8a4726bca8
imx6: remove sdma binary
...
SVN-Revision: 37682
2013-08-04 13:28:26 +00:00
2fcaba306e
brcm47xx: change board detection for some Asus devices
...
This closes #13316
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37680
2013-08-04 12:36:13 +00:00
cccc9e214b
kernel: do not build FW_LOADER as a module.
...
CONFIG_FW_LOADER=y is set in the generic config and our packages in
packages/kernel/linux are depending on it to be compiled into the
kernel.
This fixes some dependency problem where kmod-r8169 misses
firmware_class.ko.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37672
2013-08-04 09:41:10 +00:00
36cc8cc856
imx23: add missing DTS config for lradc
...
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 37663
2013-08-03 10:37:25 +00:00
370ad94576
imx23: add hw crypto (dcp) support
...
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 37662
2013-08-03 10:35:18 +00:00
b2d2ca4bbd
kernel: add missing config options
...
SVN-Revision: 37660
2013-08-02 20:13:54 +00:00
219eac1856
kernel: add missing config option
...
SVN-Revision: 37657
2013-08-02 16:51:47 +00:00
c47a55dd0d
kernel: add missing config option
...
brcm47xx does not use CONFIG_B53_SPI_DRIVER, but it could be selected if spi is build as a module
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37656
2013-08-02 16:16:23 +00:00
3e9ad14992
kernel: ocf: add missing kernel dependencies
...
OCF_CRYPTOSOFT uses both symbols form crypto_hash and crypto_blkcipher,
so let it select these through kernel config.
Fixes the following build error:
ERROR: "crypto_alloc_ahash" [crypto/ocf/cryptosoft.ko] undefined!
ERROR: "crypto_ahash_digest" [crypto/ocf/cryptosoft.ko] undefined!
ERROR: "crypto_ahash_setkey" [crypto/ocf/cryptosoft.ko] undefined!
make[6]: *** [__modpost] Error 1
make[5]: *** [modules] Error 2
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37652
2013-08-01 23:04:42 +00:00
290dade033
brcm47xx: switch to kernel 3.10.4
...
This uses a new switch driver.
The old ADMTEK Adm6996 switch is not supported any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37650
2013-08-01 21:01:59 +00:00
7e14fd55fd
brcm47xx: use lib phy when tg3 is in use
...
This is untested, but probably needed to make it work with the phy lib switch driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37649
2013-08-01 20:47:55 +00:00
8966b86067
kernel: b53: use devm_gpio_request_one() to request gpio
...
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37648
2013-08-01 20:46:56 +00:00
2b55968f5d
brcm47xx: improve detection of Linksys WRTSL54GS
...
This closes #13319
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37647
2013-08-01 19:33:59 +00:00
6d7f796b52
brcm47xx: remove support for kernel 3.9
...
This is not needed any more.
SVN-Revision: 37646
2013-08-01 19:17:51 +00:00
e1127aca07
kernel: b53: add support for GPIO reset
...
This is needed for some switches used on bcm47xx SoCs like the one on the Asus RT-N66U.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37645
2013-08-01 19:05:34 +00:00
2363cb3893
brcm47xx: add function to get a gpio pin by name
...
bcm47xx_nvram_gpio_pin() returns a gpio pin number for a given name based
on configuration data in nvram.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37644
2013-08-01 19:04:12 +00:00
169e184521
ramips: add Poray IP2202 support
...
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 37640
2013-08-01 14:31:15 +00:00
ce4228b417
ramips: add Poray X8 support
...
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 37639
2013-08-01 14:31:09 +00:00
54968110f1
ramips: add Poray X5/X6 Support
...
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 37638
2013-08-01 14:31:04 +00:00
0dc3b44b0d
ramips: add Poray M4 4M/8M support
...
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 37637
2013-08-01 14:30:58 +00:00
23d3b705df
ramips: add Poray M3 support
...
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 37636
2013-08-01 14:30:53 +00:00
aaedf6c8c6
ramips: add basics for Poray devices
...
This commit adds the basic elements to support Poray brand routers.
It contains a tool to do the encryption/obfuscation that is used in
Poray routers.
Support for Poray devices was worked on by:
Felix Kaechele <heffer@fedoraproject.org>
Luis Soltero <lsoltero@globalmarinenet.com>
Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 37635
2013-08-01 14:30:46 +00:00
b4c722267e
lantiq: fix VG3503J ethernet/gphy led support
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37634
2013-08-01 14:30:40 +00:00
046b282429
ralink: add mt7620a_mt7610e profile
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37633
2013-08-01 14:30:33 +00:00
9eb3572b7b
imx23: add lradc support
...
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 37632
2013-08-01 09:36:37 +00:00
91e8082e2d
kernel: add missing iio config symbols for 3.10
...
