feed, and extend it with some useful debian patches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
While we don't need the gnu99 option anymore, we still need to force the
c99 standard to fix the following build error on the build bots:
src/mkdlinkfw.c: In function 'find_auh_headers':
src/mkdlinkfw.c:267:3: error: 'for' loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < header_counter; i++) {
^
src/mkdlinkfw.c:267:3: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 to compile your code
Signed-off-by: Mathias Kresin <dev@kresin.me>
fread() doesn't set errno, ferror need to be used to check for errors.
While at it, check if we read the expect number of elements.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the SOURCE_DATE_EPOCH environment variable if set instead of the
current time. The used timestamp matches the timestamp of the latest
commit this way and make the images reproducible.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop unused function and macros. With the cleanup the gnu extension
typeof isn't used any longer and the gnu99 compile flag can be dropped.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for TP-Link Archer C6 v2 (EU)
Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board
Flash instructions:
Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
This commit adds "hex pattern mode" to xorimage. This mode allows xor
with a hexadecimal pattern that cannot be expressed with ASCII
charactors.
usage (example):
xorimage -i firmware.bin -o firmware.bin.new -p 6A57190601121E4C -x
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (fix checkpatch)
- it appears (at least from OS X verison 10.10, Yosemite) that the
big and little endian defintions have changed.
the older
#include <sys/_endian.h>
#include <architecture/byte_order.h>
reference yielded the following warning:
#define __bswap_16(x) NXSwapShort(x)
^
/usr/include/architecture/byte_order.h:45:1: note: 'NXSwapShort' has been explicitly marked deprecated here
For the new OS X editions, it seems that we need to refer to:
#include <netinet/in.h>
#include <libkern/OSByteOrder.h>
and respectively use 'OSSwapInt16', 'OSSwapInt32', & 'OSSwapInt64', in
place of 'NXSwapShort', 'NXSwapLong' & 'NXSwapLongLong'.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch adds support for TP-Link Archer A7
Specification:
- SOC: QCA9563
- Flash: 16 MiB (SPI)
- RAM: 128 MiB (DDR2)
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) SoC internal
- 5GHz (ac) QCA988x
- USB: 1x USB 2.0 port
- Button: 1x power, 1x reset, 1x wps
- LED: 10x LEDs
- UART: holes in PCB
- Vcc, GND, RX, TX from ethernet port side
- 115200n8
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin
via the Webinterface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the Archer A7
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the tftp
root directory renamed to ArcherC7v5_tp_recovery.bin
2. Connect power cable to Archer A7, press and hold the reset button
and turn the router on
3. Keep the reset button pressed for ~5 seconds
4. Wait ~150 seconds to complete flashing
Changes since first revision:
- Flash instructions using stock image webinterface
- Changed "Version 5" in model string to "v5"
- Split DTS file in qca9563_tplink_archer-x7-v5.dtsi
and qca9563_tplink_archer-a7-v5.dts
- Firmware image is now build with dynamic partitioning
- Default to ath10k-ct
Changes since second revision:
- Changed uboot@0 to uboot@20000 in DTS file
- Fixed ordering issue in board led script
- Specify firmware partition format in DTS file
- Rebased Makefile device definition on common
Device/tplink-safeloader-uimage definition
- Merged switch section in network script
(same configuration as tplink,tl-wdr3600
and tplink,tl-wdr4300)
Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
The ufb tool needs the host UAPI Linux headers from kernel 3.18
or later, remove it for now as it is not used anyway.
Fixes: 4bf5c4395b ("tools/sdimage: update to latest git version")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This includes code cleanups and fixes some portability issues,
compiler warnings about printf arguments etc.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Drop the factory images and the firmware tool to create them. They don't
work any more, since the factory image has an uImage header covering the
whole kernel + rootfs. This way the uImage splitter will not be able to
find the rootfs and the kernel will panic later on.
The factory images were most likely added at a time the board had
distinct partitions for kernel and rootfs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Some packages like libpfring assume the presense of lex, which on some
other systems is a symlink to flex but not all. Symlink flex to fix
compilation.
Arch Linux and Fedora do this as far as I know.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Currently flash from WebIF is broken for Archer C7 v5 EU models as their
SupportList entries are missing.
