Boot tested: http://pastebin.com/L6aAb9xj
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo:
update to 4.1 final
add patches added since submission
delete patches applied in later rcs
restore commit messages in 220-gc-sections and 304-mips_disable_fpu
fix 050-backport_netfilter_rtcache to match new API
update inlined dma ops with upstream changes
add missing config symbols
enabled CONFIG_MULTIUSER
update kmod defintions for 4.1
]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46112
On two tested devices: Netgear R6250 (BCM53011 rev 2) and Luxul XWC-1000
(BCM53011 rev 3) it was possible to use port 7 and eth1 (instead of port
5 and eth0). It seems BCM53011 just like BCM53012 has 8 ports and
usually 3 of them are connected to the SoC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46104
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45970
On device reset the sizes for the vlan and port tables were wrongly
calculated based on the pointer size instead of the struct size. This
causes buffer overruns on 64 bit targets, resulting in panics.
Fix this by dereferencing the pointers.
Reported-by: Fedor Konstantinov <blmink@mink.su>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45938
At least on my b53 chip, the mask is 3 bits wide, and because
of this some STP states are not set properly and discarded when read.
Maybe for some other chips it makes sense to have just 2 bits width,
but I don't have other versions around to test/validate.
If that's the case then maybe we could add another STP state mask.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45937
STMMAC_PLATFORM and STMMAC_PCI have been added recently in the kernel,
but show up only when STMMAC driver is enabled. So se'll add it in the
generic config, so the kernel build doesn't stall whenever we enable
this driver.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45828
With this patch the following two patches are backported:
* bridge: fix parsing of MLDv2 reports
* bridge: allow setting hash_max + multicast_router if interface is down
The former one is an important fix which got just applied to the net-tree
and is queued for stable. The latter is a patch which is needed to make
the hash_max and multicast_router attributes configurable through
netifd.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 45783
Update kernel sources and refresh some patches.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45761
Commit 5168c9a5702648eb690d32ec821647aca80aeba9 introduced a regression
during patch application on the 4.0 kernel. Some of the patched content
doesn't match the actual code, therefore leading to the following error:
Applying patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch
patching file net/ipv6/ip6_output.c
Hunk #1 FAILED at 886.
1 out of 1 hunk FAILED -- rejects in file net/ipv6/ip6_output.c
patching file net/ipv6/route.c
Hunk #1 succeeded at 2247 (offset 2 lines).
Patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch does not apply (enforce with -f)
This change just adapts the actual patch to fix what is in kernel 4.0
and make it apply cleanly.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45705
This chipset has at least 8 usable ports, e.g. Netgear R8000 has ports
5, 7 and 8 connected to Ethernet interfaces:
vlan1ports=0 1 2 3 5 7 8*
vlan2ports=4 8u
Port 6 seems to be always disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45676
Since the kernel/rootfs split handling was modified 2 years ago by r37283 (
https://dev.openwrt.org/changeset/37283 ) and by the subsequent checkins,
users have seen rather scary mtd errors in the log at every boot. The message
ends "-- forcing read-only", which looks a bit error-like. That error has
been mentioned in some forum threads, when users have noticed this message
instead of some actual error.
[ 2.940000] 0x000000070000-0x000000ff0000 : "firmware"
[ 2.970000] 2 netgear-fw partitions found on MTD device firmware
[ 2.970000] 0x000000070000-0x000000188440 : "kernel"
[ 2.980000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 2.990000] 0x000000188440-0x000000ff0000 : "rootfs"
The patch removes the rather useless warning message.
signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45669
This option has been added in kernel 3.17. It shows-up only when both
ARCH_QCOM and CRYPTO are enabled. So we'll disable these two by default
to avoid stalling the build when these conditions are met.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45658
I still need to test following patch before backporting:
bgmac: leave interrupts disabled as long as there is work to do
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45571
Linux 4.0 was released on 2014-04-12
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45559
-removed symbol because it should be handled by wpan.mk
-add missing FAKEHARD symbol (this symbol is removed in Kernel 4.0)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45530
Refresh patches to remove the trailing whitespaces caused by an old
diffutils version on osx.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45506
it has been non-functional for years and caused numerous memleaks and
crashes for people that tried to enable it.
it has no maintained upstream source, and it does not look like it's
going to be fixed any time soon
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45423
On BCM5301X there are two different cases to handle: CPU port 8 vs. any
other one. Support for CPU port 8 was already partially implemented but
it lacked setting some extra bit for 2G speed. It also will need to be
extended to implement "SMP dual core 3 GMAC setup". That's the reason
for handling it in separated code block.
This patch also adds overriding CPU port state for port other than 8. It
requires using recently defined GMII_PORT registers.