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 37631
2013-08-01 06:58:08 +00:00
e2b2e3886b
brcm47xx: run mtd fixtrx linux every time
...
With this patch it is possible to boot a device with kernel 3.10 a second time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37625
2013-07-31 17:41:52 +00:00
0a6e0228d9
imx23: add SoC sound support
...
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 37622
2013-07-31 09:52:46 +00:00
28d03a9983
kernel: update remaning platforms accidentally left out of r37617
...
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37619
2013-07-30 08:00:25 +00:00
8f04792531
kernel: update to linux 3.10.4, refresh patches
...
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37617
2013-07-29 22:42:22 +00:00
336c94c32d
lantiq: setup gphy leds on TPlink TDW8970
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37612
2013-07-29 13:10:42 +00:00
c3b5ee96b9
lantiq: add gphy pinmux definitions
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37611
2013-07-29 13:10:37 +00:00
61e6be686f
lantiq: set sane default for phy leds
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37610
2013-07-29 13:10:32 +00:00
c2600d13d1
ramips: fix indenting of spi partitions inside dts files
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37609
2013-07-29 13:10:26 +00:00
99e3616dac
kernel: add missing config symbols for 3.10
...
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37602
2013-07-29 12:48:57 +00:00
73c4d73d6d
build: unify target independent optimization options
...
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37600
2013-07-29 09:38:29 +00:00
cc26f768e4
kernel: stop patching -funit-at-a-time into CFLAGS, it has no effect on recent compilers
...
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37598
2013-07-29 09:38:21 +00:00
ad59c4e646
bcm53xx: compile b53 switch driver
...
SVN-Revision: 37587
2013-07-28 22:14:55 +00:00
1377916ea7
bcm53xx: update patches
...
This reorders the patchs and adds some new ones.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37586
2013-07-28 22:13:52 +00:00
333252e493
bcm53xx: use clocksource patch as it was committed upstream
...
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37585
2013-07-28 21:22:50 +00:00
3e8c39f239
bcm53xx: add initial bgmac patches
...
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37584
2013-07-28 21:20:15 +00:00
24628e4ce7
bcm53xx: activate pci and usb in kernel config
...
This is not working, just compiling
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37583
2013-07-28 21:10:42 +00:00
d6a23e1ae9
imx6: update default packages
...
SVN-Revision: 37582
2013-07-28 20:34:21 +00:00
a08eab3ce8
imx6: add support for EHCI USB
...
SVN-Revision: 37581
2013-07-28 20:34:19 +00:00
65584ed54f
ar71xx: add profile and build image for the WNR612 v2 board
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3876/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37577
2013-07-28 10:23:38 +00:00
41d136f2c8
ar71xx: add user-space support for the WNR612 v2 board
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3876/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37576
2013-07-28 10:23:37 +00:00
6d8163505e
ar71xx: add kernel support for the Netgear WNR612 v2 board
...
Netgear WNR612 v2:
- cpu Atheros AR7240 (Python) @400MHz
- flash 4MB
- ram 32MB
- ethernet 10/100: 1xwan + 2xlan (only two)
- radio AR9285
[juhosg: use a separate kernel patch]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3876/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37575
2013-07-28 10:23:36 +00:00
ede1587ed8
ar71xx: add profile and build image for the TL-WR710N board
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3873/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37574
2013-07-28 10:23:34 +00:00
5f5257e234
ar71xx: add user-space support for the TL-WR710N board
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3873/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37573
2013-07-28 10:23:33 +00:00
c5029c2ebf
ar71xx: add kernel support for the TP-LINK TL-WR710N v1 board
...
Small router sold in EU: AR9330@400MHz, 1x USB2.0,
2x ethernet, 8MB flash, 32MB ram, one led, one button.
See: http://galeria.tech-blog.pl/TP-Link_TL-WR710N-EU/
[juhosg: use a separate kernel patch]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3873/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37572
2013-07-28 10:23:32 +00:00
af1dd57a37
ar71xx: build image for the MERCURY MW4530R board
...
Mercury MW4530R is a TP-Link TL-WDR4310 clone but
with a much lower price tag (~ $40). This patch
is tested to work at trunk r37525.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3856/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37571
2013-07-28 10:23:31 +00:00
8b6f392b72
ar71xx: add model detection for the MERCURY MW4530R board
...
Mercury MW4530R is a TP-Link TL-WDR4310 clone but
with a much lower price tag (~ $40). This patch
is tested to work at trunk r37525.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3856/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37570
2013-07-28 10:23:29 +00:00
b49dc036e8
ar71xx: TEW632BRP has buttons 'active low', fix board config
...
Looks like trunk@37090 has changed the logic that determines
if router's button was pressed. This resulted in TEW632BRP
always booting into failsafe mode because it detected pressed
button (which was not pressed).
Measure with voltmeter has shown that buttons on this router
are actually active-low. This patch reflects this fact in
board configuration and fixes 'load info failsafe mode' issue.