The added entries originate from TP-Links latest Archer C7 v5 EU
firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
Chnages since 3.2:
b590ad02 version 3.2.1
05e70adf build: fix issues in the generated tarball
7efe0b5d build: fix typo
351e3630 NEWS: update
4fd1fc70 examples: ship them
e02ce4c7 build: minor fixes in doc/
7cab285e CI: maximize chances of errors sooner
86efe282 c++: improve the generated documentation
cf1446dc tests: don't fail if the C++ compiler does not work
e93c40b3 tests: don't disable C++ warnings in C files
eff67391 c++: workaround portability issue
5a0d7802 tests: work around getopt portability issues
f1e0839c doc: -Wzero-as-null-pointer-constant was added to GCC 4.7
3bf429ae examples: #include <cstring> in calc++
f8cadc73 c: provide a definition of _Noreturn that works for C++
bd7aebb8 c: update the definition of _Noreturn
ca8039e6 tests: don't expect the shell to support 'local'
5d07f4f7 bitset: fix warning
e605ad96 build: fix use of gnulib Make variables
50fac71d maint: post-release administrivia
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
asm/byteorder.h & hence __cpu_to_be32() doesn't exist on Darwin
Shamelessly copy some byte swap functions from oseama.c
Acked-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
as indicated in commit c5bf408ed6 "(ramips: fix image generation for mt76x8")
more rework was needed to fix the other issues.
Building on another machine, but using the same arch, showed
the application failing again for different reasons.
Fix this by completely rewriting the application, fixing following found issues:
- buffer overflows, resulting in stack corruption
- flaws in memory requirement calculations (too small, too large)
- memory leaks
- missing bounds checking on string handling
- non-reproducable images, by using unitilized memory in checksum calculation
- missing error handling, resulting in succes on specific image errors
- endianness errors when building on BE machines
- various minor build warnings
- documentation did not match the code actions (header item locations)
- allowing input to be decimal, hex or octal now
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Buildbot fails to generate images for targets also generating a
Sercomm binary with following error:
Opening file: /mnt/ramdisk/koen/firmware/builds/owrt_mt76x8/build_dir/target-mipsel_24kc_musl/linux-ramips_mt76x8/tmp/openwrt-ramips-mt76x8-netgear_r6120-squashfs-factory.img.rootfs.zip
Filesize: 3648606 .
mksercommfw: malloc.c:2427: sysmalloc: Assertion `(old_top == initial_top (av) && old_size == 0) || ((unsigned long) (old_size) >= MINSIZE && prev_inuse (old_top) && ((unsigned long) old_end & (pagesize - 1)) == 0)' failed.
Makefile:287: recipe for target '/mnt/ramdisk/koen/firmware/builds/owrt_mt76x8/build_dir/target-mipsel_24kc_musl/linux-ramips_mt76x8/tmp/openwrt-ramips-mt76x8-netgear_r6120-squashfs-factory.img' failed
Debugging using valgrind shows stack corruption due to a buffer overflow.
The author of the generator assumes the filename ends with "root",
while it should be "rootfs".
Fix this by accounting for the 2 missing characters which solves the build issues.
More work is required to cleanup this source, which will be done later on.
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
These targets are already defined as having a dynamic partition
but the safeloader was not adapted for them.
This causes a build warning for the sysupgrade image being too big.
Targets:
- c58-v1
- c60-v1
- c60-v2
- TL-WR1043 v5
- TL-WR902AC v1
- TL-WR942N V1
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Targets:
- TP-LINK ER355
- TP-LINK C25 V1
- TP-LINK C59 V1
- TP-LINK C7 V4
- TP-LINK C7 V5
Fixes build issues seen due to the kernel being too big
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
As mentioned in commit 5f24933 recent changes on ar71xx (switch to 4.14,
memory compaction, ...) cause an increase in kernel size, making it too
big for RE450.
RE450 images were not build due to the following error message:
os-image partition too big (more than 1572864 bytes): Success
Tested on RE450, device boots and was used to send this patch.
Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Suggested-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[rewrote commit msg keeping it tight + fixed SoB lines]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Go for openwrt passes pkg-config arguments in the format of
pkg-config --cflags -- pkg-name
which in turn will be passed down to the real pkg-config as something
like
pkg-config.real --cflags -- pkg-name --define...
and causes the real pkg-config implementation to missinterpret the given
argument list.
This also helps to fix https://github.com/golang/go/issues/27940
Signed-off-by: Arthur Skowronek <arthur.skowronek@tuta.io>
uscan reports a new CVE now that PKG_CPE_ID was added.
Reordered patches by date.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[re-title commit & refresh patches]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
A new test case was adding in one of the patches fixing a problem, this
also included a change in the test/Makefile.am to add this test case.
The build system detected a change in the Makefile.am and wants to
regenerate the Makefile.in, but this fails because automake-1.15 is not
installed yet. As automake depends on patch being build first, make sure
we do not modify the Makefile.am.
This fixes build problem seen by the build bots.
Fixes: 4797dddfde ("patch: apply upstream cve fixes")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Makefile.am changed and now patch wants to use automake to
regenerate the Makefile.in. Make sure automake was build before we build
patch.
This fixes build problem seen by the build bots.
