b3fdd931d1
ramips: add support for Sitecom WL-341v3 and other Sercomm IP1006RRv2 boards
...
This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 29910
2012-01-26 10:44:23 +00:00
038d4e0d77
ar71xx: TL-MR3020: fix board detection, fix missing mandatory package and modify LED behaviour
...
This patch fixes the board detection of the TL-MR3020.
The LED behaviour has also been modified:
* The WPS LED is the diag LED now.
* A netdev trigger for the LAN LED has been added.
The profile of the TL-MR3020 has been updated because the needed package
"kmod-ledtrig-usbdev" was missing which resulted in a non-working usbdev
trigger for the 3G/USB LED.
[juhosg: the board name changes has been removed, and the kernel files
has been changed instead.]
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29905
2012-01-25 07:44:45 +00:00
c11ac55b29
ar71xx: TL-MR3020: fix GPIO polarity for button and switch
...
This patch fixes the GPIO polarity for the button and the sliding
switch. The buttons are not active low. "Pressed" and "Released"
events are wrong without the patch.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29904
2012-01-25 07:44:43 +00:00
4f3d6c9ae9
ar71xx: use the lzma loader on the Planex boards
...
SVN-Revision: 29900
2012-01-24 20:12:10 +00:00
5fa9768cee
ar71xx: rename Sysupgrade/{KR,RK} to Sysupgrade/{KR,RK}uImage
...
SVN-Revision: 29899
2012-01-24 20:12:08 +00:00
095c236694
ar71xx: fix the AP/Router LED definitons on MZK-W300NH
...
SVN-Revision: 29897
2012-01-24 18:40:38 +00:00
23e1b451dc
ar71xx: preset WLAN LED config on MZK-W300NH
...
SVN-Revision: 29896
2012-01-24 18:40:36 +00:00
23836d5908
ar71xx: remove hardcoded MTD layout from planex files
...
SVN-Revision: 29895
2012-01-24 18:40:34 +00:00
859c915077
ar71xx: pass mtdlayout to Planex boards via command line
...
SVN-Revision: 29894
2012-01-24 18:40:33 +00:00
6ad9bf8d17
ar71xx: remove an unused header file
...
SVN-Revision: 29893
2012-01-24 18:40:31 +00:00
02e77c6ae1
ramips: generate sysupgrade image for the ALL0256N
...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29884
2012-01-24 11:48:48 +00:00
944c8aacdb
ramips: add user-space support for ALL0256N
...
This adds uci-defaults and sysupgrade support for the ALL0256N.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29883
2012-01-24 11:48:47 +00:00
1932a7205c
ramips: add kernel support for ALL0256N
...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29882
2012-01-24 11:48:45 +00:00
17bb003891
ar71xx: nuke fs_all variable in image/Makefile
...
SVN-Revision: 29880
2012-01-24 09:47:25 +00:00
1fb88e2541
ar71xx: create interim kernel files in a separate dir
...
This reduces the size of the ImageBuilder tarball a lot.
SVN-Revision: 29879
2012-01-24 09:47:23 +00:00
a43e2f508f
ar71xx: prebuild all loaders in Image/Prepare stage
...
SVN-Revision: 29878
2012-01-24 09:47:22 +00:00
9cf1d4e06e
ramips: scripts updates
...
In this patch:
* rename Argus leds to avoid underscores
* rename Belkin F5D8235 v1 leds from f5d8234 to f5d8235
* remove Belkin F5D8235 v1 status led defined as storage led (it was
defined as usb led earlier, just in wrong place) - it should have
router led as in v2
* add Argus, Sparklan and Belkin F5D8235 v2 status leds
* add Belkin F5D8235 v1 and v2 usb leds
* fix Belkin F5D8235 v2 network config generation and mac address axtraction
* fix Sparklan board identification
* add Sparklan usb led (this board doesn't have usb connector by
default and the led is hidden also but if you are going to solder
the connector then you'll see the led too)
* add Sparklan network config generation and mac address extraction
* fix empty string test in network script and...
* ...sort case entries by the first board in the list
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29871
2012-01-23 10:23:32 +00:00
44517a3789
ar71xx: 3.2: fix build errors if PCI is not enabled
...
SVN-Revision: 29870
2012-01-23 08:52:21 +00:00
778db0a13d
ar71xx: fix compiler warning if PCI is not enabled
...
SVN-Revision: 29869
2012-01-23 08:52:18 +00:00
af015f956c
ar71xx: add initial support for 3.2
...
Tested on the following boards:
ALFA AP96
TL-MR3220 v1
TL-WR1043ND v1
TL-WR2543ND v1
TL-WR703N v1
TL-WR741ND v1
TL-WR741ND v4
WNDR3700 v1
WZR-HP-G300NH
SVN-Revision: 29868
2012-01-22 22:38:19 +00:00
386cbfe45b
ar71xx: move arch specific files to files-2.6.39
...
SVN-Revision: 29867
2012-01-22 22:38:11 +00:00
7b7427e52c
ar71xx: build ALFA AP96 images with default profile as well
...
SVN-Revision: 29866
2012-01-22 22:33:15 +00:00
dd49cca9d6
generic: 3.2: allow to build myloader mtd parser for ATH79
...
SVN-Revision: 29860
2012-01-22 18:43:39 +00:00
9be1b91644
generic: allow to build myloader mtd parser for 3.2+
...
SVN-Revision: 29858
2012-01-22 18:36:49 +00:00
809fe38e41
ramips fix f5d8235-v1 diag LED support
...
SVN-Revision: 29857
2012-01-22 18:11:39 +00:00
e7dee3aeed
ar71xx: wrt160nl_part: include module.h and fix compiler warnings
...
SVN-Revision: 29856
2012-01-22 17:55:38 +00:00
a7d344565b
ar71xx: tplinkpart: include module.h
...
SVN-Revision: 29855
2012-01-22 17:55:36 +00:00
6c2638c5e2
ar71xx: rename vsc7385 spi driver
...
SVN-Revision: 29853
2012-01-22 13:51:57 +00:00
bb16739db9
ar71xx: rename ap81 spi driver
...
SVN-Revision: 29852
2012-01-22 13:51:56 +00:00
5ef8b922fa
ar71xx: rename rb4xx spi drivers
...
SVN-Revision: 29851
2012-01-22 13:51:54 +00:00
aad175d5b6
ar71xx: rename the nxp_74hc153 driver
...
SVN-Revision: 29850
2012-01-22 13:51:52 +00:00
ef1c53b7b7
ar71xx: change board id of the UniFi board
...
SVN-Revision: 29849
2012-01-22 13:51:50 +00:00
f90e578903
ar71xx: include linux/module.h in the micrel phy driver
...
SVN-Revision: 29848
2012-01-22 13:51:49 +00:00
e9d8deaaed
ramips: add sysled and sysupgrade to wr512-3gn
...
Patch from #10035 .
SVN-Revision: 29847
2012-01-22 13:43:23 +00:00
8e662f28fe
generic: 3.2: don't disable lockdep for OOT modules
...
SVN-Revision: 29846
2012-01-22 09:57:39 +00:00
4625c9b5a4
generic: rtl8366: add rtl8366_smi_write_reg_noack helper
...
After issuing a soft reset on the RT8366{S,RB}
switch, waiting for the last acknowlegement fails
in rtl8366_smi_write_reg. Add a _noack version of
the function and use that for issuing a soft reset.
SVN-Revision: 29844
2012-01-21 22:44:09 +00:00
26d4e1876c
brcm47xx: add support for pcie host controller on bcma based SoCs.