Note: it looks like Trendnet TEW632BRP and a close relative
to TEW-652BRP V1.0 and D-Link DIR-615C1, so same problem may
exist on those routers as well. This patch doesn't affect
routers other than 632BRP and unfortunately I do not have
hardware to test this issue with other routers.
This patch fixes #13893 and is tested on actuall Trendnet
TEW632BRP.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37569
2013-07-28 10:23:22 +00:00
8dd30fa775
ramips: add MPR-A1 support
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37568
2013-07-27 09:23:52 +00:00
13b7ab81cf
ralink: gpio driver should not set gpio to input when irq is querired
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37567
2013-07-27 09:23:45 +00:00
eb089abd28
ramips: add back dwc_otg driver
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37566
2013-07-27 09:23:40 +00:00
718b47f0b4
ramips: MPR-A2 should use memory auto detection
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37565
2013-07-27 09:23:34 +00:00
115c6f85cf
ramips: enable usb phy support on rt5350
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37564
2013-07-27 09:23:29 +00:00
f4c4ca0b00
ralink: switch back to dwc_otg ... dwc2 seems to not work well with 3G modems
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37563
2013-07-27 09:23:24 +00:00
4176b6fdd3
strict_strtoul is obsolete, use kstrtoul instead
...
based on http://patchwork.openwrt.org/patch/3827/
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37562
2013-07-27 09:23:18 +00:00
c4413b6e08
ramips: unbreak asiarf dts files
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37561
2013-07-26 15:19:19 +00:00
f093cda481
ar71xx: add profile and fixup image generation for the TL-MR10U board
...
Create a separate board profile and update the profile
name in image/makefile. Also use the correct machtype
string in kernel command line.
Based on andelf's patch:
http://andelf.diandian.com/post/2013-05-22/40050677370
Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3840/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37550
2013-07-26 07:32:01 +00:00
f4d5ecdb9f
ar71xx: add user-space support for the TL-MR10U board
...
Based on andelf's patch:
http://andelf.diandian.com/post/2013-05-22/40050677370
Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3840/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37548
2013-07-26 07:31:59 +00:00
ec7fe3fab7
ar71xx: add kernel support for the TL-MR10U board
...
Based on andelf's patch:
http://andelf.diandian.com/post/2013-05-22/40050677370
[juhosg: extend WR703N code to handle the TL-MR10U
instead of adding a separate mach-tl-mr10u file]]
Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3840/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37547
2013-07-26 07:31:57 +00:00
e9688455f6
kernel: update 3.10 to 3.10.3
...
Also refresh 3.10 patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37546
2013-07-26 07:19:58 +00:00
bfe65eaf7a
lantiq: remove stale phy register setup properties from dts files
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37544
2013-07-25 20:54:51 +00:00
54b4074074
lantiq: add TP-Link TDW8970 image generation
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37543
2013-07-25 20:29:24 +00:00
a2c5540727
lantiq: add profile for TP-Link TDW8970
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37542
2013-07-25 20:29:20 +00:00
a99042c6a4
lantiq: add devicetree for TP-Link TDW8970
...
Signed-of-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37541
2013-07-25 20:29:15 +00:00
313636c1e4
lantiq: fix initramfs image generation for lzmaloader based images
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37540
2013-07-25 20:29:10 +00:00
a4d31c0353
lantiq: make macs loadable from mtd partitions
...
This is a really ugly hack but it will have to do until we copy the ramips patches to the lantiq tree
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37539
2013-07-25 20:29:05 +00:00
32f7ae4ce6
lantiq: add a hook to make leds work on the secondary usb bus
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37538
2013-07-25 20:29:01 +00:00
4036be4408
lantiq: update pcie driver
...
This is an intermediate commit until the new OF driver is functional.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37537
2013-07-25 20:28:56 +00:00
dee22d069f
xburst: Add missing kernel config symbol
...
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
SVN-Revision: 37534
2013-07-25 18:39:34 +00:00
04aaf7a03e
ramips: disable hg255d
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37532
2013-07-25 17:03:08 +00:00
7feebeb193
ramipe: disable HG255D support
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37531
2013-07-25 16:55:48 +00:00
9b2c7be0c4
ramips: important patch for HG255D
...
r37505 add support for Huawei HG255D, but it only tested under a community hacked u-boot ("lintel u-boot"), which has a different mtd layout compared to origin one. If you install it on a box with origin u-boot, the origin factory part will be destroyed, and your wifi interface will never up!!!
This patch shrink firmware part in mtd layout to exclude origin factory part, and I will prepare another patch to fix the eeprom extract issue for box with origin u-boot.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
SVN-Revision: 37530
2013-07-25 16:01:58 +00:00
3ad136d9e3
ramips: Basic support for the AsiaRF RT5350 based AWM002 module and evaluation board.