Fixes: 4797dddfde ("patch: apply upstream cve fixes")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Apply two upstream patches to address two CVEs:
* CVE-2018-1000156
* CVE-2018-6952
Add PKG_CPE_ID to Makefile.
Build tested on apm821xx and ar71xx.
Signed-off-by: Russell Senior <russell@personaltelco.net>
This patch adds a new type of ubiquiti image, the WA image. First seen
on the NanoStation AC loco the generic name implies that we will see
this type of image on more ubiquiti devices thus it makes sense to
implement it in mkfwimage.
The main difference is that WA images are signed. The "END" header has
been replaced by a "ENDS" header followed by a 2048 bit RSA signature.
This signature is not being generated by mkfwimage and filled with 0x00.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
On some systems (Gentoo) configure stage fails because of docbook2man
working with SGML rather than with XML. We don't need xmlwf man pages so
we disable this.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
In addition to the default little-endianness format, I added a mode
so that we can generate firmware with big-endianness format.
example: ELECOM WRC-300GHBK2-I (QCA9563)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The current make-ras.sh image generation script for the ZyXEL NBG6617
has portability issues with bash. Because of this, factory images are
currently not built correctly by the OpenWRT buildbots.
This commit replaces the make-ras.sh by C-written mkrasimage.
The new mkrasimage is also compatible with other ZyXEL devices using
the ras image-format.
This is not tested with the NBG6616 but it correctly builds the
header for ZyXEL factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds a tool to generate a firmware file accepted
by Netgear or sercomm devices.
They use a zip-packed rootfs with header and a custom
checksum. The generated Image can be flashed via the
nmrpflash tool or the webinterface of the router.
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
Add a temporary workaround to compile with glibc 2.28
as some constants were removed and others made private
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Add a temporary workaround to compile with glibc 2.28
as some constants were removed and others made private
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Adds Support for the TP-LINK CPE510 V2.0 by TP-Link.
The hardware is almost the same as the CPE510 V1.0
Follow the same processes as for the CPE510 V1.0
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB
Flash instruction:
- via web UI:
1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
2. Login to router and open the Advanced tab
3. Navigate to System Tools -> Firmware Upgrade
4. Upload firmware using the Manual Upgrade form
- via TFTP:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Keith Maika <keithm@aoeex.com>
Use the new dynamic partition split in tplink-safeloader so we no longer
have to worry about kernel size increases.
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Use the new dynamic partition split in tplink-safeloader so we no longer
have to worry about kernel size increases.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Add support to dynamically split the firmware partition into os-image
and file-system partitions. This is done by replacing those entries in
the partition table with a single unified firmware partition, which is
then split according to actual kernel image size.
The factory image will have the file-system partition aligned to a 64K
erase block, but the sysupgrade image skips this and aligns only the
JFFS2 EOF marker to squeeze out more space.
This should prevent further creeping updates to the kernel partition
size while maximizing space for the overlay filesystem on smaller
devices.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Add an option (-O) to calculate rootfs offset for combined images.
This is needed for the TP-Link mtdsplit driver to locate the rootfs
when the start is not aligned to an erase block. This will be the
case for sysupgrade images produced by tplink-safeloader with upcoming
dynamic partition splitting.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Arvid E. Picciani <aep@exys.org>
122ca37 Rename bits in hostflags to match new identifiers for the hostflags
32c2a3c Change order of identifiers to be ascending with the spr numbers
f7016b5 Remove definitions which are not Broadcom specific
b77c0a3 debug: Fix ordering of HF bits
3f46e61 fwcutter: Add firmware 9.10.178.27
27892ef fwcutter/make: Avoid _DEFAULT_SOURCE warning
Signed-off-by: Krystian Kozak <krystian.kozak20@gmail.com>
Certain Netgear and AVM devices use BE squashfs for the kernel image. As
squashfs4 only supports creating LE images, add squashfs (v3) into
the tools to be built for ath79.
Trying to use an LE squashfs (thus trying to use squashfs4 only for
building the image) for the kernel image results in the bootloader
barfing and stopping.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Update bison to 3.0.5
Bugfix release
Remove 001-fix-macos-vasnprintf.patch as it is fixed upstream
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
8e29d86 linuxrc: remove superfluous shebang line
12d2045 gitignore: remove Windows stuff
57d8969 Add travis hint
8edf4cc sdimage: use fsync before closing the device (fixes#1)
d395b31 uuc: fix some compiler warnings
Signed-off-by: Krystian Kozak <krystian.kozak20@gmail.com>
Our pkg-config wrapper relies on the ability to redefine the $prefix and
$exec_prefix variables in order to construct proper search paths relative
to the build environment.
Patch the .pc file template to construct libdir, sharedlibdir and includedir
relative to the ${prefix} variable so that it can be overridden as needed.