...
This also adds minimal support for the BCMA43224 pcie wireless card.
SVN-Revision: 29843
2012-01-21 22:39:20 +00:00
557cf076b4
ramips: sysupgrade for ESR-9753
...
This patch add sysupgrade for Engenius ESR-9753
Signed-off-by: Artur Wronowski <arteqw@gmail.com>
SVN-Revision: 29824
2012-01-20 10:49:26 +00:00
aa8f9171f2
kernel: fix OCF for linux 3.2
...
Add skb_frag_page from 3.2 to OCF for 3.1 and earlier and use it.
SVN-Revision: 29818
2012-01-19 19:51:54 +00:00
fc512193a0
add missing kernel symbols
...
SVN-Revision: 29790
2012-01-19 01:57:22 +00:00
2fc3fe1d09
Make the grub timeout configurable on x86 targets
...
Signed-off-by: Justus Winter <4winter@informatik.uni-hamburg.de>
SVN-Revision: 29786
2012-01-19 01:14:45 +00:00
095f7f2da3
x86/config-3.2: add linux-3.2 symbols for x86
...
The following symbols are missing for x86, in sorted order.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 29783
2012-01-19 00:31:39 +00:00
dbfeb5d158
fix thinko in 102-ehci_hcd_ignore_oc patch
...
SVN-Revision: 29773
2012-01-18 07:56:02 +00:00
49eb3fd845
gigaset 76x
...
* fixes leds
* adds all leds found on the sx763 board
* removes board_config from flash layout because wireless data is stored in kernel (ath5k)
* fix button handling
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 29763
2012-01-17 12:10:35 +00:00
a2708d11e8
ramips: Rework ramips_eth to not require irqsave locking anymore
...
Previously the tx housekeeping was done in a spin_lock_irqsave critical
section which causes irqs to be disabled during that time. Since the
housekeeping is already prepared to be scheduled as a tasklet process
the housekeeping only in softirq context and revise the locking between
the tx path and the housekeeping tasklet by using a normal spin_lock
which in most situations will be a NOP anyway.
This makes sure that interrupts are only disabled for a short time
since in the worst case the housekeeping might have to free up to 256
skbs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 29762
2012-01-17 11:23:11 +00:00
034cf5643f
brcm47xx: add support for kernel 3.2
...
SVN-Revision: 29756
2012-01-15 21:18:34 +00:00
c3d134af12
brcm47xx: run kernel_oldconfig
...
SVN-Revision: 29755
2012-01-15 14:53:32 +00:00
f9e41adc80
add support for OMAP4 based boards, starting with the PandaBoard
...
SVN-Revision: 29753
2012-01-14 23:02:56 +00:00
6274648199
fixup arm xz support with recent changes
...
SVN-Revision: 29750
2012-01-14 22:55:04 +00:00
e65195c246
add missing symbols
...
SVN-Revision: 29749
2012-01-14 22:53:28 +00:00
b0479e2ca2
kernel: disable bridge igmp snooping in 3.2 as well
...
SVN-Revision: 29747
2012-01-14 14:57:03 +00:00
66895b7115
kernel: disable bridge igmp snooping by default to avoid multicast issues
...
SVN-Revision: 29744
2012-01-14 13:50:25 +00:00
9eb73ee6b7
kernel: ppc40x: ppc44x: add missing kernel config symbol
...
SVN-Revision: 29742
2012-01-14 12:04:17 +00:00
d5bc3a994b
brcm47xx: update usb driver
...
Add workarround for BCM5357 and BCM4749.
This patch contains the following fixes from George Kashperko:
* separate subroutines for controller initialization workarounds -
following CodingStyle recommendations;
* __devinit __devexit __devinitconst annotations for CONFIG_HOTPLUG;
* fix leak in ssb_hcd_create_pdev/bcma_hcd_create_pdev - as hci_res being
kmalloc'ed is never freed anywhere while platform_device_add_resources
will kmemdup resources right away;
* fix compilation error in ssb_hcd_resume - it will fail as soon as
CONFIG_PM is selected.
SVN-Revision: 29734
2012-01-13 20:11:23 +00:00
9d497cb132
rtl8366: fix rtl8366_smi_detect() after r29677
...
SVN-Revision: 29732
2012-01-13 19:17:58 +00:00
3883e71097
brcm63xx: add support for linux 3.2
...
SVN-Revision: 29731
2012-01-13 14:59:50 +00:00
1bc0abb058
kernel: add support for linux 3.2.1
...
SVN-Revision: 29730
2012-01-13 14:55:07 +00:00
f3f1075655
kernel: backport overlayfs v11 to 3.0 and 2.6.39
...
Should fix whiteout issues and missing files when using extroot.
SVN-Revision: 29727
2012-01-13 14:42:53 +00:00
c560444a58
kernel: update linux 3.1 to 3.1.9
...
SVN-Revision: 29726
2012-01-13 14:38:28 +00:00
e49d3e1d5b
kernel: update linux 3.0 to 3.0.17
...
SVN-Revision: 29725
2012-01-13 14:10:44 +00:00
e87bb77966
ar8216: use vlan configuration for connecting ports (forced to be untagged) even with vlan_enable=0, but keep them isolated before the switch has been configured this makes enable_vlan=0 practical for vlan passthrough
...
SVN-Revision: 29719
2012-01-12 10:15:11 +00:00
c33e016fa5
ar8216: do not strip vlan tags when running with vlan_enable=0
...
SVN-Revision: 29718
2012-01-12 10:15:08 +00:00
fbf81c8e79
ar71xx: move irq_to_gpio and gpio_to_irq into gpio.c
...
SVN-Revision: 29713
2012-01-11 18:00:50 +00:00
034b7f0ef5
Remove invalid LED GPIO from GW6200 board definition. GPIO 35 isn't intended to control ethernet LED (the led behaviour is a side effect) and using the gpio as an led causes kernel panics.
...
SVN-Revision: 29712
2012-01-11 13:47:48 +00:00
67f62cf5cf
ar71xx: disable ath79 in order to get rid of Kconfig warnings
...
SVN-Revision: 29711
2012-01-11 09:14:19 +00:00
88d8cdd503
ar71xx: pb44_spi: add shutdown handler
...
This allows to access the flash from a kexec'd kernel.
SVN-Revision: 29710
2012-01-11 09:14:18 +00:00
e1b7995aef
ar71xx: pb44_spi: call pb44_spi_{en,dis}able from probe/remove
...
SVN-Revision: 29709
2012-01-11 09:14:17 +00:00
67444c7795
ar71xx: pb44_spi: introduce pb44_spi_{en,dis}able helpers
...
SVN-Revision: 29708
2012-01-11 09:14:15 +00:00
0f566a376c
ar71xx: ar71xx_spi: add shutdown handler
...
This allows to access the flash from a kexec'd kernel.
SVN-Revision: 29707
2012-01-11 09:14:14 +00:00
09a6e3f662
ar71xx: ar71xx_spi: save and restore regs from probe/remove
...
SVN-Revision: 29706
2012-01-11 09:14:13 +00:00
714a9bd641
ar71xx: ar71xx_wdt: add shutdown handler
...
SVN-Revision: 29705
2012-01-11 09:14:11 +00:00
9727256330
ar71xx: refresh patches
...
SVN-Revision: 29683
2012-01-07 19:36:43 +00:00
4edff7d3ef
ar71xx: add a profile and build images for the TL-WR2543N/ND
...
SVN-Revision: 29682
2012-01-07 19:36:42 +00:00
a1dcbc66a6
ar71xx: add initial support for the TL-WR2543N/ND board
...