...
Basic support for the AsiaRF RT5350 based AWM002 module and evaluation board.
http://www.asiarf.com/Smallest-Tiny-Ralink-802-11n-Wireless-AP-Router-Module-Board-AWM002-product-view-375.html
Signed-off-by Jon Smirl <jonsmirl@gmail.com>
SVN-Revision: 37521
2013-07-24 08:54:41 +00:00
3f3cac6136
ramips: fix HG255D VLAN initial detect issue
...
Signed-off-by: Leon Xu <ylxu72@gmail.com>
SVN-Revision: 37517
2013-07-23 13:07:00 +00:00
9181c569c4
linux/atheros: add 3.10 kernel support
...
SVN-Revision: 37513
2013-07-22 19:10:59 +00:00
db32da6b16
xburst: Unmark broken
...
3.10 support is working fine for this platform, so unmark it broken.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
SVN-Revision: 37512
2013-07-22 18:44:05 +00:00
44745f714e
xburst: Remove 3.8 support
...
3.8 support for this platform is broken, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
SVN-Revision: 37511
2013-07-22 18:42:36 +00:00
32a83db347
xburst: Add 3.10 support
...
Missing files from the previous commit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
SVN-Revision: 37510
2013-07-22 18:41:23 +00:00
e7d77883c7
xburst: Add 3.10 support
...
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
SVN-Revision: 37509
2013-07-22 18:40:32 +00:00
ea55883a51
ar71xx: fix switch port map for the Archer C7
...
The correct port number for the WAN port is 1.
Update the VLAN port maps to reflect that.
https://forum.openwrt.org/viewtopic.php?pid=203755#p203755
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37507
2013-07-22 16:02:13 +00:00
bc91bec9f6
kernel/3.10: rework MIPS FPU emulation disable patch
...
Get rid of some ifdefs, and make sure that the microMIPS
specific code is disabled as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37506
2013-07-22 16:02:12 +00:00
0cc1e2acb4
ramips: Add support for Huawei HG255D in trunk
...
HG255D is a kind of popular low-end home gateway in China, this patch bring the the trunk support for it. It is adapted from a local Chinese community (www.right.com.cn), so credit should given to them.
This patch is tested to work except trivial LED issues.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
SVN-Revision: 37505
2013-07-22 15:36:39 +00:00
ef944dcb85
kernel: update 3.10 to 3.10.2
...
Also refresh 3.10 patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37502
2013-07-22 15:31:13 +00:00
6a5b4ec7dc
kernel: update 3.9 to 3.9.11
...
Also refresh 3.9 patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37501
2013-07-22 15:30:56 +00:00
8d0cd50f30
ralink: set remove dwc_otg from default packages and use dwc2 instead
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37499
2013-07-22 13:52:52 +00:00
ffe389c4c5
ralink: remove dwc_otg from modules.mk
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37498
2013-07-22 13:52:44 +00:00
5525b2136e
ralink: set v3.10 as default
...
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37497
2013-07-22 13:52:32 +00:00
a50c18c632
kernel: fix crash in act_connmark in 3.9 and 3.10 ( fixes #13916 , #13876 )
...
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37493
2013-07-21 13:53:54 +00:00
a1ec175d7b
kernel: add missing config option CONFIG_SND_MXS_SOC
...
This is needed by imx23 target.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37492
2013-07-21 12:27:22 +00:00
94439c2b5d
kernel: add a new global config symbol for enabling rfkill support (can be enabled by default via target feature flag)
...
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37491
2013-07-21 11:55:30 +00:00
8fc44d1f5f
kernel: Remove gpio-pwm patches
...
There is no platform using the gpio-pwm driver, yet these patches break the
generic PWM framework that is in upstream. So just remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
SVN-Revision: 37490
2013-07-21 11:43:16 +00:00
bb141e06a2
kernel: merge a proposed fix from LKML for fixing infinite data returned by /proc/timer_list
...
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37484
2013-07-20 18:35:54 +00:00
7ef37c8e3e
brcm63xx: add linux 3.10 support
...
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37481
2013-07-20 11:30:26 +00:00
205f7248ae
Revert "ar71xx: override cpu_has_mmips feature"
...
This reverts r37477. A generic patch is used to fix
this globally, so revert the ar71xx specific change.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37480
2013-07-20 10:14:08 +00:00
a2d12049e0
kernel/3.10: add a generic patch for cpu_has_mmips override
...
Backport of commit 3ddc14add5e6341cf8ef4058c34c67ba7fd15317
from 3.11-rc1
Suggested-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37479
2013-07-20 10:14:05 +00:00
Luka Perkov
Hauke Mehrtens
Zoltan Herpai
Jonas Gorski
John Crispin
Felix Fietkau
Gabor Juhos
Lars-Peter Clausen