The PHY_SWAP and PHY_ADDR_SWAP bits are initialized
differently by different versions of the bootloader.
This leads to broken ethernet connection with OpenWrt
on some boards.
Turn both SWAP bits OFF on these boards to make it
consistent regardless of the bootloader used.
Based on a patch by Michel Stempin <michel.stempin@wanadoo.fr>.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35037
Summary:
* remove all files/* (since merged to upstream)
* patches on nand-spl, mmc and lcd driver
Thanks a lot to Xiangfu Liu!
Signed-off-by: Xiangfu Liu <xiangfu@sharism.cc>
SVN-Revision: 35034
The busybox size is increased by 3.2KByte uncompressed on bcm47xx with
this commit.
This zram-swap automatically creates a zram device, a swap partition on
it and make the kernel swap pages to it.
Thank you Bastian Bittorf <bittorf@bluebottle.com> for idea and the
script.
SVN-Revision: 35025
I wanted to use some statistics from /sys/kernel/debug/ieee80211,
so I enabled PACKAGE_MAC80211_DEBUGFS. But I could not use it,
because CONFIG_KERNEL_DEBUG_FS was not set and it's a little bit
hidden. After manually setting CONFIG_KERNEL_DEBUG_FS to y,
everything was fine. This patch automatically selects
CONFIG_KERNEL_DEBUG_FS if PACKAGE_MAC80211_DEBUGFS is set.
Additionally, the help text says "Say N unless you know you need this.",
but it's default y. This help text is copied verbatim from the
kernel's Kconfig and not true for us. So remove this part of the
help text
Signed-off-by: Stefan Hellermann <stefan@the2masters.de>
SVN-Revision: 35014
Allow bcm63xxpart to receive a caldata offset if calibration data is contained in flash.
Tested-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
SVN-Revision: 35010
This adds diag leds/buttons support for Linksys E1000 V1. It worked on
my router, however it may need some tweaking by people more familiar
with openwrt and c to make it fit for commiting.
Thank you hhm for this patch.
SVN-Revision: 34996
This Ethernet driver is in early development stage and still has some problems.
This was working on my bcm4716 based device.
Thanks to Rafał Miłecki <zajec5@gmail.com> for writing this driver.
SVN-Revision: 34995
I wrote this patch some time ago because I had a need for one of the
Gigabit ports (Linksys E3000) to be forced to 100FD. This is based
on the robocfg sources included w/ the RT-N16 sources from ASUS.
Since work is progressing on a BGMAC driver that could be included in
OpenWRT, this may be useful to someone else.
In testing, forcing the speed to 10/100 or 1000 worked fine; however,
when trying to force full-duplex mode, the result was always
half-duplex. I was not able to isolate the source of the problem
(this patch, driver or H/W limitation). The only way I could get it
to work was to set the port to Auto, but then only advertise 100FD
(not included in this patch).
I have a modified version of the robocfg package as well, I'd have to
clean it up a little first (remove the full-duplex hack) before
submitting it if there is interest.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34992
Adjust the IRQ Flag value from 8 to 7 for I2S Core for BCM4716 and
BCM4748 (per the Broadcom SDK). IRQ Flag values greater than 7 are
ignored when setting the interrupt masks.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 34990
Neither --create-backup nor --restore-backup need an image name (following
the backup filename). Treat them in uniform way.
Mostly fixes#12346.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 34974
Gabor Juhos
Mirko Vogt
Vasilis Tsiligiannis
Jo-Philipp Wich
Hauke Mehrtens
Felix Fietkau
John Crispin
Steven Barth
Jonas Gorski