Commit Graph

40 Commits (a787a028739718548e357bfca3de0013c3525bfd)

Author SHA1 Message Date
Hauke Mehrtens d7ebbd0ac7 brcm47xx: use "firmware" partition name
Some time ago, after switching to the mainline bcm47xxpart driver
following patch has been applied:

commit 03cef8725d2062335ffc3de50fc037b294fd458c
Author: hauke <hauke@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date:   Sat Apr 6 22:22:26 2013 +0000

    brcm47xx: use old partition names again for kernel 3.8

    This fixes sysupgrade. The partition names are used all over the Internet in various howtos.

    Thank you russell for spotting this problem.

I propose to revert this change and make sysupgrade use "firmware"
instead. This makes brcm47xx compatible with widely used ar71xx and
after all "firmware" sounds like a much better name for... the firmware.

This change doesn't affect "sysupgrade" usage, because it never takes a
partition name as a parameter. This change only affects users using mtd
tool directly. Hopefully there are not many howtos using "mtd" command.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 38973
2013-12-01 16:32:32 +00:00
Hauke Mehrtens 32cbc948a1 brcm47xx: fix netconfig for inverted vlan?ports in nvram
This was observed on the Belkin Share F7D7302.

SVN-Revision: 38769
2013-11-11 23:04:47 +00:00
Hauke Mehrtens 97b15fc45b brcm47xx: add support for ipv6 in default network config
Modify /etc/init.d/netconfig to use UCI defaults for building the
default network config, which includes appropriate defaults for IPV6.

Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>

SVN-Revision: 38294
2013-10-02 23:22:18 +00:00
Hauke Mehrtens e2b2e3886b brcm47xx: run mtd fixtrx linux every time
With this patch it is possible to boot a device with kernel 3.10 a second time.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 37625
2013-07-31 17:41:52 +00:00
Hauke Mehrtens f8d55e7541 brcm47xx: use b53 phy driver for the switch in kernel 3.10
This makes it possible to use swconfig to controll the switch.

This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.

SVN-Revision: 37304
2013-07-14 14:11:17 +00:00
Hauke Mehrtens 3bc90a4d23 brcm47xx: fix switch handling
This fixes some problems with the switch handling

 * It now send the messages again to indicate a button for failsafe mode should be pressed
 * it does not leak packages between wan and lan any more
 * the switch works again in normal mode

The Ethernet connection has to be up when the switch driver switch-robo
is insmoded therefor we just do it again.
Explicitly set enable_vlan to prevent leaking packages.

This should close #13869, #13868 and #13716

SVN-Revision: 37286
2013-07-14 13:19:58 +00:00
Hauke Mehrtens ef0b9be95e brcm47xx: do not load the kernel modules needed for Ethernet manually
add the boot flag to make the kernel modules needed for Ethernet and
diag load on startup.

SVN-Revision: 37284
2013-07-14 12:59:00 +00:00
Hauke Mehrtens e800436de3 brcm47xx: do not change nvram without user interaction
SVN-Revision: 37281
2013-07-14 12:56:42 +00:00
Hauke Mehrtens e041d370a7 brcm47xx: proc gets mounted without this patch
SVN-Revision: 37272
2013-07-13 21:42:19 +00:00
Hauke Mehrtens 8dabd7a26b brcm47xx: remove obsolete hotplug stuff
SVN-Revision: 37271
2013-07-13 20:38:33 +00:00
John Crispin 39df8d1a45 brcm47xx: dont manually insmod switch drivers
Signed-off-by: John Crispin <bloic@openwrt.org>

SVN-Revision: 36993
2013-06-21 16:53:15 +00:00
Hauke Mehrtens 4a46687d25 brcm47xx: use old partition names again for kernel 3.8
This fixes sysupgrade. The partition names are used all over the Internet in various howtos.

Thank you russell for spotting this problem.

SVN-Revision: 36235
2013-04-06 22:22:26 +00:00
Hauke Mehrtens 694050a4cf brcm47xx: netconfig: add bacis support for swconfig
Parse the cpu port from swconfig and explicitly mark the cpu port as tagged.

SVN-Revision: 35911
2013-03-09 19:24:43 +00:00
Hauke Mehrtens 9afdb046d3 brcm47xx: do not use vlan0 any more.
The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.

This makes OpenWrt always use vlan1 and vlan2 instead.

SVN-Revision: 35704
2013-02-20 15:31:43 +00:00
Hauke Mehrtens 1a8218d6e4 brcm47xx: add initial support for kernel 3.8
This contains the following new bigger changes:
 * new partition parser which still could lake some features or have bugs
 * new nand flash driver
 * using physmap-flash flash driver for parallel flash
 * some changes to the serial flash driver

With these changes OpenWrt starts using more of the mainline flash drivers.

SVN-Revision: 35632
2013-02-16 20:28:24 +00:00
Hauke Mehrtens 9de704a03b brcm47xx: improve cpuport detection for filesafe
Do not try to load bcm57xx.ko any more this is not needed for kernel 2.6 and 3.X
Ask the switch driver where the CPU port is.

SVN-Revision: 35624
2013-02-16 16:24:15 +00:00
Hauke Mehrtens 92d16f38d7 brcm47xx: fix network config on simpleshare
The included patch will generate a correct network configuration on the simpletech simpleshare.

Thank you for the patch Will Holmes (RealOpty)

This closes #12361.

SVN-Revision: 35623
2013-02-16 15:24:48 +00:00
Hauke Mehrtens d9580d224a brcm47xx: try to automatically detect if the wan port is at port 4 and not at port 0.
This should fix #13000.