The WLAN LEDs are not working yet.
SVN-Revision: 29680
2012-01-07 19:36:35 +00:00
a56bdeff9d
ar71xx: allow to specify max read size for m25p80
...
Reading from the flash chip on the TL-WR2543ND seems buggy.
If the SPI flash driver tries to read too much data in one
SPI transfer, the flash chip returns bogus values. This can
be caused by a buggy flash chip on my board, or it can
be a bug in our SPI driver.
Add a workaround to the m25p80 driver until I find out the
root cause of the problem. The patch allows to specify the
maximum numner of bytes which can be read safely withint
one SPI transfer.
SVN-Revision: 29679
2012-01-07 19:36:33 +00:00
8b567fb508
generic: add driver for the RTL8367R/M switches
...
SVN-Revision: 29678
2012-01-07 19:36:31 +00:00
87fb92ee03
generic: rtl8366: preparing for RTL8367 support
...
* make clock delay configurable
* make read,write commands configurable
* use u16 for member and untag fields
SVN-Revision: 29677
2012-01-07 19:36:30 +00:00
43196813d7
generic: rtl8366_smi: add timeout message
...
SVN-Revision: 29676
2012-01-07 19:36:25 +00:00
67b2814842
ar71xx: local mac support on the wndr3700
...
The wndr3700 at least has no eth0 mac address and usually leverages
the first wireless device's mac when in a bridged scenario. If,
however, you want to route, and not bridge the interfaces, you
need a unique mac address for it.
This patch sets the local bit on the mac address pulled from the
wireless chip and uses the resulting address for eth0.
Patch-by: Dave Taht <dave.taht@gmail.com>
SVN-Revision: 29675
2012-01-07 17:24:44 +00:00
6c74274c8d
generic: improve MIPS kexec support
...
It is based on patches from the linux-longsoon-community git tree:
http://dev.lemote.com/cgit/linux-loongson-community.git/
Now the kernel can use the command line parameter from kexec-tools.
Runtime tested on ar71xx with 2.6.39.4 (the wathdog must be stopped
before executing the new kernel). Compile tested with lantiq (3.1.4)
and brcm47xx (3.0.12).
SVN-Revision: 29674
2012-01-07 16:29:16 +00:00
f638c6207b
ar71xx: fix sysupgrade on the TL-WR841N/ND v7 boards
...
SVN-Revision: 29672
2012-01-06 15:54:59 +00:00
1e848b17ad
ar71xx: add support for Redwave RW2458N
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 29669
2012-01-06 07:20:59 +00:00
84cd8a5ee0
ar71xx: fix RB-750 network configuration
...
SVN-Revision: 29668
2012-01-06 07:20:54 +00:00
8eb0b7ab3d
ar71xx: fix sections mismatch warnings in the nand drivers
...
SVN-Revision: 29667
2012-01-05 18:08:33 +00:00
232eb83f74
ar71xx: fix LED configuration on the RB-750
...
SVN-Revision: 29666
2012-01-05 18:08:28 +00:00
d65c6fe720
ar71xx: create profile and build image for the ALFA AP96 board
...
SVN-Revision: 29663
2012-01-04 21:13:57 +00:00
b8f0d86115
ar71xx: add inital support for the ALFA Network AP96 board
...
The microSD slot and the Real Time Clock is not working yet.
The miniPCIe interface is not tested due to the lack of a
suitable card.
SVN-Revision: 29662
2012-01-04 21:13:54 +00:00
807e046193
ar71xx: specify console kernel parameter for the Compex boards
...
SVN-Revision: 29660
2012-01-04 17:30:59 +00:00
923f3e3752
ar71xx: allow to use the command line hack on compex devices
...
SVN-Revision: 29659
2012-01-04 17:30:58 +00:00
2f53f82203
ar71xx: use the TL-MR3x20 code for the TL-WR841N/ND v7
...
These models are based on the AP99 reference board,
and uses the AR7241 SoC.
SVN-Revision: 29658
2012-01-04 17:30:57 +00:00
301b1b4f92
ar71xx: show correct model name on TL-WA701N/ND boards
...
SVN-Revision: 29657
2012-01-04 17:30:55 +00:00
ac68f0d8fa
ar71xx: add profile and build image for the TL-WA701N/ND boards
...
SVN-Revision: 29656
2012-01-04 17:30:54 +00:00
72019009c7
ar71xx: fix network configuration for the TL-WA901N/ND boards
...
SVN-Revision: 29654
2012-01-04 17:30:52 +00:00
90bfef9ec9
ar71xx: allow to use LAN LED on the TL-WA901N/ND boards
...
SVN-Revision: 29653
2012-01-04 17:30:50 +00:00
5eb502d9c1
ar71xx: add default LED configuration for the TL-MR3020
...
Also use the system LED for diagnostic.
SVN-Revision: 29652
2012-01-04 17:30:49 +00:00
1045c83527
ar71xx: add support for TP-Link TL-MR3020
...
This patch adds support for the TP-Link device TL-MR3020 which is very
similiar to the TL-WR703N.
The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions.
Only four LEDs can be controlled via GPIO. The power LED is connected to
the power supply.
The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals
of the sliding switch have been mapped to BTN_0 and BTN_1.
I have also setup a wiki page with details here:
http://wiki.openwrt.org/toh/tp-link/tl-mr3020
USB is working and has been tested with USB mass storage and USB UMTS
stick.
Wifi also seems to work.
Ethernet is working too.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29651
2012-01-04 17:30:47 +00:00
88223f87d1
ar71xx: use the new om-watchdog package for OM2P
...
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
SVN-Revision: 29648
2012-01-04 17:30:41 +00:00
a788f199c9
remove current RTSP support
...
SVN-Revision: 29643
2012-01-04 00:29:29 +00:00
237282ae8c
backport upstream commit e1738bd9cecc5c867b0e2996470c1ff20f66ba79 to affected kernels ( #9802 ) commit 8efa88540635 (sch_sfq: avoid giving spurious NET_XMIT_CN signals) forgot to call qdisc_tree_decrease_qlen() to signal upper levels that a packet (from another flow) was dropped, leading to various problems.
...
SVN-Revision: 29642
2012-01-03 23:08:15 +00:00
8854c90119
ar71xx: add profile and build factory image for the Hornet-UB board
...
SVN-Revision: 29637
2012-01-01 19:30:29 +00:00
1d3de89f3c
ar71xx: build images for the ALFA Network N2/N5 boards
...
SVN-Revision: 29636
2012-01-01 19:30:28 +00:00
1e68f10b87
ar71xx: add support for the ALFA Network N2/N5 boards
...
SVN-Revision: 29635
2012-01-01 19:30:25 +00:00
5c067db8a7
ar71xx: define LAN/WAN LEDs for the TL-WR741N/ND boards
...
SVN-Revision: 29631
2011-12-31 15:02:46 +00:00
fff02e6ea8
ar71xx: enable SWCONFIG_LEDS
...
SVN-Revision: 29630
2011-12-31 15:02:40 +00:00
5fa65cba6e
kernel: swconfig: introduce a generic switch LED trigger
...
SVN-Revision: 29627
2011-12-31 15:02:30 +00:00
8c2482f76e
ar71xx: ag71xx: implement get_port_{link,stats} callbacks
...
SVN-Revision: 29626
2011-12-31 15:02:26 +00:00
975355a2b1
kernel: swconfig: add get_port_{link,stats} callbacks
...