It was tested for regressions on BCM53011 revs 2 & 3. It was also
confirmed to fix switch on some internal Broadcom board.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45402
It currently does not seem to make a difference anymore, except by
increasing compressed kernel image size
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45385
* properly enclose macro arguments in paranthesis on use
* remove trailing white space
* convert C99 // comments
* add missing blank lines after declaration
* remove braces from single statement blocks
* split lines > 80 chars (except for one)
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45356
These missing options have been noticed while enabling the following
configuration options on ipq806x, but they're available in the standard
kernel:
*ARCH_QCOM
*CONFIG_USB_SUPPORT
*CONFIG_USB_DWC3
*CONFIG_MFD_SYSCON
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45256
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
v2: changes in input.mk broke the patch, some of the CONFIG_SND_*
stuff was added already
SVN-Revision: 45205
Enabling this option renames the bootloader supplied root=
and rootfstype= variables, which might have to be know but
would break the automatisms OpenWrt uses.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45196
Use the latest version of the yaffs code. Fetched from the
yaffs2 git tree and it is based on the following commit:
commit 7e5cf0fa1b694f835cdc184a8395b229fa29f9ae
Author: Charles Manning <cdhmanning@gmail.com>
Date: Thu Aug 7 11:25:05 2014 +1200
yaffs-direct: Basic tests. Add lpthread flag for background gc support
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45188
This backports upstream commit 702131e2a393b45174be326f1dbe20b658b4f157
bcma: move PCI IRQ control function to host specific code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44969
also refresh generic patches for 3.14, 3.18, 3.19 and 4.0
targets might need a minor refresh as well, however, it looks
like everything still applies cleanly with occasional small
offsets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44876
If this option is enabled, the FIT image format will be detected and
split by the mtdsplit code. Detection is based upon the FDT magic, which
will trigger the parsing and detection of the rootfs, ending-up in the
creation of the 2 new partitions.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44792
It will now actually enable the mib counters instead of enabling rx/tx for
the first switch port.
Reported-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44788
This commit re-adds a patch from 3.14 that is required for UBI block
devices with an EOF marker to be successfully mounted.
Signed-off-by: Oliver Smith <oliver@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa>
SVN-Revision: 44658
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44614
HAMRADIO enabled in all generic configs, but no one platform directly
use related drivers/protocols. This symbol is only used for kmod-ax25
package modules. Furthermore, half of platforms explicitly disables
this symbol, what silently disables build of modules for kmod-ax25
package.
So disable HAMRADIO by-default in generic config, add it to kmod-ax25
package and remove it from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44613
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44612
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44583
For bcm63xx integrated switches, broadcom changed the data endianess
to match the system endianess. But this only applies to within one word,
which causes 48/64 bit values to be still split into their "litte endian"
groups.
E.g. 48 bit values (with 5 being the most significant byte) aligned
0x00 ..01 or 0123
0x04 2345 45..
will become
0x00 ..10 resp. 3210
0x04 5432 54..
Likewise for 64 bit values.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44568
Remove the need for the header file to be exported - we don't need most
of it anyway; all we care about are the offset of the rootfs length and
header crc fields.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44557
- Allow --command-line parameters of kexec-tools be parsed and used by
the kernel.
- For malta machine, mark kernel code and kernel data segments as
"System RAM" instead of "reserved" in /proc/iomem, otherwise
kexec-tools will complain that program segments in ELF kernel file
are invalid.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 44429
We shouldn't read data directly into the header struct, as some devices
(e.g. Edimax) need more bytes due to some extra header.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44414
Some devices have uImage headers after some extra headers (e.g. Edimax
devices). To support such cases our verify callback function should be
allowed to return header offset, not just a boolean value.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44412
drivers/net/phy/adm6996.c:881:5: warning: format '%lu' expects argument of type 'long unsigned int', but argument 5 has type 'u32' [-Wformat=]
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44333
Related to debug/tracing, only added to 3.14+, might be needed for older versions as well
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44323
Some devices out there only have a NOR flash to store the rootfs on.
While using UBI is arguable on this kind of flash, this is something that should
be supported.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44260
It fails to build because of missing of_irq_parse_raw and incompatible
irq_create_of_mapping.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44230
Replace the now defunct 062-mips_decompressor_build_fix.patch with another
patch that simply undefines the arch memset and memcpy defines to avoid
syntax errors in the redeclaration.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44223
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
Changeset r43049 removed the "062-mips_decompressor_build_fix.patch" which is
still required to properly build the xburst kernel.
Fix the syntax error in the preprocessed code by explicitely undefining the
"memcpy" and "memset" macros prior to declaring the replacements functions.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44133
Jonas Gorski
Hauke Mehrtens
Rafał Miłecki
Felix Fietkau
John Crispin
Imre Kaloz
Steven Barth
Luka Perkov
Zoltan Herpai
Gabor Juhos
Florian Fainelli
Nicolas Thill
Jo-Philipp Wich