SVN-Revision: 35617
2013-02-16 12:37:24 +00:00
Hauke Mehrtens c0f6c75cf7 brcm47xx: if the cpuport of the switch is port 8 assume vlan0ports: "1 2 3 4 8" and vlan0ports: "0 8"
SVN-Revision: 35597
2013-02-14 12:38:16 +00:00
Hauke Mehrtens 54ca3eed5d brcm47xx: configure vlan correctly on some recent devices.
SVN-Revision: 35587
2013-02-13 16:05:52 +00:00
Hauke Mehrtens a1e3c0ca46 Add Failsafe support for Linksys E3000V1 / WRT610NV2
Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2
in /lib/preinit/05_init_interfaces_brcm.  The list of devices will need to
be expanded.  Is there a way to determine the correct cpu_port to use in a
generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if
"/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists?  Could
a similar method be used in "/etc/init.d/netconfig"?

Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>

SVN-Revision: 35491
2013-02-04 22:40:57 +00:00
Hauke Mehrtens c2198aba32 brcm47xx: Fix switch config on 4716/53115 devices
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>

SVN-Revision: 35490
2013-02-04 22:38:37 +00:00
Hauke Mehrtens 68aeb7af8e brcm47xx: load pps_core and ptp before tg3 to make the interface available for failsafe.
SVN-Revision: 35341
2013-01-27 21:48:28 +00:00
Hauke Mehrtens 4443997fd8 brcm47xx: add bgmac driver
This Ethernet driver is in early development stage and still has some problems.
This was working on my bcm4716 based device.

Thanks to Rafał Miłecki <zajec5@gmail.com> for writing this driver.

SVN-Revision: 34995
2013-01-03 02:05:22 +00:00
Hauke Mehrtens 8f6bdcffa1 brcm47xx: build b44 as a module
SVN-Revision: 34994
2013-01-03 02:00:25 +00:00
Hauke Mehrtens 22d62d311a brcm47xx: run ifup before starting the switch
In addition check_module is not needed, nobody checks the return value.

SVN-Revision: 34993
2013-01-03 01:59:43 +00:00
Mirko Vogt e34a4e0c7b Do not use deprecated path to functions.sh (/etc/functions.sh -> /lib/functions.sh)
SVN-Revision: 34793
2012-12-19 16:07:50 +00:00
Mirko Vogt 439a869090 Do not overload mount-call - trying to reduce confusion
The behaviour of calling 'mount' differed depending on whether it called
the busybox-mount, the mount of util-linux, the mount defined in
/lib/functions.sh and /lib/functions/boot.sh

/etc/preinit even included /lib/functions.sh and /lib/functions/boot.sh,
both re-defining 'mount'.

SVN-Revision: 34792
2012-12-19 16:07:46 +00:00
Hauke Mehrtens 4901ac8225 brcm47xx: improve suppressing printing if a module was found in preinit function.
Thank you Bastian Bittorf

SVN-Revision: 34680
2012-12-14 22:45:12 +00:00
Hauke Mehrtens 6c8efbfdc0 brcm47xx: Additional BCM4716 support
Additional BCM4716 support.  Still needs working ethernet driver.

Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>

SVN-Revision: 34672
2012-12-13 18:57:38 +00:00
Hauke Mehrtens 235c065e12 brcm47xx: suppress printing if a module was found in preinit function.
SVN-Revision: 34653
2012-12-13 00:11:11 +00:00
Hauke Mehrtens 3a4a6cfd64 kernel: in kernel 3.6.8 and later tg3 depends on hwmon.ko
SVN-Revision: 34652
2012-12-13 00:09:55 +00:00
Hauke Mehrtens aa8e887a46 brcm47xx: whitespace cleanups
SVN-Revision: 34329
2012-11-25 14:03:51 +00:00
Hauke Mehrtens 0818180715 activate failsafe on all ports of the switch and not just port 0.
Sometimes the port 0 was the WAN port or there could be some device
where the port 0 is not wired to an actual Ethernet port. Now telnet in
failsafe will listen on all ports of the switch so user do not have to
search for the correct port any more. This change will make the switch
leak traffic between the WAN and the LAN port, but you should not use
failsafe while connected to a untrusted network.

SVN-Revision: 33544
2012-09-25 14:04:59 +00:00
Florian Fainelli 3802769ea1 add vlan definitions for Siemens SE505v2
Hi,

this patch adds the correct vlan definitions for the Siemens SE505v2. It
applies to trunk as well as backfire (please apply here too). On
backfire this also patches brcm-2,4, because brcm47xx base-files is just
symlinked to brcm-2.4.

It also fixes two whitespace issues.

Tested with brcm47xx on both trunk and backfire branch and works as
expected.

Signed-off-by: Manuel Munz <freifunk@somakoma.de>

SVN-Revision: 28336
2011-09-30 12:55:33 +00:00
Jo-Philipp Wich ebb152295b fix the default network configuration for the ASUS WL-330gE (#8751)
SVN-Revision: 28024
2011-08-17 03:16:59 +00:00
Daniel Dickinson 17ba48cd90 target (base-files): Fixed failsafe mode by adding back insmod diag
SVN-Revision: 22186
2010-07-15 02:46:03 +00:00
Felix Fietkau 812f026323 add back the base-files/image code from brcm-2.4 to brcm47xx
SVN-Revision: 21945
2010-06-26 20:41:49 +00:00
Felix Fietkau 519b6a2f4c remove brcm47xx symlinks to brcm-2.4 (unfortunately svn does not allow a proper type changing commit)
SVN-Revision: 21944
2010-06-26 20:41:40 +00:00
Felix Fietkau 56231056ea strip the kernel version suffix from target directories, except for brcm-2.4 (the -2.4 will be included in the board name here). CONFIG_LINUX_<ver>_<board> becomes CONFIG_TARGET_<board>, same for profiles.
SVN-Revision: 8653
2007-09-06 16:27:37 +00:00