SVN-Revision: 29625
2011-12-31 15:02:24 +00:00
557009bbdb
ar71xx: fix LEDs on the WRT400N
...
SVN-Revision: 29624
2011-12-31 13:54:11 +00:00
244c322d25
ramips: rt288x: add support for the Belkin F5D8235-4 v1 board
...
Patch-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 29617
2011-12-28 08:43:43 +00:00
f50b02b559
ramips: rt288x: change base address and window size of flash bank 0
...
SVN-Revision: 29616
2011-12-28 08:43:36 +00:00
98437278c4
ramips: rt305x: add support for the ALFA Networks W502U (R36) board
...
SVN-Revision: 29615
2011-12-28 08:43:32 +00:00
76dacee995
ar71xx: enable sysupgrade support for airrouter
...
Works for me! ;-)
Patch-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 29614
2011-12-27 16:59:43 +00:00
c6ee919b2a
ar71xx: fix sysupgrade on PB42/PB44 boards
...
SVN-Revision: 29613
2011-12-27 16:57:01 +00:00
723d8dd74f
ramips: rt288x: add support for the Buffalo WLI-TX4-AG300N board
...
SVN-Revision: 29612
2011-12-27 16:56:30 +00:00
9fa33ceee2
add missing config symbol
...
SVN-Revision: 29610
2011-12-25 13:33:18 +00:00
11125d68ed
brcm47xx: fix usb on more recent bcma based devices.
...
SVN-Revision: 29605
2011-12-23 17:21:52 +00:00
7b1e525b56
ramips: initial support for Sitecom WL-351 v1 002
...
This add support for the Sitecom WL-351 v1 002.
In principle the Engenius ESR9850 should also work with this, but I
don't have the hardware to test it.
Since an external gigabit switch (RTL8366RB) is used,
I had to modify the ramips_esw driver to add a 'bypass' mode, which
just configures it to not filter the vlan tags.
Also two initialization words (FCT2 and FPA2) are set to different
values by u-boot than what the driver is using and it only seems to
work correctly when they not overridden by the driver, so I
added them to the platform specific data as reg_initval_fct2 and
reg_initval_fpa2.
With this wired lan works as expected, however I'm still having some
trouble with the wireless lan:
It only works after I rmmod & re-insmod rt2800pci and then
reconfigure it in the webinterface, but not directly after
rebooting.
The symptom of this is wpad saying:
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: associated (aid 1)
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> WPA: pairwise key handshake completed (RSN)
Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: authenticated
But wpa_supplicant on the client saying:
Authentication with <wl351mac> timed out.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 29604
2011-12-23 14:27:16 +00:00
2cb946f5b4
ramips: add support for the Senao/EnGenius ESR-9753 board
...
Signed-off-by: Artur Wronowski <arteqw@gmail.com>
SVN-Revision: 29603
2011-12-23 14:27:10 +00:00
03bce34384
ramips: define firmware partition for Omnima MiniEMBWiFi
...
Patch-by: Ivan Ignjatic <ivan@omnima.co.uk>
SVN-Revision: 29602
2011-12-23 14:27:05 +00:00
db0a1db257
ar71xx: set a reserved bit that resets to 1 when writing the address table control register on the ar7240 switch (should fix #10547 )
...
SVN-Revision: 29598
2011-12-22 05:43:53 +00:00
8799627ef0
ar71xx: add default network config for buffalo WZR-HP-G300NH2 and WZR-HP-G450H
...
Thanks netprince for reporting and testing.
SVN-Revision: 29595
2011-12-21 19:32:40 +00:00
ebefe1eb3a
the mach file of the WZR-HP-G300NH2 accidentally claimed the mach id of the WZR-HP-AG300H, correct the id ( #10649 )
...
SVN-Revision: 29593
2011-12-21 01:27:48 +00:00
0cd03df3b1
brcm47xx: remove patch starting adding brcm4716 to ssb
...
brcm4716 is supported by bcma now we do not need this patch
SVN-Revision: 29576
2011-12-19 23:55:20 +00:00
5b8686c303
brcm47xx: add new usb driver for bcma bus and replace ssb usb driver.
...
This new usb driver uses an extra device so the ehci and the ohci driver are not depending on ech other any more.
SVN-Revision: 29575
2011-12-19 23:39:13 +00:00
1aa5a61754
kernel: update bcma and ssb to version master-2011-12-16 from wireless-testing
...
SVN-Revision: 29574
2011-12-19 23:33:03 +00:00
91d0ef6f19
brcm47xx: remove support for kernel 2.6.39
...
There are problems with the patches for kernel 2.6.39 and I do not want to support two different sets of patches.
SVN-Revision: 29573
2011-12-19 23:26:15 +00:00
11013ad947
ar71xx: add missing wireless led changes for wzr-hp-g300nh2
...
SVN-Revision: 29568
2011-12-19 09:04:15 +00:00
0cc056cb7e
ar71xx: add support for the wzr-hp-g300nh2
...
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
SVN-Revision: 29567
2011-12-18 22:20:17 +00:00
5a0a2b2f1b
ar71xx: use 64kraw template on more TP-Link boards
...
SVN-Revision: 29561
2011-12-17 18:49:55 +00:00
67c7980290
ar71xx: connect GMAC0 to the internal switch on DB120
...
Because the external switch has no driver yet, connect GMAC0
to the PHY4 of the internal switch for now. This allows to
use the DB120 board as a router with 4LAN+1WAN ports.
SVN-Revision: 29557
2011-12-15 22:25:38 +00:00
5bbd416e38
ar71xx: add defines for the AR934X GMAC interface
...
SVN-Revision: 29556
2011-12-15 22:25:36 +00:00
e47a8c2bb2
ar71xx: fix GMAC1 interface speed on the DB120 board
...
SVN-Revision: 29555
2011-12-15 22:25:35 +00:00
36bc2c2c80
ar71xx: ag71xx: fix switch port setup for AR934X
...
SVN-Revision: 29554
2011-12-15 22:25:32 +00:00
00667c3846
ar71xx: ag71xx: allow to connect PHY4 to the CPU on AR934X
...
SVN-Revision: 29553
2011-12-15 22:25:30 +00:00
0540970345
ar71xx: ag71xx: setup switch interface mode on AR934X
...
SVN-Revision: 29552
2011-12-15 22:25:29 +00:00
44014110b8
ar71xx: ag71xx: detect the built-in switch of the AR934X SoCs
...
SVN-Revision: 29551
2011-12-15 22:25:28 +00:00
e2a546d475
ar71xx: allow to attach the internal switch for AR934x
...
SVN-Revision: 29550
2011-12-15 22:25:22 +00:00
9ae65588d8
ar71xx: introduce ar71xx_switch_data
...
SVN-Revision: 29549
2011-12-15 22:25:11 +00:00
bfe747b7d9
ar71xx: build images for TL-WR741N/ND v2
...
SVN-Revision: 29548
2011-12-15 22:03:48 +00:00
aefff26624
ar71x: use raw squashfs images for TP-Link boards
...
SVN-Revision: 29547
2011-12-15 22:03:46 +00:00
d5bd28ffae
ar71xx: create a template for using unpadded squashfs images
...
SVN-Revision: 29546
2011-12-15 22:03:45 +00:00
dbc4fa4b5b
ar71xx: put squash image right after the kernel on TP-Link boards
...
SVN-Revision: 29545
2011-12-15 22:03:44 +00:00
850be54b72
ar71xx: tplinkpart: allow to detect JFFS2 as well
...
SVN-Revision: 29543
2011-12-15 22:03:40 +00:00
b7d7481b07
ar71xx: ag71xx: check PHY IDs before accessing the switch registers
...