This also fixes the libxml2/host build issue raised at
https://github.com/openwrt/packages/issues/6073 - it was caused by libxml2's
configure picking up a wrong host search path through zlib.pc, letting it
include the wrong endian.h, causing spurious member redeclaration errors in
system headers.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The default image does not fit 2 MB anymore, expand os-image partition
to 4 MB.
Upgrading works transparently via sysupgrade in both directions.
Another option would have been to merge "os-image" and "rootfs" into a
single "firmware" partition using MTD_SPLIT_TPLINK_FW, but just
changing the sizes of the existing partitioning has been deemed safer
and actually tested on an affected device; the maximum for rootfs
changes from 27 MB to 25 MB.
Run-tested on TP-Link Archer C2600.
Signed-off-by: Joris de Vries <joris@apptrician.nl>
[slh: extend comments and commit message, rename rootfs]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
This tool is used to create headers on images for the
D-Link DNS-313 in gemini target.
Will be used after switching gemini to 4.14 kernel.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MacOSX does not support "-Wl,-Bstatic" so do not force the static
linking.
We only copy the static libz library into the staging libraries
directories, the linker will anyway only find the static version and
link against that on all systems.
Fixes: 8dcd941d8b ("tools/zlib: move zlib build to tools")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Libressl version 2.7.0 and later implement more of the OpenSSL 1.1 API
and this needs some modifications of the code using it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This version now uses autotools to configure the build system. They are
also using the newly added zlib package.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
These functions are not declared in any header file and only used in
same compile unit, mark them as static to remove one gcc warning and
make it easier for the compiler to optimize them out.
This also fixes some style problems to make this patch match the version
in the packages folder.
This is copied from this commit to the mtd-utils we pack into the image:
56d0dd56e9 ("mtd-utils: Mark some lzma functions as static")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This allows us to link the other tools against our libz and we do not
need the system zlib any more.
Only the static linked library is copied to the staging directory so we
have a statically linked library on all systems and not only on Linux.
This also adds the new dependencies of the packages which are depending
on zlib.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The new mkimage version requires a CONFIG_MKIMAGE_DTC_PATH variable to be
provided during build, in order to hardcode a path to a suitable DT
compiler executable.
Failure to do so will result in stray "sh: 1: -I: not found" errors when
invoking mkimage for FIT image generation.
Fix the issue by supplying "dtc" as CONFIG_MKIMAGE_DTC_PATH value during
build. As we intend our host utilities to be relocatable and since we're
already overriding PATH when invoking mkimage, an absolute path is not
required.
Fixes: b13e981d72 ("tools/mkimage: update to version 2018.03")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This activates support for fit images and some other new mkimage
features. Some of the patches were applied upstream and could be
removed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update cmake to 3.11.0
Remove 110-alpine_musl-compat.patch as it's integrated upstream
Rename and refresh patches
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Having the metainfo between kernel and rootfs prevents us from resizing
the kernel partition as necessary.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
TP-Link Archer C60 v2 is a dual-band AC1350 router, based on
Qualcomm/Atheros QCA9561 + QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (web):
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use
OEM System Tools - Firmware Upgrade site.
Flash instruction (recovery):
1. Set PC to fixed IP address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and
rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
Flash instruction (under U-Boot, using UART):
tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Andrew Cameron
Daniel Engberg
Deng Qingfang
Davide Fioravanti
Hans Dedecker
Steve Glennon
Tomasz Maciej Nowak
Christian Lamparter
INAGAKI Hiroshi
Rosen Penev
Michael Gray
Mario Schroen
Adrian Schmutzler
Pawel Dembicki
Stijn Tintel
Piotr Dymacz
Daniel Golle
Moritz Warning
Felix Fietkau
Alexander Couzens
Syrone Wong
Linus Walleij
Skirmantas Lauzikas
David Bauer
Kuang Rufan
Mathias Kresin
Egor Mikhaylov
Georgi Vlaev
Kevin Darbyshire-Bryant
Karl-Felix Glatzer
Hauke Mehrtens
Michael Heimpold
Ted Hess
Koen Vandeputte
Hannu Nyman
Thorsten Glaser
Radek Dostál
Arthur Skowronek
Russell Senior
Tobias Schramm
Marko Ratkaj
Ryan Mounce
Andy Walsh
Ludwig Thomeczek
Luis Araneda
Keith Maika
Hyeonsik Song
Peter Lundkvist
Lucian Cristian
Alex Maclean
Arvid E. Picciani
Krystian Kozak
Zoltan HERPAI
Jo-Philipp Wich
Stefan Lippers-Hollmann
Matthias Schiffer
Henryk Heisig
Nicolò Veronese