Commit Graph

26140 Commits (a787a028739718548e357bfca3de0013c3525bfd)

Author SHA1 Message Date
Felix Fietkau a787a02873 ar71xx: add missing tx gain table flag for buffalo wzr-hp-g450h
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39139
2013-12-19 17:18:12 +00:00
Felix Fietkau bac83378e7 ath9k: merge another round of upstream (or -pending) fixes and cleanups
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39138
2013-12-19 17:18:07 +00:00
Luka Perkov 5db5354c70 imx6: refresh patches
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 39135
2013-12-19 02:03:26 +00:00
Luka Perkov 7632535589 kernel: backport upstream inet fix
Without it in some occasions oops is shown on network restart. Problem was
noticed on imx6 targed.

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 39134
2013-12-19 02:03:25 +00:00
Luka Perkov 1e9161528b imx6: proper fix for io-remap
The previous patch was not the proper fix for PCI devices that require io
resources.  The new patch is the proper fix backported from mainline.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 39133
2013-12-19 02:03:16 +00:00
Jo-Philipp Wich de5d9827ef procd: fix service file tracking
The instance_config_move() function in the procd instance managing code is
missing a blobmsg_list_move() call to update the tracked file items with the
newly calculated checksums in case of a file change.

Without that change, services are always reloaded after the first change to
a tracked file regardless of whether there are any subsequent changes or not.

Add a missing instance of blobmsg_list_free() as well.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 39132
2013-12-18 15:38:28 +00:00
Jo-Philipp Wich 1789744958 netifd: add reload trigger for /etc/config/wireless as well
SVN-Revision: 39131
2013-12-18 12:38:29 +00:00
Gabor Juhos 2318a46d84 ar71xx: enable images for WD My Net N750
Now that the switch works correctly we can enable the images for this
board.

Flashing from the factory firmware, the factory failsafe loader and
sysupgrade was tested successfully.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4617/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39130
2013-12-17 22:14:13 +00:00
Gabor Juhos 1ebf211340 ar71xx: fix WD My Net N750 switch led cfg
Now that the switch is working correctly I had the chance to actually
test the LED config.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4616/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39129
2013-12-17 22:14:12 +00:00
Gabor Juhos c72313fd98 ar71xx: implement switch fix for WD My Net N750
The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.

This fix implements just that.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39128
2013-12-17 22:14:11 +00:00
Gabor Juhos 8b712436f3 ar71xx: implement callback in mdio reset
This enables us to add fixups to the board specific code for boards that
require special treatment of PHYs on mdio bus reset.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
http://patchwork.openwrt.org/patch/4614/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39127
2013-12-17 22:14:10 +00:00
Gabor Juhos ba860e4c3a ar71xx: make ag71xx_mdio_platform_data visible
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39126
2013-12-17 22:14:07 +00:00
Felix Fietkau d2329f88f3 busybox: add back support for top-level menuconfig based config overrides (can be used by custom packages to alter the config)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39125
2013-12-17 20:37:27 +00:00
Jonas Gorski 5c2aee90ac gpio-button-hotplug: fix crash on remove
Don't call gpio_keys_remove recursively. Setting the platform
data to NULL triggered an oops on the second iteration, so there was
no infinate loop.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 39124
2013-12-17 19:05:03 +00:00
Jo-Philipp Wich 7a24db90aa busybox: restore init scripts
Since the removal of the busybox menuconfig entries, the init scripts
for cron, telnet and ntp are not packaged anymore. Unconditionally
ship them from now on.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 39123
2013-12-17 17:17:00 +00:00
Jo-Philipp Wich de5ebc19c0 firewall: fix handling of tcp_ecn parameter
The firewall3 implementation as well as the shell implementation predating it
used to process the tcp_ecnoption as boolean while it actually is an integer.

Change the code to parse tcp_ecn as integer.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 39122
2013-12-17 16:59:47 +00:00
Gabor Juhos 31de995025 ar71xx: ag71xx: compute the RX buffer size from the maximum frame size
Currently, the AG71XX_RX_PKT_SIZE value limits the received
frame size to 1514/1516 bytes with/without a VLAN header
respectively. However the hardware limit is controlled by
the value the AG71XX_REG_MAC_MFL register which contains
the value of the max_frame_len field.

Compute the RX buffer size from the max_frame_len field
to get rid of the 1514/1516 byte limitation. Also remove
the unused AG71XX_RX_PKT_SIZE definition.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39121
2013-12-17 16:27:46 +00:00
Gabor Juhos b35e0da0f4 ar71xx: ag71xx: store RX buffer size in the ag71xx struct
This allows to change the value dynamically.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39120
2013-12-17 16:27:44 +00:00
Felix Fietkau 088eea282d iproute2: reduce .ipk package size from ~100k down to ~60k
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39119
2013-12-17 15:59:29 +00:00
Felix Fietkau 80b2fbc687 busybox: disable module utils, kmodloader provides them
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39118
2013-12-17 15:59:25 +00:00
Gabor Juhos 6072e777e9 ar71xx: ag71xx: store maximum frame length in the ag71xx struct
This will allow to use different values for the
different SoCs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39117
2013-12-17 15:18:16 +00:00
Gabor Juhos ea89cc9250 ar71xx: ag71xx: use mdio bus name in ar7240_probe messages
The ar7240_probe function uses the network device name
in the kernel log messages, however the name is not yet
initialized when the ar7240_probe function is called.
Use the mdio bus name in the messages to avoid ugly
log lines like the following one:

  eth%d: Found an AR7240/AR9330 built-in switch

Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39116
2013-12-17 15:12:52 +00:00
Gabor Juhos 0d7a6748e1 ag71xx: ag71xx: use device name for debugfs entry
The ag71xx debugfs code uses the network device name
for the device specific debugfs directory. Since r38689
'ar71xx: ag71xx: fix a race involving netdev registration'
the debugfs initialization happens before the ethernet
device gets registered and the network device name contains
'eth%d' at this point. If the board setup code registers
multiple ag71xx devices, the debugfs code tries to create
the device specific dir with the same name which causes
an error like this:

  eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
  ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
  ag71xx: probe of ag71xx.0 failed with error -12

Use the device name for the debugfs directory to avoid the
collisions. Also add an error message and change the return
code if the debugfs_create_dir call fails.

Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39115
2013-12-17 15:12:50 +00:00
Felix Fietkau 34839b95cf busybox: fix typo in Config.in (#14628)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39114
2013-12-17 07:17:00 +00:00
Luka Perkov b27f84034b imx6: ventana: add canbus utils
Some of the Gateworks Ventana boards have CAN bus support, therefore
we will install the userspace utils.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 39113
2013-12-17 02:47:20 +00:00
Luka Perkov 7802f4619b imx6: ventana: add default kernel modules for GSC
All Gateworks Ventana boards have a Gateworks System Controller
which emulates the following:
 - ds1672 RTC
 - pca953x GPIO expander
 - hardware monitor
 - at24 eeprom

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 39112
2013-12-17 02:47:18 +00:00
Luka Perkov 325a4f5b6e imx6: add rtc feature support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 39111
2013-12-17 02:47:17 +00:00
Luka Perkov a9376b6fdb kernel: add rtc-ds1672 module support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>

SVN-Revision: 39110
2013-12-17 02:47:16 +00:00
Luka Perkov ccf1ee93d9 imx6: drop upstreamed patch
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 39109
2013-12-17 02:47:15 +00:00
Luka Perkov 0b4e8c4c36 automake: update to 1.11.6
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 39108
2013-12-17 02:47:13 +00:00
Felix Fietkau 7340bc73f2 busybox: add support for config overrides via env/busybox-config
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39107
2013-12-16 19:27:35 +00:00
Felix Fietkau 405b5c2b92 busybox: remove busybox menuconfig from top level menuconfig
This will help with avoiding bogus bug reports caused by stale configs
and bad cases of user tinkering :)

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39106
2013-12-16 19:09:57 +00:00
Felix Fietkau cc304329b3 uClibc: disable sha256 and sha512 for libcrypt - saves about 13k uncompressed in libcrypt
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39105
2013-12-16 18:49:10 +00:00
Felix Fietkau b6bcb7ff2d hostapd: move old wifi setup scripts to hostapd-common-old
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39103
2013-12-16 18:42:43 +00:00
Gabor Juhos 5237a50089 ar71xx: add initial support for the Mikrotik RB911G/RB912UAG boards
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39102
2013-12-16 18:08:51 +00:00
Jo-Philipp Wich eda27e8382 dnsmasq: switch to /lib/functions/network.sh
This commit changes the dnsmasq init script to use the interface
status exposed by netifd. The old references to scan_interfaces()
and (indirect) accesses to uci state variables are removed and
replaced with corresponding network_*() calls.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 39101
2013-12-16 16:47:41 +00:00
Jo-Philipp Wich ef0ce72b39 base-files: ipcalc.sh: support bit length as netmask parameter
SVN-Revision: 39100
2013-12-16 16:29:23 +00:00
Jo-Philipp Wich fe230cac18 base-files: add network_get_protocol() to /lib/functions/network.sh
SVN-Revision: 39099
2013-12-16 16:28:45 +00:00
Felix Fietkau 5d79ad06c1 mac80211: fix AP mode scanning issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39098
2013-12-16 15:45:57 +00:00
Gabor Juhos 8461ffccc1 ar71xx: add NAND driver for the Mikrotik RB91x boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39097
2013-12-16 12:57:24 +00:00
Gabor Juhos d7a0184446 ar71xx: rb2011: use board name from the hardware config
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39096
2013-12-16 12:41:48 +00:00
Gabor Juhos 26ca95fefa ar71xx: rb2011: simplify setup code
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39095
2013-12-16 10:28:42 +00:00
Gabor Juhos 59b6cf1e70 ar71xx: rb2011: use the new RouterBOOT helpers
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39094
2013-12-16 10:28:41 +00:00
John Crispin 6218da5a41 ralink: fix dir810 networking
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 39093
2013-12-16 10:16:33 +00:00
Gabor Juhos 627651dfca ar71xx: rb95x: use the rb_get_wlan_data helper
Also remove unused RB_* defines.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39092
2013-12-16 10:11:02 +00:00
Gabor Juhos 16565ec94b ar71xx: add some RouterBOOT specific helper functions
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39091
2013-12-16 10:11:01 +00:00
Gabor Juhos 0601b5f404 kernel: define RB_ID_HW_OPTIONS in include/linux/routerboot.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39090
2013-12-16 10:11:00 +00:00
Gabor Juhos c92a4a427e ar71xx: refresh m25p80 patches
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39089
2013-12-16 10:10:58 +00:00
Felix Fietkau 12c05542e8 netifd: update to latest version, fixes a null pointer crash
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 39088
2013-12-16 10:08:13 +00:00
Gabor Juhos 728c2c6cff ar71xx: rb95x: nuke rb95x_gpio_init
Set up the chipselect GPIO directly in rb95x_nand_init
instead.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39087
2013-12-16 08:17:40 +00:00