SVN-Revision: 29541
2011-12-15 13:25:23 +00:00
0655552860
ar71xx: ag71xx: don't use port 4 of the switch, it is not connected on ar724x
...
SVN-Revision: 29540
2011-12-15 13:25:21 +00:00
204fc6bed5
ar71xx: ag71xx: nuke ar7240sw_init
...
SVN-Revision: 29539
2011-12-15 13:25:20 +00:00
d1f7783612
ar71xx: fix mac addresses on jjPlus devices
...
SVN-Revision: 29538
2011-12-15 13:25:18 +00:00
d3058b8f8c
ar71xx: build image for the Hornet-UB board
...
SVN-Revision: 29536
2011-12-14 20:54:11 +00:00
b9c5cb5c9a
ar71xx: add support for ALFA Network's Hornet-UB board
...
SVN-Revision: 29535
2011-12-14 20:54:10 +00:00
66c8cc0f6d
ar71xx: add GPIO function bit defines for AR933X
...
SVN-Revision: 29534
2011-12-14 20:54:07 +00:00
0c38d36488
ramips: add support for Omnima MiniEMBWiFi board
...
This patch adds support for the Omnima MiniEMBWiFi
Ralink RT3050F based board.
Based on a patch by Ivan Ignjatic <ivan at omnima.co.uk>
SVN-Revision: 29533
2011-12-14 20:51:26 +00:00
7076d74b21
ar71xx: fix gpio count for ar7241/ar7242
...
SVN-Revision: 29532
2011-12-14 20:47:24 +00:00
b878f4a927
ar71xx: register extra leds behind the wireless mac on wzr-hp-g450h
...
SVN-Revision: 29531
2011-12-14 20:21:42 +00:00
e3017bc05e
ath9k: add support for registering extra leds connected to the wmac gpio lines
...
SVN-Revision: 29530
2011-12-14 20:21:36 +00:00
d2717d3d47
ar71xx: get rid of squashfs-4k images
...
SVN-Revision: 29522
2011-12-13 20:41:24 +00:00
5afedc67e2
generic: disable 'small sector' erase in m25p80 driver
...
This fixes the issues with the jffs2 images on various boards. Using
JFFS2 on devices with 4KiB erase sectors is not safe:
http://lists.infradead.org/pipermail/linux-mtd/2011-June/036591.html
SVN-Revision: 29521
2011-12-13 20:41:22 +00:00
4a441570ca
kernel: move linux/ath9k_platform.h to generic files so that it can be reused from other targets
...
SVN-Revision: 29516
2011-12-13 15:14:59 +00:00
3806671fe5
ar71xx: fix wireless led on wzr-hp-g450h
...
SVN-Revision: 29515
2011-12-13 15:00:43 +00:00
2dd7dfb1c9
ar71xx: enable AR9341 support at setup.c
...
Patch-by: dyq <729650915@qq.com>
SVN-Revision: 29514
2011-12-13 14:59:43 +00:00
058998acdb
ar71xx: Build images for Netgear WNDRMAC and WNDRMACv2
...
The WNDRMAC is a WNDR3700v2 (64MB RAM, 16MB flash) in a white case. The
WNDRMACv2 is a WNDR3800 (128MB RAM, 16MB flash) in a WNDRMAC case.
The WNDRMAC case doesn't have "holes" or labels for the 2.4GHz LED or
switch ports 2-4. The stock firmware uses a single LED (in the 5GHz
position) to indicate the status of both radios, and a single LED (in the
switch port 1 position) to indicate the status of all LAN ports. The
"missing" LEDs are present on the board, and easily shine through the
case. Unlike the stock firmware, OpenWrt will use these "hidden" LEDs.
I've tested the WNDRMACv2 image. I don't have a v1 WNDRMAC, but assume
that this is sufficient to build a fully-functional image.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29513
2011-12-13 14:59:40 +00:00
48f9717371
ar71xx: add gpios and usb for wzr-hp-g450h
...
SVN-Revision: 29509
2011-12-13 13:33:44 +00:00
4ca2d86493
ar71xx: use RedBoot parser on PB44
...
SVN-Revision: 29501
2011-12-11 15:52:47 +00:00
934eef78ca
convert to gpiolib
...
Signed-off-by: karlp@tweak.net.au
SVN-Revision: 29486
2011-12-09 07:52:10 +00:00
6e69765559
ar71xx: fix WNDR3x00 factory image generation
...
Factory images for WNDR3700v2 and WNDR3800 should contain these model IDs
for the device: field in their DNI tags, not WNDR3700.
This regressed in r29434, which redid WNDR3x00 model detection. The sixth
parameter to Image/Build/Netgear is only used as the -B argument to
mkdniimg, which is used to set the device: field. In r29434, this was
erroneously changed to be WNDR3700 for all models. The tools to flash
factory images (U-Boot's TFTP server and the factory software's upgrade
utility) may refuse to honor images with incorrect device: fields in their
DNI tags.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29473
2011-12-07 06:55:50 +00:00
8eb8a6e1e7
ar71xx: fix WNDR3x00 model detection
...
Detect the model name for /tmp/sysinfo/model based on 10 bytes at offset
56 in the art (caldata) mtd partition.
r29434 redid WNDR3x00 model detection, attempting to distinguish between
WNDR3700v2 and WNDR3800 by checking MemTotal in /proc/meminfo. However, it
contained a bug: it put the awk inside a $(...), with the result that all
WNDR3700v2 and WNDR3800 models would be reported as WNDR3800. This patch
checks the model name stored in the art partition, as is done by U-Boot
shipping on the WNDR3800. It has the likely advantage of working with
future models based on the WNDR3700 board. It also will not mis-detect
units on which people install more memory.
I have tested this patch on WNDR3700 (v1), WNDR3700v2, and WNDR3800.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29472
2011-12-07 06:55:39 +00:00
43bd4c6ad1
ramips: fix mac addresses on the DIR-300/600 boards
...
SVN-Revision: 29471
2011-12-06 20:06:08 +00:00
e33bb9ec66
linux: update 3.1 to 3.1.4
...
SVN-Revision: 29470
2011-12-06 19:50:30 +00:00
6e2ae90f4a
linux: update 3.0 to 3.0.12
...
SVN-Revision: 29469
2011-12-06 19:50:25 +00:00
c6b2b98812
ar71xx: create firmware image for the TL-WR740N/ND v4 boards
...
Based on a patch by Cristian Deluxe <djcristiandeluxe@gmail.com>
SVN-Revision: 29468
2011-12-06 16:26:44 +00:00
fbfad4e9b4
ar71xx: use hw_id, hw_rev and flash_layout with mktplinkfw
...
SVN-Revision: 29467
2011-12-06 16:26:43 +00:00
d753e08c79
ar71xx: fix TL-MR3x20 profile names in image/Makefile
...
SVN-Revision: 29463
2011-12-06 13:53:21 +00:00
62d8009cdd
ar71xx: cleanup TP-Link profiles
...
SVN-Revision: 29461
2011-12-06 10:29:25 +00:00
f7a482d382
ar71xx: add TP-Link board detection
...
SVN-Revision: 29459
2011-12-05 21:11:01 +00:00
bdc2eca7de
ar71xx: use correct mac on the lan interface on several TP-LINK devices
...
SVN-Revision: 29458
2011-12-05 21:10:58 +00:00
0103069372
ar71xx: allow to pass negative offset values for ar71xx_init_mac
...
SVN-Revision: 29457
2011-12-05 21:10:55 +00:00
ada92aee62
ar71xx: don't register PCI controller on AR934x if PCIE_RC bit is not set
...
SVN-Revision: 29456
2011-12-05 18:21:15 +00:00
c6bcf8d1d8
ar71xx: verify hardware id of firmware images on TP-Link boards
...
SVN-Revision: 29455
2011-12-05 18:11:51 +00:00
5ef6ec4a31
ramips: set mac addresses for the NBG-419N
...
Based on a patch by Nerijus Baliunas <nerijus@users.sourceforge.net>
SVN-Revision: 29454
2011-12-05 17:27:07 +00:00
750d560767
ramips: set preinit interface mac on the hw550-3g board
...
Based on a patch by Daniel Golle <dgolle@allnet.de>
SVN-Revision: 29453
2011-12-05 17:27:06 +00:00
b5d7b359b2
ramips: use ramips_get_mac_* functions in the preinit script
...
SVN-Revision: 29452
2011-12-05 17:27:04 +00:00
4d5b940e66
ramips: move ramips_get_mac_* functions to lib/ramips.sh
...
SVN-Revision: 29451
2011-12-05 17:27:03 +00:00
cc853acb3a
ramips: add ramips_ prefix to get_mac_{binary,nvram} functions
...
SVN-Revision: 29450
2011-12-05 17:27:02 +00:00
b1137d48a4
ramips: fix network configuration setup
...
SVN-Revision: 29448
2011-12-05 16:54:48 +00:00
4dc9092f4b
ar71xx: reclaim some unused space on TP-Link boards
...
With the default OpenWrt configuration, this increases the size
of the rootfs_data partition by 384KB/128KB on the older/newer
TP-Link models.
SVN-Revision: 29447
2011-12-05 14:52:36 +00:00
3e7a6d182a
ar71xx: check squashfs signature in TP-Link mtd parser
...
SVN-Revision: 29446
2011-12-05 14:52:33 +00:00
feebf484ba
ar71xx: use the lzma-loader on TP-Link boards w/o lzma support
...
SVN-Revision: 29444
2011-12-05 14:52:28 +00:00
d42968351f
ar71xx: add lzma loader
...
SVN-Revision: 29443
2011-12-05 14:52:25 +00:00
1f809532de
ar71xx: add preliminary support for wzr-hp-g450h
...
SVN-Revision: 29441
2011-12-05 14:20:51 +00:00
d1f63f8538
ar71xx: move multi-m25p80 concat code from wzr-hp-ag300h mach code to dev-m25p80.c, other buffalo routers use it as well
...
SVN-Revision: 29440
2011-12-05 14:20:44 +00:00
4cc2b9bb06
ar71xx: rewrite WNDR3700/3800 handling
...
SVN-Revision: 29434
2011-12-05 13:03:54 +00:00
78699c2e51
add some missing wndr3800 base-files definitions
...
SVN-Revision: 29433
2011-12-05 12:56:21 +00:00
5177814ade
ar71xx: change user-space board detection
...
SVN-Revision: 29432
2011-12-05 12:56:20 +00:00
8a3a60fc64
ar71xx: allow WNDR3700 image creation to fail if kernel/rootfs too big
...
SVN-Revision: 29431
2011-12-05 12:47:53 +00:00
56c9b50006
ramips: fix argus board rootfs size
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29422
2011-12-04 15:24:57 +00:00
7cfa39f032
ar71xx: use the tp-link parser on the tp-link boards
...
Also remove static partition maps.
SVN-Revision: 29416
2011-12-03 18:13:31 +00:00
514b1167c9
ar71xx: add mtd partition parser for the TP-Link boards
...
SVN-Revision: 29415
2011-12-03 18:13:27 +00:00
fc7fb29bae
ar71xx: run the RedBoot parser only on the RedBoot based boards
...
SVN-Revision: 29414
2011-12-03 18:13:25 +00:00
9cc28d5aa0
ar71xx: run the MyLoader parser only on the WP543 board
...
SVN-Revision: 29413
2011-12-03 18:13:23 +00:00
67a0b9aada
ar71xx: run the wrt160nl parser only on the WRT160NL board
...
Also remove static mtd partition definitions.
SVN-Revision: 29412
2011-12-03 18:13:20 +00:00
c8acd6e013
ar71xx: allow to pass part_probe types to the m25p80 driver
...
SVN-Revision: 29411
2011-12-03 18:13:18 +00:00
20483faed0
ar71xx: create initramfs images for the newer TP-Link boards
...
SVN-Revision: 29410
2011-12-03 16:57:23 +00:00
9a2005e5e6
ar71xx: remove swconfig and wpad-mini from custom profiles
...
SVN-Revision: 29408
2011-12-03 16:33:41 +00:00
bc1d818610
ar71xx: add uboot-envtools to the default package list
...
SVN-Revision: 29407
2011-12-03 16:33:40 +00:00
a02a9c3f8b
ar71xx: reclaim unused space in WNDR3700/3800 images
...
Patch by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29406
2011-12-03 16:33:38 +00:00
ac82296c53
ar71xx: add a profile and build image for the OM2P board
...
[juhosg: the name of the final image has been changed to
'openwrt-ar71xx-generic-om2p-squashfs-factory.bin']
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
SVN-Revision: 29397
2011-12-01 22:49:05 +00:00
f188f1bad5
ar71xx: add support for Ubiquiti AirRouter
...
Signed-off-by: Gergely Barta <gergely.barta@printerfairkft.hu>
SVN-Revision: 29395
2011-12-01 22:49:02 +00:00
0612667c34
ar71xx: configure default led behavior for the OM2P
...
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
SVN-Revision: 29394
2011-12-01 22:48:59 +00:00
3fccc3b376
ramips: enable sysupgrade on the RT-N15 board
...
SVN-Revision: 29393
2011-12-01 22:48:58 +00:00
4b2d1c3ad3
ramips: wrap long line in platform upgrade script
...
SVN-Revision: 29392
2011-12-01 22:48:57 +00:00
d622263588
ramips: add profile for the Asus RT-N15
...
This uses previously submitted rtl8366 kernel packages.
[juhosg: The kmod-gpio-dev package has been removed from the package list.]
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29391
2011-12-01 22:48:55 +00:00
3a9e02fa41
ramips: setup default network configuration for RT-N15
...
Based on a patch by Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29390
2011-12-01 22:48:54 +00:00
fc61c107f0
ramips: rt288x: add swconfig and rtl8366{s,_smi} drivers to the default profile
...
It is needed by the RT-N15 board.
SVN-Revision: 29389
2011-12-01 22:48:53 +00:00
80221fcd2a
ramips: remove default network configuration, and generate that from uci-defaults
...
SVN-Revision: 29387
2011-12-01 22:48:51 +00:00
4f6c58adac
ramips: use /lib/functions/uci-defaults.sh
...
SVN-Revision: 29386
2011-12-01 22:48:48 +00:00
39348e387f
ar71xx: use /lib/functions/uci-defaults.sh
...
SVN-Revision: 29385
2011-12-01 22:48:47 +00:00
569d8de6d6
ramips: simplify uci-defaults/network script
...
SVN-Revision: 29383
2011-12-01 22:48:45 +00:00
66c9a351dd
ramips: setup mac and network interfaces from separate functions
...
SVN-Revision: 29382
2011-12-01 22:48:43 +00:00
62d18e9f9a
ramips: fix Asus RT-N15 board support
...
Fix Asus RT-N15 flash partitions and make an image.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29381
2011-12-01 22:48:42 +00:00
2dd79d55c7
ramips: Sparklan wcr-150gn board fixes
...
* Fix partition sizes.
* Add buttons and leds.
* Register usb.
* Remove unnecessary stuff from image Makefile
* Fix rt2x00 eeprom extract.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29380
2011-12-01 22:48:41 +00:00
7c678e7511
ramips: fix package name of kmod-input-gpio-buttons
...
Based on a patch from Omnima Limited.
SVN-Revision: 29379
2011-12-01 22:48:39 +00:00
2ed38b24a8
ramips: move kmod-rt2800-pci to DEFAULT_PACKAGES
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29378
2011-12-01 22:48:38 +00:00
295e04084c
ramips: setup bc2 mac addresses from the generic network script
...
SVN-Revision: 29377
2011-12-01 22:48:37 +00:00
02f95d4fb3
ramips: combine network setup for all boards in one file
...
Inspired by the patch from Roman Yeryomin. Thanks, Roman!
This removes unnecessary duplication and simplifies network setup for new
boards. It would be a one line change most likely.
[juhosg: setup lan and wan interfaces for unspecified rt3x0x based boards
in order to avoid regression]
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
SVN-Revision: 29376
2011-12-01 22:48:35 +00:00
88cb7ae104
omap24xx: bump to 3.1.3
...
SVN-Revision: 29349
2011-11-28 12:46:18 +00:00
bf7316424c
lantiq: bump to 3.1.3
...
SVN-Revision: 29348
2011-11-28 10:22:58 +00:00
5e83009a52
targets: fix CONFIG_USB_STORAGE_* inconsistency
...
* all options were switched from bool to tristate in 2.6.30
* add/change/move them to generic, disabled by default
* remove extinct CONFIG_USB_STORAGE_DPCM dropped in 2.6.29, merged with CONFIG_USB_STORAGE_SDDR09
* remove extinct CONFIG_USB_STORAGE_SIERRA option in 2.6
* cleanup ordering
SVN-Revision: 29337
2011-11-25 20:47:44 +00:00
f20797306a
ar71xx: modify phy mask of the WP543 board
...
This fixes ethernet on newer boards. Based on a patch from #9702 .
SVN-Revision: 29328
2011-11-24 20:09:43 +00:00
c20d7378e5
ar71xx: fix wndr3800 machine name
...
This fixes the machine name in /proc/cpuinfo and luci status page machine name.
Signed-off-by: Petri Rosenström <petri.rosenstrom@gmail.com>
SVN-Revision: 29326
2011-11-24 20:09:38 +00:00
600b6efc41
ar71xx: copy atheros initramfs images to the image directory
...
SVN-Revision: 29325
2011-11-24 20:09:35 +00:00
d97cf76790
ar71xx: specify mtd layout in command line for the DB120 board
...
SVN-Revision: 29324
2011-11-24 20:09:32 +00:00
9389593db9
lantiq: drop 009-MIPS-make-oprofile-use-cp0_perfcount_irq-if-it-is-se.patch
...
This patch is/was a duplicate of generic/patches-3.1/307-mips_oprofile_fix.patch
SVN-Revision: 29294
2011-11-23 12:22:15 +00:00
4982ca983c
lantiq: * fixes ath5k eeprom handling * fixes sx76x * adds sx76x to userland api * minor style cleanups
...
Signed-of-by: Andrej Vlašić <andrej.vlasic0@gmail.com>
SVN-Revision: 29292
2011-11-22 18:50:51 +00:00
718907b661
don't package gpioctl by default
...
SVN-Revision: 29288
2011-11-21 16:36:39 +00:00
c33f21ae95
target/uml: export atomic64_* functions on 32-bit x86
...
SVN-Revision: 29287
2011-11-21 14:28:33 +00:00
9990523a0f
ar71xx: set GE0 phy_mask for AR933x
...
SVN-Revision: 29274
2011-11-20 11:30:10 +00:00
b5739aabd9
fix D-Link DSL-2650U image generation
...
SVN-Revision: 29266
2011-11-19 21:34:51 +00:00
8bac0df4ae
linux: update 3.0 to 3.0.9
...
SVN-Revision: 29264
2011-11-19 18:39:12 +00:00
ae90aa4efd
build images for D-Link DSL-2650U ( #9003 )
...
SVN-Revision: 29238
2011-11-18 10:37:03 +00:00
0b86c2648a
omap24xx: Fix cbus nested IRQ acking
...
SVN-Revision: 29237
2011-11-17 22:31:27 +00:00
df2810831c
omap24xx: Fix initialization of software IRQ mask
...
SVN-Revision: 29236
2011-11-17 21:02:00 +00:00
3f92f7dd90
omap24xx: Update 3.1 config
...
SVN-Revision: 29234
2011-11-17 19:35:57 +00:00
4793be2df9
omap24xx: Some retu/tahvo IRQ fixes
...
SVN-Revision: 29233
2011-11-17 18:06:19 +00:00
630bafc5dd
omap24xx: Add basic kexec fixes.
...
SVN-Revision: 29232
2011-11-17 14:57:34 +00:00
06c986984e
omap24xx: Add workaround for omapfb locking bug.
...
SVN-Revision: 29201
2011-11-16 22:34:38 +00:00
0f03e17bd0
Revert r29193
...
SVN-Revision: 29195
2011-11-16 19:03:23 +00:00
93f02b1ba0
omap24xx: Set platform specific optimization flags
...
SVN-Revision: 29194
2011-11-16 19:02:12 +00:00
b058e97af4
n810: Add xmodmap to profile
...
SVN-Revision: 29193
2011-11-16 19:01:19 +00:00
8d66465b08
include bridge and 8021q modules by default
...
SVN-Revision: 29164
2011-11-15 22:24:22 +00:00
bbe96f13a6
lantiq: add runtime generation of /etc/config/network
...
SVN-Revision: 29161
2011-11-15 18:21:00 +00:00
79a4642b40
lantiq: fix falcon build breakage
...
dev-wifi-rt2x00 fails to build on falcon due to missing pci
SVN-Revision: 29129
2011-11-14 18:55:58 +00:00
f27548448b
ar71xx: fix USB LED on the DB120 board
...
SVN-Revision: 29126
2011-11-14 17:43:15 +00:00
6ebbb1329d
ar71xx: add a function for selecting output signal on a given GPIO pin
...
SVN-Revision: 29125
2011-11-14 17:43:14 +00:00
0c1d3617d7
ar71xx: fix GPIO function handling on AR934x
...
SVN-Revision: 29124
2011-11-14 17:43:13 +00:00
aa0c8c4885
ar71xx: add AR71XX_ prefix to GPIO_REG_* defines
...
SVN-Revision: 29123
2011-11-14 17:43:11 +00:00
62a7795afd
ar71xx: merge nand scan patch
...
SVN-Revision: 29122
2011-11-14 17:43:10 +00:00
12dae96097
ar71xx: fix a compiler warning
...
SVN-Revision: 29110
2011-11-14 13:07:47 +00:00
5ae0fd802c
ar71xx: fix GPIO count for AR934x
...
SVN-Revision: 29109
2011-11-14 13:07:45 +00:00
e52269364a
ar71xx: flush DDR writeback buffers for WMAC and PCIe on AR934X
...
SVN-Revision: 29108
2011-11-14 11:49:53 +00:00
3104d70552
ar71xx: use a dummy irq chip for WMAC and PCIe irq hadling
...
SVN-Revision: 29107
2011-11-14 11:49:51 +00:00
42e8ae09b5
ar71xx: add AR934X_RESET_REG_PCIE_WMAC_INT_STATUS defines
...
SVN-Revision: 29106
2011-11-14 11:49:49 +00:00
c15caea360
ar71xx: add an irq parameter for ar724x_pcibios_init
...
SVN-Revision: 29105
2011-11-14 11:49:47 +00:00
cf90b24bb9
ar71xx: remove hardwired interface parameters from mach-* files
...
SVN-Revision: 29103
2011-11-14 07:38:09 +00:00
defc79cb40
ar71xx: force hardwired interface parameters in ar71xx_add_device_eth
...
SVN-Revision: 29102
2011-11-14 07:38:07 +00:00
6f4bc1ce37
ar71xx: use if-else instead of conditional operators in ar71xx_add_device_eth
...
SVN-Revision: 29101
2011-11-14 07:38:05 +00:00
7f787707de
build images for Pirelli A226M ( #10409 )
...
SVN-Revision: 29045
2011-11-13 19:19:22 +00:00
5dc2098448
register uart0 on DWV-S0 boards ( #10409 )
...
SVN-Revision: 29044
2011-11-13 19:19:18 +00:00
56a96ba876
refresh 3.0 patches
...
SVN-Revision: 29043
2011-11-13 19:19:14 +00:00
54da5cf11f
refresh 2.6.39 patches
...
SVN-Revision: 29042
2011-11-13 19:19:10 +00:00
717a4391d7
rename 456-board_DWV-S0_ehci.patch to 456-board_DWV-S0_fixes.patch
...
SVN-Revision: 29041
2011-11-13 19:19:05 +00:00
c093c9df34
fix typo, load ip17xx switch module
...
SVN-Revision: 29039
2011-11-13 18:41:26 +00:00
368bbc510b
ar71xx: enable has_gbit flag on AR724{0,1}
...
SVN-Revision: 29026
2011-11-13 17:36:36 +00:00
15d7016c9f
ar71xx: fixup onboard PCIe chip registration on the DB120 board
...
SVN-Revision: 29022
2011-11-13 12:48:03 +00:00
f623066e60
ar71xx: drop DB120_WMAC_MAC_OFFSET, it is not needed
...
SVN-Revision: 29021
2011-11-13 12:48:01 +00:00
d2316b2a45
ar71xx: ag71xx: add support for getting switch port link status
...
SVN-Revision: 29017
2011-11-13 11:27:04 +00:00
d0db89133c
ar71xx: remove mii_ctrl resources of the ethernet devices
...
SVN-Revision: 29016
2011-11-13 11:27:03 +00:00
34015ed6e8
ar71xx: ag71xx: remove unused mii_ctrl field from struct ag71xx
...
SVN-Revision: 29015
2011-11-13 11:27:01 +00:00
2d882cff23
ar71xx: ag71xx: remove unused mii_cfg related functions and defines
...
SVN-Revision: 29014
2011-11-13 11:27:00 +00:00
538a9493b9
ar71xx: set MII interface speed from the set_speed callbacks
...
SVN-Revision: 29013
2011-11-13 11:26:59 +00:00
93cd46be13
ar71xx: rename set_pll callback to set_speed in ag71xx_platform_data
...
Also rename the corresponding callback functions.
SVN-Revision: 29012
2011-11-13 11:26:57 +00:00
9579bb4267
ar71xx: ag71xx: remove MII interface setup code
...
SVN-Revision: 29011
2011-11-13 11:26:56 +00:00
da64ce8603
ar71xx: configure MII interface type from ar71xx_setup_phy_if_mode
...
SVN-Revision: 29010
2011-11-13 11:26:54 +00:00
0112153a0e
ar71xx: fix occasional kernel hangs during boot on AR934x
...
The patch taken from the linux-mips mailing list.
The Kernel hangs occasionally during boot after
"Calibrating delay loop..". This is caused by the
c0_compare_int_usable() routine in cevt-r4k.c
returning false which causes the system to disable
the timer and hang later. The false return happens
because the routine is using a series of four calls
to irq_disable_hazard() as a delay while it waits
for the timer changes to propagate to the cp0 cause
register. On newer MIPS cores, like the 74K, the
series of irq_disable_hazard() calls turn into ehb
instructions and can take as little as a few clock
ticks for all 4 instructions. This is not enough of
a delay, so the routine thinks the timer is not
working.
This fix uses up to a max number of cycle counter
ticks for the delay and uses back_to_back_c0_hazard()
instead of irq_disable_hazard() to handle the hazard
condition between cp0 writes and cp0 reads.
SVN-Revision: 29009
2011-11-13 11:26:52 +00:00
1afc76ea13
ar71xx: refresh kernel patches
...
SVN-Revision: 29008
2011-11-13 11:26:51 +00:00
d8acb75009
linux: update 3.1 to 3.1.1
...
SVN-Revision: 29007
2011-11-13 10:48:05 +00:00
a8797d0de6
lantiq: add uci-defaults code for handling leds
...
SVN-Revision: 29004
2011-11-12 23:40:21 +00:00
832e02cd77
lantiq: add /lib/lantiq.sh and make hotplug handlers use it
...
SVN-Revision: 29003
2011-11-12 23:40:16 +00:00
5dcbbf0160
lantiq: rename leds
...
SVN-Revision: 29002
2011-11-12 23:40:12 +00:00
d84b7596d9
lantiq: split compat headers out of bsp header patch
...
SVN-Revision: 29001
2011-11-12 23:40:07 +00:00
2cff80f015
lantiq: adds hotplug handler for loading rt2x00 firmware
...
SVN-Revision: 29000
2011-11-12 23:40:01 +00:00
3660c51c40
lantiq: adds hotplug handler for handling buttons and makes w303v work with it
...
SVN-Revision: 28999
2011-11-12 23:39:56 +00:00
4248705108
lantiq: cleanup default package selection
...
SVN-Revision: 28998
2011-11-12 23:39:51 +00:00
eb20ab87e6
lantiq: w303v has its rt2860 eep on the nor flash. tell compat-wireless how to use it
...
SVN-Revision: 28994
2011-11-12 18:41:15 +00:00
bbfaaeffd6
kernel: ar8216: add support for the AR8236 switch
...
SVN-Revision: 28993
2011-11-12 14:09:52 +00:00
ecb3690d0a
kernel: ar8216: move port vlan setup into a separate function
...
SVN-Revision: 28992
2011-11-12 14:09:50 +00:00
5ad763075e
ar71xx: use the button for WPS control on the DB120
...
SVN-Revision: 28990
2011-11-12 12:50:20 +00:00
4555be2bec
ar71xx: register the second ethernet interface on the DB120 board
...
SVN-Revision: 28989
2011-11-12 12:50:19 +00:00
368c6605a0
ar71xx: implement SoC specific phy interface setup
...
SVN-Revision: 28988
2011-11-12 12:50:18 +00:00
21d317b9cc
ar71xx: move phy interface setup into a separate function
...
SVN-Revision: 28987
2011-11-12 12:50:16 +00:00
aff0c84ffa
ar71xx: register both MDIO bus on the DB120 board
...
SVN-Revision: 28986
2011-11-12 12:09:59 +00:00
b144249108
ar71xx: add AR934X specific MDIO registration code
...
SVN-Revision: 28985
2011-11-12 12:09:56 +00:00
Gabor Juhos
Hauke Mehrtens
Jonas Gorski
Jo-Philipp Wich
Florian Fainelli
John Crispin
Imre Kaloz
Felix Fietkau
Daniel Dickinson
Nicolas Thill
Michael Büsch